When using a protocol v2 or v3 hardware, elantech uses the function
elantech_report_semi_mt_data() to report data. This devices are rather
creepy because if num_finger is 3, (x2,y2) is (0,0). Yes, only one valid
touch is reported.
Anyway, userspace (libinput) is now confused by these (0,0) touches,
and detect them as palm, and rejects them.
Commit 3c0213d17a ("Input: elantech - fix semi-mt protocol for v3 HW")
was sufficient enough for xf86-input-synaptics and libinput before it has
palm rejection. Now we need to actually tell libinput that this device is
a semi-mt one and it should not rely on the actual values of the 2 touches.
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch moves v3 pinnacle code for trackstick detection from
alps_hw_init_v3() to alps_set_protocol() so ALPS_DUALPOINT flag can be
cleared before registering trackstick input device in kernel.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds detection of trackstick for v7 protocol devices. Code in
this patch is used in official Dell touchpad linux drivers for Dell models:
Dell Latitude E5250/5250, E5450/5450, E5550/5550
Detection code and base reg for alps v3 rushmore and v7 devices is exacly
same.
Also user in bug https://bugzilla.kernel.org/show_bug.cgi?id=94801 reported
that Toshiba Sattellite Z30-A-1DG has only alps v7 touchpad device without
trackstick and kernel reports to userspace also redundant trackstick
device.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This makes Logitech PS2++ protocol implementation consistent with
the naming in other protocols. Also mark the stub as "static inline"
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
PS/2 protocol is slow, and using it with pass-through port (where we
encapsulate PS/2 into PS/2) is slower yet so it takes quite a bit of time
to do full protocol discovery for device attached to a pass-through port.
However, so far we have not see anything but trackpoints or basic PS/2
mice on pass-through ports, so let's limit protocols that we probe there
to Trackpoint, IntelliMouse Explorer, IntelliMouse, and bare PS/2 protocol,
and avoid other extended protocols, such as Synaptics, ALPS, etc.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation of limiting protocols that we try on pass-through ports,
let's rework initialization code and factor common code into
psmouse_try_protocol() that accepts protocol type (instead of detec()
function pointer) and can, for most protocols, perform both detection and
initialization.
Note that this removes option of forcing Lifebook protocol on devices that
are not recognized by lifebook_detect() as having the hardware, but I do
not recall anyone using this option.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We move protocol descriptions and psmouse_find_by_type() and
pmouse_find_by_name() so that we can use them without forward declarations
in the subsequent patches.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When Cypress protocol support is disabled cypress_init() is a stub that
always returns -ENOSYS, so there is not point in testing for
CONFIG_MOUSE_PS2_CYPRESS after we decided that we are dealing with a
Cypress device. Also, we should only be calling cypress_detect() when
set_properties argument is "true", like with other protocols.
There is a slight change in behavior to make follow-up patches more
uniform: when we detect Cypress but its initialization fails, instead of
immediately returning PSMOUSE_PS2 protocol we now continue trying
IntelliMouse [Explorer]. Given that Cypress devices only have issue with
Sentelic probes probing Imtellimouse should be safe.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The fact that we were calling focaltech_init() even when Focaltech support
is disabled was confusing. Rearrange the code so that if support is
disabled we continue to fall through the rest of protocol probing code
until we get to full reset that Focaltech devices need to work properly.
Also, replace focaltech_init() with a stub now that it is only called when
protocol is enabled.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The module was using non-standard comment style with comment blocks often
starting at the very beginning of a line instead of being aligned with the
code. Let's switch to standard formatting.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of a series mostly exclusive "if" statements testing protocol type
of the mouse let's use "switch" statement.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Previously the "vendor" and "product" IDs for the elan_i2c driver simply
reported 0000. This patch modifies the elan_i2c driver to include the
Elan vendor ID and the touchpad's product id under
input/input*/{vendor,product}.
Specifically, this is to allow us to apply a generic Elan gestures config
that will apply to all Elan touchpads on ChromeOS. These configs match to
input devices in various ways, but one major way is by matching on vendor
ID. Adding this patch allows the default Elan touchpad config to be
applied to Elan touchpads in this kernel by matching on devices that have
vendor ID 04f3.
Note that product ID is also available via custom sysfs entry "product_id"
as well.
Signed-off-by: Charlie Mooney <charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Another Lifebook machine that needs the same quirk as other similar
models to make the driver working.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=883192
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit 92bac83dd7 ("Input: alps - non interleaved V2 dualpoint has
separate stick button bits") assumes that all alps v2 non-interleaved
dual point setups have the separate stick button bits.
Later we limited this to Dell laptops only because of reports that this
broke things on non Dell laptops. Now it turns out that this breaks things
on the Dell Latitude D600 too. So it seems that only the Dell Latitude
D420/430/620/630, which all share the same touchpad / stick combo,
have these separate bits.
This patch limits the checking of the separate bits to only these models
fixing regressions with other models.
Reported-and-tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@vger.kernel.org
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-By: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix the copy paste error on the electrodes_rx value set code which will
cause the electrodes_rx value be always set to the value of electrodes_y.
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit e51e38494a8ecc18650efb0c840600637891de2c: we
actually do want the device to work in extended W mode, as this is the
mode that allows us receiving multiple contact information.
Cc: stable@vger.kernel.org
In order to support more projects in the future, we expand the
maximum product_id value form 0xFF to 0xFFFF.
Signed-off by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Asus X456UA has an ELAN1000 touchpad with IAP version 0xe. This is
unknown to elan_get_fwinfo() so driver probe fails and I am left with an
unusable touchpad.
However, the fwinfo is not required for general driver usage, it is only
needed if the user decides to upload new firmware.
Adjust the driver so that we do not abort probe when we encounter
unexpected IAP version, but rather warn user that firmware update feature
of the driver will not work.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This ACPI ID present in the DSDT of the ASUS E202SA laptop.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When driver is in IAP mode ic_type query may return 0xff. However
iap_version will always be valid, so let's use it to determine parameters
of the firmware that the controller is supposed to accept.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Search for "vaildpage_count" and replace with "validpage_count".
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are trackpoint devices that fail to respond to the PS2 command
PSMOUSE_CMD_GETID if immediately queried after the parent device is
deactivated. Add a small delay for the hardware to get in a sane state
before sending any PS2 commands.
One example of such a system is:
Lenovo ThinkPad X120e, model 30515QG
synaptics: Touchpad model: 1, fw: 8.0, id: 0x1e2b1, caps: 0xd001a3/0x940300/0x121c00, board id: 1811, fw id: 797391
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Bit 2 of the mode byte has dual meaning: it can disable reporting of
gestures when touchpad works in Relative mode or normal Absolute mode,
or it can enable so called Extended W-Mode when touchpad uses enhanced
Absolute mode (W-mode). The extended W-Mode confuses our driver and
causes missing button presses on some Thinkpads (x250, T450s), so let's
make sure we do not enable it.
Also, according to the spec W mode "... bit is defined only in Absolute
mode on pads whose capExtended capability bit is set. In Relative mode and
in TouchPads without this capability, the bit is reserved and should be
left at 0.", so let's make sure we respect this requirement as well.
Reported-by: Nick Bowler <nbowler@draconx.ca>
Suggested-by: Gabor Balla <gaborwho@gmail.com>
Tested-by: Gabor Balla <gaborwho@gmail.com>
Tested-by: Nick Bowler <nbowler@draconx.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Enable ELAN0100 touchpad driver, found on a Asus X205TA laptop, to
gai 2,3 fingers tap and 2 fingers scroll.
Signed-off-by: Michele Curti <michele.curti@gmail.com>
Reviewed-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I have a static checker that complains when we check for an upper bound
but don't have a corresponding check for a lower bound. With this code,
the upper bound check seems not really required, so it is not a bug to
leave the lower bound check out as well. But let's silence the warning
by making these variables unsigned.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It takes a bit of time to go through controller power up sequence and
initialization. To not stall the overall boot progress let's probe the
controller asynchronously, given that userspace is usually prepared for
hot-plugging of input devices and thus does not rely on particular
ordering.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is no need to check the packet[0] for sanity check when doing
elantech_packet_check_v4() function for fw_version = 0x470f01 touchpad.
Signed-off by: Duson Lin <dusonlin@emc.com.tw>
Reviewed-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It turns out that only Dell laptops have the separate button bits for
v2 dualpoint sticks and that commit 92bac83dd7 ("Input: alps - non
interleaved V2 dualpoint has separate stick button bits") causes
regressions on Toshiba laptops.
This commit adds a check for Dell laptops to the code for handling these
extra button bits, fixing this regression.
This patch has been tested on a Dell Latitude D620 to make sure that it
does not reintroduce the original problem.
Reported-and-tested-by: Douglas Christman <douglaschristman@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Avoid the driver generate warning message when the cyapa driver working
with the old Gen5 trackpad device which does not support the proximity
function. Those old Gen5 trackpad device all have the platform version
less than 2.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add device tree support for Cypress trackpad devices.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need to power up the chip before we can initialize it.
On systems that delegate task of powering up regulators to firmware we
assume that we'll be simply given a dummy regulator.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for the MacBookPro12,1 model. This patch needs to be
applied together with the accompanied HID patch, as usual.
Tested-by: John Horan <knasher@gmail.com>
Tested-by: Jochen Radmacher <jradmacher@gmx.de>
Tested-by: Yang Hongyang <burnef@gmail.com>
Tested-by: Yen-Chin, Lee <coldnew.tw@gmail.com>
Tested-by: George Hilios <ghilios@gmail.com>
Tested-by: Janez Urevc <janez@janezurevc.name>
Signed-off-by: Henrik Rydberg <rydberg@bitmath.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With the advent of the Macbook Pro 12, we see a new generation of
trackpads, capable of force sensoring and haptic feedback.
This patch prepares for the new device by adding configuration data
for the code paths that would otherwise look different.
Tested-by: John Horan <knasher@gmail.com>
Tested-by: Jochen Radmacher <jradmacher@gmx.de>
Tested-by: Yang Hongyang <burnef@gmail.com>
Tested-by: Yen-Chin, Lee <coldnew.tw@gmail.com>
Tested-by: George Hilios <ghilios@gmail.com>
Tested-by: Janez Urevc <janez@janezurevc.name>
Signed-off-by: Henrik Rydberg <rydberg@bitmath.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make extended capabilities obtained through $10 query also available in
touchpad identification.
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add CYTP0002 to the list of ACPI HIDs recognized by the driver.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix the the runtime suspend power management not working issue when system
starts up and before user touches the trackpad device.
TEST=test on Chromebook.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Gen5 and Gen6 trackpad devices are able to detect and report object
proximity data/events, add this function support in the cyapa driver
through the ABS_DISTANCE event.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Based on the cyapa core, add support for basic functionality of the gen6
trackpad devices. The driver can automatically determine what protocol
(gen3, gen5, or gen6) should be used with the attached trackpad device.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Change 'gen5' to 'pip' for all macros, variables and functions that are
shared between gen5 and gen6 modules to make naming more clear and
readable.
Also fix a few spelling errors.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVrBp0AAoJEHm+PkMAQRiGADsH/iCVjA1x+a19xpeuHNJcjcQR
Lin8td8zdUxereBNQOFjnkhCmKtzLODXGkQdYFaWZx8mbEQ93wC+nPV8O+LsqPbI
T/2MjJ78IjlNsoTyE4b1AhqpASsxrLZJNB+f9dd251f1BSAzKfRER0G46WxbOPN7
9HdzCMbtx03ZJkr9baE6alljxA43O5mpDzpotKIagfTMQr5h0ra16uXlmVXFjHRs
roNJsugwKxJPnVmLWWOM1JsAjRSMBAXQUQxhJJCMDOhgZZ5KR1z6L30ESeFTUhvh
WG/2MEfyVYXn91kV0N+AUCuOFHTv6uiaz3RaRVJFDSv3sPOh1WQ9tQHxyrBsqyY=
=MA/P
-----END PGP SIGNATURE-----
Merge tag 'v4.2-rc3' into next
Sync up with Linux 4.2-rc3 to bring in infrastructure (OF) pieces.
ELAN0600 seems to work just fine in mouse emulation mode through i2c-hid,
but to have full raw touch support we need to register it in elan_i2c.ko
Reported-and-tested-by: Alessio Treglia <alessio@debian.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry Torokhov