This allows the NIC to receive packets with bad FCS and
Runts, which can help when sniffing.
NOTE: r8169, at least on my NIC, silently drops packets
with bad FCS instead of counting them. It seems they are
only received in any fashion if the RxCRC flag is set
(which this patch allows).
Signed-off-by: Ben Greear <greearb@candelatech.com>
This allows the NIC to pass the Ethernet FCS on up
the stack, and is useful when sniffing networks.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This allows the NIC to receive Runts and frames with bad
Ethernet Frame Checksums (FCS).
Useful to sniffing & diagnosing bad networks.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This allows the NIC to pass the Ethernet Frame Checksum
(FCS) up the stack. Useful when sniffing packets.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Good for testing the RX logic for bad CRC handling.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows the NIC to receive all frames available, including
those with bad FCS, un-matched vlans, ethernet control frames,
and more.
Tested by sending frames with bad FCS.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This can aid with testing the RX logic for bad
CRCs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This enables enabling/disabling reception of the Ethernet
FCS. This can be useful when sniffing packets.
For e1000e, enabling RXFCS can change the default
behaviour for how the NIC handles CRC. Disabling RXFCS
will take the NIC back to defaults, which can be configured
as part of the module options.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The CLKDIV bitfield in the MDIO Control Register is a 16 bit field,
therefore the CLKDIV value may range from 0 to 0xffff.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
chan->chan_num is 0..CPDMA_MAX_CHANNELS-1 for tx channels and
CPDMA_MAX_CHANNELS..2*CPDMA_MAX_CHANNELS-1 for rx channels. However,
the rx and tx teardown registers expect zero based channel numbering.
Since the upper bits of the registers are reserved, the teardown also
worked before, this patch is cleanup only.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will prevent double free in some cases where be_clear() is called
for cleanup when be_setup() fails half-way.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a part of be_close(), instead of waiting for a max of 200ms for each TXQ,
wait for a total of 200ms for completions from all TXQs to arrive.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEH recovery involves ring cleanup and re-creation. The worker
thread must not run during EEH cleanup/resume.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unify return value of .ndo_set_mac_address if the given address
isn't valid. Return -EADDRNOTAVAIL as eth_mac_addr() already does
if is_valid_ether_addr() fails.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unify return value of .ndo_set_mac_address if the given address
isn't valid. Return -EADDRNOTAVAIL as eth_mac_addr() already does
if is_valid_ether_addr() fails.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unify return value of .ndo_set_mac_address if the given address
isn't valid. Return -EADDRNOTAVAIL as eth_mac_addr() already does
if is_valid_ether_addr() fails.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch seeks to clean up the timer related code. It begins by
moving one-time timer setup code from tg3_open() to tg3_init_one().
It then creates a function that encapsulates the code needed to start
the timer. A tg3_timer_stop() function was added for parity. Finally,
this patch moves all the timer functions to a more suitable location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error happens in the tx completion thread, tg3_reset_task will be
scheduled and TX_RECOVERY_PENDING will be set. The TX_RECOVERY_PENDING
flag causes tg3_poll[_msix] to return early before doing much of its
work. Tg3_reset_task() gets canceled when the configuration of the
device is changing, which always results in a chip reset. When this
happens, the TX_RECOVERY_PENDING flag may be left set, which would
unnecessarily hinder tg3_poll from doing work. This patch fixes the
problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_phy_copper_begin() has code that configures the link
advertisements through the use of the link_config.speed and
link_config.duplex members. The driver does not internally use these
members in this way, nor is it (currently) permitted via the ethtool
interface. This patch removes the dead code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver tried to detect link changes by comparing the tg3 local
active_speed member with SPEED_UNKNOWN (or formerly SPEED_INVALID).
This check is not correct, since phylib will never set its speed member
to either of these two values. The code only appeared to work because
tg3 initializes active_speed to SPEED_INVALID during tg3_init_one. This
patch introduces a new "old_link" tg3 member and then compares the
phy_device's link member against it to detect link state changes.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_for_each_possible_channel_tx_queue() should do nothing for RX-only
or extra channels. The current definition results in allocating
additional unused hardware TX queues when using the mqprio qdisc and
either separate_tx_channels or SR-IOV.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We have a very simple way of allocating buffer table entries to
queues, which is just to take the next one available. The extra
channels are the highest numbered channels but they need to be
allocated the lowest entries so that the traffic channels can be
allocated new entries without any collisions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_vfdi_set_status_page() validates the peer page count by
calculating the size of a request containing that many addresses and
comparing that with the maximum valid request size (4KB). The
calculation involves a multiplication that may overflow on a 32-bit
system.
We use kcalloc() to allocate memory to store the addresses; that also
does a multiplication and it does check for integer overflow, so any
values larger than 0x1fffffff will be rejected. However, values in
the range [0x1fffffffc, 0x1fffffff] pass boh tests and result in an
attempt to allocate nearly 4GB on the heap. This should be rejected
rather quickly as it's obviously impossible on a 32-bit system, and
indeed the maximum possible heap allocation is 32MB. Still, let's
make absolutely sure by fixing the initial validation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This requirement was meant to be implied in the name 'status page'.
One out-of-tree VF driver allocates a buffer using the structure size
and not a full page - hence the current odd specification - but in
practice that allocation will be padded and aligned to at least 4KB.
Therefore, we can specify this and have the option to extend the
structure up to 4KB without worrying about VF drivers using odd-shaped
buffers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Use eth_mac_addr() for .ndo_set_mac_address, remove
typhoon_set_mac_address() since it do currently the same as
eth_mac_addr(). Additional advantage: eth_mac_addr() already
checks if the given address is valid.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Acked-by: Dave Dillow <dave@thedillows.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is the last user of the IRQF_SAMPLE_RANDOM flag for net drivers, and since add_*_randomness
interfaces have now deprecated the flag as a source of external noise, we can remove it.
Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
isdn source code uses a not-current coding style.
Update the coding style used on a per-line basis
so that git diff -w shows only elided blank lines
at EOF.
Done with emacs and some scripts and some typing.
Built x86 allyesconfig.
No detected change in objdump -d or size.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch provides workaround for BUG in FW 7.2.16,
which in GRO mode may miscalculate buffer and
place on SGE one frag less than it could.
It may happen only for some MTUs, we mark these MTUs
with gro_check flag during device initialization or
MTU change.
Next FW should include fix for the issue and the
patch could be reverted.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with Tx only section for single cached SGEs.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch integrates FW 7.2.16 HSI and implements driver
part of GRO flow.
FW 7.2.16 adds the ability to aggregate packets for GRO
(and not just LRO) and also fixes some bugs.
1. Added new aggregation mode: GRO. In this mode packets are aggregated
such that the original packets can be reconstructed by the OS.
2. 57712 HW bug workaround - initialized all CAM TM registers to 0x32.
3. Adding the FCoE statistics structures to the BNX2X HSI.
4. Wrong configuration of TX HW input buffer size may cause theoretical
performance effect. Performed configuration fix.
5. FCOE - Arrival of packets beyond task IO size can lead to crash.
Fix firmware data-in flow.
6. iSCSI - In rare cases of on-chip termination the graceful termination
timer hangs, and the termination doesn't complete. Firmware fix to MSL
timer tolerance.
7. iSCSI - Chip hangs when target sends FIN out-of-order or with isles
open at the initiator side. Firmware implementation corrected to drop
FIN received out-of-order or with isles still open.
8. iSCSI - Chip hangs when in case of retransmission not aligned to 4-bytes
from the beginning of iSCSI PDU. Firmware implementation corrected
to support arbitrary aligned retransmissions.
9. iSCSI - Arrival of target-initiated NOP-IN during intense ISCSI traffic
might lead to crash. Firmware fix to relevant flow.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes enic_probe to do a fw init devcmd for sriov vfs.
This enables vf driver in the guest to get into adapter init state without
having to explicitly issue an init fw cmd with portprofile info. But a
successful init on the vf will require the port profile information to be
pre-provisioned by the hypervisor via the pf
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the ndo_set_vf_mac netdev op to set the sriov vf mac
in adapter using the new fw devcmd CMD_SET_MAC_ADDR. During port profile
associate the pf driver gets the vf mac using CMD_GET_MAC_ADDR.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new devcmd CMD_SET_MAC_ADDR to set the mac address of an
interface.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
firmware devcmd CMD_MAC_ADDR gets the mac address of a vnic from adapter.
This patch renames it to CMD_GET_MAC_ADDR more appropriately.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt adi ethernet driver to changes in bfin_get_ether_addr()
from arch/blackfin. bfin_get_ether_addr() returns now a state.
Set a random mac address via new eth_hw_addr_random() in case
the return value is not 0.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: change the logic to reduce unneeded checks
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct spelling "platfom" to "platform" in
drivers/net/ethernet/lantiq_etop.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8304859a "bnx2x: add fan failure event handling" made the function
bnx2x_close() non-static unnecessarily. The function is not called from
other sources. Make it static again.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c
Small minor conflict in bnx2x, wherein one commit changed how
statistics were stored in software, and another commit
fixed endianness bugs wrt. reading the values provided by
the chip in memory.
Signed-off-by: David S. Miller <davem@davemloft.net>
The majority of them are regression fixes for stuff that broke during
the merge 3.3 window.
The notable ones are:
* The at91 ata drivers both broke because of an earlier cleanup patch that
some other patches were based on. Jean-Christophe decided to remove
the legacy at91_ide driver and fix the new-style at91-pata driver while
keeping the cleanup patch. I almost rejected the patches for being too
late and too big but in the end decided to accept them because they
fix a regression.
* A patch fixing build breakage from the sysdev-to-device conversion
colliding with other changes touches a number of mach-s3c files.
* b0654037 "ARM: orion: Fix Orion5x GPIO regression from MPP cleanup"
is a mechanical change that unfortunately touches a lot of lines
that should up in the diffstat.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIVAwUATztTM2CrR//JCVInAQJu3Q/+KN4npDjjJbRm1FR4J+z7dEy3631gt7Ku
M64JuC2259da0AtXlHXoc8XB7ZrBkMR2k1n+Q42FqUFVILOXcrHSTId6osPQ8WYE
TGWR0E2APP6/w4YH3dz0aTUauX0HhnWNP4ShWalWxw2Zsc1nhPNcMO3k57E/PNnp
nUHb2ZR+Huqk9Eje6/Vkr7OQq7dhl0KJvITJKCT1H93vVYZc5l2O5ZytcOC3dsFg
yMP/btmu9JlCenOwoKcQFv6ug0tWAYiY4ALqQujLN0kcf7rmjLLOG2HQrnycmeh3
gv9jwK04gYxHkhPbCLCgO/bg906LVcYIl9/TY7jXK8oE4kR0vVxdQOWEzKIX5+KO
dyAuwy3uGi4szG8f1DKnz1h7vR1MEyBVgQ+yRqnfhLh7mFmuZcOlGTzziD3csDXG
qd5B2xf9WvLupfpbvgnHUUKEIJVfWPDoJeN3jGCOjd4+j8OzPR6yeAtU85TDQzIx
IKs2x+0zrYMBre3R+m5vb9v3IhPb1wZU29eXXRzDmLuHJDM00Qc8LmpiWUoeu3cX
DwuLstYLm8EhWN+LnjAABd3mKeR5tyBojK3EsDFRxIfz3mKHVNEAPE6Iky60Lfwr
Pq+LgBBftFfcct70UyXWSK7UI92suavDgCHVejIxpbvIWF1UVY7S1mgmflZ1WZAL
R5tdx6oe5Y4=
=QYVn
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
These are the bug fixes that have accumulated since 3.3-rc3 in arm-soc.
The majority of them are regression fixes for stuff that broke during
the merge 3.3 window.
The notable ones are:
* The at91 ata drivers both broke because of an earlier cleanup patch that
some other patches were based on. Jean-Christophe decided to remove
the legacy at91_ide driver and fix the new-style at91-pata driver while
keeping the cleanup patch. I almost rejected the patches for being too
late and too big but in the end decided to accept them because they
fix a regression.
* A patch fixing build breakage from the sysdev-to-device conversion
colliding with other changes touches a number of mach-s3c files.
* b0654037 "ARM: orion: Fix Orion5x GPIO regression from MPP cleanup"
is a mechanical change that unfortunately touches a lot of lines
that should up in the diffstat.
* tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
ARM: at91: drop ide driver in favor of the pata one
pata/at91: use newly introduced SMC accessors
ARM: at91: add accessor to manage SMC
ARM: at91:rtc/rtc-at91sam9: ioremap register bank
ARM: at91: USB AT91 gadget registration for module
ep93xx: fix build of vision_ep93xx.c
ARM: OMAP2xxx: PM: fix OMAP2xxx-specific UART idle bug in v3.3
ARM: orion: Fix USB phy for orion5x.
ARM: orion: Fix Orion5x GPIO regression from MPP cleanup
ARM: EXYNOS: Add cpu-offset property in gic device tree node
ARM: EXYNOS: Bring exynos4-dt up to date
ARM: OMAP3: cm-t35: fix section mismatch warning
ARM: OMAP2: Fix the OMAP2 only build break seen with 2011+ ARM tool-chains
ARM: tegra: paz00: fix wrong UART port on mini-pcie plug
ARM: tegra: paz00: fix wrong SD1 power gpio
i2c: tegra: Add devexit_p() for remove
ARM: EXYNOS: Correct M-5MOLS sensor clock frequency on Universal C210 board
ARM: EXYNOS: Correct framebuffer window size on Nuri board
ARM: SAMSUNG: Fix missing api-change from subsys_interface change
ARM: EXYNOS: Fix "warning: initialization from incompatible pointer type"
...
1) VETH_INFO_PEER netlink attribute needs to have it's size validated,
from Thomas Graf.
2) 'poll' module option of bnx2x driver crashes the machine, just remove
it. From Michal Schmidt.
3) ks8851_mll driver reads the irq number from two places, but only
initializes one of them, oops. Use only one location and fix this
problem, from Jan Weitzel.
4) Fix buffer overrun and unicast sterring bugs in mellanox mlx4 driver,
from Eugenia Emantayev.
5) Swapped kcalloc() args in RxRPC and mlx4, from Axel Lin.
6) PHY MDIO device name regression fixes from Florian Fainelli.
7) If the wake event IRQ line is different from the netdevice one, we
have to properly route it to the stmmac interrupt handler. From
Francesco Virlinzi.
8) Fix rwlock lock initialization ordering bug in mac80211, from
Mohammed Shafi Shajakhan.
9) TCP lost_cnt can get out of sync, and in fact go negative, in certain
circumstances. Fix the way we specify what sequence range to operate
on in tcp_sacktag_one() to fix this bug. From Neal Cardwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
net/ethernet: ks8851_mll fix irq handling
veth: Enforce minimum size of VETH_INFO_PEER
stmmac: update the driver version to Feb 2012 (v2)
stmmac: move hw init in the probe (v2)
stmmac: request_irq when use an ext wake irq line (v2)
stmmac: do not discard frame on dribbling bit assert
ipheth: Add iPhone 4S
mlx4: add unicast steering entries to resource_tracker
mlx4: fix QP tree trashing
mlx4: fix buffer overrun
3c59x: shorten timer period for slave devices
netpoll: netpoll_poll_dev() should access dev->flags
RxRPC: Fix kcalloc parameters swapped
bnx2x: remove the 'poll' module option
tcp: fix tcp_shifted_skb() adjustment of lost_cnt_hint for FACK
ks8851: Fix NOHZ local_softirq_pending 08 warning
bnx2x: fix bnx2x_storm_stats_update() on big endian
ixp4xx-eth: fix PHY name to match MDIO bus name
octeon: fix PHY name to match MDIO bus name
fec: fix PHY name to match fixed MDIO bus name
...
method for register cache initialisation is used. Only affects a fairly
small proportion of users that both don't use explicit register defaults
and do use the cache.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pU4C
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Fixes a bootstrapping issue for some registers when a less commonly used
method for register cache initialisation is used. Only affects a fairly
small proportion of users that both don't use explicit register defaults
and do use the cache.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Fix cache defaults initialization from raw cache defaults
Ben Greear