The device stores flood records in a singly linked list where each
record stores up to three IPv4 addresses of remote VTEPs. The test
verifies that packets are correctly flooded in various cases such as
deletion of a record in the middle of the list.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test various aspects of VxLAN offloading which are specific to mlxsw,
such as sanitization of invalid configurations and offload indication.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simple wrapper reruns the VXLAN ping test with a port number of
8472.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that when decapsulating from VXLAN, the values of inner and outer
TOS are handled appropriately. Because VXLAN driver on its own won't
produce the arbitrary TOS combinations necessary to test this feature,
simply open-code a single ICMP packet and have mausezahn assemble it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that ECN bits in the VXLAN envelope are correctly deduced from the
overlay packet.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that TOS is inherited from the tunneled packet into the envelope as
configured at the VXLAN device.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tests whether TTL of VXLAN envelope packets is properly set based
on the device configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ordering of the topology creation can have impact on whether a
driver is successful in offloading VXLAN. Therefore add a pseudo-test
that reshuffles bits of the topology, and then reruns the same suite of
tests again to make sure that the new setup is supported as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that when sending traffic to a learned MAC address, the traffic is
forwarded accurately only to the right endpoint.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that when sending traffic to an unlearned MAC address, the traffic
is flooded to both remote VXLAN endpoints.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test end-to-end reachability between local and remote endpoints.
Note that because learning is disabled on the VXLAN device, the ICMP
requests will end up being flooded to all remotes.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This skeleton sets up a topology with three VXLAN endpoints: one
"local", possibly offloaded, and two "remote", formed using veth pairs
and likely purely software bridges. The "local" endpoint is connected to
host systems by a VLAN-unaware bridge.
Since VXLAN tunnels must be unique per namespace, each of the "remote"
endpoints is in its own namespace. H3 forms the bridge between the three
domains.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Such a function will be useful for counting malformed packets in the ECN
decap test.
To that end, introduce a common handler for handling stat-fetching, and
reuse it in link_stats_tx_packets_get() and link_stats_rx_errors_get().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the ping routine more generic by allowing passing arbitrary ping
command-line arguments.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have ping_test() recognize an optional argument with a description of
the test. This is handy if there are several ping test, to make it clear
which is which.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to run a certain command inside another network namespace, it's
possible to use "ip netns exec ns command". However then one can't use
functions defined in lib.sh or a test suite.
One option is to do "ip netns exec ns bash -c command", provided that
all functions that one wishes to use (and their dependencies) are
published using "export -f". That may not be practical.
Therefore, introduce a helper in_ns(), which wraps a given command in a
boilerplate of "ip netns exec" and "source lib.sh", thus making all
library functions available. (Custom functions that a script wishes to
run within a namespace still need to be exported.)
Because quotes in "$@" aren't recognized in heredoc, hand-expand the
array in an explicit for loop, leveraging printf %q to handle proper
quoting.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far the case of NUM_NETIFS of 0 has not been interesting. However if
one wishes to reuse the lib.sh routines in a setup of a separate
namespace, being able to import like this is handy.
Therefore replace the {1..$NUM_NETIFS} references, which cause iteration
over 1 and 0, with an explicit for loop like we do in setup_wait() and
tc_offload_check(), so that for NUM_NETIFS of 0 no iteration is done.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix some potentially uninitialized variables and use-after-free in
kvaser_usb can drier, from Jimmy Assarsson.
2) Fix leaks in qed driver, from Denis Bolotin.
3) Socket leak in l2tp, from Xin Long.
4) RSS context allocation fix in bnxt_en from Michael Chan.
5) Fix cxgb4 build errors, from Ganesh Goudar.
6) Route leaks in ipv6 when removing exceptions, from Xin Long.
7) Memory leak in IDR allocation handling of act_pedit, from Davide
Caratti.
8) Use-after-free of bridge vlan stats, from Nikolay Aleksandrov.
9) When MTU is locked, do not force DF bit on ipv4 tunnels. From
Sabrina Dubroca.
10) When NAPI cached skb is reused, we must set it to the proper initial
state which includes skb->pkt_type. From Eric Dumazet.
11) Lockdep and non-linear SKB handling fix in tipc from Jon Maloy.
12) Set RX queue properly in various tuntap receive paths, from Matthew
Cover.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tuntap: fix multiqueue rx
ipv6: Fix PMTU updates for UDP/raw sockets in presence of VRF
tipc: don't assume linear buffer when reading ancillary data
tipc: fix lockdep warning when reinitilaizing sockets
net-gro: reset skb->pkt_type in napi_reuse_skb()
tc-testing: tdc.py: Guard against lack of returncode in executed command
tc-testing: tdc.py: ignore errors when decoding stdout/stderr
ip_tunnel: don't force DF when MTU is locked
MAINTAINERS: Add entry for CAKE qdisc
net: bridge: fix vlan stats use-after-free on destruction
socket: do a generic_file_splice_read when proto_ops has no splice_read
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
Revert "net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs"
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
net/sched: act_pedit: fix memory leak when IDR allocation fails
net: lantiq: Fix returned value in case of error in 'xrx200_probe()'
ipv6: fix a dst leak when removing its exception
net: mvneta: Don't advertise 2.5G modes
drivers/net/ethernet/qlogic/qed/qed_rdma.h: fix typo
net/mlx4: Fix UBSAN warning of signed integer overflow
...
- Address Range Scrub overflow continuation handling has been broken
since it was initially merged. It was only recently that error injection
and platform-BIOS support enabled this corner case to be exercised.
- The recent attempt to provide more isolation for the kernel Address
Range Scrub state machine from userapace initiated sessions triggers a
lockdep report. Revert and try again at the next merge window.
- Fix a kasan reported buffer overflow in libnvdimm unit test
infrastrucutre (nfit_test)
-----BEGIN PGP SIGNATURE-----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=sfNx
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-fixes-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A small batch of fixes for v4.20-rc3.
The overflow continuation fix addresses something that has been broken
for several releases. Arguably it could wait even longer, but it's a
one line fix and this finishes the last of the known address range
scrub bug reports. The revert addresses a lockdep regression. The unit
tests are not critical to fix, but no reason to hold this fix back.
Summary:
- Address Range Scrub overflow continuation handling has been broken
since it was initially merged. It was only recently that error
injection and platform-BIOS support enabled this corner case to be
exercised.
- The recent attempt to provide more isolation for the kernel Address
Range Scrub state machine from userapace initiated sessions
triggers a lockdep report. Revert and try again at the next merge
window.
- Fix a kasan reported buffer overflow in libnvdimm unit test
infrastrucutre (nfit_test)"
* tag 'libnvdimm-fixes-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
Revert "acpi, nfit: Further restrict userspace ARS start requests"
acpi, nfit: Fix ARS overflow continuation
tools/testing/nvdimm: Fix the array size for dimm devices.
Add some defensive coding in case one of the subprocesses created by tdc
returns nothing. If no object is returned from exec_cmd, then tdc will
halt with an unhandled exception.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent exceptions from being raised while decoding output
from an executed command. There is no impact on tdc's
execution and the verify command phase would fail the pattern
match.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This covers for proper accounting of encap needed static keys
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two weeks worth of fixes since rc1.
- I broke 16-byte alignment of the stack when we moved PPR into pt_regs.
Despite being required by the ABI this broke almost nothing, we eventually
hit it in code where GCC does arithmetic on the stack pointer assuming the
bottom 4 bits are clear. Fix it by padding the in-kernel pt_regs by 8 bytes.
- A couple of commits fixing minor bugs in the recent SLB rewrite.
- A build fix related to tracepoints in KVM in some configurations.
- Our old "IO workarounds" code written for Cell couldn't coexist in a kernel
that runs on Power9 with the Radix MMU, fix that.
- Remove the NPU DMA ops, these just printed a warning and should never have
been called.
- Suppress an overly chatty message triggered by CPU hotplug in some configs.
- Two small selftest fixes.
Thanks to:
Alistair Popple, Gustavo Romero, Nicholas Piggin, Satheesh Rajendran, Scott Wood.
-----BEGIN PGP SIGNATURE-----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=fEqA
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Two weeks worth of fixes since rc1.
- I broke 16-byte alignment of the stack when we moved PPR into
pt_regs. Despite being required by the ABI this broke almost
nothing, we eventually hit it in code where GCC does arithmetic on
the stack pointer assuming the bottom 4 bits are clear. Fix it by
padding the in-kernel pt_regs by 8 bytes.
- A couple of commits fixing minor bugs in the recent SLB rewrite.
- A build fix related to tracepoints in KVM in some configurations.
- Our old "IO workarounds" code written for Cell couldn't coexist in
a kernel that runs on Power9 with the Radix MMU, fix that.
- Remove the NPU DMA ops, these just printed a warning and should
never have been called.
- Suppress an overly chatty message triggered by CPU hotplug in some
configs.
- Two small selftest fixes.
Thanks to: Alistair Popple, Gustavo Romero, Nicholas Piggin, Satheesh
Rajendran, Scott Wood"
* tag 'powerpc-4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Adjust wild_bctr to build with old binutils
powerpc/64: Fix kernel stack 16-byte alignment
powerpc/numa: Suppress "VPHN is not supported" messages
selftests/powerpc: Fix wild_bctr test to work on ppc64
powerpc/io: Fix the IO workarounds code to work with Radix
powerpc/mm/64s: Fix preempt warning in slb_allocate_kernel()
KVM: PPC: Move and undef TRACE_INCLUDE_PATH/FILE
powerpc/mm/64s: Only use slbfee on CPUs that support it
powerpc/mm/64s: Use PPC_SLBFEE macro
powerpc/mm/64s: Consolidate SLB assertions
powerpc/powernv/npu: Remove NPU DMA ops
Track the basic codepaths of delta handling, using objagg tracepoints.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for this to behave as required with delta bits, change the mask
for rule with handle 103.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for this to behave as required with delta bits, change the mask
for rule with handle 103.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the selftest wild_bctr can fail to build when an old gcc is
used, notably on gcc using a binutils version <= 2.27, because the
assembler does not support the integer suffix UL.
This patch adjusts the wild_bctr test so the REG_POISON value is still
treated as an unsigned long for the shifts on compilation but the UL
suffix is absent on the stringification, so the inline asm code
generated has no UL suffixes.
Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
[mpe: Wrap long line]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The selftest I recently added to test branching to an out-of-bounds
NIP doesn't work on 64-bit big endian. It does fail but not in the
right way. That is it SEGVs trying to load from the opd at BAD_NIP,
but it never gets as far as branching to BAD_NIP.
To fix it we need to create an opd which is reachable but which holds
the bad address.
Fixes: b7683fc66e ("selftests/powerpc: Add a test of wild bctr")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Introduce eight tests, for FoU and GUE, with IPv4 and IPv6 payload,
on IPv4 and IPv6 transport, that check that PMTU exceptions are created
with the right value when exceeding the MTU on a link of the path.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a router between endpoints, implemented via namespaces, set a low MTU
between router and destination endpoint, exceed it and check PMTU value in
route exceptions.
v2:
- Introduce IPv4 tests right away, if iproute2 doesn't support the 'df'
link option they will be skipped (David Ahern)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a router between endpoints, implemented via namespaces, set a low MTU
between router and destination endpoint, exceed it and check PMTU value in
route exceptions.
v2:
- Change all occurrences of VxLAN to VXLAN (Jiri Benc)
- Introduce IPv4 tests right away, if iproute2 doesn't support the 'df'
link option they will be skipped (David Ahern)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends the existing udp programs to allow checking for proper
GRO aggregation/GSO size, and run the tests via a shell script, using
a veth pair with XDP program attached to trigger the GRO code path.
rfc v3 -> v1:
- use ip route to attach the xdp helper to the veth
rfc v2 -> rfc v3:
- add missing test program options documentation
- fix sporatic test failures (receiver faster than sender)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Run on top of veth pair, using a dummy XDP program to enable the GRO.
rfc v3 -> v1:
- use ip route to attach the xdp helper to the veth
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This trivial XDP program does nothing, but will be used by the
next patch to test the GRO path in a net namespace, leveraging
the veth XDP implementation.
It's added here, despite its 'net' usage, to avoid the duplication
of the llc-related makefile boilerplate.
rfc v3 -> v1:
- move the helper implementation into the bpf directory, don't
touch udpgso_bench_rx
rfc v2 -> rfc v3:
- move 'x' option handling here
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And fix a couple of buglets (port option processing,
clean termination on SIGINT). This is preparatory work
for GRO tests.
rfc v2 -> rfc v3:
- use ETH_MAX_MTU
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel PT sql viewer: (Adrian Hunter)
- Fall back to /usr/local/lib/libxed.so
- Add Selected branches report
- Add help window
- Fix table find when table re-ordered
Intel PT debug log (Adrian Hunter)
- Add more event information
- Add MTC and CYC timestamps
perf record: (Andi Kleen)
- Support weak groups, just like with 'perf stat'
perf trace: (Arnaldo Carvalho de Melo)
- Start augmenting raw_syscalls:{sys_enter,sys_exit}: goal is to have a
generic, arch independent eBPF kernel component that is programmed with
syscall table details, what to copy, how many bytes, pid, arg filters from the
userspace via eBPF maps by the 'perf trace' tool that continues to use all its
argument beautifiers, just taking advantage of the extra pointer contents.
JVMTI: (Gustavo Romero)
- Fix undefined symbol scnprintf in libperf-jvmti.so
perf top: (Jin Yao)
- Display the LBR stats in callchain entries
perf stat: (Thomas Richter)
- Handle different PMU names with common prefix
arm64: Will (Deacon)
- Fix arm64 tools build failure wrt smp_load_{acquire,release}.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCW+GBMAAKCRCyPKLppCJ+
J5hwAP9+7F2HKvjwHj4g6YeAvCp2WzXbO9UzakfTNtkAwWDZHwD/aN8T8RdgiaCm
FqlDoftwvSQSpbKvaiN7M1GSk14a+AQ=
=gWMp
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo-4.20-20181106' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent improvements and fixes from Arnaldo Carvalho de Melo:
Intel PT SQL viewer: (Adrian Hunter)
- Fall back to /usr/local/lib/libxed.so
- Add Selected branches report
- Add help window
- Fix table find when table re-ordered
Intel PT debug log (Adrian Hunter)
- Add more event information
- Add MTC and CYC timestamps
perf record: (Andi Kleen)
- Support weak groups, just like with 'perf stat'
perf trace: (Arnaldo Carvalho de Melo)
- Start augmenting raw_syscalls:{sys_enter,sys_exit}: goal is to have a
generic, arch independent eBPF kernel component that is programmed with
syscall table details, what to copy, how many bytes, pid, arg filters from the
userspace via eBPF maps by the 'perf trace' tool that continues to use all its
argument beautifiers, just taking advantage of the extra pointer contents.
JVMTI: (Gustavo Romero)
- Fix undefined symbol scnprintf in libperf-jvmti.so
perf top: (Jin Yao)
- Display the LBR stats in callchain entries
perf stat: (Thomas Richter)
- Handle different PMU names with common prefix
arm64: Will (Deacon)
- Fix arm64 tools build failure wrt smp_load_{acquire,release}.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Andi reported following malfunction:
# perf record -e '{ref-cycles,cycles}:S' -a sleep 1
# perf script
non matching sample_id_all
That's because we disable sample_id_all bit for non-sampling group
members. We can't do that, because it needs to be the same over the
whole event list. This patch keeps it untouched again.
Reported-by: Andi Kleen <andi@firstfloor.org>
Tested-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180923150420.27327-1-jolsa@kernel.org
Fixes: e9add8bac6 ("perf evsel: Disable write_backward for leader sampling group events")
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
KASAN reports following global out of bounds access while
nfit_test is being loaded. The out of bound access happens
the following reference to dimm_fail_cmd_flags[dimm]. 'dimm' is
over than the index value, NUM_DCR (==5).
static int override_return_code(int dimm, unsigned int func, int rc)
{
if ((1 << func) & dimm_fail_cmd_flags[dimm]) {
dimm_fail_cmd_flags[] definition:
static unsigned long dimm_fail_cmd_flags[NUM_DCR];
'dimm' is the return value of get_dimm(), and get_dimm() returns
the index of handle[] array. The handle[] has 7 index. Let's use
ARRAY_SIZE(handle) as the array size.
KASAN report:
==================================================================
BUG: KASAN: global-out-of-bounds in nfit_test_ctl+0x47bb/0x55b0 [nfit_test]
Read of size 8 at addr ffffffffc10cbbe8 by task kworker/u41:0/8
...
Call Trace:
dump_stack+0xea/0x1b0
? dump_stack_print_info.cold.0+0x1b/0x1b
? kmsg_dump_rewind_nolock+0xd9/0xd9
print_address_description+0x65/0x22e
? nfit_test_ctl+0x47bb/0x55b0 [nfit_test]
kasan_report.cold.6+0x92/0x1a6
nfit_test_ctl+0x47bb/0x55b0 [nfit_test]
...
The buggy address belongs to the variable:
dimm_fail_cmd_flags+0x28/0xffffffffffffa440 [nfit_test]
==================================================================
Fixes: 39611e83a2 ("tools/testing/nvdimm: Make DSM failure code injection...")
Signed-off-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently jvmti agent can not be used because function scnprintf is not
present in the agent libperf-jvmti.so. As a result the JVM when using
such agent to record JITed code profiling information will fail on
looking up scnprintf:
java: symbol lookup error: lib/libperf-jvmti.so: undefined symbol: scnprintf
This commit fixes that by reverting to the use of snprintf, that can be
looked up, instead of scnprintf, adding a proper check for the returned
value in order to print a better error message when the jitdump file
pathname is too long. Checking the returned value also helps to comply
with some recent gcc versions, like gcc8, which will fail due to
truncated writing checks related to the -Werror=format-truncation= flag.
Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
LPU-Reference: 1541117601-18937-2-git-send-email-gromero@linux.vnet.ibm.com
Link: https://lkml.kernel.org/n/tip-mvpxxxy7wnzaj74cq75muw3f@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Guenter reported that using ARCH=x86_64 to build perf has regressed:
$ make -C tools/perf O=/tmp/build/perf ARCH=x86_64
make: Entering directory '/home/acme/git/perf/tools/perf'
BUILD: Doing 'make -j4' parallel build
HOSTCC /tmp/build/perf/fixdep.o
HOSTLD /tmp/build/perf/fixdep-in.o
LINK /tmp/build/perf/fixdep
Auto-detecting system features:
... dwarf: [ on ]
<SNIP>
... bpf: [ on ]
GEN /tmp/build/perf/common-cmds.h
make[2]: *** No rule to make target '/home/acme/git/perf/tools/arch/x86_64/include/uapi/asm//mman.h', needed by '/tmp/build/perf/trace/beauty/generated/mmap_flags_array.c'. Stop.
make[2]: *** Waiting for unfinished jobs....
PERF_VERSION = 4.19.gf6c23e3
make[1]: *** [Makefile.perf:207: sub-make] Error 2
make: *** [Makefile:70: all] Error 2
make: Leaving directory '/home/acme/git/perf/tools/perf'
$
This is because we must use $(SRCARCH) where we were using $(ARCH), so
that, just like the top level Makefile, we get this done:
# Additional ARCH settings for x86
ifeq ($(ARCH),i386)
SRCARCH := x86
endif
ifeq ($(ARCH),x86_64)
SRCARCH := x86
endif
Which is done in tools/scripts/Makefile.arch, so switch to use
$(SRCARCH).
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Clark Williams <williams@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Fixes: fbd7458db7 ("perf beauty: Wire up the mmap flags table generator to the Makefile")
Link: https://lkml.kernel.org/r/20181105184612.GD7077@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
One cause of decoding errors is un-synchronized side-band data.
Timestamps are needed to debug such cases. TSC packet timestamps are
logged. Log also MTC and CYC timestamps.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: http://lkml.kernel.org/r/20181105073505.8129-3-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Table rows can be re-ordered by selecting a column to sort by. After
re-ordering, the "find" operation was highlighting the wrong row, fix
it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20181104151238.15947-5-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add a window to display help. It is also possible to display the help
only, by using the option "--help-only" instead of a database name.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20181104151238.15947-4-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fetching data from the database can be slow. Add a report that provides
the ability to select a subset of branches.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20181104151238.15947-3-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fall back to /usr/local/lib/libxed.so to cater for distributions that do
not have /usr/local/lib in the library path by default.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20181104151238.15947-2-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
On s390 the CPU Measurement Facility for counters now supports
2 PMUs named cpum_cf (CPU Measurement Facility for counters) and
cpum_cf_diag (CPU Measurement Facility for diagnostic counters)
for one and the same CPU.
Running command
[root@s35lp76 perf]# ./perf stat -e tx_c_tend \
-- ~/mytests/cf-tx-events 1
Measuring transactions
TX_C_TABORT_NO_SPECIAL: 0 expected:0
TX_C_TABORT_SPECIAL: 0 expected:0
TX_C_TEND: 1 expected:1
TX_NC_TABORT: 11 expected:11
TX_NC_TEND: 1 expected:1
Performance counter stats for '/root/mytests/cf-tx-events 1':
2 tx_c_tend
0.002120091 seconds time elapsed
0.000121000 seconds user
0.002127000 seconds sys
[root@s35lp76 perf]#
displays output which is unexpected (and wrong):
2 tx_c_tend
The test program definitely triggers only one transaction, as shown
in line 'TX_C_TEND: 1 expected:1'.
This is caused by the following call sequence:
pmu_lookup() scans and installs a PMU.
+--> pmu_aliases() parses all aliases in directory
.../<pmu-name>/events/* which are file names.
+--> pmu_aliases_parse() Read each file in directory and create
an new alias entry. This is done with
+--> perf_pmu__new_alias() and
+--> __perf_pmu__new_alias() which also check for
identical alias names.
After pmu_aliases() returns, a complete list of event names
for this pmu has been created. Now function
pmu_add_cpu_aliases() is called to add the events listed in the json
| files to the alias list of the cpu.
+--> perf_pmu__find_map() Returns a pointer to the json events.
Now function pmu_add_cpu_aliases() scans through all events listed
in the JSON files for this CPU.
Each json event pmu name is compared with the current PMU being
built up and if they mismatch, the json event is added to the
current PMUs alias list.
To avoid duplicate entries the following comparison is done:
if (!is_arm_pmu_core(name)) {
pname = pe->pmu ? pe->pmu : "cpu";
if (strncmp(pname, name, strlen(pname)))
continue;
}
The culprit is the strncmp() function.
Using current s390 PMU naming, the first PMU is 'cpum_cf'
and a long list of events is added, among them 'tx_c_tend'
When the second PMU named 'cpum_cf_diag' is added, only one event
named 'CF_DIAG' is added by the pmu_aliases() function.
Now function pmu_add_cpu_aliases() is invoked for PMU 'cpum_cf_diag'.
Since the CPUID string is the same for both PMUs, json file events
for PMU named 'cpum_cf' are added to the PMU 'cpm_cf_diag'
This happens because the strncmp() actually compares:
strncmp("cpum_cf", "cpum_cf_diag", 6);
The first parameter is the pmu name taken from the event in
the json file. The second parameter is the pmu name of the PMU
currently being built.
They are different, but the length of the compare only tests the
common prefix and this returns 0(true) when it should return false.
Now all events for PMU cpum_cf are added to the alias list for pmu
cpum_cf_diag.
Later on in function parse_events_add_pmu() the event 'tx_c_end' is
searched in all available PMUs and found twice, adding it two
times to the evsel_list global variable which is the root
of all events. This results in a counter value of 2 instead
of 1.
Output with this patch:
[root@s35lp76 perf]# ./perf stat -e tx_c_tend \
-- ~/mytests/cf-tx-events 1
Measuring transactions
TX_C_TABORT_NO_SPECIAL: 0 expected:0
TX_C_TABORT_SPECIAL: 0 expected:0
TX_C_TEND: 1 expected:1
TX_NC_TABORT: 11 expected:11
TX_NC_TEND: 1 expected:1
Performance counter stats for '/root/mytests/cf-tx-events 1':
1 tx_c_tend
0.001815365 seconds time elapsed
0.000123000 seconds user
0.001756000 seconds sys
[root@s35lp76 perf]#
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Reviewed-by: Sebastien Boisvert <sboisvert@gydle.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: stable@vger.kernel.org
Fixes: 292c34c102 ("perf pmu: Fix core PMU alias list for X86 platform")
Link: http://lkml.kernel.org/r/20181023151616.78193-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Ido Schimmel