Commit Graph

37 Commits

Author SHA1 Message Date
Vasanthakumar Thiagarajan b06af7a57d ath9k_hw: Read noise floor only for available chains for AR9003
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-04 14:05:17 -05:00
Felix Fietkau 55821324dc ath9k_hw: remove baseband rfsilent support
When rfkill is enabled, ath9k_hw unnecessarily configured the baseband to
turn off based on GPIO input, however that code was hardcoded to GPIO 0
instead of ah->rfkill_gpio.
Since ath9k uses software rfkill anyway, this code is completely unnecessary
and should be removed in case anything else ever uses GPIO 0.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20 14:49:48 -05:00
Vasanthakumar Thiagarajan 7e68b74668 ath9k_hw: Remove delay during regwrite of analog shift registers
This is not needed for AR9003.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-16 15:22:30 -05:00
Vasanthakumar Thiagarajan d9a2545ac7 ath9k: Read spur channel information from eeprom for AR9485
Also spur channel count and range is different for AR9485.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07 16:34:56 -05:00
Vasanthakumar Thiagarajan 85dd0921e6 ath9k_hw: Find chansel of AR_PHY_65NM_CH0_SYNTH7 for AR9485
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07 16:34:55 -05:00
Joe Perches 226afe68fd ath: Convert ath_print to ath_dbg
Remove ath/debug.h and the includes of these files.
Coalesce long formats.
Correct a few misspellings and missing "\n"s from these logging messages.
Remove unnecessary trailing space before a newline.
Remove ARRAY_SIZE casts, use printf type %zu

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07 16:34:48 -05:00
Mohammed Shafi Shajakhan ea066d5a91 ath9k: Add support for Adaptive Power Management
This feature is to mitigate the problem of certain 3
stream chips that exceed the PCIe power requirements.An EEPROM flag
controls which chips have APM enabled which is basically read from
miscellaneous configuration element of the EEPROM header.

This workaround will reduce power consumption by using 2 Tx chains for
Single and Double stream rates (5 GHz only).All self generated frames
(regardless of rate) are sent on 2 chains when this feature is
enabled(Chip Limitation).

Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Tested-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-30 13:49:13 -05:00
Joe Perches 07b2fa5a23 ath9k: Use static const
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

   text	   data	    bss	    dec	    hex	filename
  11161	     56	   2136	  13353	   3429	drivers/net/wireless/ath/ath9k/ar9003_paprd.o.new
  11167	     56	   2136	  13359	   342f	drivers/net/wireless/ath/ath9k/ar9003_paprd.o.old
  15428	     56	   3056	  18540	   486c	drivers/net/wireless/ath/ath9k/eeprom_4k.o.old
  15451	     56	   3056	  18563	   4883	drivers/net/wireless/ath/ath9k/eeprom_4k.o.new
  14087	     56	   2560	  16703	   413f	drivers/net/wireless/ath/ath9k/eeprom_9287.o.old
  14036	     56	   2560	  16652	   410c	drivers/net/wireless/ath/ath9k/eeprom_9287.o.new
  10041	     56	   2384	  12481	   30c1	drivers/net/wireless/ath/ath9k/ani.o.new
  10088	     56	   2384	  12528	   30f0	drivers/net/wireless/ath/ath9k/ani.o.old
   9316	   1580	   2304	  13200	   3390	drivers/net/wireless/ath/ath9k/htc_drv_init.o.new
   9316	   1580	   2304	  13200	   3390	drivers/net/wireless/ath/ath9k/htc_drv_init.o.old
  16483	     56	   3432	  19971	   4e03	drivers/net/wireless/ath/ath9k/ar9003_phy.o.new
  16517	     56	   3432	  20005	   4e25	drivers/net/wireless/ath/ath9k/ar9003_phy.o.old
  18221	    104	   2960	  21285	   5325	drivers/net/wireless/ath/ath9k/rc.o.old
  18203	    104	   2960	  21267	   5313	drivers/net/wireless/ath/ath9k/rc.o.new
  19985	     56	   4288	  24329	   5f09	drivers/net/wireless/ath/ath9k/eeprom_def.o.new
  20040	     56	   4288	  24384	   5f40	drivers/net/wireless/ath/ath9k/eeprom_def.o.old
  23997	     56	   4984	  29037	   716d	drivers/net/wireless/ath/ath9k/ar5008_phy.o.old
  23846	     56	   4984	  28886	   70d6	drivers/net/wireless/ath/ath9k/ar5008_phy.o.new
  24285	     56	   3184	  27525	   6b85	drivers/net/wireless/ath/ath9k/ar9003_eeprom.o.old
  24101	     56	   3184	  27341	   6acd	drivers/net/wireless/ath/ath9k/ar9003_eeprom.o.new
   6834	     56	   1032	   7922	   1ef2	drivers/net/wireless/ath/ath9k/ar9002_phy.o.old
   6780	     56	   1032	   7868	   1ebc	drivers/net/wireless/ath/ath9k/ar9002_phy.o.new
  36211	     64	   8624	  44899	   af63	drivers/net/wireless/ath/ath9k/hw.o.new
  36401	     64	   8624	  45089	   b021	drivers/net/wireless/ath/ath9k/hw.o.old
   9281	     56	   1496	  10833	   2a51	drivers/net/wireless/ath/ath9k/ar9003_calib.o.old
   9150	     56	   1496	  10702	   29ce	drivers/net/wireless/ath/ath9k/ar9003_calib.o.new

Use ARRAY_SIZE instead of a magic number.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:44 -05:00
Felix Fietkau c5d0855acf ath9k_hw: set default values for radar pulse detection
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:19:01 -05:00
Felix Fietkau 4e8c14e958 ath9k_hw: add a private op for configuring radar pulse detection
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:08 -05:00
Andreas Herrmann 7919a57bc6 bitops: Provide generic sign_extend32 function
This patch moves code out from wireless drivers where two different
functions are defined in three code locations for the same purpose and
provides a common function to sign extend a 32-bit value.

Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:27:04 -05:00
Felix Fietkau de40f316c0 ath9k_hw: extend ath9k_hw_set_txpowerlimit to test channel txpower
ath9k_hw_set_txpowerlimit gets an extra boolean parameter that - if set -
causes the rate txpower table and the regulatory limit to be calculated
and stored, without changing hardware registers.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:23:14 -05:00
Felix Fietkau b5bfc5683d ath9k_hw: move the cycle counter tracking to ath
Instead of keeping track of wraparound, clear the counters on every
access and keep separate deltas for ANI and later survey use.
Also moves the function for calculating the 'listen time' for ANI

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-11 15:04:20 -04:00
Felix Fietkau 093115b7fd ath9k_hw: clean up ANI state handling
ANI state is kept per channel, so instead of keeping an array of ANI states
with an arbitrary size of 255, move the ANI state into the channel struct.

Move some config settings that are not per-channel out of
the per-channel struct to save some memory.

With those changes, ath9k_ani_restart_old and ath9k_ani_restart_new can
be merged into a single function.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-06 16:30:39 -04:00
Felix Fietkau 9dbebc7fd0 ath9k_hw: merge codepaths that access the cycle counter registers
The cycle counters are used by ANI to determine the amount of time that the
radio spent not receiving or transmitting. They're also used for debugging
purposes if the baseband watchdog on AR9003 detects a lockup.
In the future, we want to use these counters to determine the medium utilization
and export this information via survey. For that, we need to make sure that
the counter is only accessed from one place, which also ensures that
wraparounds won't occur at inconvenient points in time.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-06 16:26:01 -04:00
Felix Fietkau b2ccc507b7 ath9k_hw: fix analog shift register writes on AR9003
Writes to the analog shift registers, which are issues by the initval
programming function, require a 100 usec delay (similar to AR9002,
but in a different register range).

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04 15:27:37 -04:00
Felix Fietkau 866b7780fc ath9k_hw: fix invalid extension channel noisefloor readings in HT20
When the hardware is configured in HT20 mode, noise floor readings for
the extension channel often return invalid values, which keep the
values in the NF history buffer at the hardware-specific maximum limit.
Fix this by discarding the extension channel values when in HT20 mode.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-07-26 15:32:42 -04:00
Felix Fietkau bbacee13f4 ath9k: merge noisefloor load implementations
AR5008+ and AR9003 currently use two separate implementations of the
ath9k_hw_loadnf function. There are three main differences:

 - PHY registers for AR9003 are different
 - AR9003 always uses 3 chains, earlier versions are more selective
 - The AR9003 variant contains a fix for NF load timeouts

This patch merges the two implementations into one, storing the
register array in the ath_hw struct. The fix for NF load timeouts is
not just relevant for AR9003, but also important for earlier hardware,
so it's better to just keep one common implementation.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-07-12 16:05:39 -04:00
Felix Fietkau 54bd5006b0 ath9k_hw: clean up the noise floor calibration code to reduce code duplication
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-07-02 13:44:37 -04:00
Felix Fietkau f2552e2837 ath9k_hw: sanitize noise floor values properly on all chips
This refactors the noise floor range checks to make them generic,
and adds proper ranges for each supported chip type.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-07-02 13:44:36 -04:00
Luis R. Rodriguez 644c78c95a ath9k_hw: reduce delay on programming INI on AR9003
All AR9003 devices are PCI-E only, the extra delay here
is not required and only reduces the delay for loading
the initial register values by at least 14ms.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-14 15:39:30 -04:00
Luis R. Rodriguez e36b27aff1 ath9k: add new ANI implementation for AR9003
This adds support for ANI for AR9003. The implementation for
ANI for AR9003 is slightly different than the one used for
the older chipset families. It can technically be used for
the older families as well but this is not yet fully tested
so we only enable the new ANI for the AR5008, AR9001 and AR9002
families with a module parameter, force_new_ani.

The old ANI implementation is left intact.

Details of the new ANI implemention:

  * ANI adjustment logic is now table driven so that each ANI level
    setting is parameterized. This makes adjustments much more
    deterministic than the old procedure based logic and allows
    adjustments to be made incrementally to several parameters per
    level.

  * ANI register settings are now relative to INI values; so ANI
    param zero level == INI value. Appropriate floor and ceiling
    values are obeyed when adjustments are combined with INI values.

  * ANI processing is done once per second rather that every 100ms.
    The poll interval is now a set upon hardware initialization and
    can be picked up by the core driver.

  * OFDM error and CCK error processing are made in a round robin
    fashion rather than allowing all OFDM adjustments to be made
    before CCK adjustments.

  * ANI adjusts MRC CCK off in the presence of high CCK errors

  * When adjusting spur immunity (SI) and OFDM weak signal detection,
    ANI now sets register values for the extension channel too

  * When adjusting FIR step (ST), ANI now sets register for FIR step
    low too

  * FIR step adjustments now allow for an extra level of immunity for
    extremely noisy environments

  * The old Noise immunity setting (NI), which changes coarse low, size
    desired, etc have been removed. Changing these settings could affect
    up RIFS RX as well.

  * CCK weak signal adjustment is no longer used

  * ANI no longer enables phy error interrupts; in all cases phy hw
    counting registers are used instead

  * The phy error count (overflow) interrupts are also no longer used
    for ANI adjustments. All ANI adjustments are made via the polling
    routine and no adjustments are possible in the ISR context anymore

  * A history settings buffer is now correctly used for each channel;
    channel settings are initialized with the defaults but later
    changes are restored when returning back to that channel

  * When scanning, ANI is disabled settings are returned to (INI) defaults.

  * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for
    low/high water marks, providing increased stability/hysteresis when
    changing levels.

  * Similarly CCK phy error thresholds are now 300 & 600 (errors/second)

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-14 15:39:29 -04:00
Luis R. Rodriguez aea702b70a ath9k_hw: add support for the AR9003 baseband watchdog
The baseband watchdog will monitor blocks of the baseband
through timers and will issue an interrupt when things are
detected to be stalled. It is only available on the AR9003
family.

Cc: Sam Ng <sam.ng@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Cc: Cliff Holden <cliff.holden@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-02 16:13:00 -04:00
Felix Fietkau 5d5d44d914 ath9k_hw: fix noisefloor timeout handling on AR9003
When the noisefloor calibration times out, do not load -50 into
the registers, since this might cause rx issues. Instead, leave
enough time for the noise floor calibration to complete until
the next check.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:20 -04:00
Felix Fietkau 6b42e8d03b ath9k_hw: fix fast clock handling for 5GHz channels
Combine multiple checks that were supposed to check for the same
conditions, but didn't. Always enable fast PLL clock on AR9280 2.0

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:18 -04:00
Felix Fietkau 14bc110463 ath9k_hw: fix pll clock setting for 5ghz on AR9003
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:16 -04:00
Luis R. Rodriguez 1547da37db ath9k_hw: add OFDM spur mitigation for AR9003
We add this now as OFDM spur mitigation required accessing
the EEPROM for the AR9003 devices.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16 15:43:38 -04:00
Luis R. Rodriguez df23acaa5d ath9k_hw: complete AR9003 calibration
This goes with some new shiny TX IQ calibration that AR9003
hardware family supports.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16 15:43:35 -04:00
Felix Fietkau 641d99217f ath9k_hw: Split out the function for reading the noise floor
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16 15:43:27 -04:00
Luis R. Rodriguez af914a9ffd ath9k_hw: add all the AR9003 PHY callbacks
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16 15:43:25 -04:00
Felix Fietkau c16fcb49b3 ath9k_hw: Split off ANI control to the PHY ops
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16 15:43:25 -04:00
Luis R. Rodriguez cffb5e49a1 ath9k_hw: add helpers for processing the AR9003 INI
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16 15:43:24 -04:00
Felix Fietkau ca37555407 ath9k_hw: Implement spur mitigation on AR9003
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16 15:43:24 -04:00
Felix Fietkau 317d33280c ath9k_hw: Implement PLL control on AR9003
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16 15:43:23 -04:00
Felix Fietkau f7abf0c195 ath9k_hw: Set the channel on AR9003
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16 15:43:23 -04:00
Felix Fietkau da6f1d7f5f ath9k_hw: Add AR9003 PHY register definitions
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16 15:43:23 -04:00
Luis R. Rodriguez 8525f2801d ath9k_hw: Add AR9003 PHY support
This add stubs for PHY support for the AR9003 hardware family.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16 15:43:20 -04:00