IORESOURCE_ROM_SHADOW means there is a copy of a device's option ROM in
RAM. The existence of such a copy and its location are arch-specific.
Previously the IORESOURCE_ROM_SHADOW flag was set in arch code, but the
0xC0000-0xDFFFF location was hard-coded into the PCI core.
If we're using a shadow copy in RAM, disable the ROM BAR and release the
address space it was consuming. Move the location information from the PCI
core to the arch code that sets IORESOURCE_ROM_SHADOW. Save the location
of the RAM copy in the struct resource for PCI_ROM_RESOURCE.
After this change, pci_map_rom() will call pci_assign_resource() and
pci_enable_rom() for these IORESOURCE_ROM_SHADOW resources, which we did
not do before. This is safe because:
- pci_assign_resource() will do nothing because the resource is marked
IORESOURCE_PCI_FIXED, which means we can't move it, and
- pci_enable_rom() will not turn on the ROM BAR's enable bit because the
resource is marked IORESOURCE_ROM_SHADOW, which means it is in RAM
rather than in PCI memory space.
Storing the location in the struct resource means "lspci" will show the
shadow location, not the value from the ROM BAR.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A shadow copy of an option ROM is placed by the BIOS as a fixed address.
Set IORESOURCE_PCI_FIXED to indicate that we can't move the shadow copy.
This prevents warnings like the following when we assign resources:
BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
This warning is emitted by pdev_sort_resources(), which already ignores
IORESOURCE_PCI_FIXED resources.
Link: http://lkml.kernel.org/r/CA+55aFyVMfTBB0oz_yx8+eQOEJnzGtCsYSj9QuhEpdZ9BHdq5A@mail.gmail.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use common interface to simplify PCI host bridge implementation.
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use common struct resource_entry to replace private
struct iospace_resource.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use common ACPI resource parsing interface to parse ACPI resources for
PCI host bridge, so we could share more code between IA64 and x86.
Later we will consolidate arch specific implementations into ACPI core.
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert dff22d2054 ("PCI: Call pci_read_bridge_bases() from core instead
of arch code").
Reading PCI bridge windows is not arch-specific in itself, but there is PCI
core code that doesn't work correctly if we read them too early. For
example, Hannes found this case on an ARM Freescale i.mx6 board:
pci_bus 0000:00: root bus resource [mem 0x01000000-0x01efffff]
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0000:00:00.0: BAR 8: no space for [mem size 0x01000000] (mem window)
pci 0000:01:00.0: BAR 2: failed to assign [mem size 0x00200000]
pci 0000:01:00.0: BAR 1: failed to assign [mem size 0x00004000]
pci 0000:01:00.0: BAR 0: failed to assign [mem size 0x00000100]
The 00:00.0 mem window needs to be at least 3MB: the 01:00.0 device needs
0x204100 of space, and mem windows are megabyte-aligned.
Bus sizing can increase a bridge window size, but never *decrease* it (see
d65245c329 ("PCI: don't shrink bridge resources")). Prior to
dff22d2054, ARM didn't read bridge windows at all, so the "original size"
was zero, and we assigned a 3MB window.
After dff22d2054, we read the bridge windows before sizing the bus. The
firmware programmed a 16MB window (size 0x01000000) in 00:00.0, and since
we never decrease the size, we kept 16MB even though we only needed 3MB.
But 16MB doesn't fit in the host bridge aperture, so we failed to assign
space for the window and the downstream devices.
I think this is a defect in the PCI core: we shouldn't rely on the firmware
to assign sensible windows.
Ray reported a similar problem, also on ARM, with Broadcom iProc.
Issues like this are too hard to fix right now, so revert dff22d2054.
Reported-by: Hannes <oe5hpm@gmail.com>
Reported-by: Ray Jui <rjui@broadcom.com>
Link: http://lkml.kernel.org/r/CAAa04yFQEUJm7Jj1qMT57-LG7ZGtnhNDBe=PpSRa70Mj+XhW-A@mail.gmail.com
Link: http://lkml.kernel.org/r/55F75BB8.4070405@broadcom.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
When we scan a PCI bus, we read PCI-PCI bridge window registers with
pci_read_bridge_bases() so we can validate the resource hierarchy. Most
architectures call pci_read_bridge_bases() from pcibios_fixup_bus(), but
PCI-PCI bridges are not arch-specific, so this doesn't need to be in
arch-specific code.
Call pci_read_bridge_bases() directly from the PCI core instead of from
arch code.
For alpha and mips, we now call pci_read_bridge_bases() always; previously
we only called it if PCI_PROBE_ONLY was set.
[bhelgaas: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: James E.J. Bottomley <jejb@parisc-linux.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: David Howells <dhowells@redhat.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Tony Luck <tony.luck@intel.com>
CC: David S. Miller <davem@davemloft.net>
CC: Ingo Molnar <mingo@redhat.com>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Michal Simek <monstr@monstr.eu>
CC: Chris Zankel <chris@zankel.net>
Commit 97badf873a (device property: Make it possible to use
secondary firmware nodes) uncovered a bug in the x86 (and ia64) PCI
host bridge initialization code that assumes bridge->bus->sysdata
to always point to a struct pci_sysdata object which need not be
the case (in particular, the Xen PCI frontend driver sets it to point
to a different data type). If it is not the case, an incorrect
pointer (or a piece of data that is not a pointer at all) will be
passed to ACPI_COMPANION_SET() and that may cause interesting
breakage to happen going forward.
To work around this problem use the observation that the ACPI
host bridge initialization always passes NULL as parent to
pci_create_root_bus(), so if pcibios_root_bridge_prepare() sees
a non-NULL parent of the bridge, it should not attempt to set
an ACPI companion for it, because that means that
pci_create_root_bus() has been called by someone else.
Fixes: 97badf873a (device property: Make it possible to use secondary firmware nodes)
Reported-and-tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Prior to c770cb4cb5 ("PCI: Mark invalid BARs as unassigned"), if we tried
to claim a PCI BAR but could not find an upstream bridge window that
matched it, we complained but still allowed the device to be enabled.
c770cb4cb5 broke devices that previously worked (mptsas and igb in the
case Tony reported, but it could be any devices) because it marks those
BARs as IORESOURCE_UNSET, which makes pci_enable_device() complain and
return failure:
igb 0000:81:00.0: can't enable device: BAR 0 [mem size 0x00020000] not assigned
igb: probe of 0000:81:00.0 failed with error -22
The underlying cause is an ACPI Address Space Descriptor for a PCI host
bridge window that is marked as "consumer". This is a firmware defect:
resources that are produced on the downstream side of a bridge should be
marked "producer". But rejecting these BARs that we previously allowed is
a functionality regression, and firmware has not used the producer/consumer
bit consistently, so we can't rely on it anyway.
Stop checking the producer/consumer bit, and assume all bridge Address
Space Descriptors are for bridge windows.
Note that this change does not affect I/O Port or Fixed Location I/O Port
Descriptors, which are commonly used for the [io 0x0cf8-0x0cff] config
access range. That range is a "consumer" range and should not be treated
as a window.
Fixes: c770cb4cb5 ("PCI: Mark invalid BARs as unassigned")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=96961
Reported-and-tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpica:
ACPICA: Events: Enable APIs to allow interrupt/polling adaptive request based GPE handling model
ACPICA: Events: Introduce acpi_set_gpe()/acpi_finish_gpe() to reduce divergences
ACPICA: Events: Introduce ACPI_GPE_DISPATCH_RAW_HANDLER to fix 2 issues for the current GPE APIs
ACPICA: Update version to 20150204
ACPICA: Update Copyright headers to 2015
ACPICA: Hardware: Cast GPE enable_mask before storing
ACPICA: Events: Cleanup GPE dispatcher type obtaining code
ACPICA: Events: Cleanup to move acpi_gbl_global_event_handler invocation out of acpi_ev_gpe_dispatch()
ACPICA: Events: Cleanup of resetting the GPE handler to NULL before removing
ACPICA: Events: Fix uninitialized variable
ACPICA: Events: Remove acpi_ev_valid_gpe_event() due to current restriction
ACPICA: Events: Remove duplicated sanity check in acpi_ev_enable_gpe()
ACPICA: Events: Back port "ACPICA: Save current masks of enabled GPEs after enable register writes"
ACPICA: Resources: Provide common part for struct acpi_resource_address structures.
ACPI: Introduce acpi_unload_parent_table() usages in Linux kernel
ACPICA: take ACPI_MTX_INTERPRETER in acpi_unload_table_id()
struct acpi_resource_address and struct acpi_resource_extended_address64 share substracts
just at different offsets. To unify the parsing functions, OSPMs like Linux
need a new ACPI_ADDRESS64_ATTRIBUTE as their substructs, so they can
extract the shared data.
This patch also synchronizes the structure changes to the Linux kernel.
The usages are searched by matching the following keywords:
1. acpi_resource_address
2. acpi_resource_extended_address
3. ACPI_RESOURCE_TYPE_ADDRESS
4. ACPI_RESOURCE_TYPE_EXTENDED_ADDRESS
And we found and fixed the usages in the following files:
arch/ia64/kernel/acpi-ext.c
arch/ia64/pci/pci.c
arch/x86/pci/acpi.c
arch/x86/pci/mmconfig-shared.c
drivers/xen/xen-acpi-memhotplug.c
drivers/acpi/acpi_memhotplug.c
drivers/acpi/pci_root.c
drivers/acpi/resource.c
drivers/char/hpet.c
drivers/pnp/pnpacpi/rsparser.c
drivers/hv/vmbus_drv.c
Build tests are passed with defconfig/allnoconfig/allyesconfig and
defconfig+CONFIG_ACPI=n.
Original-by: Thomas Gleixner <tglx@linutronix.de>
Original-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Every PCI-PCI bridge window should fit inside an upstream bridge window
because orphaned address space is unreachable from the primary side of the
upstream bridge. If we inherit invalid bridge windows that overlap an
upstream window from firmware, clip them to fit and update the bridge
accordingly.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Tony Luck <tony.luck@intel.com>
CC: Fenghua Yu <fenghua.yu@intel.com>
CC: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
CC: linux-ia64@vger.kernel.org
Commit 20cde69402 ("x86, ia64: Move EFI_FB vga_default_device()
initialization to pci_vga_fixup()") moved boot video device detection from
efifb to x86 and ia64 pci/fixup.c.
For dual-GPU Apple computers above change represents a regression as code
in efifb did forcefully override vga_default_device while the merge did not
(vgaarb happens prior to PCI fixup).
To improve on initial device selection by vgaarb (it cannot know if PCI
device not behind bridges see/decode legacy VGA I/O or not), move the
screen_info based check from pci_video_fixup() to vgaarb's init function and
use it to refine/override decision taken while adding the individual PCI
VGA devices. This way PCI fixup has no reason to adjust vga_default_device
anymore but can depend on its value for flagging shadowed VBIOS.
This has the nice benefit of removing duplicated code but does introduce a
#if defined() block in vgaarb. Not all architectures have screen_info and
would cause compile to fail without it.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=84461
Reported-and-Tested-By: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Matthew Garrett <matthew.garrett@nebula.com>
CC: stable@vger.kernel.org # v3.5+
Commit b4aa016305 ("efifb: Implement vga_default_device() (v2)") added
efifb vga_default_device() so EFI systems that do not load shadow VBIOS or
setup VGA get proper value for boot_vga PCI sysfs attribute on the
corresponding PCI device.
Xorg doesn't detect devices when boot_vga=0, e.g., on some EFI systems such
as MacBookAir2,1. Xorg detects the GPU and finds the DRI device but then
bails out with "no devices detected".
Note: When vga_default_device() is set boot_vga PCI sysfs attribute
reflects its state. When unset this attribute is 1 whenever
IORESOURCE_ROM_SHADOW flag is set.
With introduction of sysfb/simplefb/simpledrm efifb is getting obsolete
while having native drivers for the GPU also makes selecting sysfb/efifb
optional.
Remove the efifb implementation of vga_default_device() and initialize
vgaarb's vga_default_device() with the PCI GPU that matches boot
screen_info in pci_fixup_video().
[bhelgaas: remove unused "dev" in efifb_setup()]
Fixes: b4aa016305 ("efifb: Implement vga_default_device() (v2)")
Tested-by: Anibal Francisco Martinez Cortina <linuxkid.zeuz@gmail.com>
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Matthew Garrett <matthew.garrett@nebula.com>
CC: stable@vger.kernel.org # v3.5+
Use pci_is_bridge() to simplify code. No functional change.
Requires: 326c1cdae7 PCI: Rename pci_is_bridge() to pci_has_subordinate()
Requires: 1c86438c94 PCI: Add new pci_is_bridge() interface
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/misc:
PCI: Enable INTx if BIOS left them disabled
ia64/PCI: Set IORESOURCE_ROM_SHADOW only for the default VGA device
x86/PCI: Set IORESOURCE_ROM_SHADOW only for the default VGA device
PCI: Update outdated comment for pcibios_bus_report_status()
PCI: Cleanup per-arch list of object files
PCI: cpqphp: Fix hex vs decimal typo in cpqhpc_probe()
x86/PCI: Fix function definition whitespace
x86/PCI: Reword comments
x86/PCI: Remove unnecessary local variable initialization
PCI: Remove unnecessary list_empty(&pci_pme_list) check
Setting the IORESOURCE_ROM_SHADOW flag on a VGA card other than the primary
prevents it from reading its own ROM. It will get the content of the
shadow ROM at C000 instead, which is of the primary VGA card and the driver
of the secondary card will bail out.
Fix this by checking if the arch code or vga-arbitration has already
determined the vga_default_device, if so only apply the fix to this primary
video device and let the comment reflect this.
[bhelgaas: add subject, split x86 & ia64 into separate patches,
include vgaarb.h]
Signed-off-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The IOMMU, LSAPIC, IOSAPIC, and PCI host bridge code doesn't care about
_PXM values directly; it only needs to know what NUMA node the hardware is
on.
This uses acpi_get_node() directly and removes the _PXM stuff.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify struct acpi_dev_node to contain a pointer to struct acpi_device
associated with the given device object (that is, its ACPI companion
device) instead of an ACPI handle corresponding to it. Introduce two
new macros for manipulating that pointer in a CONFIG_ACPI-safe way,
ACPI_COMPANION() and ACPI_COMPANION_SET(), and rework the
ACPI_HANDLE() macro to take the above changes into account.
Drop the ACPI_HANDLE_SET() macro entirely and rework its users to
use ACPI_COMPANION_SET() instead. For some of them who used to
pass the result of acpi_get_child() directly to ACPI_HANDLE_SET()
introduce a helper routine acpi_preset_companion() doing an
equivalent thing.
The main motivation for doing this is that there are things
represented by struct acpi_device objects that don't have valid
ACPI handles (so called fixed ACPI hardware features, such as
power and sleep buttons) and we would like to create platform
device objects for them and "glue" them to their ACPI companions
in the usual way (which currently is impossible due to the
lack of valid ACPI handles). However, there are more reasons
why it may be useful.
First, struct acpi_device pointers allow of much better type checking
than void pointers which are ACPI handles, so it should be more
difficult to write buggy code using modified struct acpi_dev_node
and the new macros. Second, the change should help to reduce (over
time) the number of places in which the result of ACPI_HANDLE() is
passed to acpi_bus_get_device() in order to obtain a pointer to the
struct acpi_device associated with the given "physical" device,
because now that pointer is returned by ACPI_COMPANION() directly.
Finally, the change should make it easier to write generic code that
will build both for CONFIG_ACPI set and unset without adding explicit
compiler directives to it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> # on Haswell
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com> # for ATA and SDIO part
Currently, initialize _CRS resource code in IA64 make pci_acpi_scan_root()
some lengthiness. Introduce probe_pci_root_info() to manage it like in X86,
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-ia64@vger.kernel.org
Signed-off-by: Tony Luck <tony.luck@intel.com>
Set IA64 host bridge release function to make sure root bridge
related resources get freed during root bus removal.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-ia64@vger.kernel.org
Signed-off-by: Tony Luck <tony.luck@intel.com>
If pci_create_root_bus() return fail, we should release
pci root info, pci controller etc.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-ia64@vger.kernel.org
Signed-off-by: Tony Luck <tony.luck@intel.com>
We need to pass around info for release function.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-ia64@vger.kernel.org
Signed-off-by: Tony Luck <tony.luck@intel.com>
Currently, pcibios_resource_to_bus() and pcibios_bus_to_resource()
functions use pci_host_bridge to translate bus side address from/to
cpu side address. The pci_window in pci_controller never be used again.
So we remove pci_window in pci_controller and embed hostbridge resource
into pci_root_info. Bjorn suggested to implement hostbridge resources
release in IA64 like in X86, this patch is to prepare for that.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: linux-ia64@vger.kernel.org
Signed-off-by: Tony Luck <tony.luck@intel.com>
Host bridge hotplug
- Major overhaul of ACPI host bridge add/start (Rafael Wysocki, Yinghai Lu)
- Major overhaul of PCI/ACPI binding (Rafael Wysocki, Yinghai Lu)
- Split out ACPI host bridge and ACPI PCI device hotplug (Yinghai Lu)
- Stop caching _PRT and make independent of bus numbers (Yinghai Lu)
PCI device hotplug
- Clean up cpqphp dead code (Sasha Levin)
- Disable ARI unless device and upstream bridge support it (Yijing Wang)
- Initialize all hot-added devices (not functions 0-7) (Yijing Wang)
Power management
- Don't touch ASPM if disabled (Joe Lawrence)
- Fix ASPM link state management (Myron Stowe)
Miscellaneous
- Fix PCI_EXP_FLAGS accessor (Alex Williamson)
- Disable Bus Master in pci_device_shutdown (Konstantin Khlebnikov)
- Document hotplug resource and MPS parameters (Yijing Wang)
- Add accessor for PCIe capabilities (Myron Stowe)
- Drop pciehp suspend/resume messages (Paul Bolle)
- Make pci_slot built-in only (not a module) (Jiang Liu)
- Remove unused PCI/ACPI bind ops (Jiang Liu)
- Removed used pci_root_bus (Bjorn Helgaas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ER3b
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Major overhaul of ACPI host bridge add/start (Rafael Wysocki, Yinghai Lu)
- Major overhaul of PCI/ACPI binding (Rafael Wysocki, Yinghai Lu)
- Split out ACPI host bridge and ACPI PCI device hotplug (Yinghai Lu)
- Stop caching _PRT and make independent of bus numbers (Yinghai Lu)
PCI device hotplug
- Clean up cpqphp dead code (Sasha Levin)
- Disable ARI unless device and upstream bridge support it (Yijing Wang)
- Initialize all hot-added devices (not functions 0-7) (Yijing Wang)
Power management
- Don't touch ASPM if disabled (Joe Lawrence)
- Fix ASPM link state management (Myron Stowe)
Miscellaneous
- Fix PCI_EXP_FLAGS accessor (Alex Williamson)
- Disable Bus Master in pci_device_shutdown (Konstantin Khlebnikov)
- Document hotplug resource and MPS parameters (Yijing Wang)
- Add accessor for PCIe capabilities (Myron Stowe)
- Drop pciehp suspend/resume messages (Paul Bolle)
- Make pci_slot built-in only (not a module) (Jiang Liu)
- Remove unused PCI/ACPI bind ops (Jiang Liu)
- Removed used pci_root_bus (Bjorn Helgaas)"
* tag 'pci-v3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (51 commits)
PCI/ACPI: Don't cache _PRT, and don't associate them with bus numbers
PCI: Fix PCI Express Capability accessors for PCI_EXP_FLAGS
ACPI / PCI: Make pci_slot built-in only, not a module
PCI/PM: Clear state_saved during suspend
PCI: Use atomic_inc_return() rather than atomic_add_return()
PCI: Catch attempts to disable already-disabled devices
PCI: Disable Bus Master unconditionally in pci_device_shutdown()
PCI: acpiphp: Remove dead code for PCI host bridge hotplug
PCI: acpiphp: Create companion ACPI devices before creating PCI devices
PCI: Remove unused "rc" in virtfn_add_bus()
PCI: pciehp: Drop suspend/resume ENTRY messages
PCI/ASPM: Don't touch ASPM if forcibly disabled
PCI/ASPM: Deallocate upstream link state even if device is not PCIe
PCI: Document MPS parameters pci=pcie_bus_safe, pci=pcie_bus_perf, etc
PCI: Document hpiosize= and hpmemsize= resource reservation parameters
PCI: Use PCI Express Capability accessor
PCI: Introduce accessor to retrieve PCIe Capabilities Register
PCI: Put pci_dev in device tree as early as possible
PCI: Skip attaching driver in device_add()
PCI: acpiphp: Keep driver loaded even if no slots found
...
The ACPI handles of PCI root bridges need to be known to
acpi_bind_one(), so that it can create the appropriate
"firmware_node" and "physical_node" files for them, but currently
the way it gets to know those handles is not exactly straightforward
(to put it lightly).
This is how it works, roughly:
1. acpi_bus_scan() finds the handle of a PCI root bridge,
creates a struct acpi_device object for it and passes that
object to acpi_pci_root_add().
2. acpi_pci_root_add() creates a struct acpi_pci_root object,
populates its "device" field with its argument's address
(device->handle is the ACPI handle found in step 1).
3. The struct acpi_pci_root object created in step 2 is passed
to pci_acpi_scan_root() and used to get resources that are
passed to pci_create_root_bus().
4. pci_create_root_bus() creates a struct pci_host_bridge object
and passes its "dev" member to device_register().
5. platform_notify(), which for systems with ACPI is set to
acpi_platform_notify(), is called.
So far, so good. Now it starts to be "interesting".
6. acpi_find_bridge_device() is used to find the ACPI handle of
the given device (which is the PCI root bridge) and executes
acpi_pci_find_root_bridge(), among other things, for the
given device object.
7. acpi_pci_find_root_bridge() uses the name (sic!) of the given
device object to extract the segment and bus numbers of the PCI
root bridge and passes them to acpi_get_pci_rootbridge_handle().
8. acpi_get_pci_rootbridge_handle() browses the list of ACPI PCI
root bridges and finds the one that matches the given segment
and bus numbers. Its handle is then used to initialize the
ACPI handle of the PCI root bridge's device object by
acpi_bind_one(). However, this is *exactly* the ACPI handle we
started with in step 1.
Needless to say, this is quite embarassing, but it may be avoided
thanks to commit f3fd0c8 (ACPI: Allow ACPI handles of devices to be
initialized in advance), which makes it possible to initialize the
ACPI handle of a device before passing it to device_register().
Accordingly, add a new __weak routine, pcibios_root_bridge_prepare(),
defaulting to an empty implementation that can be replaced by the
interested architecutres (x86 and ia64 at the moment) with functions
that will set the root bridge's ACPI handle before its dev member is
passed to device_register(). Make both x86 and ia64 provide such
implementations of pcibios_root_bridge_prepare() and remove
acpi_pci_find_root_bridge() and acpi_get_pci_rootbridge_handle() that
aren't necessary any more.
Included is a fix for breakage on systems with non-ACPI PCI host
bridges from Bjorn Helgaas.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use kzalloc() so the struct resource doesn't contain garbage in
fields we don't initialize.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64@vger.kernel.org
Most architectures implement this in exactly the same way. Instead of
having each architecture duplicate this function, provide a single
implementation in the core and make it a weak symbol so that it can be
overridden on architectures where it is required.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the __init annotations in order to keep pci_fixup_irqs() around
after init (e.g. for hotplug). This requires the same change for the
implementation of pcibios_update_irq() on all architectures. While at
it, all __devinit annotations are removed as well, since they will be
useless now that HOTPLUG is always on.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZFHB
-----END PGP SIGNATURE-----
Merge tag 'please-pull-ia64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull misc ia64 build fixes from Tony Luck.
* tag 'please-pull-ia64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts
[IA64] Rename platform_name to ia64_platform_name
[IA64] Mark PARAVIRT and KVM as broken
The macro name is too generic and conflicts with
snd_soc_dai_link.platform_name, which triggers lots of build errors.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* pci/myron-pcibios_setup:
xtensa/PCI: factor out pcibios_setup()
x86/PCI: adjust section annotations for pcibios_setup()
unicore32/PCI: adjust section annotations for pcibios_setup()
tile/PCI: factor out pcibios_setup()
sparc/PCI: factor out pcibios_setup()
sh/PCI: adjust section annotations for pcibios_setup()
sh/PCI: factor out pcibios_setup()
powerpc/PCI: factor out pcibios_setup()
parisc/PCI: factor out pcibios_setup()
MIPS/PCI: adjust section annotations for pcibios_setup()
MIPS/PCI: factor out pcibios_setup()
microblaze/PCI: factor out pcibios_setup()
ia64/PCI: factor out pcibios_setup()
cris/PCI: factor out pcibios_setup()
alpha/PCI: factor out pcibios_setup()
PCI: pull pcibios_setup() up into core
The PCI core provides a generic pcibios_setup() routine. Drop this
architecture-specific version in favor of that.
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add the host bridge bus number aperture from _CRS to the resource list.
Like the MMIO and I/O port apertures, this is used when assigning
resources to hot-added devices or in the case of conflicts.
[bhelgaas: changelog]
CC: Tony Luck <tony.luck@intel.com>
CC: Fenghua Yu <fenghua.yu@intel.com>
CC: linux-ia64@vger.kernel.org
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Replace the struct pci_bus secondary/subordinate members with the
struct resource busn_res. Later we'll build a resource tree of these
bus numbers.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Disintegrate asm/system.h for IA64.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Tony Luck <tony.luck@intel.com>
cc: linux-ia64@vger.kernel.org
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: Tony Luck <tony.luck@intel.com>
CC: Jack Steiner <steiner@sgi.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Convert from pci_create_bus() to pci_create_root_bus(). This way the root
bus resources are correct immediately. This fixes the problem of "early"
and "header" quirks seeing incorrect root bus resources.
We can't use pci_scan_root_bus() because, like x86, ACPI hotplug currently
requires pci_bus_add_devices() in a separate host bridge .start() method.
v2: fix compile error by using window resource pointer instead
CC: Tony Luck <tony.luck@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This doesn't change any functionality, but it makes a subsequent patch
slightly simpler.
CC: Tony Luck <tony.luck@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch converts IA64's architecture-specific 'pcibios_set_master()'
routine to a non-inlined function. This will allow follow on
patches to create a generic 'pcibios_set_master()' function using the
'__weak' attribute which can be used by all architectures as a default
which, if necessary, can then be over-ridden by architecture-
specific code.
Converting 'pci_bios_set_master()' to a non-inlined function will allow
IA64's 'pcibios_set_master()' implementation to remain architecture-
specific after the generic version is introduced and thus, not change
current behavior.
No functional change.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The acpi_pci_root structure contains all the individual items (acpi_device,
domain, bus number) we pass to pci_acpi_scan_root(), so just pass the
single acpi_pci_root pointer directly.
This will make it easier to add _CBA support later. For _CBA, we need the
entire downstream bus range, not just the base bus number. We have that in
the acpi_pci_root structure, so passing the pointer makes it available to
the arch-specific code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously we used a table of size PCI_BUS_NUM_RESOURCES (16) for resources
forwarded to a bus by its upstream bridge. We've increased this size
several times when the table overflowed.
But there's no good limit on the number of resources because host bridges
and subtractive decode bridges can forward any number of ranges to their
secondary buses.
This patch reduces the table to only PCI_BRIDGE_RESOURCE_NUM (4) entries,
which corresponds to the number of windows a PCI-to-PCI (3) or CardBus (4)
bridge can positively decode. Any additional resources, e.g., PCI host
bridge windows or subtractively-decoded regions, are kept in a list.
I'd prefer a single list rather than this split table/list approach, but
that requires simultaneous changes to every architecture. This approach
only requires immediate changes where we set up (a) host bridges with more
than four windows and (b) subtractive-decode P2P bridges, and we can
incrementally change other architectures to use the list.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; this converts loops that iterate from 0 to
PCI_BUS_NUM_RESOURCES through pci_bus resource[] table to use the
pci_bus_for_each_resource() iterator instead.
This doesn't change the way resources are stored; it merely removes
dependencies on the fact that they're in a table.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Now that we return the new resource start position, there is no
need to update "struct resource" inside the align function.
Therefore, mark the struct resource as const.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bjorn Helgaas