FW starts using legacy power table command (0x77) for device wide power
settings. Currently this command contains only option flags field.
It can configure the following: CAM (Continuous Active Mode) and
POWER_SAVE_ENABLE debug option. Send this command when firmware is
loaded - D0 and D3.
Note: Setting this command is important to avoid unwanted FW behavior.
It particularly fixes a bug when a device does not drop to low power
after disassociation from AP.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This should really not happen. If it does, restarting is the
only way to recover since the driver and the firmware might
very well be out of sync. Moreover, iwl_op_mode_nic_error
will print data that might help debugging.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Single shared antenna devices need a special LUT.
Address this need.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In loose BT Coex scheme, the aggregation size doesn't need to
be limited.
To avoid triggering it, remove a lockdep assertion - we need
to compute the AMPDU size limit from rate control code which
can't take mvm->mutex. This means that there is a race but in
the worst case, we will have a wrong AMPDU size limit which
is not a big issue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In RF KILL the init ucode is running, but don't complete
all its tasks, so we need to run the init ucode again.
Change the flag name to init_ucode_complete, to be more appropriate.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware API for IPv6 NDP/NS offload has changed again.
Implement support for the new API; this requires calculating
the solicited node address for each "target" address as it's
no longer ignored by the firmware.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rssi events were enabled on interfaces using 5.2GHz.
Interfaces on 5.2GHz were taken into account while
determining the ACK / CTS kill mask. Fix that.
The last rssi notified to BT Coex was reset every BT Coex
Notification. Since we get a lot of these notifications
from the firmware, we reset the rssi all the time which
means that the bt_rssi_event is called all the time.
Fix that by puting the rssi we pull upon BT Coex
notification into iwl_mvm_vif_bf_data.last_bt_coex_event
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we have only one antenna for BT and WiFi, reduced Tx
power is irrelevant.
Also, in loose scheme, we should not use reduced Tx power
nor set the control mask to Tx power.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some debugfs write() operations of the MVM Firmware will ignore the
count argument, and will copy more bytes than what was specified.
Fix this by getting the right count of bytes.
This will honor restrictions put on the number of bytes to write and
avoid strcmp() calls on garbage data.
Signed-off-by: Djalal Harouni <tixxdz@opendz.org>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mvm doesn't support HT GF so drop all relevant code in rs.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enable rs algorithm to use VHT rates and use 80Mhz.
This enables reaching VHT rates which wasn't possible.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The data in MailBox comes direclty from the BT core.
We should use the data processed by the WiFi fw that is
appended to the MailBox in the BT Coex notification.
Also decide on whether the Coex type based on the input
from the the firmware and not hard coded.
Also fix the SMPS SISO threshold to 2 (it was 3).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was due to a fw remainder of old implementation.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is the new API for BT Coex. The full functionality
will be implemented in further patches.
Note: this disables BT Coex for the currently existing
fw (-7 version).
There is also a new command - the channel inhibition command.
This command tells BT what channels to avoid in order to
minimise the interaction between BT and WiFi.
We can tell BT about 2 channels, primary and secondary.
BT will not tune to primary at all and will avoid secondary
as much as possible.
This also means that we need to track vifs that AP / GO.
So rename iwl_mvm_bt_coex_vif_assoc to
iwl_mvm_bt_coex_vif_change to better reflect its real
meaning.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for scheduled scan according to firmware support.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
New FW doesn't use the SSID from scan request template. Adding
a TLV flag to indicate the change, and fixing the flows to send
the first SSID in SSID list if the flag is on.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We want to dump the SRAM when we have an error interrupt
from the device. This happens in non-sleepable context,
hence the change.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
VHT introduces MCS8 and MCS9. Update the expected tpt tables
to include these. Previous expected values for 20/40 MHz
are incorrect in certain cases so fix these as well.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Tested-by: Efi Tubul <efi.tubul@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current code didn't handle well the case where we're in SISO using
ANT B and there's a BT load. Switch to ANT A in this case.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Newer firmware don't clean the RFKILL interrupt in APMG, do
it in driver instead.
If we forget to do so, we can't send HCMD to firmware while
the NIC is in RFKILL state.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for new station management firmware API. The old
ADD_MODIFY_STA command has been replaced with two: a modified
ADD_MODIFY_STA and a new ADD_MODIFY_STA_KEY command.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adjust the following:
- RX/TX AP-to-PSM timeout in case of uAPSD and PBW snoozing
- PSM-to-AM TX/RX heavy traffic thresholds
- Beacon abort escape timer for D3/D0i3
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will deadlock due to commit 9f34783863bea806
("iwlwifi: mvm: Implement BT coex notifications"):
=============================================
[ INFO: possible recursive locking detected ]
3.5.0 #10 Tainted: G W O
---------------------------------------------
kworker/2:1/5214 is trying to acquire lock:
(&mvm->mutex){+.+.+.}, at: [<ffffffffa03be23e>] iwl_mvm_bt_rssi_event+0x5e/0x210 [iwlmvm]
but task is already holding lock:
(&mvm->mutex){+.+.+.}, at: [<ffffffffa03ab2d9>] iwl_mvm_async_handlers_wk+0x49/0x120 [iwlmvm]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&mvm->mutex);
lock(&mvm->mutex);
*** DEADLOCK ***
Change-Id: I9104f252b34676e2f7ffcd51166f95367e08a4d9
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-on: https://gerrit.rds.intel.com/21887
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/wireless/iwlwifi/mvm/bt-coex.c
Use beacon statistics notification handler
to notify bt coex about rssi changes.
Mac80211's mechanism is not used anymore.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When firmware restart happens, the timers are obviously reset and
the new firmware has no synchronisation with the AP as we program
timings to the pre-restart values. The firmware should attempt to
synchronise by itself, but in multi-channel scenarios this isn't
easy, particularly since it has to try to keep service quality up
for other MACs.
To make it more reliable, give each client MAC some time to catch
beacons when restarting or resuming. Service quality was impacted
anyway (or in resume doesn't really matter much.)
Reviewed-by: Moshe Island <moshe.island@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The XXX_SWITCH_ANTENNA1/2 actions keep track of switching between
3 single antennas or between 3 pairs in case of MIMO2 on a MIMO3 device.
As current and future chips will have at most 2 antennas drop these.
While at it also convert the actions into enums and cleanup
the code a bit.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Newer firmware fixed a bug that prevented to use CTS to
self. Firmwares with API greater than 8 have this bug
fixed. Enable the feature for these firmwares only.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an option to set rx antennas for the scan command from debugfs.
Create a file called ant_rxchain in the mvm debugfs directory.
To choose antennas, write a number between 1-7 to ant_rxchain.
Write 1 for A, 2 for B, 3 for AB and so on.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of keeping track of the non-QoS seqno for each station,
query the firmware when suspending, that's more efficient. As
this can fail, move the station ID mangling later in the code.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a testmode command to (manually) disable (and re-enable)
beacon filtering for testing purposes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For testing, implement setting continuous NoA duration
using a new MVM-specific testmode command.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LeaW
-----END PGP SIGNATURE-----
Merge tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script: (and a little typing)
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please accept this batch of updates intended for the 3.12 stream.
For the mac80211 bits, Johannes says this:
"This time I have various improvements all over the place: IBSS, mesh,
testmode, AP client powersave handling, one of the rare rfkill patches
and some code cleanup."
Also for mac80211:
"And I also have some more changes for -next, just a few small fixes and
improvements, nothing really stands out."
And for iwlwifi:
"This time I have some powersave work (notably uAPSD support), CQM
offloads, support for a new firmware API and various code cleanups."
Regarding the Bluetooth bits, Gustavo says:
"Patches to 3.12, here we have:
* implementation of a proper tty_port for RFCOMM devices, this fixes some
issues people were seeing lately in the kernel.
* Add voice_setting option for SCO, it is used for SCO Codec selection
* bugfixes, small improvements and clean ups"
For the NFC bits, Samuel says:
"With this one we have:
- A few pn533 improvements and minor fixes. Testing our pn533 driver
against Google's NCI stack triggered a few issues that we fixed now.
We also added Tx fragmentation support to this driver.
- More NFC secure element handling. We added a GET_SE netlink command
for getting all the discovered secure elements, and we defined 2
additional secure element netlink event (transaction and connectivity).
We also fixed a couple of typos and copy-paste bugs from the secure
element handling code.
- Firmware download support for the pn544 driver. This chipset can enter a
special mode where it's waiting for firmware blobs to replace the
already flashed one. We now support that mode."
With repect to the ath tree, Kalle says:
"New features in ath10k are rx/tx checsumming in hw and survey scan
implemented by Michal. Also he made fixes to different areas of the
driver, most notable being fixing the case when using two streams and
reducing the number of interface combinations to avoid firmware crashes.
Bartosz did a clean related to how we handle SoC power save in PCI
layer.
For ath6kl Mohammed and Vasanth sent each a patch to fix two infrequent
crashes."
I also pulled the wireless tree into wireless-next to support a
request from Johannes. On top of all that, there are the usual
sort of driver updates. The mwifiex, brcmfmac, brcmsmac, ath9k,
and rt2x00 drivers all get some attention, as does the bcma bus and
a few other random bits here and there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Cc: Jouni Malinen <j@w1.fi>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
__GFP_ZERO is an uncommon flag and perhaps is better
not used. static inline dma_zalloc_coherent exists
so convert the uses of dma_alloc_coherent with __GFP_ZERO
to the more common kernel style with zalloc.
Remove memset from the static inline dma_zalloc_coherent
and add just one use of __GFP_ZERO instead.
Trivially reduces the size of the existing uses of
dma_zalloc_coherent.
Realign arguments as appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to debug an interrupt delivery problem I noticed that not
all of the wakeup conditions on the worker thread were included in the
debug message. This patch rectifies that.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9462 requires this HW fix for ASPM to work properly.
Also, since WARegVal is used only for the AR8003 family,
use AR_SREV_9300_20_OR_LATER.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexander Bondar