Andy reported pch_gbe triggered "NETDEV WATCHDOG" errors.
May 11 11:06:09 kontron kernel: WARNING: at net/sched/sch_generic.c:261
dev_watchdog+0x1ec/0x200() (Not tainted)
May 11 11:06:09 kontron kernel: Hardware name: N/A
May 11 11:06:09 kontron kernel: NETDEV WATCHDOG: eth0 (pch_gbe):
transmit queue 0 timed out
It seems pch_gbe has a racy tx path (races with TX completion path)
Remove tx_queue_lock lock since it has no purpose, we must use tx_lock
instead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andy Cress <andy.cress@us.kontron.com>
Tested-by: Andy Cress <andy.cress@us.kontron.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset logic after a Rx FIFO overrun will clear the programmed
multicast addresses. This patch fixes the issue by reprogramming the
registers after the reset.
The commit eefc48b ("pch_gbe: reprogram multicast address register on
reset") tried to fix this problem, but it introduces unnecessary
codes. In fact, all multicast addresses have been saved in netdev->mc,
So we can call pch_gbe_set_multi() directly after reset_hw and
reset_rx.
This commit kills 50+ line codes
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If I understand correct, NETIF_F_IP_CSUM only means the hardware
will compute the TCP/UDP checksum, IP checksum is always computed
in software
So as a workround of hardware unable to compute small packages
checksum, do not need to compute IP header checksum.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCH_GBE_ETH_ALEN is equal to ETH_ALEN, so we can replace it with
ETH_ALEN.
If they are not equal, it must be a bug, since this is ethernet,
and the address has been already stored to mc_addr_list as ETH_ALEN
bytes when call pch_gbe_mac_mc_addr_list_update.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The time stamping code in this driver appears to have been copied from
the ixp4xx_eth.c driver, including this timing comment. I had actually
measured the time stamp delay on an IXP425, but I really doubt that this
value also applies here.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes code which needlessly ran the BPF twice per
packet. Instead, we just run the classifier once and test
whether the packet is any kind of PTP event message.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the driver so that multicast PTP event messages can
be recognized by the hardware time stamping unit. The station address
register must be set according to the desired transport type.
[ RC - Rebased Takahiro's changes and wrote a commit message
explaining the changes. ]
Signed-off-by: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch clears up a few coding style issues:
- Makes two function definitions a bit nicer looking.
- Remove unneeded parentheses.
- Simplify macros for register bits.
[ RC - Rebased Takahiro's changes and wrote a commit message
explaining the changes. ]
Signed-off-by: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code in phc_gbe_main will need to call this method in order to set the
station address register according to the receive time stamping filter.
[ RC - Rebased Takahiro's changes and wrote a commit message
explaining the changes. ]
Signed-off-by: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset logic after a Rx FIFO overrun will clear the programmed
multicast addresses. This patch fixes the issue by reprogramming the
registers after the reset.
[ RC - Rebased Takahiro's changes and wrote a commit message
explaining the changes. ]
Signed-off-by: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes logic surrounding the test of the
transmit time stamping flag more readable.
[ RC - Rebased Takahiro's changes and wrote a commit message
explaining the changes. ]
Signed-off-by: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the helper functions that give the transmit and
receive time stamps to return nanoseconds, instead of arbitrary clock
ticks.
[ RC - Rebased Takahiro's changes and wrote a commit message
explaining the changes. ]
Signed-off-by: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supports EG20T ptp clock in the driver
Changes e-mail address.
Adds number.
Signed-off-by: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/tg3.c
Conflicts in the statistics regression bug fix from 'net',
but happily Matt Carlson originally posted the fix against
'net-next' so I used that to resolve this.
Signed-off-by: David S. Miller <davem@davemloft.net>
pch_gbe_validate_option() modifies 32 bits of memory but we pass
&hw->phy.autoneg_advertised which only has 16 bits and &hw->mac.fc
which only has 8 bits.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Booleans should not be compared to true or false
but be directly tested or tested with !.
Done via cocci script:
@@
bool t;
@@
- t == true
+ t
@@
bool t;
@@
- t != true
+ !t
@@
bool t;
@@
- t == false
+ !t
@@
bool t;
@@
- t != false
+ t
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the MAC is invalid or not implemented, do not abort the probe. Issue
a warning and prevent bringing the interface up until a MAC is set manually
(via ifconfig $IFACE hw ether $MAC).
Tested on two platforms, one with a valid MAC, the other without a MAC. The real
MAC is used if present, the interface fails to come up until the MAC is set on
the other. They successfully get an IP over DHCP and pass a simple ping and
login over ssh test.
This is meant to allow the Inforce SYS940X development board:
http://www.inforcecomputing.com/SYS940X_ECX.html
(and others suffering from a missing MAC) to work with the mainline kernel.
Without this patch, the probe will fail and the interface will not be created,
preventing the user from configuring the MAC manually.
This does not make any attempt to address a missing or invalid MAC for the
pch_phub driver.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Arjan van de Ven <arjan@linux.intel.com>
CC: Alan Cox <alan@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Jon Mason <jdmason@kudzu.us>
CC: netdev@vger.kernel.org
CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per discussion with Ben Hutchings and David Miller, go through and
remove assignments of "N/A" to fw_version in various drivers'
.get_drvinfo routines. While there clean-up some use of bare
constants and such.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The forcedeth changes had a conflict with the conversion over
to atomic u64 statistics in net-next.
The libertas cfg.c code had a conflict with the bss reference
counting fix by John Linville in net-next.
Conflicts:
drivers/net/ethernet/nvidia/forcedeth.c
drivers/net/wireless/libertas/cfg.c
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first #include must be pch_gbe.h as it
does a #define of pr_fmt.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform another round of floor sweeping, converting the .get_drvinfo
routines of additional drivers from strcpy to strlcpy along with
some conversion of sprintf to snprintf.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device.h header was including module.h, making it present for
most of these drivers. But we want to clean that up. Call out the
include of module.h in the modular network drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Per comments from Ben Hutchings on a previous patch, sweep the floors
a little removing unnecessary assignments of zero to fields of struct
ethtool_ringparam in driver code supporting ethtool -g.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev is unused in pch_gbe_setup_rctl. Remove this declaration to
avoid a compiler warning.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
MII Kconfig option is apart of the core networking drivers and
by default NET_CORE is enabled so drivers selecting MII will
have MII enabled as well. It was found using the randconfig
option during testing, MII would be selected but NET_CORE
could be disabled. This caused a dependency error.
Resolved the dependency by selecting NET_CORE when MII is
selected.
Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on finds for Stephen Rothwell, where current defconfig's
enable a ethernet driver and it is not compiled due to the newly
added NET_VENDOR_* component of Kconfig.
This patch enables all the "new" Kconfig options so that current
defconfig's will continue to compile the expected drivers. In
addition, by enabling all the new Kconfig options does not add
any un-expected options.
CC: Stephen Rothwll <sfc@canb.auug.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the OKI Semiconductor driver into driver/net/ethernet/oki-semi/
and make the necessary Kconfig and Makefile changes.
Note: there is no documented maintainer for this driver, so I CC'd
the last 2 major contributors.
CC: Tomoya <tomoya-linux@dsn.okisemi.com>
CC: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eric Dumazet