If a WMI command has timed out for some reason,
a late WMI response would end up updating the
response region of a new WMI request that has been
issued in the meantime.
Fix this race condition by dropping a WMI response
if a new WMI command has been issued.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no point in trying to set the LED pin
when the module is being unloaded. The target
would be reset anyway.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds macros at certain places
which could be optimized for multiple register writes.
The performance of ath9k_htc improves considerably,
especially reducing the latency involved in a scan run.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Programming the opmode in the HW can be done
before the assoc_id and STA_ID registers are
setup. This helps ath9k_htc when multiple register
writes are used.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for writing multiple registers
in a single USB command.
Specific calls from the HW code that performs multiple
register writes would be modified to make use of this
in subsequent patches.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required to implement delayed/buffered
register writes in ath9k_htc.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up beacon configuration,
removing a redundant interface type check
and updating beacon interval in the correct place.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add -D__CHECK_ENDIAN__ to driver ccflags so that sparse will
always check endianness by default.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to tests, both TSF lower and upper registers kept counting, so
the higher part could have been updated after the lower part has been
read, as shown in the following log where the upper part is read first
and the lower part next.
tsf = {00000003-fffffffd}
tsf = {00000003-00000001}
tsf = {00000004-0000000b}
This patch corrects this by checking that the upper part has not been
changed while the lower part was read. It has been tested in an IBSS
network where artifical IBSS merges have been done in order to trigger
hundreds of rollover for the TSF lower part.
It follows the logic mentionned by Derek, with only 2 register reads
needed at each additional steps instead of 3 (the minimum number of
register reads is still 3).
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The first AR9003 hardware family device supported is the
AR9300, which has the vendor:device id 168c:0030
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LDPC is enabled by the rate control if the its determined
that the target peer supports LDPC. We would have already
intersected the HT capabilities so if our peer supports
LDPC so do we.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also add a function to clean up tx status ring.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable CRC check on the descriptor fetched from host on AR9003
upon reseting the TX queue.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also reset tx status ring suring chip reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9002 hardware code enables aggregation for WEP but
mac80211 doesn't enable aggregation with WEP, and the AR9003
code family does not need this so skip it for now for AR9003
but leave the code and annotate we should eventually consider
how to remove this in consideration for the HAL unification
goals.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asynch fifo code is specific to >= AR9287 so stuff it
into the AR9002 hardware family code and skip it for AR9003
cards.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is done depending on what the EEPROM settings indicates.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We add this now as OFDM spur mitigation required accessing
the EEPROM for the AR9003 devices.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once upon a time the AR_EEPROM_MAC macro was added to let us
add a random attribute to the three 4-bytes of MAC addresses
entries we read from the EEPROM. This was good while a random
high-enough value was used which did not conflict with any
of the already existing enum eeprom_param values. With AR9003
support the enums overlap and it means we either increment
the random offset or just restore the reading logic to match
what the HAL has. I choose to do the later to synchronize
the logic on both code bases.
This should fix reading the MAC address from the EEPROM
on AR9003 hardware.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This goes with some new shiny TX IQ calibration that AR9003
hardware family supports.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the last call on calib.c which acceses PHY stuff,
with this change we calib.c is now generic between both
all supported hardware families.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is so we can share routines which access this register
on calib.c
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also move interrupt related code to mac.c
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9003 TX/RX gain is currently initialized with the other
components, so for now AR9003 does not implment this callback,
after hardware bring up we can test moving the TX/RX gain there
as well and if it works well move them to its own callback as
well.
Since all INI stuff is now moved out hw.c no longer needs to
include and touch any original INI headers/structs.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is specific to the AR9002 family only.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith