The documentation is a little iffy as to whether these are actual MMRs,
but reading them on the hardware works, and the previous version of this
logic (the SDH) had PID[4567]. So add it for RSI too.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This code was mostly developed against a BF54x, so some BF537-specific
issues were missed.
The PPI block starts at PPI_CONTROL, not PPI_STATUS (which is the reverse
of the EPPI block).
The MDMA block starts at MDMA_NEXT_DESC_PTR, not MDMA_CONFIG. Seems the
sim does not catch misreads here so that'll need to get fixed.
The gptimer block is mostly 32bit regs, not 16bit. Use the gptimer struct
to figure that out rather than hardcoding it locally.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin percpu input sections are outdated, so rather than update
them, drop them completely and use the new common define.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Anomaly 05000480 on BF537 rev 0.0, 0.1, 0.2:
Multiple Simultaneous Urgent DMA Requests May Cause DMA System Instability
Suggested Workaround:
Program the DMA Traffic Control Period to a non-zero value. This forces
the DMA block to group accesses together rather than allow arbitration for
each piece of data placed on the internal DMA bus.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
old cpu_xxx() APIs is planned to removed later. then, converted.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Every callter (except kthread_bind) should use proper
set_cpus_allowed_ptr() APIs.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Turns out the documentation is wrong and doing "RAISE 1" does not result
in a software reset, only a core reset. So when the on-chip rom has a
functioning reset helper, use it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since the value of these MMRs aren't changing, store the value in a local
variable and work off of that. This avoids multiple MMR reads which are
implicitly forced by the volatile markings.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF537 SIC combines the gpio port H mask A interrupts with the
emac rx interrupt, so we need to demux this in software.
It also combines the gpio port H mask B and the emac tx interrupts,
and the watchdog and port F mask B interrupts, but since we don't
support mask B yet, just add the defines for now.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
These are only used in a few internal Blackfin places, so move the irq
prototypes out of the global header and into the internal irq one. No
functional changes other than shuffling locales.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
After some cache setup reordering changesets, the blackfin_cpudata init
was left behind. While cpu0's data was correct, cpu1's data was not.
Not that big of a deal as these are only used in the cpuinfo output, but
should still be fixed. So move the setup of these fields to the common
cache setup function to avoid this happening again in the future.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The smp flush lines are too long and have too many newlines, so scale
them back to match the other lines.
The %p modifier shows "(null)" for 0, so use %08x instead.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'for-2.6.40' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: Unify input section names
percpu: Avoid extra NOP in percpu_cmpxchg16b_double
percpu: Cast away printk format warning
percpu: Always align percpu output section to PAGE_SIZE
Fix up fairly trivial conflict in arch/x86/include/asm/percpu.h as per Tejun
* 'timers-clocksource-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: convert mips to generic i8253 clocksource
clocksource: convert x86 to generic i8253 clocksource
clocksource: convert footbridge to generic i8253 clocksource
clocksource: add common i8253 PIT clocksource
blackfin: convert to clocksource_register_hz
mips: convert to clocksource_register_hz/khz
sparc: convert to clocksource_register_hz/khz
alpha: convert to clocksource_register_hz
microblaze: convert to clocksource_register_hz/khz
ia64: convert to clocksource_register_hz/khz
x86: Convert remaining x86 clocksources to clocksource_register_hz/khz
Make clocksource name const
Conflicts:
arch/ia64/kernel/cyclone.c
arch/mips/kernel/i8253.c
arch/x86/kernel/i8253.c
Reason: Resolve conflicts so further cleanups do not conflict further
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Convert some Blackfin architecture's code to using struct syscore_ops
objects for power management instead of sysdev classes and sysdevs.
This simplifies the code and reduces the kernel's memory footprint.
It also is necessary for removing sysdevs from the kernel entirely in
the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
If the period of a gptimer is fairly low, we might miss an interrupt
by acking it too late (we end up acking the new int as well).
Reported-by: Isabelle Leonardi <i.leonardi@detracom.fr>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We only want to clear the run bit for this one timer, not all status bits.
So don't read the whole reg and then write all the bits back out.
Reported-by: Isabelle Leonardi <i.leonardi@detracom.fr>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
Blackfin: bitops: fix include order after little endian inclusion
Blackfin: defconfigs: update after misc devices defaulted to N
Blackfin: use more standard pr_fmt in the module loader
Convert to the new function names. Scripted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Changed pr_fmt(fmt) to make the format arguments match the format.
Changed an argument name in apply_relocate from me to mod so that
the pr_err is consistent with the other uses.
Added missing '\n' to a format.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Percpu allocator honors alignment request upto PAGE_SIZE and both the
percpu addresses in the percpu address space and the translated kernel
addresses should be aligned accordingly. The calculation of the
former depends on the alignment of percpu output section in the kernel
image.
The linker script macros PERCPU_VADDR() and PERCPU() are used to
define this output section and the latter takes @align parameter.
Several architectures are using @align smaller than PAGE_SIZE breaking
percpu memory alignment.
This patch removes @align parameter from PERCPU(), renames it to
PERCPU_SECTION() and makes it always align to PAGE_SIZE. While at it,
add PCPU_SETUP_BUG_ON() checks such that alignment problems are
reliably detected and remove percpu alignment comment recently added
in workqueue.c as the condition would trigger BUG way before reaching
there.
For um, this patch raises the alignment of percpu area. As the area
is in .init, there shouldn't be any noticeable difference.
This problem was discovered by David Howells while debugging boot
failure on mn10300.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: user-mode-linux-devel@lists.sourceforge.net
This patch introduces Blackfin-specific bits to support the current
tip of the interrupt pipeline development, mainly:
- 2/3-level interrupt maps (sparse IRQs)
- generic virq handling
- sysinfo v2 format for ipipe_get_sysinfo()
Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
In order to safely work around anomaly 05000491, we have to execute IFLUSH
from L1 instruction sram. The trouble with multi-core systems is that all
L1 sram is visible only to the active core. So we can't just place the
functions into L1 and call it directly. We need to setup a jump table and
place the entry point in external memory. This will call the right func
based on the active core.
In the process, convert from the manual relocation of a small bit of code
into Core B's L1 to the more general framework we already have in place
for loading arbitrary pieces of code into L1.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Common code checks the alignment of some of the variables and calls BUG()
if they aren't page aligned.
Signed-off-by: steven miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Common code no longer defines this, so stop using it.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF54x lacks dedicated DMA channels for the UART peripherals and need
to be muxed between others. So add a kconfig option so people can select
which channels the UARTs will use so they can pick between SPORTs and the
less commonly used EPPI/PIXC peripherals.
Signed-off-by: steven miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'for-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu, x86: Add arch-specific this_cpu_cmpxchg_double() support
percpu: Generic support for this_cpu_cmpxchg_double()
alpha: use L1_CACHE_BYTES for cacheline size in the linker script
percpu: align percpu readmostly subsection to cacheline
Fix up trivial conflict in arch/x86/kernel/vmlinux.lds.S due to the
percpu alignment having changed ("x86: Reduce back the alignment of the
per-CPU data section")
This converts the blackfin clocksource to use clocksource_register_hz.
CC: Mike Frysinger <vapier@gentoo.org>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Currently percpu readmostly subsection may share cachelines with other
percpu subsections which may result in unnecessary cacheline bounce
and performance degradation.
This patch adds @cacheline parameter to PERCPU() and PERCPU_VADDR()
linker macros, makes each arch linker scripts specify its cacheline
size and use it to align percpu subsections.
This is based on Shaohua's x86 only patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Shaohua Li <shaohua.li@intel.com>
We check its value at runtime, so we want to avoid garbage across runs.
Signed-off-by: Vivi Li <vivi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Otherwise, gdb continue operation after a breakpoint is hit may trap
into endless breakpoint.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When ADEOS and kgdb are both enabled, single step in linux kernel may be
scheduled to Xenomai core after return from interrupt handlers. This
blocks gdb continue operation after a break point is hit. So, disable
interrupt when running gdb single step.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When using an uncached DMA region less than 1 MiB, we try to mask off
the whole last 1 MiB for it. Unfortunately, this fails as we forgot
to subtract one from the calculated mask, leading to the region still
be marked as cacheable.
Reported-by: Andrew Rook <andrew.rook@speakerbus.co.uk>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kgdb_disable_hw_debug() was an architecture specific function for
disabling all hardware breakpoints on a per cpu basis when entering
the debug core.
This patch will remove the weak function kdbg_disable_hw_debug() and
change it into a call back which lives with the rest of hw breakpoint
call backs in struct kgdb_arch.
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Change signature of get/put_reg() according to the change of arch_ptrace()
and remove unnecessary castings.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the arguments to arch_ptrace() to take account of the fact that
@addr and @data are now unsigned long rather than long as of a preceding
patch in this series.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
Mike Frysinger