This patch (as1652) fixes a long-standing bug in ehci-hcd. The driver
relies on status polls to know when to stop port-resume signalling.
It uses the root-hub status timer to schedule these status polls. But
when the driver for the root hub is resumed, the timer is rescheduled
to go off immediately -- before the port is ready. When this happens
the timer does not get re-enabled, which prevents the port resume from
finishing until some other event occurs.
The symptom is that when a new device is plugged in, it doesn't get
recognized or enumerated until lsusb is run or something else happens.
The solution is to re-enable the root-hub status timer after every
status poll while a port resume is in progress.
This bug hasn't surfaced before now because we never used to try to
suspend the root hub in the middle of a port resume (except by
coincidence).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Norbert Preining <preining@logic.at>
Tested-by: Ming Lei <ming.lei@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1650) adds calls to the new
usb_hcd_{start,end}_port_resume() functions to ehci-hcd. Now EHCI
root hubs won't be runtime suspended while they are sending a resume
signal to one of their ports.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1624) prepares ehci-hcd for being split up into a core
library and separate platform driver modules. A generic
ehci_hc_driver structure is created, containing all the "standard"
values, and a new mechanism is added whereby a driver module can
specify a set of overrides to those values. In addition the
ehci_setup(), ehci_suspend(), and ehci_resume() routines need to be
EXPORTed for use by the drivers.
As a side effect of this change, a few routines no longer need to be
marked __maybe_unused.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1623) removes the ehci_port_power() routine and all the
places that call it. There's no reason for ehci-hcd to change the
port power settings; the hub driver takes care of all that stuff.
There is one exception: When the controller is resumed from
hibernation or following a loss of power, the ports that are supposed
to be handed over to a companion controller must be powered on first.
Otherwise the handover won't work. This process is not visible to the
hub driver, so it has to be handled in ehci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1622) removes the USB-2.1 Link Power Management code
from the ehci-hcd driver. This code was never integrated with
usbcore, it is full of bugs, and it was not getting used by anybody.
However, the debugging code for dumping the LPM-related fields in the
EHCI registers is left in place. In theory it might be useful to see
these values, even though we don't use them.
This essentially amounts to a partial revert of commit
aa4d834298 (USB: EHCI: EHCI 1.1
addendum: preparation) and an almost full revert of commit
48f2497014 (USB: EHCI: EHCI 1.1
addendum: Basic LPM feature support) plus its follow-ons.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this condition, all controllers will do this delay,
and increase the resume time.
Only enabled and unsuspended port needs this delay, but
Some buggy hardware(like Synopsys usb controller) will
clear suspend bit once they receive/send resume signal,
so it takes resume bit as consideration.
Tested it at Freescale i.mx6q Sabrelite board.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like for the in-tree early console debug port driver, the
hypervisor - when using a debug port based console - also needs to be
told about controller resets, so it can suppress using and then
re-initialize the debug port accordingly.
Other than the in-tree driver, the hypervisor driver actually cares
about doing this only for the device where the debug is port actually
in use, i.e. it needs to be told the coordinates of the device being
reset (quite obviously, leveraging the addition done for that would
likely benefit the in-tree driver too).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1589) resolves some unlikely races involving system
shutdown or controller death in ehci-hcd:
Shutdown races with both root-hub resume and controller
resume.
Controller death races with root-hub suspend.
A new bitflag is added to indicate that the controller has been shut
down (whether for system shutdown or because it died). Tests are
added in the suspend and resume pathways to avoid reactivating the
controller after any sort of shutdown.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1588) adjusts the locking in ehci-hcd's various halt,
shutdown, and suspend/resume pathways. We want to hold the spinlock
while writing device registers and accessing shared variables, but not
while polling in a loop.
In addition, there's no need to call ehci_work() at times when no URBs
can be active, i.e., in ehci_stop() and ehci_bus_suspend().
Finally, ehci_adjust_port_wakeup_flags() is called only in situations
where interrupts are enabled; therefore it can use spin_lock_irq
rather than spin_lock_irqsave.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1586) replaces the kernel timer used by ehci-hcd as an
I/O watchdog with an hrtimer event.
Unlike in the current code, the watchdog event is now always enabled
whenever any isochronous URBs are active. This will prevent bugs
caused by the periodic schedule wrapping around with no completion
interrupts; the watchdog handler is guaranteed to scan the isochronous
transfers at least once during each iteration of the schedule. The
extra overhead will be negligible: one timer interrupt every 100 ms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1583) changes ehci-hcd to use an hrtimer event for
unlinking empty (unused) async QHs instead of using a kernel timer.
The check for empty QHs is moved to a new routine, where it doesn't
require going through an entire scan of both the async and periodic
schedules. And it can unlink multiple QHs at once, unlike the current
code.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1582) changes ehci-hcd's strategy for unlinking async
QHs. Currently the driver never unlinks more than one QH at a time.
This can be inefficient and cause unnecessary delays, since a QH
cannot be reused while it is waiting to be unlinked.
The new strategy unlinks all the waiting QHs at once. In practice the
improvement won't be very big, because it's somewhat uncommon to have
two or more QHs waiting to be unlinked at any time. But it does
happen, and in any case, doing things this way makes more sense IMO.
The change requires the async unlinking code to be refactored
slightly. Now in addition to the routines for starting and ending an
unlink, there are new routines for unlinking a single QH and starting
an IAA cycle. This approach is needed because there are two separate
paths for unlinking async QHs:
When a transfer error occurs or an URB is cancelled, the QH
must be unlinked right away;
When a QH has been idle sufficiently long, it is unlinked
to avoid consuming DMA bandwidth uselessly.
In the first case we want the unlink to proceed as quickly as
possible, whereas in the second case we can afford to batch several
QHs together and unlink them all at once. Hence the division of
labor.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1581) replaces the iaa_watchdog kernel timer used by
ehci-hcd with an hrtimer event, in keeping with the general conversion
to high-res timers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1579) adds an hrtimer event to handle deallocation of
iTDs and siTDs in ehci-hcd.
Because of the frame-oriented approach used by the EHCI periodic
schedule, the hardware can continue to access the Transfer Descriptor
for isochronous (or split-isochronous) transactions for up to a
millisecond after the transaction completes. The iTD (or siTD) must
not be reused before then.
The strategy currently used involves putting completed iTDs on a list
of cached entries and every so often returning them to the endpoint's
free list. The new strategy reduces overhead by putting completed
iTDs back on the free list immediately, although they are not reused
until it is safe to do so.
When the isochronous endpoint stops (its queue becomes empty), the
iTDs on its free list get moved to a global list, from which they will
be deallocated after a minimum of 2 ms. This delay is what the new
hrtimer event is for.
Overall this may not be a tremendous improvement over the current
code, but to me it seems a lot more clear and logical. In addition,
it removes the need for each iTD to keep a reference to the
ehci_iso_stream it belongs to, since the iTD never needs to be moved
back to the stream's free list from the global list.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1577) adds hrtimer support for unlinking interrupt QHs
in ehci-hcd. The current code relies on a fixed delay of either 2 or
55 us, which is not always adequate and in any case is totally bogus.
Thanks to internal caching, the EHCI hardware may continue to access
an interrupt QH for more than a millisecond after it has been unlinked.
In fact, the EHCI spec doesn't say how long to wait before using an
unlinked interrupt QH. The patch sets the delay to 9 microframes
minimum, which ought to be adequate.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1572) begins the conversion of ehci-hcd over to using
high-resolution timers rather than old-fashioned low-resolution kernel
timers. This reduces overhead caused by timer roundoff on systems
where HZ is smaller than 1000. Also, the new timer framework
introduced here is much more logical and easily extended than the
ad-hoc approach ehci-hcd currently uses for timers.
An hrtimer structure is added to ehci_hcd, along with a bitflag array
and an array of ktime_t values, to keep track of which timing events
are pending and what their expiration times are.
Only the infrastructure for the timing operations is added in this
patch. Later patches will add routines for handling each of the
various timing events the driver needs. In some cases the new hrtimer
handlers will replace the existing handlers for ehci-hcd's kernel
timers; as this happens the old timers will be removed. In other
cases the new timing events will replace busy-wait loops.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1571) adds a new state for ehci-hcd's root hubs:
EHCI_RH_STOPPING. This value is used at times when the root hub is
being stopped and we don't know whether or not the hardware has
finished all its DMA yet.
Although the purpose may not be apparent, this distinction will come
in useful later on. Future patches will avoid actions that depend on
the root hub being operational (like turning on the async or periodic
schedules) when they see the state is EHCI_RH_STOPPING.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1569) renames the ehci->reclaim list in ehci-hcd. The
word "reclaim" is used in the EHCI specification to mean something
quite different, and "unlink_next" is more descriptive of the list's
purpose anyway.
Similarly, the "reclaim" field in the ehci_stats structure is renamed
"iaa", which is more meaningful (to experts, anyway) and is a better
match for the "lost_iaa" field.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1566) removes the code in ehci-hcd's resume routines
which tries to restart or cancel any transfers left active while the
root hub or controller was asleep. This code isn't necessary, because
all URBs are terminated before the root hub is suspended.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1563) removes a lot of duplicated code by moving the
EHCI controller suspend/resume routines into the core driver, where
the various platform drivers can invoke them as needed.
Not only does this simplify these platform drivers, this also makes it
easier for other platform drivers to add suspend/resume support in the
future.
Note: The patch does not touch the ehci-fsl.c file, because its
approach to suspend and resume is so different from all the others.
It will have to be handled specially by its maintainer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1562) cleans up the definitions of the EHCI extended
registers to be consistent with the definitions of the standard
registers. This makes the code look a lot nicer, with no functional
change.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- to decrease redundant since both ehci_hcd and ohci_hcd have the same variable
- it helps access phy in usb core code
- phy is more meaningful than transceiver
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ehci-hcd driver is a little haphazard about keeping track of the
state of the USBCMD register. The ehci->command field is supposed to
hold the register's value (apart from a few special bits) at all
times, but it isn't maintained properly.
This patch (as1543) cleans up the situation. It keeps ehci->command
up-to-date, and uses that value rather than reading the register from
the hardware whenever possible.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the conflict in:
drivers/usb/host/ehci-fsl.c
And picks up loads of xhci bugfixes to make it easier for others to test
with.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ClearPortFeature/USB_PORT_FEAT_ENABLE case, ehci_hub_control()
would read from status_reg, clear PORT_PE, and write the result back to
status_reg. This would clear any bits in PORT_RWC_BITS that were set in
the registers. Fix this by masking these bits off before the write.
Since this masking is common across all ClearPortFeature cases, move it
into a single early location to avoid duplicating it.
Remove the same bugfix from ehci-tegra.c's tegra_ehci_hub_control(), now
that this case is correctly handled by the core.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It displays wrong debug message if we plug in a full/low
speed device at port for builtin TT controller. We can get
device/port speed information at following code of hub_port_init,
so it is better to replace it with debug message of "reset complete".
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1537) adds a bit-array to ehci-hcd for keeping track of
which ports are undergoing a resume transition. If any of the bits
are set when ehci_hub_status_data() is called, the routine will return
a nonzero value even if no ports have any status changes pending.
This will allow usbcore to handle races between root-hub suspend and
port wakeup.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Chen Peter-B29397 <B29397@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
splits OTG functionality away from transceivers.
We have known for quite a long time that struct otg_transceiver was
a bad name for the structure, considering transceiver is far from
being OTG-specific (see 4e67185).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WiB6
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB: transceiver changes for 3.4
Here we have a big rework done by Heikki Krogerus (thanks) which
splits OTG functionality away from transceivers.
We have known for quite a long time that struct otg_transceiver was
a bad name for the structure, considering transceiver is far from
being OTG-specific (see 4e67185).
This changes the otg functions so that they receive struct
otg instead of struct usb_phy as parameter and
converts all users of these functions to pass the otg member
of their usb_phy.
Includes fixes to IMX code from Sascha Hauer.
[ balbi@ti.com : fixed a compile warning on ehci-mv.c ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
not all platforms will use all of those ehci_*
symbols on their hc_driver structure. Sometimes
we might need to provide a modified version of
a certain method or not provide it at all, as is
the case with OMAPs which don't support port handoff
feature.
Whenever we compile a kernel for an OMAP board with
EHCI enabled, we get compile warnings:
drivers/usb/host/ehci-hub.c:1079: warning: 'ehci_relinquish_port' \
defined but not used
drivers/usb/host/ehci-hub.c:1088: warning: 'ehci_port_handed_over' \
defined but not used
In order to cleanup those warnings, we're adding
__maybe_unused annotation to those functions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1483) improves the ehci-hcd driver family by getting rid
of the reliance on the hcd->state variable. It has no clear owner and
it isn't protected by the usual HCD locks. In its place, the patch
adds a new, private ehci->rh_state field to record the state of the
root hub.
Along the way, the patch removes a couple of lines containing
redundant assignments to the state variable. Also, the QUIESCING
state simply gets changed to the RUNNING state, because the driver
doesn't make any distinction between them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From EHCI Spec p.28 HC should clear PORT_SUSPEND when SW clears
PORT_RESUME. In Intel Oaktrail platform, MPH (Multi-Port Host
Controller) core clears PORT_SUSPEND directly when SW sets PORT_RESUME
bit. If we rely on PORT_SUSPEND bit to stop USB resume, we will miss
the action of clearing PORT_RESUME. This will cause unexpected long
resume signal on USB bus.
Signed-off-by: Wang Zhi <zhi.wang@windriver.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The sequence to put port in test mode is not complete.
According EHCI specification all enabled ports must be
put in suspend.
Signed-off-by: Boris Todorov <boris.st.todorov@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MAX4967 USB power supply chip we use on our boards signals over-current when
power is not enabled; once it's enabled, over-current signal returns to normal.
That unfortunately caused the endless stream of "over-current change on port"
messages. The EHCI root hub code reacts on every over-current signal change
with powering off the port -- such change event is generated the moment the
port power is enabled, so once enabled the power is immediately cut off.
I think we should only cut off power when we're seeing the active over-current
signal, so I'm adding such check to that code. I also think that the fact that
we've cut off the port power should be reflected in the result of GetPortStatus
request immediately, hence I'm adding a PORTSCn register readback after write...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only sysfs attr implemented so far is "companion" from ehci-hub.c,
but in the next patch we are going to add another sysfs file, so prior
to that let's structure things and move already-in-there sysfs code to
separate file.
NOTE: All the code I'm moving into this new file was written by Alan
Stern (in 57e06c11 "EHCI: force high-speed devices to run at full
speed"; Jan 16 2007), that's why I'm putting
Copyright (C) 2007 by Alan Stern
there after explicit request from the author.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark ehci_adjust_port_wakeup_flags as __maybe_unused to avoid the following
warning when building the ehci-mxc driver:
CC drivers/usb/host/ehci-hcd.o
drivers/usb/host/ehci-hub.c:130: warning: 'ehci_adjust_port_wakeup_flags' defined but not used
Current ehci-mxc driver implementation does not support suspend/resume.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the USB core to deal with USB 3.0 hubs. These hubs have a slightly
different hub descriptor than USB 2.0 hubs, with a fixed (rather than
variable length) size. Change the USB core's hub descriptor to have a
union for the last fields that differ. Change the host controller drivers
that access those last fields (DeviceRemovable and PortPowerCtrlMask) to
use the union.
Translate the new version of the hub port status field into the old
version that khubd understands. (Note: we need to fix it to translate the
roothub's port status once we stop converting it to USB 2.0 hub status
internally.)
Add new code to handle link state change status. Send out new control
messages that are needed for USB 3.0 hubs, like Set Hub Depth.
This patch is a modified version of the original patch submitted by John
Youn. It's updated to reflect the removal of the "bitmap" #define, and
change the hub descriptor accesses of a couple new host controller
drivers.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Max Vozeler <mvz@vozeler.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Using a #define to redefine a common variable name is a bad thing,
especially when the #define is in a header. include/linux/usb/hcd.h
redefined bitmap to DeviceRemovable to avoid typing a long field in the
hub descriptor. This has unintended side effects for files like
drivers/usb/core/devio.c that include that file, since another header
included after hcd.h has different variables named bitmap.
Remove the bitmap #define and replace instances of it in the host
controller code. Cleanup the spaces around function calls and square
brackets while we're at it.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Max Vozeler <mvz@vozeler.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
If a device plug/unplug is detected on an ATI SB700 USB controller in D3,
it appears to set the port status register but not the controller status
register. As a result we'll fail to detect the plug event. Check the port
status register on resume as well in order to catch this case.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable <stable@kernel.org> [after .39-rc1 is out]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed to resolve some merge conflicts that were found
in the USB host controller patches, and reported by Stephen Rothwell.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In create_companion_file() there is a bogus assignemt to i created for
the express purpose of avoiding an ignored return value warning.
With pre-release GCC-4.6, this causes a 'set but not used' warning.
Kick the problem further down the road by just returning i. All the
callers of create_companion_file() ignore its return value, so all is
good:
o No warnings are issued.
o We still subvert the desires of the authors of device_create_file()
by ignorning error conditions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1394) adds code to ehci-hcd, ohci-hcd, and uhci-hcd for
automatically resuming the root hub when the controller is resumed, if
the root hub has a wakeup request pending on some port.
During resume from system sleep this doesn't matter, because the root
hubs will naturally be resumed along with every other device in the
system. However it _will_ matter for runtime PM: If the controller is
suspended and a remote wakeup request is received then the controller
will autoresume, but we need to ensure that the root hub also
autoresumes. Otherwise the wakeup request would be ignored, the
controller would go back to sleep, and the cycle would repeat a large
number of times (I saw this happen before the patch was written).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1385) adds a "do_wakeup" parameter to the pci_suspend
method used by PCI-based host controller drivers. ehci-hcd in
particular needs to know whether or not to enable wakeup when
suspending a controller. Although that information is currently
available through device_may_wakeup(), when support is added for
runtime suspend this will no longer be true.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1393) converts several of the single-bit fields in
struct usb_hcd to atomic flags. This is for safety's sake; not all
CPUs can update bitfield values atomically, and these flags are used
in multiple contexts.
The flag fields that are set only during registration or removal can
remain as they are, since non-atomic accesses at those times will not
cause any problems.
(Strictly speaking, the authorized_default flag should become atomic
as well. I didn't bother with it because it gets changed only via
sysfs. It can be done later, if anyone wants.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch will enable Per-port event feature defined in EHCI 1.1
addendum. This feature addresses an issue where HCD is currently
required to read and parse PORTSC for all enabled root hub ports. With
this patch, the overhead will be reduced.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With this patch, the LPM capable EHCI host controller can put device
into L1 sleep state which is a mode that can enter/exit quickly, and
reduce power consumption.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1380) fixes a bug in the wakeup settings for EHCI host
controllers. When the controller is suspended, if it isn't enabled
for remote wakeup then we have to turn off all the port wakeup flags.
Disabling PCI PME# isn't good enough, because some systems (Intel)
evidently use alternate wakeup signalling paths.
In addition, the patch improves the handling of the Intel Moorestown
hardware by performing various power-up and power-down delays just
once instead of once for each port (i.e., the delays are moved outside
of the port loops). This requires extra code, but the total delay
time is reduced.
There are also a few additional minor cleanups.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Ondrej Zary <linux@rainbow-software.org>
CC: Alek Du <alek.du@intel.com>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern