If of_find_i2c_device_by_node() or of_find_i2c_adapter_by_node() find
a device by node, but its type does not match, a reference to that
device is still held. This change fixes the problem.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using set_scl may be ineffective before calling the driver specific
prepare_recovery callback, which might change into a test mode. So
instead of setting SCL in i2c_generic_scl_recovery, move it to
i2c_generic_recovery (after the optional prepare_recovery).
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Mark (and unmark) device nodes with the POPULATE flag as appropriate.
This is required to avoid multi probing when using I2C and device
overlays containing a mux.
This patch is also more careful with the release of the adapter device
which caused a deadlock with muxes, and does not break the build
on !OF since the node flag accessors are not defined then.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Highlights:
- new drivers for Mediatek I2C, APM X-Gene, Broadcom Settop
- major updates to at91, davinci
- bugfixes to the mux infrastructure when dealing with the new quirk
mechanism
- more users for the bus recovery feature
- further improvements to the slave framework
Plus the usual bunch of smaller driver and core improvements and
fixes.
There is one patch removing old code from an ARM platform. This has
been acked by the sh_mobile maintainer Simon Horman"
* 'i2c/for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (48 commits)
i2c: busses: i2c-bcm2835: limits cdiv to allowed values
i2c: sh_mobile: use proper type for timeout
i2c: sh_mobile: use adapter default for timeout
i2c: rcar: use proper type for timeout
i2c: rcar: use adapter default for timeout
i2c: designware: Make sure the device is suspended before disabling runtime PM
i2c: tegra: apply size limit quirk
i2c: tegra: don't advertise SMBUS_QUICK
i2c: octeon: remove unused signal handling
i2c: davinci: Optimize SCL generation
i2c: mux: pca954x: Use __i2c_transfer because of quirks
i2c: mux: Use __i2c_transfer() instead of calling parent's master_xfer()
i2c: use parent adapter quirks in mux
i2c: bcm2835: clear reserved bits in S-Register
ARM: shmobile: r8a7740: remove I2C errata handling
i2c: sh_mobile: add errata workaround
i2c: at91: fix code checker warnings
i2c: busses: xgene-slimpro: fix incorrect __init declation for probe
i2c: davinci: Avoid sending to own address
i2c: davinci: Refactor i2c_davinci_wait_bus_not_busy()
...
sizeof(struct i2c_client) is 1088 bytes on a CONFIG_X86_64=y build and
produces following warning when CONFIG_FRAME_WARN is set to 1024:
drivers/i2c/i2c-core.c: In function ‘acpi_i2c_space_handler’:
drivers/i2c/i2c-core.c:367:1: warning: the frame size of 1152 bytes is
larger than 1024 bytes [-Wframe-larger-than=]
This is not critical given that kernel stack is 16 kB on x86_64 but lets
reduce the stack usage by allocating the struct i2c_client from the heap.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
int is vague, let's simply use the type of the variable in question.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Inform users what went wrong from the core, so drivers don't have to do
it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Following what DT already does. If the device does not have ACPI Interrupt
resource but instead it has one or more GpioInt resources listed below it,
we take the first GpioInt resource, convert it to suitable Linux IRQ number
and pass it to the driver instead.
This makes drivers simpler because the don't need to care about GPIOs at
all if only thing they need is interrupt.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is the convention used in most parts of the kernel including DT
counterpart of I2C slave enumeration. To make things consistent do the same
for ACPI I2C slave enumeration path as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 523c5b8964 ("i2c: Remove support for legacy PM") removed the PM
ops from the bus type, which causes the pm operations on the s3c2410
adapter device to fail (-ENOSUPP in rpm_callback). The adapter device
doesn't get bound to a driver and as such can't have its own pm_runtime
callbacks. Previously this was fine as the bus callbacks would have been
used, but now this can cause devices which use PM runtime and are
attached over I2C to fail to resume.
This commit fixes this issue by marking all adapter devices with
pm_runtime_no_callbacks, since they can't have any.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Beata Michalska <b.michalska@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 523c5b8964
Cc: stable@kernel.org
Current -next fails to link an ARM allmodconfig because drivers that use
the core recovery functions can be built as modules but those functions
are not exported:
ERROR: "i2c_generic_gpio_recovery" [drivers/i2c/busses/i2c-davinci.ko] undefined!
ERROR: "i2c_generic_scl_recovery" [drivers/i2c/busses/i2c-davinci.ko] undefined!
ERROR: "i2c_recover_bus" [drivers/i2c/busses/i2c-davinci.ko] undefined!
Add exports to fix this.
Fixes: 5f9296ba21 (i2c: Add bus recovery infrastructure)
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Generic PM domains support update including new PM domain
callbacks to handle device initialization better (Russell King,
Rafael J Wysocki, Kevin Hilman).
- Unified device properties API update including a new mechanism
for accessing data provided by platform initialization code
(Rafael J Wysocki, Adrian Hunter).
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano).
- intel_idle update including support for the Silvermont Core in
the Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause).
- New cpufreq driver for Hisilicon ACPU (Leo Yan).
- intel_pstate update including support for the Knights Landing
chip (Dasaratharaman Chandramouli, Kristen Carlson Accardi).
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann).
- powernv cpufreq driver update (Shilpasri G Bhat).
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi).
- powercap RAPL (Running-Average Power Limit) driver update
including support for Intel Broadwell server chips (Jacob Pan,
Mathias Krause).
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki).
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng).
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems
and a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede).
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu).
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki).
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu).
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu).
- Configurable delay for the system suspend/resume testing facility
(Brian Norris).
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=erd3
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups all over, although there are a few
items that sort of fall into the new feature category.
First off, we have new callbacks for PM domains that should help us to
handle some issues related to device initialization in a better way.
There also is some consolidation in the unified device properties API
area allowing us to use that inferface for accessing data coming from
platform initialization code in addition to firmware-provided data.
We have some new device/CPU IDs in a few drivers, support for new
chips and a new cpufreq driver too.
Specifics:
- Generic PM domains support update including new PM domain callbacks
to handle device initialization better (Russell King, Rafael J
Wysocki, Kevin Hilman)
- Unified device properties API update including a new mechanism for
accessing data provided by platform initialization code (Rafael J
Wysocki, Adrian Hunter)
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano)
- intel_idle update including support for the Silvermont Core in the
Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause)
- New cpufreq driver for Hisilicon ACPU (Leo Yan)
- intel_pstate update including support for the Knights Landing chip
(Dasaratharaman Chandramouli, Kristen Carlson Accardi)
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann)
- powernv cpufreq driver update (Shilpasri G Bhat)
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi)
- powercap RAPL (Running-Average Power Limit) driver update including
support for Intel Broadwell server chips (Jacob Pan, Mathias Krause)
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki)
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng)
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems and
a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede)
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu)
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki)
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu)
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu)
- Configurable delay for the system suspend/resume testing facility
(Brian Norris)
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
ACPI / scan: Fix NULL pointer dereference in acpi_companion_match()
ACPI / scan: Rework modalias creation when "compatible" is present
intel_idle: mark cpu id array as __initconst
powercap / RAPL: mark rapl_ids array as __initconst
powercap / RAPL: add ID for Broadwell server
intel_pstate: Knights Landing support
intel_pstate: remove MSR test
cpufreq: fix qoriq uniprocessor build
ACPI / scan: Take the PRP0001 position in the list of IDs into account
ACPI / scan: Simplify acpi_match_device()
ACPI / scan: Generalize of_compatible matching
device property: Introduce firmware node type for platform data
device property: Make it possible to use secondary firmware nodes
PM / watchdog: iTCO: stop watchdog during system suspend
cpufreq: hisilicon: add acpu driver
ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler
cpufreq: powernv: Report cpu frequency throttling
intel_idle: Add support for the Airmont Core in the Cherrytrail and Braswell SOCs
intel_idle: Update support for Silvermont Core in Baytrail SOC
PM / devfreq: tegra: Register governor on module init
...
Pull i2c updates from Wolfram Sang:
"Most notable:
- introducing the i2c_quirk infrastructure. Now, flaws of I2C
controllers can be described and the core will check if the flaws
collide with the messages to be sent
- wait_for_completion return type cleanup series
- new drivers for Digicolor, Netlogic XLP, Ingenic JZ4780
- updates to the I2C slave framework which include API changes. Its
only user was updated, too. Documentation was finally added
- changed dynamic bus numbering for the DT case. This could change
bus numbers for users. However, it fixes a collision where dynamic
and static busses request the same id.
- driver bugfixes, cleanups"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (52 commits)
i2c: xlp9xx: Driver for Netlogic XLP9XX/5XX I2C controller
of: Add vendor prefix 'netlogic'
i2c: davinci: use ICPFUNC to toggle I2C as gpio for bus recovery
i2c: davinci: use bus recovery infrastructure
i2c: change input parameter to i2c_adapter for prepare/unprepare_recovery
i2c: i2c-mux-gpio: remove error messages for probe deferrals
i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780
i2c: dln2: set the device tree node of the adapter
i2c: davinci: fixup wait_for_completion_timeout handling
i2c: mpc: Fix ISR return value
i2c: slave-eeprom: add more info when to increase the pointer
i2c: slave: add documentation for i2c-slave-eeprom
Documentation: i2c: describe the new slave mode
i2c: slave: rework the slave API
i2c: add support for the Digicolor I2C controller
i2c: busses with dynamic ids should start after fixed ids for DT
of: base: add function to get highest id of an alias stem
i2c: designware: Suppress error message if platform_get_irq() < 0
i2c: mpc: assign the correct prescaler from SVR
i2c: img-scb: fixup of wait_for_completion_timeout return handling
...
This patch changes type of input parameter for
prepare/unprepare_recovery() callbacks from struct i2c_bus_recovery_info
* to struct i2c_adapter *. This allows to simplify implementation of
these callbacks and avoid type conversations from i2c_bus_recovery_info
to i2c_adapter. The i2c_bus_recovery_info can be simply retrieved from
struct i2c_adapter which contains pointer on it. There are no users
currently, so this is safe to do.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure dynamic ids do not interfere with fixed ones and let them
start after the highest fixed id. This patch might cause different
bus-numbers than before for dynamic ids, however it fixes a bug. Assume:
- fixed id0 defers probe
- fixed id1 succeeds and registers a muxed bus with dynamic id
- muxed bus gets id0
- fixed id0 wants to probe again, but its fixed id is gone now
- fixed id0 probe fails
With this patch, the fixed ids are always reserved in the DT case.
For legacy board init, we already have a mechanism like this in
i2c_register_board_info().
Reported-by: Bob Feretich <bob.feretich@rafresearch.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now that we have struct fwnode_handle, we can use that to point to
ACPI companions from struct device objects instead of pointing to
struct acpi_device directly.
There are two benefits from that. First, the somewhat ugly and
hackish struct acpi_dev_node can be dropped and, second, the same
struct fwnode_handle pointer can be used in the future to point
to other (non-ACPI) firmware device node types.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Let the core do the checks if HW quirks prevent a transfer. Saves code
from drivers and adds consistency.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Ray Jui <rjui@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Tested-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Tested-By: Ludovic Desroches <ludovic.desroches@atmel.com>
This reverts commit e4df3a0b62
("i2c: core: Dispose OF IRQ mapping at client removal time")
Calling irq_dispose_mapping() will destroy the mapping and disassociate
the IRQ from the IRQ chip to which it belongs. Keeping it is OK, because
existent mappings are reused properly.
Also, this commit breaks drivers using devm* for IRQ management on
OF-based systems because devm* cleanup happens in device code, after
bus's remove() method returns.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Reported-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[wsa: updated the commit message with findings fromt the other bug report]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Fixes: e4df3a0b62
Pull i2c updates from Wolfram Sang:
"Summary:
- legacy PM code removed from the core, there were no users anymore
(thanks to Lars-Peter Clausen)
- new driver for Broadcom iProc
- bigger driver updates for designware, rk3x, cadence, ocores
- a bunch of smaller updates and bugfixes"
* 'i2c/for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (31 commits)
i2c: ocores: rework clk code to handle NULL cookie
i2c: designware-baytrail: another fixup for proper Kconfig dependencies
i2c: fix reference to functionality constants definition
i2c: iproc: Add Broadcom iProc I2C Driver
i2c: designware-pci: update Intel copyright line
i2c: ocores: add common clock support
i2c: hix5hd2: add COMPILE_TEST
i2c: clarify comments about the dev_released completion
i2c: ocores: fix clock-frequency binding usage
i2c: tegra: Maintain CPU endianness
i2c: designware-baytrail: use proper Kconfig dependencies
i2c: designware: Do not calculate SCL timing parameters needlessly
i2c: do not try to load modules for of-registered devices
i2c: designware: Add Intel Baytrail PMIC I2C bus support
i2c: designware: Add i2c bus locking support
of: i2c: Add i2c-mux-idle-disconnect DT property to PCA954x mux driver
i2c: designware: use {readl|writel}_relaxed instead of readl/writel
i2c: designware-pci: no need to provide clk_khz
i2c: designware-pci: remove Moorestown support
i2c: imx: whitespace and checkpatch cleanup
...
There was quite some confusion why this completion is there and if it is
still necessary. Sadly, it is. However, let's improve the comments and
share what we rediscovered.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make the slave support depend on CONFIG_I2C_SLAVE. Otherwise it gets
included unconditionally, even when it is not needed.
I2C bus drivers which implement slave support must select
I2C_SLAVE.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Trying to register an I2C device asynchronously (via async_schedule() call)
results in an ugly warning from request_module() warning about potential
deadlock (because request_module tries to wait for async works to
complete). While we could try to switch to request_module_nowait(), other
buses, as well as I2C itself when not using device tree, do not try to load
modules, but rather rely on the standard infrastructure (udev) to execute
module loading, and we should be doing the same.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Declaring attribute groups can be done with macros these days, let's use
them for consistency and readability reasons. Also, put the ATTR macros
directly below the referenced functions while we are here.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI specification allows I2C devices with multiple addresses. The current
implementation goes over all addresses and assigns the last one to the
device. This is typically not the primary address of the device.
Instead of doing that we assign the first address to the device and then
let the driver handle rest of the addresses as it wishes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There haven't been any I2C driver that use the legacy suspend/resume
callbacks for a while now and new drivers are supposed to use PM ops. So
remove support for legacy suspend/resume for I2C drivers.
Since there aren't any special bus specific things to do during
suspend/resume and since the PM core will automatically fallback directly to
using the device's PM ops if no bus PM ops are specified there is no need to
have any I2C bus PM ops.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"For 3.19, the I2C subsystem has to offer special candy this time.
Right in time for Christmas :)
- I2C slave framework: finally, a generic mechanism for Linux being
an I2C slave (if the bus driver supports that). Docs are still
missing but will come later this cycle, the code is good enough to
go.
- I2C muxes represent their topology in sysfs much more detailed.
This will help users to navigate around much easier.
- irq population of i2c clients is now done at probe time, not device
creation time, to have better support for deferred probing.
- new drivers for Imagination SCB, Amlogic Meson
- DMA support added for Freescale IMX, Renesas SHMobile
- slightly bigger driver updates to OMAP, i801, AT91, and rk3x
(mostly quirk handling, timing updates, and using better kernel
interfaces)
- eeprom driver can now write with byte-access (very slow, but OK to
have)
- and the bunch of smaller fixes, cleanups, ID updates..."
* 'i2c/for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (56 commits)
i2c: sh_mobile: remove unneeded DMA mask
i2c: rcar: add slave support
i2c: slave-eeprom: add eeprom simulator driver
i2c: core changes for slave support
MAINTAINERS: add I2C dt bindings also to I2C realm
i2c: designware: Fix falling time bindings doc
i2c: davinci: switch to use platform_get_irq
Documentation: i2c: Use PM ops instead of legacy suspend/resume
i2c: sh_mobile: optimize irq entry
i2c: pxa: add support for SCCB devices
omap: i2c: don't check bus state IP rev3.3 and earlier
i2c: s3c2410: Handle i2c sys_cfg register in i2c driver
i2c: rk3x: add Kconfig dependency on COMMON_CLK
i2c: omap: add notes related to i2c multimaster mode
i2c: omap: don't reset controller if Arbitration Lost detected
i2c: omap: implement workaround for handling invalid BB-bit values
i2c: omap: cleanup register definitions
i2c: rk3x: handle dynamic clock rate changes correctly
i2c: at91: enable probe deferring on dma channel request
i2c: at91: remove legacy DMA support
...
Finally(!), make Linux support being an I2C slave. Most of the existing
infrastructure is reused. We mainly add i2c_slave_register/unregister()
calls which tells i2c bus drivers to activate the slave mode. Then, they
also get a callback to report slave events to.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Lots of activity in the devicetree code for v3.18. Most of it is related
to getting all of the overlay support code in place, but there are other
important things in there.
There are a few trivial merge conflicts. They shouldn't give you any
trouble.
Highlights:
- OF_RECONFIG notifiers for SPI, I2C and Platform devices. Those
subsystems can now respond to live changes to the device tree.
- CONFIG_OF_OVERLAY method for applying live changes to the device tree
- Removal of the of_allnodes list. This used to be used to iterate over
all the nodes in the device tree, but it is unnecessary because the
same thing can be done by iterating over the list of child pointers.
Getting rid of of_allnodes saves some memory and avoids the
possibility of of_allnodes being sorted differently from the child
lists.
- Support for retrieving original DTB blob via sysfs. Needed by kexec.
- More unittests
- Documentation and minor bug fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ak0A
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree changes from Grant Likely:
"Lots of activity in the devicetree code for v3.18. Most of it is
related to getting all of the overlay support code in place, but there
are other important things in there.
Highlights:
- OF_RECONFIG notifiers for SPI, I2C and Platform devices. Those
subsystems can now respond to live changes to the device tree.
- CONFIG_OF_OVERLAY method for applying live changes to the device
tree
- Removal of the of_allnodes list. This used to be used to iterate
over all the nodes in the device tree, but it is unnecessary
because the same thing can be done by iterating over the list of
child pointers. Getting rid of of_allnodes saves some memory and
avoids the possibility of of_allnodes being sorted differently from
the child lists.
- Support for retrieving original DTB blob via sysfs. Needed by
kexec.
- More unittests
- Documentation and minor bug fixes"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux: (42 commits)
of: Delete unnecessary check before calling "of_node_put()"
of: Drop ->next pointer from struct device_node
spi: Check for spi_of_notifier when CONFIG_OF_DYNAMIC=y
of: support passing console options with stdout-path
of: add optional options parameter to of_find_node_by_path()
of: Add bindings for chosen node, stdout-path
of: Remove unneeded and incorrect MODULE_DEVICE_TABLE
ARM: dt: fix up PL011 device tree bindings
of: base, fix of_property_read_string_helper kernel-doc
of: remove select of non-existant OF_DEVICE config symbol
spi/of: Add OF notifier handler
spi/of: Create new device registration method and accessors
i2c/of: Add OF_RECONFIG notifier handler
i2c/of: Factor out Devicetree registration code
of/overlay: Add overlay unittests
of/overlay: Introduce DT overlay support
of/reconfig: Add OF_DYNAMIC notifier for platform_bus_type
of/reconfig: Always use the same structure for notifiers
of/reconfig: Add debug output for OF_RECONFIG notifiers
of/reconfig: Add empty stubs for the of_reconfig methods
...
CONFIG_OF_DYNAMIC enables runtime changes to the device tree which in
turn may trigger addition or removal of devices from Linux. Add an
OF_RECONFIG notifier handler to receive tree change events and to
creating or destroy i2c devices as required.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[grant.likely: clean up #ifdefs and drop unneeded error handling]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-i2c@vger.kernel.org
Dynamically inserting i2c client device nodes requires the use
of a single device registration method. Factor out the loop body of
of_i2c_register_devices() so that it can be called for individual
device_nodes instead of for all the children of a node.
Note: The diff of this commit looks far more complicated than it
actually is due the indentation being changed for a large block of code.
When viewed using the diff -w flag to ignore whitespace changes it can
be seen that the change is actually quite simple.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[grant.likely: Made new function static and removed changes to header]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-i2c@vger.kernel.org
ACPI 5.0 introduces _DEP (Operation Region Dependencies) to designate
device objects that OSPM should assign a higher priority in start
ordering due to future operation region accesses.
On Asus T100TA, ACPI battery info are read from a I2C slave device via
I2C operation region. Before I2C operation region handler is installed,
battery _STA always returns 0. There is a _DEP method of designating
start order under battery device node.
This patch is to implement _DEP feature to fix battery issue on the
Asus T100TA. Introducing acpi_dep_list and adding dep_unmet count
in struct acpi_device. During ACPI namespace scan, create struct
acpi_dep_data for a valid pair of master (device pointed to by _DEP)/
slave(device with _DEP), record master's and slave's ACPI handle in
it and put it into acpi_dep_list. The dep_unmet count will increase
by one if there is a device under its _DEP. Driver's probe() should
return EPROBE_DEFER when find dep_unmet is larger than 0. When I2C
operation region handler is installed, remove all struct acpi_dep_data
on the acpi_dep_list whose master is pointed to I2C host controller
and decrease slave's dep_unmet. When dep_unmet decreases to 0, all
_DEP conditions are met and then do acpi_bus_attach() for the device
in order to resolve battery _STA issue on the Asus T100TA.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=69011
Tested-by: Jan-Michael Brummer <jan.brummer@tabos.org>
Tested-by: Adam Williamson <adamw@happyassassin.net>
Tested-by: Michael Shigorin <shigorin@gmail.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No need to initialize 'ret' if it gets assigned directly after that.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since commit 2fd36c5526 ("i2c: core: Map OF IRQ at probe time"),
i2c slaves without interrupts (e.g. da9210 and at24 on r8a7791/koelsch)
fail to probe:
at24: probe of 2-0050 failed with error -22
da9210: probe of 6-0068 failed with error -22
This happens because the call to of_irq_get() in i2c_device_probe()
returns -EINVAL.
If a device node does not have an "interrupts" property,
of_irq_parse_one() fails. Unlike irq_of_parse_and_map(), of_irq_get()
does not ignore errors from of_irq_parse_one(), but forwards them.
Make i2c_device_probe() ignore all errors but -EPROBE_DEFER to fix this,
just like platform_get_irq() and platform_get_irq_byname() already do.
Fixes: 2fd36c5526 ("i2c: core: Map OF IRQ at probe time")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C clients instantiated from OF get their IRQ mapped at device
registration time. This leads to the IRQ being silently ignored if the
related irqchip hasn't been proved yet.
Fix this by moving IRQ mapping at probe time using of_get_irq(). The
function operates as irq_of_parse_and_map() but additionally returns
-EPROBE_DEFER if the irqchip isn't available, allowing us to defer I2C
client probing.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Clients instantiated from OF get an IRQ mapping created at device
registration time. Dispose the mapping when the client is removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The commit 46420dd73b (PM / Domains: Add APIs to attach/detach a PM
domain for a device) started using errno values in pm.h header file.
It also failed to include the header for these, thus it caused
compiler errors.
Instead of including the errno header to pm.h, let's move the functions
to pm_domain.h, since it's a better match.
Fixes: 46420dd73b (PM / Domains: Add APIs to attach/detach a PM domain for a device)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If adapter->dev.parent == NULL there is a NULL pointer dereference in
acpi_i2c_install_space_handler and acpi_i2c_remove_space_handler.
This is present since introduction of this code:
366047515c "i2c: rework kernel config I2C_ACPI" or even
da3c6647ee "I2C/ACPI: Clean up I2C ACPI code and Add CONFIG_I2C_ACPI"
The adapter->dev.parent == NULL case is valid for the i2c_stub,
so loading i2c_stub with ACPI_I2C_OPREGION enabled results in an oops.
This is also valid at least for i2c_tiny_usb and i2c_robotfuzz_osif.
Fix by checking whether it is null before calling ACPI_HANDLE.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 5d98e61d33 ("I2C/ACPI: Add i2c ACPI operation region support")
renamed the i2c-core module. This may cause regressions for
distributions, so put the ACPI code back into the core.
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Lan Tianyu <tianyu.lan@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Previously only the ACPI PM domain was supported by the i2c bus.
Let's convert to the common attach/detach functions for PM domains,
which currently means we are extending the support to include the
generic PM domain as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull i2c updates from Wolfram Sang:
"Highlights:
- class based instantiation finally dropped for most embedded drivers
bringing boot up performance gains
- removed two drivers (one outdated, one a duplicate)
- ACPI has now operation region support (thanks to Lan Tianyu)
- the i2c-stub driver got overhauled and gained new features to
become more useful when writing i2c client drivers (thanks to
Guenter Roeck and Jean Delvare)
The rest is driver bugfixes, added bindings/ids, cleanups..."
* 'i2c/for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (43 commits)
i2c: mpc: delete unneeded test before of_node_put
i2c: rk3x: fix interrupt handling issue
i2c: imx: Fix format warning for dev_dbg
i2c: qup: disable clks and return instead of just returning error
i2c: exynos5: always enable HSI2C
i2c: designware: add new bindings
i2c: gpio: Drop dead code in i2c_gpio_remove
i2c: pca954x: put the mux to disconnected state after resume
i2c: st: Update i2c timings
drivers/i2c/busses: use correct type for dma_map/unmap
i2c: i2c-st: Use %pa to print 'resource_size_t' type
i2c: s3c2410: resume the I2C controller earlier
i2c: stub: Avoid an array overrun on I2C block transfers
i2c: i801: Add device ID for Intel Wildcat Point PCH
i2c: i801: Fix the alignment of the device table
i2c: stub: Add support for banked register ranges
i2c: stub: Remember the number of emulated chips
i2c: stub: Add support for SMBus block commands
i2c: efm32: correct namespacing of location property
i2c: exynos5: remove extra line and fix an assignment
...
This patch adds helper functions to configure clock parents and rates
as specified through 'assigned-clock-parents', 'assigned-clock-rates'
DT properties for a clock provider or clock consumer device.
The helpers are now being called by the bus code for the platform, I2C
and SPI busses, before the driver probing and also in the clock core
after registration of a clock provider.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
We have a warning already when support for old-fashioned class based
instantiation is about to be dropped somewhen soon from a driver. Let's
have another one when it was actually dropped. This allows to remove the
cruft a little earlier and still let users know what happened in the
rare case they are missing devices after the change. However, there is
enough interest to get rid of class based instantiation rather sooner
than later because it improves boot up time.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Clean up ACPI related code in the i2c core and add CONFIG_I2C_ACPI
to enable I2C ACPI code.
Current there is a race between removing I2C ACPI operation region
and ACPI AML code accessing. So make i2c core built-in if CONFIG_I2C_ACPI
is set.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI 5.0 spec(5.5.2.4.5) defines GenericSerialBus(i2c, spi, uart) operation region.
It allows ACPI aml code able to access such kind of devices to implement
some ACPI standard method.
ACPI Spec defines some access attribute to associate with i2c protocol.
AttribQuick Read/Write Quick Protocol
AttribSendReceive Send/Receive Byte Protocol
AttribByte Read/Write Byte Protocol
AttribWord Read/Write Word Protocol
AttribBlock Read/Write Block Protocol
AttribBytes Read/Write N-Bytes Protocol
AttribProcessCall Process Call Protocol
AttribBlockProcessCall Write Block-Read Block Process Call Protocol
AttribRawBytes Raw Read/Write N-BytesProtocol
AttribRawProcessBytes Raw Process Call Protocol
On the Asus T100TA, Bios use GenericSerialBus operation region to access
i2c device to get battery info.
Sample code From Asus T100TA
Scope (_SB.I2C1)
{
Name (UMPC, ResourceTemplate ()
{
I2cSerialBus (0x0066, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.I2C1",
0x00, ResourceConsumer, ,
)
})
...
OperationRegion (DVUM, GenericSerialBus, Zero, 0x0100)
Field (DVUM, BufferAcc, NoLock, Preserve)
{
Connection (UMPC),
Offset (0x81),
AccessAs (BufferAcc, AttribBytes (0x3E)),
FGC0, 8
}
...
}
Device (BATC)
{
Name (_HID, EisaId ("PNP0C0A")) // _HID: Hardware ID
Name (_UID, One) // _UID: Unique ID
...
Method (_BST, 0, NotSerialized) // _BST: Battery Status
{
If (LEqual (AVBL, One))
{
Store (FGC0, BFFG)
If (LNotEqual (STAT, One))
{
ShiftRight (CHST, 0x04, Local0)
And (Local0, 0x03, Local0)
If (LOr (LEqual (Local0, One), LEqual (Local0, 0x02)))
{
Store (0x02, Local1)
}
...
}
The i2c operation region is defined under I2C1 scope. _BST method under
battery device BATC read battery status from the field "FCG0". The request
would be sent to i2c operation region handler.
This patch is to add i2c ACPI operation region support. Due to there are
only "Byte" and "Bytes" protocol access on the Asus T100TA, other protocols
have not been tested.
About RawBytes and RawProcessBytes protocol, they needs specific drivers to interpret
reference data from AML code according ACPI 5.0 SPEC(5.5.2.4.5.3.9 and 5.5.2.4.5.3.10).
So far, not found such case and will add when find real case.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SMBUS tracepoints can be enabled thusly:
echo 1 >/sys/kernel/debug/tracing/events/i2c/enable
and will dump messages that can be viewed in /sys/kernel/debug/tracing/trace
that look like:
... smbus_read: i2c-0 a=051 f=0000 c=fa BYTE_DATA
... smbus_reply: i2c-0 a=051 f=0000 c=fa BYTE_DATA l=1 [39]
... smbus_result: i2c-0 a=051 f=0000 c=fa BYTE_DATA rd res=0
formatted as:
i2c-<adapter-nr>
a=<addr>
f=<flags>
c=<command>
<protocol-name>
<rd|wr>
res=<result>
l=<data-len>
[<data-block>]
The adapters to be traced can be selected by something like:
echo adapter_nr==1 >/sys/kernel/debug/tracing/events/i2c/filter
Note that this shares the same filter and enablement as i2c.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add tracepoints into the I2C message transfer function to retrieve the message
sent or received. The following config options must be turned on to make use
of the facility:
CONFIG_FTRACE
CONFIG_ENABLE_DEFAULT_TRACERS
The I2C tracepoint can be enabled thusly:
echo 1 >/sys/kernel/debug/tracing/events/i2c/enable
and will dump messages that can be viewed in /sys/kernel/debug/tracing/trace
that look like:
... i2c_write: i2c-5 #0 a=044 f=0000 l=2 [02-14]
... i2c_read: i2c-5 #1 a=044 f=0001 l=4
... i2c_reply: i2c-5 #1 a=044 f=0001 l=4 [33-00-00-00]
... i2c_result: i2c-5 n=2 ret=2
formatted as:
i2c-<adapter-nr>
#<message-array-index>
a=<addr>
f=<flags>
l=<datalen>
n=<message-array-size>
ret=<result>
[<data>]
The operation is done between the i2c_write/i2c_read lines and the i2c_reply
and i2c_result lines so that if the hardware hangs, the trace buffer can be
consulted to determine the problematic operation.
The adapters to be traced can be selected by something like:
echo adapter_nr==1 >/sys/kernel/debug/tracing/events/i2c/filter
These changes are based on code from Steven Rostedt.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
[wsa: adapted path for 'enable' in the commit msg]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Class based instantiation can cause noticeable delays when booting. This
mechanism is used when it is not possible to describe slaves on I2C
busses. As we do have other mechanisms, most embedded I2C will not need
classes and for embedded it is explicitly not recommended to use them. Add
a deprecation warning for drivers which want to disable class based
instantiation in the near future to gain boot-up time, so users relying
on this technique can switch to something better. They really should.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Vladimir Zapolskiy