Commit Graph

232273 Commits

Author SHA1 Message Date
Jussi Kivilinna 24d24c627c zd1211rw: add useful debug output
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:51 -05:00
Jussi Kivilinna ab419e9bda zd1211rw: enable NL80211_IFTYPE_AP
It should be safe to enable AP-mode now.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:51 -05:00
Jussi Kivilinna 1f6cccccea zd1211rw: reset rx urbs after idle period of 30 seconds
RX appears to freeze while idle. Resetting rx-urbs appears to be enough to fix
this. Do reset 30 seconds after last rx.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:51 -05:00
Jussi Kivilinna 3985a46543 zd1211rw: reset device when CR_BCN_FIFO_SEMAPHORE freezes in beacon setup
When driver fails to acquire device semaphore lock, device usually
freezes soon afterwards. So failing to acquire lock indicates us that
not everything is going right in device/fw. So reset device when
this happens.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:51 -05:00
Jussi Kivilinna a0fd751f09 zd1211rw: add TX watchdog and device resetting
When doing transfers at high speed for long time, tx queue can freeze. So add
tx watchdog. TX-watchdog checks for locked tx-urbs and reset hardware when
such is detected. Merely unlinking urb was not enough, device have to be
reseted. Hw settings are restored so that any open link will stay on after
reset.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:51 -05:00
Jussi Kivilinna 212e1a5b9d zd1211rw: collect driver settings and add function to restore theim
We need HW hard reset later in patchset to reset device after TX-stall.
Collect all settings that we have set to driver for later reset and
add restore function.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Jussi Kivilinna 8f2d8f869a zd1211rw: lower hw command timeouts
Device command timeouts are set up very high (1 sec) and this causes
AP beacon to lock up for long for example. Checking timeouts on device
it's easy to see that 1 sec timeout is not needed, when device fails
to response longer timeout doesn't help:

[  473.074419] zd1211rw 1-1:1.0: print_times() Read times:
[  473.175163] zd1211rw 1-1:1.0: print_time()     0 - 10 msec: 1506
[  473.176429] zd1211rw 1-1:1.0: print_time()    11 - 50 msec: 0
[  473.177955] zd1211rw 1-1:1.0: print_time()   51 - 100 msec: 0
[  473.180703] zd1211rw 1-1:1.0: print_time()  101 - 250 msec: 0
[  473.182101] zd1211rw 1-1:1.0: print_time()  251 - 500 msec: 0
[  473.183221] zd1211rw 1-1:1.0: print_time() 500 - 1000 msec: 20
[  473.184381] zd1211rw 1-1:1.0: print_time() 1000 - ... msec: 18

Also vendor driver doesn't use this long timeout. Therefore change
timeout to 50msec.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Jussi Kivilinna 4a3b0874a4 zd1211rw: change interrupt URB buffer to DMA buffer
As might lower beacon update CPU usage.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Jussi Kivilinna 9bca0c3b54 zd1211rw: use stack and preallocated memory for small cmd-buffers
Use stack for allocing small < 64 byte arrays in zd_chip.c and preallocated
buffer in zd_usb.c. This might lower CPU usage for beacon setup.

v2:
 - Do not use stack buffers in zd_usb.c as they would be used for urb
   transfer_buffer.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Jussi Kivilinna 5127229292 zd1211rw: batch beacon config commands together
Beacon config function writes beacon to hw one write per byte. This is very
slow (usually taking more than 100ms to finish) and causes high CPU usage
when in AP-mode (kworker at ~50% on Intel Atom N270). By batching commands
together zd_mac_config_beacon() runtime can be lowered to 1/5th and lower
CPU usage to saner levels (<10% on Atom).

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Jussi Kivilinna 9be2325636 zd1211rw: add beacon watchdog and setting HW beacon more failsafe
When doing tx/rx at high packet rate (for example simply using ping -f),
device starts to fail to respond to control messages. On non-AP modes
this only causes problems for LED updating code but when we are running
in AP-mode we are writing new beacon to HW usually every 100ms. Now if
control message fails in HW beacon setup, device lock is kept locked
and beacon data partially written. This can and usually does cause:

 1. HW beacon setup fail now on, as driver cannot acquire device lock.
 2. Beacon-done interrupt stop working as device has incomplete beacon.

Therefore make zd_mac_config_beacon() always try to release device lock
and add beacon watchdog to restart beaconing when stall is detected.

Also fix zd_mac_config_beacon() try acquiring device lock for max 500ms,
as what old code appeared to be trying to do using loop and msleep(1).

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Christian Lamparter 512119b36f mac80211: fix race between next beacon dtim and ieee80211_get_buffered_bc
On review of 'zd1211rw: implement beacon fetching and handling
ieee80211_get_buffered_bc()', Christian Lamparter noted that [1]:

   Since zd_beacon_done also uploads the next beacon so long in advance,
   there could be an equally long race between the outdated state of the
   next beacon's DTIM broadcast traffic indicator (802.11-2007 7.3.2.6)
   which -in your case- was uploaded almost a beacon interval ago and
   the xmit of ieee80211_get_buffered_bc *now*.

   The dtim bc/mc bit might be not set, when a mc/bc arrived after the
   beacon was uploaded, but before the "beacon done event" from the
   hardware. So, dozing stations don't expect the broadcast traffic
   and of course, they might miss it completely.

   It's probably better to fix this in mac80211 (see the attached hack).

[1] http://marc.info/?l=linux-wireless&m=129435041117256&w=2

CC: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna 4099e2f440 zd1211rw: implement beacon fetching and handling ieee80211_get_buffered_bc()
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna b91a515dbb zd1211rw: let zd_set_beacon_interval() set dtim_period and add AP-beacon flag
Add support for AP-mode beacon. Also disable beacon when interface is set
down as otherwise hw will keep flooding NEXT_BCN interrupts.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna f773e409b9 zd1211rw: fix ack_pending in filter_ack causing tx-packet ordering problem on monitor
For reasons not very clear yet to me, filter_ack leaves matching tx-packet
pending with 'ack_pending'. This causes tx-packet to be passed back to upper
layer after next packet has been transfered and tx-packets might end up
coming come out of monitor interface in wrong order vs. rx.

Because of this when enable AP-mode, hostapd monitor interface would get
packets in wrong order causing problems in WPA association.

So don't use mac->ack_pending when in AP-mode.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna c2fadcb3b1 zd1211rw: support setting BSSID for AP mode
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna 5cf6cf819b zd1211rw: move set_rts_cts_work to bss_info_changed
As bss_info_changed may sleep, we can as well set RTS_CTS register right away.
Keep mac->short_preamble for later use (hw reset).

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna a6fb071bbf zd1211rw: move set_multicast_hash and set_rx_filter from workers to configure_filter
Workers not needed anymore since configure_filter may sleep. Keep
mac->multicast_hash for later use (hw reset).

Signed-off-by: Jussi Kivilinna <jussi.kivilina@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna 88a1159a37 zd1211rw: fix beacon interval setup
Vendor driver uses CR_BNC_INTERVAL at various places, one is HW_EnableBeacon()
that combinies beacon interval with BSS-type flag and DTIM value in upper 16bit
of u32. The other one is HW_UpdateBcnInterval() that set_aw_pt_bi()
appears to be based on. HW_UpdateBcnInterval() takes interval argument as u16
and uses that for calculations, set_aw_pt_bi() uses u32 value that has flags
and dtim in upper part. This clearly seems wrong. Also HW_UpdateBcnInterval()
updates only lower 16bit part of CR_BNC_INTERVAL. So make set_aw_pt_bi() do
calculations on only lower u16 part of s->beacon_interval.

Also set 32bit beacon interval register before reading values from device,
as HW_EnableBeacon() on vendor driver does. This is required to make beacon
work on AP-mode, simply reading and then writing updated values is not enough
at least with zd1211b.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:48 -05:00
Jussi Kivilinna 8b17f75ced zd1211rw: add locking for mac->process_intr
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:48 -05:00
Jussi Kivilinna d741900d40 zd1211rw: cancel process_intr work on zd_chip_disable_int()
OOPS if worker is running and disconnect() is called (triggered
by unpluging device). Much harder to trigger at this stage but
later when we have AP beacon work in process_intr it happens very
easy.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:48 -05:00
Jussi Kivilinna 78fc800f06 zd1211rw: use urb anchors for tx and fix tx-queue disabling
When stress testing AP-mode I hit OOPS when unpluging or rmmodding
driver.

It appears that when tx-queue is disabled, tx-urbs might be left pending.
These can cause ehci to call non-existing tx_urb_complete() (after rmmod)
or uninitialized/reseted private structure (after disconnect()). Add skb
queue for submitted packets and unlink pending urbs on zd_usb_disable_tx().

Part of the problem seems to be usb->free_urb_list that isn't always
working as it should, causing machine freeze when trying to free the list
in zd_usb_disable_tx(). Caching free urbs isn't what other drivers seem
to be doing (usbnet for example) so strip free_usb_list.

Patch makes tx-urb handling saner with use of urb anchors.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:48 -05:00
Jouni Malinen 681d119047 mac80211: Add testing functionality for TKIP
TKIP countermeasures depend on devices being able to detect Michael
MIC failures on received frames and for stations to report errors to
the AP. In order to test that behavior, it is useful to be able to
send out TKIP frames with incorrect Michael MIC. This testing behavior
has minimal effect on the TX path, so it can be added to mac80211 for
convenient use.

The interface for using this functionality is a file in mac80211
netdev debugfs (tkip_mic_test). Writing a MAC address to the file
makes mac80211 generate a dummy data frame that will be sent out using
invalid Michael MIC value. In AP mode, the address needs to be for one
of the associated stations or ff:ff:ff:ff:ff:ff to use a broadcast
frame. In station mode, the address can be anything, e.g., the current
BSSID. It should be noted that this functionality works correctly only
when associated and using TKIP.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:45:29 -05:00
Jouni Malinen 747d753df7 mac80211: Remove obsolete TKIP flexibility
The TKIP implementation was originally prepared to be a bit more
flexible in the way Michael MIC TX/RX keys are configured. However, we
are now taking care of the TX/RX MIC key swapping in user space, so
this code will not be needed. Similarly, there were some remaining WPA
testing code that won't be used in their current form. Remove the
unneeded extra complexity.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:45:29 -05:00
Justin P. Mattock 942a84901b drivers:net:ipw2100.c change a typo comamnd to command
The below patch fixes a typo comamnd to command.

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:45:29 -05:00
Rajkumar Manoharan 391bd1c443 ath9k: reserve a beacon slot on beaconing vif addition
The beaconing vif addition is based on max beacon slot
available. So it is better to reserve a beacon slot
on interface addition and let it be configured properly
on bss_info change.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:45:29 -05:00
Johannes Berg e9d7732eaf mac80211: allow GO to scan like AP
There's no point in disallowing scanning for a
GO interface when it's not beaconing yet.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:44 -05:00
Arik Nemtsov 771bbd09f7 mac80211: pass up beacons from external BSS when operating as AP
Beacons from external BSSes are required for updating overlapping BSS
info (i.e. ERP protection). Pass them up unconditionally.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:44 -05:00
Arik Nemtsov d057e5a381 mac80211: add HW flag for disabling auto link-PS in AP mode
When operating in AP mode the wl1271 hardware filters out null-data
packets as well as management packets. This makes it impossible for
mac80211 to monitor the PS mode by using the PM bit of incoming frames.

Implement a HW flag to indicate that mac80211 should ignore the PM bit.
In addition, expose ieee80211_sta_ps_transition() to make low-level
drivers capable of controlling PS-mode.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:44 -05:00
Arik Nemtsov 8fd369eeaa mac80211: do not calc frame duration when using HW rate-control
When rate-control is performed in HW, we cannot calculate frame
duration as we do not have the skb transmission rate in SW.

ieee80211_tx_h_calculate_duration() should only be called when
ieee80211_tx_h_rate_ctrl() has been called before to initialize data
in skb->cb. This doesn't happen for drivers with HW rate-control.

Fixes the following warning when operating in AP-mode
in a driver with HW rate-control.

WARNING: at net/mac80211/tx.c:57 ieee80211_duration+0x54/0x1d8 [mac80211]()
Modules linked in: wl1271_sdio wl1271 firmware_class crc7 mac80211 cfg80211
[<c0046090>] (unwind_backtrace+0x0/0x124) from [<c0064c10>] (warn_slowpath_common+0x4c/0x64)
[<c0064c10>] (warn_slowpath_common+0x4c/0x64) from [<c0064c40>] (warn_slowpath_null+0x18/0x1c)
[<c0064c40>] (warn_slowpath_null+0x18/0x1c) from [<bf040e34>] (ieee80211_duration+0x54/0x1d8 [mac80211])
[<bf040e34>] (ieee80211_duration+0x54/0x1d8 [mac80211]) from [<bf04200c>] (invoke_tx_handlers+0xfa0/0x1088 [mac80211])
[<bf04200c>] (invoke_tx_handlers+0xfa0/0x1088 [mac80211]) from [<bf042178>] (ieee80211_tx+0x84/0x248 [mac80211])
[<bf042178>] (ieee80211_tx+0x84/0x248 [mac80211]) from [<bf042f44>] (ieee80211_tx_pending+0x12c/0x278 [mac80211])
[<bf042f44>] (ieee80211_tx_pending+0x12c/0x278 [mac80211]) from [<c0069a9c>] (tasklet_action+0x68/0xbc)
[<c0069a9c>] (tasklet_action+0x68/0xbc) from [<c006a044>] (__do_softirq+0x84/0x114)
[<c006a044>] (__do_softirq+0x84/0x114) from [<c006a1b8>] (do_softirq+0x48/0x54)
[<c006a1b8>] (do_softirq+0x48/0x54) from [<c006a4f8>] (local_bh_enable+0x98/0xcc)
[<c006a4f8>] (local_bh_enable+0x98/0xcc) from [<bf074e60>] (wl1271_rx+0x2e8/0x3a4 [wl1271])
[<bf074e60>] (wl1271_rx+0x2e8/0x3a4 [wl1271]) from [<bf071ae4>] (wl1271_irq_work+0x230/0x310 [wl1271])
[<bf071ae4>] (wl1271_irq_work+0x230/0x310 [wl1271]) from [<c0076864>] (process_one_work+0x208/0x350)
[<c0076864>] (process_one_work+0x208/0x350) from [<c0076e14>] (worker_thread+0x1cc/0x300)
[<c0076e14>] (worker_thread+0x1cc/0x300) from [<c007bb88>] (kthread+0x84/0x8c)
[<c007bb88>] (kthread+0x84/0x8c) from [<c0041494>] (kernel_thread_exit+0x0/0x8)

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:44 -05:00
Ben Greear 2cf22b897c mac80211: Recalculate channel-type on iface removal.
When a vif goes away, it could cause the super-chan
to be recalculated differently, so do that calculation
on iface removal.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:43 -05:00
Ben Greear 4e6975f7b8 ath9k: Show channel type and frequency in debugfs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:43 -05:00
Rajkumar Manoharan 4c89fe954d ath9k: do not access hw registers in FULL SLEEP
The opmode recalculation is accessing hw registers.
When it is called from remove interface callback and
if there are no vifs present then hw is moved to FULL SLEEP
by radio disable. So use power save wrappers before
accessing hw registers in calculating opmode state.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:43 -05:00
Rajkumar Manoharan b2a5c3dfec ath9k_htc: make use common of function to update txpower
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:43 -05:00
Rajkumar Manoharan 5048e8c378 ath9k: move update tx power to common
move ath_update_txpow to common to remove code duplication
in both ath9k & ath9k_htc.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:43 -05:00
Rajkumar Manoharan c344c9cb01 ath9k: use common get current channel function
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:43 -05:00
Rajkumar Manoharan 45655baa42 ath9k_htc: cancel ani work in ath9k_htc_stop
ani work is cancelled in dissaoctiation. But in some cases
during suspend, deauthention never be called. So we failed
to stop ani work which was identified by the following
warning.

Call Trace:
 [<ffffffffa0454a1d>] ieee80211_can_queue_work.clone.17+0x2d/0x40 [mac80211]
 [<ffffffffa0454a60>] ieee80211_queue_delayed_work+0x30/0x60 [mac80211]
 [<ffffffffa0567f82>] ath9k_ani_work+0x142/0x250 [ath9k_htc]
 [<ffffffff81073c70>] async_run_entry_fn+0x0/0x180
 [<ffffffffa0567e40>] ath9k_ani_work+0x0/0x250 [ath9k_htc]

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:42 -05:00
Juuso Oikarinen bf6a0579f6 cfg80211: Fix power save state after interface type change
Currently cfg80211 only configures the PSM state to the driver upon creation
of a new virtual interface, but not after interface type change. The mac80211
on the other hand reinitializes its sdata structure every time the interface
type is changed, losing the PSM configuration.

Hence, if the interface type is changed to, say, ad-hoc and then back to
managed, "iw wlan0 get power_save" will claim that PSM is enabled, when in
fact on mac80211 level it is not.

Fix this in cfg80211 by configuring the PSM state to the driver each time
the interface is brought up instead of just when the interface is created.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:42 -05:00
David Gnedt 73b30dfe4f wl1251: set rate index and preamble flag on received packets
Set the rate index rate_idx and preamble flag RX_FLAG_SHORTPRE on received
packets.

Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:42 -05:00
David Gnedt 43d136442a wl1251: enable adhoc mode
Enable adhoc support in wl1251 driver.

Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:42 -05:00
David Gnedt 8964e492b5 wl1251: implement connection quality monitoring
Implement connection quality monitoring similar to the wl1271 driver.
It triggers ieee80211_cqm_rssi_notify with the corresponding event when
RSSI drops blow RSSI threshold or rises again above the RSSI threshold.
It should be noted that wl1251 doesn't support RSSI hysteresis, instead it
uses RSSI averageing and delays events until a certain count of frames
proved RSSI change.

Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:42 -05:00
David Gnedt c3e334d294 wl1251: enable beacon early termination while in power-saving mode
Port the beacon early termination feature from wl1251 driver version
included in the Maemo Fremantle kernel.
It is enabled when going to power-saving mode and disabled when leaving
power-saving mode.

Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:42:44 -05:00
David Gnedt bb4793b3c6 wl1251: fix 4-byte TX buffer alignment
This implements TX buffer alignment for cloned or too small skb by
copying and replacing the original skb.
Recent changes in wireless-testing seems to make this really necessary.

Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:42:44 -05:00
David Gnedt e7332a4144 wl1251: fix queue stopping/waking for TX path
The queue stopping/waking functionality was broken in a way that could
cause the TX to stall if the right circumstances are met.

The problem was caused by tx_work, which is scheduled on each TX operation.
If the firmware buffer is full, tx_work does nothing. In combinition with
stopped queues or non-continues transfers, tx_work is never scheduled again.
Moreover the low watermark introduced by
9df86e2e70 never takes effect because of some
old code.

Solve this by scheduling tx_work every time tx_queue is non-empty and
firmware buffer is freed on tx_complete.

This also solves a possible but unlikely case: If less frames than the high
watermark are queued, but more than firmware buffer can hold. This results
in queues staying awake but the only scheduled tx_work doesn't transfer all
frames, so the remaining frames are stuck in the queue until more frames
get queued and tx_work is scheduled again.

Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:42:44 -05:00
Ben Greear 172710bf83 mac80211: Warn users if HT fails because of freq mismatch.
I have a netgear WNDR3700 that appears to have an off-by-four
bug in how it fills out the hti->control_chan (I configure the
AP to channel 11, it reports 15 as control_chan).

Poke a message into the kernel logs to give users a
clue as to why they are not getting the expected
channel-type or rate.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:42:44 -05:00
Ben Greear 0fa025f0a2 mac80211: Show configured channel-type in netdev debugfs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:42:43 -05:00
Ben Greear eeabee7e53 mac80211: Be more careful when changing channels.
If we cannot set the channel type, set the channel back to the
original.

Don't update the driver hardware if nothing actually changed.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:38:26 -05:00
Vasily Khoruzhick 75abde4d19 libertas: Prepare stuff for if_spi.c pm support
To support suspend/resume in if_spi we need two things:
- re-setup fw in lbs_resume(), because if_spi powercycles card;
- don't touch hwaddr on second lbs_update_hw_spec() call for same
  reason;

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:38:26 -05:00
Vasily Khoruzhick 16f775befc libertas_spi: Use workqueue in hw_host_to_card
Use workqueue to perform SPI xfers, it's necessary to fix
nasty "BUG: scheduling while atomic", because
spu_write() calls spi_sync() and spi_sync() may sleep, but
hw_host_to_card() callback can be called from atomic context.
Remove kthread completely, workqueue now does its job.
Restore intermediate buffers which were removed in commit
86c34fe89e that introduced
mentioned bug.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:38:25 -05:00
John W. Linville dbd98308a5 Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6 2011-02-03 16:35:20 -05:00