Atomic pool should always be allocated from DMA zone if such zone is
available in the system to avoid issues caused by limited dma mask of
any of the devices used for making an atomic allocation.
Reported-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Stable <stable@vger.kernel.org> [v3.6+]
In the UAPI header files, __BIG_ENDIAN and __LITTLE_ENDIAN must be
compared against __BYTE_ORDER in preprocessor conditionals where these are
exposed to userspace (that is they're not inside __KERNEL__ conditionals).
However, in the main kernel the norm is to check for
"defined(__XXX_ENDIAN)" rather than comparing against __BYTE_ORDER and
this has incorrectly leaked into the userspace headers.
The definition of struct stat64 in M32R's asm/stat.h is wrong in this way.
Note that userspace will likely interpret the field order incorrectly as
the big-endian variant on little-endian machines - depending on header
inclusion order.
[!!!] NOTE [!!!] This patch may adversely change the userspace API. It might
be better to fix the ordering of st_blocks and __pad4 in struct stat64.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Create a sysfs entry, '/sys/bus/event_source/devices/cpu/format/event'
which describes the format of the POWER7 PMU events.
This code is based on corresponding code in x86.
Changelog[v4]: [Michael Ellerman, Paul Mckerras] The event format is different
for other POWER cpus. So move the code to POWER7-specific,
power7-pmu.c Also, the POWER7 format uses bits 0-19 not 0-20.
Changelog[v2]: [Jiri Osla] Use PMU_FORMAT_ATTR rather than duplicating code.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Tested-by: Michael Ellerman <michael@ellerman.id.au>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Anton Blanchard <anton@au1.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: benh@kernel.crashing.org
Cc: linuxppc-dev@ozlabs.org
Link: http://lkml.kernel.org/r/20130306054826.GA14627@us.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
There was only chip enable and readdy/busy pins for the nand controller.
This add the rest of the pins.
pinctrl_nand_16bits contains the specific muxes for 16 bits NANDs.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Comments on NAND pins where inverted.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The recent move to GPIO descriptors breaks the OpenRISC build. Requiring
gpiolib resolves this; using gpiolib exclusively is also the recommended
way forward for all arches by the developers working on these GPIO changes.
The non-gpiolib implementation for OpenRISC never worked anyway...
Signed-off-by: Jonas Bonn <jonas@southpole.se>
* Compile warnings and errors (one on x86, two on ARM)
* WARNING in xen-pciback
* Use the acpi_processor_get_performance_info instead of the 'register' version
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJRP33uAAoJEFjIrFwIi8fJfxMIAJxK7jI7NghJ87b8uk3IrkDl
VDsY5Re86XWE0HjsFDJXfWZCGumhpMb8hI1RJBavLDWQmk4THBqsKbx9rDgRZUJO
HepvhwD/RdK+nnjVmbAzJKuc7aOKQmeEW3Weysb32DW9C5Wg27LRrto/oVJIUsyj
4HrLcsZZqCiEYUZjGwrkrMC1yXx+2XvkX9mXq81hGj0xU4X1hMizwBAJvSE5lKca
r4LaCoZ0SuayHYHjEtxyjAcu39wnMdlCkdW9DUlqrjK7L3X29ifVvnb+aS951O5E
t57DCHY8WkI1BkaoHaAQqI7/Y1HpYbT8BALVmxXoIInI9lc8VLHZOs8/fVVDppQ=
=MxoB
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.9-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
- Compile warnings and errors (one on x86, two on ARM)
- WARNING in xen-pciback
- Use the acpi_processor_get_performance_info instead of the 'register'
version
* tag 'stable/for-linus-3.9-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/acpi: remove redundant acpi/acpi_drivers.h include
xen: arm: mandate EABI and use generic atomic operations.
acpi: Export the acpi_processor_get_performance_info
xen/pciback: Don't disable a PCI device that is already disabled.
Fix regression introduced by commit d2323cf773 ("onewire: w1-gpio: add
ext_pullup_enable pin in platform data") which added a gpio entry to the
platform data, but did not add the required initialisers to the board
files using it. Consequently, the driver would request gpio 0 at probe,
which could break other uses of the corresponding pin.
On AT91 requesting gpio 0 changes the pin muxing for PIOA0, which, for
instance, breaks SPI0 on at91sam9g20.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5ac47f7a6e (powerpc: Relocate prom_init.c on 64bit) made
prom_init.c position independent by manually relocating its entries
in the TOC.
We get the address of the TOC entries with the __prom_init_toc_start
linker symbol. If __prom_init_toc_start ends up as an entry in the
TOC then we need to add an offset to get the current address. This is
the case for older toolchains.
On the other hand, if we have a newer toolchain that supports
-mcmodel=medium then __prom_init_toc_start will be created by a
relative offset from r2 (the TOC pointer). Since r2 has already been
relocated, nothing more needs to be done. Adding an offset in this
case is wrong and Aaro Koskinen and Alexander Graf have noticed noticed
G5 and OpenBIOS breakage.
Alan Modra suggested we just use r2 to get at the TOC which is simpler
and works with both old and new toolchains.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Anton Blanchard <anton@samba.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Kconfig symbol POWER4_ONLY got removed in commit
694caf0255 ("powerpc: Remove
CONFIG_POWER4_ONLY"). Remove its last traces.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 44ae3ab335 forgot to update
the entry for the 970MP rev 1.0 processor when moving some CPU
features bits to the MMU feature bit mask. This breaks booting
on some rare G5 models using that chip revision.
Reported-by: Phileas Fogg <phileas-fogg@mail.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.0+]
Commit f5339277eb accidentally removed
more than just iSeries bits and took out the call to stab_initialize()
thus breaking support for POWER3 processors.
Put it back. (Yes, nobody noticed until now ...)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.4+]
In commit 887cbce0ad ("arch Kconfig: centralise ARCH_NO_VIRT_TO_BUS")
I introduced the config sybmol HAVE_VIRT_TO_BUS and selected that where
needed. I am not sure what I was thinking. Instead, just directly
select VIRT_TO_BUS where it is needed.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These bug fixes are for the largest part for mvebu/kirkwood, which
saw a few regressions after the clock infrastructure was enabled,
and for OMAP, which showed a few more preexisting bugs with
the new multiplatform support.
Other small fixes are for imx, mxs, tegra, spear and socfpga.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yq5v
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"These bug fixes are for the largest part for mvebu/kirkwood, which saw
a few regressions after the clock infrastructure was enabled, and for
OMAP, which showed a few more preexisting bugs with the new
multiplatform support.
Other small fixes are for imx, mxs, tegra, spear and socfpga"
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: spear3xx: Use correct pl080 header file
Arm: socfpga: pl330: Add #dma-cells for generic dma binding support
ARM: multiplatform: Sort the max gpio numbers.
ARM: imx: fix typo "DEBUG_IMX50_IMX53_UART"
ARM: imx: pll1_sys should be an initial on clk
arm: mach-orion5x: fix typo in compatible string of a .dts file
arm: mvebu: fix address-cells in mpic DT node
arm: plat-orion: fix address decoding when > 4GB is used
arm: mvebu: Reduce reg-io-width with UARTs
ARM: Dove: add RTC device node
arm: mvebu: enable the USB ports on Armada 370 Reference Design board
ARM: dove: drop "select COMMON_CLK_DOVE"
rtc: rtc-mv: Add support for clk to avoid lockups
gpio: mvebu: Add clk support to prevent lockup
ARM: kirkwood: fix to retain gbe MAC addresses for DT kernels
ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency
ARM: mxs: cfa10049: Fix fb initialisation function
ARM: SPEAr13xx: Fix typo "ARCH_HAVE_CPUFREQ"
ARM: OMAP: RX-51: add missing USB phy binding
clk: Tegra: Remove duplicate smp_twd clock
...
Pull m68knommu fixes from Greg Ungerer:
"It contains a few small fixes for the non-MMU m68k platforms. Fixes
some compilation problems, some broken header definitions, removes an
unused config option and adds a name for the old 68000 CPU support."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: drop "select EMAC_INC"
m68knommu: fix misnamed GPIO pin definition for ColdFire 528x CPU
m68knommu: fix MC68328.h defines
m68knommu: fix build when CPU is not coldfire
m68knommu: add CPU_NAME for 68000
k is u32 which never < 0, need type cast, or cause issue.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
that was introduced with EDMA DMA engine
conversion. The bug has been there since
v3.7 and has been marked for stable update.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=pToj
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.9-rc/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
Via Sekhar Nori <nsekhar@ti.com>:
This patch fixes a boot breakage on DA830
that was introduced with EDMA DMA engine
conversion. The bug has been there since
v3.7 and has been marked for stable update.
* tag 'davinci-for-v3.9-rc/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: edma: fix dmaengine induced null pointer dereference on da830
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 455bd4c430 ("ARM: 7668/1: fix memset-related crashes caused by
recent GCC (4.7.2) optimizations") attempted to fix a compliance issue
with the memset return value. However the memset itself became broken
by that patch for misaligned pointers.
This fixes the above by branching over the entry code from the
misaligned fixup code to avoid reloading the original pointer.
Also, because the function entry alignment is wrong in the Thumb mode
compilation, that fixup code is moved to the end.
While at it, the entry instructions are slightly reworked to help dual
issue pipelines.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds additional error checking to the private edma api implementation
to catch the case where the edma_alloc_slot() has an invalid controller
parameter. The edma dmaengine wrapper driver relies on this condition
being handled in order to avoid setting up a second edma dmaengine
instance on DA830.
Verfied using a DA850 with the second EDMA controller platform instance
removed to simulate a DA830 which only has a single EDMA controller.
Reported-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Matt Porter <mporter@ti.com>
Cc: stable@vger.kernel.org # v3.7.x+
Tested-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The definitions have move around recently, causing build errors
in spear3xx for all configurations:
spear3xx.c:47:5: error: 'PL080_BSIZE_16' undeclared here (not in a function)
spear3xx.c:47:23: error: 'PL080_CONTROL_SB_SIZE_SHIFT' undeclared here (not in a function)
spear3xx.c:48:22: error: 'PL080_CONTROL_DB_SIZE_SHIFT' undeclared here (not in a function)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alessandro Rubini <rubini@gnudd.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
The ab8500 device is a child of the prcmu device, which is a memory mapped
bus device, whose children are addressable using physical memory addresses,
not using mailboxes, so a mailbox number in the ab8500 node cannot be
parsed by DT. Nothing uses this number, since it was only introduced
as part of the failed attempt to clean up prcmu mailbox handling, and
we can simply remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds #dma-cells property to PL330 DMA controller nodes for
supporting generic dma dt bindings on SOCFPGA platform. #dma-channels
and #dma-requests are not required now but added in advance.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The first four patches:
89c58c1 rtc: rtc-mv: Add support for clk to avoid lockups
de88747 gpio: mvebu: Add clk support to prevent lockup
7bf5b40 ARM: kirkwood: fix to retain gbe MAC addresses for DT kernels
93fff4c ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency
are Cc'd to stable since they were held over from the previous merge window.
The rest are a small collection of fixes and a couple of devicetree conversion
catchups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJROmXfAAoJEAi3KVZQDZAeahAIAIWybkKuD/lKLRPU3FmS59gM
gdcPxQcjFnldRRBQFXRfSQ4acFNEWZwDgHXs0gpKsUCoZ2w/tCbjba0sNb2vWsmc
H4Nh8MU3CqHIuGDFSmsbDHX0BNrp6JvZLxiY7vtswTDqZt1K/UKb7obnnbAo8ygu
OtbGItfYNTjMJ0B1Ar2eYCoA4V29SFzXB+ymWEHl4u9Vmwasr0uervjHhyq+3tU1
pCNPWc98N9r0VqniVbbTqVuwlwoc3IZmbiv1T9EGMw2PDbtcIJLwY7oxlSb0kW3e
QIookCxlItX1A360TmGI4xKnSRR42ZinNmn2AuLetW8ydnRNDwkyrRJZ2VsbQLE=
=mme/
-----END PGP SIGNATURE-----
Merge tag 'mvebu_fixes_for_v3.9' of git://git.infradead.org/users/jcooper/linux into fixes
mvebu fixes for v3.9 from Jason Cooper <jason@lakedaemon.net>:
The first four patches:
89c58c1 rtc: rtc-mv: Add support for clk to avoid lockups
de88747 gpio: mvebu: Add clk support to prevent lockup
7bf5b40 ARM: kirkwood: fix to retain gbe MAC addresses for DT kernels
93fff4c ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency
are Cc'd to stable since they were held over from the previous merge window.
The rest are a small collection of fixes and a couple of devicetree conversion
catchups.
* tag 'mvebu_fixes_for_v3.9' of git://git.infradead.org/users/jcooper/linux:
arm: mach-orion5x: fix typo in compatible string of a .dts file
arm: mvebu: fix address-cells in mpic DT node
arm: plat-orion: fix address decoding when > 4GB is used
arm: mvebu: Reduce reg-io-width with UARTs
ARM: Dove: add RTC device node
arm: mvebu: enable the USB ports on Armada 370 Reference Design board
ARM: dove: drop "select COMMON_CLK_DOVE"
rtc: rtc-mv: Add support for clk to avoid lockups
gpio: mvebu: Add clk support to prevent lockup
ARM: kirkwood: fix to retain gbe MAC addresses for DT kernels
ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix pll1_sys clk initial status
- Fix a typo in imx DEBUG_LL Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRPeaEAAoJEFBXWFqHsHzOIFgH/RNeNudfIZ5yBaP0xWu1h9lm
gxvXRJshzQOYovT0qDL6w7/ia57b4b8zGQlbR8x86U7EjqFdgrAhYeI12dVwDEAf
165MM1h0f36w5wAQqjGE1isTVUpl29zPDLSIg87t1AnBARtrhwwhKKjIF9lT+Sc9
ar94MphjgPwIgDnflVqQl0IGW4DI+Zc6VZLzpBvcmN33J/K3owhAtr4F+pLSXsnR
5NH2ml37IUgDqQpo2OFQk4mysPCv797Hl6SHXbFLIaDiYi91jhJ7YzDrnI8v7evH
tTpWDrkR6o/uG9+77mhhtp8LR0BVBLPgBfy8FXNdW13LXn0qbKArkxe9iILmlSw=
=8nT7
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.9-2' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The 2nd take of imx fixes for 3.9:
- Fix pll1_sys clk initial status
- Fix a typo in imx DEBUG_LL Kconfig
* tag 'imx-fixes-3.9-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: fix typo "DEBUG_IMX50_IMX53_UART"
ARM: imx: pll1_sys should be an initial on clk
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix an error caused by incorrect conflict resolution when
applying the patch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRPeg/AAoJEFBXWFqHsHzOmkEH/3mjPeA/bmly/LuUWd2BdS8W
VbKzKKBJpXa34wFnj1aH2ydViPs4PWHHIxB2Z3u+epu+43w+DdDtjrM1XdX8lAYN
5z90l5ZYXoeq2H3xaqCwCzHzp0FwxbrxmXN9Kr97pOxefAJMmpO8/yrMgtO2ADAd
f3Z8wQCM7J4QRjCAHd+8sPsDfnkkGtMdlLsD3I2IRbBOU15LdaFVd1zXGbi/M/wo
rW/3aZ9YbJSuOdwQ8ucGnNp+ZXiUUCPy9DDplt7yfpQkKhML/fqz3t6bznaZs/YD
UWtqiP/wfVTlz9yhRCLOPoGU/ix8Rmk1ltZtTvqNY+b9JLsnFiwwK8Ngo4C5IcE=
=TYXe
-----END PGP SIGNATURE-----
Merge tag 'mxs-fixes-3.9-2' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The 2nd mxs fixes for 3.9:
- Fix an error caused by incorrect conflict resolution when
applying the patch
* tag 'mxs-fixes-3.9-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: cfa10049: Fix fb initialisation function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When building a multiplatform kernel, we could end up with a smaller
number of GPIOs than the one required by the platform the kernel was
running on.
Sort the max GPIO number by descending order so that we always take the
highest number required.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rob Herring has observed that c81611c4e9 "xen: event channel arrays are
xen_ulong_t and not unsigned long" introduced a compile failure when building
without CONFIG_AEABI:
/tmp/ccJaIZOW.s: Assembler messages:
/tmp/ccJaIZOW.s:831: Error: even register required -- `ldrexd r5,r6,[r4]'
Will Deacon pointed out that this is because OABI does not require even base
registers for 64-bit values. We can avoid this by simply using the existing
atomic64_xchg operation and the same containerof trick as used by the cmpxchg
macros. However since this code is used on memory which is shared with the
hypervisor we require proper atomic instructions and cannot use the generic
atomic64 callbacks (which are based on spinlocks), therefore add a dependency
on !GENERIC_ATOMIC64. Since we already depend on !CPU_V6 there isn't much
downside to this.
While thinking about this we also observed that OABI has different struct
alignment requirements to EABI, which is a problem for hypercall argument
structs which are shared with the hypervisor and which must be in EABI layout.
Since I don't expect people to want to run OABI kernels on Xen depend on
CONFIG_AEABI explicitly too (although it also happens to be enforced by the
!GENERIC_ATOMIC64 requirement too).
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Rob Herring <robherring2@gmail.com>
Acked-by: Stefano Stabellini <Stefano.Stabellini@eu.citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Pull perf fixes from Ingo Molnar:
"Misc minor fixes mostly related to tracing"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
s390: Fix a header dependencies related build error
tracing: update documentation of snapshot utility
tracing: Do not return EINVAL in snapshot when not allocated
tracing: Add help of snapshot feature when snapshot is empty
ftrace: Update the kconfig for DYNAMIC_FTRACE
Commit f8c95fe (ARM: imx: support DEBUG_LL uart port selection for all
i.MX SoCs) had a typo that DEBUG_IMX50_IMX53_UART should be
DEBUG_IMX53_UART.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The following patch adds support for correctly
recognizing SPARC-X chips.
cpu : Unknown SUN4V CPU
fpu : Unknown SUN4V FPU
pmu : Unknown SUN4V PMU
Signed-off-by: Katayama Yoshihiro <kata1@jp.fujitsu.com>
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 877c685607
("perf: Remove include of cgroup.h from perf_event.h") caused
this build failure if PERF_EVENTS is enabled:
In file included from arch/s390/include/asm/perf_event.h:9:0,
from include/linux/perf_event.h:24,
from kernel/events/ring_buffer.c:12:
arch/s390/include/asm/cpu_mf.h: In function 'qctri':
arch/s390/include/asm/cpu_mf.h:61:12: error: 'EINVAL' undeclared (first use in this function)
cpu_mf.h had an implicit errno.h dependency, which was added
indirectly via cgroups.h but not anymore. Add it explicitly.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Li Zefan <lizefan@huawei.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Link: http://lkml.kernel.org/r/51385F79.7000106@huawei.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The tty below tty_port might get destroyed by the tty layer
while we hold a reference to it.
So we have to carry tty_port around...
Signed-off-by: Richard Weinberger <richard@nod.at>
As we setup the SIGWINCH handler in tty_port_operations->activate
it makes sense to tear down it in ->destruct.
Signed-off-by: Richard Weinberger <richard@nod.at>
arch/um/os-Linux/signal.c:18:8: error: conflicting types for 'sig_info'
In file included from /home/slyfox/linux-2.6/arch/um/os-Linux/signal.c:12:0:
arch/um/include/shared/as-layout.h:64:15: note: previous declaration of 'sig_info' was here
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
CC: Jeff Dike <jdike@addtoit.com>
CC: Richard Weinberger <richard@nod.at>
CC: "Martin Pärtel" <martin.partel@gmail.com>
CC: Al Viro <viro@zeniv.linux.org.uk>
CC: user-mode-linux-devel@lists.sourceforge.net
CC: user-mode-linux-user@lists.sourceforge.net
CC: linux-kernel@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
arch/um/os-Linux/start_up.c: In function 'check_coredump_limit':
arch/um/os-Linux/start_up.c:338:16: error: storage size of 'lim' isn't known
arch/um/os-Linux/start_up.c:339:2: error: implicit declaration of function 'getrlimit' [-Werror=implicit-function-declaration]
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
CC: Jeff Dike <jdike@addtoit.com>
CC: Richard Weinberger <richard@nod.at>
CC: Al Viro <viro@zeniv.linux.org.uk>
CC: user-mode-linux-devel@lists.sourceforge.net
CC: user-mode-linux-user@lists.sourceforge.net
CC: linux-kernel@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
This new version moves the skb_tx_timestamp in the main uml
driver. This should avoid the need to call this function in each
transport (vde, slirp, tuntap, ...). It also add support for ethtool
get_ts_info.
Signed-off-by: Paul Chavent <paul.chavent@onera.fr>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
We always boot from PLL1, so let's have pll1_sys in the clks_init_on
list to have clk prepare/enable use count match the hardware status,
so that drivers managing pll1_sys like cpufreq can get the use count
right from the start.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Pull namespace bugfixes from Eric Biederman:
"This is three simple fixes against 3.9-rc1. I have tested each of
these fixes and verified they work correctly.
The userns oops in key_change_session_keyring and the BUG_ON triggered
by proc_ns_follow_link were found by Dave Jones.
I am including the enhancement for mount to only trigger requests of
filesystem modules here instead of delaying this for the 3.10 merge
window because it is both trivial and the kind of change that tends to
bit-rot if left untouched for two months."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
proc: Use nd_jump_link in proc_ns_follow_link
fs: Limit sys_mount to only request filesystem modules (Part 2).
fs: Limit sys_mount to only request filesystem modules.
userns: Stop oopsing in key_change_session_keyring
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
alpha: boot: fix build breakage introduced by system.h disintegration
memcg: initialize kmem-cache destroying work earlier
Randy has moved
ksm: fix m68k build: only NUMA needs pfn_to_nid
dmi_scan: fix missing check for _DMI_ signature in smbios_present()
Revert parts of "hlist: drop the node parameter from iterators"
idr: remove WARN_ON_ONCE() on negative IDs
mm/mempolicy.c: fix sp_node_init() argument ordering
mm/mempolicy.c: fix wrong sp_node insertion
ipc: don't allocate a copy larger than max
ipc: fix potential oops when src msg > 4k w/ MSG_COPY
Commit ec2212088c ("Disintegrate asm/system.h for Alpha") removed the
system.h include from boot/head.S, which puts the PAL_* asm constants
out of scope.
Include <asm/pal.h> so we can get building again.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: David Rusling <david.rusling@linaro.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull tile architecture fixes from Chris Metcalf:
"This fixes the bug that Al Viro spotted with the compat llseek code.
I also fixed the compat syscall definitions to use the new syscall
define macros to properly sign-extend their arguments."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: properly use COMPAT_SYSCALL_DEFINEx
tile: work around bug in the generic sys_llseek
- remove SET_PERSONALITY(): use default definition like other arches
now do.
- inhibit NUMA balancing: like SH, NUMA is used for memories with
different latencies. ARCH_WANT_VARIABLE_LOCALITY has been added for
this purpose.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=FG5k
-----END PGP SIGNATURE-----
Merge tag 'metag-for-v3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull metag bugfixes from James Hogan:
"A couple of fairly minor arch/metag integration fixes from v3.9-rc1:
- remove SET_PERSONALITY(): use default definition like other arches
now do.
- inhibit NUMA balancing: like SH, NUMA is used for memories with
different latencies. ARCH_WANT_VARIABLE_LOCALITY has been added
for this purpose."
* tag 'metag-for-v3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: Inhibit NUMA balancing.
metag: remove SET_PERSONALITY()
The orion5x-lacie-ethernet-disk-mini-v2.dts file was using
"marvell-orion5x-88f5182" as a compatible string, while it should have
been "marvell,orion5x-88f5182".
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
There is no need to have a #address-cells property in the MPIC Device
Tree node, and more than that, having it confuses the of_irq_map_raw()
logic, which will be used by the Marvell PCIe driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
During the system initialization, the orion_setup_cpu_mbus_target()
function reads the SDRAM address decoding registers to find out how
many chip-selects of SDRAM have been enabled, and builds a small array
with one entry per chip-select. This array is then used by device
drivers (XOR, Ethernet, etc.) to configure their own address decoding
windows to the SDRAM.
However, devices can only access the first 32 bits of the physical
memory. Even though LPAE is not supported for now, some Marvell boards
are now showing up with 8 GB of RAM, configured using two SDRAM
address decoding windows: the first covering the first 4 GB, the
second covering the last 4 GB. The array built by
orion_setup_cpu_mbus_target() has therefore two entries, and device
drivers try to set up two address decoding windows to the
SDRAM. However, in the device registers for the address decoding, the
base address is only 32 bits, so those two windows overlap each other,
and the devices do not work at all.
This patch makes sure that the array built by
orion_setup_cpu_mbus_target() only contains the SDRAM decoding windows
that correspond to the first 4 GB of the memory. To do that, it
ignores the SDRAM decoding windows for which the 4 low-order bits are
not zero (the 4 low-order bits of the base register are used to store
bits 32:35 of the base address, so they actually indicate whether the
base address is above 4 GB).
This patch allows the newly introduced armada-xp-gp board to properly
operate when it is mounted with more than 4 GB of RAM. Without that,
all devices doing DMA (for example XOR and Ethernet) do not work at
all.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Setting the reg-io-width to 1 byte represents more accurate
description of the HW.
This will fix an issue where UART driver causes kernel
panic during bootup. Gregory CLEMENT traced the issue to
autoconfig() in 8250.c, where the existence of FIFO is
checked from UART_IIR register. The register is now read as
32-bit value as the reg-io-width is set to 4-bytes. The
retuned value seems to contain bogus data for bits 31:8,
causing the issue.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The commit:
48be9ac ARM: Dove: split legacy and DT setup
removed the RTC initialization. This patch re-enables the RTC
via the DT.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch modifies the Armada 370 Reference Design DTS file to enable
support for the two USB ports found on this board.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Commit 5b03df9ace ("ARM: dove: switch to
DT clock providers") added "select COMMON_CLK_DOVE" to Marvell Dove's
Kconfig entry. But there's no Kconfig symbol COMMON_CLK_DOVE, which
makes this select statement a nop. It's probably a leftover of some
experimental code that never hit mainline. Drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the
driver clk_prepare_enable() this clock, otherwise there is a danger
the SoC will lockup when accessing RTC registers with the clock
disabled.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The kirkwood SoC GPIO cores use the runit clock. Add code to
clk_prepare_enable() runit, otherwise there is a danger of locking up
the SoC by accessing the GPIO registers when runit clock is not
ticking.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ethernet controller used on kirkwood looses its MAC address
register contents when the corresponding clock is gated. As soon as
mv643xx_eth is built as module, the clock gets gated and when loading
the module, the MAC address is gone.
Proper DT support for the mv643xx_eth driver is expected soon, so we add
a workaround to always enable ge0/ge1 clocks on kirkwood. This workaround
is also already used on non-DT kirkwood kernels.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When DT support for kirkwood was first introduced, there was no clock
infrastructure. As a result, we had to manually pass the
clock-frequency to the driver from the device node.
Unfortunately, on kirkwood, with minimal config or all module configs,
clock-frequency breaks booting because of_serial doesn't consume the
gate_clk when clock-frequency is defined.
The end result on kirkwood is that runit gets gated, and then the boot
fails when the kernel tries to write to the serial port.
Fix the issue by removing the clock-frequency parameter from all
kirkwood dts files.
Booted on dreamplug without earlyprintk and successfully logged in via
ttyS0.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
mmc/host.h provides MMC_CAP_SD_HIGHSPEED which is used in board-marzen.c
This resolves a build problem observed when compiling with
"mmc: tmio: remove unused and deprecated symbols" applied.
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull x86 fixes from Peter Anvin:
"Several boot fixes (MacBook, legacy EFI bootloaders), another
please-don't-brick fix, and some minor stuff."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Do not try to sync identity map for non-mapped pages
x86, doc: Be explicit about what the x86 struct boot_params requires
x86: Don't clear efi_info even if the sentinel hits
x86, mm: Make sure to find a 2M free block for the first mapped area
x86: Fix 32-bit *_cpu_data initializers
efivarfs: return accurate error code in efivarfs_fill_super()
efivars: efivarfs_valid_name() should handle pstore syntax
efi: be more paranoid about available space when creating variables
iommu, x86: Add DMA remap fault reason
x86, smpboot: Remove unused variable
Pull ARM fixes from Russell King:
"Mainly a group of fixes, the only exception is the wiring up of the
kcmp syscall now that those patches went in during the last merge
window."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7668/1: fix memset-related crashes caused by recent GCC (4.7.2) optimizations
ARM: 7667/1: perf: Fix section mismatch on armpmu_init()
ARM: 7666/1: decompressor: add -mno-single-pic-base for building the decompressor
ARM: 7665/1: Wire up kcmp syscall
ARM: 7664/1: perf: remove erroneous semicolon from event initialisation
ARM: 7663/1: perf: fix ARMv7 EVTYPE_MASK to include NSH bit
ARM: 7662/1: hw_breakpoint: reset debug logic on secondary CPUs in s2ram resume
ARM: 7661/1: mm: perform explicit branch predictor maintenance when required
ARM: 7660/1: tlb: add branch predictor maintenance operations
ARM: 7659/1: mm: make mm->context.id an atomic64_t variable
ARM: 7658/1: mm: fix race updating mm->context.id on ASID rollover
ARM: 7657/1: head: fix swapper and idmap population with LPAE and big-endian
ARM: 7655/1: smp_twd: make twd_local_timer_of_register() no-op for nosmp
ARM: 7652/1: mm: fix missing use of 'asid' to get asid value from mm->context.id
ARM: 7642/1: netx: bump IRQ offset to 64
kernel_map_sync_memtype() is called from a variety of contexts. The
pat.c code that calls it seems to ensure that it is not called for
non-ram areas by checking via pat_pagerange_is_ram(). It is important
that it only be called on the actual identity map because there *IS*
no map to sync for highmem pages, or for memory holes.
The ioremap.c uses are not as careful as those from pat.c, and call
kernel_map_sync_memtype() on PCI space which is in the middle of the
kernel identity map _range_, but is not actually mapped.
This patch adds a check to kernel_map_sync_memtype() which probably
duplicates some of the checks already in pat.c. But, it is necessary
for the ioremap.c uses and shouldn't hurt other callers.
I have reproduced this bug and this patch fixes it for me and the
original bug reporter:
https://lkml.org/lkml/2013/2/5/396
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20130307163151.D9B58C4E@kernel.stglabs.ibm.com
Signed-off-by: Dave Hansen <dave@sr71.net>
Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Recent GCC versions (e.g. GCC-4.7.2) perform optimizations based on
assumptions about the implementation of memset and similar functions.
The current ARM optimized memset code does not return the value of
its first argument, as is usually expected from standard implementations.
For instance in the following function:
void debug_mutex_lock_common(struct mutex *lock, struct mutex_waiter *waiter)
{
memset(waiter, MUTEX_DEBUG_INIT, sizeof(*waiter));
waiter->magic = waiter;
INIT_LIST_HEAD(&waiter->list);
}
compiled as:
800554d0 <debug_mutex_lock_common>:
800554d0: e92d4008 push {r3, lr}
800554d4: e1a00001 mov r0, r1
800554d8: e3a02010 mov r2, #16 ; 0x10
800554dc: e3a01011 mov r1, #17 ; 0x11
800554e0: eb04426e bl 80165ea0 <memset>
800554e4: e1a03000 mov r3, r0
800554e8: e583000c str r0, [r3, #12]
800554ec: e5830000 str r0, [r3]
800554f0: e5830004 str r0, [r3, #4]
800554f4: e8bd8008 pop {r3, pc}
GCC assumes memset returns the value of pointer 'waiter' in register r0; causing
register/memory corruptions.
This patch fixes the return value of the assembly version of memset.
It adds a 'mov' instruction and merges an additional load+store into
existing load/store instructions.
For ease of review, here is a breakdown of the patch into 4 simple steps:
Step 1
======
Perform the following substitutions:
ip -> r8, then
r0 -> ip,
and insert 'mov ip, r0' as the first statement of the function.
At this point, we have a memset() implementation returning the proper result,
but corrupting r8 on some paths (the ones that were using ip).
Step 2
======
Make sure r8 is saved and restored when (! CALGN(1)+0) == 1:
save r8:
- str lr, [sp, #-4]!
+ stmfd sp!, {r8, lr}
and restore r8 on both exit paths:
- ldmeqfd sp!, {pc} @ Now <64 bytes to go.
+ ldmeqfd sp!, {r8, pc} @ Now <64 bytes to go.
(...)
tst r2, #16
stmneia ip!, {r1, r3, r8, lr}
- ldr lr, [sp], #4
+ ldmfd sp!, {r8, lr}
Step 3
======
Make sure r8 is saved and restored when (! CALGN(1)+0) == 0:
save r8:
- stmfd sp!, {r4-r7, lr}
+ stmfd sp!, {r4-r8, lr}
and restore r8 on both exit paths:
bgt 3b
- ldmeqfd sp!, {r4-r7, pc}
+ ldmeqfd sp!, {r4-r8, pc}
(...)
tst r2, #16
stmneia ip!, {r4-r7}
- ldmfd sp!, {r4-r7, lr}
+ ldmfd sp!, {r4-r8, lr}
Step 4
======
Rewrite register list "r4-r7, r8" as "r4-r8".
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Let the bus code process scm availability information and
notify scm device drivers about the new state.
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Stop writing to scm after certain error conditions such as a concurrent
firmware upgrade. Resume to normal state once scm_blk_set_available is
called (due to an scm availability notification).
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Extend the notify callback of scm_driver by an event parameter
to allow to distinguish between different notifications.
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the sentinel triggers, we do not want the boot loader authors to
just poke it and make the error go away, we want them to actually fix
the problem.
This should help avoid making the incorrect change in non-compliant
bootloaders.
[ hpa: dropped the Documentation/x86/boot.txt hunk pending
clarifications ]
Signed-off-by: Peter Jones <pjones@redhat.com>
Link: http://lkml.kernel.org/r/1362592823-28967-1-git-send-email-pjones@redhat.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
When boot_params->sentinel is set, all we really know is that some
undefined set of fields in struct boot_params contain garbage. In the
particular case of efi_info, however, there is a private magic for
that substructure, so it is generally safe to leave it even if the
bootloader is broken.
kexec (for which we did the initial analysis) did not initialize this
field, but of course all the EFI bootloaders do, and most EFI
bootloaders are broken in this respect (and should be fixed.)
Reported-by: Robin Holt <holt@sgi.com>
Link: http://lkml.kernel.org/r/CA%2B5PVA51-FT14p4CRYKbicykugVb=PiaEycdQ57CK2km_OQuRQ@mail.gmail.com
Tested-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Henrik reported that his MacAir 3.1 would not boot with
| commit 8d57470d8f
| Date: Fri Nov 16 19:38:58 2012 -0800
|
| x86, mm: setup page table in top-down
It turns out that we do not calculate the real_end properly:
We try to get 2M size with 4K alignment, and later will round down
to 2M, so we will get less then 2M for first mapping, in extreme
case could be only 4K only. In Henrik's system it has (1M-32K) as
last usable rage is [mem 0x7f9db000-0x7fef8fff].
The problem is exposed when EFI booting have several holes and it
will force mapping to use PTE instead as we only map usable areas.
To fix it, just make it be 2M aligned, so we can be guaranteed to be
able to use large pages to map it.
Reported-by: Henrik Rydberg <rydberg@euromail.se>
Bisected-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/CAE9FiQX4nQ7_1kg5RL_vh56rmcSHXUi1ExrZX7CwED4NGMnHfg@mail.gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The commit 27be457000
('x86 idle: remove 32-bit-only "no-hlt" parameter, hlt_works_ok
flag') removed the hlt_works_ok flag from struct cpuinfo_x86, but
boot_cpu_data and new_cpu_data initializers were not changed
causing setting f00f_bug flag, instead of fdiv_bug.
If CONFIG_X86_F00F_BUG is not set the f00f_bug flag is never
cleared.
To avoid such problems in future C99-style initialization is now
used.
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: len.brown@intel.com
Link: http://lkml.kernel.org/r/1362266082-2227-1-git-send-email-krzysiek@podlesie.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Commit 1fe42740 ("ARM: dts: mxs: Add the LCD to the 10049 board") seem
to have been applied with some fuzzyness, and the framebuffer
initialisation code for the CFA-10049 ended up in the CFA-10037
initialisation function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds #dma-cells property to PL330 DMA controller
nodes for supporting generic dma dt bindings on samsung exynos
platforms. #dma-channels and #dma-requests are not required now
but added in advance.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
WARNING: vmlinux.o(.text+0xfb80): Section mismatch in reference
from the function armpmu_register() to the function
.init.text:armpmu_init()
The function armpmu_register() references
the function __init armpmu_init().
This is often because armpmu_register lacks a __init
annotation or the annotation of armpmu_init is wrong.
Just drop the __init marking on armpmu_init() because
armpmu_register() no longer has an __init marking.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Before jumping to (position independent) C-code from the decompressor's
assembler world we set-up the C environment. This setup currently does not
set r9, which for arm-none-uclinux-uclibceabi toolchains is by default
expected to be the PIC offset base register (IE should point to the
beginning of the GOT).
Currently, therefore, in order to build working kernels that use the
decompressor it is necessary to use an arm-linux-gnueabi toolchain, or
similar. uClinux toolchains cause a prefetch abort to occur at the beginning
of the decompress_kernel function.
This patch allows uClinux toolchains to build bootable zImages by forcing
the -mno-single-pic-base option, which ensures that the location of the GOT
is re-derived each time it is required, and r9 becomes free for use as a
general purpose register.
This has a small (4% in instruction terms) advantage over the alternative of
setting r9 to point to the GOT before calling into the C-world.
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Somehow this select statement managed to squeeze itself between commit
0e152d8050 ("m68k: reorganize Kconfig
options to improve mmu/non-mmu selections") and commit
95e82747d6 ("m68k: drop unused Kconfig
symbols"). Whatever happened, there is no Kconfig symbol named EMAC_INC.
The select statement for that symbol is a nop. Drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The cpuinfo_x86 ptr is unused now. Drop it. Got obsolete by 69fb3676df
("x86 idle: remove mwait_idle() and "idle=mwait" cmdline param")
removing its only user.
[ hpa: fixes gcc warning ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1362428180-8865-2-git-send-email-bp@alien8.de
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Commit 51482be9 (ARM: OMAP: USB: Add phy binding information) forgot to
add phy binding for RX-51, and as a result USB does not work anymore on
3.9-rc1. Add the missing binding.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Our flush_tlb_kernel_range() implementation calls __tlb_flush_mm() with
&init_mm as argument. __tlb_flush_mm() however will only flush tlbs
for the passed in mm if its mm_cpumask is not empty.
For the init_mm however its mm_cpumask has never any bits set. Which in
turn means that our flush_tlb_kernel_range() implementation doesn't
work at all.
This can be easily verified with a vmalloc/vfree loop which allocates
a page, writes to it and then frees the page again. A crash will follow
almost instantly.
To fix this remove the cpumask_empty() check in __tlb_flush_mm() since
there shouldn't be too many mms with a zero mm_cpumask, besides the
init_mm of course.
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The size of the vmemmap must be a multiple of PAGES_PER_SECTION, since the
common code always initializes the vmemmap in such pieces.
So we must round up in order to not have a too small vmemmap.
Fixes an IPL crash on 31 bit with more than 1920MB.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current machine check code uses the registers stored by the machine
in the lowcore at __LC_GPREGS_SAVE_AREA as the registers of the interrupted
context. The registers 0-7 of a user process can get clobbered if a machine
checks interrupts the execution of a critical section in entry[64].S.
The reason is that the critical section cleanup code may need to modify
the PSW and the registers for the previous context to get to the end of a
critical section. If registers 0-7 have to be replaced the relevant copy
will be in the registers, which invalidates the copy in the lowcore. The
machine check handler needs to explicitly store registers 0-7 to the stack.
Cc: stable@vger.kernel.org
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We support DSCR (Data Stream Control Register) so we should make sure we set it
in the FSCR (Facility Status & Control Register) incase some firmwares don't
set it. If we don't set this, we'll take a facility unavailable exception when
using the DSCR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This sets the DSCR (Data Stream Control Register) in the FSCR (Facility Status
& Control Register).
Also harmonise TAR (Target Address Register) FSCR bit definition too.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we only set the FSCR (Facility Status and Control Register) when HV=1
but this feature is available when HV=0 also. This patch sets FSCR when HV=0.
Also, we currently only set the FSCR on the master CPU. This patch also sets
the FSCR on secondary CPUs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since kmp takes 2 unsigned long args there should be a compat wrapper.
Since one isn't provided I think it's safer just to hook this up to not
implemented. If we need it later we can do it properly then.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The BITOP_LE_SWIZZLE macro was used in the little-endian bitops functions
for powerpc. But these functions were converted to generic bitops and
the BITOP_LE_SWIZZLE is not used anymore.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we use the link register to branch up high in the early MMU on
syscall entry path. Unfortunately, this trashes the link stack as the
address we are going to is not associated with the earlier mflr.
This patch simply converts us to used the count register (volatile over
syscalls anyway) instead. This is much better at predicting in this
scenario and doesn't trash link stack causing a bunch of additional
branch mispredicts later. Benchmarking this on POWER8 saves a bunch of
cycles on Anton's null syscall benchmark here:
http://ozlabs.org/~anton/junkcode/null_syscall.c
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
the dest buf len is 80 (HVCS_CLC_LENGTH + 1).
the src buf len is PAGE_SIZE.
if src buf string len is more than 80, it will cause issue.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When building with CRYPTO_SHA1_PPC enabled we fail with:
powerpc/crypto/sha1-powerpc-asm.S: Assembler messages:
powerpc/crypto/sha1-powerpc-asm.S:116: Error: can't resolve `0' {*ABS* section} - `STACKFRAMESIZE' {*UND* section}
powerpc/crypto/sha1-powerpc-asm.S:116: Error: expression too complex
powerpc/crypto/sha1-powerpc-asm.S:178: Error: unsupported relocation against STACKFRAMESIZE
Use INT_FRAME_SIZE instead of STACKFRAMESIZE.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Tested-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the DMA controller clocks are managed at amba bus level, the
PL330 device clocks handling has been removed from the driver in
commit 7c71b8eb("DMA: PL330: Remove redundant runtime_suspend/
resume functions")
However, this left the S5PV210 platform with only clkdev entries
linking "apb_pclk" clock conn_id to a dummy clock, rather than
to corresponding platform PL330 DMAC clock.
As a result the DMA controller is now attempted to be used on
S5PV210 with the clock disabled and the driver fails with an
error:
dma-pl330 dma-pl330.0: PERIPH_ID 0x0, PCELL_ID 0x0 !
dma-pl330: probe of dma-pl330.0 failed with error -22
dma-pl330 dma-pl330.1: PERIPH_ID 0x0, PCELL_ID 0x0 !
dma-pl330: probe of dma-pl330.1 failed with error -22
Fix this by adding "apb_pclk" clkdev entries for the Peripheral
DMA controllers 0/1 and removing the dummy apb_pclk clock.
Reported-by: Lonsn <lonsn2005@gmail.com>
Tested-by: Lonsn <lonsn2005@gmail.com>
Cc: Inderpal Singh <inderpal.singh@linaro.org>
Cc: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: <stable@vger.kernel.org> # v3.7+
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
- A few sparse warning fixes
- Fix usb function regression caused by usb Kconfig option changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRNELIAAoJEFBXWFqHsHzOP/QH/jjE9MrvckPwb8h1I7R8a7yc
td3N5rikKiy2XN4snjIrPFaKi9JQ//I1oLvhsXNSD1uqWqqtRLg6lxzIdiheUJEd
NsAFLKTPMaJHJ/s3y0mLNRgyuBcyvDrF6jYJ8ncdGDCMAXBKifkTmrqqai2d0dZz
DiIiEW46PVhsQkoxdnLKw7xGScmXJpyqwshbi+zhAB17yE1FBLCCsZGD1jVr0v/y
Q6pnCjiJ8es9SAvmCvZ8cY1XxOxUMsCr2VhIy/QPF5HyuZPcRaV1nVGljfzo13J3
sPvBfmUZaY9ezqOVCUuYatQ3bAQ5f55KsLuGz+IHwMLHllXAML0Fw69/oDR86qs=
=JOus
-----END PGP SIGNATURE-----
Merge tag 'mxs-fixes-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
The mxs fixes for 3.9:
- A few sparse warning fixes
- Fix usb function regression caused by usb Kconfig option changes
* tag 'mxs-fixes-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: ocotp: Fix sparse warning
ARM: mxs: icoll: Fix sparse warning
ARM: mxs: mm: Fix sparse warning
ARM: mxs_defconfig: Make USB host functional again
Signed-off-by: Olof Johansson <olof@lixom.net>
- move early resume code out of .data section to fix allyesconfig
failure since c08e20d (arm: Add v7_invalidate_l1 to cache-v7.S)
gets merged
- Fix incorrect DISP1_DAT_21 number in imx53-mba53 disp1-grp1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRND3rAAoJEFBXWFqHsHzOL2cH/je/02JztrorpD2k76mQLjo4
2hjfUwpYNvwEpwBCXo5NnDv5I4XrkJdHs7O2CHmigQOpDYSvq9qx3VcPQ0BX8cWU
3Qqb9tiglNsvD2NuxUYmG2CHFpGLp+lK3unkA/ZDXM2apjbacL1/wTgU81uthDwY
SLBBS7hSlBvuPdxoeIBeuOOBYnhbdaZCutgFVTF8rRT6RHmYjekga6OqF32Vp/og
Gxw50cj+smdW6wr1Na0zQJfMHTkm5hJ9s9iYHAbYNZplpl8VZJQAaCWgZhihZJYI
XULUCR0s8DLLUgj4IUgJS3Kc35G/2M1ovhxyw3hqDzOt+Miy8m4eYh21BL2iS8w=
=V76T
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
The imx fixes for 3.9:
- move early resume code out of .data section to fix allyesconfig
failure since c08e20d (arm: Add v7_invalidate_l1 to cache-v7.S)
gets merged
- Fix incorrect DISP1_DAT_21 number in imx53-mba53 disp1-grp1
* tag 'imx-fixes-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx53-mba53: fix fsl,pins for disp1-grp1
ARM: mach-imx: move early resume code out of the .data section
Signed-off-by: Olof Johansson <olof@lixom.net>
As DT support for clocks and smp_twd is enabled, add clock entry
for smp_twd clock to DT.
This fixes the following error while booting the kernel:
smp_twd: clock not found -2
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: include kernel log spew that this fixes]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
commit 5f300acd8a
(ARM: 7152/1: distclean: Remove generated .dtb files)
ensured that dtbs were cleaned up when they were in
arch/arm/boot.
However, with the following commit:
commit 499cd82986
(ARM: dt: change .dtb build rules to build in dts directory)
make clean now leaves dtbs in arch/arm/boot/dts/
untouched. Include dts directory so that clean-files rule
from arch/arm/boot/dts/Makefile is invoked when make
clean is done.
Cc: Dirk Behme <dirk.behme@de.bosch.com>
CC: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
BCM2835-ARM-Peripherals.pdf states that the I2C module's input clock is
nominally 150MHz, and that value is currently reflected in bcm2835.dtsi.
However, practical measurements show that the rate is actually 250MHz,
and this agrees with various downstream kernels.
Switch the I2C clock's frequency to 250MHz so that the generated bus
clock rate is accurate.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit bbd707ac {ARM: omap2: use machine specific hook for late init}
accidentally added two declarations for omap4430_init_late().
Remove the duplicate declaration.
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is needed because the omap_mux_get_by_name()
function calls the _omap_mux_get_by_name subfunction
for each mux partition until needed mux is not found.
As a result, we get messages like
"Could not find signal XXX" for each partition
where this mux name does not exist.
This patch fixes wrong error message in
the _omap_mux_get_by_name() function moving it
to the omap_mux_get_by_name() one and as result
reduces noise in the kernel log.
My kernel log without this patch:
[...]
[ 0.221801] omap_mux_init: Add partition: #2: wkup, flags: 3
[ 0.222045] _omap_mux_get_by_name: Could not find signal fref_clk0_out.sys_drm_msecure
[ 0.222137] _omap_mux_get_by_name: Could not find signal sys_nirq
[ 0.222167] _omap_mux_get_by_name: Could not find signal sys_nirq
[ 0.225006] _omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx
[ 0.225006] _omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx
[ 0.270111] _omap_mux_get_by_name: Could not find signal fref_clk4_out.fref_clk4_out
[ 0.273406] twl: not initialized
[...]
My kernel log with this patch:
[...]
[ 0.221771] omap_mux_init: Add partition: #2: wkup, flags: 3
[ 0.222106] omap_mux_get_by_name: Could not find signal sys_nirq
[ 0.224945] omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx
[ 0.274536] twl: not initialized
[...]
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP's debugfs interface creates one file
for each signal in the mux table, such file
provides a read method but didn't provide
read permission. Fix it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We should not select drivers from kconfig as they should by default
be optional. Otherwise we'll be chasing broken dependencies forever:
warning: (MACH_OMAP_ZOOM2 && MACH_OMAP_ZOOM3 && MWAVE) selects SERIAL_8250
which has unmet direct dependencies (TTY && HAS_IOMEM && GENERIC_HARDIRQS)
Fix the issue by removing the selects for zoom and add them to
omap2plus_defconfig.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The .init_late callback for OMAP3 has been missing for DT
builds, which causes a lot of late PM initializations to
be missed in turn.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 6797b4fe (ARM: OMAP2+: Prevent potential crash if GPMC probe fails)
added code to ensure that GPMC chip-selects could not be requested until the
device probe was successful. The chip-selects should have been
unreserved at the end of the probe function, but the code to unreserve
them appears to have ended up in the gpmc_calc_timings() function and
hence, this is causing problems requesting chip-selects. Fix this merge
error by unreserving the chip-selects at the end of the probe, but
before we call the gpmc child probe functions (for device-tree) which
request a chip-select.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Philip Avinash <avinashphilip@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
[tony@atomide.com: updated description to add breaking commit id]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 16559ae4 (kgdb: remove #include <linux/serial_8250.h> from kgdb.h)
had a side effect of breaking omap1_defconfig build as some headers
were included indirectly:
arch/arm/mach-omap1/board-h2.c:249: error: ‘INT_KEYBOARD’ undeclared here (not in a function)
...
This worked earlier as linux/serial_8250.h included linux/serial_core.h,
via linux/serial_8250.h from linux/kgdb.h. Fix this by including the
necessary headers directly.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This was pointed out by Al Viro. Using the correct wrappers
properly does sign extension as necessary on syscall arguments.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Marek Szyprowski