eSDHC is not a standard SD host controller. SDHCI_CAPABILITIES_1
register address is 0x44 while it's 0x114 (ESDHC_CAPABILITIES_1)
for eSDHC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC can only DMA from 32-bit-aligned addresses.
This fixes the following test cases of mmc_test:
11: Badly aligned write
12: Badly aligned read
13: Badly aligned multi-block write
14: Badly aligned multi-block read
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC uses tuning block for tuning procedure. So the tuning
block control register must be configured properly before tuning.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC supports signal voltage switch from 3.3v to 1.8v by
eSDHC_PROCTL[VOLT_SEL] bit. This bit changes the value of output
signal SDHC_VS, and there must be a control circuit out of eSDHC
to change the signal voltage according to SDHC_VS output signal.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC could select peripheral clock or platform clock as clock source by
the PCS bit of eSDHC Control Register, and this bit couldn't be reset by
software reset for all. In default, the platform clock is used. But we have
to use peripheral clock since it has a higher frequency to support eMMC
HS200 mode and SD UHS-I mode. This patch is to add peripheral clock support
and use it instead of platform clock if it's declared in eSDHC dts node.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC_PRSSTAT[SDSTB] bit indicates whether the internal card clock is
stable. This bit is for the host driver to poll clock status when changing
the clock frequency. It is recommended to clear eSDHC_SYSCTL[SDCLKEN]
to remove glitch on the card clock when the frequency is changing. This
patch is to disable SDCLKEN bit before changing frequency and enable it
after SDSTB bit is set.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC register definitions in header file were messy and confusing.
This patch is to clean up these definitions.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To support little endian eSDHC controller, we redefine both BE and
LE IO accessors. In the new accessors, use ioread*/iowrite* instead
of in_be32/out_be32 and will select accessors according to endian
mode in probe function.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC supports high speed mode, but has no enabling bit for it.
Add this quirk to avoid writing to eSDHC_PROCTL[DTW] by mistake.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Support for 8BIT bus with was added some time ago to sdhci-esdhc but
then missed to remove the 8BIT from the reserved bit mask which made
8BIT non functional.
Fixes: 66b50a0099 ("mmc: esdhc: Add support for 8-bit bus width and..")
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The Freescale esdhc driver is the only driver which needs the interrupt
registers restored after a reset. Move this quirk to be part of the
ESDHC driver implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
We need a lot of imx6 specific things into common esdhc_set_clock
for support SD3.0 and eMMC DDR mode which is not needed for power pc
platforms, so esdhc_set_clock seems not so common anymore.
Instead of keeping add platform specfics things into this common API,
we choose to move that code into platform driver itself to handle.
This can also exclude the dependency between imx and power pc on this
headfile and is easy for maintain in the future.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support of connecting an MMC media using an 8-bit
bus width connection to Freescale's P2020 H/W SDHC controller. During
the probe function, the generic function mmc_of_parse is called to
detect whether the controller is configured with 8-bit bus width.
Also, the generic function detects if the non-removable property is
set in the device tree. The function esdhc_pltfm_bus_width was added
because the bus width configuration is platform specific.
Signed-off-by: Oded Gabbay <ogabbay@advaoptical.com>
Reviewed-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The SDCLK is divided down from the host controller clock. Host
controller clock may be different from the maximum SDCLK, so
get it from the platform, instead of just using the max SDCLK.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since commit 30832ab56 ("mmc: sdhci: Always pass clock request value
zero to set_clock host op") was merged, esdhc_set_clock starts hitting
"if (clock == 0)" where ESDHC_SYSTEM_CONTROL has been operated. This
causes SDHCI card-detection function being broken. Fix the regression
by moving "if (clock == 0)" above ESDHC_SYSTEM_CONTROL operation.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
1ms is enough for hardware to change the clock to stable.
100ms is too long in the tasklet.
Signed-off-by: Tony Lin <tony.lin@freescale.com>
CC: Xiaobo Xie <X.Xie@freescale.com>
CC: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sdhci-esdhc-imx does not need SDHCI_QUIRK_NO_CARD_NO_RESET.
Make it OF-specific.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
It can be worked around using a GPIO which will be done for i.MX later.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Tested-by: Marc Reilly <marc@cpdesign.com.au>
Tested-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Put everything which can be shared between the OF and platform version
of this driver into a local .h file.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Eric Bénard <eric@eukrea.com>
[cjb: fix compile error: sdhci-esdhc.c->sdhci-esdhc.h]
Signed-off-by: Chris Ball <cjb@laptop.org>
yangbo lu