This driver assumes that an interrupt line is always available for
the I2C master. This is not always the case and this patch adds support
for a polling version.
Report from Andrew Lunn:
I did some timing tests for this. On my box, we request a udelay of
80uS. The kernel actually delays for about 79uS. We then spin in
ocores_wait() for an additional 10-11uS, which is 3 to 4 iterations.
There are actually 9 bits on the wire, not 8, since there is an
ACK/NACK bit after the actual data transfer. So i changed the delay to
(9 * 1000) / i2c->bus_clock_khz. That resulted in ocores_wait() mostly
not looping at all. But for reading an 4K AT24 EEPROM, it increased
the read time by 10ms, from 424ms to 434ms. So we should probably keep
with 8.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the Interrupt Flag (IF) is not set, we should not handle the IRQ:
- the line can be shared with other devices
- it can be a spurious interrupt
To avoid reading twice the status register, the ocores_process() function
expects it to be read by the caller.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Detecting a timeout is ok, but we also need to assert a STOP command on
the bus in order to prevent it from generating interrupts when there are
no on going transfers.
Example: very long transmission.
1. ocores_xfer: START a transfer
2. ocores_isr : handle byte by byte the transfer
3. ocores_xfer: goes in timeout [[bugfix here]]
4. ocores_xfer: return to I2C subsystem and to the I2C driver
5. I2C driver : it may clean up the i2c_msg memory
6. ocores_isr : receives another interrupt (pending bytes to be
transferred) but the i2c_msg memory is invalid now
So, since the transfer was too long, we have to detect the timeout and
STOP the transfer.
Another point is that we have a critical region here. When handling the
timeout condition we may have a running IRQ handler. For this reason I
introduce a spinlock.
In order to make easier to understan locking I have:
- added a new function to handle timeout
- modified the current ocores_process() function in order to be protected
by the new spinlock
Like this it is obvious at first sight that this locking serializes
the execution of ocores_process() and ocores_process_timeout()
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The old @sunsite.dk address is no longer active, so update the references.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
- mainly feature additions to drivers (stm32f7, qup, xlp9xx, mlxcpld, ...)
- conversion to use the i2c_8bit_addr_from_msg macro consistently
- move includes to platform_data
- core updates to allow the (still in review) I3C subsystem to connect
- and the regular share of smaller driver updates
* 'i2c/for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (68 commits)
i2c: qup: fix building without CONFIG_ACPI
i2c: tegra: Remove suspend-resume
i2c: imx-lpi2c: Switch to SPDX identifier
i2c: mxs: Switch to SPDX identifier
i2c: busses: make use of i2c_8bit_addr_from_msg
i2c: algos: make use of i2c_8bit_addr_from_msg
i2c: rcar: document R8A77980 bindings
i2c: qup: Add command-line parameter to override SCL frequency
i2c: qup: Correct duty cycle for FM and FM+
i2c: qup: Add support for Fast Mode Plus
i2c: qup: add probe path for Centriq ACPI devices
i2c: robotfuzz-osif: drop pointless test
i2c: robotfuzz-osif: remove pointless local variable
i2c: rk3x: Don't print visible virtual mapping MMIO address
i2c: opal: don't check number of messages in the driver
i2c: ibm_iic: don't check number of messages in the driver
i2c: imx: Switch to SPDX identifier
i2c: mux: pca954x: merge calls to of_match_device and of_device_get_match_data
i2c: mux: demux-pinctrl: use proper parent device for demux adapter
i2c: mux: improve error message for failed symlink
...
Because it looks neater.
For diolan, this allows factoring out some code that is now common
between if and else.
For eg20t, pch_i2c_writebytes is always called with a write in
msgs->flags, and pch_i2c_readbytes with a read.
For imx, i2c_imx_dma_write and i2c_imx_write are always called with a
write in msgs->flags, and i2c_imx_read with a read.
For qup, qup_i2c_write_tx_fifo_v1 is always called with a write in
qup->msg->flags.
For stu300, also restructure debug output for resends, since that
code as a result is only handling debug output.
Reviewed-by: Guenter Roeck <linux@roeck-us.net> [diolan]
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> [efm32 and imx]
Acked-by: Linus Walleij <linus.walleij@linaro.org> [stu300]
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The URL is broken. This patch fixes it.
Signed-off-by: Federico Vaga <federico.vaga@vaga.pv.it>
[wsa: shortened the URL a bit]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Make these const as they are only used in a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
clk_disable_unprepare() is missed on failure paths in ocores_i2c_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This allows using OpenCores I2C controller attached to its host in
native-endian mode with bi-endian CPUs. Example of such system is Xtensa
XTFPGA platform.
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For, !HAVE_CLK the clk API returns a NULL cookie. Rework the
initialization code to handle that. If clk_get_rate() delivers 0, we use
the fallback mechanisms. The patch is pretty easy when ignoring white
space issues (git diff -b).
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Allow bus clock specification as a common clock handle. This makes this
controller easier to use in a setup based on common clock framework.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
clock-frequency property is meant to control the bus frequency for i2c bus
drivers, but it was incorrectly used to specify i2c controller input clock
frequency.
Introduce new attribute, opencores,ip-clock-frequency, that specifies i2c
controller clock frequency and make clock-frequency attribute compatible
with other i2c drivers. Maintain backwards compatibility in case
opencores,ip-clock-frequency attribute is missing.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
While we are here, remove the indentation for the array setup because
such things always break after some time.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C of helpers used to live in of_i2c.c but experience (from SPI) shows
that it is much cleaner to have this in the core. This also removes a
circular dependency between the helpers and the core, and so we can
finally register child nodes in the core instead of doing this manually
in each driver. So, fix the drivers and documentation, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/i2c/busses/i2c-ocores.c:460:12: warning: 'ocores_i2c_suspend' defined but not used [-Wunused-function]
drivers/i2c/busses/i2c-ocores.c:471:12: warning: 'ocores_i2c_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Highlights:
- new drivers for Intel ismt & Broadcom bcm2835
- a number of drivers got support for more variants and mostly got
cleaned up on the way (sis630, i801, at91, tegra, designware)
- i2c got rid of all *_set_drvdata(..., NULL) on remove/probe failure
- removed the i2c_smbus_process_call from the core since there are no
users
- mxs can now switch between PIO and DMA depending on the message
size and the bus speed can now be arbitrary
In addition, there is the usual bunch of fixes, cleanups, devm_*
conversions, etc"
Fixed conflict (and buggy devm_* conversion) in i2c-s3c2410.c
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (39 commits)
i2c: Remove unneeded xxx_set_drvdata(..., NULL) calls
i2c: pxa: remove incorrect __exit annotations
i2c: ocores: Fix pointer to integer cast warning
i2c: tegra: remove warning dump if timeout happen in transfer
i2c: fix i2c-ismt.c printk format warning
i2c: i801: Add Device IDs for Intel Wellsburg PCH
i2c: add bcm2835 driver
i2c: ismt: Add Seth and Myself as maintainers
i2c: sis630: checkpatch cleanup
i2c: sis630: display unsigned hex
i2c: sis630: use hex to constants for SMBus commands
i2c: sis630: fix behavior after collision
i2c: sis630: clear sticky bits
i2c: sis630: Add SIS964 support
i2c: isch: Add module parameter for backbone clock rate if divider is unset
i2c: at91: fix unsed variable warning when building with !CONFIG_OF
i2c: Adding support for Intel iSMT SMBus 2.0 host controller
i2c: sh_mobile: don't send a stop condition by default inside transfers
i2c: sh_mobile: eliminate an open-coded "goto" loop
i2c: sh_mobile: fix timeout error handling
...
There is simply no reason to be manually setting the private driver
data to NULL in the remove/fail to probe cases. This is just extra
cruft code that can be removed.
A few notes:
* Nothing relies on drvdata being set to NULL.
* The __device_release_driver() function eventually calls
dev_set_drvdata(dev, NULL) anyway, so there's no need to do it
twice.
* I verified that there were no cases where xxx_get_drvdata() was
being called in these drivers and checking for / relying on the NULL
return value.
This could be cleaned up kernel-wide but for now just take the baby
step and remove from the i2c subsystem.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
After commit a000b8c1 [i2c: ocores: Add support for the GRLIB port of the
controller and use function pointers for getreg and setreg function],
compiling i2c-ocores.c for 64-bit gives the following warning:
drivers/i2c/busses/i2c-ocores.c: In function 'ocores_i2c_of_probe':
drivers/i2c/busses/i2c-ocores.c:334:15: warning: cast from pointer to integer of different size
Fix it by casting the pointer to long.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com> (for ocores and mux-gpio)
Acked-by: Havard Skinnemoen <hskinnemoen@gmail.com> (for i2c-gpio)
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> (for puf3)
Acked-by: Barry Song <baohua.song@csr.com> (for sirf)
Reviewed-by: Jean Delvare <khali@linux-fr.org>
[wsa: Fixed "foo* bar" flaws while we are here]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Pull i2c-embedded changes from Wolfram Sang:
- CBUS driver (an I2C variant)
- continued rework of the omap driver
- s3c2410 gets lots of fixes and gains pinctrl support
- at91 gains DMA support
- the GPIO muxer gains devicetree probing
- typical fixes and additions all over
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (45 commits)
i2c: omap: Remove the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE flag
i2c: at91: add dma support
i2c: at91: change struct members indentation
i2c: at91: fix compilation warning
i2c: mxs: Do not disable the I2C SMBus quick mode
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Remove recently introduced performance overheads
i2c: ocores: Move grlib set/get functions into #ifdef CONFIG_OF block
i2c: s3c2410: Add fix for i2c suspend/resume
i2c: s3c2410: Fix code to free gpios
i2c: i2c-cbus-gpio: introduce driver
i2c: ocores: Add support for the GRLIB port of the controller and use function pointers for getreg and setreg functions
i2c: ocores: Add irq support for sparc
i2c: omap: Move the remove constraint
ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
i2c: s3c2410: do not special case HDMIPHY stuck bus detection
i2c: s3c2410: use exponential back off while polling for bus idle
i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
i2c: s3c2410: grab adapter lock while changing i2c clock
i2c: s3c2410: Add support for pinctrl
...
This moves the grlib set and get functions into the #ifdef CONFIG_OF block to
avoid warnings of unimplemented functions when compiling with -Wunused-function
when CONFIG_OF is not defined.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The registers in the GRLIB port of the controller are 32-bit and in big endian
byte order. The PRELOW and PREHIGH registers are merged into one register. The
subsequent registers have their offset decreased accordingly. Hence the register
access needs to be handled in a non-standard manner using custom getreg and
setreg functions.
Add setreg and getreg functions for different register widths and let oc_setreg
and oc_getreg use function pointers to call the appropriate functions.
A type is added as the data of the of match table entries. A new entry with a
different compatible string is added to the table. The type of that entry
triggers usage of the custom grlib functions by setting the setreg and getreg
function pointers.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Add sparc support by using platform_get_irq instead of platform_get_resource.
There are no platform resources of type IORESOURCE_IRQ for sparc, but
platform_get_irq works for sparc. In the non-sparc case platform_get_irq
internally uses platform_get_resource.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Filenames of devictree binding documentation seems to be arbitrary and
for me it is unneeded hazzle to find the corresponding documentation for
a specific driver.
Naming the description the same as the driver is a lot easier and makes
sense to me since the driver defines the binding it understands.
Also, remove a reference in one source to the binding documentation, since path
information easily gets stale.
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Replacing the devm_request_mem_region() and devm_ioremap_nocache() calls
by a single call to devm_request_and_ioremap() simplifies the code.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Some architectures supports only 16-bit or 32-bit read/write access to
their IO space. Add a 'reg-io-width' platform and OF parameter which
specifies the IO width to support these platforms.
reg-io-width can be specified as 1, 2 or 4, and has a default value
of 1 if it is unspecified.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Deprecate 'regstep' property and use the standard 'reg-shift' property
for register offset shifts. 'regstep' will still be supported as an
optional property, but will give a warning when used.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cleanups to i2c-cores, no change in logic, changes are:
* Move i2c-ocores device tree documentation from source file to
Documentation/devicetree/bindings/i2c/i2c-ocores.txt.
* Add \n to dev_warn and dev_err messages where missing
* Minor updates to the text and formatting fixes.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Make the OpenCores I2C controller driver define its PM callbacks
through a struct dev_pm_ops object rather than by using legacy PM
hooks in struct platform_driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Call of_i2c_register_devices() in probe function to register i2c devices
specified in the device tree or OF.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
[wsa: add proper braces]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Convert the drivers in drivers/i2c/busses/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Yong Zhang <yong.zhang0@gmail.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Note that the mfd's platform_data is marked __devinitdata. This
is still correct in all cases except for the timbgpio driver, whose
remove hook has been changed to no longer reference the pdata.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
x86: Clean up apic.c and apic.h
x86: Remove superflous goal definition of tsc_sync
x86: dt: Correct local apic documentation in device tree bindings
x86: dt: Cleanup local apic setup
x86: dt: Fix OLPC=y/INTEL_CE=n build
rtc: cmos: Add OF bindings
x86: ce4100: Use OF to setup devices
x86: ioapic: Add OF bindings for IO_APIC
x86: dtb: Add generic bus probe
x86: dtb: Add support for PCI devices backed by dtb nodes
x86: dtb: Add device tree support for HPET
x86: dtb: Add early parsing of IO_APIC
x86: dtb: Add irq domain abstraction
x86: dtb: Add a device tree for CE4100
x86: Add device tree support
x86: e820: Remove conditional early mapping in parse_e820_ext
x86: OLPC: Make OLPC=n build again
x86: OLPC: Remove extra OLPC_OPENFIRMWARE_DT indirection
x86: OLPC: Cleanup config maze completely
x86: OLPC: Hide OLPC_OPENFIRMWARE config switch
...
Fix up conflicts in arch/x86/platform/ce4100/ce4100.c
ocores_i2c_of_probe needs to use a const __be32 type for handing
device tree property values. This patch fixed the following build
warning:
CC drivers/i2c/busses/i2c-ocores.o
drivers/i2c/busses/i2c-ocores.c: In function 'ocores_i2c_of_probe':
drivers/i2c/busses/i2c-ocores.c:254: warning: assignment discards qualifiers from pointer target type
drivers/i2c/busses/i2c-ocores.c:261: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Having conditional around the of_match_table and the of_node pointers
turns out to make driver code use ugly #ifdef blocks. Drop the
conditionals and remove the #ifdef blocks from the affected drivers.
Also tidy up minor whitespace issues within the same hunks.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
This puts some documentation for the device tree configuration at the head
of the driver file. Hopefully this can get moved to a common area for this
type of documentation at a later date; unfortunately, there isn't really
such a place in the kernel tree at this time.
Furthermore, the regstep and clock-frequency parameters are really bus
parameters and should probably be passed to the driver in a better way.
Consider that a TODO.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch converts the i2c-cores driver to use devres routines for
resource allocation.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adapts the i2c-ocores driver for being defined and configured via
a device tree description.
The device tree bits need to be protected by CONFIG_OF guards as this is
still an optional feature.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Federico Vaga