files not using feature fixup don't need asm/feature-fixups.h
files using feature fixup need asm/feature-fixups.h
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch moves ASM_CONST() and stringify_in_c() into
dedicated asm-const.h, then cleans all related inclusions.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: asm-compat.h should include asm-const.h]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On 64-bit servers, SPRN_SPRG3 and its userspace read-only mirror
SPRN_USPRG3 are used as userspace VDSO write and read registers
respectively.
SPRN_SPRG3 is lost when we enter stop4 and above, and is currently not
restored. As a result, any read from SPRN_USPRG3 returns zero on an
exit from stop4 (Power9 only) and above.
Thus in this situation, on POWER9, any call from sched_getcpu() always
returns zero, as on powerpc, we call __kernel_getcpu() which relies
upon SPRN_USPRG3 to report the CPU and NUMA node information.
Fix this by restoring SPRN_SPRG3 on wake up from a deep stop state
with the sprg_vdso value that is cached in PACA.
Fixes: e1c1cfed54 ("powerpc/powernv: Save/Restore additional SPRs for stop4 cpuidle")
Cc: stable@vger.kernel.org # v4.14+
Reported-by: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 DD1 was never a product. It is no longer supported by upstream
firmware, and it is not effectively supported in Linux due to lack of
testing.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au>
[mpe: Remove arch_make_huge_pte() entirely]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When running KVM guests on Power8 we can see a lockup where one CPU
stops responding. This often leads to a message such as:
watchdog: CPU 136 detected hard LOCKUP on other CPUs 72
Task dump for CPU 72:
qemu-system-ppc R running task 10560 20917 20908 0x00040004
And then backtraces on other CPUs, such as:
Task dump for CPU 48:
ksmd R running task 10032 1519 2 0x00000804
Call Trace:
...
--- interrupt: 901 at smp_call_function_many+0x3c8/0x460
LR = smp_call_function_many+0x37c/0x460
pmdp_invalidate+0x100/0x1b0
__split_huge_pmd+0x52c/0xdb0
try_to_unmap_one+0x764/0x8b0
rmap_walk_anon+0x15c/0x370
try_to_unmap+0xb4/0x170
split_huge_page_to_list+0x148/0xa30
try_to_merge_one_page+0xc8/0x990
try_to_merge_with_ksm_page+0x74/0xf0
ksm_scan_thread+0x10ec/0x1ac0
kthread+0x160/0x1a0
ret_from_kernel_thread+0x5c/0x78
This is caused by commit 8c1c7fb0b5 ("powerpc/64s/idle: avoid sync
for KVM state when waking from idle"), which added a check in
pnv_powersave_wakeup() to see if the kvm_hstate.hwthread_state is
already set to KVM_HWTHREAD_IN_KERNEL, and if so to skip the store and
test of kvm_hstate.hwthread_req.
The problem is that the primary does not set KVM_HWTHREAD_IN_KVM when
entering the guest, so it can then come out to cede with
KVM_HWTHREAD_IN_KERNEL set. It can then go idle in kvm_do_nap after
setting hwthread_req to 1, but because hwthread_state is still
KVM_HWTHREAD_IN_KERNEL we will skip the test of hwthread_req when we
wake up from idle and won't go to kvm_start_guest. From there the
thread will return somewhere garbage and crash.
Fix it by skipping the store of hwthread_state, but not the test of
hwthread_req, when coming out of idle. It's OK to skip the sync in
that case because hwthread_req will have been set on the same thread,
so there is no synchronisation required.
Fixes: 8c1c7fb0b5 ("powerpc/64s/idle: avoid sync for KVM state when waking from idle")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER8 restores AMOR when waking from deep sleep, but POWER9 does not,
because it does not go through the subcore restore.
Have POWER9 restore it in core restore.
Fixes: ee97b6b99f ("powerpc/mm/radix: Setup AMOR in HV mode to allow key 0")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As described in that commit:
When stop is executed with EC=ESL=0, it appears to execute like a
normal instruction (resuming from NIP when woken by interrupt). So
all the save/restore handling can be avoided completely.
This is true, except in the case of an NMI interrupt (sreset or
machine check) interrupting the instruction. In that case, the NMI
gets an "interrupt occurred while the processor was in power-saving
mode" indication. The power-save wakeup code uses that bit to decide
whether to restore some registers (e.g., LR). Because these are no
longer saved, this causes random register corruption.
It may be possible to restore this optimisation by detecting the case
of no register loss on the wakeup side, and avoid restoring in that
case, but that's not a minor fix because the wakeup code itself uses
some registers that would be live (e.g., LR).
Fixes: b9ee31e100 ("powerpc/64s/idle: POWER9 ESL=0 stop avoid save/restore overhead")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When stop is executed with EC=ESL=0, it appears to execute like a
normal instruction (resuming from NIP when woken by interrupt). So all
the save/restore handling can be avoided completely. In particular NV
GPRs do not have to be saved, and MSR does not have to be switched
back to kernel MSR.
So move the test for EC=ESL=0 sleep states out to power9_idle_stop,
and return directly to the caller after stop in that case.
This improves performance for ping-pong benchmark with the stop0_lite
idle state by 2.54% for 2 threads in the same core, and 2.57% for
different cores. Performance increase with HV_POSSIBLE defined will be
improved further by avoiding the hwsync.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 3d4fbffdd7 ("powerpc/64s/idle: POWER9 implement a separate
idle stop function for hotplug") that added power9_offline_stop() was
written before commit 7672691a08 ("powerpc/powernv: Provide a way to
force a core into SMT4 mode").
When merging the former I failed to notice that it caused us to skip
the force-SMT4 logic for offline CPUs. The result is that offlined
CPUs will not correctly participate in the force-SMT4 logic, which
presumably will result in badness (not tested).
Reconcile the two commits by making power9_offline_stop() a pre-cursor
to power9_idle_stop(), so that they share the force-SMT4 logic.
This is based on an original commit from Nick, all breakage is my own.
Fixes: 3d4fbffdd7 ("powerpc/64s/idle: POWER9 implement a separate idle stop function for hotplug")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The PSSCR value is not stored to PACA_REQ_PSSCR if the CPU does not
have the XER[SO] bug.
Fix this by storing up-front, outside the workaround code. The initial
test is not required because it is a slow path.
The workaround is made to depend on CONFIG_KVM_BOOK3S_HV_POSSIBLE, to
match pnv_power9_force_smt4_catch() where it is used. Drop the comment
on pnv_power9_force_smt4_catch() as it's no longer true.
Fixes: 7672691a08 ("powerpc/powernv: Provide a way to force a core into SMT4 mode")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When waking from a CPU idle instruction (e.g., nap or stop), the sync
for ordering the KVM secondary thread state can be avoided if there
wakeup is coming from a kernel context rather than KVM context.
This improves performance for ping-pong benchmark with the stop0 idle
state by 0.46% for 2 threads in the same core, and 1.02% for different
cores.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Implement a new function to invoke stop, power9_offline_stop, which is
like power9_idle_stop but used by the cpu hotplug code.
Move KVM secondary state manipulation code to the offline case.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 processors up to and including "Nimbus" v2.2 have hardware
bugs relating to transactional memory and thread reconfiguration.
One of these bugs has a workaround which is to get the core into
SMT4 state temporarily. This workaround is only needed when
running bare-metal.
This patch provides a function which gets the core into SMT4 mode
by preventing threads from going to a stop state, and waking up
those which are already in a stop state. Once at least 3 threads
are not in a stop state, the core will be in SMT4 and we can
continue.
To do this, we add a "dont_stop" flag to the paca to tell the
thread not to go into a stop state. If this flag is set,
power9_idle_stop() just returns immediately with a return value
of 0. The pnv_power9_force_smt4_catch() function does the following:
1. Set the dont_stop flag for each thread in the core, except
ourselves (in fact we use an atomic_inc() in case more than
one thread is calling this function concurrently).
2. See how many threads are awake, indicated by their
requested_psscr field in the paca being 0. If this is at
least 3, skip to step 5.
3. Send a doorbell interrupt to each thread that was seen as
being in a stop state in step 2.
4. Until at least 3 threads are awake, scan the threads to which
we sent a doorbell interrupt and check if they are awake now.
This relies on the following properties:
- Once dont_stop is non-zero, requested_psccr can't go from zero to
non-zero, except transiently (and without the thread doing stop).
- requested_psscr being zero guarantees that the thread isn't in
a state-losing stop state where thread reconfiguration could occur.
- Doing stop with a PSSCR value of 0 won't be a state-losing stop
and thus won't allow thread reconfiguration.
- Once threads_per_core/2 + 1 (i.e. 3) threads are awake, the core
must be in SMT4 mode, since SMT modes are powers of 2.
This does add a sync to power9_idle_stop(), which is necessary to
provide the correct ordering between setting requested_psscr and
checking dont_stop. The overhead of the sync should be unnoticeable
compared to the latency of going into and out of a stop state.
Because some objected to incurring this extra latency on systems where
the XER[SO] bug is not relevant, I have put the test in
power9_idle_stop inside a feature section. This means that
pnv_power9_force_smt4_catch() WILL NOT WORK correctly on systems
without the CPU_FTR_P9_TM_XER_SO_BUG feature bit set, and will
probably hang the system.
In order to cater for uses where the caller has an operation that
has to be done while the core is in SMT4, the core continues to be
kept in SMT4 after pnv_power9_force_smt4_catch() function returns,
until the pnv_power9_force_smt4_release() function is called.
It undoes the effect of step 1 above and allows the other threads
to go into a stop state.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Recently we added a CPU feature for Power9 DD2.0, to capture the fact
that some workarounds are required only on Power9 DD1 and DD2.0 but
not DD2.1 or later.
Then in commit 9d2f510a66 ("powerpc/64s/idle: avoid POWER9 DD1 and
DD2.0 ERAT workaround on DD2.1") and commit e3646330cf
"powerpc/64s/idle: avoid POWER9 DD1 and DD2.0 PMU workaround on
DD2.1") we changed CPU_FTR_SECTIONs to check for DD1 or DD20, eg:
BEGIN_FTR_SECTION
PPC_INVALIDATE_ERAT
END_FTR_SECTION_IFSET(CPU_FTR_POWER9_DD1 | CPU_FTR_POWER9_DD20)
Unfortunately although this reads as "if set DD1 or DD2.0", the or is
a bitwise or and actually generates a mask of both bits. The code that
does the feature patching then checks that the value of the CPU
features masked with that mask are equal to the mask.
So the end result is we're checking for DD1 and DD20 being set, which
never happens. Yes the API is terrible.
Removing the ERAT workaround on DD2.0 results in random SEGVs, the
system tends to boot, but things randomly die including sometimes
dhclient, udev etc.
To fix the problem and hopefully avoid it in future, we remove the
DD2.0 CPU feature and instead add a DD2.1 (or later) feature. This
allows us to easily express that the workarounds are required if DD2.1
is not set.
At some point we will drop the DD1 workarounds entirely and some of
this can be cleaned up.
Fixes: 9d2f510a66 ("powerpc/64s/idle: avoid POWER9 DD1 and DD2.0 ERAT workaround on DD2.1")
Fixes: e3646330cf ("powerpc/64s/idle: avoid POWER9 DD1 and DD2.0 PMU workaround on DD2.1")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
DD2.1 does not have to save MMCR0 for all state-loss idle states,
only after deep idle states (like other PMU registers).
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
DD2.1 does not have to flush the ERAT after a state-loss idle.
Performance testing was done on a DD2.1 using only the stop0 idle state
(the shallowest state which supports state loss), using context_switch
selftest configured to ping-poing between two threads on the same core
and two different cores.
Performance improvement for same core is 7.0%, different cores is 14.8%.
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commit 94a04bc25a.
In order to run HPT guests on a radix POWER9 host, we will have to run
the host in single-threaded mode, because POWER9 processors do not
currently support running some threads of a core in HPT mode while
others are in radix mode ("mixed mode").
That means that we will need the same mechanisms that are used on
POWER8 to make the secondary threads available to KVM, which were
disabled on POWER9 by commit 94a04bc25a.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The hardware can execute stop in any context, and KVM does not
require real mode because siblings do not share MMU state. This
saves a switch to real-mode when going idle.
Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are no longer any callers of IDLE_STATE_ENTER_SEQ, all callers
use IDLE_STATE_ENTER_SEQ_NORET. So drop the former.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch, write change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We don't need to use IDLE_STATE_ENTER_SEQ_NORET on Power9.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This macro is only used in idle_book3s.S, move it in there and add a
more descriptive comment.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch and write change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 CPUs have independent MMU contexts per thread, so KVM does not
need to quiesce secondary threads, so the hwthread_req/hwthread_state
protocol does not have to be used. So patch it away on POWER9, and patch
away the branch from the Linux idle wakeup to kvm_start_guest that is
never used.
Add a warning and error out of kvmppc_grab_hwthread in case it is ever
called on POWER9.
This avoids a hwsync in the idle wakeup path on POWER9.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
[mpe: Use WARN(...) instead of WARN_ON()/pr_err(...)]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There's a non-trivial dependency between some commits we want to put in
next and the KVM prefetch work around that went into fixes. So merge
fixes into next.
POWER9 DD2 PMU can stop after a state-loss idle in some conditions.
A solution is to set then clear MMCRA[60] after wake from state-loss
idle. MMCRA[60] is a non-architected bit, see the user manual for
details.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The stop4 idle state on POWER9 is a deep idle state which loses
hypervisor resources, but whose latency is low enough that it can be
exposed via cpuidle.
Until now, the deep idle states which lose hypervisor resources (eg:
winkle) were only exposed via CPU-Hotplug. Hence currently on wakeup
from such states, barring a few SPRs which need to be restored to
their older value, rest of the SPRS are reinitialized to their values
corresponding to that at boot time.
When stop4 is used in the context of cpuidle, we want these additional
SPRs to be restored to their older value, to ensure that the context
on the CPU coming back from idle is same as it was before going idle.
In this patch, we define a SPR save area in PACA (since we have used
up the volatile register space in the stack) and on POWER9, we restore
SPRN_PID, SPRN_LDBAR, SPRN_FSCR, SPRN_HFSCR, SPRN_MMCRA, SPRN_MMCR1,
SPRN_MMCR2 to the values they had before entering stop.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 DD2 can see spurious PMU interrupts after state-loss idle in
some conditions.
A solution is to save and reload MMCR0 over state-loss idle.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pnv_wakeup_noloss() expects r12 to contain SRR1 value to determine if the wakeup
reason is an HMI in CHECK_HMI_INTERRUPT.
When we wakeup with ESL=0, SRR1 will not contain the wakeup reason, so there is
no point setting r12 to SRR1.
However, we don't set r12 at all so r12 contains garbage (likely a kernel
pointer), and is still used to check HMI assuming that it contained SRR1. This
causes the OPAL msglog to be filled with the following print:
HMI: Received HMI interrupt: HMER = 0x0040000000000000
This patch clears r12 after waking up from stop with ESL=EC=0, so that we don't
accidentally enter the HMI handler in pnv_wakeup_noloss() if the value of
r12[42:45] corresponds to HMI as wakeup reason.
Prior to commit 9d29250136 ("powerpc/64s/idle: Avoid SRR usage in idle
sleep/wake paths") this bug existed, in that we would incorrectly look at SRR1
to check for a HMI when SRR1 didn't contain a wakeup reason. However the SRR1
value would just happen to never have bits 42:45 set.
Fixes: 9d29250136 ("powerpc/64s/idle: Avoid SRR usage in idle sleep/wake paths")
Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Change log and comment massaging]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On POWER9 the ERAT may be incorrect on wakeup from some stop states
that lose state. This causes random segvs and illegal instructions
when these stop states are enabled.
This patch invalidates the ERAT on wakeup on POWER9 to prevent this
from causing a problem.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Merge comment change with upstream changes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In a busy system, idle wakeups can be expected from IPIs and device
interrupts.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Idle code now always runs at the 0xc... effective address whether
in real or virtual mode. This means rfid can be ditched, along
with a lot of SRR manipulations.
In the wakeup path, carry SRR1 around in r12. Use mtmsrd to change
MSR states as required.
This also balances the return prediction for the idle call, by
doing blr rather than rfid to return to the idle caller.
On POWER9, 2-process context switch on different cores, with snooze
disabled, increases performance by 2%.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Incorporate v2 fixes from Nick]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This simplifies the asm and fixes irq-off tracing over sleep
instructions.
Also move powersave_nap check for POWER8 into C code, and move
PSSCR register value calculation for POWER9 into C.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On Power9 DD1 due to a hardware bug the Power-Saving Level Status
field (PLS) of the PSSCR for a thread waking up from a deep state can
under-report if some other thread in the core is in a shallow stop
state. The scenario in which this can manifest is as follows:
1) All the threads of the core are in deep stop.
2) One of the threads is woken up. The PLS for this thread will
correctly reflect that it is waking up from deep stop.
3) The thread that has woken up now executes a shallow stop.
4) When some other thread in the core is woken, its PLS will reflect
the shallow stop state.
Thus, the subsequent thread for which the PLS is under-reporting the
wakeup state will not restore the hypervisor resources.
Hence, on DD1 systems, use the Requested Level (RL) field as a
workaround to restore the contents of the hypervisor resources on the
wakeup from the stop state.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On wakeup from a deep stop state which is supposed to lose the
hypervisor state, we don't restore the LPCR to the old value but set
it to a "sane" value via cur_cpu_spec->cpu_restore().
The problem is that the "sane" value doesn't include UPRT and the HR
bits which are required to run correctly in Radix mode.
Fix this on POWER9 onwards by restoring the LPCR value whatever it was
before executing the stop instruction.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On POWER8, in case of
- nap: both timebase and hypervisor state is retained.
- fast-sleep: timebase is lost. But the hypervisor state is retained.
- winkle: timebase and hypervisor state is lost.
Hence, the current code for handling exit from a idle state assumes
that if the timebase value is retained, then so is the hypervisor
state. Thus, the current code doesn't restore per-core hypervisor
state in such cases.
But that is no longer the case on POWER9 where we do have stop states
in which timebase value is retained, but the hypervisor state is
lost. So we have to ensure that the per-core hypervisor state gets
restored in such cases.
Fix this by ensuring that even in the case when timebase is retained,
we explicitly check if we are waking up from a deep stop that loses
per-core hypervisor state (indicated by cr4 being eq or gt), and if
this is the case, we restore the per-core hypervisor state.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 17ed4c8f81 ("powerpc/powernv: Recover correct PACA on wakeup
from a stop on P9 DD1") promises to set the NAPSTATELOST bit in paca
after recovering the correct paca for the thread waking up from stop1
on DD1, so that the GPRs can be correctly restored on the stop exit
path. However, it loads the value 1 into r3, but stores the value in
r0 into NAPSTATELOST(r13).
Fix this by correctly set the NAPSTATELOST bit in paca after
recovering the paca on POWER9 DD1.
Fixes: 17ed4c8f81 ("powerpc/powernv: Recover correct PACA on wakeup from a stop on P9 DD1")
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Highlights include:
- Larger virtual address space on 64-bit server CPUs. By default we use a 128TB
virtual address space, but a process can request access to the full 512TB by
passing a hint to mmap().
- Support for the new Power9 "XIVE" interrupt controller.
- TLB flushing optimisations for the radix MMU on Power9.
- Support for CAPI cards on Power9, using the "Coherent Accelerator Interface
Architecture 2.0".
- The ability to configure the mmap randomisation limits at build and runtime.
- Several small fixes and cleanups to the kprobes code, as well as support for
KPROBES_ON_FTRACE.
- Major improvements to handling of system reset interrupts, correctly treating
them as NMIs, giving them a dedicated stack and using a new hypervisor call
to trigger them, all of which should aid debugging and robustness.
Many fixes and other minor enhancements.
Thanks to:
Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan,
Aneesh Kumar K.V, Anshuman Khandual, Anton Blanchard, Balbir Singh, Ben
Hutchings, Benjamin Herrenschmidt, Bhupesh Sharma, Chris Packham, Christian
Zigotzky, Christophe Leroy, Christophe Lombard, Daniel Axtens, David Gibson,
Gautham R. Shenoy, Gavin Shan, Geert Uytterhoeven, Guilherme G. Piccoli,
Hamish Martin, Hari Bathini, Kees Cook, Laurent Dufour, Madhavan Srinivasan,
Mahesh J Salgaonkar, Mahesh Salgaonkar, Masami Hiramatsu, Matt Brown, Matthew
R. Ochs, Michael Neuling, Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran,
Pan Xinhui, Paul Mackerras, Rashmica Gupta, Russell Currey, Sukadev
Bhattiprolu, Thadeu Lima de Souza Cascardo, Tobin C. Harding, Tyrel Datwyler,
Uma Krishnan, Vaibhav Jain, Vipin K Parashar, Yang Shi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vSF3
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Larger virtual address space on 64-bit server CPUs. By default we
use a 128TB virtual address space, but a process can request access
to the full 512TB by passing a hint to mmap().
- Support for the new Power9 "XIVE" interrupt controller.
- TLB flushing optimisations for the radix MMU on Power9.
- Support for CAPI cards on Power9, using the "Coherent Accelerator
Interface Architecture 2.0".
- The ability to configure the mmap randomisation limits at build and
runtime.
- Several small fixes and cleanups to the kprobes code, as well as
support for KPROBES_ON_FTRACE.
- Major improvements to handling of system reset interrupts,
correctly treating them as NMIs, giving them a dedicated stack and
using a new hypervisor call to trigger them, all of which should
aid debugging and robustness.
- Many fixes and other minor enhancements.
Thanks to: Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple,
Andrew Donnellan, Aneesh Kumar K.V, Anshuman Khandual, Anton
Blanchard, Balbir Singh, Ben Hutchings, Benjamin Herrenschmidt,
Bhupesh Sharma, Chris Packham, Christian Zigotzky, Christophe Leroy,
Christophe Lombard, Daniel Axtens, David Gibson, Gautham R. Shenoy,
Gavin Shan, Geert Uytterhoeven, Guilherme G. Piccoli, Hamish Martin,
Hari Bathini, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Mahesh J
Salgaonkar, Mahesh Salgaonkar, Masami Hiramatsu, Matt Brown, Matthew
R. Ochs, Michael Neuling, Naveen N. Rao, Nicholas Piggin, Oliver
O'Halloran, Pan Xinhui, Paul Mackerras, Rashmica Gupta, Russell
Currey, Sukadev Bhattiprolu, Thadeu Lima de Souza Cascardo, Tobin C.
Harding, Tyrel Datwyler, Uma Krishnan, Vaibhav Jain, Vipin K Parashar,
Yang Shi"
* tag 'powerpc-4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (214 commits)
powerpc/64s: Power9 has no LPCR[VRMASD] field so don't set it
powerpc/powernv: Fix TCE kill on NVLink2
powerpc/mm/radix: Drop support for CPUs without lockless tlbie
powerpc/book3s/mce: Move add_taint() later in virtual mode
powerpc/sysfs: Move #ifdef CONFIG_HOTPLUG_CPU out of the function body
powerpc/smp: Document irq enable/disable after migrating IRQs
powerpc/mpc52xx: Don't select user-visible RTAS_PROC
powerpc/powernv: Document cxl dependency on special case in pnv_eeh_reset()
powerpc/eeh: Clean up and document event handling functions
powerpc/eeh: Avoid use after free in eeh_handle_special_event()
cxl: Mask slice error interrupts after first occurrence
cxl: Route eeh events to all drivers in cxl_pci_error_detected()
cxl: Force context lock during EEH flow
powerpc/64: Allow CONFIG_RELOCATABLE if COMPILE_TEST
powerpc/xmon: Teach xmon oops about radix vectors
powerpc/mm/hash: Fix off-by-one in comment about kernel contexts ids
powerpc/pseries: Enable VFIO
powerpc/powernv: Fix iommu table size calculation hook for small tables
powerpc/powernv: Check kzalloc() return value in pnv_pci_table_alloc
powerpc: Add arch/powerpc/tools directory
...
The idle workaround does not need to load PACATOC, and it does not
need to be called within a nested function that requires LR to be
saved.
Load the PACATOC at entry to the idle wakeup. It does not matter which
PACA this comes from, so it's okay to call before the workaround. Then
apply the workaround to get the right PACA.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If not all threads were in winkle, full state loss recovery is not
necessary and can be avoided. A previous patch removed this optimisation
due to some complexity with the implementation. Re-implement it by
counting the number of threads in winkle with the per-core idle state.
Only restore full state loss if all threads were in winkle.
This has a small window of false positives right before threads execute
winkle and just after they wake up, when the winkle count does not
reflect the true number of threads in winkle. This is not a significant
problem in comparison with even the minimum winkle duration. For
correctness, a false positive is not a problem (only false negatives
would be).
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When taking the core idle state lock, grab it immediately like a regular
lock, rather than adding more tests in there. Holding the lock keeps it
stable, so there is no need to do it whole holding the reservation.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In preparation for adding more bits to the core idle state word, move
the lock bit up, and unlock by flipping the lock bit rather than masking
off all but the thread bits.
Add branch hints for atomic operations while we're here.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The ISA specifies power save wakeup due to a machine check exception can
cause a machine check interrupt (rather than the usual system reset
interrupt).
The machine check handler copes with this by doing low level machine
check recovery without restoring full state from idle, then queues up a
machine check event for logging, then directly executes the same idle
instruction it woke from. This minimises the work done before recovery
is performed.
The problem is that it requires machine specific instructions and
knowledge of the book3s idle code. Currently it only has code to handle
POWER8 idle, so POWER9 crashes when trying to execute the P8 idle
instructions which don't exist in ISAv3.0B.
cpu 0x0: Vector: e40 (Emulation Assist) at [c0000000008f3810]
pc: c000000000008380: machine_check_handle_early+0x130/0x2f0
lr: c00000000053a098: stop_loop+0x68/0xd0
sp: c0000000008f3a90
msr: 9000000000081001
current = 0xc0000000008a1080
paca = 0xc00000000ffd0000 softe: 0 irq_happened: 0x01
pid = 0, comm = swapper/0
Instead of going to sleep after recovery, do the usual idle wakeup and
state restoration by calling into the normal idle wakeup path. This
reuses the normal idle wakeup paths.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Mahesh J Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reduces the number of nops for POWER8.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The POWER8 idle code has a neat trick of programming the power on engine
to restore a low bit into HSPRG0, so idle wakeup code can test and see
if it has been programmed this way and therefore lost all state. Restore
time can be reduced if winkle has not been reached.
However this messes with our r13 PACA pointer, and requires HSPRG0 to be
written to. It also optimizes the slowest and most uncommon case at the
expense of another SPR write in the common nap state wakeup.
Remove this complexity and assume winkle sleeps always require a state
restore. This speedup could be made entirely contained within the winkle
idle code by counting per-core winkles and setting a thread bitmap when
all have gone to winkle.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No functional change.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 DD1.0 hardware has a bug where the SPRs of a thread waking up
from stop 0,1,2 with ESL=1 can endup being misplaced in the core. Thus
the HSPRG0 of a thread waking up from can contain the paca pointer of
its sibling.
This patch implements a context recovery framework within threads of a
core, by provisioning space in paca_struct for saving every sibling
threads's paca pointers. Basically, we should be able to arrive at the
right paca pointer from any of the thread's existing paca pointer.
At bootup, during powernv idle-init, we save the paca address of every
CPU in each one its siblings paca_struct in the slot corresponding to
this CPU's index in the core.
On wakeup from a stop, the thread will determine its index in the core
from the TIR register and recover its PACA pointer by indexing into
the correct slot in the provisioned space in the current PACA.
Furthermore, ensure that the NVGPRs are restored from the stack on the
way out by setting the NAPSTATELOST in paca.
[Changelog written with inputs from svaidy@linux.vnet.ibm.com]
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Call it a bug]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We concluded there may be a window where the idle wakeup code could get
to pnv_wakeup_tb_loss() (which clobbers non-volatile GPRs), but the
hardware may set SRR1[46:47] to 01b (no state loss) which would result
in the wakeup code failing to restore non-volatile GPRs.
I was not able to trigger this condition with trivial tests on real
hardware or simulator, but the ISA (at least 2.07) seems to allow for
it, and Gautham says that it can happen if there is an exception pending
when the sleep/winkle instruction is executed.
Fixes: 1706567117 ("powerpc/kvm: make hypervisor state restore a function")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 09206b600c ("powernv: Pass PSSCR value and mask to
power9_idle_stop") added additional code in power_enter_stop() to
distinguish between stop requests whose PSSCR had ESL=EC=1 from those
which did not. When ESL=EC=1, we do a forward-jump to a location
labelled by "1", which had the code to handle the ESL=EC=1 case.
Unfortunately just a couple of instructions before this label, is the
macro IDLE_STATE_ENTER_SEQ() which also has a label "1" in its
expansion.
As a result, the current code can result in directly executing stop
instruction for deep stop requests with PSSCR ESL=EC=1, without saving
the hypervisor state.
Fix this BUG by labeling the location that handles ESL=EC=1 case with
a more descriptive label ".Lhandle_esl_ec_set" (local label suggestion
a la .Lxx from Anton Blanchard).
While at it, rename the label "2" labelling the location of the code
handling entry into deep stop states with ".Lhandle_deep_stop".
For a good measure, change the label in IDLE_STATE_ENTER_SEQ() macro
to an not-so commonly used value in order to avoid similar mishaps in
the future.
Fixes: 09206b600c ("powernv: Pass PSSCR value and mask to power9_idle_stop")
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman