Instead of tying mesh activity to interface up,
add join and leave commands for mesh. Since we
must be backward compatible, let cfg80211 handle
joining a mesh if a mesh ID was pre-configured
when the device goes up.
Note that this therefore must modify mac80211 as
well since mac80211 needs to lose the logic to
start the mesh on interface up.
We now allow querying mesh parameters before the
mesh is connected, which simply returns defaults.
Setting them (internally renamed to "update") is
only allowed while connected. Specify them with
the new mesh join command instead where needed.
In mac80211, beaconing must now also follow the
mesh enabled/not enabled state, which is done
by testing the mesh ID.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I'm going to need this in a new place later.
Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 used to do all its bookkeeping in
the notifier, but some new stuff will have
to use local variables so make the callback
return the netdev pointer.
Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TTL in path selection information elements is different from
the mesh ttl used in mesh data frames. Version 7.03 of the 11s
draft calls this ttl 'Element TTL'.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With p2p, it is sometimes necessary to transmit
a frame (typically an action frame) on another
channel than the current channel. Enable this
through the CMD_FRAME API, and allow it to wait
for a response. A new command allows that wait
to be aborted.
However, allow userspace to specify whether or
not it wants to allow off-channel TX, it may
actually want to use the same channel only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the ability for drivers to use CQM events
to notify about packet loss for specific stations
(which could be the AP for the managed mode case).
Since the threshold might be determined by the
driver (it isn't passed in right now) it will be
passed out of the driver to userspace in the event.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- store the multicast rate as an index instead of the rate value
(reduces cpu overhead in a hotpath)
- validate the rate values (must match a bitrate in at least one sband)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.
This uses the recently added generic EWMA library function.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow setting of TX and RX antennas configuration via nl80211.
The antenna configuration is defined as a bitmap of allowed antennas to use.
This API can be used to mask out antennas which are not attached or should not
be used for other reasons like regulatory concerns or special setups.
Separate bitmaps are used for RX and TX to allow configuring different antennas
for receiving and transmitting. Each bitmap is 32 bit long, each bit
representing one antenna, starting with antenna 1 at the first bit. If an
antenna bit is set, this means the driver is allowed to use this antenna for RX
or TX respectively; if the bit is not set the hardware is not allowed to use
this antenna.
Using bitmaps has the benefit of allowing for a flexible configuration
interface which can support many different configurations and which can be used
for 802.11n as well as non-802.11n devices. Instead of relying on some hardware
specific assumptions, drivers can use this information to know which antennas
are actually attached to the system and derive their capabilities based on
that.
802.11n devices should enable or disable chains, based on which antennas are
present (If all antennas belonging to a particular chain are disabled, the
entire chain should be disabled). HT capabilities (like STBC, TX Beamforming,
Antenna selection) should be calculated based on the available chains after
applying the antenna masks. Should a 802.11n device have diversity antennas
attached to one of their chains, diversity can be enabled or disabled based on
the antenna information.
Non-802.11n drivers can use the antenna masks to select RX and TX antennas and
to enable or disable antenna diversity.
While covering chainmasks for 802.11n and the standard "legacy" modes "fixed
antenna 1", "fixed antenna 2" and "diversity" this API also allows more rare,
but useful configurations as follows:
1) Send on antenna 1, receive on antenna 2 (or vice versa). This can be used to
have a low gain antenna for TX in order to keep within the regulatory
constraints and a high gain antenna for RX in order to receive weaker signals
("speak softly, but listen harder"). This can be useful for building long-shot
outdoor links. Another usage of this setup is having a low-noise pre-amplifier
on antenna 1 and a power amplifier on the other antenna. This way transmit
noise is mostly kept out of the low noise receive channel.
(This would be bitmaps: tx 1 rx 2).
2) Another similar setup is: Use RX diversity on both antennas, but always send
on antenna 1. Again that would allow us to benefit from a higher gain RX
antenna, while staying within the legal limits.
(This would be: tx 0 rx 3).
3) And finally there can be special experimental setups in research and
development even with pre 802.11n hardware where more than 2 antennas are
available. It's good to keep the API simple, yet flexible.
Signed-off-by: Bruno Randolf <br1@einfach.org>
--
v7: Made bitmasks 32 bit wide and rebased to latest wireless-testing.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IS_ERR and PTR_ERR were called with the wrong pointer, leading to a
crash when cfg80211_get_dev_from_ifindex fails.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using these, user space can calculate a relative channel utilization
with arbitrary intervals by regularly taking snapshots of the survey
results.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need for the WDS peer address
to not be const, so make it const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Jordan's patch to allow setting the WDS
peer crossed with my patch removing all the
boilerplate code in nl80211, and consequently
he didn't make use of it yet. Fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This information is already available in mac80211, we just need to export it
via cfg80211 and nl80211.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yikes! The error return keeps a netdev reference
and the rdev mutex locked, fix that!
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds API to allow adding per-station GTKs,
updates mac80211 to support it, and also allows
drivers to remove a key from hwaccel again when
this may be necessary due to multiple GTKs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consolidate boilerplate code needed for .dumpit
calls operating on netdevs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a new flag that requires the netdev to be
UP and use it to check instead of coding the
check into all functions that require it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes nl80211 use the new genetlink
pre_doit/post_doit hooks for locking and
checking the interface/wiphy index.
This significantly reduces the code size
and the likelihood of locking errors.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added a nl interface to set the peer bssid of a WDS interface.
Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add missing unlocking of the wiphy in set_channel,
and don't try to unlock a non-existing wiphy in
set_cqm.
Cc: stable@kernel.org [2.6.35+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable management frame transmission and subscribing
to management frames through nl80211 in both cfg80211
and mac80211. Also update a few places that I forgot
to update for P2P-client mode previously, and fix a
small bug with non-action frames in this API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some user space applications only want to display survey data for
the operating channel, however there is no API to get that yet.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IBSS started from wireless extensions is currently
missing basic rate configuration, fix this by moving
the code to generate the default to the common code
that gets invoked for both nl80211 and wext.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If interface does not existk, when nl80211_set_power_save is called, (eg.
module has been unloaded) it has been causing kernel panic. Added new
goto target to avoid crash if get_rdev_dev_by_info_ifindex does not
return dev and rdev pointers.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds P2P-STA and P2P-GO as device types so
we can distinguish between those and normal STA
or AP (respectively) type interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a path in nl80211_set_wiphy where result is tested but
uninitialized.
I am hitting this path when I attempt:
sh# iw dev wlan0 set channel 10
command failed: Unknown error 1069727332 (-1069727332)
Signed-off-by: William Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some vendor specified mechanisms for 802.1X-style
functionality use a different protocol than EAP
(even if EAP is vendor-extensible). Allow setting
the ethertype for the protocol when a driver has
support for this. The default if unspecified is
EAP, of course.
Note: This is suitable only for station mode, not
for AP implementation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 95a6ccbb46c70cff376684c752831c014c87029d
Author: Johannes Berg <johannes.berg@intel.com>
Date: Thu Aug 12 15:38:38 2010 +0200
cfg80211/mac80211: extensible frame processing
introduced a netlink bug that caused parsing errors
in userspace because it forgot to close a nesting,
which would advertise a nesting length of zero to
userspace, which then completely threw off parsing
and led to
Illegal nla->nla_type == 0
being printed by libnl.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to register for more than just
action frames by giving the frame subtype, and
make it possible to use this in various modes
as well.
With some tweaks and some added functionality
this will, in the future, also be usable in AP
mode and be able to replace the cooked monitor
interface currently used in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When shared key auth is requested, cfg80211
should verify that the device is capable of
WEP crypto which is required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of errors during message composing msg should be freed after canceling.
Signed-off-by: Yuri Kululin <ext-yuri.kululin@nokia.com>
Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanse found that nl80211_set_wiphy imporperly handles a lock and netdev
reference and contains unreachable code. It is because there return statement
isntead of assignment to result variable. Fix that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jouni Malinen <j@w1.fi>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds transmit power setting type and transmit power level attributes
to NL80211_CMD_SET_WIPHY in order to facilitate adjusting of the transmit power
level of the device.
The added attributes allow selection of automatic, limited or fixed transmit
power level, with the level definable in signed mBm format.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Register net_bridge_port pointer as rx_handler data pointer. As br_port is
removed from struct net_device, another netdev priv_flag is added to indicate
the device serves as a bridge port. Also rcuized pointers are now correctly
dereferenced in br_fdb.c and in netfilter parts.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to nl80211 and mac80211 to set basic rates when
joining/creating ibss network.
Original patch was posted by Johannes Berg on the linux-wireless posting list.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When in IBSS mode, currently action frame TX and RX
cannot be used. Allow using it to talk to any peer,
or for public action frames. Also, while at it,
restructure the code in mac80211 to make it easier
to add this for other interface types in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending action frames, we want to verify
that we do that on the correct channel. However,
checking the channel type in addition can get in
the way, since the channel type could change on
the fly during an association, and it's not
useful to have the channel type anyway since it
has no effect on the transmission. Therefore,
make it optional to specify so that if wanted,
it can still be checked, but is not required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Specifying a valid channel type will get
goto out rather than continuing, due to
missing braces. This affects both remain
on channel and action frame TX commands.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently (all tested with hwsim) you can do stupid
things like setting up an AP on a certain channel,
then adding another virtual interface and making
that associate on another channel -- this will make
the beaconing to move channel but obviously without
the necessary IEs data update.
In order to improve this situation, first make the
configuration APIs (cfg80211 and nl80211) aware of
multi-channel operation -- we'll eventually need
that in the future anyway. There's one userland API
change and one API addition. The API change is that
now SET_WIPHY must be called with virtual interface
index rather than only wiphy index in order to take
effect for that interface -- luckily all current
users (hostapd) do that. For monitor interfaces, the
old setting is preserved, but monitors are always
slaved to other devices anyway so no guarantees.
The second userland API change is the introduction
of a per virtual interface SET_CHANNEL command, that
hostapd should use going forward to make it easier
to understand what's going on (it can automatically
detect a kernel with this command).
Other than mac80211, no existing cfg80211 drivers
are affected by this change because they only allow
a single virtual interface.
mac80211, however, now needs to be aware that the
channel settings are per interface now, and needs
to disallow (for now) real multi-channel operation,
which is another important part of this patch.
One of the immediate benefits is that you can now
start hostapd to operate on a hardware that already
has a connection on another virtual interface, as
long as you specify the same channel.
Note that two things are left unhandled (this is an
improvement -- not a complete fix):
* different HT/no-HT modes
currently you could start an HT AP and then
connect to a non-HT network on the same channel
which would configure the hardware for no HT;
that can be fixed fairly easily
* CSA
An AP we're connected to on a virtual interface
might indicate switching channels, and in that
case we would follow it, regardless of how many
other interfaces are operating; this requires
more effort to fix but is pretty rare after all
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used to configure APs to not bridge traffic between connected stations.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 is quite strict on allowing authentication and association
commands only in certain states. In order to meet these requirements,
user space applications may need to clear authentication or
association state in some cases. Currently, this can be done with
deauth/disassoc command, but that ends up sending out Deauthentication
or Disassociation frame unnecessarily. Add a new nl80211 attribute to
allow this sending of the frame be skipped, but with all other
deauth/disassoc operations being completed.
Similar state change is also needed for IEEE 802.11r FT protocol in
the FT-over-DS case which does not use Authentication frame exchange
in a transition to another BSS. For this to work with cfg80211, an
authentication entry needs to be created for the target BSS without
sending out an Authentication frame. The nl80211 authentication
command can be used for this purpose, too, with the new attribute to
indicate that the command is only for changing local state. This
enables wpa_supplicant to complete FT-over-DS transition successfully.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iw dev <devname> station del <MAC address> is quiet useful in mesh mode and should be possible.
Signed-off-by: Marco Porsch <marco.porsch@siemens.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Add support for basic configuration of a connection quality monitoring to the
nl80211 interface, and basic support for notifying about triggered monitoring
events.
Via this interface a user-space connection manager may configure and receive
pre-warning events of deteriorating WLAN connection quality, and start
preparing for roaming in advance, before the connection is already lost.
An example usage of such a trigger is starting scanning for nearby AP's in
an attempt to find one with better connection quality, and associate to it
before the connection characteristics of the existing connection become too bad
or the association is even lost, leading in a prolonged delay in connectivity.
The interface currently supports only RSSI, but it could be later extended
to include other parameters, such as signal-to-noise ratio, if need for that
arises.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The most needed command from nl80211, which Wireless Extensions had,
is support for power save mode. Add a simple command to make it possible
to enable and disable power save via nl80211.
I was also planning about extending the interface, for example adding the
timeout value, but after thinking more about this I decided not to do it.
Basically there were three reasons:
Firstly, the parameters for power save are very much hardware dependent.
Trying to find a unified interface which would work with all hardware, and
still make sense to users, will be very difficult.
Secondly, IEEE 802.11 power save implementation in Linux is still in state
of flux. We have a long way to still to go and there is no way to predict
what kind of implementation we will have after few years. And because we
need to support nl80211 interface a long time, practically forever, adding
now parameters to nl80211 might create maintenance problems later on.
Third issue are the users. Power save parameters are mostly used for
debugging, so debugfs is better, more flexible, interface for this.
For example, wpa_supplicant currently doesn't configure anything related
to power save mode. It's better to strive that kernel can automatically
optimise the power save parameters, like with help of pm qos network
and other traffic parameters.
Later on, when we have better understanding of power save, we can extend
this command with more features, if there's a need for that.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make remaining netlink policies as const.
Fixup coding style where needed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements a new command to register for action frames
that userspace wants to handle instead of the in-kernel
rejection. It is then responsible for rejecting ones that
it decided not to handle. There is no unregistration, but
the socket can be closed for that.
Frames that are not registered for will not be forwarded
to userspace and will be rejected by the kernel, the
cfg80211 API helps implementing that.
Additionally, this patch adds a new command that allows
doing action frame transmission from userspace. It can be
used either to exchange action frames on the current
operational channel (e.g., with the AP with which we are
currently associated) or to exchange off-channel Public
Action frames with the remain-on-channel command.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As discussed in linux-wireless mailing list, adding and removing
stations for mesh topologies is not necessary. Since doing it triggers
bugs, the sugestion was to simply disable it.
Tested using a custom iw command "station new". Works only after using
hostapd. "station del" command also works.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Simon Raffeiner <sturmflut@lieberbiber.de>
Cc: Andrey Yurovsky <andrey@cozybit.com>
Cc: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nl80211_associate() was rejecting (re)association attempts with EBUSY
in some cases where we are currently associated with an AP that uses
different channel from the destination AP. Fix this by passing the
current wdev to rdev_fixed_channel() in the same way that was already
done for join-IBSS and connect commands. This allows the fixedchan
check to skipped for the current wdev and allows the reassociation to
proceed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Store information elements from Beacon and Probe Response frames in
separate buffers to allow both sets to be made available through
nl80211. This allows user space applications to get access to IEs from
Beacon frames even if we have received Probe Response frames from the
BSS. Previously, the IEs from Probe Response frames would have
overridden the IEs from Beacon frames.
This feature is of somewhat limited use since most protocols include
the same (or extended) information in Probe Response frames. However,
there are couple of exceptions where the IEs from Beacon frames could
be of some use: TIM IE is only included in Beacon frames (and it would
be needed to figure out the DTIM period used in the BSS) and at least
some implementations of Wireless Provisioning Services seem to include
the full IE only in Beacon frames).
The new BSS attribute for scan results is added to allow both the IE
sets to be delivered. This is done in a way that maintains the
previously used behavior for applications that are not aware of the
new NL80211_BSS_BEACON_IES attribute.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new NL80211_CMD_SET_TX_BITRATE_MASK command and related
attributes to provide support for setting TX rate mask for rate
control. This uses the existing cfg80211 set_bitrate_mask operation
that was previously used only with WEXT compat code (SIOCSIWRATE). The
nl80211 command allows more generic configuration of allowed rates as
a mask instead of fixed/max rate.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new attribute NL80211_ATTR_WIPHY_COVERAGE_CLASS sets IEEE 802.11
Coverage Class, which depends on maximum distance of nodes in a
wireless network. It's required for long distance links (more than a few
hundred meters).
The attribute is now ignored by two non-mac80211 drivers, rndis and
iwmc3200wifi, together with WIPHY_PARAM_RETRY_SHORT and
WIPHY_PARAM_RETRY_LONG. If it turns out to be a problem, we could split
set_wiphy_params callback or add new capability bits.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When, for instance, a new IBSS peer is found, userspace
wants to be notified. Add events for all new stations
that mac80211 learns about.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new commands for requesting the driver to remain awake
on a specified channel for the specified amount of time
(and another command to cancel such an operation). This
can be used to implement userspace-controlled off-channel
operations, like Public Action frame exchange on another
channel than the operation channel.
The off-channel operation should behave similarly to scan,
i.e. the local station (if associated) moves into power
save mode to request the AP to buffer frames for it and
then moves to the other channel to allow the off-channel
operation to be completed. The duration parameter can be
used to request enough time to receive a response from
the target station.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, cfg80211 had reported "0" for MCS (i.e. 802.11n) bitrates
through the wireless extensions interface. However, nl80211 was
converting MCS rates into a reasonable bitrate number. This patch moves
the nl80211 code to cfg80211 where it is now shared between both the
nl80211 interface and the wireless extensions interface.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an interface to set, delete and flush PMKIDs through nl80211.
Main users would be fullmac devices which firmwares are capable of
generating the RSN IEs for the re-association requests, e.g. iwmc3200wifi.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A number of people have tried to add a wireless interface
(in managed mode) to a bridge and then complained that it
doesn't work. It cannot work, however, because in 802.11
networks all packets need to be acknowledged and as such
need to be sent to the right address. Promiscuous doesn't
help here. The wireless address format used for these
links has only space for three addresses, the
* transmitter, which must be equal to the sender (origin)
* receiver (on the wireless medium), which is the AP in
the case of managed mode
* the recipient (destination), which is on the APs local
network segment
In an IBSS, it is similar, but the receiver and recipient
must match and the third address is used as the BSSID.
To avoid such mistakes in the future, disallow adding a
wireless interface to a bridge.
Felix has recently added a four-address mode to the AP
and client side that can be used (after negotiating that
it is possible, which must happen out-of-band by setting
up both sides) for bridging, so allow that case.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's very likely that not many devices will support
four-address mode in station or AP mode so introduce
capability bits for both modes, set them in mac80211
and check them when userspace tries to use the mode.
Also, keep track of 4addr in cfg80211 (wireless_dev)
and not in mac80211 any more. mac80211 can also be
improved for the VLAN case by not looking at the
4addr flag but maintaining the station pointer for
it correctly. However, keep track of use_4addr for
station mode in mac80211 to avoid all the derefs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've accumulated a number of options for wiphys
which make more sense as flags as we keep adding
more. Convert the existing ones.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements the NL80211_CMD_GET_SURVEY command and an get_survey()
ops that a driver can implement. The goal of this command is to allow a
drivers to report channel survey data (e.g. channel noise, channel
occupation).
For now, only the mechanism to report back channel noise has been
implemented.
In future, there will either be a survey-trigger command --- or the existing
scan-trigger command will be enhanced. This will allow user-space to
request survey for arbitrary channels.
Note: any driver that cannot report channel noise should not report
any value at all, e.g. made-up -92 dBm.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... which get's rid of three indentical cut-n-paste sections.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Resulting object files have the same MD5 as before.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently it is possible to request a scan on only
disabled channels, which could be problematic for
some drivers. Reject such scans, and also ignore
disabled channels that are given. This resuls in
the scan begin/end event only including channels
that are actually used.
This makes the mac80211 check for disabled channels
superfluous. At the same time, remove the no-IBSS
check from mac80211 -- nothing says that we should
not find any networks on channels that cannot be
used for an IBSS, even when operating in IBSS mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The error unwinding code in set_netns has a bug
that will make it run into a BUG_ON if passed a
bad wiphy index, fix by not trying to unlock a
wiphy that doesn't exist.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Refactor wext to
* split out iwpriv handling
* split out iwspy handling
* split out procfs support
* allow cfg80211 to have wireless extensions compat code
w/o CONFIG_WIRELESS_EXT
After this, drivers need to
- select WIRELESS_EXT - for wext support
- select WEXT_PRIV - for iwpriv support
- select WEXT_SPY - for iwspy support
except cfg80211 -- which gets new hooks in wext-core.c
and can then get wext handlers without CONFIG_WIRELESS_EXT.
Wireless extensions procfs support is auto-selected
based on PROC_FS and anything that requires the wext core
(i.e. WIRELESS_EXT or CFG80211_WEXT).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linux keeps scan results up to 15 seconds. This can be a problem for fast
moving clients: they get back stale data. But if the kernel reports the age
of the BSS items, then user-space can simply weed out old entries by itself.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jump to out_err when the iftype is not supported.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the interface type changes while connected, and the
driver does not require the interface to be down for a
type change, it is currently possible to get very strange
results unless the driver takes special care, which it
shouldn't have to.
To fix this, take care to disconnect/leave IBSS when
changing the interface type -- even if the driver may fail
the call. Also process all events that may be pending to
avoid running into a situation where an event is reported
but only processed after the type has already changed,
which would lead to missing events and warnings.
A side effect of this is that you will have disconnected
or left the IBSS even if the mode change ultimately fails,
but since the intention was to change it and thus leave or
disconnect, this is not a problem.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"cfg80211: validate channel settings across interfaces"
contained a locking bug -- in the managed-mode SIWFREQ
call it would end up running into a lock recursion.
This fixes it by not checking that particular interface
for a channel that it needs to stay on, which is as it
should be as that's the interface we're setting the
channel for.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Kalle Valo <kalle.valo@iki.fi>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The memory layout for scan requests was rather wrong,
we put the scan SSIDs before the channels which could
lead to the channel pointers being unaligned in memory.
It turns out that using a pointer to the channel array
isn't necessary anyway since we can embed a zero-length
array into the struct.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order for userspace to be able to figure out whether
it obtained a consistent snapshot of data or not when
using netlink dumps, we need to have a generation number
in each dump message that indicates whether the list has
changed or not -- its value is arbitrary.
This patch adds such a number to all dumps, this needs
some mac80211 involvement to keep track of a generation
number to start with when adding/removing mesh paths or
stations.
The wiphy and netdev lists can be fully handled within
cfg80211, of course, but generation numbers need to be
stored there as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, there's a problem that affects regulatory
enforcement and connection stability, in that it is
possible to switch the channel while connected to a
network or joined to an IBSS.
The problem comes from the fact that we only validate
the channel against the current interface's type, not
against any other interface. Thus, you have any type
of interface up, additionally bring up a monitor mode
interface and switch the channel on the monitor. This
will obviously also switch the channel on the other
interface.
The problem now is that if you do that while sending
beacons for IBSS mode, you can switch to a disabled
channel or a channel that doesn't allow beaconing.
Combined with a managed mode interface connected to
an AP instead of an IBSS interface, you can easily
break the connection that way.
To fix this, this patch validates any channel change
with all available interfaces, and disallows such
changes on secondary interfaces if another interface
is connected to an AP or joined to an IBSS.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Until now we implemented iwfreq for managed mode, we
needed to keep the implementations separate, but now
that we have all versions implemented we can combine
them and export just one handler.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni and Maxim reported an oops when using wpa_supplicant -Dnl80211,
which seems to be due to random data being contained in the crypto
settings for the assoc() command. This seems to be due to the missing
memset here, so add it -- it's certainly missing but I'm not 100%
certain that it will fix the problem.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis reported this lockdep complaint, that he had also
reported earlier but when trying to analyse I had been
locking at the wrong code, and never saw the problem:
(slightly abridged)
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.31-rc4-wl #6
-------------------------------------------------------
wpa_supplicant/3799 is trying to acquire lock:
(cfg80211_mutex){+.+.+.}, at: [<ffffffffa009246a>] cfg80211_get_dev_from_ifindex+0x1a/0x90 [cfg80211]
but task is already holding lock:
(rtnl_mutex){+.+.+.}, at: [<ffffffff81400ff2>] rtnl_lock+0x12/0x20
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (rtnl_mutex){+.+.+.}:
[<ffffffff810857b6>] __lock_acquire+0xd76/0x12b0
[<ffffffff81085dd3>] lock_acquire+0xe3/0x120
[<ffffffff814ee7a4>] mutex_lock_nested+0x44/0x350
[<ffffffff81400ff2>] rtnl_lock+0x12/0x20
[<ffffffffa009f6a5>] nl80211_send_reg_change_event+0x1f5/0x2a0 [cfg80211]
[<ffffffffa009529e>] set_regdom+0x28e/0x4c0 [cfg80211]
-> #0 (cfg80211_mutex){+.+.+.}:
[<ffffffff8108587b>] __lock_acquire+0xe3b/0x12b0
[<ffffffff81085dd3>] lock_acquire+0xe3/0x120
[<ffffffff814ee7a4>] mutex_lock_nested+0x44/0x350
[<ffffffffa009246a>] cfg80211_get_dev_from_ifindex+0x1a/0x90 [cfg80211]
[<ffffffffa009813f>] get_rdev_dev_by_info_ifindex+0x6f/0xa0 [cfg80211]
[<ffffffffa009b12b>] nl80211_set_interface+0x3b/0x260 [cfg80211]
When looking at the correct code, the problem is quite
obvious. I'm not entirely sure which code paths lead
here, so until I can analyse it better let's just use
RCU to avoid the problem.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to make cfg80211/nl80211 aware of network namespaces,
we have to do the following things:
* del_virtual_intf method takes an interface index rather
than a netdev pointer - simply change this
* nl80211 uses init_net a lot, it changes to use the sender's
network namespace
* scan requests use the interface index, hold a netdev pointer
and reference instead
* we want a wiphy and its associated virtual interfaces to be
in one netns together, so
- we need to be able to change ns for a given interface, so
export dev_change_net_namespace()
- for each virtual interface set the NETIF_F_NETNS_LOCAL
flag, and clear that flag only when the wiphy changes ns,
to disallow breaking this invariant
* when a network namespace goes away, we need to reparent the
wiphy to init_net
* cfg80211 users that support creating virtual interfaces must
create them in the wiphy's namespace, currently this affects
only mac80211
The end result is that you can now switch an entire wiphy into
a different network namespace with the new command
iw phy#<idx> set netns <pid>
and all virtual interfaces will follow (or the operation fails).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connected to a BSS, or joined to an IBSS, we'll want
to know in userspace without using wireless extensions, so
report the BSS status in the BSS list. Userspace can query
the BSS list, display all the information and retrieve the
station information as well.
For example (from hwsim):
$ iw dev wlan1 scan dump
BSS 02:00:00:00:00:00 (on wlan1) -- associated
freq: 2462
beacon interval: 100
capability: ESS ShortSlotTime (0x0401)
signal: -50.00 dBm
SSID: j
Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0
DS Paramater set: channel 11
ERP: <no flags>
Extended supported rates: 24.0 36.0 48.0 54.0
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reworks the key operation in cfg80211, and now only
allows, from userspace, configuring keys (via nl80211)
after the connection has been established (in managed
mode), the IBSS been joined (in IBSS mode), at any time
(in AP[_VLAN] modes) or never for all the other modes.
In order to do shared key authentication correctly, it
is now possible to give a WEP key to the AUTH command.
To configure static WEP keys, these are given to the
CONNECT or IBSS_JOIN command directly, for a userspace
SME it is assumed it will configure it properly after
the connection has been established.
Since mac80211 used to check the default key in IBSS
mode to see whether or not the network is protected,
it needs an update in that area, as well as an update
to make use of the WEP key passed to auth() for shared
key authentication.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will soon want to nest key attributes into
some new attribute for configuring static WEP
keys at connect() and ibss_join() time, so we
need nested attributes for that. However, key
attributes right now are 'global'. This patch
thus introduces new nested attributes for the
key settings and functions for parsing them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes two small bugs:
1) the connect variable is already initialised, and the
assignment to auth_type overwrites the previous setting
with a wrong value
2) when all authentication attempts fail, we need to report
that we couldn't connect
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Potential memory leak via msg pointer in nl80211_get_key() function.
Signed-off-by: Niko Jokinen <ext-niko.k.jokinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes generic netlink network namespace aware. No
generic netlink families except for the controller family
are made namespace aware, they need to be checked one by
one and then set the family->netnsok member to true.
A new function genlmsg_multicast_netns() is introduced to
allow sending a multicast message in a given namespace,
for example when it applies to an object that lives in
that namespace, a new function genlmsg_multicast_allns()
to send a message to all network namespaces (for objects
that do not have an associated netns).
The function genlmsg_multicast() is changed to multicast
the message in just init_net, which is currently correct
for all generic netlink families since they only work in
init_net right now. Some will later want to work in all
net namespaces because they do not care about the netns
at all -- those will have to be converted to use one of
the new functions genlmsg_multicast_allns() or
genlmsg_multicast_netns() whenever they are made netns
aware in some way.
After this patch families can easily decide whether or
not they should be available in all net namespaces. Many
genl families us it for objects not related to networking
and should therefore be available in all namespaces, but
that will have to be done on a per family basis.
Note that this doesn't touch on the checkpoint/restart
problem where network namespaces could be used, genl
families and multicast groups are numbered globally and
I see no easy way of changing that, especially since it
must be possible to multicast to all network namespaces
for those families that do not care about netns.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've named the registered devices 'drv' sometimes,
thinking of "driver", which is not what it is, it's
the internal representation of a wiphy, i.e. a
device. Let's clean up the naming once and and use
'rdev' aka 'registered device' everywhere.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Over time, a lot of locking issues have crept into
the smarts of cfg80211, so e.g. scan completion can
race against a new scan, IBSS join can race against
leaving an IBSS, etc.
Introduce a new per-interface lock that protects
most of the per-interface data that we need to keep
track of, and sprinkle assertions about that lock
everywhere. Some things now need to be offloaded to
work structs so that we don't require being able to
sleep in functions the drivers call. The exception
to that are the MLME callbacks (rx_auth etc.) that
currently only mac80211 calls because it was easier
to do that there instead of in cfg80211, and future
drivers implementing those calls will, if they ever
exist, probably need to use a similar scheme like
mac80211 anyway...
In order to be able to handle _deauth and _disassoc
properly, introduce a cookie passed to it that will
determine locking requirements.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse warns about a number of things, and one of them
(use_mfp shadowed variable) actually is a bug, fix all
of them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we call that cfg80211_put_dev(), but that is
misleading. With the new convention of using 'rdev' for
registered_device variables, also call that function
cfg80211_unlock_rdev().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we don't really know that well in the kernel,
let's let the SME control whether it wants to use
reassociation or not, by allowing it to give the
previous BSSID in the associate() parameters.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In this case, only one cipher makes sense, unlike for
connect() where it may be possible to have the card or
driver select.
No changes to mac80211 due to the way the structs are
laid out -- but the loop in net/mac80211/cfg.c will
degrade to just zero or one passes.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to avoid problems with BSS structs going away
while they're in use, I've long wanted to make cfg80211
keep track of them. Without the SME, that wasn't doable
but now that we have the SME we can do this too. It can
keep track of up to four separate authentications and
one association, regardless of whether it's controlled
by the cfg80211 SME or the userspace SME.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds code to make it possible to use the cfg80211
connect() API with wireless extensions, and because the
previous patch added emulation of that API with auth()
and assoc(), by extension also supports wext on that.
At the same time, removes code from mac80211 for wext,
but doesn't yet clean up mac80211's mlme code more.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds code to cfg80211 so that drivers (mac80211 right
now) that don't implement connect but rather auth/assoc can
still be used with the nl80211 connect command. This will
also be necessary for the wext compat code.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces the cfg80211 connect/disconnect API.
The goal here is to run the AUTH and ASSOC steps in one call.
This is needed for some fullmac cards that run both steps
directly from the target, after the host driver sends a
connect command.
Additionally, all the new crypto parameters for connect()
are now also valid for associate() -- although associate
requires the IEs to be used, the information can be useful
for drivers and should be given.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This introduces a new NL80211_CMD_TESTMODE for testing
and calibration use with nl80211. There's no multiplexing
like like iwpriv had, and the command is not available by
default, it needs to be explicitly enabled in Kconfig and
shouldn't be enabled in most kernels.
The command requires a wiphy index or interface index to
identify the device to operate on, and the new TESTDATA
attribute. There also is API for sending replies to the
command, and testmode multicast messages (on a testmode
multicast group).
I've also updated mac80211 to be able to pass through the
command to the driver, since it itself doesn't implement
the testmode command.
Additionally, to give people an idea of how to use the
command, I've added a little code to hwsim that makes use
of the new command to set the powersave mode, this is
currently done via debugfs and should remain there, and
the testmode command only serves as an example of how to
use this best -- with nested netlink attributes in the
TESTDATA attribute. A hwsim testmode tool can be found at
http://git.sipsolutions.net/hwsim.git/. This tool is BSD
licensed so people can easily use it as a basis for their
own internal fabrication and validation tools.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding GFP_ATOMIC everywhere, add a
new function parameter that gets the flags from the
caller. Obviously then I need to update all callers
(all of them in mac80211), and it turns out that now
it's ok to use GFP_KERNEL in almost all places.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It isn't very useful to scan the same channel more than once
during a given scan, and some hardware (notably iwlwifi) can
only scan a limited number of channels at a time. To prevent
any overflows, simply disallow scanning any channel multiple
times in a given scan command. This is a small change in the
userspace ABI, but the only user, wpa_supplicant, never asks
for a scan with the same frequency listed twice.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To ease multiple apps working together smoothly,
send a notification when a scan is started.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there was a reason I'm passing the ifidx I cannot
remember it any more and don't see one now, so let's
just pass the pointer itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't forget to unlock cfg80211_mutex in one fail path of
nl80211_set_wiphy.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I disallowed interfering with stations on non-AP interfaces,
I not only forget mesh but also managed interfaces which need
this for the authorized flag. Let's actually validate everything
properly.
This fixes an nl80211 regression introduced by the interfering,
under which wpa_supplicant -Dnl80211 could not properly connect.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh Point interfaces can also set parameters, for example plink_open is
used to manually establish peer links from user-space (currently via
iw). Add Mesh Point to the check in nl80211_set_station.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit b2a151a288 added a check that prevents adding or deleting
stations on non-AP interfaces. Adding and deleting stations is
supported for Mesh Point interfaces, so add Mesh Point to that check as
well.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On non-AP interfaces userspace has no business interfering with
the station management, this can confuse mac80211 (and other
drivers probably wouldn't support it anyway). Allow adding and
removing stations only on AP interfaces.
(Reconcile this w/ previous version of patch posted with same
subject... -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a scan finishes only the program that asked for it
knows what kind of scan it was; let's tell everybody else
about the scan parameters as well so they can evaluate
the result of the scan better. Also helps with debugging.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have some validation code in mac80211 but said code will
force an invalid AID to 0 which isn't a valid AID either;
instead require a valid AID (1-2007) to be passed in from
userspace in cfg80211 already. Also move the code before
the race comment since it can only be executed during STA
addition and thus is not racy.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use genl_register_family_with_ops() instead of a copy.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race on access to last_request and its alpha2
through reg_is_valid_request() and us possibly processing
first another regulatory request on another CPU. We avoid
this improbably race by locking with the cfg80211_mutex as
we should have done in the first place. While at it add
the assert on locking on reg_is_valid_request().
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has no functional change, but it will make the race
fix easier to spot in my next patch.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has no functional change except we save a kfree(rd) and
allows us to clean this code up a bit after this. We do
avoid an unnecessary kfree(NULL) but calling that was OK too.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Validate RSC (NL80211_ATTR_KEY_SEQ) length in nl80211/cfg80211 instead
of having to do this in all the drivers.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thanks to nl80211 userspace can be very specific upon device
configuration. Before processing the request for the new HT40
channel types (HT40- or HT40+) we need to ensure we can use them
regulatory-wise. This wasn't required with wireless extensions as
specifying the channel type wasn't not available and configuration
was done towards the end implicitly upon association or reception
of beacons from the AP. For the new nl80211 we have to check this
when configuring the interfaces explicitly.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nlmsg_new() adds the size of the netlink header to the value
that has been passed as parameter. If NLMSG_GOODSIZE is selected,
we request an allocation of one memory page plus the size of the
header. Instead, NLMSG_DEFAULT_SIZE should be used since it
already substracts the size of the Netlink header.
I have the impression that the similar naming in both constant
is error prone when using it with nlmsg_new(). This is already
documented in include/net/netlink.h
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting a key with NL80211_CMD_NEW_KEY, we should allow the key
sequence number (RSC) to be set in order to allow replay protection to
work correctly for group keys. This patch documents this use for
nl80211 and adds the couple of missing pieces in nl80211/cfg80211 and
mac80211 to support this. In addition, WEXT SIOCSIWENCODEEXT compat
processing in cfg80211 is extended to handle the RSC (this was already
specified in WEXT, but just not implemented in cfg80211/mac80211).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new NL80211_ATTR_CONTROL_PORT flag for NL80211_CMD_ASSOCIATE to
allow user space to indicate that it will control the IEEE 802.1X port
in station mode. Previously, mac80211 was always marking the port
authorized in station mode. This was enough when drop_unencrypted flag
was set. However, drop_unencrypted can currently be controlled only
with WEXT and the current nl80211 design does not allow fully secure
configuration. Fix this by providing a mechanism for user space to
control the IEEE 802.1X port in station mode (i.e., do the same that
we are already doing in AP mode).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is currently not possible to modify station flags, but that
capability would be very useful. This patch introduces a new
nl80211 attribute that contains a set/mask for station flags,
and updates the internal API (and mac80211) to mirror that.
The new attribute is parsed before falling back to the old so
that userspace can specify both (if it can) to work on all
kernels.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_STA_FLAG_MFP was forgotten from sta_flags_policy. The previous
version added the flag due to the loop used in parse_station_flags,
but the proper behavior would be to allow nla_parse_nested() to go
through the policy for all flags.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move key handling wireless extension ioctls from mac80211 to cfg80211
so that all drivers that implement the cfg80211 operations get wext
compatibility.
Note that this drops the SIOCGIWENCODE ioctl support for getting
IW_ENCODE_RESTRICTED/IW_ENCODE_OPEN. This means that iwconfig will
no longer report "Security mode:open" or "Security mode:restricted"
for mac80211. However, what we displayed there (the authentication
algo used) was actually wrong -- linux/wireless.h states that this
setting is meant to differentiate between "Refuse non-encoded packets"
and "Accept non-encoded packets".
(Combined with "cfg80211: fix a couple of bugs with key ioctls". -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On non-AP interfaces userspace has no business interfering with
the station management, this can confuse mac80211 (and other
drivers probably wouldn't support it anyway). Allow adding and
removing stations only on AP interfaces.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_CMD_ASSOCIATE request must be able to indicate whether
management frame protection (IEEE 802.11w) is being used. mac80211 was
able to use MFP in client mode only with WEXT, but the new
NL80211_ATTR_USE_MFP attribute will allow this to be done with
nl80211, too.
Since we are currently using nl80211 for MFP only with drivers that
use user space SME, only MFP disabled and required values are
used. However, the NL80211_ATTR_USE_MFP attribute is an enum that can
be extended with MFP optional in the future, if that is needed with
some drivers (e.g., if the RSN IE is generated by the driver).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes sparse complaint:
CHECK net/wireless/nl80211.c
net/wireless/nl80211.c:3694:6:
warning: symbol 'nl80211_send_mlme_timeout'
was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SME needs to be notified when the authentication or association
attempt times out and MLME has stopped processing in order to allow
the SME to decide what to do next.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the JOIN_IBSS command look at the beacon interval
attribute to see if the user requested a specific beacon
interval, if not default to 100 TU (wext too).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we leave an IBSS, we should clear the SSID and not just the
BSSID, but since WEXT allows configuring while the interface is
down we must not clear it when leaving due to taking the iface
down, so some complications are needed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new nl80211 attributes that can be used with NL80211_CMD_SET_WIPHY
and NL80211_CMD_GET_WIPHY to manage fragmentation/RTS threshold and
retry limits.
Since these values are stored in struct wiphy, remove the local copy
from mac80211 where feasible (frag & rts threshold). The retry limits
are currently needed in struct ieee80211_conf, but these could be
eventually removed since the driver should have access to the values
in struct wiphy.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds IBSS API along with (preliminary) wext handlers.
The wext handlers can only do IBSS so you need to call them
from your own wext handlers if the mode is IBSS.
The nl80211 API requires
* an SSID
* a channel (frequency) for the case that a new IBSS
has to be created
It optionally supports
* a flag to fix the channel
* a fixed BSSID
The cfg80211 code also takes care to leave the IBSS before
the netdev is set down. If wireless extensions are used, it
also caches values when the interface is down and instructs
the driver to join when the interface is set up.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When listing all wireless netdevs in the system this
is useful to print which wiphy they belong to. Just
add the attribute, any program that doesn't care will
just ignore it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the necessary code and fields to let drivers specify
their cipher capabilities and exports them to userspace. Also
update mac80211 to export the ciphers it has.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This informs userspace when a change has occured on a world
roaming wiphy's channel which has lifted some restrictions
due to a regulatory beacon hint.
Because this is now sent to userspace through the regulatory
multicast group we remove the debug prints we used to use as
they are no longer necessary.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a netlink channel put helper, nl80211_msg_put_channel(),
which we will also make use of later for the beacon hints events.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of just passing the cfg80211-requested IEs, pass
the locally generated ones as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a new attribute for a wiphy that tells
userspace how long the information elements added to a probe
request frame can be at most. It also updates the at76 to
advertise that it cannot support that, and, for now until I
can fix that, iwlwifi too.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Define a new nl80211 event, NL80211_CMD_MICHAEL_MIC_FAILURE, to be
used to notify user space about locally detected Michael MIC failures.
This matches with the MLME-MICHAELMICFAILURE.indication() primitive.
Since we do not actually have TSC in the skb anymore when
mac80211_ev_michael_mic_failure() is called, that function is changed
to take in the TSC as an optional parameter instead of as a
requirement to include the TSC after the hdr field (which we did not
really follow). For now, TSC is not included in the events from
mac80211, but it could be added at some point.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, nl80211 mlme events were generated only for received
deauthentication and disassociation frames. We need to do the same for
locally generated ones in order to let applications know that we
disconnected (e.g., when AP does not reply to a probe). Rename the
nl80211 and cfg80211 functions (s/rx_//) to make it clearer that they
are used for both received and locally generated frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_ATTR_AUTH_TYPE is a required parameter for
NL80211_CMD_AUTHENTICATE. We are currently (by chance) defaulting to
open system authentication if the attribute is not specified. It is
better to just reject the invalid command.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes nl80211 to:
* validate that any IE input is a valid IE (stream)
* move some validation code before locking
* require that a reason code is given for both deauth/disassoc
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One of the code paths sending deauth/disassoc events ends up calling
this function with rcu_read_lock held, so we must use GFP_ATOMIC in
allocation routines.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis reports that there's a circular locking dependency;
this is because cfg80211_dev_rename() will acquire the
cfg80211_mutex while the device mutex is held, while
this normally is done the other way around. The solution
is to open-code the device-getting in nl80211_set_wiphy
and require holding the mutex around cfg80211_dev_rename
rather than acquiring it within.
Also fix a bug -- rtnl locking is expected by drivers so
we need to provide it.
Reported-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When somebody tries to set the interface mode to the existing
mode, don't ask the driver but silently accept the setting.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not want to require all the drivers using cfg80211 to need to do
this. In addition, make the error values consistent by using
EOPNOTSUPP instead of semi-random assortment of errno values.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not want to require all the drivers using cfg80211 to need to do
this or to be prepared to handle these commands when the interface is
down.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check that the used authentication type and reason code are valid here
so that drivers/mac80211 do not need to care about this. In addition,
remove the unnecessary validation of SSID attribute length which is
taken care of by netlink policy.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functionality that NL80211_CMD_SET_MGMT_EXTRA_IE provided can now
be achieved with cleaner design by adding IE(s) into
NL80211_CMD_TRIGGER_SCAN, NL80211_CMD_AUTHENTICATE,
NL80211_CMD_ASSOCIATE, NL80211_CMD_DEAUTHENTICATE, and
NL80211_CMD_DISASSOCIATE.
Since this is a very recently added command and there are no known (or
known planned) applications using NL80211_CMD_SET_MGMT_EXTRA_IE and
taken into account how much extra complexity it adds to the IE
processing we have now (and need to add in the future to fix IE order
in couple of frames), it looks like the best option is to just remove
the implementation of this command for now. The enum values themselves
are left to avoid changing the nl80211 command or attribute numbers.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds new nl80211 commands to allow user space to request
authentication and association (and also deauthentication and
disassociation). The commands are structured to allow separate
authentication and association steps, i.e., the interface between
kernel and user space is similar to the MLME SAP interface in IEEE
802.11 standard and an user space application takes the role of the
SME.
The patch introduces MLME-AUTHENTICATE.request,
MLME-{,RE}ASSOCIATE.request, MLME-DEAUTHENTICATE.request, and
MLME-DISASSOCIATE.request primitives. The authentication and
association commands request the actual operations in two steps
(assuming the driver supports this; if not, separate authentication
step is skipped; this could end up being a separate "connect"
command).
The initial implementation for mac80211 uses the current
net/mac80211/mlme.c for actual sending and processing of management
frames and the new nl80211 commands will just stop the current state
machine from moving automatically from authentication to association.
Future cleanup may move more of the MLME operations into cfg80211.
The goal of this design is to provide more control of authentication and
association process to user space without having to move the full MLME
implementation. This should be enough to allow IEEE 802.11r FT protocol
and 802.11s SAE authentication to be implemented. Obviously, this will
also bring the extra benefit of not having to use WEXT for association
requests with mac80211. An example implementation of a user space SME
using the new nl80211 commands is available for wpa_supplicant.
This patch is enough to get IEEE 802.11r FT protocol working with
over-the-air mechanism (over-the-DS will need additional MLME
primitives for handling the FT Action frames).
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new nl80211 event notifications (and a new multicast group, "mlme")
for informing user space about received and processed Authentication,
(Re)Association Response, Deauthentication, and Disassociation frames in
station and IBSS modes (i.e., MLME SAP interface primitives
MLME-AUTHENTICATE.confirm, MLME-ASSOCIATE.confirm,
MLME-REASSOCIATE.confirm, MLME-DEAUTHENTICATE.indicate, and
MLME-DISASSOCIATE.indication). The event data is encapsulated as the 802.11
management frame since we already have the frame in that format and it
includes all the needed information.
This is the initial step in providing MLME SAP interface for
authentication and association with nl80211. In other words, kernel code
will act as the MLME and a user space application can control it as the
SME.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I added scanning to cfg80211, we got a lock dependency like this:
rtnl --> cfg80211_mtx
nl80211, on the other hand, has the reverse lock dependency:
cfg80211_mtx --> rtnl
which clearly is a bad idea. This patch reworks nl80211 to take these
two locks in the other order to fix the possible, and easily
triggerable, deadlock.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes nl80211 export the supported commands (command groups)
per wiphy so userspace has an idea what it can do -- this will be
required reading for userspace when we introduce auth/assoc /or/
connect for older hardware that cannot separate auth and assoc.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_CMD_GET_MESH_PARAMS and NL80211_CMD_SET_MESH_PARAMS handlers
did not verify whether a function pointer is NULL (not supported by
the driver) before trying to call the function. The former nl80211
command is available for unprivileged users, too, so this can
potentially allow normal users to kill networking (or worse..) if
mac80211 is built without CONFIG_MAC80211_MESH=y.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows us to send to userspace "regulatory" events.
For now we just send an event when we change regulatory domains.
We also notify userspace when devices are using their own custom
world roaming regulatory domains.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"cfg80211: add assert_cfg80211_lock() to ensure proper protection"
added assert_cfg80211_lock() calls into various places. At least
one of them, nl80211_send_wiphy(), should not have been there. That
triggers the BUG_ON in assert_cfg80211_lock() and pretty much kills
the kernel whenever someone runs hostapd.. Remove that call and make
assert_cfg80211_lock() use WARN_ON instead of BUG_ON to be a bit more
friendly to users.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All regulatory hints (core, driver, userspace and 11d) are now processed in
a workqueue.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If cfg80211 is built into the kernel there is perhaps a small
time window betwen nl80211_init() and regulatory_init() where
cfg80211_regdomain hasn't yet been initialized to let the
wireless core do its work. During that rare case and time
frame (if its even possible) we don't allow user regulatory
changes as cfg80211 is working on enabling its first regulatory
domain.
To check for cfg80211_regdomain we now contend the entire operation
using the cfg80211_mutex.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_drv_mutex is protecting more than the driver list,
this renames it and documents what its currently supposed to
protect.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Makes it clearer to read when comparing to ifidx
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It wasn't a good idea to make the signal type a per-BSS option,
although then it is closer to the actual value. Move it to be
a per-wiphy setting, update mac80211 to match.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no particular reason to not let untrusted users see
this information -- it's just the stations we're talking to,
packet counters for them and possibly some mesh things.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX/RX packet counters are needed to fill in RADIUS Accounting
attributes Acct-Output-Packets and Acct-Input-Packets. We already
collect the needed information, but only the TX/RX bytes were
previously exposed through nl80211. Allow applications to fetch the
packet counters, too, to provide more complete support for accounting.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This extends the NL80211_CMD_TRIGGER_SCAN command to allow applications
to specify a set of information element(s) to be added into Probe
Request frames with NL80211_ATTR_IE. This provides support for the
MLME-SCAN.request primitive parameter VendorSpecificInfo and can be
used, e.g., to implement WPS scanning.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds basic scan capability to cfg80211/nl80211 and
changes mac80211 to use it. The BSS list that cfg80211 maintains
is made driver-accessible with a private area in each BSS struct,
but mac80211 doesn't yet use it. That's another large project.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lets userspace request to get the currently set
regulatory domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the regulatory domain is already set it is technically not an error
so do not pass an errno to userspace.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A new nl80211 command, NL80211_CMD_SET_MGMT_EXTRA_IE, can be used to
add arbitrary IE data into the end of management frames. The interface
allows extra IEs to be configured for each management frame subtype, but
only some of them (ProbeReq, ProbeResp, Auth, (Re)AssocReq, Deauth,
Disassoc) are currently accepted in mac80211 implementation.
This makes it easier to implement IEEE 802.11 extensions like WPS and
FT that add IE(s) into some management frames. In addition, this can
be useful for testing and experimentation purposes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add mechanism for managing BIP keys (IGTK) and integrate BIP into the
TX/RX paths.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HT management is done differently for AP and STA modes, unify
to just the ->config() callback since HT is fundamentally a
PHY property and cannot be per-BSS.
Rename enum nl80211_sec_chan_offset as nl80211_channel_type to denote
the channel type ( NO_HT, HT20, HT40+, HT40- ).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds signal strength and transmission bitrate
to the station_info of nl80211.
Signed-off-by: Henning Rogge <rogge@fgan.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix two small bugs with HT frequency setting:
* HT is accepted even when the driver is incapable
* HT40 is accepted when the driver cannot do 40 MHz
(both on the selected band)
Also simplify the code a little.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds new NL80211_CMD_SET_WIPHY attributes
NL80211_ATTR_WIPHY_FREQ and NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET to allow
userspace to set the operating channel (e.g., hostapd for AP mode).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to be consistent with NL80211_ATTR_POWER_RULE_MAX_EIRP,
change NL80211_FREQUENCY_ATTR_MAX_TX_POWER to use mBm and U32 instead
of dBm and U8. This is a userspace interface change, but the previous
version had not yet been pushed upstream and there are no userspace
programs using this yet, so there is justification to get this change in
as long as it goes in before the previous version gets out.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is useful information to provide for userspace (e.g., hostapd needs
this to generate Country IE).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds country IE parsing to mac80211 and enables its usage
within the new regulatory infrastructure in cfg80211. We parse
the country IEs only on management beacons for the BSSID you are
associated to and disregard the IEs when the country and environment
(indoor, outdoor, any) matches the already processed country IE.
To avoid following misinformed or outdated APs we build and use
a regulatory domain out of the intersection between what the AP
provides us on the country IE and what CRDA is aware is allowed
on the same country.
A secondary device is allowed to follow only the same country IE
as it make no sense for two devices on a system to be in two
different countries.
In the case the AP is using country IEs for an incorrect country
the user may help compliance further by setting the regulatory
domain before or after the IE is parsed and in that case another
intersection will be performed.
CONFIG_WIRELESS_OLD_REGULATORY is supported but requires CRDA
present.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new attribute, NL80211_ATTR_WIPHY_TXQ_PARAMS, that can be used with
NL80211_CMD_SET_WIPHY for userspace (e.g., hostapd) to set TX queue
parameters (txop, cwmin, cwmax, aifs).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new attribute, NL80211_ATTR_BSS_BASIC_RATES, that can be used with
NL80211_CMD_SET_BSS for userspace (e.g., hostapd) to set which rates are
in the basic rate set.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code needs to be split out and cleaned up, so as a
first step remove the capability, to add it back in a
subsequent patch as a separate function. Also remove the
publically facing return value of the function and the
wiphy argument. A number of internal functions go from
being generic helpers to just being used for alpha2
setting.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The regdom struct is given to the core, so it might as well
free it in error conditions.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The two new commands are NL80211_CMD_GET_MESH_PARAMS and
NL80211_CMD_SET_MESH_PARAMS. There is a new attribute enum,
NL80211_ATTR_MESH_PARAMS, which enumerates the various mesh configuration
parameters.
Moved struct mesh_config from mac80211/ieee80211_i.h to net/cfg80211.h.
nl80211_get_mesh_params and nl80211_set_mesh_params unpack the netlink messages
and ask the driver to get or set the configuration. This is done via two new
function stubs, get_mesh_params and set_mesh_params, in struct cfg80211_ops.
Signed-off-by: Colin McCabe <colin@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NLA_NESTED attributes cannot be empty, but we want to be able to
specify "no flags" (empty attribute) vs. "no change" (no attribute).
Therefore, remove the NLA_NESTED policy so it can work as an empty
attribute.
I guess I should have used a u32 for these flags instead, but we're
stuck with it now. Haven't noticed earlier because of a bug in iw...
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This exports the local HT capabilities in nl80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reject configuring mesh-id for non-mesh, monitor flags for non-monitor.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes cfg80211 show the interface in the nl80211
information about a specific interface. API users are required
to keep the type updated (everything else is fairly complicated)
but you will get a warning if you fail to keep it updated.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the new wireless regulatory infrastructure. The
main motiviation behind this was to centralize regulatory
code as each driver was implementing their own regulatory solution,
and to replace the initial centralized code we have where:
* only 3 regulatory domains are supported: US, JP and EU
* regulatory domains can only be changed through module parameter
* all rules were built statically in the kernel
We now have support for regulatory domains for many countries
and regulatory domains are now queried through a userspace agent
through udev allowing distributions to update regulatory rules
without updating the kernel.
Each driver can regulatory_hint() a regulatory domain
based on either their EEPROM mapped regulatory domain value to a
respective ISO/IEC 3166-1 country code or pass an internally built
regulatory domain. We also add support to let the user set the
regulatory domain through userspace in case of faulty EEPROMs to
further help compliance.
Support for world roaming will be added soon for cards capable of
this.
For more information see:
http://wireless.kernel.org/en/developers/Regulatory/CRDA
For now we leave an option to enable the old module parameter,
ieee80211_regdom, and to build the 3 old regdomains statically
(US, JP and EU). This option is CONFIG_WIRELESS_OLD_REGULATORY.
These old static definitions and the module parameter is being
scheduled for removal for 2.6.29. Note that if you use this
you won't make use of a world regulatory domain as its pointless.
If you leave this option enabled and if CRDA is present and you
use US or JP we will try to ask CRDA to update us a regulatory
domain for us.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is obviously good for userspace to know up front which
interface modes a given piece of hardware might support (even
if adding such an interface might fail later because of
concurrency issues), so let's make cfg80211 aware of that.
For good measure, disallow adding interfaces in all other
modes so drivers don't forget to announce support for one mode
when they add it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace (e.g., hostapd) to set HT capabilities for associated
STAs. This is based on a patch from Zhu Yi <yi.zhu@intel.com> (only
the NL80211_ATTR_HT_CAPABILITY for NEW_STA part is included here).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change adds a new cfg80211 command, NL80211_CMD_SET_BSS, to allow
AP mode BSS parameters to be changed from user space (e.g., hostapd).
The drivers using mac80211 are expected to be modified with separate
changes to use the new BSS info parameter for short slot time in the
bss_info_changed() handler.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julius Volz pointed out that the dump callbacks in nl80211 were
broken and fixed one of them. This patch fixes the other three
and also addresses the TODOs there.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Julius Volz <juliusv@google.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although I only tested similar code (I don't use any of this wireless
code), the state maintainance between Netlink dump callback invocations
seems wrong here and should lead to an endless loop. There are also other
examples in the same file which might have the same problem. Perhaps someone
can actually test this (or refute my logic).
Take the simple example with only one element in the list (which should fit
into the message):
1. invocation:
Start:
idx = 0, start = 0
Loop:
condition (++idx < start) => (1 < 0) => false
=> no continue, fill one entry, exit loop, return skb->len > 0
2. invocation:
Start:
idx = 0, start = 1
Loop:
condition (++idx < start) => (1 < 1) => false
=> no continue, fill the same entry again, exit loop, return skb->len > 0
3. invocation:
Same as 2. invocation, endless invocation of callback.
Also, iterations where the filling of an element fails should not be counted as
completed, so idx should not be incremented in this case.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make nlmsg_trim(), nlmsg_cancel(), genlmsg_cancel(), and
nla_nest_cancel() void functions.
Return -EMSGSIZE instead of -1 if the provided message buffer is not
big enough.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the STA AID setting and actually makes hostapd/mac80211
work properly in presence of power-saving stations.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added support for mesh id and mesh path operation as well as
station structure dumping.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows precise control over what a monitor interface shows.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes nl80211 export the hardware bitrate/channel capabilities
as registered in a wiphy.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After a station is added to the kernel's structures, userspace
has to be able to retrieve statistics about that station, especially
whether the station was idle and how much bytes were transferred
to and from it. This adds the necessary code to nl80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds station handling to cfg80211/nl80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the necessary API to cfg80211/nl80211 to allow
changing beaconing settings.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces key handling to cfg80211/nl80211. Default
and group keys can be added, changed and removed; sequence
counters for each key can be retrieved.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg