When TCP Small Queues was added, we used a sysctl to limit amount of
packets queues on Qdisc/device queues for a given TCP flow.
Problem is this limit is either too big for low rates, or too small
for high rates.
Now TCP stack has rate estimation in sk->sk_pacing_rate, and TSO
auto sizing, it can better control number of packets in Qdisc/device
queues.
New limit is two packets or at least 1 to 2 ms worth of packets.
Low rates flows benefit from this patch by having even smaller
number of packets in queues, allowing for faster recovery,
better RTT estimations.
High rates flows benefit from this patch by allowing more than 2 packets
in flight as we had reports this was a limiting factor to reach line
rate. [ In particular if TX completion is delayed because of coalescing
parameters ]
Example for a single flow on 10Gbp link controlled by FQ/pacing
14 packets in flight instead of 2
$ tc -s -d qd
qdisc fq 8001: dev eth0 root refcnt 32 limit 10000p flow_limit 100p
buckets 1024 quantum 3028 initial_quantum 15140
Sent 1168459366606 bytes 771822841 pkt (dropped 0, overlimits 0
requeues 6822476)
rate 9346Mbit 771713pps backlog 953820b 14p requeues 6822476
2047 flow, 2046 inactive, 1 throttled, delay 15673 ns
2372 gc, 0 highprio, 0 retrans, 9739249 throttled, 0 flows_plimit
Note that sk_pacing_rate is currently set to twice the actual rate, but
this might be refined in the future when a flow is in congestion
avoidance.
Additional change : skb->destructor should be set to tcp_wfree().
A future patch (for linux 3.13+) might remove tcp_limit_output_bytes
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few small fixes:
1) Make sure that debugfs entries are removed early enough to prevent
a race.
2) Drop a stray regulator_put from ad8366 left over from the devm_ patches.
3) The ST magnetometer driver had incorrect register addresses for the
actual data channels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)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=c+WH
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.12b2' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 3.12 cycle (take 2)
A few small fixes:
1) Make sure that debugfs entries are removed early enough to prevent
a race.
2) Drop a stray regulator_put from ad8366 left over from the devm_ patches.
3) The ST magnetometer driver had incorrect register addresses for the
actual data channels.
Commit f95499c303,
n_tty: Don't wait for buffer work in read() loop
creates a race window which can cause a pty master read()
to miss the last pty slave write(s) and return -EIO instead,
thus signalling the pty slave is closed. This can happen when
the pty slave is written and immediately closed but before the
tty buffer i/o loop receives the new input; the pty master
read() is scheduled, sees its read buffer is empty and the
pty slave has been closed, and exits.
Because tty_flush_to_ldisc() has significant performance impact
for parallel i/o, rather than revert the commit, special case this
condition (ie., when the read buffer is empty and the 'other' pty
has been closed) and, only then, wait for buffer work to complete
before re-testing if the read buffer is still empty.
As before, subsequent pty master reads return any available data
until no more data is available, and then returns -EIO to
indicate the pty slave has closed.
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi,
my Huawei 3G modem has an embedded Smart Card reader which causes
trouble when the modem is being detected (a bunch of "<warn> (ttyUSBx):
open blocked by driver for more than 7 seconds!" in messages.log). This
trivial patch corrects the problem for me. The modem identifies itself
as "12d1:1406 Huawei Technologies Co., Ltd. E1750" in lsusb although the
description on the body says "Model E173u-1"
Signed-off-by: Michal Malý <madcatxster@prifuk.cz>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When 5e12a613 and 0cd3754a were introduced, Netgear ReadyNAS 102 .dts
file was queued for inclusion and missed the update to have Mbus (and
then BootROM) ranges properties declared. It also missed the relocation
of Armada 370/XP PCIe DT nodes introduced by 14fd8ed0 after de1af8d4.
This patch fixes that which makes 3.12-rc3 bootable on the NAS.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
- Stable fix for Oopses in the pNFS files layout driver
- Fix a regression when doing a non-exclusive file create on NFSv4.x
- NFSv4.1 security negotiation fixes when looking up the root filesystem
- Fix a memory ordering issue in the pNFS files layout driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=ScfI
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.12-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Stable fix for Oopses in the pNFS files layout driver
- Fix a regression when doing a non-exclusive file create on NFSv4.x
- NFSv4.1 security negotiation fixes when looking up the root
filesystem
- Fix a memory ordering issue in the pNFS files layout driver
* tag 'nfs-for-3.12-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Give "flavor" an initial value to fix a compile warning
NFSv4.1: try SECINFO_NO_NAME flavs until one works
NFSv4.1: Ensure memory ordering between nfs4_ds_connect and nfs4_fl_prepare_ds
NFSv4.1: nfs4_fl_prepare_ds - fix bugs when the connect attempt fails
NFSv4: Honour the 'opened' parameter in the atomic_open() filesystem method
Pass-all-multicast is controlled by bit 3 in RX control, not bit 2
(pass undersized frames).
Reported-by: Joseph Chang <joseph_chang@davicom.com.tw>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
pidns: fix free_pid() to handle the first fork failure
ipc,msg: prevent race with rmid in msgsnd,msgrcv
ipc/sem.c: update sem_otime for all operations
mm/hwpoison: fix the lack of one reference count against poisoned page
mm/hwpoison: fix false report on 2nd attempt at page recovery
mm/hwpoison: fix test for a transparent huge page
mm/hwpoison: fix traversal of hugetlbfs pages to avoid printk flood
block: change config option name for cmdline partition parsing
mm/mlock.c: prevent walking off the end of a pagetable in no-pmd configuration
mm: avoid reinserting isolated balloon pages into LRU lists
arch/parisc/mm/fault.c: fix uninitialized variable usage
include/asm-generic/vtime.h: avoid zero-length file
nilfs2: fix issue with race condition of competition between segments for dirty blocks
Documentation/kernel-parameters.txt: replace kernelcore with Movable
mm/bounce.c: fix a regression where MS_SNAP_STABLE (stable pages snapshotting) was ignored
kernel/kmod.c: check for NULL in call_usermodehelper_exec()
ipc/sem.c: synchronize the proc interface
ipc/sem.c: optimize sem_lock()
ipc/sem.c: fix race in sem_lock()
mm/compaction.c: periodically schedule when freeing pages
...
"case 0" in free_pid() assumes that disable_pid_allocation() should
clear PIDNS_HASH_ADDING before the last pid goes away.
However this doesn't happen if the first fork() fails to create the
child reaper which should call disable_pid_allocation().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a race in both msgrcv() and msgsnd() between finding the msg
and actually dealing with the queue, as another thread can delete shmid
underneath us if we are preempted before acquiring the
kern_ipc_perm.lock.
Manfred illustrates this nicely:
Assume a preemptible kernel that is preempted just after
msq = msq_obtain_object_check(ns, msqid)
in do_msgrcv(). The only lock that is held is rcu_read_lock().
Now the other thread processes IPC_RMID. When the first task is
resumed, then it will happily wait for messages on a deleted queue.
Fix this by checking for if the queue has been deleted after taking the
lock.
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Reported-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: <stable@vger.kernel.org> [3.11]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit 0a2b9d4c79 ("ipc/sem.c: move wake_up_process out of the
spinlock section"), the update of semaphore's sem_otime(last semop time)
was moved to one central position (do_smart_update).
But since do_smart_update() is only called for operations that modify
the array, this means that wait-for-zero semops do not update sem_otime
anymore.
The fix is simple:
Non-alter operations must update sem_otime.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Reported-by: Jia He <jiakernel@gmail.com>
Tested-by: Jia He <jiakernel@gmail.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Mike Galbraith <efault@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lack of one reference count against poisoned page for hwpoison_inject
w/o hwpoison_filter enabled result in hwpoison detect -1 users still
referenced the page, however, the number should be 0 except the poison
handler held one after successfully unmap. This patch fix it by hold one
referenced count against poisoned page for hwpoison_inject w/ and w/o
hwpoison_filter enabled.
Before patch:
[ 71.902112] Injecting memory failure at pfn 224706
[ 71.902137] MCE 0x224706: dirty LRU page recovery: Failed
[ 71.902138] MCE 0x224706: dirty LRU page still referenced by -1 users
After patch:
[ 94.710860] Injecting memory failure at pfn 215b68
[ 94.710885] MCE 0x215b68: dirty LRU page recovery: Recovered
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the page is poisoned by software injection w/ MF_COUNT_INCREASED
flag, there is a false report during the 2nd attempt at page recovery
which is not truthful.
This patch fixes it by reporting the first attempt to try free buddy
page recovery if MF_COUNT_INCREASED is set.
Before patch:
[ 346.332041] Injecting memory failure at pfn 200010
[ 346.332189] MCE 0x200010: free buddy, 2nd try page recovery: Delayed
After patch:
[ 297.742600] Injecting memory failure at pfn 200010
[ 297.742941] MCE 0x200010: free buddy page recovery: Delayed
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PageTransHuge() can't guarantee the page is a transparent huge page
since it returns true for both transparent huge and hugetlbfs pages.
This patch fixes it by checking the page is also !hugetlbfs page.
Before patch:
[ 121.571128] Injecting memory failure at pfn 23a200
[ 121.571141] MCE 0x23a200: huge page recovery: Delayed
[ 140.355100] MCE: Memory failure is now running on 0x23a200
After patch:
[ 94.290793] Injecting memory failure at pfn 23a000
[ 94.290800] MCE 0x23a000: huge page recovery: Delayed
[ 105.722303] MCE: Software-unpoisoned page 0x23a000
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
madvise_hwpoison won't check if the page is small page or huge page and
traverses in small page granularity against the range unconditionally,
which result in a printk flood "MCE xxx: already hardware poisoned" if
the page is a huge page.
This patch fixes it by using compound_order(compound_head(page)) for
huge page iterator.
Testcase:
#define _GNU_SOURCE
#include <stdlib.h>
#include <stdio.h>
#include <sys/mman.h>
#include <unistd.h>
#include <fcntl.h>
#include <sys/types.h>
#include <errno.h>
#define PAGES_TO_TEST 3
#define PAGE_SIZE 4096 * 512
int main(void)
{
char *mem;
int i;
mem = mmap(NULL, PAGES_TO_TEST * PAGE_SIZE,
PROT_READ | PROT_WRITE, MAP_PRIVATE | MAP_ANONYMOUS | MAP_HUGETLB, 0, 0);
if (madvise(mem, PAGES_TO_TEST * PAGE_SIZE, MADV_HWPOISON) == -1)
return -1;
munmap(mem, PAGES_TO_TEST * PAGE_SIZE);
return 0;
}
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently commit bab55417b1 ("block: support embedded device command
line partition") introduced CONFIG_CMDLINE_PARSER. However, that name
is too generic and sounds like it enables/disables generic kernel boot
arg processing, when it really is block specific.
Before this option becomes a part of a full/final release, add the BLK_
prefix to it so that it is clear in absence of any other context that it
is block specific.
In addition, fix up the following less critical items:
- help text was not really at all helpful.
- index file for Documentation was not updated
- add the new arg to Documentation/kernel-parameters.txt
- clarify wording in source comments
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Cai Zhiyong <caizhiyong@huawei.com>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function __munlock_pagevec_fill() introduced in commit 7a8010cd36
("mm: munlock: manual pte walk in fast path instead of
follow_page_mask()") uses pmd_addr_end() for restricting its operation
within current page table.
This is insufficient on architectures/configurations where pmd is folded
and pmd_addr_end() just returns the end of the full range to be walked.
In this case, it allows pte++ to walk off the end of a page table
resulting in unpredictable behaviour.
This patch fixes the function by using pgd_addr_end() and pud_addr_end()
before pmd_addr_end(), which will yield correct page table boundary on
all configurations. This is similar to what existing page walkers do
when walking each level of the page table.
Additionaly, the patch clarifies a comment for get_locked_pte() call in the
function.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Bob Liu <bob.liu@oracle.com>
Cc: Jörn Engel <joern@logfs.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michel Lespinasse <walken@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The FAULT_FLAG_WRITE flag has been set based on uninitialized variable.
Fixes a regression added by commit 759496ba64 ("arch: mm: pass
userspace fault flag to generic fault handler")
Signed-off-by: Felipe Pena <felipensp@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
patch(1) can't handle zero-length files - it appears to simply not create
the file, so my powerpc build fails.
Put something in here to make life easier.
Cc: Hugh Dickins <hughd@google.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many NILFS2 users were reported about strange file system corruption
(for example):
NILFS: bad btree node (blocknr=185027): level = 0, flags = 0x0, nchildren = 768
NILFS error (device sda4): nilfs_bmap_last_key: broken bmap (inode number=11540)
But such error messages are consequence of file system's issue that takes
place more earlier. Fortunately, Jerome Poulin <jeromepoulin@gmail.com>
and Anton Eliasson <devel@antoneliasson.se> were reported about another
issue not so recently. These reports describe the issue with segctor
thread's crash:
BUG: unable to handle kernel paging request at 0000000000004c83
IP: nilfs_end_page_io+0x12/0xd0 [nilfs2]
Call Trace:
nilfs_segctor_do_construct+0xf25/0x1b20 [nilfs2]
nilfs_segctor_construct+0x17b/0x290 [nilfs2]
nilfs_segctor_thread+0x122/0x3b0 [nilfs2]
kthread+0xc0/0xd0
ret_from_fork+0x7c/0xb0
These two issues have one reason. This reason can raise third issue
too. Third issue results in hanging of segctor thread with eating of
100% CPU.
REPRODUCING PATH:
One of the possible way or the issue reproducing was described by
Jermoe me Poulin <jeromepoulin@gmail.com>:
1. init S to get to single user mode.
2. sysrq+E to make sure only my shell is running
3. start network-manager to get my wifi connection up
4. login as root and launch "screen"
5. cd /boot/log/nilfs which is a ext3 mount point and can log when NILFS dies.
6. lscp | xz -9e > lscp.txt.xz
7. mount my snapshot using mount -o cp=3360839,ro /dev/vgUbuntu/root /mnt/nilfs
8. start a screen to dump /proc/kmsg to text file since rsyslog is killed
9. start a screen and launch strace -f -o find-cat.log -t find
/mnt/nilfs -type f -exec cat {} > /dev/null \;
10. start a screen and launch strace -f -o apt-get.log -t apt-get update
11. launch the last command again as it did not crash the first time
12. apt-get crashes
13. ps aux > ps-aux-crashed.log
13. sysrq+W
14. sysrq+E wait for everything to terminate
15. sysrq+SUSB
Simplified way of the issue reproducing is starting kernel compilation
task and "apt-get update" in parallel.
REPRODUCIBILITY:
The issue is reproduced not stable [60% - 80%]. It is very important to
have proper environment for the issue reproducing. The critical
conditions for successful reproducing:
(1) It should have big modified file by mmap() way.
(2) This file should have the count of dirty blocks are greater that
several segments in size (for example, two or three) from time to time
during processing.
(3) It should be intensive background activity of files modification
in another thread.
INVESTIGATION:
First of all, it is possible to see that the reason of crash is not valid
page address:
NILFS [nilfs_segctor_complete_write]:2100 bh->b_count 0, bh->b_blocknr 13895680, bh->b_size 13897727, bh->b_page 0000000000001a82
NILFS [nilfs_segctor_complete_write]:2101 segbuf->sb_segnum 6783
Moreover, value of b_page (0x1a82) is 6786. This value looks like segment
number. And b_blocknr with b_size values look like block numbers. So,
buffer_head's pointer points on not proper address value.
Detailed investigation of the issue is discovered such picture:
[-----------------------------SEGMENT 6783-------------------------------]
NILFS [nilfs_segctor_do_construct]:2310 nilfs_segctor_begin_construction
NILFS [nilfs_segctor_do_construct]:2321 nilfs_segctor_collect
NILFS [nilfs_segctor_do_construct]:2336 nilfs_segctor_assign
NILFS [nilfs_segctor_do_construct]:2367 nilfs_segctor_update_segusage
NILFS [nilfs_segctor_do_construct]:2371 nilfs_segctor_prepare_write
NILFS [nilfs_segctor_do_construct]:2376 nilfs_add_checksums_on_logs
NILFS [nilfs_segctor_do_construct]:2381 nilfs_segctor_write
NILFS [nilfs_segbuf_submit_bio]:464 bio->bi_sector 111149024, segbuf->sb_segnum 6783
[-----------------------------SEGMENT 6784-------------------------------]
NILFS [nilfs_segctor_do_construct]:2310 nilfs_segctor_begin_construction
NILFS [nilfs_segctor_do_construct]:2321 nilfs_segctor_collect
NILFS [nilfs_lookup_dirty_data_buffers]:782 bh->b_count 1, bh->b_page ffffea000709b000, page->index 0, i_ino 1033103, i_size 25165824
NILFS [nilfs_lookup_dirty_data_buffers]:783 bh->b_assoc_buffers.next ffff8802174a6798, bh->b_assoc_buffers.prev ffff880221cffee8
NILFS [nilfs_segctor_do_construct]:2336 nilfs_segctor_assign
NILFS [nilfs_segctor_do_construct]:2367 nilfs_segctor_update_segusage
NILFS [nilfs_segctor_do_construct]:2371 nilfs_segctor_prepare_write
NILFS [nilfs_segctor_do_construct]:2376 nilfs_add_checksums_on_logs
NILFS [nilfs_segctor_do_construct]:2381 nilfs_segctor_write
NILFS [nilfs_segbuf_submit_bh]:575 bh->b_count 1, bh->b_page ffffea000709b000, page->index 0, i_ino 1033103, i_size 25165824
NILFS [nilfs_segbuf_submit_bh]:576 segbuf->sb_segnum 6784
NILFS [nilfs_segbuf_submit_bh]:577 bh->b_assoc_buffers.next ffff880218a0d5f8, bh->b_assoc_buffers.prev ffff880218bcdf50
NILFS [nilfs_segbuf_submit_bio]:464 bio->bi_sector 111150080, segbuf->sb_segnum 6784, segbuf->sb_nbio 0
[----------] ditto
NILFS [nilfs_segbuf_submit_bio]:464 bio->bi_sector 111164416, segbuf->sb_segnum 6784, segbuf->sb_nbio 15
[-----------------------------SEGMENT 6785-------------------------------]
NILFS [nilfs_segctor_do_construct]:2310 nilfs_segctor_begin_construction
NILFS [nilfs_segctor_do_construct]:2321 nilfs_segctor_collect
NILFS [nilfs_lookup_dirty_data_buffers]:782 bh->b_count 2, bh->b_page ffffea000709b000, page->index 0, i_ino 1033103, i_size 25165824
NILFS [nilfs_lookup_dirty_data_buffers]:783 bh->b_assoc_buffers.next ffff880219277e80, bh->b_assoc_buffers.prev ffff880221cffc88
NILFS [nilfs_segctor_do_construct]:2367 nilfs_segctor_update_segusage
NILFS [nilfs_segctor_do_construct]:2371 nilfs_segctor_prepare_write
NILFS [nilfs_segctor_do_construct]:2376 nilfs_add_checksums_on_logs
NILFS [nilfs_segctor_do_construct]:2381 nilfs_segctor_write
NILFS [nilfs_segbuf_submit_bh]:575 bh->b_count 2, bh->b_page ffffea000709b000, page->index 0, i_ino 1033103, i_size 25165824
NILFS [nilfs_segbuf_submit_bh]:576 segbuf->sb_segnum 6785
NILFS [nilfs_segbuf_submit_bh]:577 bh->b_assoc_buffers.next ffff880218a0d5f8, bh->b_assoc_buffers.prev ffff880222cc7ee8
NILFS [nilfs_segbuf_submit_bio]:464 bio->bi_sector 111165440, segbuf->sb_segnum 6785, segbuf->sb_nbio 0
[----------] ditto
NILFS [nilfs_segbuf_submit_bio]:464 bio->bi_sector 111177728, segbuf->sb_segnum 6785, segbuf->sb_nbio 12
NILFS [nilfs_segctor_do_construct]:2399 nilfs_segctor_wait
NILFS [nilfs_segbuf_wait]:676 segbuf->sb_segnum 6783
NILFS [nilfs_segbuf_wait]:676 segbuf->sb_segnum 6784
NILFS [nilfs_segbuf_wait]:676 segbuf->sb_segnum 6785
NILFS [nilfs_segctor_complete_write]:2100 bh->b_count 0, bh->b_blocknr 13895680, bh->b_size 13897727, bh->b_page 0000000000001a82
BUG: unable to handle kernel paging request at 0000000000001a82
IP: [<ffffffffa024d0f2>] nilfs_end_page_io+0x12/0xd0 [nilfs2]
Usually, for every segment we collect dirty files in list. Then, dirty
blocks are gathered for every dirty file, prepared for write and
submitted by means of nilfs_segbuf_submit_bh() call. Finally, it takes
place complete write phase after calling nilfs_end_bio_write() on the
block layer. Buffers/pages are marked as not dirty on final phase and
processed files removed from the list of dirty files.
It is possible to see that we had three prepare_write and submit_bio
phases before segbuf_wait and complete_write phase. Moreover, segments
compete between each other for dirty blocks because on every iteration
of segments processing dirty buffer_heads are added in several lists of
payload_buffers:
[SEGMENT 6784]: bh->b_assoc_buffers.next ffff880218a0d5f8, bh->b_assoc_buffers.prev ffff880218bcdf50
[SEGMENT 6785]: bh->b_assoc_buffers.next ffff880218a0d5f8, bh->b_assoc_buffers.prev ffff880222cc7ee8
The next pointer is the same but prev pointer has changed. It means
that buffer_head has next pointer from one list but prev pointer from
another. Such modification can be made several times. And, finally, it
can be resulted in various issues: (1) segctor hanging, (2) segctor
crashing, (3) file system metadata corruption.
FIX:
This patch adds:
(1) setting of BH_Async_Write flag in nilfs_segctor_prepare_write()
for every proccessed dirty block;
(2) checking of BH_Async_Write flag in
nilfs_lookup_dirty_data_buffers() and
nilfs_lookup_dirty_node_buffers();
(3) clearing of BH_Async_Write flag in nilfs_segctor_complete_write(),
nilfs_abort_logs(), nilfs_forget_buffer(), nilfs_clear_dirty_page().
Reported-by: Jerome Poulin <jeromepoulin@gmail.com>
Reported-by: Anton Eliasson <devel@antoneliasson.se>
Cc: Paul Fertser <fercerpav@gmail.com>
Cc: ARAI Shun-ichi <hermes@ceres.dti.ne.jp>
Cc: Piotr Szymaniak <szarpaj@grubelek.pl>
Cc: Juan Barry Manuel Canham <Linux@riotingpacifist.net>
Cc: Zahid Chowdhury <zahid.chowdhury@starsolutions.com>
Cc: Elmer Zhang <freeboy6716@gmail.com>
Cc: Kenneth Langga <klangga@gmail.com>
Signed-off-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Han Pingtian found a typo in Documentation/kernel-parameters.txt about
"kernelcore=", that "kernelcore" should be replaced with "Movable" here.
Signed-off-by: Weiping Pan <wpan@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "force" parameter in __blk_queue_bounce was being ignored, which
means that stable page snapshots are not always happening (on ext3).
This of course leads to DIF disks reporting checksum errors, so fix this
regression.
The regression was introduced in commit 6bc454d150 ("bounce: Refactor
__blk_queue_bounce to not use bi_io_vec")
Reported-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If /proc/sys/kernel/core_pattern contains only "|", a NULL pointer
dereference happens upon core dump because argv_split("") returns
argv[0] == NULL.
This bug was once fixed by commit 264b83c07a ("usermodehelper: check
subprocess_info->path != NULL") but was by error reintroduced by commit
7f57cfa4e2 ("usermodehelper: kill the sub_info->path[0] check").
This bug seems to exist since 2.6.19 (the version which core dump to
pipe was added). Depending on kernel version and config, some side
effect might happen immediately after this oops (e.g. kernel panic with
2.6.32-358.18.1.el6).
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The proc interface is not aware of sem_lock(), it instead calls
ipc_lock_object() directly. This means that simple semop() operations
can run in parallel with the proc interface. Right now, this is
uncritical, because the implementation doesn't do anything that requires
a proper synchronization.
But it is dangerous and therefore should be fixed.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Operations that need access to the whole array must guarantee that there
are no simple operations ongoing. Right now this is achieved by
spin_unlock_wait(sem->lock) on all semaphores.
If complex_count is nonzero, then this spin_unlock_wait() is not
necessary, because it was already performed in the past by the thread
that increased complex_count and even though sem_perm.lock was dropped
inbetween, no simple operation could have started, because simple
operations cannot start when complex_count is non-zero.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Mike Galbraith <bitbucket@online.de>
Cc: Rik van Riel <riel@redhat.com>
Reviewed-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The exclusion of complex operations in sem_lock() is insufficient: after
acquiring the per-semaphore lock, a simple op must first check that
sem_perm.lock is not locked and only after that test check
complex_count. The current code does it the other way around - and that
creates a race. Details are below.
The patch is a complete rewrite of sem_lock(), based in part on the code
from Mike Galbraith. It removes all gotos and all loops and thus the
risk of livelocks.
I have tested the patch (together with the next one) on my i3 laptop and
it didn't cause any problems.
The bug is probably also present in 3.10 and 3.11, but for these kernels
it might be simpler just to move the test of sma->complex_count after
the spin_is_locked() test.
Details of the bug:
Assume:
- sma->complex_count = 0.
- Thread 1: semtimedop(complex op that must sleep)
- Thread 2: semtimedop(simple op).
Pseudo-Trace:
Thread 1: sem_lock(): acquire sem_perm.lock
Thread 1: sem_lock(): check for ongoing simple ops
Nothing ongoing, thread 2 is still before sem_lock().
Thread 1: try_atomic_semop()
<<< preempted.
Thread 2: sem_lock():
static inline int sem_lock(struct sem_array *sma, struct sembuf *sops,
int nsops)
{
int locknum;
again:
if (nsops == 1 && !sma->complex_count) {
struct sem *sem = sma->sem_base + sops->sem_num;
/* Lock just the semaphore we are interested in. */
spin_lock(&sem->lock);
/*
* If sma->complex_count was set while we were spinning,
* we may need to look at things we did not lock here.
*/
if (unlikely(sma->complex_count)) {
spin_unlock(&sem->lock);
goto lock_array;
}
<<<<<<<<<
<<< complex_count is still 0.
<<<
<<< Here it is preempted
<<<<<<<<<
Thread 1: try_atomic_semop() returns, notices that it must sleep.
Thread 1: increases sma->complex_count.
Thread 1: drops sem_perm.lock
Thread 2:
/*
* Another process is holding the global lock on the
* sem_array; we cannot enter our critical section,
* but have to wait for the global lock to be released.
*/
if (unlikely(spin_is_locked(&sma->sem_perm.lock))) {
spin_unlock(&sem->lock);
spin_unlock_wait(&sma->sem_perm.lock);
goto again;
}
<<< sem_perm.lock already dropped, thus no "goto again;"
locknum = sops->sem_num;
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Mike Galbraith <bitbucket@online.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We've been getting warnings about an excessive amount of time spent
allocating pages for migration during memory compaction without
scheduling. isolate_freepages_block() already periodically checks for
contended locks or the need to schedule, but isolate_freepages() never
does.
When a zone is massively long and no suitable targets can be found, this
iteration can be quite expensive without ever doing cond_resched().
Check periodically for the need to reschedule while the compaction free
scanner iterates.
Signed-off-by: David Rientjes <rientjes@google.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A high setting of max_map_count, and a process core-dumping with a large
enough vm_map_count could result in an NT_FILE note not being written,
and the kernel crashing immediately later because it has assumed
otherwise.
Reproduction of the oops-causing bug described here:
https://lkml.org/lkml/2013/8/30/50
Rge ussue originated in commit 2aa362c49c ("coredump: extend core dump
note section to contain file names of mapped file") from Oct 4, 2012.
This patch make that section optional in that case. fill_files_note()
should signify the error, and also let the info struct in
elf_core_dump() be zero-initialized so that we can check for the
optionally written note.
[akpm@linux-foundation.org: avoid abusing E2BIG, remove a couple of not-really-needed local variables]
[akpm@linux-foundation.org: fix sparse warning]
Signed-off-by: Dan Aloni <alonid@stratoscale.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Reported-by: Martin MOKREJS <mmokrejs@gmail.com>
Tested-by: Martin MOKREJS <mmokrejs@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit cea27eb2a2 ("mm/memory-hotplug: fix lowmem count
overflow when offline pages").
The fixed bug by commit cea27eb was fixed to another way by commit
3dcc0571cd ("mm: correctly update zone->managed_pages"). That commit
enhances memory_hotplug.c to adjust totalhigh_pages when hot-removing
memory, for details please refer to:
http://marc.info/?l=linux-mm&m=136957578620221&w=2
As a result, commit cea27eb2a2 currently causes duplicated decreasing
of totalhigh_pages, thus the revert.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the the debugfs entries in iio_device_unregister(). Otherwise the debugfs
entries might still be accessible even though the device used in the debugfs
callback has already been freed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
fq_reset() should drops all packets in queue, including
throttled flows.
This patch moves code from fq_destroy() to fq_reset()
to do the cleaning.
fq_change() must stop calling fq_dequeue() if all remaining
packets are from throttled flows.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 8ed781668d ("flow_keys: include thoff into flow_keys for
later usage"), we missed that existing code was using nhoff as a
temporary variable that could not always contain transport header
offset.
This is not a problem for TCP/UDP because port offset (@poff)
is 0 for these protocols.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the frontend state changes netback now specifies its desired state to
a new function, set_backend_state(), which transitions through any
necessary intermediate states.
This fixes an issue observed with some old Windows frontend drivers where
they failed to transition through the Closing state and netback would not
behave correctly.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the scenario where an IPv6 router is advertising a fixed
preferred_lft of 1800 seconds, while the valid_lft begins at 3600
seconds and counts down in realtime.
A client should reset its preferred_lft to 1800 every time the RA is
received, but a bug is causing Linux to ignore the update.
The core problem is here:
if (prefered_lft != ifp->prefered_lft) {
Note that ifp->prefered_lft is an offset, so it doesn't decrease over
time. Thus, the comparison is always (1800 != 1800), which fails to
trigger an update.
The most direct solution would be to compute a "stored_prefered_lft",
and use that value in the comparison. But I think that trying to filter
out unnecessary updates here is a premature optimization. In order for
the filter to apply, both of these would need to hold:
- The advertised valid_lft and preferred_lft are both declining in
real time.
- No clock skew exists between the router & client.
So in this patch, I've set "update_lft = 1" unconditionally, which
allows the surrounding code to be greatly simplified.
Signed-off-by: Paul Marks <pmarks@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While sending packet skb_cow_head() can change skb header which
invalidates inner_iph pointer to skb header. Following patch
avoid using it. Found by code inspection.
This bug was introduced by commit 0e6fbc5b6c (ip_tunnels: extend
iptunnel_xmit()).
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cinterion PLXX LTE devices have a 0x0060 product ID, not 0x12d1.
The blacklisting in the serial/option driver does actually use the correct PID,
as per commit 8ff10bdb14 ('USB: Blacklisted
Cinterion's PLxx WWAN Interface').
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
Signed-off-by: Aleksander Morgado <aleksander@lanedo.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Christian Schmiedl <christian.schmiedl@gemalto.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.
For instance:
fsl,cksel = <0>;
for using external (TSEC_TMR_CLK input) high precision timer
reference clock.
Other acceptable values:
<1> : eTSEC system clock
<2> : eTSEC1 transmit clock
<3> : RTC clock input
When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of RCU api makes vxlan code easier to understand. It also
fixes bug due to missing ACCESS_ONCE() on sk_user_data dereference.
In rare case without ACCESS_ONCE() compiler might omit vs on
sk_user_data dereference.
Compiler can use vs as alias for sk->sk_user_data, resulting in
multiple sk_user_data dereference in rcu read context which
could change.
CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quite a few fixes here, mostly small driver specific ones. The stand
out thing is a fix for errors generating the documentation from Randy
Dunlap, otherwise unless you're using the driver in question there
should be no impact.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=g543
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Quite a few fixes here, mostly small driver specific ones.
The stand out thing is a fix for errors generating the documentation
from Randy Dunlap, otherwise unless you're using the driver in
question there should be no impact"
* tag 'regulator-v3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: ti-abb: Fix bias voltage glitch in transition to bypass mode
regulator: wm831x-ldo: Fix max_uV for gp_ldo and aldo linear range settings
regulator: wm8350: correct the max_uV of LDO
regulator: fix fatal kernel-doc error
regulator: palmas: Remove wrong comment for the equation calculating num_voltages
regulator: da9063: Fix PTR_ERR/ERR_PTR mismatch
regulator: palmas: configure enable time for LDOs
regulator: palmas: fix the n_voltages for smps to 122
Pull apparmor fixes from James Morris:
"Bugfixes for the Apparmor code for regressions introduced in the 3.12
pull request"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
apparmor: fix suspicious RCU usage warning in policy.c/policy.h
apparmor: Use shash crypto API interface for profile hashes
Pull assorted vfs fixes from Al Viro:
"A couple of bug fixes + removal of dead code in afs ->d_revalidate()"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
afs: dget_parent() can't return a negative dentry
ocfs2: needs ->d_lock to poke in ->d_parent->d_inode from ->d_revalidate()
sysv: Add forgotten superblock lock init for v7 fs
Since the patch "cpufreq: cpufreq-cpu0: NULL is a valid regulator", cpu_reg
contains an error value if the regulator is not set, instead of NULL.
Accordingly, fix the remaining check for non-NULL cpu_reg.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
'clk_round_rate' returns a negative error code upon failure. This
will never get detected by unsigned 'newfreq'. Make it signed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Recent commit 8fd37a4 (PM / hibernate: Create memory bitmaps after
freezing user space) broke the resume part of the user space driven
hibernation (s2disk), because I forgot that the resume utility
loaded the image into memory without freezing user space (it still
freezes tasks after loading the image). This means that during user
space driven resume we need to create the memory bitmaps at the
"device open" time rather than at the "freeze tasks" time, so make
that happen (that's a special case anyway, so it needs to be treated
in a special way).
Reported-and-tested-by: Ronald <ronald645@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull AVR32 fixes from Hans-Christian Egtvedt.
Fix build warnings and use the Kbuild infrastructure for generic headers
rather than doing it by hand.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: cast syscall_return to silence compiler warning
avr32: fix clockevents kernel warning
avr32: use Kbuild infrastructure to handle the asm-generic headers
Pull S+core fixes from Lennox Wu:
"These updates include updating information of maintainers, fix some
trivial errors, and add a necessary function for supporting ipv6"
* tag 'for-linus-20130929' of git://github.com/sctscore/official-linux:
Score: Update the information of Score maintaners
Score: Modify the Makefile of Score, remove -mlong-calls for compiling
Score: Implement the function csum_ipv6_magic
Score: The commit is for compiling successfully
Eric Dumazet