The branch contains driver changes that are tightly
connected to SoC specific code. Aside from smaller
cleanups and bug fixes, here is a list of the notable
changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver
for its on-board pluggable extension bus. The
same platform also gains a firmware driver.
- The Samsung Exynos family gains a new Chipid driver
exporting using the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon
chips.
- A firmware driver for the NXP i.MX DSP IPC protocol
using shared memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the
NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for
the S905X3 and A311D chips
- A rework of the TI Davinci framebuffer driver to
allow important cleanups in the platform code
- A couple of device drivers for removed ARM SoC
platforms are removed. Most of the removals were
picked up by other maintainers, this contains
whatever was left.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lxFi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This contains driver changes that are tightly connected to SoC
specific code. Aside from smaller cleanups and bug fixes, here is a
list of the notable changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver for its
on-board pluggable extension bus. The same platform also gains a
firmware driver.
- The Samsung Exynos family gains a new Chipid driver exporting using
the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon chips.
- A firmware driver for the NXP i.MX DSP IPC protocol using shared
memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for the S905X3 and A311D
chips
- A rework of the TI Davinci framebuffer driver to allow important
cleanups in the platform code
- A couple of device drivers for removed ARM SoC platforms are
removed. Most of the removals were picked up by other maintainers,
this contains whatever was left"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
bus: uniphier-system-bus: use devm_platform_ioremap_resource()
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
bus: imx-weim: remove incorrect __init annotations
fbdev: remove w90x900/nuc900 platform drivers
spi: remove w90x900 driver
net: remove w90p910-ether driver
net: remove ks8695 driver
firmware: turris-mox-rwtm: Add sysfs documentation
firmware: Add Turris Mox rWTM firmware driver
dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
bus: moxtet: fix unsigned comparison to less than zero
bus: moxtet: remove set but not used variable 'dummy'
ARM: scoop: Use the right include
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
...
Starting with commit 72175d4ea4 ("driver core: Make driver core
own stateful device links") stateful device links are owned by the
driver core and should not be explicitly removed on device unbind.
Delete all device_link_remove appearances from the dpio driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Adding compatible string "ls1028a-dcfg" to initialize guts driver
for ls1028 and SoC die attribute definition for LS1028A
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
When using the reserved memory node in the device tree there are
two options - dynamic or static. If a dynamic allocation was
selected (where the kernel selects the address for the allocation)
convert it to a static allocation by inserting the reg property.
This will ensure the same memory is reused after a kexec()
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
When shutting down a FQ on a dedicated channel only the
SW portal associated with that channel can dequeue from it.
Make sure the correct portal is use.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The drain_mr_fqni() function may be called fron uninterruptable
context so convert the msleep() to an mdelay(). Also ensure that
the valid bit is updated while polling.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
If the QMan device was previously initialized make sure all the
frame queues are out of service once all the portals are probed.
This handles the case where the kernel is restarted without the
SoC being reset (kexec for example)
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Clean the BMan buffer pools if the device had been initialized
previously. This will ensure a consistent state if the kernel
was soft restarted (kexec for example)
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Rework QBMan private memory setup so that the areas are not
zeroed if the device was previously initialized
If the QMan private memory was already initialized skip the PFDR
initialization.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Thierry Reding <treding@nvidia.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
DPAA2 Console driver
- Add driver to export two char devices to dump logs for MC and
AIOP
DPAA2 DPIO driver
- Add support for memory backed QBMan portals
- Increase the timeout period to prevent false error
- Add APIs to retrieve QBMan portal probing status
DPAA Qman driver
- Only make liodn fixup on powerpc SoCs with PAMU iommu
QUICC Engine
- Add support for importing qe-snums through device tree
- Some cleanups and foot print optimzation
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEhb3UXAyxp6UQ0v6khtxQDvusFVQFAlz4GikACgkQhtxQDvus
FVRCLg/+KEAbNflBF+uo5j7bQeufFSfBhyXzZv3L+RRBvavCeMbv9GkyNZXUcaHH
Lo2m/l/2EH6SCzTj4MPZJ9jXE8Ri6+xkZiMUJG3wzJ0hf8tLPrrmHx0eyPWF40vP
jPOCZQX4ofcrnMI4xlnpn6zPuBnMxm+GDfimY7UfApItoGObIhgF1RNJhdiwLrkn
NnAYPrDYGAS/TPkYnkquA8OlemscPdy2ErdstIBCG+EfO1tgzliJsO9yI16IehJN
Q2BGahAlUO22qOippdrvpsAOw5CgZyFi5quyaqs2oSHQNfPgvFLyaejLVtlMQxIc
XUQU1/hNv/+x9v11ZTNHqN4CrnkCwqlZNtX1X0QU0/APQcDLJoTDCLfcgmxphhVz
ale8t+kRz+Rze/PvA9b+4l3HHgEPR6OCmz2yw+9BJK92uiwNNoLbx2q4tsQHR6r+
95qLDgMaaw8YPP3MIJ5HrTzmIDmr4Vwp/Y/2Osr+sah5iNglKetekZVtB2n+FYNW
rtWPbEOC1gCs8ST4AZNufkucg8ljqPz0Rei3pKp0sP+PCKaoq1pQVg0icS39QPgt
vDfmVlfDOnSL7kHZTOD/SJVza8xtCWGt0UETP2gA3gycnK8kCOgSOpu67HD9Wno8
3+TQgE8qdYlpgJAleo2hbUsFigPlbpzgbCNowGDmKU+RmTBAVPc=
=zaF/
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.3 (take 2)
DPAA2 Console driver
- Add driver to export two char devices to dump logs for MC and
AIOP
DPAA2 DPIO driver
- Add support for memory backed QBMan portals
- Increase the timeout period to prevent false error
- Add APIs to retrieve QBMan portal probing status
DPAA Qman driver
- Only make liodn fixup on powerpc SoCs with PAMU iommu
QUICC Engine
- Add support for importing qe-snums through device tree
- Some cleanups and foot print optimzation
* tag 'soc-fsl-next-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: qe: fold qe_get_num_of_snums into qe_snums_init
soc: fsl: qe: support fsl,qe-snums property
dt-bindings: soc: fsl: qe: document new fsl,qe-snums binding
soc: fsl: qe: introduce qe_get_device_node helper
soc: fsl: qe: reduce static memory footprint by 1.7K
soc: fsl: qe: drop useless static qualifier
soc: fsl: fix spelling mistake "Firmaware" -> "Firmware"
Link: https://lore.kernel.org/r/20190605194511.12127-1-leoyang.li@nxp.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Convert docs to ReST and add them to the arch-specific
book.
The conversion here was trivial, as almost every file there
was already using an elegant format close to ReST standard.
The changes were mostly to mark literal blocks and add a few
missing section title identifiers.
One note with regards to "--": on Sphinx, this can't be used
to identify a list, as it will format it badly. This can be
used, however, to identify a long hyphen - and "---" is an
even longer one.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> # cxl
DPAA2 Console driver
- Add driver to export two char devices to dump logs for MC and
AIOP
DPAA2 DPIO driver
- Add support for memory backed QBMan portals
- Increase the timeout period to prevent false error
- Add APIs to retrieve QBMan portal probing status
DPAA Qman driver
- Only make liodn fixup on powerpc SoCs with PAMU iommu
-----BEGIN PGP SIGNATURE-----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=C+f6
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.3
DPAA2 Console driver
- Add driver to export two char devices to dump logs for MC and
AIOP
DPAA2 DPIO driver
- Add support for memory backed QBMan portals
- Increase the timeout period to prevent false error
- Add APIs to retrieve QBMan portal probing status
DPAA Qman driver
- Only make liodn fixup on powerpc SoCs with PAMU iommu
* tag 'soc-fsl-next-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: qbman_portals: add APIs to retrieve the probing status
soc: fsl: qman: fixup liodns only on ppc targets
soc: fsl: dpio: Add support for memory backed QBMan portals
bus: mc-bus: Add support for mapping shareable portals
soc: fsl: dpio: Increase timeout for QBMan Management Commands
soc: fsl: add DPAA2 console support
Documentation: DT: Add entry for DPAA2 console
soc: fsl: guts: Add definition for LX2160A
Signed-off-by: Olof Johansson <olof@lixom.net>
The comment "No QE ever has fewer than 28 SNUMs" is false; e.g. the
MPC8309 has 14. The code path returning -EINVAL is also a recipe for
instant disaster, since the caller (qe_snums_init) uncritically
assigns the return value to the unsigned qe_num_of_snum, and would
thus proceed to attempt to copy 4GB from snum_init_46[] to the snum[]
array.
So fold the handling of the legacy fsl,qe-num-snums into
qe_snums_init, and make sure we do not end up using the snum_init_46
array in cases other than the two where we know it makes sense.
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Add driver support for the newly introduced fsl,qe-snums property.
Conveniently, of_property_read_variable_u8_array does exactly what we
need: If the property fsl,qe-snums is found (and has an allowed size),
the array of values get copied to snums, and the return value is the
number of snums - we cannot assign directly to num_of_snums, since we
need to check whether the return value is negative.
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The 'try of_find_compatible_node(NULL, NULL, "fsl,qe"), fall back to
of_find_node_by_type(NULL, "qe")' pattern is repeated five
times. Factor it into a common helper.
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The current array of struct qe_snum use 256*4 bytes for just keeping
track of the free/used state of each index, and the struct layout
means there's another 768 bytes of padding. If we just unzip that
structure, the array of snum values just use 256 bytes, while the
free/inuse state can be tracked in a 32 byte bitmap.
So this reduces the .data footprint by 1760 bytes. It also serves as
preparation for introducing another DT binding for specifying the snum
values.
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The local variable snum_init has no reason to have static storage duration.
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 107 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.615055994@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spelling mistake in a pr_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a couple of new APIs to check the probing status of the required
cpu bound qman and bman portals:
'int bman_portals_probed()' and 'int qman_portals_probed()'.
They return the following values.
* 1 if qman/bman portals were all probed correctly
* 0 if qman/bman portals were not yet probed
* -1 if probing of qman/bman portals failed
Portals are considered successful probed if no error occurred during
the probing of any of the portals and if enough portals were probed
to have one available for each cpu.
The error handling paths were slightly rearranged in order to fit this
new functionality without being too intrusive.
Drivers that use qman/bman portal driver services are required to use
these APIs before calling any functions exported by these drivers or
otherwise they will crash the kernel.
First user will be the dpaa1 ethernet driver, coming in a subsequent
patch.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
ARM SoCs use SMMU so the liodn fixup done in the qman driver is no
longer making sense and it also breaks the ICID settings inherited
from u-boot. Do the fixups only for PPC targets.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
NXP devices with QBMan version 5 and above can enable software
portals that are memory backed. This allows the portal to be
mapped as cacheable/sharable (same as all normal memory) so
that portals can freely migrate between cores and clusters
in the SoC. The driver will enable this mode by default when
appropriate HW support is detected.
Signed-off-by: Youri Querry <youri.querry_1@nxp.com>
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The timeout for QBMan Management Commands can falsely trigger on a
busy system. This patch doubles the timeout to avoid the
false error reports
Signed-off-by: Youri Querry <youri.querry_1@nxp.com>
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
This patch adds DPAA2 MC and AIOP console log support.
The platform driver probes on the "fsl,dpaa2-console" device tree node
which describes the base firmware address needed in order to infer the
start address of both firmware logs: MC and AIOP.
It then exports two misc char devices which can be used to dump
the needed logs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Adding compatible string "lx2160a-dcfg" to
initialize guts driver for lx2160 and SoC die
attribute definition for LX2160A
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
We forgot to set "err" on this error path.
Fixes: 1a2d397a6e ("gpio/powerpc: Eliminate duplication of of_get_named_gpio_flags()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP,
NVIDIA, Amlogic and Qualcomm.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=+DOl
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP, NVIDIA,
Amlogic and Qualcomm"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (113 commits)
tee: optee: update optee_msg.h and optee_smc.h to dual license
tee: add cancellation support to client interface
dpaa2-eth: configure the cache stashing amount on a queue
soc: fsl: dpio: configure cache stashing destination
soc: fsl: dpio: enable frame data cache stashing per software portal
soc: fsl: guts: make fsl_guts_get_svr() static
hwrng: make symbol 'optee_rng_id_table' static
tee: optee: Fix unsigned comparison with less than zero
hwrng: Fix unsigned comparison with less than zero
tee: fix possible error pointer ctx dereferencing
hwrng: optee: Initialize some structs using memset instead of braces
tee: optee: Initialize some structs using memset instead of braces
soc: fsl: dpio: fix memory leak of a struct qbman on error exit path
clk: tegra: dfll: Make symbol 'tegra210_cpu_cvb_tables' static
soc: qcom: llcc-slice: Fix typos
qcom: soc: llcc-slice: Consolidate some code
qcom: soc: llcc-slice: Clear the global drv_data pointer on error
drivers: soc: xilinx: Add ZynqMP power domain driver
firmware: xilinx: Add APIs to control node status/power
dt-bindings: power: Add ZynqMP power domain bindings
...
Pull crypto update from Herbert Xu:
"API:
- Add helper for simple skcipher modes.
- Add helper to register multiple templates.
- Set CRYPTO_TFM_NEED_KEY when setkey fails.
- Require neither or both of export/import in shash.
- AEAD decryption test vectors are now generated from encryption
ones.
- New option CONFIG_CRYPTO_MANAGER_EXTRA_TESTS that includes random
fuzzing.
Algorithms:
- Conversions to skcipher and helper for many templates.
- Add more test vectors for nhpoly1305 and adiantum.
Drivers:
- Add crypto4xx prng support.
- Add xcbc/cmac/ecb support in caam.
- Add AES support for Exynos5433 in s5p.
- Remove sha384/sha512 from artpec7 as hardware cannot do partial
hash"
[ There is a merge of the Freescale SoC tree in order to pull in changes
required by patches to the caam/qi2 driver. ]
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (174 commits)
crypto: s5p - add AES support for Exynos5433
dt-bindings: crypto: document Exynos5433 SlimSSS
crypto: crypto4xx - add missing of_node_put after of_device_is_available
crypto: cavium/zip - fix collision with generic cra_driver_name
crypto: af_alg - use struct_size() in sock_kfree_s()
crypto: caam - remove redundant likely/unlikely annotation
crypto: s5p - update iv after AES-CBC op end
crypto: x86/poly1305 - Clear key material from stack in SSE2 variant
crypto: caam - generate hash keys in-place
crypto: caam - fix DMA mapping xcbc key twice
crypto: caam - fix hash context DMA unmap size
hwrng: bcm2835 - fix probe as platform device
crypto: s5p-sss - Use AES_BLOCK_SIZE define instead of number
crypto: stm32 - drop pointless static qualifier in stm32_hash_remove()
crypto: chelsio - Fixed Traffic Stall
crypto: marvell - Remove set but not used variable 'ivsize'
crypto: ccp - Update driver messages to remove some confusion
crypto: adiantum - add 1536 and 4096-byte test vectors
crypto: nhpoly1305 - add a test vector with len % 16 != 0
crypto: arm/aes-ce - update IV after partial final CTR block
...
DPIO driver
- Add support for cache stashing and enable it in dpaa2-eth driver
GUTS driver
- Make fsl_guts_get_svr() API internal in favor of more generic
soc_device_match()
-----BEGIN PGP SIGNATURE-----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=tNfD
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.1 take4
DPIO driver
- Add support for cache stashing and enable it in dpaa2-eth driver
GUTS driver
- Make fsl_guts_get_svr() API internal in favor of more generic
soc_device_match()
* tag 'soc-fsl-next-v5.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
dpaa2-eth: configure the cache stashing amount on a queue
soc: fsl: dpio: configure cache stashing destination
soc: fsl: dpio: enable frame data cache stashing per software portal
soc: fsl: guts: make fsl_guts_get_svr() static
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Depending on the SoC version and the CPU id, configure the cache
stashing destination for a specific dpio.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Enable cache stashing on the frame data dequeued using this software
portal. Also, enable dropping a stash request transaction when the
target request queue is almost full.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The export of fsl_guts_get_svr() is a left-over, it's currently used
only internally and users needing SoC information should use the generic
soc_device infrastructure.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
DPIO driver
- fixed a use after free problem
- fixed a memory leak on error path
-----BEGIN PGP SIGNATURE-----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=GogM
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.1 take3
DPIO driver
- fixed a use after free problem
- fixed a memory leak on error path
* tag 'soc-fsl-next-v5.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: dpio: fix memory leak of a struct qbman on error exit path
soc: fsl: dpio: Use after free in dpaa2_dpio_remove()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently the error check for a null reg leaks a struct qbman
that was allocated earlier. Fix this by kfree'ing p on the error exit
path.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The dpaa2_io_down(priv->io) call frees "priv->io" so I've shifted the
code around a little bit to avoid the use after free.
Fixes: 991e873223 ("soc: fsl: dpio: use a cpumask to identify which cpus are unused")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
DPIO driver
- Clean up the remove path in the dpio driver so that successive
bind/unbind commands behave properly
- Add the ability to automatically create a device link between a
consumer device on the fsl-mc bus and a supplier one
- Add prefetch to dpio dequeue to improve performance
- Update the type of dpio APIs to align with buffer pool id register
field
guts driver
- Prevent allocation failure by reuse the machine type data from device
tree directly
-----BEGIN PGP SIGNATURE-----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=0PWU
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.1
DPIO driver
- Clean up the remove path in the dpio driver so that successive
bind/unbind commands behave properly
- Add the ability to automatically create a device link between a
consumer device on the fsl-mc bus and a supplier one
- Add prefetch to dpio dequeue to improve performance
- Update the type of dpio APIs to align with buffer pool id register
field
guts driver
- Prevent allocation failure by reuse the machine type data from device
tree directly
* tag 'soc-fsl-next-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: guts: reuse machine name from device tree
soc: fsl: dpio: Change bpid type to u16
soc: fsl: dpio: Add prefetch instruction
bus: fsl-mc: automatically add a device_link on fsl_mc_[portal,object]_allocate
soc: fsl: dpio: add a device_link at dpaa2_io_service_register
soc: fsl: dpio: store a backpointer to the device backing the dpaa2_io
soc: fsl: dpio: keep a per dpio device MC portal
soc: fsl: dpio: perform DPIO Reset on Probe
soc: fsl: dpio: use a cpumask to identify which cpus are unused
soc: fsl: dpio: cleanup the cpu array on dpaa2_io_down
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
By clearing all interrupt sources, not only those that
already occurred, the existing code may acknowledge by
mistake interrupts that occurred after the code checks
for them.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Pull networking fixes from David Miller:
1) Fix regression in multi-SKB responses to RTM_GETADDR, from Arthur
Gautier.
2) Fix ipv6 frag parsing in openvswitch, from Yi-Hung Wei.
3) Unbounded recursion in ipv4 and ipv6 GUE tunnels, from Stefano
Brivio.
4) Use after free in hns driver, from Yonglong Liu.
5) icmp6_send() needs to handle the case of NULL skb, from Eric
Dumazet.
6) Missing rcu read lock in __inet6_bind() when operating on mapped
addresses, from David Ahern.
7) Memory leak in tipc-nl_compat_publ_dump(), from Gustavo A. R. Silva.
8) Fix PHY vs r8169 module loading ordering issues, from Heiner
Kallweit.
9) Fix bridge vlan memory leak, from Ido Schimmel.
10) Dev refcount leak in AF_PACKET, from Jason Gunthorpe.
11) Infoleak in ipv6_local_error(), flow label isn't completely
initialized. From Eric Dumazet.
12) Handle mv88e6390 errata, from Andrew Lunn.
13) Making vhost/vsock CID hashing consistent, from Zha Bin.
14) Fix lack of UMH cleanup when it unexpectedly exits, from Taehee Yoo.
15) Bridge forwarding must clear skb->tstamp, from Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
bnxt_en: Fix context memory allocation.
bnxt_en: Fix ring checking logic on 57500 chips.
mISDN: hfcsusb: Use struct_size() in kzalloc()
net: clear skb->tstamp in bridge forwarding path
net: bpfilter: disallow to remove bpfilter module while being used
net: bpfilter: restart bpfilter_umh when error occurred
net: bpfilter: use cleanup callback to release umh_info
umh: add exit routine for UMH process
isdn: i4l: isdn_tty: Fix some concurrency double-free bugs
vhost/vsock: fix vhost vsock cid hashing inconsistent
net: stmmac: Prevent RX starvation in stmmac_napi_poll()
net: stmmac: Fix the logic of checking if RX Watchdog must be enabled
net: stmmac: Check if CBS is supported before configuring
net: stmmac: dwxgmac2: Only clear interrupts that are active
net: stmmac: Fix PCI module removal leak
tools/bpf: fix bpftool map dump with bitfields
tools/bpf: test btf bitfield with >=256 struct member offset
bpf: fix bpffs bitfield pretty print
net: ethernet: mediatek: fix warning in phy_start_aneg
tcp: change txhash on SYN-data timeout
...
Reuse the string machine from the device tree data structure instead
of duplicating the data again. This also prevents a potential memory
allocation failure that was not handled previously. Also fixes an early
put of root device node.
Reported-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
In all QBMan registers, the buffer pool id field is two bytes long.
The low level qbman APIs reflect this, but the high level DPIO ones
use u32. Modify them in order to avoid implicit downcasts.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Automatically add a device link between the actual device requesting the
dpaa2_io_service_register and the underlying dpaa2_io used. This link
will ensure that when a DPIO device, which is indirectly used by other
devices, is unbound any consumer devices will be also unbound from their
drivers.
For example, any DPNI, bound to the dpaa2-eth driver, which is using
DPIO devices will be unbound before its supplier device.
Also, add a new parameter to the dpaa2_io_service_[de]register functions
to specify the requesting device (ie the consumer).
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
In dpaa2_io_store_next(), if the current dequeue entry is not
the last, prefetch the next one as most likely it will be
requested shortly by the consumer driver.
This brings a ~3% improvement for dpaa2 ethernet driver
IP forwarding with small size frames.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Add a new field in the dpaa2_io structure to hold a backpointer to the
actual DPIO device.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
At the moment, the dpio-driver allocates an MC portal at probe time and
frees it right after usage. The same thing happens on the remove path.
This behavior could lead to scenarios where an MC portal is available
for use at probing but not longer free on the remove path which could
lead to unproper unbind of resources.
Change the driver's behavior in such a way that an MC portal is
allocated at probe and kept until the DPIO device is removed. This will
ensure that at any time after a DPIO device was successfully probed, all
its dependencies will be met.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Linus Torvalds