If an audio interface is configured to use ASYNCCLK then update the
asynchronous sample rate rather than one of our primary sample rates.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
mx27pdk board also has a mc13783 codec.
Add support for it and do a run-time machine type check to perform the correct
audiomux settings.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we don't set IMX_AUDMUX_V2_PTCR_TCLKDIR in the AUDMUX PTCR
register (means Tx clock pin is input), we don't need to set
IMX_AUDMUX_V2_PTCR_TCSEL as well. Since both i.MX35, i.MX51 and
i.MX6 datasheet says "When Tx clock pin set as an input, the TCSEL
settings are ignored".
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow any BCLK which can be divided down to generate LRCLK, not just the
lowest possible BCLK to clock out the samples.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow the user to select which of the system clocks each AIF is referenced
to and constran the DAI to the set of frequencies which can be generated
from that clock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
They're the rates for the BCLK, not for the sample rate, so rename so that
we don't confuse ourselves.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch implements the spdif out driver for ST peripheral. This
peripheral implements IEC60958 standard
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The STA529 is a digital stereo class-D audio amplifier. It includes an
audio DSP, an ST proprietary high-efficiency class-D driver and CMOS
power output stage. It is intended for high-efficiency
digital-to-power-audio conversion for portable applications.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds missing register default values to cache.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds register and bit shift definitions in header file.
Changes are for TLV320AIC310x based on data sheet.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Leave it up to the machine driver to disable accessory detection if
desired, the common pattern is to have accessory detection be a wake
source.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since most new drivers are expected to use regmap and since frequently the
only thing we need to do in the CODEC probe function is configure the I/O
try to initialise the register I/O using regmap if the driver hasn't done
so after probe().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
dapm_set_path_status() sets connect incorrectly in the case max > 1 with invert.
In that case, the raw disconnect value should be max, which corresponds to the
userspace value 0.
This use case currently does not appear upstream, but it could break
SOC_DAPM_SINGLE() or SOC_DAPM_SINGLE_TLV() elsewhere or in the future.
This patch completes commit 3a9abe8.
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <alsa-devel@alsa-project.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the dmaengine based Tegra APB DMA driver for
data transfer between SPI fifo and memory in
place of legacy Tegra APB DMA.
Because generic soc-dmaengine-pcm uses the DMAs API
based on dmaengine, using the exported APIs provided
by this generic driver.
The new driver is selected if legacy driver is not
selected and new dma driver is enabled through config
file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stereo is not yet supported by dapm widgets, so remove stereo code from
snd_soc_dapm_get_volsw(), and warn if stereo controls are detected.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current method for machine driver to register with the ASoC core is to use
snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
From Shawn Guo <shawn.guo@linaro.org>, this makes it possible to use
sparse irqs with mach-imx.
* 'imx/sparse-irq' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: enable SPARSE_IRQ for imx platform
ARM: fiq: change FIQ_START to a variable
tty: serial: imx: remove the use of MXC_INTERNAL_IRQS
ARM: imx: remove unneeded mach/irq.h inclusion
i2c: imx: remove unneeded mach/irqs.h inclusion
ARM: imx: add a legacy irqdomain for mx31ads
ARM: imx: add a legacy irqdomain for 3ds_debugboard
ARM: imx: pass gpio than irq number into mxc_expio_init
ARM: imx: leave irq_base of wm8350_platform_data uninitialized
dma: ipu: remove the use of ipu_platform_data
ARM: imx: move irq_domain_add_legacy call into avic driver
ARM: imx: move irq_domain_add_legacy call into tzic driver
gpio/mxc: move irq_domain_add_legacy call into gpio driver
ARM: imx: eliminate macro IRQ_GPIOx()
ARM: imx: eliminate macro IOMUX_TO_IRQ()
ARM: imx: eliminate macro IMX_GPIO_TO_IRQ()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The mioa701 board code is converted to the snd_soc_register_card()
and snd_soc_unregister_card() APIs.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As all irqchips on imx have been changed to allocate their irq_descs,
and all unneeded mach/irqs.h inclusions on imx have been cleaned up,
now it's time to select SPARSE_IRQ for imx/mxc.
The SPARSE_IRQ support forces irqs allocation starting from 16. All
those static irq number definition for SoCs need to shift 16 to keep
non-DT boot works.
With all those static IRQ number and start definitions removed from
mach/irqs.h, the header becomes just a container of a couple of
mach-imx specific irq/fiq calls. Since mach/irqs.h is not included
by asm/irq.h now, the users of mxc_set_irq_fiq needs to explicitly
include mach/irqs.h themselves.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
In sound/soc/codecs/tlv320aic3x.c
data = snd_soc_read(codec, AIC3X_PLL_PROGA_REG);
snd_soc_write(codec, AIC3X_PLL_PROGA_REG,
data | (pll_p << PLLP_SHIFT));
In the above code, pll-p value is OR'ed with previous value without
clearing it. Bug is not seen if pll-p value doesn't change across
Sampling frequency.
However on some platforms (like AM335x EVM-SK), pll-p may have different
values across different sampling frequencies. In such case, above code
configures the pll with a wrong value.
Because of this bug, when a audio stream is played with pll value
different from previous stream, audio is heard as differently(like its
stretched).
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Without this very high BCLKs will be configured incorrectly.
Reported-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
snd_soc_dapm_put_volsw() sets connect incorrectly in the case max > 1 with
invert. In that case, the raw disconnect value should be max, which corresponds
to the userspace value 0.
This use case currently does not appear upstream, but it could break
SOC_DAPM_SINGLE() or SOC_DAPM_SINGLE_TLV() elsewhere or in the future.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise we fail to link when building as modules due to multiple
init/exit functions.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the support for spdif in audio codec.
Signed-off-by: vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It seems that the code duplication was added at a merge operation.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patches for stubbing out the generic clock API still haven't been
applied so we need to either add ifdefs here or add a dependency until
someone decides to actually apply them.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This gets the registers set up as early as possible, mainly useful for the
GPIOs to ensure that they're in the correct mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is only one caller and this allows us to cleanly leave the CODEC
with the internal LDO powered down which is the default state we're
looking for and means that we can robustly disable the register cache
only when we either disable the LDO or power down the external
regulators.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Get it done as early as possible, it's neater and minimises the time the
pins aren't configured as requested.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Even though the WM8904 is able to use idle_bias_off during both probe
and resume we were needlessly leaving the device in standby mode. Instead
power the device down as soon as we've confirmed that we can talk to it
and don't manage the bias level at all over suspend and resume, the core
will take us down to our minimum power level.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP53AxAAoJEHm+PkMAQRiGs2QH/RaqkXz96fwjhDcyiKpDqA3c
kGuS5mz5cOhnqKSmR88HFm6pwuhLux/qSJzeAmoQy1MC8a0ACx7AnANW0lfN3/qe
/HGYz8h60yCL/fhn8/bUYtdt9xsoDqoDcq/ooFl9mcsJGWbC6WeMSZU5dAUYqviE
qFrp5zjY07FG53CRGT0hFpezQNwNL+VLH30CF9LD+fJLPVEYum2zBNGXWM42rcw5
fxzGL/6SO8YqA/Upic1ht6HAd6s5LOrlST7qvnyXUMvRXN5z/Y92ueYJZefkS1Om
ohuLIKM2bv9/dJS67H8N2baSKGCzBdfSe5/5WaHdLYW9MiVju0wRl6HPJtAMrkk=
=H8t8
-----END PGP SIGNATURE-----
Merge tag 'v3.5-rc4' into for-3.6
Linux 3.5-rc4 contains some bug fixes which overlap with new features.
The WM5102 is a highly-integrated low-power audio system for smartphones,
tablets and other portable audio devices based on the Arizona platform.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Wolfson Arizona series of audio hub CODECs can share a large amount
of their driver code as the result of a common register map. This patch
adds some of this core support, providing a basis for the initial WM5102
audio driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We may as well print as many errors as we can in one go rather than
requiring developers to iterate through all their typos.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This patch implements the spdif IN driver for ST peripheral
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add support for the SPEAr ASoC pcm layer in ASoC
framework. The pcm layer uses common snd_dmaengine framework.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add support for synopsys I2S controller as per the ASoC
framework.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the sound dmaengine pcm helper functions implement the pcm_pointer
callback by trying to count the number of elapsed periods. This is done by
advancing the stream position in the dmaengine callback by one period.
Unfortunately there is no guarantee that the callback will be called for each
elapsed period. It may be possible that under high system load it is only called
once for multiple elapsed periods. This patch addresses the issue by
implementing support for querying the current stream position directly from the
dmaengine driver. Since not all dmaengine drivers support reporting the stream
position yet the old period counting implementation is kept for now.
Furthermore the new mechanism allows to report the stream position with a
sub-period granularity, given that the dmaengine driver supports this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the sound dmaengine pcm helper functions implement the pcm_pointer
callback by trying to count the number of elapsed periods. This is done by
advancing the stream position in the dmaengine callback by one period.
Unfortunately there is no guarantee that the callback will be called for each
elapsed period. It may be possible that under high system load it is only called
once for multiple elapsed periods. This patch renames the current implementation
and documents its shortcomings and that it should not be used anymore in new
drivers.
The next patch will introduce a new snd_dmaengine_pcm_pointer which will be
implemented based on querying the current stream position from the dma device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver enables i2s mode support on blackfin bf6xx platform.
We reuse bf5xx-i2s-pcm.c as its i2s pcm driver because it's the same
for both bf5xx and bf6xx soc.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The SPORT(Serial Port) module on bf6xx soc has a totally different ip
comparing to bf5xx soc. An individual SPORT module consists of two
independently configurable SPORT halves with identical functionality.
Each SPORT half can be configured for either transmitter or receiver.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch uses config() function to configure DMA
transmit options.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
There is a missing mutex_unlock() here. The cleanup path also has more
debug output.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add machine-driver for ST-Ericsson U8500 platform, including
support for the AB8500-codec.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
soc_probe_dai_link() currently inter-mixes the probing of CODECs,
platforms, and DAIs. This can lead to problems such as a CODEC's DAI
being probed before the CODEC, if that DAI is used as the CPU-side of
a DAI link without any other of the CODEC's DAIs having been used as
the CODEC-side of any DAI link that was probed earlier.
To solve this, split soc_probe_dai_link() into soc_probe_link_components()
and soc_probe_link_dais(). The former is used to probe all CODECs and
platforms used by a card first, and then the latter is used to probe all
the DAIs and links later.
A similar change is made to soc_remove_dai_links().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This change simply factors out part of soc_remove_dai_link() into a
standalone function. This makes platform and CODEC removal much more
similar at the call-sites.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When a standalone CPU DAI (one not part of a CODEC) is probed, widgets
are created for it. Add a call to snd_soc_dapm_free() in order to clean
these up when the CPU DAI is removed.
In order for snd_soc_dapm_free() to work, the CPU DAI's DAPM context's
list member must be initialized, since snd_soc_dapm_free() removes that
from the list it's part of. Add it to the card's list of DAPM contexts.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the CPU-side of a DAI link is a CODEC rather than a standalone DAI,
the codec initialization will call try_module_get() and create the DAI
widgets. Ensure that this isn't duplicated when the CPU DAI itself is
probed, if the CPU DAI is part of a CODEC.
Note that this is not a complete fix on its own, since there's no
guarantee that the CODEC itself will be initialized - currently that only
happens if the CODEC is also used as the CODEC-side of a DAI link, and
that initialization may happen before or after the DAIs within the CODEC
are initialized. However, such a scenario doesn't necessarily currently
work, and I don't think this change alone makes it any worse. This is
fixed in a couple patches time.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
add ttc-dkb machine support for pxa910. It uses 88pm8607 as codec
dai, mmp-pcm as platform and pxa-ssp as cpu dai.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds Alsa audio platform driver for mmp brownstone machine
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Leo Yan <leoy@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The SSPA is a configurable multi-channel audio serial (TDM) interface.
It's configurable at runtime to support up to 128 channels and the
number of bits per sample: 8, 12, 16, 20, 24 and 32 bits. It also
support stereo format: I2S, left-justified or right-justified.
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Leo Yan <leoy@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
mmp-pcm handle audio dma based on soc-dmaengine
Support mmp and pxa910
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Leo Yan <leoy@marvell.com>
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This fixes a leak if snd_soc_register_codec fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
GPLv2 -> GPL v2
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use clk_prepare/clk_unprepare as required by the generic clk framework.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If mic detect is left enabled and the WM8903 detects a status change,
the WM8903 driver will make a callback against the free()d jack, which
will cause a crash.
This problem can be triggered by fully initializing an audio card, then
removing and re-inserting the machine driver module.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also convert to use update_bits() while we're at it. No great need to do
this, it's just a bit neater to do as much as possible in the I2C probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
There's no reason to defer requesting of the interrupt until the CODEC
probe and doing so results in more work if we hit an error as we'll have
registered the CODEC with the core. It's neater to acquire as many of the
resources we'll need as we can in the bus probe function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
There's no urgent need for the interrupt handler to use the ASoC I/O
functions and it'll support a further move in where we request the
interrupt so call the regmap APIs directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Ensure that the device pins are configured as soon as possible by moving
the pin configration (including MICBIAS) into the I2C probe() function.
This had been done in the CODEC probe() function when we were relying on
the ASoC register I/O code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
The Tegra ASoC machine drivers only depend on Tegra architecture support
to compile, not specific board support. Remove Kconfig dependencies on
any particular board. This is required since Kconfig options for boards
are going away given the migration to device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Dialog DA732x audio codecs.
Signed-off-by: Michal Hajduk <Michal.Hajduk@diasemi.com>
Signed-off-by: Adam Thomson <Adam.Thomson@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
They aren't marked as readable and the feature is never used so they'll
never get referenced.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we don't have control over the LDO but do have control over the other
regulators then we may end up trying to write to a powered off device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're using demv_regulator_bulk_get() so don't need to manually free and
this is in the CODEC driver not the I2C driver anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add codec-driver for ST-Ericsson AB8500 mixed-signal ASIC.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We should be using the regmap API consistently for all the cache only
configuration and we should be going cache only before we power down
the supplies.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We no longer have a flat ASoC cache so can't peer directly into the array
any more but should instead use the register I/O functions to update the
cache.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org (v3.4)
pxa-ssp.c uses API like cpu_is_pxa3xx(), cpu_is_pxa2xx(), which is
defined under arch-pxa architecture, and drivers under mach-mmp
can't find it. so just use ssp->type to replace that API.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows the module to automatically load when instantiated from
device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stop open-coding the caching of the ctrl registers; instead, use
regmap_update_bits() to update parts of the register from different
places. The removal of the open-coded cache will allow controls to be
created which touch registers, which will be necessary if any of these
modules are converted to CODECs.
Get rid of tegra*_read/write; just call regmap_read/write directly.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the actual device of the I2S or SPDIF controller reporting the
problem. If a future change converts these controllers to be CODECs, then
there may be no pcm associated with the substream, so this change avoids
a crash.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
rtd->codec_dai->codec can be used instead.
This is a slight step along the way to not needing the rtd->codec field
any more.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Define the DAI format statically in the dai_link, rather than executing
code to set it each time the hw params are set.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is certainly required if the I2S and SPDIF controllers are converted
to be CODECs, and is probably good practice irrespective.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than having varying timeouts depending on the transition always
use a 4s timeout. This provides better diagnostics for clocking errors
and ensures compatibility with current calibration firmwares.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We should set "isabelle_regmap" before using it. GCC complains.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We should only add source widgets to the input list.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure that the dpcm_get_be() only returns BE DAI links.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Volume updates may not be acted upon if there is no clock applied when
the volume update is written. Ensure this doesn't happen by writing out
registers with volume updates after we enable each of the clocks.
There are more registers updated than before as previously we were
relying on wm_hubs to set those for controls it manages.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Ensure that all the actions get taken at appropriate times by calling the
_PRE and _POST events for the aifNclk_ev functions explicitly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Mark Brown