If VDDA != VDDIO and any of them is greater than 3.1V, charge pump
source can be assigned automatically [1].
[1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20190719100524.23300-7-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To enable "zero cross detect" for ADC/HP, change
HP_ZCD_EN/ADC_ZCD_EN bits only instead of writing the whole
CHIP_ANA_CTRL register.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20190719100524.23300-6-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This control mute/unmute the ADC input of SGTL5000
using its CHIP_ANA_CTRL register.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20190719100524.23300-5-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SGTL5000_SMALL_POP is a bit mask, not a value. Usage of
correct definition makes device probing code more clear.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20190719100524.23300-4-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
VAG power control is improved to fit the manual [1]. This patch fixes as
minimum one bug: if customer muxes Headphone to Line-In right after boot,
the VAG power remains off that leads to poor sound quality from line-in.
I.e. after boot:
- Connect sound source to Line-In jack;
- Connect headphone to HP jack;
- Run following commands:
$ amixer set 'Headphone' 80%
$ amixer set 'Headphone Mux' LINE_IN
Change VAG power on/off control according to the following algorithm:
- turn VAG power ON on the 1st incoming event.
- keep it ON if there is any active VAG consumer (ADC/DAC/HP/Line-In).
- turn VAG power OFF when there is the latest consumer's pre-down event
come.
- always delay after VAG power OFF to avoid pop.
- delay after VAG power ON if the initiative consumer is Line-In, this
prevents pop during line-in muxing.
According to the data sheet [1], to avoid any pops/clicks,
the outputs should be muted during input/output
routing changes.
[1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf
Cc: stable@vger.kernel.org
Fixes: 9b34e6cc3b ("ASoC: Add Freescale SGTL5000 codec support")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20190719100524.23300-3-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch introduces "sclk-strength" property to allow SCLK pad drive
strength to be changed via device tree.
When running playback test on LS1028ARDB, Tx Frame sync error interrupt
will occur sometimes. Some noises also exist. After changing SCLK pad
drive strength to the maximum value, the issues are gone.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the case where lo_vag <= SGTL5000_LINE_OUT_GND_BASE, lo_vag
is set to zero and later vol_quot is computed by dividing by
lo_vag causing a division by zero error. Fix this by avoiding
a zero division and set vol_quot to zero in this specific case
so that the lowest setting for i is correctly set.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable 5-band graphic equalizer which allows manipulation of
gain in range -11.75dB to 12dB for 5 specific sound bands:
115Hz, 330Hz, 990Hz, 3000Hz, 9900Hz.
Signed-off-by: Michal Oleszczyk <oleszczyk.m@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add mux for choosing DAC source: ADC, I2S or DAP. DAP - digital
audio processing block. Moreover create choosing mux for DAP main
source (ADC or I2S) and DAP mixer source (ADC or I2S). Mixer block
allows summing DAP main and mixer sources togheter with defined
volumes.
Signed-off-by: Michal Oleszczyk <oleszczyk.m@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 8419caa727 ("ASoC: sgtl5000: Do not disable regulators in
SND_SOC_BIAS_OFF") causes the sgtl5000 to fail after a suspend/resume
sequence:
Playing WAVE '/media/a2002011001-e02.wav' : Signed 16 bit Little
Endian, Rate 44100 Hz, Stereo
aplay: pcm_write:2051: write error: Input/output error
The problem is caused by the fact that the aforementioned commit
dropped the cache handling, so re-introduce the register map
resync to fix the problem.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Current implementation mute codec in global way (DAC block).
That means when user routes sound not from I2S but from
AUX source (LINE_IN) it also will be muted by alsa core.
This should not happen.
Signed-off-by: Michal Oleszczyk <oleszczyk.m@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "check ER1" message is not very clear about its meaning.
Improve it a bit by referring to it as "ER1 erratum" so that it
becomes clearer that ER1 references to a SGTL5000 erratum.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the MCLK is not yet available when the codec is probed, probe
deferral will happen and in this case we should not print an
error message.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare snd_soc_codec_driver structures as const as they are only passed
as an argument to the function snd_soc_register_codec. This argument is
of type const, so declare the structures with this property as const.
In file codecs/sn95031.c, snd_soc_codec_driver structure is also used in
a copy operation along with getting passed to snd_soc_register_codec.
So, it can be made const too.
Done using Coccinelle:
@match disable optional_qualifier@
identifier s;
position p;
@@
static struct snd_soc_codec_driver s@p={...};
@good1@
identifier match.s;
position p;
@@
snd_soc_register_codec(...,&s@p,...)
@bad@
identifier match.s;
position p!={match.p,good1.p};
@@
s@p
@depends on !bad disable optional_qualifier@
identifier match.s;
@@
static
+const
struct snd_soc_codec_driver s={...};
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit a729526720 ("ASoC: sgtl5000: add avc support") the
following kernel crash happens after running a 'reboot' command:
ALSA: Storing mixer settings...
[ 20.031604] Unable to handle kernel paging request at virtual address fffffffe
[ 20.039268] pgd = de2a0000
[ 20.041999] [fffffffe] *pgd=8fffd861, *pte=00000000, *ppte=00000000
[ 20.048387] Internal error: Oops: 80000007 [#1] SMP ARM
The function that takes a kcontrol parameter and returns the
codec that registered the control is snd_soc_kcontrol_codec(),
so use the correct function to fix the problem.
Fixes: a729526720 ("ASoC: sgtl5000: add avc support")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The sgtl5000 features an automatic volume control block (AVC), which
reduces loud signals and amplifies low level signals for easier
listening. This patch adds support for this AVC block to the driver.
Apart from the "AVC Switch" control which enables the block following
controls for the configuration of AVC are added:
+ AVC Threshold Volume: threshold where audio is compressed when
the measured level is above or expanded when below
+ AVC Max Gain Volume: maximum gain which can be applied when
the measured audio level is below threshold
+ AVC Hard Limiter Switch: when enabled the signal is limited to
the programmed threshold.
+ AVC Integrator Response: response time of the integrator
The AVC block is enabled and configured using the DAP_AVC_CTRL and
DAP_AVC_THRESHOLD registers.
Following 2 checkpatch.pl strict checks are ignored because the
indentation style is different for the struct snd_kcontrol_new
definition:
patch:147: CHECK: Alignment should match open parenthesis
patch:150: CHECK: Alignment should match open parenthesis
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce the "lrclk-strength" property to allow LRCLK pad drive strength
to be changed via device tree.
When running a stress playback loop test on a mx6dl wandboard channel
swap can be noticed on about 10% of the times.
While debugging this issue I noticed that when probing the SGTL5000
LRCLK pin with the scope the swap did not happen. After removing
the probe the swap started to happen again.
After changing the LRCLK pad drive strength to the maximum value the
issue is gone.
Same fix works on a mx6dl Colibri board as well.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These controls mute/unmute the LINEOUT and headphone outputs of SGTL5000
using its CHIP_ANA_CTRL register.
Signed-off-by: Richard Leitner <dev@g0hl1n.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
codec driver and component driver has duplicated callback functions,
and codec side functions are just copied to component side when
register timing. This was quick-hack, but no longer needed.
This patch moves these functions from codec driver to component driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This controls the volume for the line out pins of SGTL5000.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Disabling the SGTL5000 through regulators would certainly save more
power than simply disabling the reference voltages as described in the
data sheet, but won't properly restore things on resume.
This driver does not support active regulators. So we simply disable the
reference bias currents.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To handle the soft reboot case, the internal PLL must be
disabled in SGTL5000_CHIP_CLK_CTRL before clearing bits
SGTL5000_VCOAMP_POWERUP and SGTL5000_PLL_POWERUP in
register SGTL5000_CHIP_ANA_POWER.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initialize CHIP_ANA_POWER to match power on defaults, which disables
ADC, DAC, and charge pumps.
In the process, remove references to the following register/bitfields
from the sgtl5000_set_power_regs routine:
CHIP_ANA_POWER/LINREG_SIMPLE_POWERUP and
CHIP_LINREG_CTRL/LINREG_VDD_MASK
And remove CHIP_ANA_POWER and CHIP_LINREG_CTRL from the set of default
registers so they don't get clobbered by sgtl5000_fill_defaults().
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If an error occurs writing defaults, produce an error message but
continue writing other registers. The failure of a single write should
not cause catastrophic device failure.
In at least one occurrence, I2C writes of CHIP_ANA_POWER were nacked,
though continuing allowed the device to operate properly.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulator support on SGTL5000 is broken because the VDDIO and
VDDA and VDDD should be powered on before enabling MCLK as
shown in Figure 4 of [1]. This requires moving control of the
regulators from the codec block to the I2C block of the driver.
The bulk of this patch consists of swapping the codec device with
the i2c client. The new field num_supplies in struct sgtl5000_priv
is used instead of ARRAY_SIZE(supplies) to handle the special case
when the internal LDO is used instead of external VDDD.
Note that ER1 in the SGTL5000 Errata document [2] suggests that
all designs should use external VDDD.
Since the internal LDO can only be enabled after I2C is available,
there's no benefit in treating it as a regulator, so this patch
removes the regulator structure surrounding it.
Instead, a single block of code in sgtl5000_i2c_probe() performs
the initialization sequence in section 2.2.1.1 of [3] and page
26 of [1].
References:
[1] SGTL5000 data sheet
http://cache.nxp.com/files/analog/doc/data_sheet/SGTL5000.pdf
[2] SGTL5000 errata
http://cache.nxp.com/files/analog/doc/errata/SGTL5000ER.pdf
[3] SGTL5000 Initialization and programming app note
http://cache.nxp.com/files/analog/doc/app_note/AN3663.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All new designs should use external VDDD according to official
documentation. See ER1 in errata sheet:
http://cache.nxp.com/files/analog/doc/errata/SGTL5000ER.pdf
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When power up, a "pop" is heard on line-in and mic-in.
An analysis of the PCM shows it lasts ~400ms
and looks like a filter response.
VAG power up should be delayed by 400ms as VAG power down is.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@veo-labs.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All drivers have the same line at the end of the set_bias_level callback to
update the bias_level state. Move this update into
snd_soc_dapm_force_bias_level() and remove them from the drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently LO_VOL_* stays at it's default (0x4 each) but this should be
calculated after setting VAG_VAL and LO_VAGCNTRL.
LO_VOL_* = 40 * log10(VAG_VAL / LO_VAGCNTRL) + 15
To avoid the log10 operation a table for all valid register values is
precalculated which contains the corresponding value
(VAG_VAL * 100 / LO_VAGCNTRL).
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a preparation for calculating lo_vol which needs both vag
and lo_vag.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SGTL5000_CHIP_ANA_POWER register is cached. Update the cached
value instead of writing it directly.
Patch inspired by Russell King's more colorful remarks in this
patch:
https://github.com/SolidRun/linux-imx6-3.14/commit/dd4bf6a
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
To quote from section 1.3.1 of the data sheet:
The SGTL5000 has an internal reset that is deasserted
8 SYS_MCLK cycles after all power rails have been brought
up. After this time, communication can start
...
1.0us represents 8 SYS_MCLK cycles at the minimum 8.0 MHz SYS_MCLK.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Shift the I2S mode value by the necessary amount before writing the
registers. This makes Right Justified and PCM mode work in addition to
the default Left Justified mode.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Oleksandr Suvorov