When enabling EEH functionality on passed through devices (PE)
with VFIO, the devices in the PE would be removed permanently
from guest side. In that case, the PE remains frozen state.
When returning PE to host, or restarting the guest again, we
had mechanism unfreezing the PE by clearing PESTA/B frozen
bits. However, that's not enough for some adapters, which are
indicated as following "lspci" shows. Those adapters require
hot reset on the parent bus to bring their firmware back to
workable state. Otherwise, those adaptrs won't be operative
and the host (for returning case) or the guest will fail to
load the drivers for those adapters without exception.
0000:01:00.0 Ethernet controller: Emulex Corporation OneConnect \
10Gb NIC (be3) (rev 02)
0000:01:00.0 0200: 19a2:0710 (rev 02)
0001:03:00.0 Ethernet controller: Emulex Corporation OneConnect \
NIC (Lancer) (rev 10)
0001:03:00.0 0200: 10df:e220 (rev 10)
The patch adds mechanism to emulate EEH recovery (for hot reset
on parent PCI bus) on 3 gates to fix the issue: open/release one
adapter of the PE, enable EEH functionality on one adapter of the
PE.
Reported-by: Murilo Fossa Vicentini <muvic@br.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PE would be owned by userland, which probably request PE reset
done in host side. During the reset, we should drop the PCI
config accesses to the PE with help of flag EEH_PE_RESET.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The names of PCI reset scopes aren't sychronized with firmware.
The patch fixes it.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As Anton suggested, the patch decreases the message level on EEH
initialization to avoid unnecessary messages if required. Also,
we have unified hint if any of needful RTAS calls is missed, and
then we can check /proc/device-tree to figure out the missed RTAS
calls.
Suggested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Function pcibios_set_pcie_reset_state() can be used to do PCI
reset. PCI config access during the reset usually causes EEH
errors unexpectedly. In order to avoid the EEH error, the patch
blocks PCI config access during reset with the help of flag
EEH_PE_RESET, which is similar to what we did in EEH PE reset
path.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch uses eeh_unfreeze_pe() to replace the logic clearing
frozen IO and DMA, in order to simplify the code.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When passing through PE to guest, that's possibly in frozen
state. The driver for the pass-through devices on guest side
can't be loaded successfully as reported. We already had one
gate in eeh_dev_open() to clear PE frozen state accordingly,
but that's not enough because the function is only called at
QEMU startup for once.
The patch adds another gate in eeh_pe_set_option() so that the
PE frozen state can be cleared at QEMU restart time.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function eeh_pci_enable() is called to apply various requests
to one particular PE: Enabling EEH, Disabling EEH, Enabling IO,
Enabling DMA, Freezing PE. When enabling IO or DMA on one specific
PE, we need check that IO or DMA isn't enabled previously. But
the condition used to do the check isn't completely correct because
one PE would be in DMA frozen state with workable IO path, or vice
versa.
The patch fixes the improper condition.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The problem was reported by Carol: In the scenario of passing mlx4
adapter to guest, EEH error could be recovered successfully. When
returning the device back to host, the driver (mlx4_core.ko)
couldn't be loaded successfully because of error number -5 (-EIO)
returned from mlx4_get_ownership(), which hits offlined PCI device.
The root cause is that we missed to put the affected devices into
normal state on clearing PE isolated state right after PE reset.
The patch fixes above issue by putting the affected devices to
normal state when clearing PE isolated state in eeh_pe_state_clear().
Cc: stable@vger.kernel.org
Reported-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The frozen state on one specific PE is probably caused by error
injection, which is done with help of PAPR error injection registers.
According to the hardware spec, those registers should be cleared
automatically after one-shot frozen PE. However, that's not always
true, at least on P7IOC of Firebird-L. So we have to clear them
before doing PE reset to avoid recursive EEH errors at recovery
stage.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch adds debugfs file (/sys/kernel/debug/powerpc/PCIxxxx/
err_injct), which accepts following formated string, to support
error injection. It will be used to support userland utility
"errinjct" in future.
"pe_no:0:function:address:mask" - 32-bits PCI errors
"pe_no:1:function:address:mask" - 64-bits PCI errors
Signed-off-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch introduces eeh_ops::err_inject(), which allows to inject
specified errors to indicated PE for testing purpose. The functionality
isn't support on pSeries platform. On PowerNV, the functionality
relies on OPAL API opal_pci_err_inject().
Signed-off-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When passing through device, its PE might have been put into frozen
state. One obvious example would be: the passed PE is forced to be
offline because of hitting maximal allowed EEH errors in userland.
In that case, the frozen state won't be cleared and then the PE is
returned back to host, which might not have chance detecting and
recovering from it.
The patch adds more check when passing through device and clear the
PE frozen state if necessary.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The PCI devices that have been passed through are enabled before
reset, we need restore to the enabled state after reset. Otherwise,
MMIO access might be issued to disabled devices after reset and
causes exceptional recursive EEH error.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch adds one more option (EEH_OPT_FREEZE_PE) to set_option()
method to proactively freeze PE, which will be issued before resetting
pass-throughed PE to drop MMIO access during reset because it's
always contributing to recursive EEH error.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch adds sysfs entry "eeh_pe_state". Reading on it returns
the PE's state while writing to it clears the frozen state. It's
used to check or clear the PE frozen state from userland for
debugging purpose.
The patch also replaces printk(KERN_WARNING ...) with pr_warn() in
eeh_sysfs.c
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_check_failure() is used to check frozen state of the PE which
owns the indicated I/O address. The argument "val" of the function
isn't used. The patch drops it and return the frozen state of the
PE as expected.
Cc: Vishal Mansur <vmansur@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are 2 MACIDs stored in the control module of the am33xx. These are
read by the cpsw driver if no valid MACID was found in the devicetree.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable on DCACHE_WORD_ACCESS on ppc64le. It should work on
ppc64 and ppc32 but we need to do some testing first.
A somewhat reasonable testcase used to show the performance
improvement - a repeated stat of a 33 byte filename that
doesn't exist:
#include <sys/types.h>
#include <sys/stat.h>
#include <unistd.h>
#define ITERATIONS 10000000
#define PATH "123456781234567812345678123456781"
int main(void)
{
unsigned long i;
struct stat buf;
for (i = 0; i < ITERATIONS; i++)
stat(PATH, &buf);
return 0;
}
runs 27% faster on POWER8.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use cmpb which compares each byte in two 64 bit values and
for each matching byte places 0xff in the target and 0x00
otherwise.
A simple hash_name microbenchmark:
http://ozlabs.org/~anton/junkcode/hash_name_bench.c
shows this version to be 10-20% faster than running the x86
version on POWER8, depending on the length.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It is a rarely exercised case, so we want to have a test to ensure it
works as required.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Implement a bi-arch and bi-endian version of load_unaligned_zeropad.
Since the fallback case is so rare, a userspace test harness was used
to test this on ppc64le, ppc64 and ppc32:
http://ozlabs.org/~anton/junkcode/test_load_unaligned_zeropad.c
It uses mprotect to force a SEGV across a page boundary, and a SEGV
handler to lookup the exception tables and run the fixup routine.
It also compares the result against a normal load.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We use cma reserved area for creating guest hash page table.
Don't do the reservation in non-hypervisor mode. This avoids unnecessary
CMA reservation when booting with limited memory configs like
fadump and kdump.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If CONFIG_TTY=n:
drivers/built-in.o: In function `rs_flush_buffer':
amiserial.c:(.text+0x1f626): undefined reference to `tty_wakeup'
drivers/built-in.o: In function `transmit_chars':
amiserial.c:(.text+0x1f6c8): undefined reference to `tty_wakeup'
drivers/built-in.o: In function `change_speed':
amiserial.c:(.text+0x1f80a): undefined reference to `tty_termios_baud_rate'
amiserial.c:(.text+0x1f88c): undefined reference to `tty_termios_baud_rate'
drivers/built-in.o: In function `check_modem_status':
amiserial.c:(.text+0x1faa6): undefined reference to `tty_hangup'
amiserial.c:(.text+0x1faec): undefined reference to `tty_wakeup'
drivers/built-in.o: In function `get_serial_info':
amiserial.c:(.text+0x1fb88): undefined reference to `tty_lock'
amiserial.c:(.text+0x1fbc0): undefined reference to `tty_unlock'
drivers/built-in.o: In function `rs_open':
amiserial.c:(.text+0x1fdc6): undefined reference to `tty_port_block_til_ready'
drivers/built-in.o: In function `set_serial_info':
amiserial.c:(.text+0x1fe0c): undefined reference to `tty_lock'
amiserial.c:(.text+0x1fea0): undefined reference to `tty_unlock'
amiserial.c:(.text+0x1fed0): undefined reference to `tty_unlock'
amiserial.c:(.text+0x1ffaa): undefined reference to `tty_unlock'
drivers/built-in.o: In function `receive_chars':
amiserial.c:(.text+0x2005c): undefined reference to `do_SAK'
amiserial.c:(.text+0x200e0): undefined reference to `tty_insert_flip_string_flags'
amiserial.c:(.text+0x2013c): undefined reference to `tty_insert_flip_string_flags'
amiserial.c:(.text+0x20148): undefined reference to `tty_flip_buffer_push'
drivers/built-in.o: In function `rs_close':
amiserial.c:(.text+0x20744): undefined reference to `tty_port_close_start'
amiserial.c:(.text+0x2078a): undefined reference to `tty_ldisc_flush'
amiserial.c:(.text+0x20798): undefined reference to `tty_port_close_end'
drivers/built-in.o: In function `amiga_serial_probe':
amiserial.c:(.init.text+0x96a): undefined reference to `__tty_alloc_driver'
amiserial.c:(.init.text+0x9c0): undefined reference to `tty_std_termios'
amiserial.c:(.init.text+0x9e6): undefined reference to `tty_set_operations'
amiserial.c:(.init.text+0xa3e): undefined reference to `tty_port_init'
amiserial.c:(.init.text+0xa5c): undefined reference to `tty_port_link_device'
amiserial.c:(.init.text+0xa6c): undefined reference to `tty_register_driver'
amiserial.c:(.init.text+0xb4a): undefined reference to `tty_unregister_driver'
amiserial.c:(.init.text+0xb58): undefined reference to `tty_port_destroy'
amiserial.c:(.init.text+0xb64): undefined reference to `put_tty_driver'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit: e676253b19 (serial/8250: Add
support for RS485 IOCTLs), adds support for RS485 ioctls for 825_core on
all the archs. Unfortunately the definition of TIOCSRS485 and
TIOCGRS485 was missing on the ioctls.h file
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The arch_timer_evtstrm_enable hooks in arm and arm64 are substantially
similar, the only difference being a CONFIG_COMPAT-conditional section
which is relevant only for arm64. Copy the arm64 version to the
driver, removing the arch-specific hooks.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
The only difference between arm and arm64's implementations of
arch_counter_set_user_access is that 32-bit ARM does not enable user
access to the virtual counter. We want to enable this access for the
32-bit ARM VDSO, so copy the arm64 version to the driver itself, and
remove the arch-specific implementations.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
If CONFIG_TTY=n:
drivers/built-in.o: In function `rs_flush_buffer':
amiserial.c:(.text+0x1f626): undefined reference to `tty_wakeup'
drivers/built-in.o: In function `transmit_chars':
amiserial.c:(.text+0x1f6c8): undefined reference to `tty_wakeup'
drivers/built-in.o: In function `change_speed':
amiserial.c:(.text+0x1f80a): undefined reference to `tty_termios_baud_rate'
amiserial.c:(.text+0x1f88c): undefined reference to `tty_termios_baud_rate'
drivers/built-in.o: In function `check_modem_status':
amiserial.c:(.text+0x1faa6): undefined reference to `tty_hangup'
amiserial.c:(.text+0x1faec): undefined reference to `tty_wakeup'
drivers/built-in.o: In function `get_serial_info':
amiserial.c:(.text+0x1fb88): undefined reference to `tty_lock'
amiserial.c:(.text+0x1fbc0): undefined reference to `tty_unlock'
drivers/built-in.o: In function `rs_open':
amiserial.c:(.text+0x1fdc6): undefined reference to `tty_port_block_til_ready'
drivers/built-in.o: In function `set_serial_info':
amiserial.c:(.text+0x1fe0c): undefined reference to `tty_lock'
amiserial.c:(.text+0x1fea0): undefined reference to `tty_unlock'
amiserial.c:(.text+0x1fed0): undefined reference to `tty_unlock'
amiserial.c:(.text+0x1ffaa): undefined reference to `tty_unlock'
drivers/built-in.o: In function `receive_chars':
amiserial.c:(.text+0x2005c): undefined reference to `do_SAK'
amiserial.c:(.text+0x200e0): undefined reference to `tty_insert_flip_string_flags'
amiserial.c:(.text+0x2013c): undefined reference to `tty_insert_flip_string_flags'
amiserial.c:(.text+0x20148): undefined reference to `tty_flip_buffer_push'
drivers/built-in.o: In function `rs_close':
amiserial.c:(.text+0x20744): undefined reference to `tty_port_close_start'
amiserial.c:(.text+0x2078a): undefined reference to `tty_ldisc_flush'
amiserial.c:(.text+0x20798): undefined reference to `tty_port_close_end'
drivers/built-in.o: In function `amiga_serial_probe':
amiserial.c:(.init.text+0x96a): undefined reference to `__tty_alloc_driver'
amiserial.c:(.init.text+0x9c0): undefined reference to `tty_std_termios'
amiserial.c:(.init.text+0x9e6): undefined reference to `tty_set_operations'
amiserial.c:(.init.text+0xa3e): undefined reference to `tty_port_init'
amiserial.c:(.init.text+0xa5c): undefined reference to `tty_port_link_device'
amiserial.c:(.init.text+0xa6c): undefined reference to `tty_register_driver'
amiserial.c:(.init.text+0xb4a): undefined reference to `tty_unregister_driver'
amiserial.c:(.init.text+0xb58): undefined reference to `tty_port_destroy'
amiserial.c:(.init.text+0xb64): undefined reference to `put_tty_driver'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
drivers/net/ethernet/cirrus/cs89x0.c: In function ‘cs89x0_ioport_probe’:
drivers/net/ethernet/cirrus/cs89x0.c:1629: error: implicit declaration of function ‘ioport_unmap’
Add the missing ioport_unmap() implementation, and convert ioport_map()
from a macro to a static inline function while we're at it (both copied
from asm-generic).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Here's our last set of fixes for 3.17. Most of these are for TI platforms,
fixing some noisy Kconfig issues, runtime clock and power issues on
several platforms and NAND timings on DRA7.
There are also a couple of bug fixes for i.MX, one for QCOM and a small
fix to avoid section mismatch noise on PXA.
Diffstat looks large, partially due to some tables being updated and
thus touching many lines. The qcom gsbi change also restructures clock
management a bit and thus touches a bunch of lines.
All in all, a bit more changes than we'd like at this point, but nothing
stands out as risky either so it seems like the right thing to send it
up now instead of holding it to the merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=K6xV
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's our last set of fixes for 3.17. Most of these are for TI
platforms, fixing some noisy Kconfig issues, runtime clock and power
issues on several platforms and NAND timings on DRA7.
There are also a couple of bug fixes for i.MX, one for QCOM and a
small fix to avoid section mismatch noise on PXA.
Diffstat looks large, partially due to some tables being updated and
thus touching many lines. The qcom gsbi change also restructures
clock management a bit and thus touches a bunch of lines.
All in all, a bit more changes than we'd like at this point, but
nothing stands out as risky either so it seems like the right thing to
send it up now instead of holding it to the merge window"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
drivers/soc: qcom: do not disable the iface clock in probe
ARM: imx: fix .is_enabled() of shared gate clock
ARM: OMAP3: Fix I/O chain clock line assertion timed out error
ARM: keystone: dts: fix bindings for pcie and usb clock nodes
bus: omap_l3_noc: Fix connID for OMAP4
ARM: DT: imx53: fix lvds channel 1 port
ARM: dts: cm-t54: fix serial console power supply.
ARM: dts: dra7-evm: Fix NAND GPMC timings
ARM: pxa: fix section mismatch warning for pxa_timer_nodt_init
ARM: OMAP: Fix Kconfig warning for omap1
Pull MIPS fixes from Ralf Baechle:
"The final round of fixes. One corner case in the math emulator and
another one in the mcount function for ftrace"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: mcount: Adjust stack pointer for static trace in MIPS32
MIPS: Fix MFC1 & MFHC1 emulation for 64-bit MIPS systems
Pull x86 fixes from Ingo Molnar:
"This has:
- EFI revert to fix a boot regression
- early_ioremap() fix for boot failure
- KASLR fix for possible boot failures
- EFI fix for corrupted string printing
- remove a misleading EFI bootup 'failed!' error message
Unfortunately it's all rather close to the merge window"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Truncate 64-bit values when calling 32-bit OutputString()
x86/efi: Delete misleading efi_printk() error message
Revert "efi/x86: efistub: Move shared dependencies to <asm/efi.h>"
x86/kaslr: Avoid the setup_data area when picking location
x86 early_ioremap: Increase FIX_BTMAPS_SLOTS to 8
This includes a bunch of changes:
- Support read-only memory slots on arm/arm64
- Various changes to fix Sparse warnings
- Correctly detect write vs. read Stage-2 faults
- Various VGIC cleanups and fixes
- Dynamic VGIC data strcuture sizing
- Fix SGI set_clear_pend offset bug
- Fix VTTBR_BADDR Mask
- Correctly report the FSC on Stage-2 faults
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUJWAdAAoJEEtpOizt6ddy9cMH+gIoUPnRJLe+PPcOOyxOx6pr
+CnD/zAd0sLvxZLP/LBOzu99H3YrbO5kwI/172/8G1zUNI2hp6YxEEJaBCTHrz6l
RwgLy7a3EMMY51nJo5w2dkFUo8cUX9MsHqMpl2Xb7Dvo2ZHp+nDqRjwRY6yi+t4V
dWSJTRG6X+DIWyysij6jBtfKU6MpU+4NW3Zdk1fapf8QDkn+cBtV5X2QcmERCaIe
A1j9hiGi43KA3XWeeePU3aVaxC2XUhTayP8VsfVxoNG2manaS6lqjmbif5ghs/0h
rw7R3/Aj0MJny2zT016MkvKJKRukuVRD6e1lcYghqnSJhL2FossowZ9fHRADpqU=
=QgU8
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-next
Changes for KVM for arm/arm64 for 3.18
This includes a bunch of changes:
- Support read-only memory slots on arm/arm64
- Various changes to fix Sparse warnings
- Correctly detect write vs. read Stage-2 faults
- Various VGIC cleanups and fixes
- Dynamic VGIC data strcuture sizing
- Fix SGI set_clear_pend offset bug
- Fix VTTBR_BADDR Mask
- Correctly report the FSC on Stage-2 faults
Conflicts:
virt/kvm/eventfd.c
[duplicate, different patch where the kvm-arm version broke x86.
The kvm tree instead has the right one]
We changed PAGE_OFFSET to be a variable rather than a constant,
but this reference here in the hibernate assembler got missed.
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF_LD | BPF_W | BPF_LEN instruction is occasionally used by tcpdump
and present in 11 tests in lib/test_bpf.c
Teach sparc JIT compiler to emit it.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-09-22
Please pull this batch of updates intended for the 3.18 stream...
For the mac80211 bits, Johannes says:
"This time, I have some rate minstrel improvements, support for a very
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed."
For the bluetooth bits, Johan says:
"Here are some more patches intended for 3.18. Most of them are cleanups
or fixes for SMP. The only exception is a fix for BR/EDR L2CAP fixed
channels which should now work better together with the L2CAP
information request procedure."
For the iwlwifi bits, Emmanuel says:
"I fix here dvm which was broken by my last pull request. Arik
continues to work on TDLS and Luca solved a few issues in CT-Kill. Eyal
keeps digging into rate scaling code, more to come soon. Besides this,
nothing really special here."
Beyond that, there are the usual big batches of updates to ath9k, b43,
mwifiex, and wil6210 as well as a handful of other bits here and there.
Also, rtlwifi gets some btcoexist attention from Larry.
Please let me know if there are problems!
====================
Had to adjust the wil6210 code to comply with Joe Perches's recent
change in net-next to make the netdev_*() routines return void instead
of 'int'.
Signed-off-by: David S. Miller <davem@davemloft.net>
done as separate commit to ease conflict resolution
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull scheduler fixes from Ingo Molnar:
"A CONFIG_STACK_GROWSUP=y fix, and a hotplug llc CPU mask fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix unreleased llc_shared_mask bit during CPU hotplug
sched: Fix end_of_stack() and location of stack canary for architectures using CONFIG_STACK_GROWSUP
The warning was introduced in 2009 (commit 4bf1fa5a34 ([ARM] 5613/1:
implement CALLER_ADDRESSx)). The only "problem" here is that
CALLER_ADDRESSx for x > 1 returns NULL which doesn't do much harm.
The drawback of implementing a fix (i.e. use unwind tables to implement CALLER_ADDRESSx) is that much of the unwinder code would need to be marked as not
traceable.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Syntactically FOOTBRIDGE and ARCH_FOOTBRIDGE are identical (the former
is defined in an if ARCH_FOOTBRIDGE block and the latter selects the
former).
Sematically FOOTBRIDGE means "we have a DC21285 (aka footbridge) device
in the system" and ARCH_FOOTBRIDGE is the support for boards with a
footbridge device, so ARCH_FOOTBRIDGE is the better symbol here.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With compilers which follow the C99 standard (like modern versions of gcc and
clang), "extern inline" does the wrong thing (emits code for an externally
linkable version of the inline function). In this case using static inline
and removing the NULL version of return_address in return_address.c does
the right thing.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Reviewed-by: Mark Charlebois <charlebm@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sigpage is currently placed alongside shared libraries etc in the
address space. Similar to what x86_64 does for its VDSO, place the
sigpage at a randomized offset above the stack so that learning the
base address of the sigpage doesn't help expose where shared libraries
are loaded in the address space (and vice versa).
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
_install_special_mapping allows the VMA to be identifed in
/proc/pid/maps without the use of arch_vma_name, providing a
slight net reduction in object size:
text data bss dec hex filename
2996 96 144 3236 ca4 arch/arm/kernel/process.o (before)
2956 104 144 3204 c84 arch/arm/kernel/process.o (after)
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable gcov support for ARM based on original patches by David
Singleton and George G. Davis
Riku - updated to patch to current mainline kernel. The patch
has been submitted in 2010, 2012 - for symmetry, now in 2014 too.
https://lwn.net/Articles/390419/http://marc.info/?l=linux-arm-kernel&m=133823081813044
v2: remove arch/arm/kernel from gcov disabled files
Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Vincent Sanders <vincent.sanders@collabora.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If we are not changing the control register value, avoid writing to it.
Writes to the control register can be very expensive, taking around a
hundred cycles or so.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the more common pr_warn.
Other miscellanea:
o Coalesce formats
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When we catch something that's not a permission fault or a translation
fault, we log the unsupported FSC in the kernel log, but we were masking
off the bottom bits of the FSC which was not very helpful.
Also correctly report the FSC for data and instruction faults rather
than telling people it was a DFCS, which doesn't exist in the ARM ARM.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The current aarch64 calculation for VTTBR_BADDR_MASK masks only 39 bits
and not all the bits in the PA range. This is clearly a bug that
manifests itself on systems that allocate memory in the higher address
space range.
[ Modified from Joel's original patch to be based on PHYS_MASK_SHIFT
instead of a hard-coded value and to move the alignment check of the
allocation to mmu.c. Also added a comment explaining why we hardcode
the IPA range and changed the stage-2 pgd allocation to be based on
the 40 bit IPA range instead of the maximum possible 48 bit PA range.
- Christoffer ]
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Joel Schopp <joel.schopp@amd.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Apparently most of the newly added nodes had the same problem,
so instead of reverting the individual patches, this undoes
the effect of the merge and backs out all of them at once.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Two of the recent patches each added support for CPU_FREQ, which
causes a kconfig warning:
arch/arm/configs/multi_v7_defconfig:443:warning: override: reassigning to symbol CPU_FREQ
This removes one of the two in order to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The newly introduced support for SAMA5D4 added access to the
'AT91_ALT_BASE_SYS' register area, but failed to define the
symbols in the case when CONFIG_MMU is disabled.
We really should not hardwire addresses like this any more,
but as a small fixup, this patch just adds the missing
definitions for the nommu case, which gets at91x40_defconfig
and any configuration of sam9 and sama5 with MMU disabled
back to work.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 726d32bf79 ("ARM: at91: SAMA5D4 SoC detection code and low ...")
Every mcount() call in the MIPS 32-bit kernel is done as follows:
[...]
move at, ra
jal _mcount
addiu sp, sp, -8
[...]
but upon returning from the mcount() function, the stack pointer
is not adjusted properly. This is explained in details in 58b69401c7
(MIPS: Function tracer: Fix broken function tracing).
Commit ad8c396936 ("MIPS: Unbreak function tracer for 64-bit kernel.)
fixed the stack manipulation for 64-bit but it didn't fix it completely
for MIPS32.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7792/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit bbd426f542 "MIPS: Simplify FP context access" modified the
SIFROMREG & SIFROMHREG macros such that they return unsigned rather
than signed 32b integers. I had believed that to be fine, but
inadvertently missed the MFC1 & MFHC1 cases which write to a struct
pt_regs regs element. On MIPS32 this is fine, but on 64 bit those
saved regs' fields are 64 bit wide. Using unsigned values caused the
32 bit value from the FP register to be zero rather than sign extended
as the architecture specifies, causing incorrect emulation of the
MFC1 & MFHc1 instructions. Fix by reintroducing the casts to signed
integers, and therefore the sign extension.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: stable@vger.kernel.org # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7848/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The symbol is an orphan, get rid of it.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fix spelling typos found in Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Implementing a restart handler in a module don't make sense as there would
be no guarantee that the module is loaded when a restart is needed.
Unexport arm_pm_restart to ensure that no one gets the idea to do it
anyway.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The kernel core now supports a restart handler call chain for system
restart functions.
With this change, the arm_pm_restart callback is now optional, so drop its
initialization and check if it is set before calling it. Only call the
kernel restart handler if arm_pm_restart is not set.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The kernel core now supports a restart handler call chain to restart the
system. Call it if arm_pm_restart is not set.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This reverts commit 610bd8722e.
"ARM: dts: hix5hd2: add wdg node" causes a build breakage due to
an undefined constatns:
Error: arch/arm/boot/dts/hisi-x5hd2.dtsi:374.22-23 syntax error
(Don't you just looove the dtc error messages? They are so informative!)
Signed-off-by: Olof Johansson <olof@lixom.net>
- mmc pinmux for at91sam9263 was missing
- little fix of the old clock implementation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUIvtbAAoJEAf03oE53VmQMP4H/1e3NM8xP6ePHSDzYW/SyqGx
IdFJwRff/FlHTzx23jND6z9SJDLTDu7NhUtABEsOIN+uJ28Vg9FLSR5+XqOfpbGt
UH9M2Xxla0WClIUzNDcDTyX56vo/TT0M1lnfh7IvP4yR0iWghbvDIWj/4L5Zl52n
bU1Ac+Spz4kuSShb6PSLxWfZXY7rlEFZbdOUd0ju2AqgLGbf+GeEWl4JcyPBb0id
MrS2YN5yO+0Ts72QPX7mSDS+RCzTm5ncIw6aLfgJzC0vWWvV6AXn6w6nYNUm/o4+
BlHZLHYOPVOLoz+uQE9biKcWeZhMR1orWkcIGXxfzao2cOm5WGa3CkuLd+dol2g=
=VQv1
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes-non-critical' of git://github.com/at91linux/linux-at91 into next/fixes-non-critical
Pull "Fixes non critical for AT91" from Nicolas Ferre:
- mmc pinmux for at91sam9263 was missing
- little fix of the old clock implementation
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'at91-fixes-non-critical' of git://github.com/at91linux/linux-at91:
ARM: at91/PMC: don't forget to write PMC_PCDR register to disable clocks
ARM: at91: fix at91sam9263ek DT mmc pinmuxing settings
The ASM below does not compile with clang and is not the way that the mcr
command is used in other parts of the kernel.
arch/arm/mach-vt8500/vt8500.c:72:11: error: invalid % escape in inline assembly string
asm("mcr%? p15, 0, %0, c7, c0, 4" : : "r" (0));
~~~~~^~~~~~~~~~~~~~~~~~~~~~~~
1 error generated.
There are other forms that are supported on different ARM instruction sets but
generally the kernel just uses mcr as it is supported in all ARM instruction
sets.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Reviewed-by: Mark Charlebois <charlebm@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add all HW-support options from tegra_defconfig that are missing from
multi_v7_defconfig.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- un-use slot-node and deprecate the supports-highspped
for dw-mmc
- remove old USB2 PHY node for exynos5250
- exynos4412-odroid-common
enable PMIC interrupt and i2c improvements
- exynos5250-snow
fold exynos5250-cros-common
update display related nodes
- Peach Pit and Pi
improve power scheme, add support max77802 PMIC,
add hdmi regulators add thermistor, ISL29018 sensor,
set i2c clock at 400kHz, add support Atmel touchpad,
update display related nodes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=aaca
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Pull "Samsung DT update for 3.18" from Kukjin Kim:
- un-use slot-node and deprecate the supports-highspped
for dw-mmc
- remove old USB2 PHY node for exynos5250
- exynos4412-odroid-common
enable PMIC interrupt and i2c improvements
- exynos5250-snow
fold exynos5250-cros-common
update display related nodes
- Peach Pit and Pi
improve power scheme, add support max77802 PMIC,
add hdmi regulators add thermistor, ISL29018 sensor,
set i2c clock at 400kHz, add support Atmel touchpad,
update display related nodes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: remove old USB2 PHY node for exynos5250
ARM: dts: remove old USB2 PHY node hook for exynos5250-arndale
ARM: dts: update display related nodes for exynos5800-peach-pi
ARM: dts: update display related nodes for exynos5420-peach-pit
ARM: dts: update display related nodes for exynos5250-snow
ARM: dts: Add support Atmel touchpad for exynos5800-peach-pi
ARM: dts: Add support Atmel touchpad for exynos5420-peach-pit
ARM: dts: Set i2c7 clock at 400kHz for exynos based Peach boards
ARM: dts: Add ISL29018 sensor for exynos based Peach boards
ARM: dts: Add thermistor dts fragment used by exynos based Peach boards
ARM: dts: add hdmi regulators for exynos5420-peach-pit
ARM: dts: add hdmi regulators for exynos5800-peach-pi
ARM: dts: Add support max77802 PMIC for exynos based Peach boards
ARM: dts: Improve Peach Pit and Pi power scheme
ARM: dts: unuse the slot-node and deprecate the supports-highspeed for dw-mmc in exynos
ARM: dts: Fold exynos5250-cros-common into exynos5250-snow
ARM: dts: Fix MMC pinctrl for exynos5250-snow
ARM: dts: ODROID i2c improvements for exynos4412-odroid-common
ARM: dts: Enable PMIC interrupts for exynos4412-odroid-common
Add dt for rk3288 i2s controller, since i2s clock pins and data pins
default to be GPIO, this patch also add pinctrl to mux them.
Tested on RK3288 board.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- introduction of the new SAMA5D4 SoC and associated Evaluation Kit
- low level soc detection and early printk code
- taking advantage of this, documentation of all AT91 SoC DT strings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUIB6OAAoJEAf03oE53VmQL+IIALNg2XPS49u2Y6VMjL3srFLt
7CUdNoGB7GJKoGrIXPSyAhJLkRlWREgRsEk/RSYqfBpyBZV4PIx9R6dIz1L+VxGU
9neXLkZGrYNzN8qJPz82+ARuCXdCF13N8ClVfXkNDhwbDnlbZgTkh4hNV118mKLt
+PF0d3w354ujieUD7D0pOcdRlny487qMNjtc/0U4P+H2sp2EtL0PpFHicn79InPT
V36PpFtUMEgbw2wQPNtlFkjQWstyZ7WJJGUbIX/2P3PASCwKsgrbmkvDvmfp5tUT
FdclJwJnxgcpni2fDvbz8Vq04i3hixl2Olm8tAvIXOI/hdVcurvZSfweJ5BrfDk=
=fMfO
-----END PGP SIGNATURE-----
Merge tag 'at91-soc2' of git://github.com/at91linux/linux-at91 into next/soc
Pull "Second SoC batch for 3.18" from Nicolas Ferre:
- introduction of the new SAMA5D4 SoC and associated Evaluation Kit
- low level soc detection and early printk code
- taking advantage of this, documentation of all AT91 SoC DT strings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'at91-soc2' of git://github.com/at91linux/linux-at91:
ARM: at91: document Atmel SMART compatibles
ARM: at91: add sama5d4 support to sama5_defconfig
ARM: at91: dt: add device tree file for SAMA5D4ek board
ARM: at91: dt: add device tree file for SAMA5D4 SoC
ARM: at91: SAMA5D4 SoC detection code and low level routines
ARM: at91: introduce basic SAMA5D4 support
clk: at91: add a driver for the h32mx clock
The soc2 branch is based on this cleanup:
* at91/soc:
ARM: at91: Remove the support for the RSI EWS board
ARM: at91: remove board file for Acme Systems Fox G20
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- removal of 2 board C files in mach-at91
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUHFcbAAoJEAf03oE53VmQ1IEH/3Bzs3OhF7YTEM0XX10l64lK
STAVbYurugb6IbvYZ2Q7LY1YOeilaNdZeMmmyivhiIOU5duQURyoSJm1+5VSKF6p
XYZJcJSNdmoqiSTFmmok8sO8CC0Y2hi+W/SgFO/PHnj15PLECX/KddlfMTjRECvr
QvbgruHiX1AX5z5nWyjPFDrxrk33rDvjQfVEqMwjNhcV4hGhV6vU8CIRUrqGftH1
8yGxpGkYYBGlBu6qd9MmgIV0sPmkpMrDaWoEnyphxF8bmZNnkKO0JnxcQCaeHL6v
tQV8EFxQqm5xQU4vNAWnEiDFj/hrZN3fC5tzrOSj8OoEoPIyQW+XKI64Y3UrZXs=
=Q1d3
-----END PGP SIGNATURE-----
Merge tag 'at91-soc' of git://github.com/at91linux/linux-at91 into next/cleanup
Pull "First AT91 SoC batch for 3.18" from Nicolas Ferre:
- removal of 2 board C files in mach-at91
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'at91-soc' of git://github.com/at91linux/linux-at91:
ARM: at91: Remove the support for the RSI EWS board
ARM: at91: remove board file for Acme Systems Fox G20
- Remove unused pieces of the legacy DMA API as we're moving to
dmaengine API
- Search and replace to standardize on pr_warn instead of pr_warning
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUGzmvAAoJEBvUPslcq6Vz53kQAOAS6Rxp03mmjflegqkVzech
JUPBfGQHVwcpbYQU53+ZCt2Bfg0iaD6xL2BtBfS8tsaePDwqT6kVFrDBqWuIiT6S
Taq2NUzqAhdgva74a6VAh0VSpPK4ui3cdXRoXvMfZRvOtR8bbfAprAWYyWipy2RM
4y07a9dcd1SalcWDJttfXxBV7ImqXPf1e6dRtxYRBBshoNJ46/nk8nS9HblaoJbJ
L3FdmOw7x5jG1nSO4dmhsGzg0PmfjKJwe+rGYPVLuEPil6Sc0VDJxGF8ZyAyK+/K
r8ZvIdbWLiJ6ga/ehMNaZaz6sOsSPRAWWSTOOGUlJvBUiOgHH8P+/Y/3fCkcjTlT
Rg15sij0aBVQJNGNEif9xd19f1tnlthSnjIt593YnqElCN50lnNDBt+bVICTlszd
sXbPZtO8vZ0PHEDshBpWvjyPKyN1CrRTVHtGJXZr/zNWoK2Y1NvsdOYR36AlQugW
WhA5hklyJnRpdbiU84fBon9pbowAOIMcLctBqpK5RyqyC+vVgopcaoMWl9F1XW/r
cAcGVm/zAWfWm01XeuJu1R6DOdLxUvi0Sn7UrXcsPwEYR2pp0NdQQUmNEX3Ko9cW
rIO7emEqQvUdY/K+wa5HzhVMHk5VuBIUb8nT30KjOCEGOB7QhEb/6ly6D0pxLFJ0
RtC70hvqxGWawiNpGadr
=ZNTi
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Pull "Clean-up for omaps for v3.18 merge window" from Tony Lindgren:
- Remove unused pieces of the legacy DMA API as we're moving to
dmaengine API
- Search and replace to standardize on pr_warn instead of pr_warning
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'cleanup-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm: mach-omap2: Convert pr_warning to pr_warn
ARM: OMAP: Remove unused pieces of legacy DMA API
start using the SRAM driver for some omaps, and update the
defconfig.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iau9
-----END PGP SIGNATURE-----
Merge tag 'soc-part2-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "part 2 of omap SoC changes" from Tony Lindgren:
Few hwmod changes to support upcoming 8250 driver with DMA,
start using the SRAM driver for some omaps, and update the
defconfig.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'soc-part2-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4+: Remove static iotable mappings for SRAM
ARM: OMAP4+: Move SRAM data to DT
ARM: AM335x: Get rid of unused sram init function
ARM: omap2plus_defconfig: Enable some display features
ARM: omap2plus_defconfig: Enable battery and reset drivers
ARM: omap2plus_defconfig: Add support for distros with systemd
ARM: omap2plus_defconfig: Add cpufreq to defconfig
ARM: omap2plus_defconfig: Shrink with savedefconfig
ARM: OMAP3: Use manual idle for UARTs because of DMA errata
ARM: OMAP2+: Add hwmod flag for HWMOD_RECONFIG_IO_CHAIN
move it to drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cYAz
-----END PGP SIGNATURE-----
Merge tag 'intc-part2-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
Merge "part 2 of omap intc changes" from Tony Lindgren:
Second part of omap intc interrupt controller changes to
move it to drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'intc-part2-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
irqchip: omap-intc: remove unnecessary comments
irqchip: omap-intc: correct maximum number or MIR registers
irqchip: omap-intc: enable TURBO idle mode
irqchip: omap-intc: enable IP protection
irqchip: omap-intc: remove unnecesary of_address_to_resource() call
irqchip: omap-intc: comment style cleanup
irqchip: omap-intc: minor improvement to omap_irq_pending()
arm: omap: irq: move irq.c to drivers/irqchip/
irqchip: add irq-omap-intc.h header
arm: omap2: n8x0: move i2c devices to DT
... for V2M-P1 motherboard CLCD (limited to 640x480 16bpp and using
dedicated video RAM bank) and for V2P-CA9 (up to 1024x768 16bpp).
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "ARM: BCM: Broadcom BCM63138 support" from Florian Fainelli:
This patchset adds very minimal support for the BCM63138 SoC which is
a xDSL SoC using a dual Cortex A9 CPU complex.
* tag 'bcm63138-v4' of http://github.com/brcm/linux:
MAINTAINERS: add entry for the Broadcom BCM63xx ARM SoCs
ARM: BCM63XX: add BCM963138DVT Reference platform DTS
ARM: BCM63XX: add BCM63138 minimal Device Tree
ARM: BCM63XX: add low-level UART debug support
ARM: BCM63XX: add basic support for the Broadcom BCM63138 DSL SoC
Conflicts:
arch/arm/Kconfig.debug
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Max_Read_Request_Size is 3 bits wide, not 2 bits.
Also fix the message.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Without this patch, each root port and the device connected directly to it seem
to be located on a shared (virtual) bus #0. It creates problems with enabling
devices (the PCI code doesn't know that the root bridge must be enabled in order
to access other devices).
The PCIe topology shown by lspci doesn't reflect reality, e.g.:
0000:00:00.0 PCI bridge: Cavium Networks Device 3400
0000:00:01.0 PCI bridge: Texas Instruments XIO2001 PCI Express-to-PCI Bridge
0000:02:...
0001:00:00.0 PCI bridge: Cavium Networks Device 3400 (for the second lane/bus)
-+-[0001:00]---00.0-[01]--
\-[0000:00]-+-00.0-[01]--
| ^^^^ root bridge
\-01.0-[02]----...
^^^^ first external device
With this patch, the first external PCIe device is connected to bus #1
(behind the root bridge).
-+-[0001:00]---00.0-[01]--
\-[0000:00]---00.0-[01-02]----------00.0-[02]----...
^^^^ root bridge ^^^^ first external device
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
UARTs on CNS3xxx are 8250-compatible, not AMBA.
The base address for UART0 is 0x78000000 (physical)
and 0xfb002000 (virtual).
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It broke when host was moved into a separate module, in 47a1685 ("usb:
dwc2/s3c-hsotg: move s3c-hsotg into dwc2 directory"),
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Nothing major, just a few drivers additions and misc options
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+yQb
-----END PGP SIGNATURE-----
Merge tag 'sunxi-defconfig-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/defconfig
Pull "Allwinner defconfig additions for 3.18" from Maxime Ripard
Nothing major, just a few drivers additions and misc options
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'sunxi-defconfig-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi_defconfig: add NLS_CODEPAGE_437 and NLS_ISO8859_1
ARM: sunxi: Add A31 RTC driver to multi_v7_defconfig
ARM: sunxi: Add A31 RTC driver to sunxi_defconfig
* r8a7740: Fix documentation error coppied from elsewhere
* r8a7794: Reserve memory for CMA in a manner consistent to
other R-Car Gen2 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wfDI
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc5-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Pull "Fifth Round of Renesas ARM Based SoC Soc Updates for v3.18" from Simon Horman:
* r8a7740: Fix documentation error copied from elsewhere
* r8a7794: Reserve memory for CMA in a manner consistent to
other R-Car Gen2 SoCs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'renesas-soc5-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7740 legacy: Fix copied bug in comment
ARM: shmobile: r8a7794: Reserve memory as other R-Car Gen2 SoCs
Support is enabled for Venice2's touchpad, and Tegra124's AHCI (SATA)
controller, as used on Jetson TK1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cO5m
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.18-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/defconfig
Pull "ARM: tegra: tegra_defconfig changes for 3.18" from Stephen Warren:
Support is enabled for Venice2's touchpad, and Tegra124's AHCI (SATA)
controller, as used on Jetson TK1.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'tegra-for-3.18-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: enable Atmel touchpad in defconfig
ARM: tegra: Add options for Tegra AHCI support to tegra_defconfig
Contains an update to 3.17-rc2.
The main highlights are:
* SATA and PCIe support added to Tegra124, and enabled on Jetson TK1.
* Touchpad enabled on Venice2 (although the driver still has a few issues
to be worked out).
* NVIDIA reference boards rely on the bootloader to program the pinmux.
* Support added for the Acer Chromebook 13 (CB5).
* DT nodes added for the Tegra flow controller HW module. This will
help reduce use of iomap.h in a future code cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=X2mr
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.18-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
Pull "ARM: tegra: device tree changes for 3.18" from Stephen Warren:
The main highlights are:
* SATA and PCIe support added to Tegra124, and enabled on Jetson TK1.
* Touchpad enabled on Venice2 (although the driver still has a few issues
to be worked out).
* NVIDIA reference boards rely on the bootloader to program the pinmux.
* Support added for the Acer Chromebook 13 (CB5).
* DT nodes added for the Tegra flow controller HW module. This will
help reduce use of iomap.h in a future code cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'tegra-for-3.18-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: enable PCIe in Jetson TK1 DT
ARM: tegra: add PCIe to Tegra124 DT
ARM: tegra: rely on bootloader pinmux programming on Tegra124
ARM: tegra: add Acer Chromebook 13 device tree
ARM: tegra: Move pwm and dpaux labels to tegra124.dtsi
ARM: tegra: add touchpad to Venice2 DT
ARM: tegra: Add device tree nodes for flow controller
ARM: tegra: add PCIe-related pins to the Jetson TK1 pinmux tables
ARM: tegra: Add SATA and SATA power to Jetson TK1 device tree
ARM: tegra: Add SATA controller to Tegra124 device tree
the primary change here gets its address information from DT rather than
iomap.h. This removes one more user of iomap.h, and will help allow the
code to move to a location that can be shared between arch/arm and
arch/arm64.
An unused header file was also removed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BeSe
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.18-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
Pull "ARM: tegra: core SoC code changes for 3.18" from Stephen Warren:
the primary change here gets its address information from DT rather than
iomap.h. This removes one more user of iomap.h, and will help allow the
code to move to a location that can be shared between arch/arm and
arch/arm64.
An unused header file was also removed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'tegra-for-3.18-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: remove unused tegra_emc.h
ARM: tegra: Initialize flow controller from DT
of: Add NVIDIA Tegra flow controller bindings
- specify DMA channels for USART on sama5d3 and choose peripherals
that will use them on the EK boards
- SSC update for audio on at91sam9rl and at91sam9g20
- addition of the NFC clock and new pinctrl compatible string
to use enhancements that will land in drivers during this release
- several new nodes and fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUGxCuAAoJEAf03oE53VmQDRYIAIMkFVY9ZfhVDD8BEwOXm5FL
ZECxGAKxzoaN+P5DbDOqCWmW9juxLhJjxPrwmpoYi7ShG5exYGl2jUZiF6fRq/fH
JJgSNKuNCLJbwlVWBo150v+2gRTyew3Pt8ijZWkzK06YPjW8Oxy3c4MjZ+wF2838
k9jv/8dMT52nEr24x9Py0CPYR1Dh+EzFfoIXyJ4XM66CPIFfn4Ds4tz2gRhj7t2Z
8NyGJ/F+fP3HB1ds3nauaS77XkulN5R/odIQchUzu4IO+mEQY9pbeVvyXWv97Y5T
gL9AE5hcSwnE2xrXJGt2l2HV90FZMFU108WIKucca+RPOlfaB25fpMvMm8gAxDA=
=fE/3
-----END PGP SIGNATURE-----
Merge tag 'at91-dt3' of git://github.com/at91linux/linux-at91 into next/dt
Pull "More AT91 DT material for 3.18" from Nicolas Ferre:
- specify DMA channels for USART on sama5d3 and choose peripherals
that will use them on the EK boards
- SSC update for audio on at91sam9rl and at91sam9g20
- addition of the NFC clock and new pinctrl compatible string
to use enhancements that will land in drivers during this release
- several new nodes and fixes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'at91-dt3' of git://github.com/at91linux/linux-at91:
ARM: at91/dt: at91sam9m10g45ek add rtc node
ARM: at91/dt: sama5d3: use new pinctrl compatible string
ARM: at91/dt: sama5d3: add the nfc clock
ARM: at91/dt: declare sckc node on at91sam9g45
ARM: at91/dt: Fix typo regarding can0_clk
ARM: at91/dt: at91sam9g20: switch ssc compatible string
ARM: at91/dt: at91sam9rl: switch ssc compatible string
ARM: at91: sama5d3xek: reserve dma channel for audio
ARM: at91: sama5d3: add usart dma configurations
This patch adds the basic machine file for the MesonX SoCs. Only Meson6
is populated.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Meson6 SoC is produced by Amlogic inc. and it is based on 2 Cortex
A9 and an ARM Mali-400 GPU.
This patch adds two basic DTSI for the preliminary support of Meson and
Meson6 SoCs. Another DTS is also added for supporting the atv1200 board,
produced by Geniatech inc.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch updates the multi_v7_defconfig with the CONFIG_* needed by
the just added Meson anch. It also adds a new defconfig specifically for
the Meson SoCs.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the UART definitions needed to support earlyprintk for MesonX SoCs
on UARTAO.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
causing issues for Macbooks and Fedora + Grub2 - Matt Fleming
* Delete the misleading "setup_efi_pci() failed!" message which some
people are seeing when booting EFI - Matt Fleming
* Fix printing strings from the 32-bit EFI boot stub by only passing
32-bit addresses to the firmware - Matt Fleming
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5mVJ
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI fixes from Matt Fleming:
* Revert the static library changes from the merge window since they're
causing issues for Macbooks and Fedora + Grub2 (Matt Fleming)
* Delete the misleading "setup_efi_pci() failed!" message which some
people are seeing when booting EFI (Matt Fleming)
* Fix printing strings from the 32-bit EFI boot stub by only passing
32-bit addresses to the firmware (Matt Fleming)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some of the KGDB macros used for generating the BRK instructions had the
wrong spelling for DBG and KGDB abbreviations.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The alignment fixup incorrectly decodes faulting ARM VLDn/VSTn
instructions (where the optional alignment hint is given but incorrect)
as LDR/STR, leading to register corruption. Detect these and correctly
treat them as unhandled, so that userspace gets the fault it expects.
Reported-by: Simon Hosie <simon.hosie@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SCTLR.HA (hardware access flag) is deprecated and not actually
implemented by any CPUs. Furthermore, it can confuse cr_alignment checks
where the whole value of SCTLR is compared against the value sitting in
the hardware, since the bit is actually RAZ/WI and will not match the
saved cr_alignment value.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Following a recent series of enhancements to the insn code the ARMv8
allnoconfig build has been generating a large number of warnings in the
form of:
arch/arm64/kernel/insn.c:689:8: warning: 'insn' may be used uninitialized in this function [-Wmaybe-uninitialized]
This is because BUG() and related macros can be compiled out so we get
execution paths which normally result in a panic compiling out to noops
instead.
I wasn't able to immediately identify a sensible return value to use in
these cases so just return AARCH64_BREAK_FAULT - this is all "should
never happen" code so hopefully it never has a practical impact.
Signed-off-by: Mark Brown <broonie@kernel.org>
[catalin.marinas@arm.com: AARCH64_BREAK_FAULT definition contributed by Daniel Borkmann]
[catalin.marinas@arm.com: replace return 0 with AARCH64_BREAK_FAULT]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
No need for 3 functions when a single one will do.
Modify the function declaring macros to call the single function.
Reduces object code size a little:
$ size arch/powerpc/platforms/powernv/pci-ioda.o*
text data bss dec hex filename
22303 1073 6680 30056 7568 arch/powerpc/platforms/powernv/pci-ioda.o.new
22840 1121 6776 30737 7811 arch/powerpc/platforms/powernv/pci-ioda.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The return value is unnecessary and unused, so make the functions
void instead of int.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We can unindent the bulk of htab_dt_scan_page_sizes() by returning early
if the property is not found. That is nice in and of itself, but also
has the advantage of making it clear that we always return success once
we have found the ibm,segment-page-sizes property.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At boot we display a bunch of low level settings which can be useful to
know, and can help to spot bugs when things are fundamentally
misconfigured.
At the moment they are very widely spaced, so that we can accommodate
the line:
ppc64_caches.dcache_line_size = 0xYY
But we only print that line when the cache line size is not 128, ie.
almost never, so it just makes the display look odd usually.
The ppc64_caches prefix is redundant so remove it, which means we can
align things a bit closer for the common case. While we're there
replace the last use of camelCase (physicalMemorySize), and use
phys_mem_size.
Before:
Starting Linux PPC64 #104 SMP Wed Aug 6 18:41:34 EST 2014
-----------------------------------------------------
ppc64_pft_size = 0x1a
physicalMemorySize = 0x200000000
ppc64_caches.dcache_line_size = 0xf0
ppc64_caches.icache_line_size = 0xf0
htab_address = 0xdeadbeef
htab_hash_mask = 0x7ffff
physical_start = 0xf000bar
-----------------------------------------------------
After:
Starting Linux PPC64 #103 SMP Wed Aug 6 18:38:04 EST 2014
-----------------------------------------------------
ppc64_pft_size = 0x1a
phys_mem_size = 0x200000000
dcache_line_size = 0xf0
icache_line_size = 0xf0
htab_address = 0xdeadbeef
htab_hash_mask = 0x7ffff
physical_start = 0xf000bar
-----------------------------------------------------
This patch is final, no bike shedding ;)
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We are enabling USB unconditionally which results in following build failure
drivers/built-in.o: In function `tb_drom_read':
(.text+0x1b62b70): undefined reference to `usb_speed_string'
make: *** [vmlinux] Error
Enable USB only if USB_SUPPORT is set to avoid such failures
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Acked-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix the following build failure
drivers/built-in.o: In function `nhi_init':
nhi.c:(.init.text+0x63390): undefined reference to `ehci_init_driver'
by adding a dependency on USB_EHCI_HCD which supplies the ehci_init_driver().
Also we need to depend on USB_OHCI_HCD similarly
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Acked-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
this patches changes some error handling logics in numa_setup_cpu(),
when cpu node is not found, so:
if the cpu is possible, but not present, -1 is kept in numa_cpu_lookup_table,
so later, if the cpu is added, we could set correct numa information for it.
if the cpu is present, then we set the first online node to
numa_cpu_lookup_table instead of 0 ( in case 0 might not be an online node? )
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Acked-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As Nish suggested, it makes more sense to init the numa node informatiion
for present cpus at boottime, which could also avoid WARN_ON(1) in
numa_setup_cpu().
With this change, we also need to change the smp_prepare_cpus() to set up
numa information only on present cpus.
For those possible, but not present cpus, their numa information
will be set up after they are started, as the original code did before commit
2fabf084b6.
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Acked-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Tested-by: Cyril Bur <cyril.bur@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With commit 2fabf084b6 ("powerpc: reorder per-cpu NUMA information's
initialization"), during boottime, cpu_numa_callback() is called
earlier(before their online) for each cpu, and verify_cpu_node_mapping()
uses cpu_to_node() to check whether siblings are in the same node.
It skips the checking for siblings that are not online yet. So the only
check done here is for the bootcpu, which is online at that time. But
the per-cpu numa_node cpu_to_node() uses hasn't been set up yet (which
will be set up in smp_prepare_cpus()).
So I saw something like following reported:
[ 0.000000] CPU thread siblings 1/2/3 and 0 don't belong to the same
node!
As we don't actually do the checking during this early stage, so maybe
we could directly call numa_setup_cpu() in do_init_bootmem().
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Acked-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The size field of the op.type word is now the total number of bytes
to be loaded or stored.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This extends the instruction emulation done by analyse_instr() and
emulate_step() to handle a few more instructions that are found in
the kernel.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This splits out the instruction analysis part of emulate_step() into
a separate analyse_instr() function, which decodes the instruction,
but doesn't execute any load or store instructions. It does execute
integer instructions and branches which can be executed purely by
updating register values in the pt_regs struct. For other instructions,
it returns the instruction type and other details in a new
instruction_op struct. emulate_step() then uses that information
to execute loads, stores, cache operations, mfmsr, mtmsr[d], and
(on 64-bit) sc instructions.
The reason for doing this is so that the KVM code can use it instead
of having its own separate instruction emulation code. Possibly the
alignment interrupt handler could also use this.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit e6a6928c3e "of/fdt: Convert FDT functions to use libfdt",
the kernel stopped supporting old flat device tree formats. The minimum
supported version is now 0x10.
There was a checking function added, early_init_dt_verify(), but it's
not called on powerpc.
The result is, if you boot with an old flat device tree, the kernel will
fail to parse it correctly, think you have no memory etc. and hilarity
ensues.
We can't really fix it, but we can at least catch the fact that the
device tree is in an unsupported format and panic(). We can't call
BUG(), it's too early.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On PowerNV platforms, when a CPU is offline, we put it into nap mode.
It's possible that the CPU wakes up from nap mode while it is still
offline due to a stray IPI. A misdirected device interrupt could also
potentially cause it to wake up. In that circumstance, we need to clear
the interrupt so that the CPU can go back to nap mode.
In the past the clearing of the interrupt was accomplished by briefly
enabling interrupts and allowing the normal interrupt handling code
(do_IRQ() etc.) to handle the interrupt. This has the problem that
this code calls irq_enter() and irq_exit(), which call functions such
as account_system_vtime() which use RCU internally. Use of RCU is not
permitted on offline CPUs and will trigger errors if RCU checking is
enabled.
To avoid calling into any generic code which might use RCU, we adopt
a different method of clearing interrupts on offline CPUs. Since we
are on the PowerNV platform, we know that the system interrupt
controller is a XICS being driven directly (i.e. not via hcalls) by
the kernel. Hence this adds a new icp_native_flush_interrupt()
function to the native-mode XICS driver and arranges to call that
when an offline CPU is woken from nap. This new function reads the
interrupt from the XICS. If it is an IPI, it clears the IPI; if it
is a device interrupt, it prints a warning and disables the source.
Then it does the end-of-interrupt processing for the interrupt.
The other thing that briefly enabling interrupts did was to check and
clear the irq_happened flag in this CPU's PACA. Therefore, after
flushing the interrupt from the XICS, we also clear all bits except
the PACA_IRQ_HARD_DIS (interrupts are hard disabled) bit from the
irq_happened flag. The PACA_IRQ_HARD_DIS flag is set by power7_nap()
and is left set to indicate that interrupts are hard disabled. This
means we then have to ignore that flag in power7_nap(), which is
reasonable since it doesn't indicate that any interrupt event needs
servicing.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
I ran some tests to compare hash_64 using shifts and multiplies.
The results:
POWER6: ~2x slower
POWER7: ~2x faster
POWER8: ~2x faster
Now we have a proper config option, select
CONFIG_ARCH_HAS_FAST_MULTIPLIER on POWER7 and POWER8.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This allows the user to build a kernel targeted at POWER8
(ie gcc -mcpu=power8).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When removing a cpu, this patch makes sure that values
gotten from or passed to firmware are in the correct
endian format.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The ibm,ppc-interrupt-server#s property is in big endian format.
These values need to be converted when used by little endian
architectures.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
of_device_ids (i.e. compatible strings and the respective data) are not
supposed to change at runtime. All functions working with of_device_ids
provided by <linux/of.h> work with const of_device_ids. This allows to
mark all struct of_device_id const, too.
While touching these line also put the __init annotation at the right
position where necessary.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_JUMP_LABEL doesn't ensure HAVE_JUMP_LABEL, if it
is not the case use maintainers's own mutex to guard
the modification of global values.
Signed-off-by: Zhouyi Zhou <yizhouzhou@ict.ac.cn>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A recent patch added a function prototype for htab_remove_mapping in
c code. Fix it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There were a number of prototypes for functions that no longer
exist. Remove them.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix a number of places where global functions were not including
their prototype. This ensures the prototype and the function match.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Simplify things considerably by moving all the ppc32 specific
symbol exports into its own file.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the lib symbol exports closer to their function definitions
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Check that the OPAL_DUMP_READ token exists before initalising the elog
infrastructure.
This avoids littering the OPAL console with:
"OPAL: Called with bad token 91"
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Check that the OPAL_ELOG_READ token exists before initalising the elog
infrastructure.
This avoids littering the OPAL console with:
"OPAL: Called with bad token 74"
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Check that the OPAL_RTC_READ token exists before we use the OPAL RTC.
Refactors the code a little to merge error paths.
This avoids littering the OPAL console with:
"OPAL: Called with bad token 3".
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently there is no way to generically check if an OPAL call exists or not
from the host kernel.
This adds an OPAL call opal_check_token() which tells you if the given token is
present in OPAL or not.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix ppc 32 build failure as reported here:
http://kisskb.ellerman.id.au/kisskb/buildresult/11663513/
The error is as follows:
arch/powerpc/include/asm/floppy.h:142:20: error: 'isa_bridge_pcidev' undeclared
(first use in this function)
This is happening since floppy.o is enabled by BLK_DEV_FD which depends on
ARCH_MAY_HAVE_PC_FDC which is in-turn enabled if PPC_PSERIES=n.
The following commit changes the dependency so that ARCH_MAY_HAVE_PC_FDC is
dependent exclusively on PCI since otherwise it will not compile.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
CC: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
in commit 29f1aff2c (powerpc: Copy bootable images in the default
install script) we changed to copying all the built boot targets based
on the assumption that it's backwards compatible. It turns out that
debian devived installkernel scripts will barf if not given exactly 4
args.
This change reverts make install to just install the vmlinux (we can
change the dfault in a seperate patch) and introduces a new make
zInstall which works with a more flexible installkernel script.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Presently we only support initiating Service Processor dump from host.
Hence update sysfs message. Also update couple of other error/info
messages.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With the introduction of DT based idle states, CPUidle drivers for ARM
can now initialize idle states data through properties in the device tree.
This patch adds code to the big.LITTLE CPUidle driver to dynamically
initialize idle states data through the updated device tree source file.
Cc: Chander Kashyap <k.chander@samsung.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
These are the specific changes for ARM64 to make it possible to integrate the
DT based generic cpuidle driver in this tree.
It contains:
* The documentation for the DT definitions for ARM
* The refactoring of the cpu_suspend function for ARM64
* Introduce the cpu_idle_init function for ARM64
* Add the PSCI CPU SUSPEND based on the previous changes on cpu_suspend
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
New awesome things in this release:
- E500: e6500 core support
- E500: guest and remote debug support
- Book3S: remote sw breakpoint support
- Book3S: HV: Minor bugfixes
Alexander Graf (1):
KVM: PPC: Pass enum to kvmppc_get_last_inst
Bharat Bhushan (8):
KVM: PPC: BOOKE: allow debug interrupt at "debug level"
KVM: PPC: BOOKE : Emulate rfdi instruction
KVM: PPC: BOOKE: Allow guest to change MSR_DE
KVM: PPC: BOOKE: Clear guest dbsr in userspace exit KVM_EXIT_DEBUG
KVM: PPC: BOOKE: Guest and hardware visible debug registers are same
KVM: PPC: BOOKE: Add one reg interface for DBSR
KVM: PPC: BOOKE: Add one_reg documentation of SPRG9 and DBSR
KVM: PPC: BOOKE: Emulate debug registers and exception
Madhavan Srinivasan (2):
powerpc/kvm: support to handle sw breakpoint
powerpc/kvm: common sw breakpoint instr across ppc
Michael Neuling (1):
KVM: PPC: Book3S HV: Add register name when loading toc
Mihai Caraman (10):
powerpc/booke: Restrict SPE exception handlers to e200/e500 cores
powerpc/booke: Revert SPE/AltiVec common defines for interrupt numbers
KVM: PPC: Book3E: Increase FPU laziness
KVM: PPC: Book3e: Add AltiVec support
KVM: PPC: Make ONE_REG powerpc generic
KVM: PPC: Move ONE_REG AltiVec support to powerpc
KVM: PPC: Remove the tasklet used by the hrtimer
KVM: PPC: Remove shared defines for SPE and AltiVec interrupts
KVM: PPC: e500mc: Add support for single threaded vcpus on e6500 core
KVM: PPC: Book3E: Enable e6500 core
Paul Mackerras (2):
KVM: PPC: Book3S HV: Increase timeout for grabbing secondary threads
KVM: PPC: Book3S HV: Only accept host PVR value for guest PVR
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=CR/Z
-----END PGP SIGNATURE-----
Merge tag 'signed-kvm-ppc-next' of git://github.com/agraf/linux-2.6 into kvm-next
Patch queue for ppc - 2014-09-24
New awesome things in this release:
- E500: e6500 core support
- E500: guest and remote debug support
- Book3S: remote sw breakpoint support
- Book3S: HV: Minor bugfixes
Alexander Graf (1):
KVM: PPC: Pass enum to kvmppc_get_last_inst
Bharat Bhushan (8):
KVM: PPC: BOOKE: allow debug interrupt at "debug level"
KVM: PPC: BOOKE : Emulate rfdi instruction
KVM: PPC: BOOKE: Allow guest to change MSR_DE
KVM: PPC: BOOKE: Clear guest dbsr in userspace exit KVM_EXIT_DEBUG
KVM: PPC: BOOKE: Guest and hardware visible debug registers are same
KVM: PPC: BOOKE: Add one reg interface for DBSR
KVM: PPC: BOOKE: Add one_reg documentation of SPRG9 and DBSR
KVM: PPC: BOOKE: Emulate debug registers and exception
Madhavan Srinivasan (2):
powerpc/kvm: support to handle sw breakpoint
powerpc/kvm: common sw breakpoint instr across ppc
Michael Neuling (1):
KVM: PPC: Book3S HV: Add register name when loading toc
Mihai Caraman (10):
powerpc/booke: Restrict SPE exception handlers to e200/e500 cores
powerpc/booke: Revert SPE/AltiVec common defines for interrupt numbers
KVM: PPC: Book3E: Increase FPU laziness
KVM: PPC: Book3e: Add AltiVec support
KVM: PPC: Make ONE_REG powerpc generic
KVM: PPC: Move ONE_REG AltiVec support to powerpc
KVM: PPC: Remove the tasklet used by the hrtimer
KVM: PPC: Remove shared defines for SPE and AltiVec interrupts
KVM: PPC: e500mc: Add support for single threaded vcpus on e6500 core
KVM: PPC: Book3E: Enable e6500 core
Paul Mackerras (2):
KVM: PPC: Book3S HV: Increase timeout for grabbing secondary threads
KVM: PPC: Book3S HV: Only accept host PVR value for guest PVR
If we're executing the 32-bit efi_char16_printk() code path (i.e.
running on top of 32-bit firmware) we know that efi_early->text_output
will be a 32-bit value, even though ->text_output has type u64.
Unfortunately, we currently pass ->text_output directly to
efi_early->call() so for CONFIG_X86_32 the compiler will push a 64-bit
value onto the stack, causing the other parameters to be misaligned.
The way we handle this in the rest of the EFI boot stub is to pass
pointers as arguments to efi_early->call(), which automatically do the
right thing (pointers are 32-bit on CONFIG_X86_32, and we simply ignore
the upper 32-bits of the argument register if running in 64-bit mode
with 32-bit firmware).
This fixes a corruption bug when printing strings from the 32-bit EFI
boot stub.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=84241
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Pull networking fixes from David Miller:
"Here is a quick pull request primarily meant to address the deconfig
fallout from changing SCSI_NETLINK from being used via 'select' to
being used via 'depends'.
I applied a set of 5 patches written by Michal Marek, and then I
carefully audited all of the remaining config files, basically:
1) I scanned every arch config file, and if it mentioned CONFIG_INET
or CONFIG_UNIX, I made sure it had CONFIG_NET=y
2) After that, I scanned every arch config file, and if it did not
have CONFIG_NET=y I made sure it did not reference any networking
config options.
Finally, we have some late breaking wireless fixes in here from John
Linville and co"
[ And there's a sparc bpf fix snuck in too ]
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
sparc: bpf_jit: fix loads from negative offsets
parisc: Update defconfigs which were missing CONFIG_NET.
powerpc: Update defconfigs which were missing CONFIG_NET.
s390: Update defconfigs which were missing CONFIG_NET.
mips: Update some more defconfigs which were missing CONFIG_NET.
sparc: Set CONFIG_NET=y in defconfigs
sh: Set CONFIG_NET=y in defconfigs
powerpc: Set CONFIG_NET=y in defconfigs
parisc: Set CONFIG_NET=y in defconfigs
mips: Set CONFIG_NET=y in defconfigs
brcmfmac: Fix off by one bug in brcmf_count_20mhz_channels()
ath9k: Fix NULL pointer dereference on early irq
net: rfkill: gpio: Fix clock status
NFC: st21nfca: Fix potential depmod dependency cycle
NFC: st21nfcb: Fix depmod dependency cycle
NFC: microread: Potential overflows in microread_target_discovered()
- fix BPF_LD|ABS|IND from negative offsets:
make sure to sign extend lower 32 bits in 64-bit register
before calling C helpers from JITed code, otherwise 'int k'
argument of bpf_internal_load_pointer_neg_helper() function
will be added as large unsigned integer, causing packet size
check to trigger and abort the program.
It's worth noting that JITed code for 'A = A op K' will affect
upper 32 bits differently depending whether K is simm13 or not.
Since small constants are sign extended, whereas large constants
are stored in temp register and zero extended.
That is ok and we don't have to pay a penalty of sign extension
for every sethi, since all classic BPF instructions have 32-bit
semantics and we only need to set correct upper bits when
transitioning from JITed code into C.
- though instructions 'A &= 0' and 'A *= 0' are odd, JIT compiler
should not optimize them out
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
- Device tree support for i.MX ADS and Armadeus APF9328 boards
- Enable thermal sensor support for i.MX6SL
- Add LCD support for i.MX6SL EVK board
- Fix display duplicate name for a bunch of board dts files
- Configure imx6qdl-sabresd board pins locally to remove the dependency
on bootloader
- A set of imx28-tx28 board dts updates from Lothar
- Add pci config space as platform resource
- Enable devices RTC, I2C and HDMI for nitrogen6x board
- Split HummingBoard DT to support s/dl and d/q
- mSATA and IR input support for HummingBoard
- Add SSI baud clock for i.MX6 device trees
- Add USB support for vf610-colibri and vf610-twr boards
- A set of cleanup and updates on Gateworks boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUF7RZAAoJEFBXWFqHsHzOFUgH/i/9xApJoCS4X5HcnS3p0uYO
XLu9qkl4BgvlWTehOQlBBn4Nitv9A2b23BFkZ73+FMiM43NgEXTpitt1oTdO57tA
lmOrtlIeKFGjLLwqBu0WL01VKaH7O6B4Qe09xv/Zx3wz4yYC9l/T23yQ/Z/UFJQT
afqyzMrfzKd0WyE4RsuL/Ir94K9Y0FzWV1u8mhupYlqDdMop27XZRMD2CHs3W9PI
v3c7hjXT4RtLdmvHWUSVg5xwBE7ntYysv7KlEsBebSQ6dkl5vIWDO37yuGQjUAB5
v/Ro63UwM/wPqzq50VESG5c4/OWqz+xLN0r9z+csapDcezO86dCceeek0+qyjvY=
=svCp
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Merge "ARM: imx: device tree changes for 3.18" from Shawn Guo:
The i.MX device tree changes for 3.18:
- Device tree support for i.MX ADS and Armadeus APF9328 boards
- Enable thermal sensor support for i.MX6SL
- Add LCD support for i.MX6SL EVK board
- Fix display duplicate name for a bunch of board dts files
- Configure imx6qdl-sabresd board pins locally to remove the dependency
on bootloader
- A set of imx28-tx28 board dts updates from Lothar
- Add pci config space as platform resource
- Enable devices RTC, I2C and HDMI for nitrogen6x board
- Split HummingBoard DT to support s/dl and d/q
- mSATA and IR input support for HummingBoard
- Add SSI baud clock for i.MX6 device trees
- Add USB support for vf610-colibri and vf610-twr boards
- A set of cleanup and updates on Gateworks boards
* tag 'imx-dt-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (86 commits)
ARM: dts: imx6: make gpt per clock can be from OSC
ARM: dts: imx: ventana: add canbus support for GW52xx
ARM: dts: imx: ventana: cleanup pinctrl groups
ARM: dts: imx: ventana: configure padconf for all pins
ARM: dts: imx: ventana: use gpio constants
ARM: dts: imx: ventana: remove unused aliases
ARM: dts: imx: ventana: remove unsupported dt nodes
ARM: dts: imx28-tx28: add alias for CAN XCVR regulator
ARM: dts: imx28-tx28: add spi-gpio as alternative for spi-mxs
ARM: dts: imx28-tx28: use GPIO flags
ARM: dts: imx28-tx28: remove spidev labels and add third instance of spidev
ARM: dts: imx6sl: add baud clock and clock-names for ssi
ARM: dts: imx6qdl: add baud clock and clock-names for ssi
ARM: dts: imx6qdl-sabresd: Configure the pins locally
ARM: dts: imx28-m28evk: Fix display duplicate name warning
ARM: dts: imx28-tx28: Fix display duplicate name warning
ARM: dts: imx28-m28cu: Fix display duplicate name warning
ARM: dts: imx28-cfa100: Fix display duplicate name warning
ARM: dts: imx28-apf28dev: Fix display duplicate name warning
ARM: dts: imx28-apx4devkit: Fix display duplicate name warning
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add initial devicetree support for i.MX1
- Support GPT per clock source from OSC for i.MX6
- A couple of parent selection corrections for i.MX6SL clock driver
- Support more chip revision for i.MX6
- Convert pr_warning to pr_warn
- Add exclusive gate clock support
- Add BYPASS support for i.MX6 PLL clocks
- Update i.MX6 clock tree for audio use case
- A couple of VF610 clock driver updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUF672AAoJEFBXWFqHsHzOTXQIAJ0ZTXtzQsJ3gLFU+CwRMm2F
hIzFDNOsRkEYpJaa6AkweBmLyUUdePn9rUVRzCi4P9Ux5uCSU6sd3CPHOykOCrV4
xGXk+hL47IpPNGP1tZ4NU7bVBz4BvrIkLRXBxlO+YZ2ZKf+k8Ma166c3iwYFqpDD
8Fd7SQrKleZiXXDgz6y8SRCsOre3HmmjeJBBHhKuegSRscyh2cYfduBsmr6xTojR
Jzcega1pprb1ojxflMVLHcGRquyYVHaoH65mD4leDhSWa93MZFCOAFCl27qsZNs5
gTlaayqq8ws8aFOXi9OmONSjL+ZBMkf0Jk/QGOo5cLCUKYYv10KK2LXFeBOpg8A=
=yLWI
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
Merge "ARM: imx: SoC updates for 3.18" from Shawn Guo:
The i.MX SoC updates for 3.18:
- Add initial devicetree support for i.MX1
- Support GPT per clock source from OSC for i.MX6
- A couple of parent selection corrections for i.MX6SL clock driver
- Support more chip revision for i.MX6
- Convert pr_warning to pr_warn
- Add exclusive gate clock support
- Add BYPASS support for i.MX6 PLL clocks
- Update i.MX6 clock tree for audio use case
- A couple of VF610 clock driver updates
* tag 'imx-soc-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (30 commits)
ARM: imx_v6_v7_defconfig updates
ARM: imx_v4_v5_defconfig: Select CONFIG_IMX_WEIM
arm: mach-imx: Convert pr_warning to pr_warn
ARM: imx: source gpt per clk from OSC for system timer
ARM: imx: add gpt_3m clk for i.mx6qdl
ARM: imx: fix register offset of pll7_usb_host gate clock
ARM: clk-imx6sl: refine clock tree for SSI
ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3 driver
ARM: imx6sx: add BYPASS support for PLL clocks
ARM: imx6sl: add BYPASS support for PLL clocks
ARM: imx6q: add BYPASS support for PLL clocks
ARM: imx: add an exclusive gate clock type
ARM: clk-imx6q: refine clock tree for SSI
ARM: clk-imx6q: refine clock tree for ASRC
ARM: clk-imx6sl: correct the pxp and epdc axi clock selections
ARM: clk-imx6q: refine clock tree for ESAI
ARM: clk-imx6sl: Select appropriate parents for LCDIF clocks
ARM: clk-imx6sl: Remove csi_lcdif_sels[]
ARM: imx: clk-vf610: Add USBPHY clocks
ARM: imx: add cpufreq support for i.mx6sx
...
Signed-off-by: Olof Johansson <olof@lixom.net>
* Enable r8a7794 SoC in shmobile_defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JqYw
-----END PGP SIGNATURE-----
Merge tag 'renesas-defconfig4-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/defconfig
Merge "Fourth Round of Renesas ARM Based SoC Defconfig Updates for v3.18" from Simon Horman:
Fourth Round of Renesas ARM Based SoC Defconfig Updates for v3.18
* Enable r8a7794 SoC in shmobile_defconfig
* tag 'renesas-defconfig4-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Enable r8a7794 SoC in shmobile_defconfig
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable Mediatek platform support for multi_v7_defconfig.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch changes the compatible string of the GIC to the
new "arm,cortex-a7-gic" which does reflect the actual hardware.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the missing 'compatible' property to device tree root node of
- mt6589-aquaris5.dts
and document the new values.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add boot argument for earlyprintk to the aquaris5 device tree file.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This changes the unit address of the gic node to it's first register area.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This allows the "make dtbs" to build the aquaris5 dtb for the Mediatek
SoC.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
- Armada 375
- Add RTC support
- Armada 370
- Add proper pinmuxing
- Add SSCG
- Add gpio-fan
- Add LED support
- change Intersil vendor prefix to isil
- use improved Armada SPI compatible string
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=rLx3
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-3.18' of git://git.infradead.org/linux-mvebu into next/dt
Merge "ARM: mvebu: DT changes for v3.18" from Jason Cooper:
mvebu DT changes for v3.18
- Armada 375
- Add RTC support
- Armada 370
- Add proper pinmuxing
- Add SSCG
- Add gpio-fan
- Add LED support
- change Intersil vendor prefix to isil
- use improved Armada SPI compatible string
* tag 'mvebu-dt-3.18' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add user LED support of Armada 370 RD
ARM: mvebu: add gpio fan support to Armada 370 RD
ARM: mvebu: Change vendor prefix for Intersil Corporation to isil
ARM: mvebu: use improved armada spi device tree compatible name
ARM: mvebu: add SSCG to Armada 370 Device Tree
ARM: mvebu: Add proper pin muxing on Armada 370 RD board
ARM: mvebu: Add proper pin muxing on Netgear ReadyNAS 104
ARM: mvebu: Add proper pin muxing on Netgear ReadyNAS 102
ARM: mvebu: Add proper pin muxing on the Armada 370 DB board
ARM: mvebu: Add proper pin muxing on Globalscale Mirabox board
ARM: mvebu: Add network pin mux configuration for the Armada 370 SoC
ARM: mvebu: Add RTC support for Armada 375
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-mips@linux-mips.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compiling with "ARCH=arm" and "allmodconfig",
with commit: 9cdc99919a [2/7] ARM: hisi: enable MCPM implementation
we will get:
/tmp/cc6DjYjT.s: Assembler messages:
/tmp/cc6DjYjT.s:63: Error: selected processor does not support ARM mode `ubfx r1,r0,#8,#8'
/tmp/cc6DjYjT.s:761: Error: selected processor does not support ARM mode `isb '
/tmp/cc6DjYjT.s:762: Error: selected processor does not support ARM mode `dsb '
/tmp/cc6DjYjT.s:769: Error: selected processor does not support ARM mode `isb '
/tmp/cc6DjYjT.s:775: Error: selected processor does not support ARM mode `isb '
/tmp/cc6DjYjT.s:776: Error: selected processor does not support ARM mode `dsb '
/tmp/cc6DjYjT.s:795: Error: selected processor does not support ARM mode `isb '
/tmp/cc6DjYjT.s:801: Error: selected processor does not support ARM mode `isb '
/tmp/cc6DjYjT.s:802: Error: selected processor does not support ARM mode `dsb '
Fix platmcpm compilation when ARMv6 is selected.
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This is to receive 0a30288da1 ("blk-mq, percpu_ref: implement a
kludge for SCSI blk-mq stall during probe") which implements
__percpu_ref_kill_expedited() to work around SCSI blk-mq stall. The
commit reverted and patches to implement proper fix will be added.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Pull crypto fixes from Herbert Xu:
"This fixes three issues:
- if ccp is loaded on a machine without ccp, it will incorrectly
activate causing all requests to fail. Fixed by preventing ccp
from loading if hardware isn't available.
- not all IRQs were enabled for the qat driver, leading to potential
stalls when it is used
- disabled buggy AVX CTR implementation in aesni"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: aesni - disable "by8" AVX CTR optimization
crypto: ccp - Check for CCP before registering crypto algs
crypto: qat - Enable all 32 IRQs
When introducing support for sama5d3, the write to PMC_PCDR register has
been accidentally removed.
Reported-by: Nathalie Cyrille <nathalie.cyrille@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> # 3.10.x and later
As discovered on a custom board similar to at91sam9263ek and basing
its devicetree on that one apparently the pin muxing doesn't get
set up properly. This was discovered since the custom boards u-boot
does funky stuff with the pin muxing and leaved it set to SPI
which made the MMC driver not work under Linux.
The fix is simply to define the given configuration as the default.
This probably worked by pure luck before, but it's better to
make the muxing explicitly set.
Signed-off-by: Andreas Henriksson <andreas.henriksson@endian.se>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> # 3.11+
per_cpu_load_addr is only used for 64-bit relocations, but is
declared in both configurations of relocs.c - with different
types. This has undefined behaviour in general. GNU ld is
documented to use the larger size in this case, but other tools
may differ and some warn about this.
References: https://bugs.debian.org/748577
Reported-by: Michael Tautschnig <mt@debian.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: 748577@bugs.debian.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1411561812.3659.23.camel@decadent.org.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Trivial. We have "lib-y += thunk_$(BITS).o" at the start, no
need to add thunk_64.o if !CONFIG_X86_32.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140921184232.GB23727@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
___preempt_schedule() does SAVE_ALL/RESTORE_ALL but this is
suboptimal, we do not need to save/restore the callee-saved
register. And we already have arch/x86/lib/thunk_*.S which
implements the similar asm wrappers, so it makes sense to
redefine ___preempt_schedule() as "THUNK ..." and remove
preempt.S altogether.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Andy Lutomirski <luto@amacapital.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140921184153.GA23727@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The "by8" implementation introduced in commit 22cddcc7df ("crypto: aes
- AES CTR x86_64 "by8" AVX optimization") is failing crypto tests as it
handles counter block overflows differently. It only accounts the right
most 32 bit as a counter -- not the whole block as all other
implementations do. This makes it fail the cryptomgr test #4 that
specifically tests this corner case.
As we're quite late in the release cycle, just disable the "by8" variant
for now.
Reported-by: Romain Francoise <romain@orebokech.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Chandramouli Narayanan <mouli@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The following bug can be triggered by hot adding and removing a large number of
xen domain0's vcpus repeatedly:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000004 IP: [..] find_busiest_group
PGD 5a9d5067 PUD 13067 PMD 0
Oops: 0000 [#3] SMP
[...]
Call Trace:
load_balance
? _raw_spin_unlock_irqrestore
idle_balance
__schedule
schedule
schedule_timeout
? lock_timer_base
schedule_timeout_uninterruptible
msleep
lock_device_hotplug_sysfs
online_store
dev_attr_store
sysfs_write_file
vfs_write
SyS_write
system_call_fastpath
Last level cache shared mask is built during CPU up and the
build_sched_domain() routine takes advantage of it to setup
the sched domain CPU topology.
However, llc_shared_mask is not released during CPU disable,
which leads to an invalid sched domainCPU topology.
This patch fix it by releasing the llc_shared_mask correctly
during CPU disable.
Yasuaki also reported that this can happen on real hardware:
https://lkml.org/lkml/2014/7/22/1018
His case is here:
==
Here is an example on my system.
My system has 4 sockets and each socket has 15 cores and HT is
enabled. In this case, each core of sockes is numbered as
follows:
| CPU#
Socket#0 | 0-14 , 60-74
Socket#1 | 15-29, 75-89
Socket#2 | 30-44, 90-104
Socket#3 | 45-59, 105-119
Then llc_shared_mask of CPU#30 has 0x3fff80000001fffc0000000.
It means that last level cache of Socket#2 is shared with
CPU#30-44 and 90-104.
When hot-removing socket#2 and #3, each core of sockets is
numbered as follows:
| CPU#
Socket#0 | 0-14 , 60-74
Socket#1 | 15-29, 75-89
But llc_shared_mask is not cleared. So llc_shared_mask of CPU#30
remains having 0x3fff80000001fffc0000000.
After that, when hot-adding socket#2 and #3, each core of
sockets is numbered as follows:
| CPU#
Socket#0 | 0-14 , 60-74
Socket#1 | 15-29, 75-89
Socket#2 | 30-59
Socket#3 | 90-119
Then llc_shared_mask of CPU#30 becomes
0x3fff8000fffffffc0000000. It means that last level cache of
Socket#2 is shared with CPU#30-59 and 90-104. So the mask has
the wrong value.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Tested-by: Linn Crosetto <linn@hp.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1411547885-48165-1-git-send-email-wanpeng.li@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With certain kernel configurations, CPU offline consumes more than
100ms during S3.
It's a timing related issue: native_cpu_die() would occasionally fall
into a 100ms sleep when the CPU idle loop thread marked the CPU state
to DEAD too slowly.
What native_cpu_die() does is that it polls the CPU state and waits
for 100ms if CPU state hasn't been marked to DEAD. The 100ms sleep
doesn't make sense and is purely historic.
To avoid such long sleeping, this patch adds a 'struct completion'
to each CPU, waits for the completion in native_cpu_die() and wakes
up the completion when the CPU state is marked to DEAD.
Tested on an Intel Xeon server with 48 cores, Ivybridge and on
Haswell laptops. The CPU offlining cost on these machines is
reduced from more than 100ms to less than 5ms. The system
suspend time is reduced by 2.3s on the servers.
Borislav and Prarit also helped to test the patch on an AMD
machine and a few systems of various sizes and configurations
(multi-socket, single-socket, no hyper threading, etc.). No
issues were seen.
Tested-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: srostedt@redhat.com
Cc: toshi.kani@hp.com
Cc: imammedo@redhat.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1409039025-32310-1-git-send-email-tianyu.lan@intel.com
[ Improved a few minor details in the code, cleaned up the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch restructures the memory controller (IMC) uncore PMU support
for client SNB/IVB/HSW processors. The main change is that it can now
cope with more than one PCI device ID per processor model. There are
many flavors of memory controllers for each processor. They have
different PCI device ID, yet they behave the same w.r.t. the memory
controller PMU that we are interested in.
The patch now supports two distinct memory controllers for IVB
processors: one for mobile, one for desktop.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140917090616.GA11281@quad
Cc: ak@linux.intel.com
Cc: kan.liang@intel.com
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The PCU frequency band filters use 8 bit each in a register.
When setting up the value the shift value was not correctly
scaled, which resulted in all filters except for band 0 to
be zero. Fix the scaling.
This allows to correctly monitor multiple uncore frequency bands.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: eranian@google.com
Link: http://lkml.kernel.org/r/1409872109-31645-5-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The IvyBridge-EP uncore driver was missing three filter flags:
NC, ISOC, C6 which are useful in some cases. Support them in the same way
as the Haswell EP driver, by allowing to set them and exposing
them in the sysfs formats.
Also fix a typo in a define.
Relies on the Haswell EP driver to be applied earlier.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1409872109-31645-4-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Current code registers PMUs for all possible uncore pci devices.
This is not good because, on some machines, one or more uncore pci
devices can be missing. The missing pci device make corresponding
PMU unusable. Register the PMU only if the uncore device exists.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: eranian@google.com
Link: http://lkml.kernel.org/r/1409872109-31645-3-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The uncore subsystem in Haswell-EP is similar to Sandy/Ivy
Bridge-EP. There are some differences in config register
encoding and pci device IDs. The Haswell-EP uncore also
supports a few new events. Add the Haswell-EP driver to
the snbep split driver.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
[ Add missing break. Add imc events. Add cbox nc/isoc/c6. ]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: eranian@google.com
Link: http://lkml.kernel.org/r/1409872109-31645-2-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Use the newly added Broadwell cache event list for Haswell too.
All Haswell and Broadwell events and offcore masks used in these lists
are identical.
However Haswell is very different from the Sandy Bridge
list that was used previously. That fixes a wide range of mis-counting
cache events.
The node events are now only for retired memory events, so prefetching
and speculative memory accesses are not included. They are PEBS
capable now, which makes it much easier to sample for them, plus it's
possible to create address maps with -d.
The prefetch events are gone now. They way the hardware counts
them is very misleading (some prefetches included, others not), so
it seemed best to leave them out.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: eranian@google.com
Link: http://lkml.kernel.org/r/1409683455-29168-5-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On Broadwell INST_RETIRED.ALL cannot be used with any period
that doesn't have the lowest 6 bits cleared. And the period
should not be smaller than 128.
Add a new callback to enforce this, and set it for Broadwell.
This is erratum BDM57 and BDM11.
How does this handle the case when an app requests a specific
period with some of the bottom bits set
The apps thinks it is sampling at X occurences per sample, when it is
in fact at X - 63 (worst case).
Short answer:
Any useful instruction sampling period needs to be 4-6 orders
of magnitude larger than 128, as an PMI every 128 instructions
would instantly overwhelm the system and be throttled.
So the +-64 error from this is really small compared to the
period, much smaller than normal system jitter.
Long answer:
<write up by Peter:>
IFF we guarantee perf_event_attr::sample_period >= 128.
Suppose we start out with sample_period=192; then we'll set period_left
to 192, we'll end up with left = 128 (we truncate the lower bits). We
get an interrupt, find that period_left = 64 (>0 so we return 0 and
don't get an overflow handler), up that to 128. Then we trigger again,
at n=256. Then we find period_left = -64 (<=0 so we return 1 and do get
an overflow). We increment with sample_period so we get left = 128. We
fire again, at n=384, period_left = 0 (<=0 so we return 1 and get an
overflow). And on and on.
So while the individual interrupts are 'wrong' we get then with
interval=256,128 in exactly the right ratio to average out at 192. And
this works for everything >=128.
So the num_samples*fixed_period thing is still entirely correct +- 127,
which is good enough I'd say, as you already have that error anyhow.
So no need to 'fix' the tools, al we need to do is refuse to create
INST_RETIRED:ALL events with sample_period < 128.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Maria Dimakopoulou <maria.n.dimakopoulou@gmail.com>
Cc: Mark Davies <junk@eslaf.co.uk>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1409683455-29168-4-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add Broadwell support for Broadwell Client to perf. This is very
similar to Haswell. It uses a new cache event table, because there
were various changes there.
The constraint list has one new event that needs to be handled over
Haswell.
The PEBS event list is the same, so we reuse Haswell's.
[fengguang.wu: make intel_bdw_event_constraints[] static]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: eranian@google.com
Link: http://lkml.kernel.org/r/1409683455-29168-3-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
71 is a Broadwell, not a Haswell. The model number was added
by mistake earlier.
Remove it for now, until it can be re-added later with
real Broadwell support.
In practice it does not cause a lot of issues because the Broadwell
PMU is very similar to Haswell, but some details were wrong,
and it's better to handle it correctly.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: eranian@google.com
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Link: http://lkml.kernel.org/r/1409683455-29168-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I'm getting the spew below when booting with Haswell (Xeon
E5-2699 v3) CPUs and the "Cluster-on-Die" (CoD) feature enabled
in the BIOS. It seems similar to the issue that some folks from
AMD ran in to on their systems and addressed in this commit:
161270fc1f ("x86/smp: Fix topology checks on AMD MCM CPUs")
Both these Intel and AMD systems break an assumption which is
being enforced by topology_sane(): a socket may not contain more
than one NUMA node.
AMD special-cased their system by looking for a cpuid flag. The
Intel mode is dependent on BIOS options and I do not know of a
way which it is enumerated other than the tables being parsed
during the CPU bringup process. In other words, we have to trust
the ACPI tables <shudder>.
This detects the situation where a NUMA node occurs at a place in
the middle of the "CPU" sched domains. It replaces the default
topology with one that relies on the NUMA information from the
firmware (SRAT table) for all levels of sched domains above the
hyperthreads.
This also fixes a sysfs bug. We used to freak out when we saw
the "mc" group cross a node boundary, so we stopped building the
MC group. MC gets exported as the 'core_siblings_list' in
/sys/devices/system/cpu/cpu*/topology/ and this caused CPUs with
the same 'physical_package_id' to not be listed together in
'core_siblings_list'. This violates a statement from
Documentation/ABI/testing/sysfs-devices-system-cpu:
core_siblings: internal kernel map of cpu#'s hardware threads
within the same physical_package_id.
core_siblings_list: human-readable list of the logical CPU
numbers within the same physical_package_id as cpu#.
The sysfs effects here cause an issue with the hwloc tool where
it gets confused and thinks there are more sockets than are
physically present.
Before this patch, there are two packages:
# cd /sys/devices/system/cpu/
# cat cpu*/topology/physical_package_id | sort | uniq -c
18 0
18 1
But 4 _sets_ of core siblings:
# cat cpu*/topology/core_siblings_list | sort | uniq -c
9 0-8
9 18-26
9 27-35
9 9-17
After this set, there are only 2 sets of core siblings, which
is what we expect for a 2-socket system.
# cat cpu*/topology/physical_package_id | sort | uniq -c
18 0
18 1
# cat cpu*/topology/core_siblings_list | sort | uniq -c
18 0-17
18 18-35
Example spew:
...
NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
#2#3#4#5#6#7#8
.... node #1, CPUs: #9
------------[ cut here ]------------
WARNING: CPU: 9 PID: 0 at /home/ak/hle/linux-hle-2.6/arch/x86/kernel/smpboot.c:306 topology_sane.isra.2+0x74/0x90()
sched: CPU #9's mc-sibling CPU #0 is not on the same node! [node: 1 != 0]. Ignoring dependency.
Modules linked in:
CPU: 9 PID: 0 Comm: swapper/9 Not tainted 3.17.0-rc1-00293-g8e01c4d-dirty #631
Hardware name: Intel Corporation S2600WTT/S2600WTT, BIOS GRNDSDP1.86B.0036.R05.1407140519 07/14/2014
0000000000000009 ffff88046ddabe00 ffffffff8172e485 ffff88046ddabe48
ffff88046ddabe38 ffffffff8109691d 000000000000b001 0000000000000009
ffff88086fc12580 000000000000b020 0000000000000009 ffff88046ddabe98
Call Trace:
[<ffffffff8172e485>] dump_stack+0x45/0x56
[<ffffffff8109691d>] warn_slowpath_common+0x7d/0xa0
[<ffffffff8109698c>] warn_slowpath_fmt+0x4c/0x50
[<ffffffff81074f94>] topology_sane.isra.2+0x74/0x90
[<ffffffff8107530e>] set_cpu_sibling_map+0x31e/0x4f0
[<ffffffff8107568d>] start_secondary+0x1ad/0x240
---[ end trace 3fe5f587a9fcde61 ]---
#10#11#12#13#14#15#16#17
.... node #2, CPUs: #18#19#20#21#22#23#24#25#26
.... node #3, CPUs: #27#28#29#30#31#32#33#34#35
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
[ Added LLC domain and s/match_mc/match_die/ ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: brice.goglin@gmail.com
Cc: "H. Peter Anvin" <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/20140918193334.C065EBCE@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The pci_find_bios() function is only ever called from initialization code,
therefore can be marked as such, too. This, in turn, allows marking other
functions called only in this context as well.
The bios32_indirect variable can be marked as __initdata as it is only
referenced from __init functions now.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
The pci_mmcfg_probes[] array is only ever read, therefore make it const.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
The constants in pci_mmcfg_nvidia_mcp55() need to be marked as __initconst
or they will remain in memory after init memory was released.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
According to include/linux/init.h, the __init annotation should be added
immediately before the function name. However, for quite a few functions
in mmconfig-shared.c this is not the case. It's either before the return
type or even in the middle of it. Beside gcc still getting it right, we
should change them to comply to the rules of include/linux/init.h.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
In order to make the APIC access page migratable, stop pinning it in
memory.
And because the APIC access page is not pinned in memory, we can
remove kvm_arch->apic_access_page. When we need to write its
physical address into vmcs, we use gfn_to_page() to get its page
struct, which is needed to call page_to_phys(); the page is then
immediately unpinned.
Suggested-by: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, the APIC access page is pinned by KVM for the entire life
of the guest. We want to make it migratable in order to make memory
hot-unplug available for machines that run KVM.
This patch prepares to handle this for the case where there is no nested
virtualization, or where the nested guest does not have an APIC page of
its own. All accesses to kvm->arch.apic_access_page are changed to go
through kvm_vcpu_reload_apic_access_page.
If the APIC access page is invalidated when the host is running, we update
the VMCS in the next guest entry.
If it is invalidated when the guest is running, the MMU notifier will force
an exit, after which we will handle everything as in the previous case.
If it is invalidated when a nested guest is running, the request will update
either the VMCS01 or the VMCS02. Updating the VMCS01 is done at the
next L2->L1 exit, while updating the VMCS02 is done in prepare_vmcs02.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, the APIC access page is pinned by KVM for the entire life
of the guest. We want to make it migratable in order to make memory
hot-unplug available for machines that run KVM.
This patch prepares to handle this in generic code, through a new
request bit (that will be set by the MMU notifier) and a new hook
that is called whenever the request bit is processed.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will be used to let the guest run while the APIC access page is
not pinned. Because subsequent patches will fill in the function
for x86, place the (still empty) x86 implementation in the x86.c file
instead of adding an inline function in kvm_host.h.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
1. We were calling clear_flush_young_notify in unmap_one, but we are
within an mmu notifier invalidate range scope. The spte exists no more
(due to range_start) and the accessed bit info has already been
propagated (due to kvm_pfn_set_accessed). Simply call
clear_flush_young.
2. We clear_flush_young on a primary MMU PMD, but this may be mapped
as a collection of PTEs by the secondary MMU (e.g. during log-dirty).
This required expanding the interface of the clear_flush_young mmu
notifier, so a lot of code has been trivially touched.
3. In the absence of shadow_accessed_mask (e.g. EPT A bit), we emulate
the access bit by blowing the spte. This requires proper synchronizing
with MMU notifier consumers, like every other removal of spte's does.
Signed-off-by: Andres Lagar-Cavilla <andreslc@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Callbacks don't have to do extra computation to learn what the caller
(lvm_handle_hva_range()) knows very well. Useful for
debugging/tracing/printk/future.
Signed-off-by: Andres Lagar-Cavilla <andreslc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On x86_64, kernel text mappings are mapped read-only with CONFIG_DEBUG_RODATA.
In that case, KVM will fail to patch VMCALL instructions to VMMCALL
as required on AMD processors.
The failure mode is currently a divide-by-zero exception, which obviously
is a KVM bug that has to be fixed. However, picking the right instruction
between VMCALL and VMMCALL will be faster and will help if you cannot upgrade
the hypervisor.
Reported-by: Chris Webb <chris@arachsys.com>
Tested-by: Chris Webb <chris@arachsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Avoid open coded calculations for bank MSRs by using well-defined
macros that hide the index of higher bank MSRs.
No semantic changes.
Signed-off-by: Chen Yucong <slaoub@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 346874c950 ("KVM: x86: Fix CR3 reserved bits") removed non-PAE
reserved bits which were not according to Intel SDM. However, residue was left
in a debug assertion (CR3_NONPAE_RESERVED_BITS). Remove it.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Guest which sets the PAT CR to invalid value should get a #GP. Currently, if
vmx supports loading PAT CR during entry, then the value is not checked. This
patch makes the required check in that case.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In 64-bit mode a #GP should be delivered to the guest "if the code segment
descriptor pointed to by the selector in the 64-bit gate doesn't have the L-bit
set and the D-bit clear." - Intel SDM "Interrupt 13—General Protection
Exception (#GP)".
This patch fixes the behavior of CS loading emulation code. Although the
comment says that segment loading is not supported in long mode, this function
is executed in long mode, so the fix is necassary.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A one-line wrapper around kvm_make_request is not particularly
useful. Replace kvm_mmu_flush_tlb() with kvm_make_request().
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- we count KVM_REQ_TLB_FLUSH requests, not actual flushes
(KVM can have multiple requests for one flush)
- flushes from kvm_flush_remote_tlbs aren't counted
- it's easy to make a direct request by mistake
Solve these by postponing the counting to kvm_check_request().
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Initilization of L2 guest with -cpu host, on L1 guest with -cpu host
triggers:
(qemu) KVM: entry failed, hardware error 0x7
...
nested_vmx_run: VMCS MSR_{LOAD,STORE} unsupported
Nested VMX MSR load/store support is not sufficient to
allow perf for L2 guest.
Until properly fixed, trap CPUID and disable function 0xA.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit fc3a9157d3 ("KVM: X86: Don't report L2 emulation failures to
user-space") disabled the reporting of L2 (nested guest) emulation failures to
userspace due to race-condition between a vmexit and the instruction emulator.
The same rational applies also to userspace applications that are permitted by
the guest OS to access MMIO area or perform PIO.
This patch extends the current behavior - of injecting a #UD instead of
reporting it to userspace - also for guest userspace code.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In init_rmode_tss(), there two variables indicating the return
value, r and ret, and it return 0 on error, 1 on success. The function
is only called by vmx_set_tss_addr(), and ret is redundant.
This patch removes the redundant variable, by making init_rmode_tss()
return 0 on success, -errno on failure.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The KVM emulator code assumes that the guest virtual address space (in 64-bit)
is 48-bits wide. Fail the KVM_SET_CPUID and KVM_SET_CPUID2 ioctl if
userspace tries to create a guest that does not obey this restriction.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A number of people are reporting seeing the "setup_efi_pci() failed!"
error message in what used to be a quiet boot,
https://bugzilla.kernel.org/show_bug.cgi?id=81891
The message isn't all that helpful because setup_efi_pci() can return a
non-success error code for a variety of reasons, not all of them fatal.
Let's drop the return code from setup_efi_pci*() altogether, since
there's no way to process it in any meaningful way outside of the inner
__setup_efi_pci*() functions.
Reported-by: Darren Hart <dvhart@linux.intel.com>
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Cc: Ulf Winkelvos <ulf@winkelvos.de>
Cc: Andre Müller <andre.muller@web.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
* Added APQ8084 dt support for clocks, serial, pinctrl, and IFC6540 board
* Added IPQ8064 dt support for basic SoC and AP148 board
* Added APQ8064 dt support for pinctrl, reset, SDHC, and multimedia clocks
* Added PMIC 8058 dt support on MSM8660, enables PMIC based power key,
keypad, rtc, and vibrator
* Added PMIC 8921 dt support on MSM8960, enables PMIC based power key,
keypad, and rtc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: GPGTools - https://gpgtools.org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=L0k9
-----END PGP SIGNATURE-----
Merge tag 'qcom-dt-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into next/dt
Merge "qcom DT changes for v3.18" from Kumar Gala:
Qualcomm ARM Based Device Tree Updates for v3.18
* Added APQ8084 dt support for clocks, serial, pinctrl, and IFC6540 board
* Added IPQ8064 dt support for basic SoC and AP148 board
* Added APQ8064 dt support for pinctrl, reset, SDHC, and multimedia clocks
* Added PMIC 8058 dt support on MSM8660, enables PMIC based power key,
keypad, rtc, and vibrator
* Added PMIC 8921 dt support on MSM8960, enables PMIC based power key,
keypad, and rtc
* tag 'qcom-dt-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: DT: QCOM: apq8064: Add dma support for sdcc node
ARM: DT: apq8064: Add sdcc support via mcci driver.
ARM: dts: qcom: Add 8064 multimedia clock controller node
ARM: DT: APQ8064: Add node for ps_hold function in pinctrl
ARM: DT: APQ8064: Add pinctrl support
ARM: dts: qcom: Add TLMM DT node for APQ8084
ARM: dts: qcom: Add initial IFC6540 board device tree
ARM: dts: msm: Add 8058 PMIC to ssbi bus
ARM: dts: msm: Add 8921 PMIC to ssbi bus
ARM: qcom: Add initial IPQ8064 SoC and AP148 device trees
ARM: dts: qcom: Add APQ8084 serial port DT node
ARM: dts: qcom: Add APQ8084 Global Clock Controller DT node
Signed-off-by: Olof Johansson <olof@lixom.net>
HIP04 was added out of order, but so was the previous HISI debug uart
support as well. Minor reshuffling of order.
Signed-off-by: Olof Johansson <olof@lixom.net>
- Updates for gta04 to add gta04a3 model
- Add support for Tehnexion TAO3530 boards
- Regulator names for beaglebone
- Pinctrl related updates for omap5, dra7 and am437
- Model name fix for sbc-t54
- Enable mailbox for various omaps
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i9cD
-----END PGP SIGNATURE-----
Merge tag 'dt-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap dts changes for v3.18 merge window" from Tony Lindgren:
Changes for .dts files for omaps for v3.18 merge window:
- Updates for gta04 to add gta04a3 model
- Add support for Tehnexion TAO3530 boards
- Regulator names for beaglebone
- Pinctrl related updates for omap5, dra7 and am437
- Model name fix for sbc-t54
- Enable mailbox for various omaps
* tag 'dt-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (291 commits)
ARM: dts: OMAP2+: Add sub mailboxes device node information
ARM: dts: dra7-evm: Mark uart1 rxd as wakeup capable
ARM: dts: OMAP5 / DRA7: switch over to interrupts-extended property for UART
ARM: dts: AM437x: switch to compatible pinctrl
ARM: dts: DRA7: switch to compatible pinctrl
ARM: dts: OMAP5: switch to compatible pinctrl
ARM: dts: am335x-boneblack: Add names for remaining regulators
ARM: dts: sbc-t54: fix model property
ARM: dts: omap5.dtsi: add DSS RFBI node
ARM: dts: omap3: Add HEAD acoustics omap3-ha.dts and omap3-ha-lcd.dts (TAO3530 based)
ARM: dts: omap3: Add Technexion Thunder support (TAO3530 SOM based)
ARM: dts: omap3: Add Technexion TAO3530 SOM omap3-tao3530.dtsi
ARM: OMAP2+: tao3530: Add pdata-quirk for the mmc2 internal clock
ARM: OMAP2+: board-generic: add support for AM57xx family
ARM: dts: dra72-evm: Add tps65917 PMIC node
ARM: dts: dra72-evm: Enable I2C1 node
Linux 3.17-rc3
unicore32: Fix build error
vexpress/spc: fix a build warning on array bounds
spi: sh-msiof: Fix transmit-only DMA transfers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
it ready to move to drivers/irqchip. Note that this series
does not yet move the interrupt code to drivers, that will
be posted separately as a follow-up series.
Note that this branch has a dependency to patches both
in fixes-v3.18-not-urgent and soc-for-v3.18 and is based on
a merge. Without doing the merge, off-idle would not work
properly for git bisect.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=M+BY
-----END PGP SIGNATURE-----
Merge tag 'intc-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
Merge "omap intc changes for v3.18 merge window" from Tony Lindgren:
Interrupt code related clean-up for omap2 and 3 to make
it ready to move to drivers/irqchip. Note that this series
does not yet move the interrupt code to drivers, that will
be posted separately as a follow-up series.
Note that this branch has a dependency to patches both
in fixes-v3.18-not-urgent and soc-for-v3.18 and is based on
a merge. Without doing the merge, off-idle would not work
properly for git bisect.
* tag 'intc-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (325 commits)
arm: omap: intc: switch over to linear irq domain
arm: omap: irq: get rid of ifdef hack
arm: omap: irq: introduce omap_nr_pending
arm: omap: irq: remove nr_irqs argument
arm: omap: irq: remove unnecessary header
arm: omap: irq: drop omap2_intc_handle_irq()
arm: omap: irq: drop omap3_intc_handle_irq()
arm: omap: irq: call set_handle_irq() from .init_irq
arm: omap: irq: move some more code around
arm: boot: dts: omap2/3/am33xx: drop ti,intc-size
arm: omap: irq: drop ti,intc-size support
arm: boot: dts: am33xx/omap3: fix intc compatible flag
arm: omap: irq: use compatible flag to figure out number of IRQ lines
arm: omap: irq: add specific compatibles for omap3 and am33xx devices
arm: omap: irq: drop .handle_irq and .init_irq fields
arm: omap: irq: use IRQCHIP_DECLARE macro
arm: omap: irq: call set_handle_irq() from intc_of_init
arm: omap: irq: make intc_of_init static
arm: omap: irq: reorganize code a little bit
arm: omap: irq: always define omap3 support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- PM changes to make the code easier to use on newer SoCs
- PM changes for newer SoCs suspend and resume and wake-up events
- Minor clean-up to remove dead Kconfig options
Note that these have a dependency to the fixes-v3.18-not-urgent
tag and is based on a commit in that series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LW8C
-----END PGP SIGNATURE-----
Merge tag 'soc-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
SoC related changes for omaps for v3.18 merge window:
- PM changes to make the code easier to use on newer SoCs
- PM changes for newer SoCs suspend and resume and wake-up events
- Minor clean-up to remove dead Kconfig options
Note that these have a dependency to the fixes-v3.18-not-urgent
tag and is based on a commit in that series.
* tag 'soc-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (514 commits)
ARM: OMAP5+: Reuse OMAP4 PM code for OMAP5 and DRA7
ARM: dts: OMAP3+: Add PRM interrupt
ARM: omap: Remove stray ARCH_HAS_OPP references
ARM: DRA7: Add hook in SoC initcalls to enable pm initialization
ARM: OMAP5: Add hook in SoC initcalls to enable pm initialization
ARM: OMAP5 / DRA7: Enable CPU RET on suspend
ARM: OMAP5 / DRA7: PM: Provide a dummy startup function for CPU hotplug
ARM: OMAP5 / DRA7: PM: Avoid all SAR saves
ARM: OMAP5 / DRA7: PM: Enable Mercury retention mode on CPUx powerdomains
ARM: OMAP5 / DRA7: PM / wakeupgen: Enables ES2 PM mode by default
ARM: OMAP5 / DRA7: PM: Set MPUSS-EMIF clock-domain static dependency
ARM: OMAP5 / DRA7: PM: Update CPU context register offset
ARM: AM437x: use pdata quirks for pinctrl information
ARM: DRA7: use pdata quirks for pinctrl information
ARM: OMAP5: use pdata quirks for pinctrl information
ARM: OMAP4+: PM: Use only valid low power state for CPU hotplug
ARM: OMAP4+: PM: use only valid low power state for suspend
ARM: OMAP4+: PM: Make logic state programmable
ARM: OMAP2+: powerdomain: introduce logic for finding valid power domain
ARM: OMAP2+: powerdomain: pwrdm_for_each_clkdm iterate only valid clkdms
...
for the -rc cycle:
- Fixes for .dts files to differentiate panda and beaglebone versions
- Powerdomain fixes from Nishant Menon mostly for newer omaps
- Fixes for __initconst and of_device_ids const usage
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RPuM
-----END PGP SIGNATURE-----
Merge tag 'fixes-v3.18-not-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "non-urgent omap fixes for v3.18 merge window" from Tony Lindgren:
Fixes for omaps that were not considered urgent enough
for the -rc cycle:
- Fixes for .dts files to differentiate panda and beaglebone versions
- Powerdomain fixes from Nishant Menon mostly for newer omaps
- Fixes for __initconst and of_device_ids const usage
* tag 'fixes-v3.18-not-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: make of_device_ids const
ARM: omap2: make arrays containing machine compatible strings const
ARM: OMAP4+: PM: Use only valid low power state for CPU hotplug
ARM: OMAP4+: PM: use only valid low power state for suspend
ARM: OMAP4+: PM: Make logic state programmable
ARM: OMAP2+: powerdomain: introduce logic for finding valid power domain
ARM: OMAP2+: powerdomain: pwrdm_for_each_clkdm iterate only valid clkdms
ARM: OMAP5: powerdomain data: fix powerdomain powerstate
ARM: OMAP: DRA7: powerdomain data: fix powerdomain powerstate
ARM: dts: am335x-bone*: Fix model name and update compatibility information
ARM: dts: omap4-panda: Fix model and SoC family details
+ Linux 3.17-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
- move of the PIT (basic timer) from mach-at91 to its proper location:
drivers/clocksource
- big cleanup of this driver along the way
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUFw4gAAoJEAf03oE53VmQAdwH+gIVjFww5vGjvfZqcOofmjlA
hzELgv1Jem2/OSQRkKX9ekY0hArca7POij+V9Ubz0LHag8JzEXhORq7KThx6vXbY
iUtx5hXkyXded5h8WqDJT0y7YFpM57Hv6Dgp7gXJQnNULwhQnafds0ucKr0fZVZK
64Zhf6YDQnHYotEoiE2zi+yAl2BI9uoO2tP+kWPezNWLQ5v89FnWtt828N+5Be/B
gujSX1ZHDtsIshdfjqhlZtm1eGDztajm/OxdWheU4qELsZ5QaSYe3klaExV93Hp4
LCFzczu54/krauAlLn01x/Kyjpi8S8Hc4Qj6AQU8LpAvoy/SMBy9xo0SIlX1ZX4=
=Zxt2
-----END PGP SIGNATURE-----
Merge tag 'at91-drivers2' of git://github.com/at91linux/linux-at91 into next/drivers
Merge " Second drivers series for AT91/3.18" from Nicolas Ferre:
- move of the PIT (basic timer) from mach-at91 to its proper location:
drivers/clocksource
- big cleanup of this driver along the way
* tag 'at91-drivers2' of git://github.com/at91linux/linux-at91:
ARM: at91: PIT: Move the driver to drivers/clocksource
ARM: at91: Give the PIT irq as an argument of at91sam926x_pit_init
ARM: at91: Convert the boards to the init_time callback
ARM: at91: soc: Add init_time callback
ARM: at91: PIT: (Almost) remove the global variables
ARM: at91: PIT: use request_irq instead of setup_irq
ARM: at91: PIT: Use pr_fmt
ARM: at91: PIT: Use consistent exit path in probe
ARM: at91: dt: Remove init_time definitions
ARM: at91: PIT: Rework probe functions
ARM: at91: PIT: Use of_have_populated_dt instead of CONFIG_OF
ARM: at91: PIT: Use DIV_ROUND_CLOSEST to compute the cycles
ARM: at91: generic.h: Add include safe guards
ARM: at91: PIT: Follow the general coding rules
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull parisc fixes from Helge Deller:
"We avoid using -mfast-indirect-calls for 64bit kernel builds to
prevent building an unbootable kernel due to latest gcc changes.
In the pdc_stable/firmware-access driver we fix a few possible stack
overflows and we now call secure_computing_strict() instead of
secure_computing() which fixes upcoming SECCOMP patches in the
for-next trees"
* 'parisc-3.17-7' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Only use -mfast-indirect-calls option for 32-bit kernel builds
parisc: pdc_stable.c: Avoid potential stack overflows
parisc: pdc_stable.c: Cleaning up unnecessary use of memset in conjunction with strncpy
parisc: ptrace: use secure_computing_strict()
This reverts commit f23cf8bd5c ("efi/x86: efistub: Move shared
dependencies to <asm/efi.h>") as well as the x86 parts of commit
f4f75ad574 ("efi: efistub: Convert into static library").
The road leading to these two reverts is long and winding.
The above two commits were merged during the v3.17 merge window and
turned the common EFI boot stub code into a static library. This
necessitated making some symbols global in the x86 boot stub which
introduced new entries into the early boot GOT.
The problem was that we weren't fixing up the newly created GOT entries
before invoking the EFI boot stub, which sometimes resulted in hangs or
resets. This failure was reported by Maarten on his Macbook pro.
The proposed fix was commit 9cb0e39423 ("x86/efi: Fixup GOT in all
boot code paths"). However, that caused issues for Linus when booting
his Sony Vaio Pro 11. It was subsequently reverted in commit
f3670394c2.
So that leaves us back with Maarten's Macbook pro not booting.
At this stage in the release cycle the least risky option is to revert
the x86 EFI boot stub to the pre-merge window code structure where we
explicitly #include efi-stub-helper.c instead of linking with the static
library. The arm64 code remains unaffected.
We can take another swing at the x86 parts for v3.18.
Conflicts:
arch/x86/include/asm/efi.h
Tested-by: Josh Boyer <jwboyer@fedoraproject.org>
Tested-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org> [arm64]
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>,
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
In spite of what the GCC manual says, the -mfast-indirect-calls has
never been supported in the 64-bit parisc compiler. Indirect calls have
always been done using function descriptors irrespective of the
-mfast-indirect-calls option.
Recently, it was noticed that a function descriptor was always requested
when the -mfast-indirect-calls option was specified. This caused
problems when the option was used in application code and doesn't make
any sense because the whole point of the option is to avoid using a
function descriptor for indirect calls.
Fixing this broke 64-bit kernel builds.
I will fix GCC but for now we need the attached change. This results in
the same kernel code as before.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v3.0+
Signed-off-by: Helge Deller <deller@gmx.de>
Prompted by a change to drivers/scsi/Kconfig which used to do a
"select NET" but now does a "depends on NET". This meant that some
configurations ended up without CONFIG_NET=y
Signed-off-by Tony Luck <tony.luck@intel.com>
Will Deacon pointed out, that the currently used opcode for filling holes,
that is 0xe7ffffff, seems not robust enough ...
$ echo 0xffffffe7 | xxd -r > test.bin
$ arm-linux-gnueabihf-objdump -m arm -D -b binary test.bin
...
0: e7ffffff udf #65535 ; 0xffff
... while for Thumb, it ends up as ...
0: ffff e7ff vqshl.u64 q15, <illegal reg q15.5>, #63
... which is a bit fragile. The ARM specification defines some *permanently*
guaranteed undefined instruction (UDF) space, for example for ARM in ARMv7-AR,
section A5.4 and for Thumb in ARMv7-M, section A5.2.6.
Similarly, ptrace, kprobes, kgdb, bug and uprobes make use of such instruction
as well to trap. Given mentioned section from the specification, we can find
such a universe as (where 'x' denotes 'don't care'):
ARM: xxxx 0111 1111 xxxx xxxx xxxx 1111 xxxx
Thumb: 1101 1110 xxxx xxxx
We therefore should use a more robust opcode that fits both. Russell King
suggested that we can even reuse a single 32-bit word, that is, 0xe7fddef1
which will fault if executed in ARM *or* Thumb mode as done in f928d4f2a8
("ARM: poison the vectors page"). That will still hold our requirements:
$ echo 0xf1defde7 | xxd -r > test.bin
$ arm-unknown-linux-gnueabi-objdump -m arm -D -b binary test.bin
...
0: e7fddef1 udf #56801 ; 0xdde1
$ echo 0xf1defde7f1defde7f1defde7 | xxd -r > test.bin
$ arm-unknown-linux-gnueabi-objdump -marm -Mforce-thumb -D -b binary test.bin
...
0: def1 udf #241 ; 0xf1
2: e7fd b.n 0x0
4: def1 udf #241 ; 0xf1
6: e7fd b.n 0x4
8: def1 udf #241 ; 0xf1
a: e7fd b.n 0x8
So on ARM 0xe7fddef1 conforms to the above UDF pattern, and the low 16 bit
likewise correspond to UDF in Thumb case. The 0xe7fd part is an unconditional
branch back to the UDF instruction.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When returning from a debug exception taken from EL1, we unmask debug
exceptions after handling the exception. This is crucial for debug
exceptions taken from EL0, so that any kernel work on the ret_to_user
path can be debugged by kgdb.
However, when returning back to EL1 the only thing left to do is to
restore the original register state before the exception return. If
single-step has been enabled by the debug exception handler, we will
get stuck in an infinite debug exception loop, since we will take the
step exception as soon as we unmask debug exceptions.
This patch avoids unmasking debug exceptions on the debug exception
return path when the exception was taken from EL1.
Fixes: 2a2830703a (arm64: debug: avoid accessing mdscr_el1 on fault paths where possible)
Cc: <stable@vger.kernel.org> #3.16+
Reported-by: David Long <dave.long@linaro.org>
Reported-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The _PAGE_IO_MAP PTE flag was only used by Xen PV guests to mark PTEs
that were used to map I/O regions that are 1:1 in the p2m. This
allowed Xen to obtain the correct PFN when converting the MFNs read
from a PTE back to their PFN.
Xen guests no longer use _PAGE_IOMAP for this. Instead mfn_to_pfn()
returns the correct PFN by using a combination of the m2p and p2m to
determine if an MFN corresponds to a 1:1 mapping in the the p2m.
Remove _PAGE_IOMAP, replacing it with _PAGE_UNUSED2 to allow for
future uses of the PTE flag.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Since mfn_to_pfn() returns the correct PFN for identity mappings (as
used for MMIO regions), the use of _PAGE_IOMAP is not required in
pte_mfn_to_pfn().
Do not set the _PAGE_IOMAP flag in pte_pfn_to_mfn() and do not use it
in pte_mfn_to_pfn().
This will allow _PAGE_IOMAP to be removed, making it available for
future use.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If a fault on a kernel address is due to a non-present page, then it
cannot be the result of stale TLB entry from a protection change (RO
to RW or NX to X). Thus the pagetable walk in spurious_fault() can be
skipped.
See the initial if in spurious_fault() and the tests in
spurious_fault_check()) for the set of possible error codes checked
for spurious faults. These are:
IRUWP
Before x00xx && ( 1xxxx || xxx1x )
After ( 10001 || 00011 ) && ( 1xxxx || xxx1x )
Thus the new condition is a subset of the previous one, excluding only
non-present faults (I == 1 and W == 1 are mutually exclusive).
This avoids spurious_fault() oopsing in some cases if the pagetables
it attempts to walk are not accessible. This obscures the location of
the original fault.
This also fixes a crash with Xen PV guests when they access entries in
the M2P corresponding to device MMIO regions. The M2P is mapped
(read-only) by Xen into the kernel address space of the guest and this
mapping may contains holes for non-RAM regions. Read faults will
result in calls to spurious_fault(), but because the page tables for
the M2P mappings are not accessible by the guest the pagetable walk
would fault.
This was not normally a problem as MMIO mappings would not normally
result in a M2P lookup because of the use of the _PAGE_IOMAP bit the
PTE. However, removing the _PAGE_IOMAP bit requires M2P lookups for
MMIO mappings as well.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
I discovered that some needed stuff is defined/declared in headers
which are not included directly. Currently it works but if somebody
remove required headers from currently included headers then build
will break. So, just in case directly include all needed headers.
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Instead of ballooning up and down dom0 memory this remaps the existing mfns
that were replaced by the identity map. The reason for this is that the
existing implementation ballooned memory up and and down which caused dom0
to have discontiguous pages. In some cases this resulted in the use of bounce
buffers which reduced network I/O performance significantly. This change will
honor the existing order of the pages with the exception of some boundary
conditions.
To do this we need to update both the Linux p2m table and the Xen m2p table.
Particular care must be taken when updating the p2m table since it's important
to limit table memory consumption and reuse the existing leaf pages which get
freed when an entire leaf page is set to the identity map. To implement this,
mapping updates are grouped into blocks with table entries getting cached
temporarily and then released.
On my test system before:
Total pages: 2105014
Total contiguous: 1640635
After:
Total pages: 2105014
Total contiguous: 2098904
Signed-off-by: Matthew Rushton <mrushton@amazon.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
This reverts commit 9cb0e39423.
It causes my Sony Vaio Pro 11 to immediately reboot at startup.
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
too some time to narrow down. Although a bit intrusive, this would
be good to get into the -rc cycle as there are quite a few boards
out there with omap3 es2.1 and es3.0, and we have those in at least
three boot test systems too that show errors without this patch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3MaO
-----END PGP SIGNATURE-----
Merge tag 'fix-v3.17-io-chain-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Regression fix for early omap3 revisions for wake-up events that
too some time to narrow down. Although a bit intrusive, this would
be good to get into the -rc cycle as there are quite a few boards
out there with omap3 es2.1 and es3.0, and we have those in at least
three boot test systems too that show errors without this patch.
* tag 'fix-v3.17-io-chain-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: Fix I/O chain clock line assertion timed out error
Signed-off-by: Olof Johansson <olof@lixom.net>
Gavin Shan