This DMI quirk turns on "pci=use_crs" for the ALiveSATA2-GLAN because
amd_bus.c doesn't handle this system correctly.
The system has a single HyperTransport I/O chain, but has two PCI host
bridges to buses 00 and 80. amd_bus.c learns the MMIO range associated
with buses 00-ff and that this range is routed to the HT chain hosted at
node 0, link 0:
bus: [00, ff] on node 0 link 0
bus: 00 index 1 [mem 0x80000000-0xfcffffffff]
This includes the address space for both bus 00 and bus 80, and amd_bus.c
assumes it's all routed to bus 00.
We find device 80:01.0, which BIOS left in the middle of that space, but
we don't find a bridge from bus 00 to bus 80, so we conclude that 80:01.0
is unreachable from bus 00, and we move it from the original, working,
address to something outside the bus 00 aperture, which does not work:
pci 0000:80:01.0: reg 10: [mem 0xfebfc000-0xfebfffff 64bit]
pci 0000:80:01.0: BAR 0: assigned [mem 0xfd00000000-0xfd00003fff 64bit]
The BIOS told us everything we need to know to handle this correctly,
so we're better off if we just pay attention, which lets us leave the
80:01.0 device at the original, working, address:
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7f])
pci_root PNP0A03:00: host bridge window [mem 0x80000000-0xff37ffff]
ACPI: PCI Root Bridge [PCI1] (domain 0000 [bus 80-ff])
pci_root PNP0A08:00: host bridge window [mem 0xfebfc000-0xfebfffff]
This was a regression between 2.6.33 and 2.6.34. In 2.6.33, amd_bus.c
was used only when we found multiple HT chains. 3e3da00c01, which
enabled amd_bus.c even on systems with a single HT chain, caused this
failure.
This quirk was written by Graham. If we ever enable "pci=use_crs" for
machines from 2006 or earlir, this quirk should be removed.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16007
Cc: stable@kernel.org
Reported-by: Graham Ramsey <ramsey.graham@ntlworld.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The Linux kernel assigns BARs that a BIOS did not assign, most likely
to handle broken BIOSes that didn't enumerate the devices correctly.
On UV the BIOS purposely doesn't assign I/O BARs for certain devices/
drivers we know don't use them (examples, LSI SAS, Qlogic FC, ...).
We purposely don't assign these I/O BARs because I/O Space is a very
limited resource. There is only 64k of I/O Space, and in a PCIe
topology that space gets divided up into 4k chucks (this is due to
the fact that a pci-to-pci bridge's I/O decoder is aligned at 4k)...
Thus a system can have at most 16 cards with I/O BARs: (64k / 4k = 16)
SGI needs to scale to >16 devices with I/O BARs. So by not assigning
I/O BARs on devices we know don't use them, we can do that (iff the
kernel doesn't go and assign these BARs that the BIOS purposely didn't
assign).
This patch will not assign a resource to a device BAR if that BAR was
not assigned by the BIOS, and the kernel cmdline option 'pci=nobar'
was specified. This patch is closely modeled after the 'pci=norom'
option that currently exists in the tree.
Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pcibios_scan_specific_bus calls pci_scan_bus_on_node which is
__devinit. Mark pcibios_scan_specific_bus __devinit as well since
all users are now __init or __devinit.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, pci, mrst: Add extra sanity check in walking the PCI extended cap chain
x86: Fix x2apic preenabled system with kexec
x86: Force HPET readback_cmp for all ATI chipsets
The fixed bar capability structure is searched in PCI extended
configuration space. We need to make sure there is a valid capability
ID to begin with otherwise, the search code may stuck in a infinite
loop which results in boot hang. This patch adds additional check for
cap ID 0, which is also invalid, and indicates end of chain.
End of chain is supposed to have all fields zero, but that doesn't
seem to always be the case in the field.
Suggested-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <1279306706-27087-1-git-send-email-jacob.jun.pan@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
If we fail to assign resources to a PCI BAR, this patch makes us try the
original address from BIOS rather than leaving it disabled.
Linux tries to make sure all PCI device BARs are inside the upstream
PCI host bridge or P2P bridge apertures, reassigning BARs if necessary.
Windows does similar reassignment.
Before this patch, if we could not move a BAR into an aperture, we left
the resource unassigned, i.e., at address zero. Windows leaves such BARs
at the original BIOS addresses, and this patch makes Linux do the same.
This is a bit ugly because we disable the resource long before we try to
reassign it, so we have to keep track of the BIOS BAR address somewhere.
For lack of a better place, I put it in the struct pci_dev.
I think it would be cleaner to attempt the assignment immediately when the
claim fails, so we could easily remember the original address. But we
currently claim motherboard resources in the middle, after attempting to
claim PCI resources and before assigning new PCI resources, and changing
that is a fairly big job.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16263
Reported-by: Andrew <nitr0@seti.kr.ua>
Tested-by: Andrew <nitr0@seti.kr.ua>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: clear bridge resource range if BIOS assigned bad one
PCI: hotplug/cpqphp, fix NULL dereference
Revert "PCI: create function symlinks in /sys/bus/pci/slots/N/"
PCI: change resource collision messages from KERN_ERR to KERN_INFO
Yannick found that video does not work with 2.6.34. The cause of this
bug was that the BIOS had assigned the wrong range to the PCI bridge
above the video device. Before 2.6.34 the kernel would have shrunk
the size of the bridge window, but since
d65245c PCI: don't shrink bridge resources
the kernel will avoid shrinking BIOS ranges.
So zero out the old range if we fail to claim it at boot time; this will
cause us to allocate a new range at startup, restoring the 2.6.34
behavior.
Fixes regression https://bugzilla.kernel.org/show_bug.cgi?id=16009.
Reported-by: Yannick <yannick.roehlly@free.fr>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/i7core: (83 commits)
i7core_edac: Better describe the supported devices
Add support for Westmere to i7core_edac driver
i7core_edac: don't free on success
i7core_edac: Add support for X5670
Always call i7core_[ur]dimm_check_mc_ecc_err
i7core_edac: fix memory leak of i7core_dev
EDAC: add __init to i7core_xeon_pci_fixup
i7core_edac: Fix wrong device id for channel 1 devices
i7core: add support for Lynnfield alternate address
i7core_edac: Add initial support for Lynnfield
i7core_edac: do not export static functions
edac: fix i7core build
edac: i7core_edac produces undefined behaviour on 32bit
i7core_edac: Use a more generic approach for probing PCI devices
i7core_edac: PCI device is called NONCORE, instead of NOCORE
i7core_edac: Fix ringbuffer maxsize
i7core_edac: First store, then increment
i7core_edac: Better parse "any" addrmask
i7core_edac: Use a lockless ringbuffer
edac: Create an unique instance for each kobj
...
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, cpufeature: Unbreak compile with gcc 3.x
x86, pat: Fix memory leak in free_memtype
x86, k8: Fix section mismatch for powernowk8_exit()
lib/atomic64_test: fix missing include of linux/kernel.h
x86: remove last traces of quicklist usage
x86, setup: Phoenix BIOS fixup is needed on Dell Inspiron Mini 1012
x86: "nosmp" command line option should force the system into UP mode
arch/x86/pci: use kasprintf
x86, apic: ack all pending irqs when crashed/on kexec
kasprintf combines kmalloc and sprintf, and takes care of the size
calculation itself.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression a,flag;
expression list args;
statement S;
@@
a =
- \(kmalloc\|kzalloc\)(...,flag)
+ kasprintf(flag,args)
<... when != a
if (a == NULL || ...) S
...>
- sprintf(a,args);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
LKML-Reference: <201005241913.o4OJDG3R010871@imap1.linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Read the memory ranges behind the Broadcom CNB20LE host bridge out of the
hardware. This allows PCI hotplugging to work, since we know which memory
range to allocate PCI BAR's from.
The x86 PCI code automatically prefers the ACPI _CRS information when it is
available. In that case, this information is not used.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Both ACPI and SFI firmwares will have MCFG space, but the error message
isn't valid on SFI, so don't print the message in that case.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Moorestown PCI code has special handling of devices with fixed BARs. In
case of BAR sizing writes, we need to update the fake PCI MMCFG space with real
size decode value.
When a BAR is not present, we need to return 0 instead of ~0. ~0 will be
treated as device error per bugzilla 12006.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
LKML-Reference: <1273873281-17489-2-git-send-email-jacob.jun.pan@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Do not blindly access extended configuration space unless we actively
know we're on a Moorestown platform. The fixed-size BAR capability
lives in the extended configuration space, and thus is not applicable
if the configuration space isn't appropriately sized.
This fixes booting certain VMware configurations with CONFIG_MRST=y.
Moorestown will add a fake PCI-X 266 capability to advertise the
presence of extended configuration space.
Reported-and-tested-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <AANLkTiltKUa3TrKR1M51eGw8FLNoQJSLT0k0_K5X3-OJ@mail.gmail.com>
This patch adds additional LPC Controller DeviceIDs for the Intel Cougar
Point PCH.
The DeviceIDs are defined and referenced as a range of values, the same
way Ibex Peak was implemented.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_config_lock must be a real spinlock in preempt-rt. Convert it to
raw_spinlock. No change for !RT kernels.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This code changes the detection procedure of i7core_edac. Instead of
directly probing for MC registers, it probes for another register found
on Nehalem. If found, it tries to pick the first MC PCI BUS. This should
work fine with Xeon 35xx, but, on Xeon 55xx, this is at bus 254 and 255
that are not properly detected by the non-legacy PCI methods.
The new detection code scans specifically at buses 254 and 255 for the
Xeon 55xx devices.
This code has not tested yet. After working, a change at the code will
be needed, since the i7core is not yet ready for working with 2 sets of
MC.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a probing code that seeks for an specific pci bus. It
still needs testing, but it is hoped that this will help to identify the
memory controller with Xeon 55xx series.
Signed-off-by: Aristeu Sergio <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ACPI _CRS Address Space Descriptors have _MIN, _MAX, and _LEN. Linux has
been computing Address Spaces as [_MIN to _MIN + _LEN - 1]. Based on the
tests in the bug reports below, Windows apparently uses [_MIN to _MAX].
Per spec (ACPI 4.0, Table 6-40), for _CRS fixed-size, fixed location
descriptors, "_LEN must be (_MAX - _MIN + 1)", and when that's true, it
doesn't matter which way we compute the end. But of course, there are
BIOSes that don't follow this rule, and we're better off if Linux handles
those exceptions the same way as Windows.
This patch makes Linux use [_MIN to _MAX], as Windows seems to do. This
effectively reverts d558b483d5 and 03db42adfe and replaces them with
simpler code.
https://bugzilla.kernel.org/show_bug.cgi?id=14337 (round)
https://bugzilla.kernel.org/show_bug.cgi?id=15480 (truncate)
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When we move a PCI device or assign resources to a device not configured
by the BIOS, we want to avoid the BIOS region below 1MB. Note that if the
BIOS places devices below 1MB, we leave them there.
See https://bugzilla.kernel.org/show_bug.cgi?id=15744
and https://bugzilla.kernel.org/show_bug.cgi?id=15841
Tested-by: Andy Isaacson <adi@hexapodia.org>
Tested-by: Andy Bailey <bailey@akamai.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This adds support for Memory24, Memory32, and Memory32Fixed descriptors in
PCI host bridge _CRS.
I experimentally determined that Windows (2008 R2) accepts these descriptors
and treats them as windows that are forwarded to the PCI bus, e.g., if
it finds any PCI devices with BARs outside the windows, it moves them into
the windows.
I don't know whether any machines actually use these descriptors in PCI
host bridge _CRS methods, but if any exist and they're new enough that we
automatically turn on "pci=use_crs", they will work with Windows but not
with Linux.
Here are the details: https://bugzilla.kernel.org/show_bug.cgi?id=15817
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ACPI Address Space Descriptors (used in _CRS) have a Consumer/Producer
bit that is supposed to distinguish regions that are consumed directly
by a device from those that are forwarded ("produced") by a bridge.
But BIOSes have apparently not used this consistently, and Windows
seems to ignore it, so I think Linux should ignore it as well.
I can't point to any of these supposed broken BIOSes, but since we
now rely on _CRS by default, I think it's safer to ignore this bit
from the start.
Here are details of my experiments with how Windows handles it:
https://bugzilla.kernel.org/show_bug.cgi?id=15701
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The acpi_pci_root structure contains all the individual items (acpi_device,
domain, bus number) we pass to pci_acpi_scan_root(), so just pass the
single acpi_pci_root pointer directly.
This will make it easier to add _CBA support later. For _CBA, we need the
entire downstream bus range, not just the base bus number. We have that in
the acpi_pci_root structure, so passing the pointer makes it available to
the arch-specific code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Len Brown <len.brown@intel.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Yanko's GA-MA78GM-S2H (BIOS F11) reports the following resource in a PCI
host bridge _CRS:
[07] 32-Bit DWORD Address Space Resource
Min Relocatability : MinFixed
Max Relocatability : MaxFixed
Address Minimum : CFF00000 (_MIN)
Address Maximum : FEBFFFFF (_MAX)
Address Length : 3EE10000 (_LEN)
This is invalid per spec (ACPI 4.0, 6.4.3.5) because it's a fixed size,
fixed location descriptor, but _LEN != _MAX - _MIN + 1.
Based on https://bugzilla.kernel.org/show_bug.cgi?id=15480#c15, I think
Windows handles this by truncating the window so it fits between _MIN and
_MAX. I also verified this by modifying the SeaBIOS DSDT and booting
Windows 2008 R2 with qemu.
This patch makes Linux truncate the window, too, which fixes:
http://bugzilla.kernel.org/show_bug.cgi?id=15480
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Tested-by: Yanko Kaneti <yaneti@declera.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
With insert_resource_conflict(), we can learn what the actual conflict is,
so print that info for debugging purposes.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_claim_resource() already prints more detailed error messages, so these
are really redundant.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'x86-bootmem-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
early_res: Need to save the allocation name in drop_range_partial()
sparsemem: Fix compilation on PowerPC
early_res: Add free_early_partial()
x86: Fix non-bootmem compilation on PowerPC
core: Move early_res from arch/x86 to kernel/
x86: Add find_fw_memmap_area
Move round_up/down to kernel.h
x86: Make 32bit support NO_BOOTMEM
early_res: Enhance check_and_double_early_res
x86: Move back find_e820_area to e820.c
x86: Add find_early_area_size
x86: Separate early_res related code from e820.c
x86: Move bios page reserve early to head32/64.c
sparsemem: Put mem map for one node together.
sparsemem: Put usemap for one node together
x86: Make 64 bit use early_res instead of bootmem before slab
x86: Only call dma32_reserve_bootmem 64bit !CONFIG_NUMA
x86: Make early_node_mem get mem > 4 GB if possible
x86: Dynamically increase early_res array size
x86: Introduce max_early_res and early_res_count
...
Replace the #ifdef'ed OLPC-specific init functions by a conditional
x86_init function. If the function returns 0 we leave pci_arch_init,
otherwise we continue.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Andres Salomon <dilinger@collabora.co.uk>
LKML-Reference: <43F901BD926A4E43B106BF17856F0755A318CE89@orsmsx508.amr.corp.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
If we don't have any Moorestown CPU support compiled in, we don't need
the Moorestown PCI support either.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4B858E89.7040807@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
commit ff097ddd4 (x86/PCI: MMCONFIG: manage pci_mmcfg_region as a
list, not a table) introduced a nasty memory corruption when
pci_mmcfg_list is empty.
pci_mmcfg_check_end_bus_number() dereferences pci_mmcfg_list.prev even
when the list is empty. The following write hits some variable near to
pci_mmcfg_list.
Further down a similar problem exists, where cfg->list.next is
dereferenced unconditionally and a comparison with some variable near
to pci_mmcfg_list happens.
Add a check for the last element into the for_each_entry() loop and
remove all the other crappy logic which is just a leftover of the old
array based code which was replaced by the list conversion.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
While probing for the PCI fixed BAR capability in the extended PCI
configuration space we need to make sure raw_pci_ext_ops is
actually initialized.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
LKML-Reference: <43F901BD926A4E43B106BF17856F0755A321E8F7@orsmsx508.amr.corp.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The Moorestown platform only has a few devices that actually support
PCI config cycles. The rest of the devices use an in-RAM MCFG space
for the purposes of device enumeration and initialization.
There are a few uglies in the fake support, like BAR sizes that aren't
a power of two, sizing detection, and writes to the real devices, but
other than that it's pretty straightforward.
Another way to think of this is not really as PCI at all, but just a
table in RAM describing which devices are present, their capabilities
and their offsets in MMIO space. This could have been done with a
special new firmware table on this platform, but given that we do have
some real PCI devices too, simply describing things in an MCFG type
space was pretty simple.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <43F901BD926A4E43B106BF17856F07559FB80D08@orsmsx508.amr.corp.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The main benefit of using ACPI host bridge window information is that
we can do better resource allocation in systems with multiple host bridges,
e.g., http://bugzilla.kernel.org/show_bug.cgi?id=14183
Sometimes we need _CRS information even if we only have one host bridge,
e.g., https://bugs.launchpad.net/ubuntu/+source/linux/+bug/341681
Most of these systems are relatively new, so this patch turns on
"pci=use_crs" only on machines with a BIOS date of 2008 or newer.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Previously we used a table of size PCI_BUS_NUM_RESOURCES (16) for resources
forwarded to a bus by its upstream bridge. We've increased this size
several times when the table overflowed.
But there's no good limit on the number of resources because host bridges
and subtractive decode bridges can forward any number of ranges to their
secondary buses.
This patch reduces the table to only PCI_BRIDGE_RESOURCE_NUM (4) entries,
which corresponds to the number of windows a PCI-to-PCI (3) or CardBus (4)
bridge can positively decode. Any additional resources, e.g., PCI host
bridge windows or subtractively-decoded regions, are kept in a list.
I'd prefer a single list rather than this split table/list approach, but
that requires simultaneous changes to every architecture. This approach
only requires immediate changes where we set up (a) host bridges with more
than four windows and (b) subtractive-decode P2P bridges, and we can
incrementally change other architectures to use the list.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Now that we return the new resource start position, there is no
need to update "struct resource" inside the align function.
Therefore, mark the struct resource as const.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As suggested by Linus, align functions should return the start
of a resource, not void. An update of "res->start" is no longer
necessary.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Platforms like Moorestown want to override the pcibios_fixup_irqs
default function. Add it to x86_init.pci.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <43F901BD926A4E43B106BF17856F07559FB80D00@orsmsx508.amr.corp.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Moorestown wants to reuse pcibios_init_irq but needs to provide its
own implementation of pci_enable_irq. After we distangled the init we
can move the init_irq call to x86_init and remove the pci_enable_irq
!= NULL check in pcibios_init_irq. pci_enable_irq is compile time
initialized to pirq_enable_irq and the special cases which override it
(visws and acpi) set the x86_init function pointer to noop. That
allows MSRT to override pci_enable_irq and otherwise run
pcibios_init_irq unmodified.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <43F901BD926A4E43B106BF17856F07559FB80CFF@orsmsx508.amr.corp.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The PCI initialization in pci_subsys_init() is a mess. pci_numaq_init,
pci_acpi_init, pci_visws_init and pci_legacy_init are called and each
implementation checks and eventually modifies the global variable
pcibios_scanned.
x86_init functions allow us to do this more elegant. The pci.init
function pointer is preset to pci_legacy_init. numaq, acpi and visws
can modify the pointer in their early setup functions. The functions
return 0 when they did the full initialization including bus scan. A
non zero return value indicates that pci_legacy_init needs to be
called either because the selected function failed or wants the
generic bus scan in pci_legacy_init to happen (e.g. visws).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <43F901BD926A4E43B106BF17856F07559FB80CFE@orsmsx508.amr.corp.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
So make interface more consistent with early_res.
Later we can share some code with early_res.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-10-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Should be good for 32bit too.
-v3: cast res->start
-v4: according to Linus, to use %pR instead of cast
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-9-git-send-email-yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Prepare for 32bit pci root bus
-v2: hpa said we should compare with (resource_size_t)~0
-v3: according to Linus to use MAX_RESOURCE instead.
also need need to put related patches together
-v4: according to Andrew, use min in cap_resource()
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-8-git-send-email-yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Prepare to enable it for 32bit.
-v2: remove not needed cast
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-7-git-send-email-yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Found MSI amd k8 based laptops is hiding [0x70000000, 0x80000000) RAM
from e820.
enable amd one chain even for all.
-v2: use bool for found, according to Andrew
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-6-git-send-email-yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Prepare to enable 32bit intel and amd bus.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-5-git-send-email-yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
We have almost the same code for mtrr cleanup and amd_bus checkup, and
this code will also be used in replacing bootmem with early_res,
so try to move them together and reuse it from different parts.
Also rename update_range to subtract_range as that is what the
function is actually doing.
-v2: update comments as Christoph requested
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-4-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The XQUAD stuff is part of the NUMAQ architecture, so move it there.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <1265380629-3212-2-git-send-email-brgerst@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Turned out to cause trouble on single IOH machines, and is superceded by
_CRS on multi-IOH machines with production BIOSes.
Signed-off-by: Jeff Garrett <jeff@jgarrett.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
x86, irq: Check move_in_progress before freeing the vector mapping
x86: copy_from_user() should not return -EFAULT
Revert "x86: Side-step lguest problem by only building cmpxchg8b_emu for pre-Pentium"
x86/pci: Intel ioh bus num reg accessing fix
x86: Fix size for ex trampoline with 32bit
It is above 0x100 (PCI-Express extended register space), so if mmconf
is not enable, we can't access it.
[ hpa: changed the bound from 0x200 to 0x120, which is the tight
bound. ]
Reported-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1261525263-13763-3-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Remark update_res from __init to __devinit as it is called also
from __devinit functions.
This patch removes the following warning message:
WARNING: vmlinux.o(.devinit.text+0x774a): Section mismatch
in reference from the function pci_root_bus_res() to the
function .init.text:update_res()
The function __devinit pci_root_bus_res() references
a function __init update_res().
If update_res is only used by pci_root_bus_res then
annotate update_res with a matching annotation.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Aristeu Sergio <arozansk@redhat.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: linux-pci@vger.kernel.org
Cc: x86@kernel.org
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This allows us to use the BIOS SR-IOV allocations rather than assigning
our own later on.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch factors out the search for an MMCONFIG region, which was
previously implemented in both mmconfig_32 and mmconfig_64. No functional
change.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; just tidy up printks and make them more consistent
with the rest of PCI.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This is only used internally now, but eventually will be used in the
hot-remove path to remove the MMCONFIG region associated with a host bridge.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This changes pci_mmcfg_region from a table to a list, to make it easier
to add and remove MMCONFIG regions for PCI host bridge hotplug.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This replaces "typeof(pci_mmcfg_config[0])" with the actual type because
I plan to convert pci_mmcfg_config to a list, and then "pci_mmcfg_config[0]"
won't mean anything.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The virtual address is only used for x86_64, but it's so much simpler
to manage it as part of the pci_mmcfg_region that I think it's worth
wasting a pointer per MMCONFIG region on x86_32.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since pci_mmcfg_region contains the struct resource, no need to pass the
pci_mmcfg_region *and* the resource start/size.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds a resource and corresponding name to the MMCONFIG
structure. This makes allocation simpler (we can allocate the
resource and name at the same time we allocate the pci_mmcfg_region),
and gives us a way to hang onto the resource after inserting it.
This will be needed so we can release and free it when hot-removing
a host bridge.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change, but simplifies a future patch to convert the table
to a list.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This only renames the struct pci_mmcfg_region members; no functional change.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This adds a struct pci_mmcfg_region with a little more information
than the struct acpi_mcfg_allocation used previously. The acpi_mcfg
structure is defined by the spec, so we can't change it.
To begin with, struct pci_mmcfg_region is basically the same as the
ACPI MCFG version, but future patches will add more information.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This factors out the common "bus << 20" expression used when computing the
MMCONFIG address.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since all MMCONFIG regions go through pci_mmconfig_add(), we can test the
address once there. If the caller supplies an address of zero, we never
insert it in the pci_mmcfg_config[] table, so no need to test it elsewhere.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We never set pci_mmcfg_config unless we increment pci_mmcfg_config_num,
so there's no need to test both pci_mmcfg_config_num and pci_mmcfg_config.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch encapsulate pci_mmcfg_config[] updates. All alloc/free is now
done in pci_mmconfig_add() and free_all_mcfg(), so all updates to
pci_mmcfg_config[] and pci_mmcfg_config_num are in those two functions.
This replaces the previous sequence of extend_mmcfg(), fill_one_mmcfg()
with the single pci_mmconfig_add() interface. This interface is currently
static but will eventually be used in the host bridge hot-add path.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Step through the ACPI MCFG table, not pci_mmcfg_config[]. No functional
change, but simplifies future patches that encapsulate pci_mmcfg_config[].
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use a local variable, not pci_mmcfg_config_num, to count MCFG entries.
No functional change, but simplifies future changes.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Those functions are used by intel_bus.c so seperate them to another file. and
make amd_bus a bit smaller.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
commit db635adc turned -DDEBUG for x86/pci on when CONFIG_PCI_DEBUG
is set. In general, I agree with that change.
However, it exposes a bunch of very low level PCI debugging in the
early x86 path, such as:
0 reading 2 from a: ffff
1 reading 2 from a: ffff
2 reading 2 from a: ffff
3 reading 2 from a: 300
3 reading 2 from 0: 1002
3 reading 2 from 2: 515e
These statements add a lot of noise to the boot and aren't likely to
be necessary even when handling random upstream bug reports.
[In contrast, statements such as these:
pci 0000:02:04.0: found [14e4:164a] class 000200 header type 00
pci 0000:02:04.0: reg 10: [mem 0xf8000000-0xf9ffffff 64bit]
pci 0000:02:04.0: reg 30: [mem 0x00000000-0x0001ffff pref]
are indeed useful when remote debugging users' machines]
Remove the noisy printks and save electrons everywhere.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The roundup() caused a build error (undefined reference to `__udivdi3').
We're aligning to power-of-two boundaries, so it's simpler to just use
ALIGN() anyway, which avoids the division.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCI device BARs are guaranteed to start and end on at least a four-byte
(I/O) or a sixteen-byte (MMIO) boundary because they're aligned on their
size and the low BAR bits are reserved. PCI-to-PCI bridge apertures
have even larger alignment restrictions.
However, some BIOSes (e.g., HP DL360 BIOS P31) report host bridge windows
like "[io 0x0000-0x2cfe]". This is wrong because it excludes the last
port at 0x2cff: it's impossible for a downstream device to claim 0x2cfe
without also claiming 0x2cff. In fact, this BIOS configures a device
behind the bridge to "[io 0x2c00-0x2cff]", so we know the window actually
does include 0x2cff.
This patch rounds the start and end of apertures to the appropriate
boundary. I experimentally determined that Windows contains a similar
workaround; details here:
http://bugzilla.kernel.org/show_bug.cgi?id=14337
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We have occasional problems with PCI resource allocation, and sometimes
they could be avoided by paying attention to what ACPI tells us about
the host bridges. This patch doesn't change the behavior, but it prints
window information that should make debugging easier.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This makes PCI resource management messages more consistent and adds a few
new messages to aid debugging.
Whenever we assign resources to a device, update a BAR, or change a
bridge aperture, it's worth noting it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the dev_printk-like "%04x:%02x" format for printing PCI bus numbers.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Jesse accidentally applied v1 [1] of the patchset instead of v2 [2]. This
is the diff between v1 and v2.
The changes in this patch are:
- tidied vsprintf stack buffer to shrink and compute size more
accurately
- use %pR for decoding and %pr for "raw" (with type and flags) instead
of adding %pRt and %pRf
[1] http://lkml.org/lkml/2009/10/6/491
[2] http://lkml.org/lkml/2009/10/13/441
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We use dev_dbg() in arch/x86/pci, but there's no easy way to turn it
on. Add -DDEBUG when CONFIG_PCI_DEBUG=y, just like we do in drivers/pci.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The current whitelist requires a kernel change for every machine that has
MMCONFIG regions above 4GB, even if BIOS provides a correct MCFG table.
This patch expands the whitelist to include machines with a rev 1 or newer
MCFG table and a DMI_BIOS_DATE of 2010 or later. That way, we only need
kernel changes for new machines that provide incorrect MCFG tables.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Matthew Wilcox <willy@linux.intel.com>
CC: John Keller <jpk@sgi.com>
CC: Yinghai Lu <yhlu.kernel@gmail.com>
CC: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
CC: Andi Kleen <andi@firstfloor.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Thomas Schlichter reported:
> X.org uses libpciaccess which tries to mmap with write combining enabled via
> /sys/bus/pci/devices/*/resource0_wc. Currently, when PAT is not enabled, the
> kernel does fall back to uncached mmap. Then libpciaccess thinks it succeeded
> mapping with write combining enabled and does not set up suited MTRR entries.
> ;-(
Instead of silently mapping pci mmap region as UC minus in the case
of !pat_enabled and wc request, we can return error. Eric Anholt mentioned
that caller (like X) typically follows up with UC minus pci mmap request and
if there is a free mtrr slot, caller will manage adding WC mtrr.
Jesse Barnes says:
> Older versions of libpciaccess will behave better if we do it that way
> (iirc it only allocates an MTRR if the resource_wc file doesn't exist or
> fails to get mapped).
Reported-by: Thomas Schlichter <thomas.schlichter@web.de>
Signed-off-by: Thomas Schlichter <thomas.schlichter@web.de>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Instead of the PCI code needing to have code to determine the
cacheline size of each processor, use the data the cpu identification
code should have already determined during early boot.
(The vendor checks are also incomplete, and don't take into account
modern CPUs)
I've been carrying a variant of this code in Fedora for a while,
that prints debug information. There are a number of cases where we
are currently setting the PCI cacheline size to 32 bytes, when the CPU
cacheline size is 64 bytes. With this patch, we set them both the same.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Till now, CLS has been determined either by arch code or as
L1_CACHE_BYTES. Only x86 and ia64 set CLS explicitly and x86 doesn't
always get it right. On most configurations, the chance is that
firmware configures the correct value during boot.
This patch makes pci_init() determine CLS by looking at what firmware
has configured. It scans all devices and if all non-zero values
agree, the value is used. If none is configured or there is a
disagreement, pci_dfl_cache_line_size is used. arch can set the dfl
value (via PCI_CACHE_LINE_BYTES or pci_dfl_cache_line_size) or
override the actual one.
ia64, x86 and sparc64 updated to set the default cls instead of the
actual one.
While at it, declare pci_cache_line_size and pci_dfl_cache_line_size
in pci.h and drop private declarations from arch code.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Miller <davem@davemloft.net>
Acked-by: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For intel systems with multi IOH, we should read peer root resources
directly from PCI config space, and don't trust _CRS.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code
But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (75 commits)
PCI hotplug: clean up acpi_run_hpp()
PCI hotplug: acpiphp: use generic pci_configure_slot()
PCI hotplug: shpchp: use generic pci_configure_slot()
PCI hotplug: pciehp: use generic pci_configure_slot()
PCI hotplug: add pci_configure_slot()
PCI hotplug: clean up acpi_get_hp_params_from_firmware() interface
PCI hotplug: acpiphp: don't cache hotplug_params in acpiphp_bridge
PCI hotplug: acpiphp: remove superfluous _HPP/_HPX evaluation
PCI: Clear saved_state after the state has been restored
PCI PM: Return error codes from pci_pm_resume()
PCI: use dev_printk in quirk messages
PCI / PCIe portdrv: Fix pcie_portdrv_slot_reset()
PCI Hotplug: convert acpi_pci_detect_ejectable() to take an acpi_handle
PCI Hotplug: acpiphp: find bridges the easy way
PCI: pcie portdrv: remove unused variable
PCI / ACPI PM: Propagate wake-up enable for devices w/o ACPI support
ACPI PM: Replace wakeup.prepared with reference counter
PCI PM: Introduce device flag wakeup_prepared
PCI / ACPI PM: Rework some debug messages
PCI PM: Simplify PCI wake-up code
...
Fixed up conflict in arch/powerpc/kernel/pci_64.c due to OF device tree
scanning having been moved and merged for the 32- and 64-bit cases. The
'needs_freset' initialization added in 6e19314cc ("PCI/powerpc: support
PCIe fundamental reset") is now in arch/powerpc/kernel/pci_of_scan.c.
The current mp_bus_to_node array is initialized only by AMD specific
code, since AMD platforms have registers that can be used for
determining mode numbers. On new Intel platforms it's necessary to
initialize this array as well though, otherwise all PCI node numbers
will be 0, when in fact they should be -1 (indicating that I/O isn't
tied to any particular node).
So move the mp_bus_to_node code into the common PCI code, and
initialize it early with a default value of -1. This may be overridden
later by arch code (e.g. the AMD code).
With this change, PCI consistent memory and other node specific
allocations (e.g. skbuff allocs) should occur on the "current" node.
If, for performance reasons, applications want to be bound to specific
nodes, they should open their devices only after being pinned to the
CPU where they'll run, for maximum locality.
Acked-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Jesse Brandeburg <jesse.brandeburg@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There are cases where full date information is required instead of
just the year. Add month and day parsing to dmi_get_year() and rename
it to dmi_get_date().
As the original function only required '/' followed by any number of
parseable characters at the end of the string, keep that behavior to
avoid upsetting existing users.
The new function takes dates of format [mm[/dd]]/yy[yy]. Year, month
and date are checked to be in the ranges of [1-9999], [1-12] and
[1-31] respectively and any invalid or out-of-range component is
returned as zero.
The dummy implementation is updated accordingly but the return value
is updated to indicate field not found which is consistent with how
other dummy functions behave.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
First check ACPI, and if that fails, ask SFI to find the MCFG.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Linux/ACPI core files using internal.h all PREFIX "ACPI: ",
however, not all ACPI drivers use/want it -- and they
should not have to #undef PREFIX to define their own.
Add GPL commment to internal.h while we are there.
This does not change any actual console output,
asside from a whitespace fix.
Signed-off-by: Len Brown <len.brown@intel.com>
Stephen reported that his DL585 G2 needed noapic after 2.6.22 (?)
Dann bisected it down to:
commit 30a18d6c3f
Date: Tue Feb 19 03:21:20 2008 -0800
x86: multi pci root bus with different io resource range, on
64-bit
It turns out that:
1. that AMD-based systems have two HT chains.
2. BIOS doesn't allocate resources for BAR 6 of devices under 8132 etc
3. that multi-peer-root patch will try to split root resources to peer
root resources according to PCI conf of NB
4. PCI core assigns unassigned resources, but they overlap with BARs
that are used by ioapic addr of io4 and 8132.
The reason: at that point ioapic address are not inserted yet. Solution
is to insert ioapic resources into the tree a bit earlier.
Reported-by: Stephen Frost <sfrost@snowman.net>
Reported-and-Tested-by: dann frazier <dannf@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@jbarnes-g45.(none)>
This allows us to remove adjust_transparent_bridge_resources and give
x86_pci_root_bus_res_quirks a chance when _CRS is not used or not there.
Acked-by: Gary Hade <garyhade@us.ibm.com>
Tested-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Don't touch info->res_num if we are out of space.
Acked-by: Gary Hade <garyhade@us.ibm.com>
Tested-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This reverts commit 9e9f46c44e.
Quoting from the commit message:
"At this point, it seems to solve more problems than it causes, so let's
try using it by default. It's an easy revert if it ends up causing
trouble."
And guess what? The _CRS code causes trouble.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (74 commits)
PCI: make msi_free_irqs() to use msix_mask_irq() instead of open coded write
PCI: Fix the NIU MSI-X problem in a better way
PCI ASPM: remove get_root_port_link
PCI ASPM: cleanup pcie_aspm_sanity_check
PCI ASPM: remove has_switch field
PCI ASPM: cleanup calc_Lx_latency
PCI ASPM: cleanup pcie_aspm_get_cap_device
PCI ASPM: cleanup clkpm checks
PCI ASPM: cleanup __pcie_aspm_check_state_one
PCI ASPM: cleanup initialization
PCI ASPM: cleanup change input argument of aspm functions
PCI ASPM: cleanup misc in struct pcie_link_state
PCI ASPM: cleanup clkpm state in struct pcie_link_state
PCI ASPM: cleanup latency field in struct pcie_link_state
PCI ASPM: cleanup aspm state field in struct pcie_link_state
PCI ASPM: fix typo in struct pcie_link_state
PCI: drivers/pci/slot.c should depend on CONFIG_SYSFS
PCI: remove redundant __msi_set_enable()
PCI PM: consistently use type bool for wake enable variable
x86/ACPI: Correct maximum allowed _CRS returned resources and warn if exceeded
...
Instead of open-coding pci_find_parent_resource and request_resource,
just call pci_claim_resource.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Issue a warning if _CRS returns too many resource descriptors to be
accommodated by the fixed size resource array instances. If there is no
transparent bridge on the root bus "too many" is the
PCI_BUS_NUM_RESOURCES size of the resource array. Otherwise, the last 3
slots of the resource array must be excluded making the maximum
(PCI_BUS_NUM_RESOURCES - 3).
The current code:
- is silent when _CRS returns too many resource descriptors and
- incorrectly allows use of the last 3 slots of the resource array
for a root bus with a transparent bridge
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move
arch/x86/kernel/acpi/boot.c: acpi_parse_mcfg()
to
arch/x86/pci/mmconfig-shared.c: pci_parse_mcfg()
where it is used, and make it static.
Move associated globals and helper routine with it.
No functional change.
This code move is in preparation for SFI support,
which will allow the PCI code to find the MCFG table
on systems which do not support ACPI.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
At this point, it seems to solve more problems than it causes, so let's try using it by default. It's an easy revert if it ends up causing trouble.
Reviewed-by: Yinghai Lu <yhlu.kernel@gmail.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (76 commits)
x86, apic: Fix dummy apic read operation together with broken MP handling
x86, apic: Restore irqs on fail paths
x86: Print real IOAPIC version for x86-64
x86: enable_update_mptable should be a macro
sparseirq: Allow early irq_desc allocation
x86, io-apic: Don't mark pin_programmed early
x86, irq: don't call mp_config_acpi_gsi() if update_mptable is not enabled
x86, irq: update_mptable needs pci_routeirq
x86: don't call read_apic_id if !cpu_has_apic
x86, apic: introduce io_apic_irq_attr
x86/pci: add 4 more return parameters to IO_APIC_get_PCI_irq_vector(), fix
x86: read apic ID in the !acpi_lapic case
x86: apic: Fixmap apic address even if apic disabled
x86: display extended apic registers with print_local_APIC and cpu_debug code
x86: read apic ID in the !acpi_lapic case
x86: clean up and fix setup_clear/force_cpu_cap handling
x86: apic: Check rev 3 fadt correctly for physical_apic bit
x86/pci: update pirq_enable_irq() to setup io apic routing
x86/acpi: move setup io apic routing out of CONFIG_ACPI scope
x86/pci: add 4 more return parameters to IO_APIC_get_PCI_irq_vector()
...
Pascal reported and bisected a commit:
| x86/PCI: don't call e820_all_mapped with -1 in the mmconfig case
which broke one system system.
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255
PCI: MCFG area at f0000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG for extended config space
it didn't have
PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 63
anymore, and try to use 0xf000000 - 0xffffffff for mmconfig
For 32bit, mcfg_res->end could be 32bit only (if 64 resources aren't used)
So use end - 1 to pass the value in mcfg->end to avoid overflow.
We don't need to worry about the e820 path, they are always 64 bit.
Reported-by: Pascal Terjan <pterjan@mandriva.com>
Bisected-by: Pascal Terjan <pterjan@mandriva.com>
Tested-by: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
according to Ingo, io_apic irq-setup related functions have too many
parameters with a repetitive signature.
So reduce related funcs to get less params by passing a pointer
to a newly defined io_apic_irq_attr structure.
v2: io_apic_irq ==> irq_attr
triggering ==> trigger
v3: add set_io_apic_irq_attr
[ Impact: cleanup ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A08ACD3.2070401@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge reason: both topics modify the APIC code but were able to do it in
parallel so far. An upcoming patch generates a conflict so
merge them to avoid the conflict.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
So we can set io apic routing only when enabling the device irq.
This is advantageous for IRQ descriptor allocation affinity: if we set up
the IO-APIC entry later, we have a chance to allocate the IRQ descriptor
later and know which device it is on and can set affinity accordingly.
[ Impact: standardize/enhance irq-enabling sequence for mptable irqs ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A01C46E.8000501@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To prepare those params for pcibios_irq_enable() to call setup_io_apic_routing().
[ Impact: extend function call API to prepare for new functionality ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A01C406.2040303@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It will be overwriten later if _CRS is used, so don't bother to set it.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Rename set_pci_bus_resources_arch_default to x86_pci_root_bus_res_quirks, move
the weak version from common.c to i386.c, and before calling, make sure it's a
root bus.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 30a18d6c3f introduced a new
function to set the PCI bus resources. Unfortunately, neither the
author, nor the committers seemed to know that we already have somewhere
to do that -- pcibios_fixup_bus(). This patch moves the hook (used only
by the K8 code) into x86-specific code where it should have been in the
first place.
Cc: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci mmap code was doing memtype reserve for a while now. Recently we
added memtype tracking in remap_pfn_range, and pci code indirectly calls
remap_pfn_range. So, we don't need seperate tracking in pci code
anymore. Which means a patch that removes ~50 lines of code :-).
Also, recently we found out that the pci tracking is not working as we expect
it to work in some cases. Specifically, userlevel X mmap of pci, with some
recent version of X, is having a problem with vm_page_prot getting reset.
The pci tracking uses vm_page_prot to pass on the protection type from parent
to child during fork.
a) Parent does a pci mmap
b) We look at PAT and get either UC_MINUS or WC mapping for parent
c) Store that mapping type in vma vm_page_prot for future use
d) This thread does a fork
e) Fork results in mmap_ops ->open for the child process
f) We get the vm_page_prot from vma and reserve that type for the child process
But, between c) and e) above, the vma vm_page_prot is getting reset to zero.
This results in PAT reserve failing at the time of fork as in here.
http://marc.info/?l=linux-kernel&m=123858163103240&w=2
This cleanup makes the above problem go away as we do not depend on
vm_page_prot in our PAT code anymore.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (88 commits)
PCI: fix HT MSI mapping fix
PCI: don't enable too much HT MSI mapping
x86/PCI: make pci=lastbus=255 work when acpi is on
PCI: save and restore PCIe 2.0 registers
PCI: update fakephp for bus_id removal
PCI: fix kernel oops on bridge removal
PCI: fix conflict between SR-IOV and config space sizing
powerpc/PCI: include pci.h in powerpc MSI implementation
PCI Hotplug: schedule fakephp for feature removal
PCI Hotplug: rename legacy_fakephp to fakephp
PCI Hotplug: restore fakephp interface with complete reimplementation
PCI: Introduce /sys/bus/pci/devices/.../rescan
PCI: Introduce /sys/bus/pci/devices/.../remove
PCI: Introduce /sys/bus/pci/rescan
PCI: Introduce pci_rescan_bus()
PCI: do not enable bridges more than once
PCI: do not initialize bridges more than once
PCI: always scan child buses
PCI: pci_scan_slot() returns newly found devices
PCI: don't scan existing devices
...
Fix trivial append-only conflict in Documentation/feature-removal-schedule.txt
Impact: scan more peer root buses even acpi is used
Move pci_bios_fixup_peer_bridges out of pci_legacy_init and into
pci_subsys_init. This allows pci_bios_fixup_peer_bridges to be called
even pci_apci_init is driving PCI initialization.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
While looking at the issue in the thread:
http://marc.info/?l=dri-devel&m=123606627824556&w=2
noticed a bug in pci PAT code and memory type setting.
PCI mmap code did not set the proper protection in vma, when it
inherited protection in reserve_memtype. This bug only affects
the case where there exists a WC mapping before X does an mmap
with /proc or /sys pci interface. This will cause X userlevel
mmap from /proc or /sysfs to fail on fork.
Reported-by: Kevin Winchester <kjwinchester@gmail.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dave Airlie <airlied@redhat.com>
Cc: <stable@kernel.org>
LKML-Reference: <20090323190720.GA16831@linux-os.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix mmconfig detection to not assume a single mmconfig space in the
northbridge, paving the way for AMD fam10h + mcp55 CPUs. On those, the
MSR has some range, but the mcp55 pci config will have another one.
Also helps the mcp55 + io55 case, where every one will have one range.
If it is mcp55, exclude the range that is used by CPU MSR, in other
words , if the CPU claims busses 0-255, the range in mcp55 is dropped,
because CPU HW will not route those ranges to mcp55 mmconfig to handle
it.
Signed-off-by: Yinghai Lu <yinghai.lu@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Detect and enable memory-mapped PCI configuration space on the nVidia
MCP55 southbridge. Tested against 2.6.27.4 on an Arista Networks
development board with one MCP55, Coreboot firmware, no ACPI.
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Many host bridges support a 4k config space, so check them directy
instead of using quirks to add them.
We only need to do this extra check for host bridges at this point,
because only host bridges are known to have extended address space
without also having a PCI-X/PCI-E caps. Other devices with this
property could be done with quirks (if there are any).
As a bonus, we can remove the quirks for AMD host bridges with family
10h and 11h since they're not needed any more.
With this patch, we can get correct pci cfg size of new Intel CPUs/IOHs
with host bridges.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use %02x:%02x.%d rather than %02x:%02x:%02x so PCI addresses
look the same as in other parts of the kernel.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The early "dump PCI config space" code skips many multi-function
devices. This patch fixes that, so it dumps all devices in PCI
domain 0.
We should not skip the rest of the functions if CLASS_REVISION is
0xffffffff. Often multi-function devices have gaps in the function ID
space, e.g., 1c.0 and 1c.2 exist but 1c.1 doesn't. The CLASS_REVISION
of the non-existent 1c.1 function will appear to be 0xffffffff.
We should only look at the HEADER_TYPE of function zero. Often the
"multi-function" is set in function zero, but not in other functions.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Impact: debuggability and micro-optimization
Putting whatever is possible into the (final) .rodata section increases
the likelihood of catching memory corruption bugs early, and reduces
false cache line sharing.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <49B909A5.76E4.0078.0@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We are getting rid of subarchitecture support - move the hook files
to asm/. (These are now stale and should be replaced with more explicit
runtime mechanisms - but the transition is simpler this way.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move all the NUMAQ subarch definitions into numaq.c. With this it
ceases to depend on build-time subarch features.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Move the new memtype old memtype allowed check to header so that is can be
shared by other users. Subsequent patch uses this in pat.c in remap_pfn_range()
code path. No functionality change in this patch.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
pcibios_enable_device() and pcibios_disable_device() don't handle
IRQs for devices that have MSI enabled and it should treat the
devices with MSI-X enabled in the same way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since pci_bus has a struct device, use dev_printk directly instead
of faking it by hand.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Keep "pin" encoded as it is in the "Interrupt Pin" value in PCI config
space, i.e., 0=device doesn't use interrupts, 1=INTA, ..., 4=INTD.
This makes the bridge INTx swizzle match other architectures.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: hpa@zytor.com
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch makes pci_get_interrupt_pin() return values encoded
the same way as the "Interrupt Pin" value in PCI config space,
i.e., 1=INTA, ..., 4=INTD.
pirq_bios_set() is the only in-tree caller of pci_get_interrupt_pin()
and pci_get_interrupt_pin() is not exported.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: hpa@zytor.com
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Early type 1 accesses can cause problems on some platforms, and
pci=noearly is supposed to prevent them from occurring. However, early
mcfg probing code uses type 1 and isn't protected by a check for
noearly. This patch fixes that problem.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change PCI bus locality messages so they have a bit more context
and look like the rest of PCI, e.g.,
- bus 01 -> node 0
- bus 04 -> node 0
+ pci 0000:01: bus on NUMA node 0
+ pci 0000:04: bus on NUMA node 0
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These are easy to trigger (more or less harmlessly) with multiple video
cards, since the ROM BAR will typically not be given any space by the
BIOS bridge setup. No reason to punish quiet boot for this.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The _OSC capability OSC_EXT_PCI_CONFIG_SUPPORT is set when the root
bridge is added with pci_acpi_osc_support() if we can access PCI
extended config space.
This adds the function pci_ext_cfg_avail which returns true if we can
access PCI extended config space (offset greater than 0xff). It
currently only returns false if arch=x86 and raw_pci_ext_ops is not set
(which might happen if pci=nommcfg is set on the kernel command-line).
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Impact: cleanup
Now that arch/x86/pci/pci.h is used in a number of other places as well,
move the lowlevel x86 pci definitions into the architecture include files.
(not to be confused with the existing arch/x86/include/asm/pci.h file,
which provides public details about x86 PCI)
Tested on: X86_32_UP, X86_32_SMP and X86_64_SMP
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: extend allowed configuration space access on 11h CPUs from 256 to 4K
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: Changes reboot behavior.
If port CF9 seems to be safe to touch, attempt it before trying the
keyboard controller. Port CF9 is not available on all chipsets (a
significant but decreasing number of modern chipsets don't implement
it), but port CF9 itself should in general be safe to poke (no ill
effects if unimplemented) on any system which has PCI Configuration
Method #1 or #2, as it falls inside the PCI configuration port range
in both cases. No chipset without PCI is known to have port CF9,
either, although an explicit "pci=bios" would mean we miss this and
therefore don't use port CF9. An explicit "reboot=pci" can be used to
force the use of port CF9.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch updates the Intel Ibex Peak (PCH) LPC and SMBus Controller
DeviceIDs.
The LPC Controller ID is set by Firmware within the range of
0x3b00-3b1f. This range is included in pci_ids.h using min and max
values, and irq.c now has code to handle the range (in lieu of 32
additions to a SWITCH statement).
The SMBus Controller ID is a fixed-value and will not change.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use "[%04x:%04x]" for PCI vendor/device IDs to follow the format
used by lspci(8).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Prevent the HPET resources from appearing in PCI device 14.0 which
confuses the PCI resource engine.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
this one replaces:
| commit a2bd7274b4
| Author: Yinghai Lu <yhlu.kernel@gmail.com>
| Date: Mon Aug 25 00:56:08 2008 -0700
|
| x86: fix HPET regression in 2.6.26 versus 2.6.25, check hpet against BAR, v3
v2: insert e820 reserve resources before pnp_system_init
v3: fix merging problem in tip/x86/core
v4: address Linus's review about comments and condition in _late()
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so could let BAR res register at first, or even pnp.
v2: insert e820 reserve resources before pnp_system_init
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Breaking lines due to some imaginary problem with a long line length is
often stupid and wrong, but never more so when it splits a string that
is printed out into multiple lines. This really ended up making it much
harder to find where some error strings were printed out, because a
simple 'grep' didn't work.
I'm sure there is tons more of this particular idiocy hiding in other
places, but this particular case hit me once more last week. So fix it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit a2bd7274b4.
It wasn't really right to begin with (there's a better fix for the
problem with e820 reservations clashing with PCI BAR's pending), but it
also actually causes more regressions, so it should be reverted even
before the better fix is finalized.
Rafael reports that this commit broke AHCI detection, and thus causes
the kernel to not boot on his quad core test box.
Reported-and-bisected-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: David Witbrodt <dawitbro@sbcglobal.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Witbrodt tracked down (and bisected) a hpet bootup hang on his
system to the following problem: a BIOS bug made the hpet device
visible as a generic PCI device. If e820 reserved entries happen to
be registered first in the resource tree [which v2.6.26 started doing],
then the PCI code will reallocate that device's BAR to some other
address - breaking timer IRQs and hanging the system.
( Normally hpet devices are hidden by the BIOS from the OS's PCI
discovery via chipset magic. Sometimes the hpet is not a PCI device
at all. )
Solve this fundamental fragility by making non-PCI platform drivers
insert resources into the resource tree even if it overlaps the e820
reserved entry, to keep the resource manager from updating the BAR.
Also do these checks for the ioapic and mmconfig addresses, and emit
a warning if this happens.
Bisected-by: David Witbrodt <dawitbro@sbcglobal.net>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Tested-by: David Witbrodt <dawitbro@sbcglobal.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jan Beulich wrote:
> Even worse - this would even try to access the MSR on non-AMD CPUs
> (currently probably prevented just by the fact that only AMD ones use
> family values of 0x10 or higher).
This patch adds cpu vendor check to the postcore_initcalls.
Reported-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: add acpi_find_root_bridge_handle
PCI: acpi_pcihp: run _OSC on a root bridge
x86/PCI: irq and pci_ids patch for Intel Ibex Peak PCHs
x86/PCI: allow scanning of 255 PCI busses
x86, pci: detect end_bus_number according to acpi/e820 reserved, v2
pci: debug extra pci bus resources
pci: debug extra pci resources range
There's so much broken mmconfig hardware/bios'es out there,
that classing this as an error seems a little extreme.
Lower its priority to KERN_INFO so that it isn't so noisy
when booting with 'quiet'
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix an old off by one error in the legacy PCI bus check. 0xff
is a valid bus.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Convert printks to use dev_printk().
I converted DBG() to dev_dbg(). This DBG() is from arch/x86/pci/pci.h and
requires source-code modification to enable, so dev_dbg() seems roughly
equivalent.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use generic_access_phys as the access_process_vm access function for
/dev/mem mappings. This makes it possible to debug the X server.
[akpm@linux-foundation.org: repair all the architectures which broke]
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Benjamin Herrensmidt <benh@kernel.crashing.org>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dump all the PIC, local APIC and I/O APIC information at the
fs_initcall() level, which is after ACPI (if used) has initialised PCI
information, making the point of invocation consistent across MP-table and
ACPI platforms. Remove explicit calls to print_IO_APIC() from elsewhere.
Make the interface of all the functions involved consistent between 32-bit
and 64-bit versions and make them all static by default by the means of a
New-and-Improved(TM) __apicdebuginit() macro.
Note that like print_IO_APIC() all these only output anything if
"apic=debug" has been passed to the kernel through the command line.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are a couple of places where (P)Dprintk is used which is an old
compile time enabled printk wrapper. Convert it to the generic
pr_debug().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Jack Howarth reported that 2.6.26-rc9-git9 doesn't boot on MacBookPro2.
the reason is a faulty BIOS update that reportes faulty resources.
Nevertheless it's possible for Linux to be more resolent about this
situation (and similar situations) and work around this bug, by
cross-checking the mmconf range against the e820 table and ACPI resources.
Change the mconf bus range from [0,0xff] to to [0, 0x3f]
to match range [0xf0000000, 0xf4000000) in e820 tables.
[ v2, yhlu.kernel@gmail.com:
x86, pci: detect end_bus_number according to acpi/e820 reserved - fix ]
Reported-by: Jack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: jbarnes@virtuousgeek.org
Cc: Jack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is against linux-2.6-tip, branch pci-ioapic-boot-irq-quirks.
From: Stefan Assmann <sassmann@suse.de>
Subject: Introduce config option for pci reroute quirks
The config option X86_REROUTE_FOR_BROKEN_BOOT_IRQS is introduced to
enable (or disable) the redirection of the interrupt handler to the boot
interrupt line by default. Depending on the existence of interrupt
masking / threaded interrupt handling in the kernel (vanilla, rt, ...)
and the maturity of the rerouting patch, users can enable or disable the
redirection by default.
This means that the reroute quirk can be applied to any kernel without
changing it.
Interrupt sharing could be increased if this option is enabled. However this
option is vital for threaded interrupt handling, as done by the RT kernel.
It should simplify the consolidation with the RT kernel.
The option can be overridden by either pci=ioapicreroute or
pci=noioapicreroute.
Signed-off-by: Stefan Assmann <sassmann@suse.de>
Signed-off-by: Olaf Dabrunz <od@suse.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jon Masters <jonathan@jonmasters.org>
Cc: Ihno Krumreich <ihno@suse.de>
Cc: Sven Dietrich <sdietrich@suse.de>
Cc: Daniel Gollub <dgollub@suse.de>
Cc: Felix Foerster <ffoerster@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
Revert "x86/PCI: ACPI based PCI gap calculation"
PCI: remove unnecessary volatile in PCIe hotplug struct controller
x86/PCI: ACPI based PCI gap calculation
PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
PCI PM: Fix pci_prepare_to_sleep
x86/PCI: Fix PCI config space for domains > 0
Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
PCI: Simplify PCI device PM code
PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
PCI ACPI: Rework PCI handling of wake-up
ACPI: Introduce new device wakeup flag 'prepared'
ACPI: Introduce acpi_device_sleep_wake function
PCI: rework pci_set_power_state function to call platform first
PCI: Introduce platform_pci_power_manageable function
ACPI: Introduce acpi_bus_power_manageable function
PCI: make pci_name use dev_name
PCI: handle pci_name() being const
PCI: add stub for pci_set_consistent_dma_mask()
PCI: remove unused arch pcibios_update_resource() functions
PCI: fix pci_setup_device()'s sprinting into a const buffer
...
Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
Using ACPI to find free address space allows us to find a gap for the
unallocated PCI resources or MMIO resources for hotplug devices within
the BIOS allowed PCI regions.
It works by evaluating the _CRS object under PCI0 looking for producer
resources. Then searches the e820 memory space for a gap within these
producer resources.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
fix merge fallout:
arch/x86/pci/amd_bus.c: In function ‘enable_pci_io_ecs':
arch/x86/pci/amd_bus.c:581: error: too many arguments to function ‘on_each_cpu'
Signed-off-by: Ingo Molnar <mingo@elte.hu>
John Keller reports that PCI config space access is broken on machines
with more than one domain. conf1 accesses only work for domain 0, so make sure
we check the domain number in the raw routines before trying conf1.
Reported-by: John Keller <jpk@sgi.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
tighten the boundary checks around max_low_pfn_mapped - dont overmap
nor undermap into holes.
also print out tseg for AMD cpus, for diagnostic purposes.
(this is an SMM area, and we split up any big mappings around that area)
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I don't know, if this new code boots, but at least it
compiles. Someone should really test it.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Cc: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when more than 4g memory is installed, don't map the big hole below 4g.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Patch d49c4288 (tip/x86/mpparse) introduced some changes in calling
subsys_init calls if CONFIG_X86_NUMAQ option is set. This patch
updates subsystem initalization according to this changes.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Cc: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
move the include/asm-x86/mach-visws/ VISWS specific hardware
details include files into include/asm-x86/visws, to be used from
generic code.
No code changed.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
first step: make the VISWS subarch boot on a regular PC.
We take various shortcuts for that. We copy the generic arch setup file over
into the VISWS setup file.
This is the only step that is not expected to boot on a real VISWS.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
So far subsys_initcalls has been executed in this order depending on
the object order in the Makefile:
arch/x86/pci/visws.c:subsys_initcall(pcibios_init);
arch/x86/pci/numa.c:subsys_initcall(pci_numa_init);
arch/x86/pci/acpi.c:subsys_initcall(pci_acpi_init);
arch/x86/pci/legacy.c:subsys_initcall(pci_legacy_init);
arch/x86/pci/irq.c:subsys_initcall(pcibios_irq_init);
arch/x86/pci/common.c:subsys_initcall(pcibios_init);
This patch removes the ordering dependency. There is now only one
subsys_initcall function that contains subsystem initialization code
with a defined order.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This should be safe since mmconfig*.o and init.o do not contain
*initcalls with the same level as in other files.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce pci=ioapicreroute kernel cmdline option to enable rerouting of boot
interrupts to the primary io-apic.
Signed-off-by: Stefan Assmann <sassmann@suse.de>
Signed-off-by: Olaf Dabrunz <od@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
also make bus_numa work even if ACPI_NUMA is not defined.
don't call pxm_to_node again, and use node directly.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
a numa system (with multi HT chains) may return node without ram. Aka it
is not online. Try to get an online node, otherwise return -1.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
"Form follows function". Code is now where it belongs to.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The name fits better since this is code not only for K8.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit a167607255. It duplicates
the change from 8d64c781f0 and only one should be
applied, otherwise some of the Dell quirks are lost.
Thanks to Tony Camuso for catching this.
Acked-by: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
BTW, what does pat_wc_enabled stand for? Does it mean
"write-combining"?
Currently it is used to globally switch on or off PAT support.
Thus I renamed it to pat_enabled.
I think this increases readability (and hope that I didn't miss
something).
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Allows us to dump PCI space before any kernel changes have been made.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Contention for scarce PCI memory resources has been growing
due to an increasing number of PCI slots in large multi-node
systems. The kernel currently attempts by default to
allocate memory for all PCI expansion ROMs so there has
also been an increasing number of PCI memory allocation
failures seen on these systems. This occurs because the
BIOS either (1) provides insufficient PCI memory resource
for all the expansion ROMs or (2) provides adequate PCI
memory resource for expansion ROMs but provides the
space in kernel unexpected BIOS assigned P2P non-prefetch
windows.
The resulting PCI memory allocation failures may be benign
when related to memory requests for expansion ROMs themselves
but in some cases they can occur when attempting to allocate
space for more critical BARs. This can happen when a successful
expansion ROM allocation request consumes memory resource
that was intended for a non-ROM BAR. We have seen this
happen during PCI hotplug of an adapter that contains a
P2P bridge where successful memory allocation for an
expansion ROM BAR on device behind the bridge consumed
memory that was intended for a non-ROM BAR on the P2P bridge.
In all cases the allocation failure messages can be very
confusing for users.
This patch provides a new 'pci=norom' kernel boot parameter
that can be used to disable the default PCI expansion ROM memory
resource allocation. This provides a way to avoid the above
described issues on systems that do not contain PCI devices
for which drivers or user-level applications depend on the
default PCI expansion ROM memory resource allocation behavior.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
... so it could fall back to normal numa and we'd reduce the impact of the
NUMAQ subarch.
NUMAQ depends on GENERICARCH
also decouple genericarch numa from acpi.
also make it fall back to bigsmp if apicid > 8.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This BIOS claims the VIA 8237 south bridge to be compatible with VIA 586,
which it is not.
Without this patch, I get the following warning while booting,
among others,
| PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0
| ------------[ cut here ]------------
| WARNING: at arch/x86/pci/irq.c:265 pirq_via586_get+0x4a/0x60()
| Modules linked in:
| Pid: 1, comm: swapper Not tainted 2.6.26-rc4-00015-g1ec7d99 #1
| [<c0119fd4>] warn_on_slowpath+0x54/0x70
| [<c02246e0>] ? vt_console_print+0x210/0x2b0
| [<c02244d0>] ? vt_console_print+0x0/0x2b0
| [<c011a413>] ? __call_console_drivers+0x43/0x60
| [<c011a482>] ? _call_console_drivers+0x52/0x80
| [<c011aa89>] ? release_console_sem+0x1c9/0x200
| [<c0291d21>] ? raw_pci_read+0x41/0x70
| [<c0291e8f>] ? pci_read+0x2f/0x40
| [<c029151a>] pirq_via586_get+0x4a/0x60
| [<c02914d0>] ? pirq_via586_get+0x0/0x60
| [<c029178d>] pcibios_lookup_irq+0x15d/0x430
| [<c03b895a>] pcibios_irq_init+0x17a/0x3e0
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c03a6763>] kernel_init+0x73/0x250
| [<c03b87e0>] ? pcibios_irq_init+0x0/0x3e0
| [<c0114d00>] ? schedule_tail+0x10/0x40
| [<c0102dee>] ? ret_from_fork+0x6/0x1c
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c010324b>] kernel_thread_helper+0x7/0x1c
| =======================
| ---[ end trace 4eaa2a86a8e2da22 ]---
and IRQ trouble later,
| irq 10: nobody cared (try booting with the "irqpoll" option)
Now that's an VIA 8237 chip, so pirq_via586_get shouldn't be called
at all; adding this workaround to via_router_probe() fixes the
problem for me.
Amazingly I have a 2.6.23.8 kernel that somehow works fine ... I'll
never understand why.
Signed-off-by: Bertram Felgenhauer <int-e@gmx.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Previously, one would have to specifically choose CONFIG_OLPC and
CONFIG_PCI_GOOLPC in order to enable PCI_OLPC. That doesn't really work
for distro kernels, so this patch allows one to choose CONFIG_OLPC and
CONFIG_PCI_GOANY in order to build in OLPC support in a generic kernel (as
requested by Robert Millan).
This also moves GOOLPC before GOANY in the menuconfig list.
Finally, make pci_access_init return early if we detect OLPC hardware.
There's no need to continue probing stuff, and pci_pcbios_init
specifically trashes our settings (we didn't run into that before because
PCI_GOANY wasn't supported).
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch implements PCI extended configuration space access for
AMD's Barcelona CPUs. It extends the method using CF8/CFC IO
addresses. An x86 capability bit has been introduced that is set for
CPUs supporting PCI extended config space accesses.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This BIOS claims the VIA 8237 south bridge to be compatible with VIA 586,
which it is not.
Without this patch, I get the following warning while booting,
among others,
| PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0
| ------------[ cut here ]------------
| WARNING: at arch/x86/pci/irq.c:265 pirq_via586_get+0x4a/0x60()
| Modules linked in:
| Pid: 1, comm: swapper Not tainted 2.6.26-rc4-00015-g1ec7d99 #1
| [<c0119fd4>] warn_on_slowpath+0x54/0x70
| [<c02246e0>] ? vt_console_print+0x210/0x2b0
| [<c02244d0>] ? vt_console_print+0x0/0x2b0
| [<c011a413>] ? __call_console_drivers+0x43/0x60
| [<c011a482>] ? _call_console_drivers+0x52/0x80
| [<c011aa89>] ? release_console_sem+0x1c9/0x200
| [<c0291d21>] ? raw_pci_read+0x41/0x70
| [<c0291e8f>] ? pci_read+0x2f/0x40
| [<c029151a>] pirq_via586_get+0x4a/0x60
| [<c02914d0>] ? pirq_via586_get+0x0/0x60
| [<c029178d>] pcibios_lookup_irq+0x15d/0x430
| [<c03b895a>] pcibios_irq_init+0x17a/0x3e0
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c03a6763>] kernel_init+0x73/0x250
| [<c03b87e0>] ? pcibios_irq_init+0x0/0x3e0
| [<c0114d00>] ? schedule_tail+0x10/0x40
| [<c0102dee>] ? ret_from_fork+0x6/0x1c
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c010324b>] kernel_thread_helper+0x7/0x1c
| =======================
| ---[ end trace 4eaa2a86a8e2da22 ]---
and IRQ trouble later,
| irq 10: nobody cared (try booting with the "irqpoll" option)
Now that's an VIA 8237 chip, so pirq_via586_get shouldn't be called
at all; adding this workaround to via_router_probe() fixes the
problem for me.
Amazingly I have a 2.6.23.8 kernel that somehow works fine ... I'll
never understand why.
Signed-off-by: Bertram Felgenhauer <int-e@gmx.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
there is a typo in the mask value, need to remove that extra 0,
to avoid 4bit clearing.
Signed-off-by: Yinghal Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Greetings.
There is a code flaw in the bfsort whitelist, where there are redundant
entries for the same two HP systems, DL385 G2 and DL585 G2. This patch
replaces those redundant entries with the correct ones. The correct
entries are for large-volume systems, the DL360 and DL380.
-----------------------------------------------------------------------
commit ec69f0374c3b0ad7ea991b0e9ac00377acfe5b1a
Author: Tony Camuso <tony.camuso@hp.com>
Date: Wed May 14 07:09:28 2008 -0400
Replace Redundant Whitelist Entries with the Correct Ones
The ProLiant DL585 G2 and the DL585 G2 are entered reundantly
in the dmi_system_id table. What should have been there are the
DL360 and DL380. This patch simply replaces the redundant
entries with the correct entries.
arch/x86/pci/common.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
Signed-off-by: Tony Camuso <tony.camuso@hp.com>
Signed-off-by: Pat Schoeller <patrick.schoeller@hp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Replace Redundant Whitelist Entries with the Correct Ones
The ProLiant DL585 G2 and the DL585 G2 are entered reundantly in the
dmi_system_id table. What should have been there are the DL360 and DL380. This
patch simply replaces the redundant entries with the correct entries.
Signed-off-by: Tony Camuso <tony.camuso@hp.com>
Signed-off-by: Pat Schoeller <patrick.schoeller@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some versions of X used the mprotect workaround to change caching type from UC
to WB, so that it can then use mtrr to program WC for that region [1]. Change
the mmap of pci space through /sys or /proc interfaces from UC to UC_MINUS.
With this change, X will not need to use mprotect workaround to get WC type
since the MTRR mapping type will be honored.
The bug in mprotect that clobbers PAT bits is fixed in a follow on patch. So,
this X workaround will stop working as well.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: rdc: leds build/config fix
x86: sysfs cpu?/topology is empty in 2.6.25 (32-bit Intel system)
x86: revert commit 709f744 ("x86: bitops asm constraint fixes")
x86: restrict keyboard io ports reservation to make ipmi driver work
x86: fix fpu restore from sig return
x86: remove spew print out about bus to node mapping
x86: revert printk format warning change which is for linux-next
x86: cleanup PAT cpu validation
x86: geode: define geode_has_vsa2() even if CONFIG_MGEODE_LX is not set
x86: GEODE: cache results from geode_has_vsa2() and uninline
x86: revert geode config dependency
Jeff Garzik pointed out that this printout is not needed.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This reverts commit 9f8daccaa0, which was
reported to break X startup (xf86-video-ati-6.8.0). See
http://bugs.freedesktop.org/show_bug.cgi?id=15523
for details.
Reported-by: Laurence Withers <l@lwithers.me.uk>
Cc: Gary Hade <garyhade@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: "Jun'ichi Nomura" <j-nomura@ce.jp.nec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86 PCI: call dmi_check_pciprobe()
x86/pci: add pci=skip_isa_align command lines.
x86/pci: remove flag in pci_cfg_space_size_ext
x86: fix section mismatch in pci_scan_bus
this change:
| commit 08f1c192c3
| Author: Muli Ben-Yehuda <muli@il.ibm.com>
| Date: Sun Jul 22 00:23:39 2007 +0300
|
| x86-64: introduce struct pci_sysdata to facilitate sharing of ->sysdata
|
| This patch introduces struct pci_sysdata to x86 and x86-64, and
| converts the existing two users (NUMA, Calgary) to use it.
|
| This lays the groundwork for having other users of sysdata, such as
| the PCI domains work.
|
| The Calgary bits are tested, the NUMA bits just look ok.
replaces pcibios_scan_root with pci_scan_bus_parented...
but in pcibios_scan_root we have a DMI check:
dmi_check_system(pciprobe_dmi_table);
when when have several peer root buses this could be called multiple
times (which is bad), so move that call to pci_access_init().
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
so we don't align the io port start address for pci cards.
also move out dmi check out acpi.c, because it has nothing to do with acpi.
it could spare some calling when we have several peer root buses.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
arch/x86/pci/Makefile_32 has a nasty detail. VISWS and NUMAQ build
override the generic pci-y rules. This needs a proper cleanup, but
that needs more thoughts. Undo
commit 895d30935e
x86: numaq fix
do not override the existing pci-y rule when adding visws or
numaq rules.
There is also a stupid init function ordering problem vs. acpi.o
Add comments to the Makefile to avoid tripping over this again.
Remove the srat stub code in discontig_32.c to allow a proper NUMAQ
build.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use UC_MINUS for ioremap(), ioremap_nocache() instead of strong UC.
Once all the X drivers move to ioremap_wc(), we can go back to strong
UC semantics for ioremap() and ioremap_nocache().
To avoid attribute aliasing issues, pci_mmap_page_range() will also
use UC_MINUS for default non write-combining mapping request.
Next steps:
a) change all the video drivers using ioremap() or ioremap_nocache()
and adding WC MTTR using mttr_add() to ioremap_wc()
b) for strict usage, we can go back to strong uc semantics
for ioremap() and ioremap_nocache() after some grace period for
completing step-a.
c) user level X server needs to use the appropriate method for setting
up WC mapping (like using resourceX_wc sysfs file instead of
adding MTRR for WC and using /dev/mem or resourceX under /sys)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
so let pci_cfg_space_size call it directly without flag.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix following section mismatch warning:
WARNING: vmlinux.o(.text+0x275616): Section mismatch in reference from the function pci_scan_bus() to the function .devinit.text:pci_scan_bus_parented()
The warning was seen with a CONFIG_DEBUG_SECTION_MISMATCH=y build.
The inline function pci_scan_bus refer to functions annotated
__devinit - so annotate it __devinit too.
This revealed a few x86 specific functions that were only
used from __init or __devinit context.
So annotate these __devinit and the warning was killed.
The added include in pci.h was not strictly required but
added to avoid being dependent on indirect includes.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-pci:
x86: add pci=check_enable_amd_mmconf and dmi check
x86: work around io allocation overlap of HT links
acpi: get boot_cpu_id as early for k8_scan_nodes
x86_64: don't need set default res if only have one root bus
x86: double check the multi root bus with fam10h mmconf
x86: multi pci root bus with different io resource range, on 64-bit
x86: use bus conf in NB conf fun1 to get bus range on, on 64-bit
x86: get mp_bus_to_node early
x86 pci: remove checking type for mmconfig probe
x86: remove unneeded check in mmconf reject
driver core: try parent numa_node at first before using default
x86: seperate mmconf for fam10h out from setup_64.c
x86: if acpi=off, force setting the mmconf for fam10h
x86_64: check MSR to get MMCONFIG for AMD Family 10h
x86_64: check and enable MMCONFIG for AMD Family 10h
x86_64: set cfg_size for AMD Family 10h in case MMCONFIG
x86: mmconf enable mcfg early
x86: clear pci_mmcfg_virt when mmcfg get rejected
x86: validate against acpi motherboard resources
Fixed up fairly trivial conflicts in arch/x86/pci/{init.c,pci.h} due to
OLPC support manually.
This adds support for OLPC XO hardware. Open Firmware on XOs don't contain
the VSA, so it is necessary to emulate the PCI BARs in the kernel. This also
adds functionality for running EC commands, and a CONFIG_OLPC.
A number of OLPC drivers depend upon CONFIG_OLPC.
olpc_ec_timeout is a hack to work around Embedded Controller bugs.
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: geode_has_vsa build fix]
[akpm@linux-foundation.org: olpc_register_battery_callback doesn't exist]
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
so will disable that feature by default, and only enable that via
pci=check_enable_amd_mmconf or for system match with dmi table.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
normally BIOSes assign io/mmio range to different HT links without
overlapping, even same node same link should get non overlapping
entries.
but Rafael L. Wysocki's buggy BIOS creates a link with overlapping
entries for mmio and io:
node 0 link 0: io port [1000, ffffff]
node 0 link 0: mmio [e0000000, efffffff]
node 0 link 0: mmio [a0000, bffff]
node 0 link 0: mmio [80000000, ffffffff]
try to merge them and we will get:
bus: [00, ff] on node 0 link 0
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [80000000, fcffffffff]
bus: 00 index 2 mmio: [a0000, bffff]
so later we will reduce the chance to assign used resource to
unassigned device.
Reported-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Tested-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
if there's only one root bus there's no need to split resources.
This patch fixes the issue described at:
http://lkml.org/lkml/2008/4/10/304
Reported-and-bisected-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
some bioses give same range to mmconf for fam10h msr, and mmio for node/link.
fam10h msr will overide mmio for node/link.
so we can not assign range to devices under node/link for unassigned resources.
this patch will take range out from the mmio for node/link
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
scan AMD opteron io/mmio routing to make sure every pci root bus get correct
resource range. Thus later pci scan could assign correct resource to device
with unassigned resource.
this can fix a system without _CRS for multi pci root bus.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
... so we use the same code with Quad core cpu as old opteron.
This patch is useful when acpi=off or _PXM is not there in DSDT.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently, on an amd k8 system with multi ht chains, the numa_node of
pci devices under /sys/devices/pci0000:80/* is always 0, even if that
chain is on node 1 or 2 or 3.
Workaround: pcibus_to_node(bus) is used when we want to get the node that
pci_device is on.
In struct device, we already have numa_node member, and we could use
dev_to_node()/set_dev_node() to get and set numa_node in the device.
set_dev_node is called in pci_device_add() with pcibus_to_node(bus),
and pcibus_to_node uses bus->sysdata for nodeid.
The problem is when pci_add_device is called, bus->sysdata is not assigned
correct nodeid yet. The result is that numa_node will always be 0.
pcibios_scan_root and pci_scan_root could take sysdata. So we need to get
mp_bus_to_node mapping before these two are called, and thus
get_mp_bus_to_node could get correct node for sysdata in root bus.
In scanning of the root bus, all child busses will take parent bus sysdata.
So all pci_device->dev.numa_node will be assigned correctly and automatically.
Later we could use dev_to_node(&pci_dev->dev) to get numa_node, and we
could also could make other bus specific device get the correct numa_node
too.
This is an updated version of pci_sysdata and Jeff's pci_domain patch.
[ mingo@elte.hu: build fix ]
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
doesn't need to check if it is type1 or type2, we can use raw_pci_ops
directly.
also make pci_direct_conf1 static again.
anyway is there system with type 2 and mmconf support?
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
mmconfig is only used to access extended configuration space.
so don't need to reject MFG that only have one entry and only handle bus0.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so even booting kernel with acpi=off or even MCFG is not there, we still can
use MMCONFIG.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Greg KH <greg@kroah.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
reuse pci_cfg_space_size but skip check pci express and pci-x CAP ID.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Patch
"x86: validate against ACPI motherboard resources"
changed the mmconf init sequence, and init MMCONF late in acpi_init.
here change it back to old sequence:
1. check hostbridge in early
2. check MCFG with e820 in early
3. if all fail, will check MCFg with acpi _CRS in acpi_init
So we can make MCONF working again when acpi=off is set if hostbridge
support that.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For x86_64, need to free pci_mmcfg_virt, and iounmap some pointers
when MMCONF is not reserved in E820 or acpi _CRS and get rejected.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This path adds validation of the MMCONFIG table against the ACPI reserved
motherboard resources. If the MMCONFIG table is found to be reserved in
ACPI, we don't bother checking the E820 table. The PCI Express firmware
spec apparently tells BIOS developers that reservation in ACPI is required
and E820 reservation is optional, so checking against ACPI first makes
sense. Many BIOSes don't reserve the MMCONFIG region in E820 even though
it is perfectly functional, the existing check needlessly disables MMCONFIG
in these cases.
In order to do this, MMCONFIG setup has been split into two phases. If PCI
configuration type 1 is not available then MMCONFIG is enabled early as
before. Otherwise, it is enabled later after the ACPI interpreter is
enabled, since we need to be able to execute control methods in order to
check the ACPI reserved resources. Presently this is just triggered off
the end of ACPI interpreter initialization.
There are a few other behavioral changes here:
- Validate all MMCONFIG configurations provided, not just the first one.
- Validate the entire required length of each configuration according to
the provided ending bus number is reserved, not just the minimum required
allocation.
- Validate that the area is reserved even if we read it from the chipset
directly and not from the MCFG table. This catches the case where the
BIOS didn't set the location properly in the chipset and has mapped it
over other things it shouldn't have.
This also cleans up the MMCONFIG initialization functions so that they
simply do nothing if MMCONFIG is not compiled in.
Based on an original patch by Rajesh Shah from Intel.
[akpm@linux-foundation.org: many fixes and cleanups]
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andi Kleen <ak@suse.de>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the generic pci_enable_resources() instead of the arch-specific code.
Unlike this arch-specific code, the generic version:
- checks for resource collisions with "!r->parent"
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "pci=routeirq" option was added in 2004, and I don't get any valid
reports anymore. The option is still mentioned in kernel-parameters.txt.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PCI bus names included in /proc/iomem and /proc/ioports are
of the form 'PCI Bus #XX' where XX is the bus number. This patch
changes the naming to 'PCI Bus XXXX:YY' where XXXX is the domain
number and YY is the bus number. For example, PCI bus 14 in
domain 0 will show as 'PCI Bus 0000:14' instead of 'PCI Bus #14'.
This change makes the naming consistent with other architectures
such as ia64 where multiple PCI domain support has been around
longer.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function was obviously never being used since early 2.5 days as any
device that it would try to remove would never really be removed from
the system due to the PCI device list being held in the driver core, not
the general list of PCI devices.
As we have not had a single report of a problem here in 4 years, I think
it's safe to remove now.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We currently keep 2 lists of PCI devices in the system, one in the
driver core, and one all on its own. This second list is sorted at boot
time, in "BIOS" order, to try to remain compatible with older kernels
(2.2 and earlier days). There was also a "nosort" option to turn this
sorting off, to remain compatible with even older kernel versions, but
that just ends up being what we have been doing from 2.5 days...
Unfortunately, the second list of devices is not really ever used to
determine the probing order of PCI devices or drivers[1]. That is done
using the driver core list instead. This change happened back in the
early 2.5 days.
Relying on BIOS ording for the binding of drivers to specific device
names is problematic for many reasons, and userspace tools like udev
exist to properly name devices in a persistant manner if that is needed,
no reliance on the BIOS is needed.
Matt Domsch and others at Dell noticed this back in 2006, and added a
boot option to sort the PCI device lists (both of them) in a
breadth-first manner to help remain compatible with the 2.4 order, if
needed for any reason. This option is not going away, as some systems
rely on them.
This patch removes the sorting of the internal PCI device list in "BIOS"
mode, as it's not needed at all anymore, and hasn't for many years.
I've also removed the PCI flags for this from some other arches that for
some reason defined them, but never used them.
This should not change the ordering of any drivers or device probing.
[1] The old-style pci_get_device and pci_find_device() still used this
sorting order, but there are very few drivers that use these functions,
as they are deprecated for use in this manner. If for some reason, a
driver rely on the order and uses these functions, the breadth-first
boot option will resolve any problem.
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bug fixes for reserve_memtype() call in __ioremap and pci_mmap_page_range().
If reserve_memtype returns non-zero, then it is an error and subsequent free is
not required. Requested and returned prot value check should be done when
reserve_memtype returns success.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add reserve_memtype and free_memtype wrapper for pci_mmap_page_range. Free
is called on unmap, but identity map continues to be mapped as per
pci_mmap_page_range request, until next request for the same region calls
ioremap_change_attr(), which will go through without conflict. This way of
mapping is identical to one used in ioremap/iounmap.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove the last leftovers from the files. Move the ones
that are still used to the files they belong, the others
that grep can't reach, simply throw away.
Merge comments ontop of file and that's it: smpboot integrated
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
http://bugzilla.kernel.org/show_bug.cgi?id=10124
this change:
commit 08f1c192c3
Author: Muli Ben-Yehuda <muli@il.ibm.com>
Date: Sun Jul 22 00:23:39 2007 +0300
x86-64: introduce struct pci_sysdata to facilitate sharing of ->sysdata
This patch introduces struct pci_sysdata to x86 and x86-64, and
converts the existing two users (NUMA, Calgary) to use it.
This lays the groundwork for having other users of sysdata, such as
the PCI domains work.
The Calgary bits are tested, the NUMA bits just look ok.
replaces pcibios_scan_root by pci_scan_bus_parented...
but in pcibios_scan_root we have a check about scanned busses.
Cc: <yakui.zhao@intel.com>
Cc: Stian Jordet <stian@jordet.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Yinghai Lu" <yhlu.kernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I figured out another ACPI related regression today.
randconfig testing triggered an early boot-time hang on a laptop of mine
(32-bit x86, config attached) - the screen was scrolling ACPI AML
exceptions [with no serial port and no early debugging available].
v2.6.24 works fine on that laptop with the same .config, so after a few
hours of bisection (had to restart it 3 times - other regressions
interacted), it honed in on this commit:
| 10270d4838 is first bad commit
|
| Author: Linus Torvalds <torvalds@woody.linux-foundation.org>
| Date: Wed Feb 13 09:56:14 2008 -0800
|
| acpi: fix acpi_os_read_pci_configuration() misuse of raw_pci_read()
reverting this commit ontop of -rc5 gave a correctly booting kernel.
But this commit fixes a real bug so the real question is, why did it
break the bootup?
After quite some head-scratching, the following change stood out:
- pci_id->bus = tu8;
+ pci_id->bus = val;
pci_id->bus is defined as u16:
struct acpi_pci_id {
u16 segment;
u16 bus;
...
and 'tu8' changed from u8 to u32. So previously we'd unconditionally
mask the return value of acpi_os_read_pci_configuration()
(raw_pci_read()) to 8 bits, but now we just trust whatever comes back
from the PCI access routines and only crop it to 16 bits.
But if the high 8 bits of that result contains any noise then we'll
write that into ACPI's PCI ID descriptor and confuse the heck out of the
rest of ACPI.
So lets check the PCI-BIOS code on that theory. We have this codepath
for 8-bit accesses (arch/x86/pci/pcbios.c:pci_bios_read()):
switch (len) {
case 1:
__asm__("lcall *(%%esi); cld\n\t"
"jc 1f\n\t"
"xor %%ah, %%ah\n"
"1:"
: "=c" (*value),
"=a" (result)
: "1" (PCIBIOS_READ_CONFIG_BYTE),
"b" (bx),
"D" ((long)reg),
"S" (&pci_indirect));
Aha! The "=a" output constraint puts the full 32 bits of EAX into
*value. But if the BIOS's routines set any of the high bits to nonzero,
we'll return a value with more set in it than intended.
The other, more common PCI access methods (v1 and v2 PCI reads) clear
out the high bits already, for example pci_conf1_read() does:
switch (len) {
case 1:
*value = inb(0xCFC + (reg & 3));
which explicitly converts the return byte up to 32 bits and zero-extends
it.
So zero-extending the result in the PCI-BIOS read routine fixes the
regression on my laptop. ( It might fix some other long-standing issues
we had with PCI-BIOS during the past decade ... ) Both 8-bit and 16-bit
accesses were buggy.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We want to allow different implementations of pci_raw_ops for standard
and extended config space on x86. Rather than clutter generic code with
knowledge of this, we make pci_raw_ops private to x86 and use it to
implement the new raw interface -- raw_pci_read() and raw_pci_write().
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thanks to Loic Prylli <loic@myri.com>, who originally proposed
this idea.
Always using legacy configuration mechanism for the legacy config space
and extended mechanism (mmconf) for the extended config space is
a simple and very logical approach. It's supposed to resolve all
known mmconf problems. It still allows per-device quirks (tweaking
dev->cfg_size). It also allows to get rid of mmconf fallback code.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for flushing the chipsets on the 915, 945, 965 and G33
families of Intel chips.
The BIOS doesn't seem to always allocate the BAR on the 965 chipsets
so I have to use pci resource code to create a resource
It adds an export for pcibios_align_resource.
numa.c is the only user of the {in,out}*_quad functions. And it has only a few call
sites. Change them to open code the magic NUMAQ port access.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I can find no reason for the _p on the serverworks IRQ routing logic, and
a review of the documentation contains no indication that any such delay
is needed so lets try this
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
we use a few static mapping rules in our pirq routing functions,
and for example regression f3ac84324f was due to the pirq
being out of range of the remapping array. Put in a few
WARN_ON_ONCE() lines so that we get notified about any such
out-of-bound incidents.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
increasing number of PCI slots in large multi-node systems. The kernel
currently attempts by default to allocate memory for all PCI expansion
ROMs so there has also been an increasing number of PCI memory
allocation failures seen on these systems. This occurs because the BIOS
either (1) provides insufficient PCI memory resource for all the
expansion ROMs or (2) provides adequate PCI memory resource for
expansion ROMs but provides the space in kernel unexpected BIOS assigned
P2P non-prefetch windows.
The resulting PCI memory allocation failures may be benign when related
to memory requests for expansion ROMs themselves but in some cases they
can occur when attempting to allocate space for more critical BARs.
This can happen when a successful expansion ROM allocation request
consumes memory resource that was intended for a non-ROM BAR. We have
seen this happen during PCI hotplug of an adapter that contains a P2P
bridge where successful memory allocation for an expansion ROM BAR on
device behind the bridge consumed memory that was intended for a non-ROM
BAR on the P2P bridge. In all cases the allocation failure messages can
be very confusing for users.
This patch addresses the issue by changing the kernel default behavior
so that expansion ROM memory allocations are no longer attempted by
default when the BIOS has not assigned a specific address range to the
expansion ROM BAR. This was done by changing the 'pci=rom' boot option
behavior for BIOS unassigned expansion ROMs to actually match it's
current kernel-parameters.txt description which already implies "off" by
default. Behavior for BIOS assigned expansion ROMs implemented in
pcibios_assign_resources() [arch/x86/pci/i386.c] is unchanged.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jan Beulich <jbeulich@novell.com>
Acked-by: "Jun'ichi Nomura" <j-nomura@ce.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: fix APIC related bootup crash on Athlon XP CPUs
time: add ADJ_OFFSET_SS_READ
x86: export the symbol empty_zero_page on the 32-bit x86 architecture
x86: fix kprobes_64.c inlining borkage
pci: use pci=bfsort for HP DL385 G2, DL585 G2
x86: correctly set UTS_MACHINE for "make ARCH=x86"
lockdep: annotate do_debug() trap handler
x86: turn off iommu merge by default
x86: fix ACPI compile for LOCAL_APIC=n
x86: printk kernel version in WARN_ON and other dump_stack users
ACPI: Set max_cstate to 1 for early Opterons.
x86: fix NMI watchdog & 'stopped time' problem
HP ProLiant systems DL385 G2 and DL585 G2 need pci=bfsort to enumerate PCI
devices in the expected order.
Matt sayeth:
biosdevname is a userspace app I wrote to help solve this so we don't need
to patch the kernel for future systems. It's not integrated into any
distributions properly yet, but is included in openSUSE 10.3 and Fedora 8
for people who want to download and install it there. It acts as a udev
helper.
For the time being, patching the kernel is necessary. I really hope
biosdevname eliminates that need in future distributions.
http://linux.dell.com/biosdevname/
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Cc: mingo@elte.hu
Cc: andy@greyhouse.net
Cc: john.cagle@hp.com
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
need to check info->res_num less than PCI_BUS_NUM_RESOURCES, so
info->bus->resource[info->res_num] = res will not beyond of bus resource
array when acpi returns too many resource entries.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Gary Hade <gary.hade@us.ibm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch fixes the following section mismatches with CONFIG_HOTPLUG=n:
<-- snip -->
...
WARNING: vmlinux.o(.data+0x23640): Section mismatch: reference to .init.text.20:can_skip_ioresource_align (between 'acpi_pciprobe_dmi_table' and 'pcibios_irq_mask')
WARNING: vmlinux.o(.data+0x2366c): Section mismatch: reference to .init.text.20:can_skip_ioresource_align (between 'acpi_pciprobe_dmi_table' and 'pcibios_irq_mask')
WARNING: vmlinux.o(.data+0x23698): Section mismatch: reference to .init.text.20:can_skip_ioresource_align (between 'acpi_pciprobe_dmi_table' and 'pcibios_irq_mask')
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Len Brown <len.brown@intel.com>
HP ProLiant systems DL385 G2 and DL585 G2 need pci=bfsort to enumerate PCI
devices in the expected order.
Matt sayeth:
biosdevname is a userspace app I wrote to help solve this so we don't need
to patch the kernel for future systems. It's not integrated into any
distributions properly yet, but is included in openSUSE 10.3 and Fedora 8
for people who want to download and install it there. It acts as a udev
helper.
For the time being, patching the kernel is necessary. I really hope
biosdevname eliminates that need in future distributions.
http://linux.dell.com/biosdevname/
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Cc: <john.cagle@hp.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix DMI const-ification fallout that appeared when merging subsystem
trees.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* fix bug in pci_read() and pci_write() which prevented PCI domain
support from working (hardcoded domain 0).
* unconditionally enable CONFIG_PCI_DOMAINS
* implement pci_domain_nr() and pci_proc_domain(), as required of
all arches when CONFIG_PCI_DOMAINS is enabled.
* store domain in struct pci_sysdata, as assigned by ACPI
* support "pci=nodomains"
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify PCI Bridge Control ISA flag for clarity
This patch changes PCI_BRIDGE_CTL_NO_ISA to PCI_BRIDGE_CTL_ISA
and modifies it's clarifying comment and locations where used.
The change reduces the chance of future confusion since it makes
the set/unset meaning of the bit the same in both the bridge
control register and bridge_ctl field of the pci_bus struct.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use _CRS for PCI resource allocation
This patch resolves an issue where incorrect PCI memory and i/o ranges
are being assigned to hotplugged PCI devices on some IBM systems. The
resource mis-allocation not only makes the PCI device unuseable but
often makes the entire system unuseable due to resulting machine checks.
The hotplug capable PCI slots on the affected systems are not located
under a standard P2P bridge but are instead located under PCI root
bridges or subtractive decode P2P bridges. For example, the IBM x3850
contains 2 hotplug capable PCI-X slots and 4 hotplug capable PCIe slots
with the PCI-X slots each located under a PCI root bridge and the PCIe
slots each located under a subtractive decode P2P bridge.
The current i386/x86_64 PCI resource allocation code does not use _CRS
returned resource information. No other resource information source is
available for slots that are not below a standard P2P bridge so
incorrect ranges are being allocated from e820 hole causing the bad
result.
This patch causes the kernel to use _CRS returned resource info. It is
roughly based on a change provided by Matthew Wilcox for the ia64 kernel
in 2005. Due to possible buggy BIOS factor and possible yet to be
discovered kernel issues the function is disabled by default and can be
enabled with pci=use_crs.
Signed-off-by: Gary Hade <gary.hade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Skip ISA ioresource alignment on some systems
To conserve limited PCI i/o resource on some IBM multi-node systems, the
BIOS allocates (via _CRS) and expects the kernel to use addresses in
ranges currently excluded by pcibios_align_resource() [i386/pci/i386.c].
This change allows the kernel to use the currently excluded address
ranges on the IBM x3800, x3850, and x3950.
Signed-off-by: Gary Hade <gary.hade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Force PCI bus renumbering for Compaq EVO N800c laptop, in order to get
the cardbus slot recognised.
Signed-off-by: Juha Laiho <Juha.Laiho@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On the "MSI K8T Neo2-FIR" board the BIOS disables the onboard
soundcard, if a second PCI soundcard is present.
This patch sets the korrect register bit to enable the onboard sound.
Removed old code in /drivers/pci/quirks.c that only checks for the
PCI-ID and fires on any Board with VIA 8237.
New code in /arch/i386/pci/fixup.c checks the DMI-tables and only runs
on the specific board.
Signed-off-by: Johannes Goecke <goecke@upb.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for PicoPower PT86C523 IRQ router to be used with the in-kernel
yenta driver for CardBus. With this patch cardbus works on e.g. Dell
Latitude XPi P150CD.
Initial patch for kernel 2.4 series by Sune Mølgaard
http://molgaard.org/code/linux-2.4.31-picopower.patch
Ported to 2.6.20 by Chmouel Boudjnah (http://www.chmouel.com)
Testing and confirmation that it works by Austin Acton
Cleaned up a little for inclusion in a 2.6.21-rc7 based kernel.
Added some more cleanups according to CodingStyle, as noted by
Randy Dunlap on LKML.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Thomas Backlund <tmb@mandriva.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kulikov Vasiliy