Commit Graph

92 Commits

Author SHA1 Message Date
Benjamin Herrenschmidt 396a1a5832 [POWERPC] Fix mmap of PCI resource with hack for X
The powerpc version of pci_resource_to_user() and associated hooks
used by /proc/bus/pci and /sys/bus/pci mmap have been broken for some
time on machines that don't have a 1:1 mapping of devices (basically
on non-PowerMacs) and have PCI devices above 32 bits.

This attempts to fix it as well as possible.

The rule is supposed to be that pci_resource_to_user() always converts
the resources back into a BAR values since that's what the /proc
interface was supposed to deal with. However, for X to work on
platforms where PCI MMIO is not mapped 1:1, it became a habit of
platforms like powerpc to pass "fixed up" values there since X expects
to be able to use values from /proc/bus/pci/devices as offsets to mmap
of /dev/mem...

So we keep that contraption here, causing also /sys/*/resource to
expose fully absolute MMIO addresses instead of BAR values, which is
ugly, but should still work as long as those are only used to calculate
alignment within a page.

X is still broken when built 32 bits on machines where PCI MMIO can be
above 32-bit space unfortunately.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-08 17:21:06 +11:00
Yan Burman f8485350c2 [POWERPC] Replace kmalloc+memset with kzalloc
Replace kmalloc+memset with kzalloc.

Signed-off-by: Yan Burman <burman.yan@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04 20:42:09 +11:00
Benjamin Herrenschmidt 4cb3cee03d [POWERPC] Allow hooking of PCI MMIO & PIO accessors on 64 bits
This patch reworks the way iSeries hooks on PCI IO operations (both MMIO
and PIO) and provides a generic way for other platforms to do so (we
have need to do that for various other platforms).

While reworking the IO ops, I ended up doing some spring cleaning in
io.h and eeh.h which I might want to split into 2 or 3 patches (among
others, eeh.h had a lot of useless stuff in it).

A side effect is that EEH for PIO should work now (it used to pass IO
ports down to the eeh address check functions which is bogus).

Also, new are MMIO "repeat" ops, which other archs like ARM already had,
and that we have too now: readsb, readsw, readsl, writesb, writesw,
writesl.

In the long run, I might also make EEH use the hooks instead
of wrapping at the toplevel, which would make things even cleaner and
relegate EEH completely in platforms/iseries, but we have to measure the
performance impact there (though it's really only on MMIO reads)

Since I also need to hook on ioremap, I shuffled the functions a bit
there. I introduced ioremap_flags() to use by drivers who want to pass
explicit flags to ioremap (and it can be hooked). The old __ioremap() is
still there as a low level and cannot be hooked, thus drivers who use it
should migrate unless they know they want the low level version.

The patch "arch provides generic iomap missing accessors" (should be
number 4 in this series) is a pre-requisite to provide full iomap
API support with this patch.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04 20:38:52 +11:00
Benjamin Herrenschmidt 4c9d2800be [POWERPC] Generic OF platform driver for PCI host bridges.
When enabled in Kconfig, it will pick up any of_platform_device
matching it's match list (currently type "pci", "pcix", "pcie",
or "ht" and setup a PHB for it.

Platform must provide a ppc_md.pci_setup_phb() for it to work
(for doing the necessary initialisations specific to a given PHB
like setting up the config space ops).

It's currently only available on 64 bits as the 32 bits PCI code
can't quite cope with it in it's current form. I will fix that
later.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04 20:38:49 +11:00
Benjamin Herrenschmidt 803d4573e6 [POWERPC] Add "parent" struct device for PCI host bridges
Add a "parent" struct device to our PCI host bridge data structure so that
PCI can be rooted off another device in sysfs.

Note that arch/ppc doesn't use it, only arch/powerpc, though it's available
for both 32 and 64 bits.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04 20:38:47 +11:00
Benjamin Herrenschmidt e557a1c96c [POWERPC] Resolve the parent address of a PCI bus range
When parsing the OF "ranges" properties of PCI host busses to determine
the mapping of a PCI bus, we need to translate the "parent" address using
the prom_parse.c routines in order to obtain a CPU physical address.

This wasn't necessary while PCI busses were always at the root of the
device-tree but this is no longer the case on Cell where they can be
anywhere in the tree.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04 20:38:43 +11:00
Benjamin Herrenschmidt 12d04eef92 [POWERPC] Refactor 64 bits DMA operations
This patch completely refactors DMA operations for 64 bits powerpc. 32 bits
is untouched for now.

We use the new dev_archdata structure to add the dma operations pointer
and associated data to struct device. While at it, we also add the OF node
pointer and numa node. In the future, we might want to look into merging
that with pci_dn as well.

The old vio, pci-iommu and pci-direct DMA ops are gone. They are now replaced
by a set of generic iommu and direct DMA ops (non PCI specific) that can be
used by bus types. The toplevel implementation is now inline.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04 20:38:40 +11:00
Benjamin Herrenschmidt f90bb153b1 [POWERPC] Make pci_read_irq_line the default
This patch reworks the way IRQs are fixed up on PCI for arch powerpc.

It makes pci_read_irq_line() called by default in the PCI code for
devices that are probed, and add an optional per-device fixup in
ppc_md for platforms that really need to correct what they obtain
from pci_read_irq_line().

It also removes ppc_md.irq_bus_setup which was only used by pSeries
and should not be needed anymore.

I've also removed the pSeries s7a workaround as it can't work with
the current interrupt code anyway. I'm trying to get one of these
machines working so I can test a proper fix for that problem.

I also haven't updated the old-style fixup code from 85xx_cds.c
because it's actually buggy :) It assigns pci_dev->irq hard coded
numbers which is no good with the new IRQ mapping code. It should
at least use irq_create_mapping(NULL, hard_coded_number); and possibly
also set_irq_type() to set them as level low.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04 16:00:04 +11:00
s.hauer@pengutronix.de 99a565bab1 [PATCH] Remove occurences of PPC_MULTIPLATFORM in pci_64.c
Since iSeries is merged to MULTIPLATFORM, there is no way to build a 64bit
kernel without MULTIPLATFORM, so PPC_MULTIPLATFORM can be removed in
64bit-only files.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-11-13 14:44:59 +11:00
Anton Blanchard 284a940675 [POWERPC] Check for offline nodes in pci NUMA code
During boot we bring up all memory and cpu nodes. Normally a PCI device
will be in one of these online nodes, however in some weird setups it
may not.

We have only seen this in the lab but we may as well check for the case
and fallback to -1 (all nodes).

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-16 15:53:30 +10:00
Stephen Rothwell eecba334bd [POWERPC] modify PCI code for a merged kernel
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
2006-09-25 13:35:09 +10:00
Paul Mackerras aa43f77939 Merge branch 'merge' 2006-08-31 15:45:48 +10:00
Benjamin Herrenschmidt 006b64de60 [POWERPC] Make OF irq map code detect more error cases
Device-tree bugs on js20 with some versions of SLOF were causing the
interrupt for IDE to not be parsed correctly and fail to boot. This
patch adds a bit more sanity checking to the parser to detect some of
those errors and fail instead of returning bogus information.  The
powerpc PCI code can then trigger a fallback that works on those
machines.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-08-30 14:31:03 +10:00
Paul Mackerras 57cad8084e Merge branch 'merge' 2006-08-01 10:37:25 +10:00
Jeremy Kerr a7f67bdf2c [POWERPC] Constify & voidify get_property()
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.

powerpc core changes.

Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-07-31 15:55:04 +10:00
Benjamin Herrenschmidt 6e99e45828 [PATCH] powerpc: fix trigger handling in the new irq code
This patch slightly reworks the new irq code to fix a small design error.  I
removed the passing of the trigger to the map() calls entirely, it was not a
good idea to have one call do two different things.  It also fixes a couple of
corner cases.

Mapping a linux virtual irq to a physical irq now does only that.  Setting the
trigger is a different action which has a different call.

The main changes are:

- I no longer call host->ops->map() for an already mapped irq, I just return
  the virtual number that was already mapped.  It was called before to give an
  opportunity to change the trigger, but that was causing issues as that could
  happen while the interrupt was in use by a device, and because of the
  trigger change, map would potentially muck around with things in a racy way.
   That was causing much burden on a given's controller implementation of
  map() to get it right.  This is much simpler now.  map() is only called on
  the initial mapping of an irq, meaning that you know that this irq is _not_
  being used.  You can initialize the hardware if you want (though you don't
  have to).

- Controllers that can handle different type of triggers (level/edge/etc...)
  now implement the standard irq_chip->set_type() call as defined by the
  generic code.  That means that you can use the standard set_irq_type() to
  configure an irq line manually if you wish or (though I don't like that
  interface), pass explicit trigger flags to request_irq() as defined by the
  generic kernel interfaces.  Also, using those interfaces guarantees that
  your controller set_type callback is called with the descriptor lock held,
  thus providing locking against activity on the same interrupt (including
  mask/unmask/etc...) automatically.  A result is that, for example, MPIC's
  own map() implementation calls irq_set_type(NONE) to configure the hardware
  to the default triggers.

- To allow the above, the irq_map array entry for the new mapped interrupt
  is now set before map() callback is called for the controller.

- The irq_create_of_mapping() (also used by irq_of_parse_and_map()) function
  for mapping interrupts from the device-tree now also call the separate
  set_irq_type(), and only does so if there is a change in the trigger type.

- While I was at it, I changed pci_read_irq_line() (which is the helper I
  would expect most archs to use in their pcibios_fixup() to get the PCI
  interrupt routing from the device tree) to also handle a fallback when the
  DT mapping fails consisting of reading the PCI_INTERRUPT_PIN to know wether
  the device has an interrupt at all, and the the PCI_INTERRUPT_LINE to get an
  interrupt number from the device.  That number is then mapped using the
  default controller, and the trigger is set to level low.  That default
  behaviour works for several platforms that don't have a proper interrupt
  tree like Pegasos.  If it doesn't work for your platform, then either
  provide a proper interrupt tree from the firmware so that fallback isn't
  needed, or don't call pci_read_irq_line()

- Add back a bit that got dropped by my main rework patch for properly
  clearing pending IPIs on pSeries when using a kexec

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10 13:24:20 -07:00
Jeremy Kerr 3da27289a8 [POWERPC] Remove linux,pci-domain properties
The linux,pci-domain property is no longer used by DLPAR/PCI Hotplug
utilites, or LSVPD. This change removes it.

Built for ppc64_defconfig.

Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-07-07 20:19:16 +10:00
Benjamin Herrenschmidt 0ebfff1491 [POWERPC] Add new interrupt mapping core and change platforms to use it
This adds the new irq remapper core and removes the old one.  Because
there are some fundamental conflicts with the old code, like the value
of NO_IRQ which I'm now setting to 0 (as per discussions with Linus),
etc..., this commit also changes the relevant platform and driver code
over to use the new remapper (so as not to cause difficulties later
in bisecting).

This patch removes the old pre-parsing of the open firmware interrupt
tree along with all the bogus assumptions it made to try to renumber
interrupts according to the platform. This is all to be handled by the
new code now.

For the pSeries XICS interrupt controller, a single remapper host is
created for the whole machine regardless of how many interrupt
presentation and source controllers are found, and it's set to match
any device node that isn't a 8259.  That works fine on pSeries and
avoids having to deal with some of the complexities of split source
controllers vs. presentation controllers in the pSeries device trees.

The powerpc i8259 PIC driver now always requests the legacy interrupt
range. It also has the feature of being able to match any device node
(including NULL) if passed no device node as an input. That will help
porting over platforms with broken device-trees like Pegasos who don't
have a proper interrupt tree.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-07-03 21:36:01 +10:00
Jörn Engel 6ab3d5624e Remove obsolete #include <linux/config.h>
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-30 19:25:36 +02:00
Greg Kroah-Hartman e31dd6e452 [PATCH] 64bit resource: change pci core and arch code to use resource_size_t
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>

Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-27 09:24:00 -07:00
Christoph Lameter 68402ddc67 [PATCH] mm: remove VM_LOCKED before remap_pfn_range and drop VM_SHM
Remove VM_LOCKED before remap_pfn range from device drivers and get rid of
VM_SHM.

remap_pfn_range() already sets VM_IO.  There is no need to set VM_SHM since
it does nothing.  VM_LOCKED is of no use since the remap_pfn_range does not
place pages on the LRU.  The pages are therefore never subject to swap
anyways.  Remove all the vm_flags settings before calling remap_pfn_range.

After removing all the vm_flag settings no use of VM_SHM is left.  Drop it.

Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-25 10:00:55 -07:00
Anton Blanchard 357518fa34 [POWERPC] pcibus_to_node fixes
of_node_to_nid returns -1 if the associativity cannot be found. This
means pcibus_to_cpumask has to be careful not to pass a negative index into
node_to_cpumask.

Since pcibus_to_node could be used a lot, and of_node_to_nid is slow (it
walks a list doing strcmps), lets also cache the node in the
pci_controller struct.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-06-15 19:31:26 +10:00
Jake Moilanen bb53bb3dcb [POWERPC] Add support for PCI-Express nodes in the device tree
This adds support to recognize the PCIe device_type "pciex" and made
the portdrv buildable.

Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-06-15 19:31:25 +10:00
Stephen Rothwell efbd386967 [PATCH] powerpc: iSeries PCI devices can now have a devpsec attribute
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-05-24 16:08:56 +10:00
Olof Johansson e884e9c5f2 [PATCH] powerpc: Quiet PCI init printouts
Quiet some of the more debug related output from the pci probe routines.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-04-22 18:45:14 +10:00
Anton Blanchard c256f4b959 [PATCH] powerpc: remove io_page_mask
Cleanup patch which removes the io_page_mask.  It fixes the reset on
some e1000 devices which is needed for clean kexec reboots.  The legacy
devices which broke with this patch (parallel port and PC speaker) have
now been fixed in Linus' tree.

Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-04-22 18:45:05 +10:00
Stephen Rothwell b239cbe957 [PATCH] powerpc: make ISA floppies work again
We used to assume that a DMA mapping request with a NULL dev was for
ISA DMA.  This assumption was broken at some point.  Now we explicitly
pass the detected ISA PCI device in the floppy setup.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-03-28 16:45:36 +11:00
John Rose 92eb4602eb [PATCH] powerpc: properly configure DDR/P5IOC children devs
The dynamic add path for PCI Host Bridges can fail to configure children
adapters under P5IOC controllers.  It fails to properly fixup bus/device
resources, and it fails to properly enable EEH.  Both of these steps
need to occur before any children devices are enabled in
pci_bus_add_devices().

Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-03-16 16:55:07 +11:00
Stephen Rothwell 9623b5d3d3 [PATCH] powerpc: small pci cleanups
pcibios_claim_one_bus is not needed on iSeries and phbs_remap_io can be
mode static.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-01-12 20:09:30 +11:00
linas af9deabeb0 [PATCH] PCI Hotplug/powerpc: module build break
The RPAPHP hoplug driver will not build as a module, because it calls
on a pcibios routine which is not exported. This exports the symbol.
Problem reported by Olaf Hering <olh@suse.de>

Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-01-11 14:47:30 +11:00
Benjamin Herrenschmidt 9d17a5c611 [PATCH] powerpc: Extended PCI config space
This adds back the call to pci_cfg_space_size() when building the PCI
tree from OF nodes that was commented out due to the function not being
exported by the PCI code. It's now exported, so let's use it.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-01-10 16:25:37 +11:00
Benjamin Herrenschmidt f2c4583a38 [PATCH] powerpc: pci_address_to_pio fix
This fixes pci_address_to_pio() to return an unsigned long (to be safe)
and fixes a bug in the implementation that caused it to return a bogus
IO port number

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-01-09 15:05:56 +11:00
Benjamin Herrenschmidt 1beb6a7d6c [PATCH] powerpc: Experimental support for new G5 Macs (#2)
This adds some very basic support for the new machines, including the
Quad G5 (tested), and other new dual core based machines and iMac G5
iSight (untested). This is still experimental !  There is no thermal
control yet, there is no proper handing of MSIs, etc.. but it
boots, I have all 4 cores up on my machine. Compared to the previous
version of this patch, this one adds DART IOMMU support for the U4
chipset and thus should work fine on setups with more than 2Gb of RAM.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-01-09 15:03:17 +11:00
Benjamin Herrenschmidt cc5d0189b9 [PATCH] powerpc: Remove device_node addrs/n_addr
The pre-parsed addrs/n_addrs fields in struct device_node are finally
gone. Remove the dodgy heuristics that did that parsing at boot and
remove the fields themselves since we now have a good replacement with
the new OF parsing code. This patch also fixes a bunch of drivers to use
the new code instead, so that at least pmac32, pseries, iseries and g5
defconfigs build.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-01-09 14:53:55 +11:00
Stephen Rothwell d4e4b3520c [PATCH] powerpc: fix for "Update OF address parsers"
This allows iSeries to build again.  It just moves pci_address_to_pio
outside the #ifdef CONFIG_PPC_MULTIPLATFORM.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-01-09 14:52:07 +11:00
Benjamin Herrenschmidt d2dd482bc1 [PATCH] powerpc: Update OF address parsers
This updates the OF address parsers to return the IO flags
indicating the type of address obtained. It also adds a PCI
call for converting physical addresses that hit IO space into
into IO tokens, and add routines that return the translated
addresses into struct resource

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-01-09 14:51:26 +11:00
Linas Vepstas facf07870b [PATCH] powerpc: make pcibios_claim_one_bus available to other code
22-rpaphp-eliminate-dupe-code.patch (parts)

The RPAPHP code contains two routines that appear to be gratuitous
copies of very similar pci code.  In particular,

   rpaphp_claim_resource ~~ pci_claim_resource
   rpadlpar_claim_one_bus == pcibios_claim_one_bus

This makes pcibios_claim_one_bus from arch/powerpc/kernel/pci_64.c
available to the RPAPHP code.

Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-01-09 14:51:08 +11:00
Benjamin Herrenschmidt 463ce0e103 [PATCH] powerpc: serial port discovery (#2)
This moves the discovery of legacy serial ports to a separate file,
makes it common to ppc32 and ppc64, and reworks it to use the new OF
address translators to get to the ports early. This new version can also
detect some PCI serial cards using legacy chips and will probably match
those discovered port with the default console choice.

Only ppc64 gets udbg still yet, unifying udbg isn't finished yet.

It also adds some speed-probing code to udbg so that the default console
can come up at the same speed it was set to by the firmware.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-01-09 14:49:50 +11:00
Paul Mackerras f8ef270596 powerpc: Merge pci.h
This involves some minor changes: a few unused functions that the
ppc32 pci.c provides are no longer declared here or exported;
pcibios_assign_all_busses now just refers to the pci_assign_all_buses
variable on both 32-bit and 64-bit; pcibios_scan_all_fns is now
just 0 instead of a function that always returns 0 on 64-bit.

Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-11-19 20:46:04 +11:00
Benjamin Herrenschmidt b5166cc252 [PATCH] powerpc: pci_64 fixes & cleanups
I discovered that in some cases (PowerMac for example) we wouldn't
properly map the PCI IO space on recent kernels. In addition, the code
for initializing PCI host bridges was scattered all over the place with
some duplication between platforms.

This patch fixes the problem and does a small cleanup by creating a
pcibios_alloc_controller() in pci_64.c that is similar to the one in
pci_32.c (just takes an additional device node argument) that takes care
of all the grunt allocation and initialisation work. It should work for
both boot time and dynamically allocated PHBs.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-11-16 13:29:46 +11:00
Michael Ellerman f9e4ec57c6 [PATCH] powerpc: More debugging fixups
Add a few more missing includes of udbg.h

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-11-16 13:29:40 +11:00
Paul Mackerras 7568cb4ef6 powerpc: Move most remaining ppc64 files over to arch/powerpc
Also deletes files in arch/ppc64 that are no longer used now that
we don't compile with ARCH=ppc64 any more.

Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-11-14 17:30:17 +11:00