o GET_LED_STATUS command will be used by driver to get
current beacon state from 82xx adapter.
o Refactored qlcnic_store_beacon() to split 8200 and 8300
specific calls.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide diagnostics routines enough time to unwind before
proceeding with reset recovery.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test and set diagnostics mode bit before starting
diagnostics tests. Stop diagnostics tests if adapter is resetting.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o work_struct should be initialized before cancel_delayed_work
call to destroy it.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic_config_npars module parameter is used to configure NPAR
operational modes where NPAR function is used for PCI passthrough.
Removing this paramter as PCI passthrough is not supported for
NPAR functions.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Updated IRQ name for 8200 and 8300 Series adapter as per
format used by other multiqueue drivers.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Set HW mask for 8300 Series adapter, in INT-x mode, to
stop generating interrupt during driver unload.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add support for spoof check configuration per VF using
iproute2 tool.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge net into net-next because some upcoming net-next changes
build on top of bug fixes that went into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
o After change in EPORT features of 82xx adapter, netdev->features needs to
be updated to reflect EPORT feature updates but driver was manipulating
netdev->features at wrong place.
o This patch uses netdev_update_features() and .ndo_fix_features() to
update netdev->features properly.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code is removed because netdev->trans_start updates made by the driver
will be ignored by the kernel.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix error paths in probe to assign proper error codes to probe return value.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlge allocates chunks from a page that it maps and unmaps that page when
the last chunk is released. When the driver is unloaded or the card is
removed, all chunks are released and the page is unmapped for the last
chunk.
However, when the last chunk of a page is not allocated and the device
is removed, that page is not unmapped. In fact, its last reference is
not put and there's also a page leak. This bug prevents a device from
being properly hotplugged.
When the DMA API debug option is enabled, the following messages show
the pending DMA allocation after we remove the driver.
This patch fixes the bug by unmapping and putting the page from the ring
if its last chunk has not been allocated.
pci 0005:98:00.0: DMA-API: device driver has pending DMA allocations while released from device [count=1]
One of leaked entries details: [device address=0x0000000060a80000] [size=65536 bytes] [mapped with DMA_FROM_DEVICE] [mapped as page]
------------[ cut here ]------------
WARNING: at lib/dma-debug.c:746
Modules linked in: qlge(-) rpadlpar_io rpaphp pci_hotplug fuse [last unloaded: qlge]
NIP: c0000000003fc3ec LR: c0000000003fc3e8 CTR: c00000000054de60
REGS: c0000003ee9c74e0 TRAP: 0700 Tainted: G O (3.7.2)
MSR: 8000000000029032 <SF,EE,ME,IR,DR,RI> CR: 28002424 XER: 00000001
SOFTE: 1
CFAR: c0000000007a39c8
TASK = c0000003ee8d5c90[8406] 'rmmod' THREAD: c0000003ee9c4000 CPU: 31
GPR00: c0000000003fc3e8 c0000003ee9c7760 c000000000c789f8 00000000000000ee
GPR04: 0000000000000000 00000000000000ef 0000000000004000 0000000000010000
GPR08: 00000000000000be c000000000b22088 c000000000c4c218 00000000007c0000
GPR12: 0000000028002422 c00000000ff26c80 0000000000000000 000001001b0f1b40
GPR16: 00000000100cb9d8 0000000010093088 c000000000cdf910 0000000000000001
GPR20: 0000000000000000 c000000000dbfc00 0000000000000000 c000000000dbfb80
GPR24: c0000003fafc9d80 0000000000000001 000000000001ff80 c0000003f38f7888
GPR28: c000000000ddfc00 0000000000000400 c000000000bd7790 c000000000ddfb80
NIP [c0000000003fc3ec] .dma_debug_device_change+0x22c/0x2b0
LR [c0000000003fc3e8] .dma_debug_device_change+0x228/0x2b0
Call Trace:
[c0000003ee9c7760] [c0000000003fc3e8] .dma_debug_device_change+0x228/0x2b0 (unreliable)
[c0000003ee9c7840] [c00000000079a098] .notifier_call_chain+0x78/0xf0
[c0000003ee9c78e0] [c0000000000acc20] .__blocking_notifier_call_chain+0x70/0xb0
[c0000003ee9c7990] [c0000000004a9580] .__device_release_driver+0x100/0x140
[c0000003ee9c7a20] [c0000000004a9708] .driver_detach+0x148/0x150
[c0000003ee9c7ac0] [c0000000004a8144] .bus_remove_driver+0xc4/0x150
[c0000003ee9c7b60] [c0000000004aa58c] .driver_unregister+0x8c/0xe0
[c0000003ee9c7bf0] [c0000000004090b4] .pci_unregister_driver+0x34/0xf0
[c0000003ee9c7ca0] [d000000002231194] .qlge_exit+0x1c/0x34 [qlge]
[c0000003ee9c7d20] [c0000000000e36d8] .SyS_delete_module+0x1e8/0x290
[c0000003ee9c7e30] [c0000000000098d4] syscall_exit+0x0/0x94
Instruction dump:
7f26cb78 e818003a e87e81a0 e8f80028 e9180030 796b1f24 78001f24 7d6a5a14
7d2a002a e94b0020 483a7595 60000000 <0fe00000> 2fb80000 40de0048 80120050
---[ end trace 4294f9abdb01031d ]---
Mapped at:
[<d000000002222f54>] .ql_update_lbq+0x384/0x580 [qlge]
[<d000000002227bd0>] .ql_clean_inbound_rx_ring+0x300/0xc60 [qlge]
[<d0000000022288cc>] .ql_napi_poll_msix+0x39c/0x5a0 [qlge]
[<c0000000006b3c50>] .net_rx_action+0x170/0x300
[<c000000000081840>] .__do_softirq+0x170/0x300
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Jitendra Kalsaria <Jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o VF driver that has enabled asynchronous link events
may not set BIT_8 in the request, if it does not require
link state in the response.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Fix mailbox response poll time to maximum 5 seconds which
includes mailbox response time as well as time required for
processing AEN if any.
o Driver need to read firmware control mailbox register instead
of host control mailbox register.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o In order to perform reset recovery during diagnostics tests,
current device status information need to be preserved.
This patch makes the required changes in diagnostics routines
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o When transmit timeout happens, recovery attempt should start with
adapter soft reset. If soft reset fails to resume traffic, firmware
dump will be collected and driver will perform a hard reset of the
adapter. Reset recovery on 83xx was failing after a hard reset.
This patch fixes that issue.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Fix display for interface while using 'ethtool <device>' for 83xx adapter
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add missing information in ethtool statistics information array.
o Fix the typo in the statistics information string.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Delete previous unicast MAC which is already programmed
in adapter before setting new unicast MAC
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Added identifying strings for 8300 Series of adapters.
o updated PCI_VENDOR_ID_QLOGIC and PCI_DEVICE_ID_824X for 8200
Series adapter.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable Interrupt coalescing through ethtool on 83xx adapter.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Read eSwitch statistics from adapter and display them as part
of ethtool statistics.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Disabling PAUSE requires access to EPORT registers,
which may cause a wedge, if EPORT is in reset.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add logs for various failure conditions during channel configuration.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c
The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.
The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.
An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.
Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.
Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.
Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Autoneg is supported on specific port types only. Fix the driver to advertise
autoneg based on the port type.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Fix the driver to drop error frames in the receive path
o Update error counter which was not getting incremented
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o When mailbox interrupt is disabled PF should be
able to process request from VF. Enable polling
for such cases.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Do not disable mailbox interrupts while running
loopback test through SR-IOV PF.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add support for VLAN id configuration per VF using
iproute2 tool.
o VLAN id's 1-4094 are treated as PVID by the PF and
Guest VLAN tagging is not allowed by default.
o PVID is disabled when the VLAN id is set to 0
o Guest VLAN tagging is allowed when the VLAN id is set to 4095.
o Only one Guest VLAN id is supported.
o VLAN id can be changed only when the VF driver is not loaded.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add support for MAC address and Tx rate configuration
per VF via iproute2 tool.
o Tx rate change is allowed while the guest is running
and the VF driver is loaded.
o MAC address change is allowed only when VF driver
is not loaded.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Implement recovery mechanism for VF to recover from
adapter resets.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o FLR from Hypervisor - When hypervisor issues a VF FLR request,
adapter notifies the parent PF driver of the FLR request for PF
driver to perform any cleanup on behalf of that VF.
o FLR from VF Driver - VF driver may initiate a VF FLR request,
if VF state needs to be cleaned up before a re-initialization.
VF re-initialization during kdump is an example.
o PF driver cleans up all resources allocated on behalf of a VF,
on VF FLR notifications from the adapter or from the VF driver.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 82xx adapter requires VLAN id in little endian format.
Instead of passing vlan id parameter as __le16, pass the
parameter as u16 and use cpu_to_le16 at appropriate places.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the encapsulation protocol value a property of VLAN devices and change
the device lookup functions to take the protocol value into account.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Debug logs were not matching with code functionality.
o Changed dev_info to netdev_err
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver receives a packet with gso size > 0 and when TSO is disabled,
it should be transmitted as a TSO packet to prevent Tx timeout and subsequent
firmware reset.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before conducting loopback test by sending packets, driver should stop transmit
queue and turn off carrier.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Commit 319ecf121e
("qlcnic: 83xx sysfs routines") introduced regression
for beaconing test while refactoring 82xx code. This patch is to
revert code to fix beaconing test for 82xx adapter.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
warning: 'pf_info.max_tx_ques' may be used uninitialized in this function
[-Wmaybe-uninitialized]
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Fix for smatch tool reported error
drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c:2029
qlcnic_probe() error: potential NULL dereference 'adapter'.
o While returning from an error path in probe, adapter is not
initialized. So do not access adapter in cleanup path.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[net-next:master 301/302] drivers/net/ethernet/qlogic/qlcnic/qlcnic_hw.c:563
qlcnic_set_multi() error: potential null dereference 'cur'. (kzalloc returns null)
o Break out of the loop after memory allocation failure. Program all the
MAC addresses that were cached in the return path.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o VFs might get scheduled out after sending a command to a PF
and scheduled in after receiving a response. Implement a
worker thread to handle atomic commands.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add support for commands from VF to PF.
o PF validates the commands sent by the VF before sending
it to adapter.
o vPort is a container of resources. PF creates vPort
for VFs and attach resources to it. vPort is
transparent to the VF.
o Separate 83xx TX and RX hardware resource cleanup from 82xx.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Adapter provides communication channel between VF and PF.
Any control commands from the VF driver are sent to the PF driver
through this communication channel. PF driver validates the
commands before sending them to the adapter. Similarly PF driver
forwards any control command responses to the VF driver
through this communication channel. Adapter sends message pending
event to VF or PF when there is an outstanding response or a command
for VF or PF respectively. When a command or a response is sent over
a channel VF or PF cannot send another command or a response
until adapter sends a channel free event. Adapter allocates 1K area to
VF and PF each for this communication.
o Commands and responses are encapsulated in a header. Header determines
sequence id, number of fragments, fragment number etc.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o VF will use shared MSI-X interrupt vector for Tx and Rx.
o When QLCNIC_INTR_SHARED flag is set Tx and Rx will
share MSI-X interrupt vector. Tx will use a separate
MSI-X interrupt vector from Rx otherwise.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add PCI device entry for VF.
o Add HW operations for VF.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add QLCNIC_SRIOV to Kconfig.
o Provide PCI sysfs hooks to enable and disable SR-IOV.
o Allow enabling only when CONFIG_QLCNIC_SRIOV is defined.
o qlcnic_sriov_pf.c has all the PF related SR-IOV
functionality.
o qlcnic_sriov_common.c has VF functionality and SR-IOV
functionality which is common between VF and PF.
o qlcnic_sriov.h is a common header file for SR-IOV defines.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o When interface is down, mailbox command to get context statistics
fails. So restrict driver from issuing get statistics command when
interface is down.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 83xx adapter does not support MSI interrupts, display
warning whenever module parameter is used to load driver
in MSI mode.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Due to improper data type of variable "type", interrupt resources were
not getting deleted in hardware which was causing resource exhaustion
in hardware. Hence mailbox command fails after some iterations of context change.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the number of calls required to alloc
a zeroed block of memory.
Trivially reduces overall object size.
Other changes around these removals
o Neaten call argument alignment
o Remove an unnecessary OOM message after dma_alloc_coherent failure
o Remove unnecessary gfp_t stack variable
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replace ip_fast_csum with csum_replace2 to save cpu cycles
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows LRO aggregation on bonded devices that contain an
NX3031 device. It also adds a for_each_netdev_in_bond_rcu(bond, slave)
macro which executes for each slave that has bond as master.
V3: After testing and discussing this with Rajesh, I decided to keep the
vlan ip cache and just rename it to ip_cache since it will store bond
ip addresses too. A new master flag has been added to the ip cache to
denote that the address has been added because of a master device.
I've taken care of the enslave/release cases by checking for various
combinations of events and flags (e.g. netxen has a master, it's a
bond master and it's not marked as a slave means it is being enslaved
and is dev_open()ed in bond_enslave).
I've changed netxen_free_ip_list() to have a "master" parameter which
causes all IP addresses marked as master to be deleted (used when a
netxen is being released). I've made the patch use the new upper
device API as well. The following cases were tested:
- bond -> netxen
- vlan -> netxen
- vlan -> bond -> netxen
V2: Remove local ip caching, retrieve addresses dynamically and
restore them if necessary.
Note: Tested with NX3031 adapter.
Tested-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Andy Gospodarek <agospoda@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QLogic applications use these callbacks to perform
o NIC Partitioning (NPAR) configuration and management
o Diagnostic tests
o Flash access and updates
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emitting netdev_alloc_skb and netdev_alloc_skb_ip_align OOM
messages is unnecessary as there is already a dump_stack
after allocation failures.
Other trivial changes around these removals:
Convert a few comparisons of pointer to 0 to !pointer.
Change flow to remove unnecessary label.
Remove now unused variable.
Hoist assignment from if.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Properly fill statistics data into buffer.
Update buffer pointer properly after filling statistics data into buffer.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add support for LED test on 83xx series adapters
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Split mailbox structure elements on boundary of adapter
register size i.e. 32bit.
o Shuffle the position of structure elements based on CPU endianness.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow qlcnic to use the generic fdb handler when the driver options
are not enabled. Untill the driver is fully fixed, this allows
the use of the FDB interface with qlogic driver, but simply puts
the driver into promisc mode since the driver currently does not
support IFF_UNICAST_FLT.
CC: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: linux-driver@qlogic.com
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) ping_err() ICMP error handler looks at wrong ICMP header, from Li
Wei.
2) TCP socket hash function on ipv6 is too weak, from Eric Dumazet.
3) netif_set_xps_queue() forgets to drop mutex on errors, fix from
Alexander Duyck.
4) sum_frag_mem_limit() can deadlock due to lack of BH disabling, fix
from Eric Dumazet.
5) TCP SYN data is miscalculated in tcp_send_syn_data(), because the
amount of TCP option space was not taken into account properly in
this code path. Fix from yuchung Cheng.
6) MLX4 driver allocates device queues with the wrong size, from Kleber
Sacilotto.
7) sock_diag can access past the end of the sock_diag_handlers[] array,
from Mathias Krause.
8) vlan_set_encap_proto() makes incorrect assumptions about where
skb->data points, rework the logic so that it works regardless of
where skb->data happens to be. From Jesse Gross.
9) Fix gianfar build failure with NET_POLL enabled, from Paul
Gortmaker.
10) Fix Ipv4 ID setting and checksum calculations in GRE driver, from
Pravin B Shelar.
11) bgmac driver does:
int i;
for (i = 0; ...; ...) {
...
for (i = 0; ...; ...) {
effectively corrupting the outer loop index, use a seperate
variable for the inner loops. From Rafał Miłecki.
12) Fix suspend bugs in smsc95xx driver, from Ming Lei.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
usbnet: smsc95xx: rename FEATURE_AUTOSUSPEND
usbnet: smsc95xx: fix broken runtime suspend
usbnet: smsc95xx: fix suspend failure
bgmac: fix indexing of 2nd level loops
b43: Fix lockdep splat on module unload
Revert "ip_gre: propogate target device GSO capability to the tunnel device"
IP_GRE: Fix GRE_CSUM case.
VXLAN: Use tunnel_ip_select_ident() for tunnel IP-Identification.
IP_GRE: Fix IP-Identification.
net/pasemi: Fix missing coding style
vmxnet3: fix ethtool ring buffer size setting
vmxnet3: make local function static
bnx2x: remove dead code and make local funcs static
gianfar: fix compile fail for NET_POLL=y due to struct packing
vlan: adjust vlan_set_encap_proto() for its callers
sock_diag: Simplify sock_diag_handlers[] handling in __sock_diag_rcv_msg
sock_diag: Fix out-of-bounds access to sock_diag_handlers[]
vxlan: remove depends on CONFIG_EXPERIMENTAL
mlx4_en: fix allocation of CPU affinity reverse-map
mlx4_en: fix allocation of device tx_cq
...
Pull trivial tree from Jiri Kosina:
"Assorted tiny fixes queued in trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (22 commits)
DocBook: update EXPORT_SYMBOL entry to point at export.h
Documentation: update top level 00-INDEX file with new additions
ARM: at91/ide: remove unsused at91-ide Kconfig entry
percpu_counter.h: comment code for better readability
x86, efi: fix comment typo in head_32.S
IB: cxgb3: delay freeing mem untill entirely done with it
net: mvneta: remove unneeded version.h include
time: x86: report_lost_ticks doesn't exist any more
pcmcia: avoid static analysis complaint about use-after-free
fs/jfs: Fix typo in comment : 'how may' -> 'how many'
of: add missing documentation for of_platform_populate()
btrfs: remove unnecessary cur_trans set before goto loop in join_transaction
sound: soc: Fix typo in sound/codecs
treewide: Fix typo in various drivers
btrfs: fix comment typos
Update ibmvscsi module name in Kconfig.
powerpc: fix typo (utilties -> utilities)
of: fix spelling mistake in comment
h8300: Fix home page URL in h8300/README
xtensa: Fix home page URL in Kconfig
...
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Use correct function to clear loopback mode.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete the MAC address of a VM, from the adapter's embedded switch,
after the VM had been migrated out of this adapter/server.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set gso_size to MSS obtained from adapter to avoid incorrect estimation
of receive MSS, which would lead to delayed ACKs in some traffic patterns
Example:
Send two or three packets and wait for ack and only then send
remaining packets.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Cleanly seperate 83xx Legacy interrupt handling code from 82xx
o Update 83xx Legacy interrupt handling code to match with the spec
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Config interrupt is not needed for mailbox interrupts.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added detailed error messages for FW CDRP command failure
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a user adds bridge neighbors, allow him to specify VLAN id.
If the VLAN id is not specified, the neighbor will be added
for VLANs currently in the ports filter list. If no VLANs are
configured on the port, we use vlan 0 and only add 1 entry.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
The bnx2x gso_type setting bug fix in 'net' conflicted with
changes in 'net-next' that broke the gso_* setting logic
out into a seperate function, which also fixes the bug in
question. Thus, use the 'net-next' version.
Signed-off-by: David S. Miller <davem@davemloft.net>
o Do not read mailbox registers on timeout
o Add a helper function to handle mailbox response
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Handle async events during diagnostic loopback test
o Clear loopback mode on failure to receive async events
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanly separate 83xx diagnostic IRQ test from 82xx
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanly separate 83xx diagnostic loopback test routines from 82xx
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a helper routine to handle async events, as it is being called
from multiple places
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver needs to stop participating in firmware based Inter Driver
Communication (IDC) while unloading driver
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register for firmware based Inter Driver Communication (IDC) using initialize
NIC as the first mailbox command
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic set gso_size but not gso type. This leads to crashes
in macvtap.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
For the affected mallocs around these OOM messages:
Converted kmallocs with multiplies to kmalloc_array.
Converted a kmalloc/memcpy to kmemdup.
Removed now unused stack variables.
Removed unnecessary parentheses.
Neatened alignment.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commits 9d11bd159
("wimax: Remove unnecessary alloc/OOM messages, alloc cleanups")
and b2adaca92
("ethernet: Remove unnecessary alloc/OOM messages, alloc cleanups")
added a couple of unused variable warnings.
Remove the now unused variables.
Noticed-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently refactored the driver source, this patch will take care of
updating copyright date and adding it to newly added files.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We actually store the MAC address as well as the board_name here. The
longest board_name is 75 characters so there is more than enough room
to hold the 17 character MAC and the ": " divider. But making this
buffer larger silences a static checker warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-By: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o ipv4 address was not getting programmed properly because of
improper byte order conversion
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
Providing communication channel between KVM and e-Switch so that it
can be informed when hypervisor configures a MAC address and VLAN.
qlcnic_mac_learn module param usage will be changed to:
0 = MAC learning is disable
1 = Driver learning is enable
2 = FDB learning is enable
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide port number in command payload for LED/Beaconing tests.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Some adapter types do not support co-existence of Legacy Interrupt with
MSI-x or MSI among multiple functions. For those adapters, prevent attaching
to a function during normal load, if MSI-x or MSI vectors are not available.
o Using module parameters use_msi=0 and use_msi_x=0, driver can be loaded in
legacy mode for all functions in the adapter.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o This patch enables RSS for TYPE-C packets to enable RSS for TCP over IPv6
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Paasch found netxen could trigger a BUG in its dismantle
phase, in netxen_release_tx_buffer(), using full size TSO packets.
cmd_buf->frag_count includes the skb->data part, so the loop must
start at index 1 instead of 0, or else we can make an out
of bound access to cmd_buff->frag_array[MAX_SKB_FRAGS + 2]
Christoph provided the fixes in netxen_map_tx_skb() function.
In case of a dma mapping error, its better to clear the dma fields
so that we don't try to unmap them again in netxen_release_tx_buffer()
Reported-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/networking/ip-sysctl.txt
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
Both conflicts were simply overlapping context.
A build fix for qlcnic is in here too, simply removing the added
devinit annotations which no longer exist.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is werid that qlge driver supports NETIF_F_TSO6 but
not NETIF_F_IPV6_CSUM. This also causes some kernel warning [1]
when VLAN device setups on a qlge interface.
I think the qlge hardware doesn't support NETIF_F_IPV6_CSUM,
so we have to just remove the NETIF_F_TSO6 flag.
After this patch, the TCP/IPv6 traffic becomes normal again,
no kernel warnings any more.
NOTE: I only tested it on 2.6.32 kernel, even if the upstream
kernel could fix this automatically (it is hard to track NETIF*
flags), removing it is also safe.
1. https://bugzilla.redhat.com/show_bug.cgi?id=891839
Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Cc: linux-driver@qlogic.com
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
rcu_read_lock was missing here
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following error reported by kbuild test robot.
static declaration of 'qlcnic_restore_indev_addr' follows
non-static declaration.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable 83xx virtual NIC mode
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flash template provides instructions to stop, restart and initalize the
firmware. These instructions are abstracted as a series of read, write and
poll operations on hardware registers. Register information and operation
specifics are not exposed to the driver. Driver reads the template from
flash and executes the instructions located at pre-defined offsets.
Template based firmware reset recovery and initialization mechanism minimize
driver changes as firmware evolves.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inter Driver Communication (IDC) module.
CNA function drivers(ISCSI, FCOE and NIC) which shares the adapter
relies on IDC mechanism for gracefull shut down, restart and
firmware error recovery.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
83xx adapter flash memory map, data structures and interface routines
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable base 83xx adapter driver.
Common driver interface routines like probe,
interface up/down routines, irq and resource
allocation routines are modified to add support for 83xx
adapter.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor 82xx driver to support new adapter - Qlogic 83XX CNA
Use QLC_SHARED_REG_RD32 and QLC__SHARED_REG_WR32 macros
for 82xx and 83xx common register access.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor 82xx driver to support new adapter - Qlogic 83XX CNA
Create adapter abstraction layer and seperate 82xx hardware access routines.
Create mailbox based HW interface mechanism
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic_hw.c:370: warning: variable cmd_desc set but not used
qlcnic_hw.c:368: warning: variable consumer set but not used
qlcnic_main.c:448: warning: variable ref_count set but not used
qlcnic_main.c:534: warning: variable mem_base set but not used
qlcnic_ctx.c:137: warning: variable tmp_tmpl set but not used
qlcnic_ctx.c:133: warning: variable version set but not used
qlcnic_minidump.c:200: warning: variable opcode set but not used
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Himanshu Madhani