These nodes are required so that the flow controller driver can obtain
the I/O memory region from device tree rather than hard-coding it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
Add efuse and apbmisc bindings for Tegra20, Tegra30, Tegra114 and
Tegra124.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add new properties to all of the Tegra PHYs that are now required
according to the binding.
In order to stay compatible with old device trees, the USB drivers
will still function without these reset properties but with the old,
potentially buggy behaviour.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This enables:
* host1x and eDP support on Tegra124.
* LCD panel support for a few Tegra20 devices and Venice2.
* Enables power down, SPI flash, and USB on Venice2.
* Documents which Dalmore revision is supported.
* Adds an I2C bus mux to Cardhu.
Additionally, Tegra124 is converted to use #address-cells=<2> since the
HW suports more than 32-bits of address space, and various cleanups are
included.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJTGiq1AAoJEMzrak5tbycxM48P/17/DY8vXhIGs7/BW0StsMOV
kr333+12dxBQB0kftHoOtTv4/WutV4jjKAJm+pRBdu/yJ2on9FKKu11Q3r5EjI/B
9GDk5JSyHRkSIFdzPx4f0QskklmDqJuXD+MNfiQIGC2pv/WQotLUd6rJLcVWE/bk
8oVFg4b1kAFB2RKqwMywOMPh3X5A6xQKz/yCNLbEYsQXk9p9Iri/nX0Wq6dNVVP/
qjbll69anJ4IjhCJO4ndrGPWob2GTQpB5a5YGl+0sSZGUEzX/dsCJRgKRrP/JjeC
mZDWEqRTkqs2g8ZdNdseqMEgW9aksGAT57UCHbVMEd+1szY9RXB2kbvlPdUaU2XL
oPQpF0dvh3/i/227vvgI8dK4Vo56TPvVWdyztZS1mHL59ouAR6CajRgAQP4Ra6Ug
4qNJt/CKqm1lRO4eDXgDwt7zL+vP3bL4Mpcc7mN3d45iTz4uRN0KFoUbz/B++Mii
20+Y5Qn1mZr6CukPcUcT1bivQR42DPQslidaEruaamoBg6Fnn+yNr3KhKcRwS4Xs
4LuW6D4Bi+DIFwztCtQYf7pkuVHziQGUc1LnAQPqXYurMKVvnjbSjSXCxUsclkUT
W6gaqZ9QKdjlELuuz97eO866uodZpHNZVxBlnuSaTpHZexRIkLWRHTUUFPtlL+AR
MJW+8QCUrR08we1WmjlC
=cniI
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.15-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: device tree changes for 3.15" from Stephen Warren:
This enables:
- host1x and eDP support on Tegra124.
- LCD panel support for a few Tegra20 devices and Venice2.
- Enables power down, SPI flash, and USB on Venice2.
- Documents which Dalmore revision is supported.
- Adds an I2C bus mux to Cardhu.
Additionally, Tegra124 is converted to use #address-cells=<2> since the
HW suports more than 32-bits of address space, and various cleanups are
included.
* tag 'tegra-for-3.15-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (21 commits)
ARM: dts: tegra: add PCIe interrupt mapping properties
ARM: tegra: use 2 address cells for Tegra124 DT
ARM: tegra: Rename as3722 node to pmic
ARM: tegra: Fix whitespace around '='
ARM: tegra: Enable USB on Venice2
ARM: tegra: Add Tegra124 USB support
ARM: tegra: Enable eDP for Venice2
ARM: tegra: Add Tegra124 eDP support
ARM: tegra: Add Tegra124 host1x support
ARM: tegra: Hook up SDMMC3 power-supply on Venice2
ARM: tegra: Overhaul Venice2 regulators
ARM: tegra: Combine VBUS enable pins into one node
ARM: tegra: Use "disabled" for status property
ARM: tegra: add SPI flash to Venice2 DT
ARM: tegra: enable PCA9546 on Cardhu
ARM: tegra: enable LCD panel on Ventana
ARM: tegra: enable LCD panel on Seaboard
ARM: tegra: add system-power-controller property for PMIC node
ARM: tegra: document which Dalmore revisions are supported
ARM: tegra: Properly sort clocks property
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Those are defined by the common PCI binding.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The number of the head specifies the index of the display controller
unit and is required to properly configure outputs so that they receive
video data from the correct source.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Use Tegra pinconrol dt-binding macro to set the values of different pinmux
properties of Tegra20 platforms.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
DT node names should include a unit address iff the node has a reg
property. For Tegra DTs at least, we were previously applying a different
rule, namely that node names only needed to include a unit address if it
was required to make the node name unique. Consequently, many unit
addresses are missing. Add them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Now that all Tegra drivers have been converted to use DMA APIs which
retrieve DMA channel information from standard DMA DT properties, we can
remove all the legacy DT DMA-related properties.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Now that all Tegra drivers have been converted to use the common reset
framework, we can remove all the legacy DT clocks/clock-names entries for
"clocks" that were only used with the old custom Tegra module reset API.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
This patch switches the Tegra DT files to use the standard DMA DT bindings
rather than custom properties. Note that the legacy properties are not yet
removed; the drivers must be updated to use the new properties first.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
An earlier patch updated the Tegra DT bindings to require resets and
reset-names properties to be filled in. This patch updates the DT files
to include those properties.
Note that any legacy clocks and clock-names entries that are replaced by
reset properties are not yet removed; the drivers must be updated to use
the new resets and reset-names properties first.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Many of the Tegra DT binding documents say nothing about the clocks or
clock-names properties, yet those are present and required in DT files.
This patch simply updates the documentation file to match the implicit
definition of the binding, based on real-world DT content.
All Tegra bindings that mention clocks are updated to have consistent
wording and formatting of the clock-related properties.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on various
platforms as support gets added. Some of the bigger changes are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for 4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1GuI
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on
various platforms as support gets added. Some of the bigger changes
are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for
4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (177 commits)
dts: Rename DW APB timer compatible strings
dts: Deprecate ALTR as a vendor prefix
of: add vendor prefix for Altera Corp.
ARM: at91/dt: sam9x5ek: add sound configuration
ARM: at91/dt: sam9x5ek: enable SSC
ARM: at91/dt: sam9x5ek: add WM8731 codec
ARM: at91/dt: sam9x5: add SSC DMA parameters
ARM: at91/dt: add at91rm9200 PQFP package version
ARM: at91: at91rm9200: set default mmc0 pinctrl-names
ARM: at91: at91sam9n12: correct pin number of gpio-key
ARM: at91: at91sam9n12: add qt1070 support
ARM: at91: at91sam9n12: add pinctrl of TWI
ARM: at91: Add PMU support for sama5d3
ARM: at91: at91sam9260: add missing pinctrl-names on mmc
ARM: tegra: configure power off for Dalmore
ARM: DT: binding fixup to align with vendor-prefixes.txt (DT)
ARM: dts: add sdio blocks to bcm28155-ap board
ARM: dts: align sdio numbers to HW definition
ARM: sun7i: Add Olimex A20-Olinuxino-Micro support
ARM: sun7i: Add Allwinner A20 DTSI
...
Instead of evenly splitting the 512 MiB area between prefetchable and
non-prefetchable memory spaces, increase the prefetchable memory space
to 384 MiB while at the same time decreasing the non-prefetchable memory
space to 128 MiB. This is a more useful default as most PCIe devices
require more prefetchable than non-prefetchable memory.
Signed-off-by: Jay Agarwal <jagarwal@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add the top-level pcie-controller node for the Tegra20 SoC. Tegra20 has
two root ports that can use different lane layouts.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
[swarren: split DT changes into a separate patch from the main driver]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch changes the Tegra20 USB PHY nodes to use the UTMI configuration
parameter names as specified in the device tree binding documentation
after patch "ARM: tegra: finalize USB EHCI and PHY bindings".
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the Tegra20 CAR binding header (tegra20-car.h) to replace magic
numbers in the device tree. For example,
- clocks = <&tegra_car 28>;
+ clocks = <&tegra_car CLK_HOST1X>;
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
[swarren, updated since tegra20-car.h moved for consistency]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use TEGRA_GPIO() macro to name all GPIOs referenced by GPIO properties,
and some interrupts properties. Use standard GPIO flag defines too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Replace /include/ (dtc) with #include (C pre-processor) for all Tegra DT
files, so that gcc -E handles the entire include tree, and hence any of
those files can #include some other file e.g. for constant definitions.
This allows future use of #defines and header files in order to define
names for various constants, such as the IDs and flags in GPIO
specifiers. Use of those features will increase the readability of the
device tree files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch updates all Tegra board files so that they contain all the
properties required by the updated USB DT binding. Note that this patch
only adds the new properties and does not yet remove the old properties,
in order to maintain bisectability. The old properties will be removed
once the driver has been updated to assume the new bindings.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
[swarren: fixed some newly added regulator-name properties to better
match schematic, avoided duplicate regulator-name on Whistler.]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This branch contains the majority of the device tree changes for Tegra.
Highlights include:
* Many changes for Tegra114, and the Dalmore board, to enable pinctrl,
SDHCI/MMC, PWM, DMA, I2C, KBC, SPI, battery, regulators.
* Adding or enabling suspend wakeup sources on many boards, and adding
suspend timing parameters, to support the system suspend patches.
* Adding clocks to the audio-related nodes, so that in 3.11, the audio
driver can pull these clocks from device tree rather than hard-coding
clock names.
* Some small DT fixes/cleanup.
This branch is based on the previous clk pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=avad
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.10-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt2
From Stephen Warren <swarren@wwwdotorg.org>:
ARM: tegra: device tree changes
This branch contains the majority of the device tree changes for Tegra.
Highlights include:
* Many changes for Tegra114, and the Dalmore board, to enable pinctrl,
SDHCI/MMC, PWM, DMA, I2C, KBC, SPI, battery, regulators.
* Adding or enabling suspend wakeup sources on many boards, and adding
suspend timing parameters, to support the system suspend patches.
* Adding clocks to the audio-related nodes, so that in 3.11, the audio
driver can pull these clocks from device tree rather than hard-coding
clock names.
* Some small DT fixes/cleanup.
This branch is based on the previous clk pull request.
* tag 'tegra-for-3.10-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (25 commits)
clk: tegra: Fix cdev1 and cdev2 IDs
ARM: dts: tegra: add the PM configurations of PMC
ARM: tegra: add non-removable and keep-power-in-suspend property for MMC
ARM: tegra: whistler: add wakeup source for KBC
ARM: tegra: add power gpio keys to DT
ARM: tegra: keep power on to SD slot on Dalmore
ARM: tegra: add clocks property to AC'97 sound nodes
ARM: tegra: add clocks property to sound nodes
ARM: tegra: dalmore: add fixed regulator node
ARM: tegra: dalmore: add TPS65090 node
ARM: tegra: dalmore: add cpu regulator node
ARM: tegra: Add sbs-battery node to Dalmore
ARM: tegra: add DT binding for i2c-tegra
ARM: tegra: add SPI nodes to Tegra114 DT
ARM: tegra: add KBC nodes to Tegra114 DT
ARM: tegra: add aliases and DMA requestor for serial nodes of Tegra114
ARM: tegra: add I2C nodes to Tegra114 DT
ARM: tegra: add APB DMA nodes to Tegra114 DT
ARM: tegra: add PWM nodes to Tegra114 DT
ARM: tegra: fix the status of PWM DT nodes
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Correct IDs for cdev1 and cdev2 are 94 and 93 respectively.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: split into separate driver and device-tree patches]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
We should be defining the PWM nodes with status as "disabled" in the
chip-specific dtsi file, since we don't know whether specific boards
will use the PWM or not. This patch fixes the PWM node status for
Tegra20 and Tegra30.
Also fixed the one user of PWM, which is the Tegra20 medcom-wide board,
so that PWM is set to "okay" in the board-specific dts file.
Signed-off-by: Andrew Chew <achew@nvidia.com>
[swarren: in medcom-wide: fixed node sort order, removed duplicate pwm:
label, fixed syntax error]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The USB PHY nodes are all grouped together rather than being sorted based
on reg address like all other nodes fix this.
I apologize for the churn; I should have noticed this during review of the
patches that caused this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Fix typo on register address of slink3 controller where register
address is wrongly set as 0x7000d480 but it is 0x7000d800.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The new clockframework introduced DT IDs for each clock. To be able to remove
the device registrations, this driver needs to be updated to use the DT IDs.
Note that the actual removal of the clk_register_clkdev() calls will be done
in a later series.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
As DT support for clocks and smp_twd is enabled, add clock entry
for smp_twd clock to DT.
This fixes the following error while booting the kernel:
smp_twd: clock not found -2
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: include kernel log spew that this fixes]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently, the serial nodes define both a clock-frequency and a clocks
property. We should not provide both, since they might conflict.
In practice, this also causes problems since the of_serial driver uses
the clock-frequency property in preference to the clocks property, and
hence doesn't clk_prepare_enable() the clock, which may then leave it
with no known users, and hence the common clock framework will disable
it, thus breaking the port, which is usually the console.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use functional name for DT entry instead of h/w name.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
No Tegra20 Platform is running PLL_P at another rate than 216MHz, nor is
any using any other PLL as UART source clock. Move attribute into SoC
level dtsi file to slim down board DT files.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra SoCs have the matrix keyboard controller which
supports 16x8 type of matrix. The number of rows and columns
are configurable.
Add DT entry for KBC controller.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: added clocks property]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This ensures nodes are sorted in order of reg address. This makes it
easier to compare against e.g. the U-Boot device trees, and is simply
consistent and clean.
While we're at it, remove the unit address from the cache-controller
node name, since it's unique without it.
Reported-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add APB DMA requestor and serial aliases for serial controller.
There will be two serial driver i.e. 8250 based simple serial driver
and APB DMA based serial driver for higher baudrate and performace.
The simple serial driver get enabled with compatible nvidia,tegra20-uart
and APB DMA based driver will get enabled with compatible
nvidia,tegra20-hsuart.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The patch to add USB PHY nodes to device tree was written before Tegra
supported the clocks property in device tree. Now that it does, add the
required clocks properties to these nodes.
This will allow all clk_get_sys() calls in tegra_usb_phy.c to be replaced
by clk_get(phy->dev, clock_name), as part of converting the PHY driver to
a platform driver.
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add DT nodes for Tegra USB PHY along with related documentation.
Also added a phandle property to controller DT node, for referring
to connected PHY instance.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
As Tegra USB host driver is using instance number for resetting
PORT0 twice, adding a new DT property for handling this.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra20 CAR (Clock And Reset) Controller controls most aspects of
most clocks within Tegra20. The device tree binding models this as a
single monolithic clock provider, which exports many clocks. This reduces
the number of nodes needed in device tree to represent these clocks.
This binding is only useful for Tegra20; the set of clocks that exists on
Tegra30 is sufficiently different to merit its own binding.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
[pgaikwad: Added mux clk ids and sorted CAR node]
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add CPU node for Tegra20.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This will allow timer.c to use twd_local_timer_of_register(), and
hence not need to hard-code the TWD address or IRQ.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra RTC maintains seconds and milliseconds counters, and five alarm
registers. The alarms and other interrupts may wake the system from
low-power state.
Define a DT binding for this HW module, and add the module into the Tegra
device tree files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Thierry Reding