I got this working a couple of years ago. Remove it from the
list of known issues.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The original code was based on my reverse engineering of an I2C trace
of the Windows driver. Now that I know what the registers actually do,
restructure the code a bit, removing some unneeded register programming
and fixing the sequencing of operations.
This reduces the time it takes to change inputs from 1300ms down to
600ms (as measured by "time v4l2-ctl -i 0")
Note this does not address outstanding issues related to the management
of the module clocks and power control for the various blocks, which
will be done in a separate patch.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some stray lines got inserted into the driver when I reverse engineered
the I2C traffic (at the time I didn't know what the registers did).
It turns up these registers muck with the onboard I2C master, which
we don't use since we instead use the I2C gate. Remove the lines
which can actually interfere with the operation of the bus.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since we don't suppoort sliced VBI with the au0828/au8522, there is
no need to configure the au8522 VBI slicer, which because of the
coefficients requires a large amount of i2c traffic.
Remove the relevant code. Note that this has no effect on raw VBI
support, which is currently the only supported way to access VBI on
this device.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Minor fixes in comments
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hardware could support up to 16 logical addresses which is more
than needed by CEC specifications.
Let use CEC_MAX_LOG_ADDRS instead of limited it on one.
stih_cec_adap_log_addr() function was alredy written to support
multiple addresses requests.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the missing endianness conversions to a debug call printing the
USB device-descriptor idVendor and idProduct fields during probe.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The VIDIOC_G/S_EDID ioctls can return valid data even if an error is returned.
Mark those ioctls accordingly. Rather than using an explicit 'if' to check for the
ioctl (as was done until now for VIDIOC_QUERY_DV_TIMINGS) just set a new flag in the
v4l2_ioctls array.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In 'commit 295ab497d6 ("[media] media: platform: pxa_camera: make
printk consistent")' a pointer to the device structure in
mclk_get_divisor() was changed to pcdev_to_dev(pcdev). The pointer used
by pcdev_to_dev() is still uninitialized during the call to
mclk_get_divisor() as it happens in v4l2_device_register() at the end
of the probe. The dev_warn and dev_dbg caused a line in the log:
(NULL device *): Limiting master clock to 26000000
Fix this by using an initialized pointer from the platform_device
(as before the old patch).
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2-compliance complains about nonexistent vidioc_subscribe_event
and vidioc_unsubscribe_event calls. Add them to fix the complaints.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
During the transfer from the soc_camera a test in pxa_mbus_image_size()
got removed. Without it any PXA_MBUS_LAYOUT_PACKED format causes either
the return of a wrong value (PXA_MBUS_PACKING_2X8_PADHI doubles
the correct value) or EINVAL (PXA_MBUS_PACKING_NONE and
PXA_MBUS_PACKING_EXTEND16). This was observed in an error from the ffmpeg
(for some of the YUYV subvariants).
This patch re-adds the same test as in soc_camera version.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds Bayer 8 GBRG and RGGB support and move GRBG definition
close to BGGR (so all Bayer 8 variants are together). No other changes are
needed as the driver handles them as RAW data stream.
The RGGB variant was tested in a modified OV9640 driver.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Permits distinguishing between two /dev/videoX entries from the same
physical UVC device (that naturally share the same iProduct name).
This change matches current Windows behavior by prioritizing iFunction
over iInterface, but unlike Windows it displays both iProduct and
iFunction/iInterface strings when both are available.
Signed-off-by: Peter Boström <pbos@google.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the probe def quirk for the webcam found in the Apple MacBook Pro
2016, to get it working out of the box.
Signed-off-by: Daniel Roschka <danielroschka@phoenitydawn.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- avoid duplicate debugging messages in em28xx_read_reg_req_len()
- do not describe successful usb transfers in em28xx_read_reg_len()
as "failed"
- report errors in em28xx_write_regs_req(), too
- print the usb error numbers, too
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
trivial fix to spelling mistake and add in a white space in
a CX18_ERR error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In functions cx25840_initialize(), cx231xx_initialize(), and
cx23885_initialize(), the return value of create_singlethread_workqueue()
is used without validation. This may result in NULL dereference and cause
kernel crash. This patch fixes it.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Function pci_find_ext_capability() may return 0, which is an invalid
address. In function cobalt_pcie_status_show(), its return value is used
without validation. This patch adds checks to validate the return
address.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Function kthread_create() returns an ERR_PTR on error. However, in
function s5k83a_start(), its return value is used without validation.
This may result in a bad memory access bug. This patch fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The recent changes in 4.9 to mandate USB buffers be heap allocated
broke this driver, which was allocating the buffers on the stack.
This resulted in the device failing at initialization.
Introduce dedicated send/receive buffers as part of the state
structure, and add a mutex to protect access to them.
Note: we also had to tweak the API to mxl111sf_ctrl_msg to pass
the pointer to the state struct rather than the device, since
we need it inside the function to access the buffers and the
mutex. This patch adjusts the callers to match the API change.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Reported-by: Doug Lung <dlung0@gmail.com>
Cc: Michael Ira Krufky <mkrufky@linuxtv.org>
Cc: <stable@vger.kernel.org> # for v4.5 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sometimes 'DMA single access' is not enough to transfer
a frame of image, '8-beat burst access' is set as the
default DMA memory burst size.
Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Setting initial standard at the top of cx8800_initdev would cause the
first call to cx88_set_tvnorm() to return without programming any
registers (leaving the driver saying it's set to NTSC but the hardware
isn't programmed). Even worse, any subsequent attempt to explicitly
set it to NTSC-M will return success but actually fail to program the
underlying registers unless first changing the standard to something
other than NTSC-M.
Set the initial standard later in the process, and make sure the field
is zero at the beginning to ensure that the call always goes through.
This regression was introduced in the following commit:
commit ccd6f1d488 ("[media] cx88: move width, height and field to core
struct")
Author: Hans Verkuil <hans.verkuil@cisco.com>
[media] cx88: move width, height and field to core struct
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: <stable@vger.kernel.org> # for v3.19 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds documentation of device tree bindings for the STM32 DCMI
(Digital Camera Memory Interface).
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On this driver, it can fall through a switch. I tried to
annotate it, in order to shut up a gcc warning, but that
didn't work, as the logic there is somewhat complex.
So, instead, let's just repeat the code. gcc should likely
optimize it anyway, and this makes the code better readable,
IMHO.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Clearly, hsync and vsinc bool vars are part of the return
logic on the second case of the switch. Annotate that, in
order to shut up gcc warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are two cases here that it does a switch fall through.
Annotate it, in order to shut up gcc warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On two switches, this driver have unannotated switch
fall through.
in the first case, it falls through a return. On the second
one, it prints undesired log messages on fall through.
Solve that by copying the commands that it should be
running. Gcc will very likely optimize it anyway, so this
sholdn't be causing any harm, and shuts up gcc warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The atomisp currently produce hundreds of warnings when W=1.
It is a known fact that this driver is currently in bad
shape, and there are lot of things to be done here.
We don't want to be bothered by those "minor" stuff for now,
while the driver doesn't receive a major cleanup. So,
disable those warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Gcc 7.1 complains that:
drivers/media/platform/mtk-vcodec/mtk_vcodec_dec.c: In function 'mtk_vdec_pic_info_update':
drivers/media/platform/mtk-vcodec/mtk_vcodec_dec.c:284:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
int ret;
^~~
Indeed, if debug is disabled, "ret" is never used. The best
fix for it seems to make the fuction to return an error code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Gcc 7.1 complains about:
drivers/media/platform/s5p-jpeg/jpeg-core.c: In function 's5p_jpeg_parse_hdr.isra.9':
drivers/media/platform/s5p-jpeg/jpeg-core.c:1207:12: warning: 'width' may be used uninitialized in this function [-Wmaybe-uninitialized]
result->w = width;
~~~~~~~~~~^~~~~~~
drivers/media/platform/s5p-jpeg/jpeg-core.c:1208:12: warning: 'height' may be used uninitialized in this function [-Wmaybe-uninitialized]
result->h = height;
~~~~~~~~~~^~~~~~~~
Indeed the code would allow it to return a random value (although
it shouldn't happen, in practice). So, explicitly set both to zero,
just in case.
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Avoid warnings like those:
drivers/media/pci/ddbridge/ddbridge-core.c: In function 'dvb_input_detach':
drivers/media/pci/ddbridge/ddbridge-core.c:787:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (input->fe) {
^
drivers/media/pci/ddbridge/ddbridge-core.c:792:2: note: here
case 4:
^~~~
...
On several cases, it is just that gcc 7.1 is not capable of
understanding the comment, but on other places, we need an
annotation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When a REMOTE_KEY_PRESSED event happens, it does the right
thing. However, if debug is enabled, it will print a bogus
message warning that "key repeated".
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The logic that handles CA_SET_PID is clearly missing a
break: it prints that the command succeeded, but, due to the
missing break, it would be returning -EOPNOTSUPP, as if the
driver weren't supporting such ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Right now, the driver is doing the right thing for
PVC_ERRORCODE_UNKNOWN and PVC_ERRORCODE_INVALID_CONTROL:
for both, it returns an error code (SAA_ERR_NOT_SUPPORTED).
However, it is printing two error messages instead of one
on those cases.
Fix the logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There's a missing break for VSB16 modulation logic, with would
cause it to return -EINVAL, instead of handling it.
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
gcc-7 suggests that an expression using a bitwise not and a bitmask
on a 'bool' variable is better written using boolean logic:
drivers/media/rc/imon.c: In function 'imon_incoming_scancode':
drivers/media/rc/imon.c:1725:22: error: '~' on a boolean expression [-Werror=bool-operation]
ictx->pad_mouse = ~(ictx->pad_mouse) & 0x1;
^
drivers/media/rc/imon.c:1725:22: note: did you mean to use logical not?
I agree.
Fixes: 21677cfc56 ("V4L/DVB: ir-core: add imon driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is a patch to the atomisp_tpg.c file that fixes up a missing
blank line warning found by the checkpatch.pl tool
Signed-off-by: Manny Vindiola <mannyv@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We're putting the NUL terminators one space beyond where they belong.
This doesn't show up in testing because all but the callers put a NUL in
the correct place themselves. LOL. It causes a static checker warning
about buffer overflows.
Fixes: a49d25364d ("staging/atomisp: Add support for the Intel IPU v2")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We should verify that "ix < max_len" before we test whether we have
reached the NUL terminator.
Fixes: a49d25364d ("staging/atomisp: Add support for the Intel IPU v2")
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With gcc-7.1.1 I was getting the following compile error:
error: ‘*’ in boolean context, suggest ‘&&’ instead
The problem is the definition of CEIL_DIV:
#define CEIL_DIV(a, b) ((b) ? ((a) + (b) - 1) / (b) : 0)
Which when called as: CEIL_DIV(x, y * z) triggers this error, note
we cannot do as the error suggests since b is evaluated multiple times.
This commit fixes these compile errors.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix sparse warnings: "symbol not declared; should it be static?"
Signed-off-by: Guru Das Srinagesh <gurooodas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix for error (not warnings) reported by checkpatch.pl
Specifically:
- missing whitespace around "=" and after ","
- indentation with spaces instead of tabs
- lines starting with a whitespace
This patch does not affect the compiled code in any way.
Signed-off-by: Avraham Shukron <avraham.shukron@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixes a sparse warning:
drivers/staging/media/atomisp/platform/intel-mid/intel_mid_pcihelpers.c:35:5: warning: symbol 'qos' was not declared. Should it be static?
Signed-off-by: Valentin Vidic <Valentin.Vidic@CARNet.hr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Devin Heitmueller