Add a check after the for loops to see if we found what we were looking
for or if we reached the end of the list.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
CONFIG_FONTS has nothing to do with whether find_font() is defined.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Add support for newer firmware version that uses different
buffer format. Makes hardware work for many users.
* Register name updates
* Lot of refactoring
* Lots of fixes as a result of full testing
* Idle mode is done now by resetting the device, and this eliminates
the ugly sample_period = 75 hack.
Every feature of the driver is now well tested.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Be sure to rollback all init if input register fails.
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As soon as input device is registered, it might be accessed (and it is)
This can trigger a hardware interrupt that can access
not yet initialized ir->raw, (by sending a sample)
This can be reproduced by holding down a remote button and reloading the module.
And this always crashes the systems where hardware decides to send an interrupt
right at the moment it is enabled.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Unfortunelly (my fault) the kernel thread that now handles IR processing
has classical races in regard to wakeup and stop.
This patch hopefully closes them all.
Tested with module reload running in a loop, while receiver is blasted
with IR data for 10 minutes.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The rc map table were corrected thanks to Giorgio input and tests.
Reported-by: Giorgio Vazzana <mywing81@gmail.com>
Tested-by: Giorgio Vazzana <mywing81@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for tuning with PSK8 modulation, pilot and rolloff
with the S2 versions of firedtv.
Signed-off-by: Tommy Jonsson <quazzie2@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (trivial simplification)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is possible that, while ir_unregister_class() is handling, some
application could try to access the sysfs nodes, causing an OOPS.
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is an integer overflow here because 0x03000000 * 1000 is too large
for 31 bits.
rawir.duration should be in terms of nsecs.
IR_MAX_DURATION and 0x03000000 are already in terms of nsecs.
STREAMZAP_TIMEOUT and STREAMZAP_RESOLUTION are 255 and 256 respectively
and are in terms of usecs.
The original code had a deadline of 1.005 seconds and the new code has a
deadline of .065 seconds.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As pointed out (and tested) by Joris van Rantwijk, we do actually need
to wire up .compat_ioctl for 32-bit lirc userspace to work with 64-bit
lirc kernelspace. Do it. And add a check to make sure we get a valid
irctl in the ioctl handler.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
>From Joris van Rantwijk <jorispubl@xs4all.nl>:
I tested lirc_serial and found that it works fine.
Except the LIRC ioctls do not work in my 64-bit-kernel/32-bit-user
setup. I added compat_ioctl entries in the drivers to fix this.
While doing so, I noticed inconsistencies in the argument type of
the LIRC ioctls. All ioctls are declared in lirc.h as having argument
type __u32, however there are a few places where the driver calls
get_user/put_user with an unsigned long argument.
The patch below changes lirc_dev and lirc_serial to use __u32 for all
ioctl arguments, and adds compat_ioctl entries.
It should probably also be done in the other low-level drivers,
but I don't have hardware to test those.
I've dropped the .compat_ioctl addition from Joris' original patch,
as I swear the non-compat definition should now work for both 32-bit
and 64-bit userspace. Technically, I think we still need/want a
in getting a reply to you).
Reported-by: Joris van Rantwijk <jorispubl@xs4all.nl>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Per discussion with Andy Walls on irc, rx fifo overruns are not all that
uncommon on a busy system, and the initial posting of the nuvoton-cir
driver doesn't handle them well enough. With this addition, we'll drain
the hw fifo, attempt to process any ir pulse trains completed with that
flush, then we'll issue a hw rx fifo clear and reset the raw ir sample
kfifo and start over collecting raw ir data.
Also slightly refactors the cir interrupt enabling so that we always get
consistent flags set and only have to modify them in one place, should
they need to be altered.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a new ir-core pnp driver for the Nuvoton w836x7hg integrated CIR
function. The chip is found on at least the ASRock ION 330HT boxes and
apparently, on a number of Intel DP55-series motherboards:
http://www.asrock.com/nettop/overview.asp?Model=ION%20330HThttp://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=17685&lang=eng
This driver was made possible by a hardware donation from Nuvoton, along
with sample code (in the form of an lirc driver) and datasheet, so huge
thanks to them for supporting this effort. Note that this driver
constitutes a massive rewrite, porting from the lirc interfaces to the
ir-core interfaces, and restructuring the driver to look more like Maxim
Levitsky's ene_ir driver (as well as generally making it look more like
kernel code).
There's some work left to be done on this driver, to fully support the
range of functionality possible, but receive and IR power-on/wake are
both functional (may require setting wake key under another OS atm). The
hardware I've got (one of the ASRock boxes) only supports RX, so TX is
completely untested as of yet. Certain RX parameters, like sample
resolution and RX IRQ sample length trigger level could possibly stand
to be made tweakable via modparams or sysfs nodes, but the current
values work well enough for me w/an MCE RC6A remote.
The original lirc driver carried support for the Windows MCE IR
keyboard/mouse device, which I plan to add back generically, in a way
that should be usable by any raw IR receiver (or at least by this driver
and the mceusb driver).
Suspend and resume have also been tested, the power button on my remote
can be used to wake the machine, and CIR functionality resumes just
fine. Module unload/reload has also been tested, though not extensively
or repetitively. Also tested to work with the lirc bridge plugin for
userspace decoding.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new control mechanism uses dynamic control values in the subdriver
descriptor. It simplifies standard control handling.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Take the ctrl_mutex mutex before touching control information in those
functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
XU control information is supposed to be entirely discoverable using
standard UVC queries. As some devices report bogus information (such as
reporting a read-only control as being read-write), add a fixup table
for XU controls.
This table can also be used to selectively disable requests supposed to
be supported by all XU controls (GET_MIN, GET_MAX, GET_DEF, GET_RES) but
not correctly (or at all) supported by the device.
The table currently disables GET_CUR on the Logitech motor control XU
pan/tilt controls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
XU controls initialization requires querying the device for control
information. As some buggy UVC devices will crash when queried
repeatedly in a tight loop, delay XU controls initialization until first
use.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that control information structures are not shared between control
instances, embed a uvc_control_info instance inside the uvc_control
structure instead of storing a pointer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the sysadmin requirements for UVCIOC_CTRL_MAP (and the stub
implementation of UVCIOC_CTRL_ADD). This requirement no longer makes sense with
the new XU control access mechanisms since XU controls can be accessed without
adding control mappings first.
A maximum number (currently 1024) of control mappings per device is enforced to
avoid excess memory consumption caused by careless user space applications.
Signed-off-by: Martin Rubli <martin_rubli@logitech.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devices advertise XU controls using a bitmask, in which each bit
corresponds to a control. The control selector, used to query the
control, isn't available in the USB descriptors.
All known UVC devices use control selectors equal to the control bit
index plus one. Hardcode that relationship in the driver, making the
UVCIOC_CTRL_ADD ioctl obsolete. All necessary information about XU
controls can be obtained by the driver at enumeration time.
The UVCIOC_CTRL_ADD ioctl is still supported for compatibility reasons,
but now always returns -EEXIST.
Finally, control mappings are now on a per-device basis and no longer
global.
As this changes the userspace interface, bump the driver version number
to 1.0.0 (it was about time).
Signed-off-by: Martin Rubli <martin_rubli@logitech.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Increase the sequence number of the v4l2_buffer structure regardless of
any buffer states, so that discontinuous sequence numbers allow
applications to detect lost video frames.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bandwidth estimate computed with the FIX_BANDIWDTH quirk is too low
for many cameras. Don't use maximum packet sizes lower than 1024 bytes
to try and work around the problem. According to measurements done on
two different camera models, the value is high enough to get most
resolutions working while not preventing two simultaneous VGA streams at
15 fps.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of printing the query hex value in error messages, print its
name to make the messages more readable.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
They're not modified by the function, make them const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Hercules Dualpix Exchange (06f8:3005) camera expose an absolute zoom
that is not implemented. Blacklist it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't hold the lock before unregistering the device, since when the
device is unregistered the datastruct containing the lock may be freed
(if the refcount went to 0).
Also fixed the framework documentation that erroneously suggested the
wrong locking order as well.
Reported-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use new RC core instead of old legacy RC implementation.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Imported from af9015.h. Initial keytable was from
Jose Alberto Reguero <jareguero@telefonica.net> and
Felipe Morales Moreno <felipe.morales.moreno@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Digittrade DVB-T USB Stick remote controller.
Imported from af9015.h. Initial keytable was from Alain Kalker <miki@dds.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Imported from af9015.h.
Initial keytable was from Marc Schneider <macke@macke.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
MSI DIGIVOX mini III remote controller. Uses NEC extended 0x61d6.
This remote seems to be same as rc-kworld-315u.c. Anyhow, add new remote
since rc-kworld-315u.c lacks NEC extended address byte.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Variable is don't care in that case. No need to set value.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The AVerTV Red HD+ (A850T) is basically the same as the existing
AVerTV Volar Black HD (A850), but is specific to the french market.
The A850T identifies itself as a A850, but has its own PID. It even
suffers from the same EEPROM deficiencies.
This is based off a collection of information gathered from the
french support forums for Ubuntu, which I tried to properly format
into this patch:
http://forum.ubuntu-fr.org/viewtopic.php?pid=3322825
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@anciens.enib.fr>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Demod + tuner specific RF AGC and IF AGC limit values are read from demod
memory in every signal strength query. Cache those to reduce I2C traffic.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Precalculate coefficients register values. This reduces text size around 300 bytes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of doing its own lock, use core-assisted one. As a bonus, it
will do the proper unlock during queue wait events. This fixes a
long-standing bug where softwares like tvtime would hang if you try to
use cx231xx-alsa.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This file came originally from cx23885 driver. Some functions aren't
used. Now that they are declared as static, we have those errors:
drivers/media/video/cx231xx/cx231xx-417.c:615: warning: ‘mc417_gpio_set’ defined but not used
drivers/media/video/cx231xx/cx231xx-417.c:625: warning: ‘mc417_gpio_clear’ defined but not used
drivers/media/video/cx231xx/cx231xx-417.c:635: warning: ‘mc417_gpio_enable’ defined but not used
As they're not used, just remove them. If needed, they can be restored from
the git logs or from the cx23885 driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/cx23885/built-in.o: In function `mc417_memory_write':
/home/v4l/v4l/patchwork/drivers/media/video/cx23885/cx23885-417.c:482: multiple definition of `mc417_memory_write'
drivers/media/video/cx231xx/built-in.o:/home/v4l/v4l/patchwork/drivers/media/video/cx231xx/cx231xx-417.c:477: first defined here
drivers/media/video/cx23885/built-in.o: In function `mc417_gpio_set':
/home/v4l/v4l/patchwork/drivers/media/video/cx23885/cx23885-417.c:636: multiple definition of `mc417_gpio_set'
drivers/media/video/cx231xx/built-in.o:/home/v4l/v4l/patchwork/drivers/media/video/cx231xx/cx231xx-417.c:615: first defined here
drivers/media/video/cx23885/built-in.o: In function `mc417_gpio_enable':
/home/v4l/v4l/patchwork/drivers/media/video/cx23885/cx23885-417.c:656: multiple definition of `mc417_gpio_enable'
drivers/media/video/cx231xx/built-in.o:/home/v4l/v4l/patchwork/drivers/media/video/cx231xx/cx231xx-417.c:635: first defined here
drivers/media/video/cx23885/built-in.o: In function `mc417_memory_read':
/home/v4l/v4l/patchwork/drivers/media/video/cx23885/cx23885-417.c:546: multiple definition of `mc417_memory_read'
drivers/media/video/cx231xx/built-in.o:/home/v4l/v4l/patchwork/drivers/media/video/cx231xx/cx231xx-417.c:541: first defined here
drivers/media/video/cx23885/built-in.o: In function `mc417_gpio_clear':
/home/v4l/v4l/patchwork/drivers/media/video/cx23885/cx23885-417.c:646: multiple definition of `mc417_gpio_clear'
drivers/media/video/cx231xx/built-in.o:/home/v4l/v4l/patchwork/drivers/media/video/cx231xx/cx231xx-417.c:625: first defined here
drivers/media/video/cx23885/built-in.o: In function `mc417_register_read':
/home/v4l/v4l/patchwork/drivers/media/video/cx23885/cx23885-417.c:388: multiple definition of `mc417_register_read'
drivers/media/video/cx231xx/built-in.o:/home/v4l/v4l/patchwork/drivers/media/video/cx231xx/cx231xx-417.c:401: first defined here
drivers/media/video/cx23885/built-in.o: In function `mc417_register_write':
/home/v4l/v4l/patchwork/drivers/media/video/cx23885/cx23885-417.c:324: multiple definition of `mc417_register_write'
drivers/media/video/cx231xx/built-in.o:/home/v4l/v4l/patchwork/drivers/media/video/cx231xx/cx231xx-417.c:343: first defined here
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gcc didn't like to have i++ inside a complex operation:
drivers/media/video/cx231xx/cx231xx-417.c: In function ‘cx231xx_load_firmware’:
drivers/media/video/cx231xx/cx231xx-417.c:1059: warning: operation on ‘i’ may be undefined
drivers/media/video/cx231xx/cx231xx-417.c:1061: warning: operation on ‘i’ may be undefined
drivers/media/video/cx231xx/cx231xx-417.c:1063: warning: operation on ‘i’ may be undefined
Btw, I agree with gcc, as we're using i and i++ at the same operation and,
depending on how optimization may occur, it may produce a wrong code.
While here, fix CodingStyle issues on the changed code.
Acked-by: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patches received from the vendor contained a lot of CodingStyle
issues. Cleans the style issues reported by checkpatch.pl on
those drivers.
It is better to do such style fixes when merging a big set of
changes than latter. Of course, the better is to receive patches
already cleaned ;)
Acked-by: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By default, tda18271 tries to optimize I2C bus by updating all registers
at the same time. Unfortunately, some devices doesn't support it.
The current logic has a problem when small_i2c is equal to 8, since there
are some transfers using 11 + 1 bytes.
Fix the problem by enforcing the max size at the right place, and allows
reducing it to max = 3 + 1.
Acked-by: Michael Krufky <mkrufky@kernellabs.com>
Acked-by: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Improves the logic, for it to be clearer and to avoid having
board-dependent config there.
Acked-by: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver has a field to indicate what bus is used by tuner and
by demod. However, this field were never used. On Pixelview,
it uses I2C 2 for tuner, instead of I2C 1.
drivers/media/video/cx231xx/cx231xx-cards.c
Acked-by: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/cx231xx/cx231xx-avcore.c:1608: warning: format ‘%d’ expects type ‘int’, but argument 3 has type ‘long unsigned int’
drivers/media/video/cx231xx/cx231xx-417.c:1047: warning: format ‘%d’ expects type ‘int’, but argument 3 has type ‘size_t’
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adjust the vblank and vactive counts so that they don't throw an error in
cx25840's set_std call (we did an equivalent change for NTSC when we got the
scaler working).
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx231xx_do_mode_ctrl_overrides() function was not touching the vactive line
count for PAL/SECAM modes, which in some use cases results in it being left in
the chip default state of 480 (NTSC).
Explicitly set the values, as is already done for NTSC.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix some indentation problems and remove an "if (1)" from the Colibri setup
function.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx231xx_set_Colibri_For_LowIF() function is only ever called if the tuner
has a DIF (see vidioc_s_frequency() in cx231xx-video.c). Hence, we do not
need to do a board specific check in this function.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code was deciding whether a DIF was present based on the board
profile. However, this is just another thing for someone to get wrong when
adding new boards. Make the decision based on the tuner instead, so that a
developer adding new boards only needs to specify which tuner the device has.
Of course, the first time somebody adds a board with a tuner other than xc5000
or tda18271, he/she will need to add another line for that tuner. But we
provide a friendly message in dmesg to let them know that.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Nobody is ever going to implement an i2c based IR controller on a bridge that
has an onboard universal IR receiver. This stuff was all copied from em28xx,
which has old enough versions of the chip that some didn't have onboard IR.
Remove the stubs related to i2c based IR (keeping the cx231xx-input code).
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move a printk() message which refers to enabling the cx23417 so that it only
shows up on a board that has the cx23417.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video grabber reference design (Veyron) does not have a tuner input, so
do not have it defined in the board profile.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Extend the board profile structure to allow configuration of the output mode.
Right now they are all doing VIP 1.1 format, but we have a board that needs
ITU656 format (which hasn't been checked in yet).
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add initial support for the Hauppauge USBLive 2 (2040:c200). Note that I
had to copy a bunch of the case statements used for the Conexant video grabber
reference design (which also doesn't have a tuner). This will likely need to
be refactored out into the board profile.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner is on i2c port 3 just like all the reference designs. Having it
improperly set to port #1 causes the tuner initialization to fail when enabling
the device.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If switching to a tuner input, reset the standard and tune to the last known
frequency. We need to do this in particular for this bridge since the tuner
gets powered down when captuing on the composite or s-video inputs.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove a hack which was jammed into s_input to force the device into bulk mode
at runtime (an abuse of the API). If this sort of functionality is actually
needed (aside from the existing "transfer_mode" modprobe variable), a patch
can be submitted which makes use of a private control.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Exeter hardware design does not use GPIOs to manage whether its in
digital mode or analog mode, but we need to setup the power control properly.
For that board, setup power control and remove the mux select call. It is
highly likely that this change could be used by other boards as well, which
would make power management cleaner (fixing known issues transitioning between
analog and digital mode).
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
You cannot call the video_mux routine from within the isoc setup, because that
code is shared with the digital isoc handler. This was causing the GPIOs and
power control to be put into the wrong state when starting up digital mode.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to clear out the field before setting individual bits, or else we end
up with a union of whatever was there and what we are trying to set. For
example, switching to digital mode ends up being 0x30 instead of 0x10 if we
were previously in analog tv mode.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the responsibility for setting up the horizontal and vertical scalers
entirely to the cx25840 driver. The cx231xx-avcore was actually programming
garbage into the HSCALE_CTRL and VSCALE_CTRL registers (because of differences
in how the em28xx driver worked, which the cx231xx driver was derived from).
The net effect is that the scaler now works properly (tested with both PAL
and NTSC under mplayer and tvtime).
This patch also gets rid of cx25840 errors showing up in dmesg which say
"720x480 is not a valid size" (since we now properly setup the size of the
active video area).
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the log level from info to debug for some log events that occur
frequently and should never need to be seen in normal operation.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no need for a switch statement here. Use the contents of the board
profile to dictate the tuner driver and i2c address. Eventually if a board
ever comes around which has a different i2c bus than #1, well that should be a
field in the board profile as well.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code was sending one videobuf per field (despite having specified
V4L2_FIELD_SEQ_TB during setup). As a result, application which used the
read() interface would work, except they would sometimes have the fields
reversed (depending on the luck of which field the device was on when the
application started VBI capture). The net effect was that CC decoding would
only work about 50% of the time.
Restructure the VBI code a bit so that works like all the other drivers, such
that both fields are delivered in a single videobuf buffer, which ensures that
they are always received in a predictable order.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The VBI sampling rate and offset were incorrectly specified, which resulted in
CC data not being rendered under zvbi or tvtime.
Set the fields correctly.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change a %x to a %p since the variable is a pointer
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Run Lindent and fix a few spacing issues.
This patch makes no functional change to the driver.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Configure the tda18271 to use a smaller transaction size by default, which
works around some sort of i2c bug in the Polaris driver (which needs to be
debugged).
This should be safe for other boards (being in tuner-core means it will be
enabled by default), although testing needs to be done.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix case where analog calls come in while the DVB side of the board is still
initializing. This patch is actually just an exact port of the same patch
made by Mauro to em28xx in hg rev 14762.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for various Hauppauge EXETER designs.
Note by DJH: fixed a few minor 'make checkpatch' warnings before commit.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce a new driver for the s5h1432
Signed-off-by: Palash Bandyopadhyay <palash.bandyopadhyay@conexant.com>
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows GStreamer to pick appropriate framerates and resolutions
based on desired capture parameters.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch, which basically reverts 6d77444ac, fixes an occasional
on-boot or on-capture hang on the XO-1 laptop.
It seems like the cafe hardware is flakier than we thought and that in
some cases, the commands get executed but are never reported as completed
(even if we substantially increase the delays before reading registers).
Reintroduce the 1-second CAFE_SMBUS_TIMEOUT to catch and avoid this
strange hardware bug.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As pointed by Laurent:
I think min_t(size_t, PAGE_SIZE, size) is the preferred way.
Thanks-to: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are some symbols at saa7134-input that are used on saa7134
and vice-versa. Due to that, module install fails.
So, partially revert commit 9f495cf7d691c99bf7bdcec9f35fcfdad2cf9ae9.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/videobuf-dma-sg.c: In function ‘videobuf_pages_to_sg’:
drivers/media/video/videobuf-dma-sg.c:119: warning: comparison of distinct pointer types lacks a cast
drivers/media/video/videobuf-dma-sg.c:120: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver sn9c102 does not know about the sensor mi0360b.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'end of image' block may be splitted between two ISOC packets.
This case was not tested, so, some images could be lost and concatenated
to previous one(s), raising 'frame overflow' errors.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Call to i2c_put_adapter was missing in radio_si4713_pdriver_probe and
radio_si4713_pdriver_remove.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We've been doing this for a while in Fedora without any complaints.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of doing:
[ 82.581639] tda18271 4-0060: creating new instance
[ 82.588411] Unknown device detected @ 4-0060, device not supported.
[ 82.594695] tda18271_attach: [4-0060|M] error -22 on line 1272
[ 82.600530] tda18271 4-0060: destroying instance
Print:
[ 468.740392] Unknown device (0) detected @ 4-0060, device not supported.
for the error message, to help detecting what's going wrong with the
device.
This helps to detect when the driver is using the wrong I2C bus (or have
the i2g gate switch pointing to the wrong place), on devices like cx231xx
that just return 0 on reads to a non-existent i2c device.
Reviewed-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function is an internal API and belongs in v4l2-common.h, not
videodev.h. The return pointer and probe argument should be const as well.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Missed a few init functions on non-Intel platforms the first time :-(
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With a null request byte, these commands prevented the next commands
to be executed.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Multiple user-space application instances can open the same video device, but
it only makes sense for one of them to manage the videobuffer queue and set
video format of the device. Restrict soc-camera respectively.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many video drivers implement a fixed set of frame formats and thus face a task
of finding the best match for a user-requested format. Implementing this in a
generic function has also an advantage, that different drivers with similar
supported format sets will select the same format for the user, which improves
consistency across drivers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows userspace to terminate a capture without waiting for the current
frame to complete.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the current source status the emma has no limitation for any PIXFMT
since the data is parsed raw and unprocessed into the memory.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L1 is deprecated and will be removed completely soon.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The initial em28xx std (PAL) was not passed on to the subdevs. This led to
these tvp5150 kernel log errors when running v4l2-ctl --all:
tvp5150 0-005c: VBI can't be configured without knowing number of lines
The reason was that tvp5150 was still using its own internal default: STD_ALL.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf_waiton() must unlock and relock ext_lock if it has to wait.
For that to happen it needs the videobuf_queue pointer.
Don't attempt to unlock/relock q->ext_lock unless it was locked in the
first place.
vb->state has to be protected by a spinlock to be safe.
This patch is based on code from Mauro Carvalho Chehab <mchehab@redhat.com>.
[mchehab@redhat.com: add extra argument to a few missing places]
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an ext_lock argument to the videobuf init functions. This allows
drivers to pass the vdev->lock pointer (or any other externally held lock)
to videobuf. For now all drivers just pass NULL.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently videobuf uses the vb_lock mutex to lock its data structures.
But this locking will (optionally) move into the v4l2 core, which means
that in that case vb_lock shouldn't be used since the external lock is already
held.
Prepare for this by adding a pointer to such an external mutex and
don't lock if that pointer is set.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers can optionally set a pointer to a mutex in struct video_device.
The core will use that to lock before calling open, read, write, unlocked_ioctl,
poll, mmap or release.
Updated the documentation as well and ensure that v4l2-event knows about the
lock: it will unlock it before doing a blocking wait on an event and relock it
afterwards.
Ensure that the 'video_is_registered' check is done when the lock is held:
a typical disconnect will take the lock as well before unregistering the
device nodes, so to prevent race conditions the video_is_registered check
should also be done with the lock held.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Until now all fops except release and (unlocked_)ioctl returned an error
after the device node was unregistered. Extend this as well to the ioctl
fops. There is nothing useful that an application can do here and it
complicates the driver code unnecessarily.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver author seems to not worked on this driver since its conversion
from 2.2 to 2.4. Nobody is known to have a stradis hardware for testing. As
it still uses V4L1 API, BKL and probably some other old stuff, someone would
need to work on it to preserve the driver. Instead of investing time and
efforts to keep porting it to work with new API's, it seems better to just
drop the driver.
So, let's move it to drivers/staging and label it to die at 2.6.38, if nobody
cares enough to port parallel port support to gspca or to create a new driver
that uses the same gspca-cpia sub-driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cpia driver were re-written inside gspca driver, for USB devices. The only
functionality that were not migrated is the support for parallel port,
as:
1) the developer didn't find any hardware;
2) it doesn't seem important to keep support for a parallel port webcam,
as this is an obsolete technology;
3) the changes at gspca for it to work with parallel port would be very large;
4) this driver still uses BKL.
So, let's move it to drivers/staging and label it to die at 2.6.38, if nobody
cares enough to port parallel port support to gspca or to create a new driver
that uses the same gspca-cpia sub-driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are a few ancillary static routines used by ioctl functions
that takes bttv lock internally. As we'll be adding the same lock
for all ioctl's that need, we need to properly document them, to
avoid doing double locks
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mpc512x kernel configurations without SPI support do not build:
drivers/media/video/fsl-viu.c: In function 'viu_open':
drivers/media/video/fsl-viu.c:1248: error: implicit declaration of function 'kzalloc'
drivers/media/video/fsl-viu.c:1248: warning: assignment makes pointer from integer without a cast
drivers/media/video/fsl-viu.c: In function 'viu_release':
drivers/media/video/fsl-viu.c:1335: error: implicit declaration of function 'kfree'
If CONFIG_SPI is enabled, the slab.h will be included in
linux/spi/spi.h which is included by media/v4l2-common.h
and the fsl_viu.c driver builds.
Let's incluce linux/slab.h directly to fix the build breakage.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bt8xx driver only uses the big kernel lock in its dst_ca_ioctl
function and never to serialize against other code, so we can
trivially replace it with a private mutex.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dvb core only uses the big kernel lock in the open
and ioctl functions, which means it can be replaced with
a dvb specific mutex. Fortunately, all the ioctl functions
go through dvb_usercopy, so we can move the serialization
in there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just fill the array as necessary and terminate with 0
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Code in function cx22702_set_tps() can be slightly simplified.
Apparently gcc was smart enough to optimize it anyway, but it can't
hurt to make the code more readable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The init sequence never changes so it can be marked const. Likewise,
cx22702_ops is a template and can thus be made read-only.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Calling the same functions in if/else or switch/case branches is
inefficient. Refactor the code for a smaller binary and increased
readability.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows the removal of CONFIG_INPUT from saa7134, and
helps to create a better Kconfig dependency hierarchy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tda8425 initialization function sets up the inputmap for riva boards.
After some digging I discovered that this was for the V4L rivatv driver
that is found on sourceforge. This driver hasn't been maintained since the
last 5 years and will no longer work with the current v4l framework.
So we can safely remove this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These variables are either unconditionally set right afterward, or
already set to 0 by kzalloc.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get rid of init_MUTEX[_LOCKED]() and use sema_init() instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, they get set up with the pad keytable, which they can't
actually use at all. Also add another variant of volume scancodes from
another 0xffdc device, and properly set up the 0x9e 0xffdc device as an
iMON VFD w/MCE proto IR.
Based on data and a prior patch from Anders Eriksson on the lirc list.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lest we get our keycodes wrong... Thus far, in practice, I've not found
it to actually matter, but its one of the issues raised in
https://bugzilla.kernel.org/show_bug.cgi?id=16351 that wasn't addressed
by converting to using native IR keydown/up functions.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a stab at separating the mouse (and front panel/knob) events
out to a separate input device. This is necessary in preparation for
the next patch which makes the rc-core input dev opaque to rc
drivers.
I can't verify the correctness of the patch beyond the fact that it
compiles without warnings. The driver has resisted most of my
attempts at understanding it properly...for example, the double calls
to le64_to_cpu() and be64_to_cpu() which are applied in
imon_incoming_packet() and imon_panel_key_lookup() would amount
to a bswab64() call, irregardless of the cpu endianness, and I think
the code wouldn't have worked on a big-endian machine...
- Minor alterations to apply with minimal core IR changes
- Use timer for imon keys too, since its entirely possible for the
receiver to miss release codes (either by way of another key being
pressed while the first is held or by the remote pointing away from
the recevier when the key is release. yes, I know, its ugly).
- Bump driver version number, since this is a fairly significant change
(for the much much better).
Tested successfully w/an imon knob receiver.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The imon driver currently reimplements its own version of ir_keyup
(along with key release timer functionality also already present in the
core IR code). A follow-up imon patch will make use of ir_keyup and the
IR stack's key release code.
Trivial extraction from David Härdeman's pending rc-core merge and
device interface abstraction patchset to facilitate merging a patch
based on his imon input dev split patch ahead of the larger churn, which
is slated for post-2.6.37-rc1 (after Dmitry's large keycode patches are
merged in mainline).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only reason for keeping I2C_HW_SAA7134 is to allow setting a
per-device polling interval. Just move this info to the platform
data, allowing drivers to change it per device, where needed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the cx88 specific initialization for Hauppauge XVR remotes
into cx88-input, removing the need for test it inside ir-kbd-i2c.
The reference at cx88 for this symbol, at:
drivers/media/video/cx88/cx88-i2c.c: core->i2c_adap.id = I2C_HW_B_CX2388x;
drivers/media/video/cx88/cx88-vp3054-i2c.c: vp3054_i2c->adap.id = I2C_HW_B_CX2388x;
Can't be removed yet, since lirc-i2c still uses it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Removed the BKL from usbvision.
There was an initialization bug as well where the i2c bus was registered twice.
Although when the BKL was present no oops was generated, I did run into
other i2c problems. Now that I protect against duplicate i2c registration
that bug is now gone as well.
But trying to disconnect the USB cable while someone is still using the device
still leads to a crash.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove a hack in the tuner code for the mxb board. This hack is no longer
needed since the tuner is now probed on its correct address as specified
by the mxb driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the V4L1 API from this driver, making it fully V4L2.
Also fix a bug where the /dev/videoX device was created too early, which led
to initialization problems of the camera, making it unable to capture video.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The illuminator controls should only be available to the user for the Intel
Play QX3 microscope. The implementation to inhibit the controls is intended to
be consistent with the other gspca driver implementations.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Turn the lights of the QX3 on (or off) as needed when resuming and at module load.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds basic V4L2 controls for the illuminators on the Intel
Play QX3 microscope.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some media devices (microscopes) may have one or many illuminators.
This patch makes them controlable by the applications.
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When compressed, the images take less than one byte per pixel.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove HID and polling via firmware API. Implement direct access to remote codes via memory read and write.
HID and polling via firmware api never worked 100% well and there was also some limitations which tied used remote and device together.
After that it is possible to use upcoming kernel remote controller core.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Detect TerraTec Cinergy T Stick Dual RC remote config using device
USB ID instead of device EEPROM hash. It was found that there is
devices with slightly different EEPROM content...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID [0ccd:0099] for TerraTec Cinergy T Stick Dual RC.
Device is based for AF9015 + AF9013 + 2 x MxL5007T chips.
Thanks to the TerraTec!
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 490ade7e3f4474f626a8f5d778ead4e599b94fbc merge conflict fix
leads situation where last nine device definitions were overridden mistakenly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the vtx (aka videotext aka teletext) API from the v4l2 core.
This API was scheduled for removal in kernel 2.6.35.
The vtx device nodes have been superseded by vbi device nodes
for many years. No applications exist that use the vtx support.
Of the two i2c drivers that actually support this API the saa5249
has been impossible to use for a year now and no known hardware
that supports this device exists. The saa5246a is theoretically
supported by the old mxb boards, but it never actually worked.
In summary: there is no hardware that can use this API and there
are no applications actually implementing this API.
The vtx support still reserves minors 192-223 and we would really
like to reuse those for upcoming new functionality. In the unlikely
event that new hardware appears that wants to use the functionality
provided by the vtx API, then that functionality should be build
around the sliced VBI API instead.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These old i2c teletext drivers are not supported by any hardware and cannot be
tested anymore.
Note that while the mxb board seemingly used the saa5246a driver, in reality
this teletext driver never worked.
These drivers are removed as part of the vtx feature removal, originally
scheduled for 2.6.35.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
bit 3(LK) indicates that the Vstatus is locked.
Currently using bit 7(CF) which is usually present, results in early
aborted search in FEC_AUTO and missing channels.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
WARNING: please, no space before tabs
+ * ^IPOR = Power on Reset (VCC H=<2.2v L=>2.2v)$
WARNING: unnecessary whitespace before a quoted newline
+ deb_info("Frq=%d x=%d N=%d A=%d \n", frequency, x, N, A);
WARNING: please, no space before tabs
+^Ielse ^I^I/*frequency up to 2150000*/$
WARNING: unnecessary whitespace before a quoted newline
+ deb_info("Data 0=[%x%x%x%x] \n", data[0], data[1], data[2], data[3]);
WARNING: unnecessary whitespace before a quoted newline
+ deb_info("Data 2=[%x%x] \n", data[2], data[3]);
Cc: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tuner used in Sharp BS2F7VZ7395 dvbs module.
When ix2505v tuner is attached to stv0288 form this module.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The same expression is tested twice and the result is the same each time.
The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@expression@
expression E;
@@
(
* E
|| ... || E
|
* E
&& ... && E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the NULL test is necessary, the initialization involving a dereference of
the tested value should be moved after the NULL test.
The sematic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adding the USB ID for my TerraTec Electronic GmbH Cinergy T RC MKII
[0ccd:0097] and hooking it up into af9015, on top of your new NXP TDA18218
patches, makes it work for me.
Just the shipped IR remote control doesn't seem to create keycode events
yet (tested with different remote=%d parameters), are there any hints to
add support for that?
[ 2.250022] usb 1-10: new high speed USB device using ehci_hcd and address 5
[ 2.369287] usb 1-10: New USB device found, idVendor=0ccd, idProduct=0097
[ 2.369290] usb 1-10: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.369293] usb 1-10: Product: USB2.0 DVB-T TV Stick
[ 2.369294] usb 1-10: Manufacturer: NEWMI
[ 2.369296] usb 1-10: SerialNumber: 010101010600001
[ 2.534023] usbcore: registered new interface driver hiddev
[ 2.537235] input: NEWMI USB2.0 DVB-T TV Stick as /devices/pci0000:00/0000:00:02.1/usb1/1-10/1-10:1.1/input/input0
[ 2.537323] generic-usb 0003:0CCD:0097.0001: input,hidraw0: USB HID v1.01 Keyboard [NEWMI USB2.0 DVB-T TV Stick] on usb-0000:00:02.1-10/input1
[ 2.537349] usbcore: registered new interface driver usbhid
[ 2.537351] usbhid: USB HID core driver
[ 3.263177] generic-usb 0003:04D9:1603.0002: input,hidraw1: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:02.0-8.1/input0
[ 3.286946] generic-usb 0003:04D9:1603.0003: input,hidraw2: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:02.0-8.1/input1
[ 3.467136] generic-usb 0003:046D:C050.0004: input,hidraw3: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-8.2/input0
[ 3.660890] generic-usb 0003:10D5:000D.0005: input,hidraw4: USB HID v1.10 Keyboard [No brand SP02-A1] on usb-0000:00:02.0-8.3/input0
[ 5.567632] dvb-usb: found a 'TerraTec Cinergy T Stick RC' in cold state, will try to load a firmware
[ 5.693497] dvb-usb: downloading firmware from file 'dvb-usb-af9015.fw'
[ 5.773109] dvb-usb: found a 'TerraTec Cinergy T Stick RC' in warm state.
[ 5.773168] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[ 5.774290] DVB: registering new adapter (TerraTec Cinergy T Stick RC)
[ 6.007696] af9013: firmware version:5.1.0
[ 6.010843] DVB: registering adapter 0 frontend 0 (Afatech AF9013 DVB-T)...
[ 6.032697] tda18218: NXP TDA18218HN successfully identified.
[ 6.034442] dvb-usb: TerraTec Cinergy T Stick RC successfully initialized and connected.
[ 6.040612] usbcore: registered new interface driver dvb_usb_af9015
[mchehab@redhat.com: Fix merge conflict with another board addition]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Making static data const avoids allocation of additional r/w memory and
reduces initialisation time. It also provides some additional opportunities
for compiler optimisations.
Signed-off-by: Lawrence Rust <lvr@softsystem.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/cx88/cx88-dsp.c: In function ‘detect_a2_a2m_eiaj’:
drivers/media/video/cx88/cx88-dsp.c:158: warning: ‘carrier_freq’ may be used uninitialized in this function
drivers/media/video/cx88/cx88-dsp.c:158: warning: ‘stereo_freq’ may be used uninitialized in this function
drivers/media/video/cx88/cx88-dsp.c:158: warning: ‘dual_freq’ may be used uninitialized in this function
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace direct access to the v4l2_subdev priv field with the inline
v4l2_get_subdevdata method.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using an enum and removing the default case from switch statements accessing
the value enables the compiler to emit a warning (enabled with -Wall) when an
audio mode is not handled.
This highlights an omission in the function cx88_dsp_detect_stereo_sap()
(in cx88-dsp.c) not handling WW_EIAJ and WW_M.
Signed-off-by: Lawrence Rust <lawrence@softsystem.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Error codes are stored in rc, but the return value is always 0. Return rc
instead.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
local idexpression x;
constant C;
@@
if (...) { ...
x = -C
... when != x
(
return <+...x...+>;
|
return NULL;
|
return;
|
* return ...;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In each case, error codes are stored in rc, but the return value is always
0. Return rc instead.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
local idexpression x;
constant C;
@@
if (...) { ...
x = -C
... when != x
(
return <+...x...+>;
|
return NULL;
|
return;
|
* return ...;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Error codes are stored in res, but the return value is always 0. Return
res instead.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
local idexpression x;
constant C;
@@
if (...) { ...
x = -C
... when != x
(
return <+...x...+>;
|
return NULL;
|
return;
|
* return ...;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In cx23885/cx23885-video.c, cx88/cx88-video.c, davinci/vpif_capture.c, and
davinci/vpif_display.c, group the aligned code into a single if branch.
In saa7134/saa7134-video.c, outdent the code following the if.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"sd" and "err" are too common names to be used in macros for local variables.
Prefix them with an underscore to avoid name clashing.
[mchehab@redhat.com: whitespace cleanups]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes in-kernel decoding with the stock Streamzap PC Remote
work out of the box. There are quite a few things going on in this
patch, all related to getting this working:
1) I had to enable reporting of a long space at the end of each signal,
or I had weird buffering and keybounce issues.
2) The keymap has been reworked slightly to match actual decoded values,
the first edition was missing the pre-data bits present in the lirc
config file for this remote.
3) There's a whole new decoder included, specifically for the
not-quite-RC5 15-bit protocol variant used by the Streamzap PC
Remote. The decoder, while usable with other recievers (tested with
an mceusb receiver), will only be loaded by the streamzap driver, as
its likely not of use in almost all other situations. This can be
revisited if/when all keytable loading (and disabling of unneeded
protocol decoder engines) is moved to userspace, but for now, I think
this makes the most sense.
Note that I did try to enable handling the streamzap RC5-ish protocol in
the current RC5 decoder, but there's no particularly easy way to tell if
its 14-bit RC5 or 15-bit Streamzap until we see bit 14, and even then,
in testing an attempted decoder merge, only 2/3 of the keys were
properly recognized as being the 15-bit variant and decoded correctly,
the rest were close enough to compliant with 14-bit that they were
decoded as such (but they have overlap with one another, and thus we
can't just shrug and use the 14-bit decoded values).
Also of note in this patch is the removal of the streamzap driver's
internal delay buffer. Per discussion w/Christoph, it shouldn't be
needed by lirc any longer anyway, and it doesn't seem to make any
difference to the in-kernel decoder engine. That being the case, I'm
yanking it all out, as it greatly simplifies the driver code.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/gspca/konica.c: In function ‘sd_start’:
drivers/media/video/gspca/konica.c:322: error: implicit declaration of function ‘usb_buffer_alloc’
drivers/media/video/gspca/konica.c:325: warning: assignment makes pointer from integer without a cast
make[3]: ** [drivers/media/video/gspca/konica.o] Erro 1
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_xirlink_cit: adjust ibm netcam pro framerate for available bandwidth
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This new driver replaces the (known to not work / crash) usbvideo konicawc
driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_*: correct typo in my email address in various subdrivers
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mark usbvideo ibmcam driver as deprecated, it is replaced by the new
gscpa xirlink_cit driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some xirlink_cit models have only 1 alt setting, but the actual used
bandwidth can be programmed through a register use this to allow streaming
while other isoc streams (for example sound) are active at the same time.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_xirlink_cit: Use alt setting -> fps formula for model 1 cams too
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for camera with a bcd version of 0.01, I've dupped these
Model0 cams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note this is untested as I don't have hardware to test, but all
initsequences were taken over 1 on 1 from the old ibmcam driver so things
should work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The old usbvideo ibmcam driver needs to be replaced with a v4l2 driver
preferably using the gspca webcam framework rather then the old usbvideo
framework.
This new gspca sub driver sets a first step in that direction. The ibmcam
driver supports 4 different model webcams. This new driver (for now) only
supports Model 3 cameras, as my test cam is a Model 3 cam, or so I thought.
Upon reading:
http://www.linux-usb.org/ibmcam/
I learned that the IBM Netcamera Pro I have even though having the same
usb id and the same bcd version is different from the Model 3 cameras
supported by the ibmcam driver. So this new gscpa subdriver supports Model 3
cameras (untested), and the IBM Netcamera Pro. Currently use with the
IBM Netcamera Pro requires a module parameter. I hope to be able to
autodetect which is which in the future.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dabusb device driver is sufficiently serialized using
its own mutex, no need for the big kernel lock here
in addition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
The dvb core only uses the big kernel lock in the open
and ioctl functions, which means it can be replaced with
a dvb specific mutex. Fortunately, all the ioctl functions
go through dvb_usercopy, so we can move the serialization
in there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: linux-media@vger.kernel.org
The bt8xx driver only uses the big kernel lock in its dst_ca_ioctl
function and never to serialize against other code, so we can
trivially replace it with a private mutex.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-media@vger.kernel.org
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The compat code for the VIDIOCSMICROCODE ioctl is totally buggered.
It's only used by the VIDEO_STRADIS driver, and that one is scheduled to
staging and eventually removed unless somebody steps up to maintain it
(at which point it should use request_firmware() rather than some magic
ioctl). So we'll get rid of it eventually.
But in the meantime, the compatibility ioctl code is broken, and this
tries to get it to at least limp along (even if Mauro suggested just
deleting it entirely, which may be the right thing to do - I don't think
the compatibility translation code has ever worked unless you were very
lucky).
Reported-by: Kees Cook <kees.cook@canonical.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
In case of error during probe() the driver calls free_irq() function
on not yet allocated irq. This patches fixes the call sequence in case of
the error.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When a driver that uses videobuf-dma-contig is used with the USERPTR
memory access method a kernel oops might happen: a NULL address may be
passed to dma_free_coherent(). This happens when an application calls
REQBUFS and then exits without queuing any buffers. This patch fixes
that bug.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For some cards, ir_dev->props and ir_dev->raw are both NULL. These cards are
using built-in IR decoding instead of raw, and can't easily be made to switch
protocols.
So upon reading /sys/class/rc/rc?/protocols on such a card, return 'builtin' as
the supported and enabled protocol. Return -EINVAL on any attempts to change
the protocol. And most important of all, don't crash.
Signed-off-by: Brian Rogers <brian@xyzw.org>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix DMA engine pixel offset calculation for 3-planar YUV formats.
On S5PV210 SoCs horizontal offset is applied as number of pixels,
not bytes per line.
[mchehab@redhat.com: CodingStyle cleanup]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At all frame rates except 30fps and 5fps the camera produces very dark
pictures. Auto-exposure is probably disabled by the camera at all frame
rates except 30fps, making them pretty unusable.
Work around the problem by introducing a new RESTRICT_FRAME_RATE quirk
that disables all the frame rates except the default one.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera requires the STREAM_NO_FID quirk. Add a corresponding entry
in the device IDs list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The FBIOGET_VBLANK device ioctl allows unprivileged users to read 16
bytes of uninitialized stack memory, because the "reserved" member of
the fb_vblank struct declared on the stack is not altered or zeroed
before being copied back to the user. This patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The wrong value for the volume control limit, 65335 vs. 65535,
prevents proper cx25840 v4l2_subdevice initialization.
Reported-by: Igor M. liplianin <liplianin@me.by>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Video device was not being released on driver remove.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Output buffer has to be at least the size of input buffer, not the other
way around.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The drivers/media/video/mt9v022.c file, on line 405, tries a "case 0" o a
v4l2_mbus_pixelcode enum which don't have an 0 value element, so I got a compile
warning. That "case" is useless so it can be removed.
Signed-off-by: Ionut Gabriel Popescu <poyo_vl@yahoo.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mx25_camera_irq irq handler may get called after the camera has been
deactivated (from mx2_camera_deactivate). Detect this situation, and bail out.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the end of frame marker does not contain any pixel, it must not be
transferred.
Reported-by: Ivo Jager <ivo.jager@siliconfields.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes a nasty memory corruption bug when using userptr I/O.
The function videobuf_pages_to_sg() sets up the scatter-gather list for the
DMA transfer to the userspace pages. The first transfer is setup correctly
(the size is set to PAGE_SIZE - offset), but all other transfers have size
PAGE_SIZE. This is wrong for the last transfer which may be less than PAGE_SIZE.
Most, if not all, drivers will program the boards DMA engine correctly, i.e.
even though the size in the last sg element is wrong, they will do their
own size calculations and make sure the right amount is DMA-ed, and so seemingly
prevent memory corruption.
However, behind the scenes the dynamic DMA mapping support (in lib/swiotlb.c)
may create bounce buffers if the memory pages are not in DMA-able memory.
This happens for example on a 64-bit linux with a board that only supports
32-bit DMA.
These bounce buffers DO use the information in the sg list to determine the
size. So while the DMA engine transfers the correct amount of data, when the
data is 'bounced' back too much is copied, causing buffer overwrites.
The fix is simple: calculate and set the correct size for the last sg list
element.
Signed-off-by: Hans Verkuil <hans.verkuil@tandberg.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers shouldn't sleep while holding a spinlock. A previous workaround
were to release the spinlock before callinc schedule().
This patch uses a different approach: it just waits for the
siano hardware to answer.
Signed-off-by: Richard Zidlicky <rz@linux-m68k.org>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To improve performance on DiB7770-devices enabling the current mirror
is needed.
This patch adds an option to the dib7000p-driver to do that and it
creates a separate device-entry in dib0700-device to use those changes
on hardware which is using the DiB7770.
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These keys are found on remote bundled with
Toshiba Qosmio F50-10q.
Found and tested by, Sami R <maesesami@gmail.com>
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The logic in ir_timer_keyup was inverted.
In case that values aren't equal,
the meaning of the time_is_after_eq_jiffies(ir->keyup_jiffies) is that
ir->keyup_jiffies is after the the jiffies or equally that
that jiffies are before the the ir->keyup_jiffies which is
exactly the situation we want to avoid (that the timeout is in the future)
Confusing Eh?
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Anton Blanchard <anton@samba.org>, double IR events on
2.6.36-rc2 and a DViCO FusionHDTV DVB-T Dual Express are happening:
[ 1351.032084] ir_keydown: i2c IR (FusionHDTV): key down event, key 0x0067, scancode 0x0051
[ 1351.281284] ir_keyup: keyup key 0x0067
ie one key down event and one key up event 250ms later.
So, we need to increase the repeat timeout, to avoid this bug to hit.
As we're doing it at core, this fix is not needed anymore at dib0700 driver.
Thanks-to: Anton Blanchard <anton@samba.org>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Carlos, Prolink Pixelview SBTVD Hybrid is based on
Conexant cx231xx + Fujitsu 86A20S demodulator. However, both shares
the same USB ID. So, we need to use USB bcdDevice, in order to
properly discover what's the board.
We know for sure that bcd 0x100 is used for a dib0700 device, while
bcd 0x4001 is used for a cx23102 device. This patch reserves two ranges,
the first one from 0x0000-0x3f00 for dib0700, and the second from
0x4000-0x4fff for cx231xx devices.
This may need fixes in the future, as we get access to other devices.
Thanks-to: Carlos Americo Domiciano <c_domiciano@yahoo.com.br>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reported in lirc sf.net tracker and on lirc mailing list
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When plugging some webcams on ARM, the system crashes.
This is because we alloc buffer for an urb through usb_buffer_alloc,
the alloced buffer is already in DMA coherent region, so we should
set the flag of this urb to URB_NO_TRANSFER_DMA_MAP, otherwise when
we submit this urb, the hcd core will handle this address as an
non-DMA address and call dma_map_single/sg to map it. On arm
architecture, dma_map_single a DMA coherent address will be catched
by a BUG_ON().
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some time a go our customers wrote me about problem with our TV card
BeholdTV Columbus. It's PCMCIA TV card for notebook.
As I understand v4l has some regression with autodetect address of tuners.
I can set incorrect I2C address and had report about detect tuner. No any TV of course.
When I set correct tuner type and I2C address of the tuners all works well.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original code dereferenced "port" before checking it for NULL. I
moved the test down below the check. Also I changed the comparisons a
little so people wouldn't get confused and think "port" and "buf" were
ints instead of pointers. (Probably that's what lead to this issue in
the first place.)
There is only one caller for this function and it passes non-NULL
pointers, so this is essentially a cleanup rather than a bugfix.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We dereference "maskptr" unconditionally at the start of the function
and also inside the call to parse_tlist() towards the end of the
function. This function is called from store_val_any() and it always
passes a non-NULL pointer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"fw" is always a non-NULL pointer at this point, and anyway
release_firmware() accepts NULL pointers.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original code dereferenced ir->raw after freeing it and setting it
to NULL.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If we return directly here then we miss out on some mutex_unlock()s
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx88-alsa module has been around since January 2006 and has seen no
significant changes since September 2007. It is stable in operation
and so I believe that the 'experimental' tag is no longer warranted.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There does not seem to be a need for lirc to
allow seeking on the file descriptor, so let's
just disallow this before users start relying
on it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Switch the code to use new style of getkeycode and setkeycode
methods to allow retrieving and setting keycodes not only by
their scancodes but also by index.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This build bug triggers:
drivers/built-in.o: In function `mantis_exit':
(.text+0x377413): undefined reference to `ir_input_unregister'
drivers/built-in.o: In function `mantis_input_init':
(.text+0x3774ff): undefined reference to `__ir_input_register'
If MANTIS_CORE is enabled but IR_CORE is not. Add the correct
dependency.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are no more users of struct file_operations:ioctl. These
can be safely removed.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: John Kacur <jkacur@redhat.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB: v4l2-ctrls.c: needs to include slab.h
V4L/DVB: fix Kconfig to depends on VIDEO_IR
V4L/DVB: Fix IR_CORE dependencies
v4l2-ctrls.c needs to include slab.h to prevent build errors:
drivers/media/video/v4l2-ctrls.c:766: error: implicit declaration of function 'kzalloc'
drivers/media/video/v4l2-ctrls.c:786: error: implicit declaration of function 'kfree'
drivers/media/video/v4l2-ctrls.c:1528: error: implicit declaration of function 'kmalloc'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: I2C bus multiplexer driver pca954x
i2c: Multiplexed I2C bus core support
i2c: Use a separate mutex for userspace client lists
i2c: Make i2c_default_probe self-sufficient
i2c: Drop dummy variable
i2c: Move adapter locking helpers to i2c-core
V4L/DVB: Use custom I2C probing function mechanism
i2c: Add support for custom probe function
i2c-dev: Use memdup_user
i2c-dev: Remove unnecessary kmalloc casts
Now that i2c-core offers the possibility to provide custom probing
function for I2C devices, let's make use of it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The probe method used by i2c_new_probed_device() may not be suitable
for all cases. Let the caller provide its own, optional probe
function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (94 commits)
V4L/DVB: tvp7002: fix write to H-PLL Feedback Divider LSB register
V4L/DVB: dvb: siano: free spinlock before schedule()
V4L/DVB: media: video: pvrusb2: remove custom hex_to_bin()
V4L/DVB: drivers: usbvideo: remove custom implementation of hex_to_bin()
V4L/DVB: Report supported QAM modes on bt8xx
V4L/DVB: media: ir-keytable: null dereference in debug code
V4L/DVB: ivtv: convert to the new control framework
V4L/DVB: ivtv: convert gpio subdev to new control framework
V4L/DVB: wm8739: convert to the new control framework
V4L/DVB: cs53l32a: convert to new control framework
V4L/DVB: wm8775: convert to the new control framework
V4L/DVB: cx2341x: convert to the control framework
V4L/DVB: cx25840: convert to the new control framework
V4L/DVB: cx25840/ivtv: replace ugly priv control with s_config
V4L/DVB: saa717x: convert to the new control framework
V4L/DVB: msp3400: convert to the new control framework
V4L/DVB: saa7115: convert to the new control framework
V4L/DVB: v4l2: hook up the new control framework into the core framework
V4L/DVB: Documentation: add v4l2-controls.txt documenting the new controls API
V4L/DVB: v4l2-ctrls: Whitespace cleanups
...
To avoid more patches, I also fixed other spelling
and grammar bugs when they were in the same or
following line:
successfull -> successful
parse -> parses
controler -> controller
controlers -> controllers
Cc: Jiri Kosina <trivial@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
H-PLL Feedback Divider LSB register is an 8 bit register out
of which the first 4 bits are reserved. Current code is
writing to these reserved location. This patch corrects
this issue by left shifting the values being written to the
register by 4.
This patch has been tested on DM6467 EVM with 720P-60 and
1080I-60 inputs.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Calling schedule() holding spinlock with disables irqs is improper. As
spinlock protects list coredev->buffers, it can be unlocked untill wakeup.
This bug was introduced in a9349315f6.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Here a small patch to get a TwinHan VT DST DVB-T card working with
kernels >= 2.6.32. Analogously to
http://linuxtv.org/hg/v4l-dvb/rev/0e735b509163 I had to:
"Fill in the .caps field in struct dst_dvbt_ops (around line 1763) with
all the supported QAM modulation methods to match the capabilities of
the card as implemented in function dst_set_modulation (around line
502). Note that beginning with linux kernel version 2.6.32 the
modulation method is checked (by function dvb_frontend_check_parameters
in file drivers/media/dvb/dvb-core/dvb_frontend.c) and thus tuning fails
if you use a modulation method that is not present in the .caps field."
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"ir_dev->props" can be NULL. We only use raw mode if "ir_dev->props" is
non-NULL and "ir_dev->props->driver_type == RC_DRIVER_IR_RAW".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since this module is also used by drivers that are not yet converted, the old
and new code have to co-exist.
The source is split into three parts: a common part at the top, which is used
by both old and new code, then the old code followed by the new control
framework implementation. This new code is much more readable (and shorter!)
than the original code.
Once all bridge drivers that use this are converted the old code can be
deleted.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx25840 used a private control CX25840_CID_ENABLE_PVR150_WORKAROUND
to be told whether to enable a workaround for certain pvr150 cards.
This is really config data that it needs to get at load time.
Implemented this in cx25840 and ivtv.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the calls needed to automatically merge subdev controls into a bridge
control handler.
Hook up the control framework in __video_ioctl2 and video_register_device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To make it easier to determine whether all controls are added in v4l2-ctrls.c
the case statements inside the switch are re-ordered to match the header.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a new framework to handle controls which makes life for driver
developers much easier.
Note that this patch moves some of the control support that used to be in
v4l2-common.c to v4l2-ctrls.c. The tables were copied unchanged. The body
of v4l2_ctrl_query_fill() was copied to a new v4l2_ctrl_fill() function
in v4l2-ctrls.c. This new function doesn't use the v4l2_queryctrl
struct anymore, which makes it more general.
The remainder of v4l2-ctrls.c is all new. Highlights include:
- No need to implement VIDIOC_QUERYCTRL, QUERYMENU, S_CTRL, G_CTRL,
S_EXT_CTRLS, G_EXT_CTRLS or TRY_EXT_CTRLS in either bridge drivers
or subdevs. New wrapper functions are provided that can just be plugged in.
Once everything has been converted these wrapper functions can be removed as well.
- When subdevices are added their controls can be automatically merged
with the bridge driver's controls.
- Most drivers just need to implement s_ctrl to set the controls.
The framework handles the locking and tries to be as 'atomic' as possible.
- Ready for the subdev device nodes: the same mechanism applies to subdevs
and their device nodes as well. Sub-device drivers can make controls
local, preventing them from being merged with bridge drivers.
- Takes care of backwards compatibility handling of VIDIOC_S_CTRL and
VIDIOC_G_CTRL. Handling of V4L2_CID_PRIVATE_BASE is fully transparent.
CTRL_CLASS controls are automatically added.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Moved mt9m111_init after the chip version detection passage: I
don't like the idea of writing on a device we haven't identified
yet.
Signed-off-by: Philipp Wiesner <p.wiesner@phytec.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added this info to Kconfig and mt9m111.c, some comment cleanup,
replaced 'mt9m11x'-statements by clarifications or driver name.
Driver is fully compatible to mt9m131 which has only additional functions
compared to mt9m111. Those aren't used anyway at the moment.
Signed-off-by: Philipp Wiesner <p.wiesner@phytec.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The emma uses bufnum 1 and 0. This patch tells the bufqueue to change
the next buffer to the next one and not the current one.
Otherwise the BUG_ON above will trigger everytime.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tuner, DVB frontend and video helper chip drivers are by default
autoselected by their respective host cards, this, however, doesn't make
much sense on SoC-based systems. Disable autoselection on EMBEDDED
systems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no sense in trying to set cropping if we cannot get current one
from the host driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The exchanges for sensor mt9v111 are different with bridges zc301 and zc303.
The exchanges for the bridge zc303 were those of the bad named tas5130ck.
These mt9v111 exchanges have been adjusted from the ms-Windows public files
vm30x.inf (for 0ac8:301b) and usbvm303.inf (for 0ac8:303b).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new exchanges are extracted from the public file lPEPI264v.inf of the
ms-Windows driver. In this file, the sensor is named hv7131b but the exchanges
are those of the hv7131r.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- use an enum to define the sensor numbers
- use the sensor numbers to index the associated tables
- rename TAS5130CXX to TAS5130C
- rename HV7131C to HV7131R
- change some comments
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some webcams as ov511 may find many times an end of image.
In this case, with the last patch in image concatenation
(commit 799b1bd41f398054d46fd35f73abd01c4009f6ca),
the image pointer was NULL and the system crashed in memcpy().
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver exports a video device node per each camera interface/
video postprocessor (FIMC) device contained in Samsung S5P SoC series.
The driver is based on v4l2-mem2mem framework.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera requires the STREAM_NO_FID quirk. Add a corresponding entry
in the device IDs list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Corrupted video frames are dropped by default by the driver for
uncompressed formats. Data corruption is not less problematic for
compressed formats, so frame drop should be enabled by default for those
formats as well.
Mark buffers as faulty when an isochronous packet loss is detected for
any format, or when the buffer length doesn't match the image size for
uncompressed formats. Drop erroneous buffers regardless of whether the
format is compressed or uncompressed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a defintion for the "Print" button found on HP OEM
versions of the MCE remote. All of the other keys found on the HP OEM
version of the remote match the other keys as already defined.
Because, who doesn't need "remote printing", while one is sitting on the
couch across from one's PC? ;)
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add latest unported version of this driver to media/IR.
Next patch will port it to ir core.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This way it is possible to use evtest to create keymap for unknown remote.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
LIRC: add new IOCTL that enables learning mode (wide band receiver)
Still missing features: carrier report & timeout reports.
Will need to pack these into ir_raw_event
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some ir input devices have small buffer, and interrupt the host
each time it is full (or half full)
Add a helper that automaticly handles timeouts, and also
automaticly merges samples of same time (space-space)
Such samples might be placed by hardware because size of
sample in the buffer is small (a byte for example).
Also remove constness from ir_dev_props, because it now contains timeout
settings that driver might want to change
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, ir device registration fails if keymap requested by driver is not found.
Fix that by always compiling in the empty keymap, and using it as a failback.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds support for repeat detecting for NECX variant
Tested with uneversal remote
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Repeat space is 4 units, not 8.
Current code would never trigger a repeat.
However that isn't true for NECX, so repeat there
must be handled differently.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, jvc decoder will attempt misdetect next press as a repeat
of last keypress, therefore second keypress isn't detected.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is perfectly possible to have ir_raw_event_work
running concurently on two cpus, thus we must protect
it from that situation.
This stems from the fact that if hardware sends short packets of samples
we might end up queueing the work item more times that nessesary.
Such job isn't well suited for a workqueue, so use a kernel thread.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some handlers (lirc for example) allocates memory on initialization,
doing so in atomic context is cumbersome.
Fixes warning about sleeping function in atomic context.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* lirc: Don't propagate reset event to userspace
* lirc: Remove strange logic from lirc that would make first sample always be pulse
* Make TO_US macro actualy print what it should.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move IR drives below separate menu.
This allows to disable them.
Also correct a typo.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Moves drivers/staging/lirc/lirc_streamzap.c to
drivers/media/IR/streamzap.c, along with making the requisite Kconfig
and Makefile changes.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ports lirc_streamzap.c over to ir-core in-place, to be followed by
a patch moving the driver over to drivers/media/IR/streamzap.c and
enabling the proper Kconfig bits.
Presently, the in-kernel keymap doesn't work, as the stock Streamzap
remote uses an RC-5-like, but not-quite-RC-5 protocol, which the
in-kernel RC-5 decoder doesn't cope with. The remote can be used right
now with the lirc bridge driver though, and other remotes (at least an
RC-6(A) MCE remote) work perfectly with the driver.
I'll take a look at making the existing RC-5 decoder cope with this odd
duck, possibly implement another standalone decoder engine, or just
throw up my hands and say "meh, use lirc"... But the driver itself
should be perfectly sound.
Remaining items on the streamzap TODO list:
- add LIRC_SET_REC_TIMEOUT-alike support
- add LIRC_GET_M{AX,IN}_TIMEOUT-alike support
- add LIRC_GET_REC_RESOLUTION-alike support
All of the above should be trivial to add. There are patches pending to
add this support to ir-core from Maxim Levitsky, and I'll take care of
these once his patches get integrated. None of them are currently
essential though.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ir_input_dev gets filled in by __ir_input_register, the one
allocated in mceusb_init_input_dev was being overwritten by the correct
one shortly after it was initialized (ultimately resulting in a memory
leak). This bug was inherited from imon.c, and was pointed out to me by
Maxim Levitsky.
v2: fix incorrect dev arg to dev_dbg
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ir_input_dev gets filled in by __ir_input_register, the one
allocated in imon_init_idev was being overwritten by the correct one
shortly after it was initialized (ultimately resulting in a memory
leak). Additionally, there was an ill-advised memcpy into that
extraneous ir_input_dev which gets fixed by this.
Ill-advised memcpy pointed out by Dmitry Torokhov, bad usage of
ir_input_dev pointed out by Maxim Levitsky.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Per Dmitry Torokhov, following input_unregister_device with an
input_free_device is forbidden, the former is sufficient alone.
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CX23885 and CX25840 modules were using their own simple
IR pulse width measurement record type which required conversion
when passing to the new IR core. This change makes that record type
consistent with the new IR core and removes a data conversion.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of reporting an IR Rx timeout event as a ridiculously
long space, report it as a space of the lenght of the timeout.
This partially fixes operation with LIRC without breaking
interoperation with the in kernel decoders. The gaps lengths
reported to LIRC are still not real however.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Compute and report the maximum IR pulse measurment width, even
if we are set to perform carrier modulation or demodulation and
the number is fixed by the carrier freq.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver no longer depends on the old IR functions selected by
VIDEO_IR.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CX23885 IR controller was reported to cause an interrupt storm
on a TeVii S470 card, but was reported fine on an HVR-1250. Keep
integrated IR disabled by default on CX2388[57] based cards to avoid
a bad user experience in the general case.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Interrupts from the AV Core are best handled by a workqueue handler
since many I2C transactions are required to service the AV Core
interrupt. The AV_CORE PCI interrupt is disabled by the IRQ handler
and reenabled when the work handler is finished.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch encapsulates access to the PCI_INT_MSK register and
dev->pci_irqmask variable and protects them with a spinlock.
This is needed because both the hard IRQ handler and a workhandler
will need to manipulate the mask to disable the AV_CORE interrupt.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add initial IR Rx support using the intergrated IR controller in the
A/V core of the CX23885 bridge chip.
This initial support is flawed in that I2C transactions should not
be performed in a hard irq context. That will be fixed in a
follow on patch.
The TeVii S470 support is reported to generate perptual interrupts
that renders a user' system nearly unusable. The TeVii S470 IR
will be disabled by default in a follow on patch.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is primarily a port of the integrated IR controller code in
cx23885/cx23888-ir.c. Right now, only the CX2388[57] AV core will
really try to set up IR. This IR support, by design, still requires the
bridge driver to do final IO pin mux configuration and setup of the IR
controller parameters.
For the CX2388[578] chips, enabling the AV Core for IR also starts
sending Audio and Video interrupts to the bridge driver. For
CX2388[578] chips audio and video interrupts are ignored and
acknowledged when they happen.
IR interrupt handling and status logging is exluded for the CX23888
which does not have an IR controller on the AV core.
Note that experimentation reveals that the IR irq enables on the
CX23885 have an inverted logic sense. The CX23887 likely suffers from
the same quirk. For these chips, those irq enable bits are handled
as interrupt disables.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CX2584x and related cores are multifunction subdevices with a number
of internal blocks that act as interrupt sources. Move the v4L2_subdev
interrupt_service_routine callback from v4l_subdev_ir_ops to
v4l2_subdev_core_ops, as the video and audio blocks of a CX2584x and
related cores can generate interrupts along with the IR block. This
change also makes sense for other subdev's that generate interrupts and
do not have an IR block.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Explicitly configure the IR Tx and IR Rx pins to be driven by the
IR Rx and Tx pads from the AV core for CX23888 IR.
For the HVR-1850 and HVR-1290 configure the IR Tx level inversion,
so the Tx LED is off when idle.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a distinction on IR Tx for the CX2388[578] chips of carrier
sense inversion (space is a carrier burst and mark is no burst) and I/O
pin level inversion (0 is high output level, 1 is low output level).
Allow the caller to set these parameters distinctly as v4l2_subdevice
IR parameters. This permits the IR device to be configured and enabled
without the IR Tx LED being on during idle/space time due to an external
hardware level inversion
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add s_io_pin_config core subdev op for the CX2388[578] AV cores.
This is complete for IR_RX, IR_TX, GPIOs 16,19-23, and IRQ_N.
It likely needs work for the I2S signal direction.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a simple log_status function for raw analog video capture device nodes,
to provide insight into the state of the CX2388[578] A/V decoder core.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The offset in the eeprom data for the 79501 version of the HVR-1250 is at 0xc0
vs. the standard 0x80.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a small window between writing the cx25840 register
address over the i2c bus and reading the register contents back from the
cx25840 device that the i2c adapter lock was released. This change ensures the
adapter lock is not released until the register read is done.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Function i2c_wait_done() never returns negative values, so there is no
point in checking for them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't just check for nacks on zero-length transactions. Check on
other transactions too.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Documentation/i2c/fault-codes says that i2c adapter drivers should
return -ENXIO when no slave acks an address byte.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On laptops, the webcam sometimes disconnects when writing the first main
register (b300). This patch prevents the creation of a new /dev/video<n>
on streaming start.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The added controls are exposure, gain, autogain and backlight compensation.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPEG format did not work fine. The Bayer format offers correct VGA (640x480)
resolution, but bad QQVGA (160x120). This last resolution is removed.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bit 7 of the sensor gain register multiplies the 7bits value by two.
It is now always set with half the user gain value.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The start_1 exchange must be done by (reg, val) * 5 and not 8.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sensor enum definition was not at the right place.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2 implements two separate file operations for drivers that
use locked and unlocked ioctl callbacks. Since we want to remove
the ioctl file operation in favor of the unlocked variant, this
separation no longer seems helpful.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: John Kacur <jkacur@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (82 commits)
firewire: core: add forgotten dummy driver methods, remove unused ones
firewire: add isochronous multichannel reception
firewire: core: small clarifications in core-cdev
firewire: core: remove unused code
firewire: ohci: release channel in error path
firewire: ohci: use memory barriers to order descriptor updates
tools/firewire: nosy-dump: increment program version
tools/firewire: nosy-dump: remove unused code
tools/firewire: nosy-dump: use linux/firewire-constants.h
tools/firewire: nosy-dump: break up a deeply nested function
tools/firewire: nosy-dump: make some symbols static or const
tools/firewire: nosy-dump: change to kernel coding style
tools/firewire: nosy-dump: work around segfault in decode_fcp
tools/firewire: nosy-dump: fix it on x86-64
tools/firewire: add userspace front-end of nosy
firewire: nosy: note ioctls in ioctl-number.txt
firewire: nosy: use generic printk macros
firewire: nosy: endianess fixes and annotations
firewire: nosy: annotate __user pointers and __iomem pointers
firewire: nosy: fix device shutdown with active client
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (55 commits)
workqueue: mark init_workqueues() as early_initcall()
workqueue: explain for_each_*cwq_cpu() iterators
fscache: fix build on !CONFIG_SYSCTL
slow-work: kill it
gfs2: use workqueue instead of slow-work
drm: use workqueue instead of slow-work
cifs: use workqueue instead of slow-work
fscache: drop references to slow-work
fscache: convert operation to use workqueue instead of slow-work
fscache: convert object to use workqueue instead of slow-work
workqueue: fix how cpu number is stored in work->data
workqueue: fix mayday_mask handling on UP
workqueue: fix build problem on !CONFIG_SMP
workqueue: fix locking in retry path of maybe_create_worker()
async: use workqueue for worker pool
workqueue: remove WQ_SINGLE_CPU and use WQ_UNBOUND instead
workqueue: implement unbound workqueue
workqueue: prepare for WQ_UNBOUND implementation
libata: take advantage of cmwq and remove concurrency limitations
workqueue: fix worker management invocation without pending works
...
Fixed up conflicts in fs/cifs/* as per Tejun. Other trivial conflicts in
include/linux/workqueue.h, kernel/trace/Kconfig and kernel/workqueue.c
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
* 'v4l_for_2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (243 commits)
V4L/DVB: sms: Convert IR support to use the Remote Controller core
V4L/DVB: sms: properly initialize IR phys and IR name
V4L/DVB: standardize names at rc-dib0700 tables
V4L/DVB: smsusb: enable IR port for Hauppauge WinTV MiniStick
V4L/DVB: dib0700: Fix RC protocol logic to properly handle NEC/NECx and RC-5
V4L/DVB: dib0700: properly implement IR change_protocol
V4L/DVB: dib0700: break keytable into NEC and RC-5 variants
V4L/DVB: dib0700: avoid bad repeat
V4L/DVB: Port dib0700 to rc-core
V4L/DVB: Add a keymap file with dib0700 table
V4L/DVB: dvb-usb: add support for rc-core mode
V4L/DVB: dvb-usb: prepare drivers for using rc-core
V4L/DVB: dvb-usb: get rid of struct dvb_usb_rc_key
V4L/DVB: rj54n1cb0c: fix a comment in the driver
V4L/DVB: V4L2: sh_vou: VOU does support the full PAL resolution too
V4L/DVB: V4L2: sh_mobile_camera_ceu: add support for CSI2
V4L/DVB: V4L2: soc-camera: add a MIPI CSI-2 driver for SH-Mobile platforms
V4L/DVB: V4L2: soc-camera: export soc-camera bus type for notifications
V4L/DVB: V4L2: mediabus: add 12-bit Bayer and YUV420 pixel formats
V4L/DVB: mediabus: fix ambiguous pixel code names
...
Rewrites the siano IR implementation. The previous implementation were
non-standard. As such, it has issues if more than one device registers IR,
as there used to have some static constants used during protocol decoding
phase. Also, it used to implement its on RAW decoder, and only for RC5.
The new code uses RC core subsystem for handling IR. This brings several
new features to the driver, including:
- Allow to dynamically replace the IR keycodes;
- Supports all existing raw decoders (JVC, NEC, RC-5, RC-6, SONY);
- Supports lirc dev;
- Doesn't have race conditions when more than one sms IR is
registered;
- The code size for the IR implementation is very small;
- it exports the IR features via /sys/class/rc.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use a more standard way to name those tables, as they're currently used
by the script that coverts those tables to be loaded via userspace.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the proper gpio port for WinTV MiniStick, with the information provided
by Michael.
Thanks-to: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Simplifies the logic for handling firmware 1.20 RC messages, fixing the
logic.
While here, I tried to use a RC-6 remote controller from my TV set, but it
didn't work with dib0700. Not sure why, but maybe this never worked.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch implements change_protocol callback. With this change,
there's no need for an extra modprobe parameter to specify the
protocol. When a table is loaded (either from in-kernel rc-map
tables or via ir-keytable program), the driver will automatically
change the protocol, in order to work with the given table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having one big keytable with 2 protocols inside, break it
into two separate tables, being one for NEC and another for RC-5 variants,
and properly identify what variant should be used at the boards entries.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
a 250ms delay is too low for this device. It ends by producing false
repeat events. Increase the delay time to 500 ms to avoid troubles.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allows dvb-usb drivers to use rc-core, instead of the legacy
implementation.
No driver were ported yet to rc-core, so, some small adjustments
may be needed, when starting to migrate the drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a big patch, yet trivial. It just move the RC properties
to a separate struct, in order to prepare the dvb-usb drivers to
use rc-core. There's no change on the behavior of the drivers.
With this change, it is possible to have both legacy and rc-core
based code inside the dvb-usb-remote, allowing a gradual migration
to rc-core, driver per driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dvb-usb has its own IR handle code. Now that we have a Remote
Controller subsystem, we should start using it. So, remove this
struct, in favor of the similar struct defined at the RC subsystem.
This is a big, but trivial patch. It is a 3 line delect, plus
lots of rename on several dvb-usb files.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
RJ54N1CB0C is a Sharp camera sensor.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SH7724 datasheet specifies 480 pixels as the VOU maximum vertical resolution.
This is a bug in the datasheet, VOU also supports the full PAL resolution: 576
lines. Adjust the driver accordingly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using CEU with CSI2 on SH-Mobile requires some special configuration of the
former. We also have to switch from calling only one subdev .s_mbus_fmt and
.try_mbus_fmt to calling all subdevices. Take care to increment CSI2 driver
use count to prevent it from unloading, while in use.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some SH-Mobile SoCs implement a MIPI CSI-2 controller, that can interface to
several video clients and send data to the CEU or to the Image Signal
Processor. This patch implements a v4l2-subdevice driver for CSI-2 to be used
within the soc-camera framework, implementing the second subdevice in addition
to the actual video clients.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Endianness notation is meaningless for 8 bit YUYV codes. Switch pixel code
names to explicitly state the order of colour components in the data
stream.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds support for the KWorld PlusTV 340U and KWorld UB345-Q ATSC
sticks, which are really the same device. The sticks have an eMPIA
em2870 usb bridge chipset, an LG Electronics LGDT3304 ATSC/QAM
demodulator and an NXP TDA18271HD tuner -- early versions of the 340U
have a a TDA18271HD/C1, later models and the UB435-Q have a C2.
The stick has been tested succesfully with both VSB_8 and QAM_256 signals.
Its using lgdt3304 support added to the lgdt3305 driver by a prior patch,
rather than the current lgdt3304 driver, as its severely lacking in
functionality by comparison (see said patch for details).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In dvb_dvr_release, there is a test dvbdev->users==-1, but users are
never negative. This error results in hung tasks:
task PC stack pid father
bash D ffffffffa000c948 0 3264 3170 0x00000000
ffff88003aec5ce8 0000000000000086 0000000000011f80 0000000000011f80
ffff88003aec5fd8 ffff88003aec5fd8 ffff88003b848670 0000000000011f80
ffff88003aec5fd8 0000000000011f80 ffff88003e02a030 ffff88003b848670
Call Trace:
[<ffffffff813dd4a5>] dvb_dmxdev_release+0xc5/0x130
[<ffffffff8107b750>] ? autoremove_wake_function+0x0/0x40
[<ffffffffa00013a2>] dvb_usb_adapter_dvb_exit+0x42/0x70 [dvb_usb]
[<ffffffffa0000525>] dvb_usb_exit+0x55/0xd0 [dvb_usb]
[<ffffffffa00005ee>] dvb_usb_device_exit+0x4e/0x70 [dvb_usb]
[<ffffffffa000a065>] af9015_usb_device_exit+0x55/0x60 [dvb_usb_af9015]
[<ffffffff813a3f05>] usb_unbind_interface+0x55/0x1a0
[<ffffffff81316000>] __device_release_driver+0x70/0xe0
...
So check against 1 there instead.
BTW why's the TODO there? Adding TODOs to the code without
descriptions is like adding nothing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The UVC host and gadget drivers both define constants and structures in
private header files. Move all those definitions to linux/usb/video.h
where they can be shared by the two drivers (and be available for
userspace applications).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix comments. It is demodulator driver not DVB USB -bridge.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Firmware version is four digit long. Print all four digits instead of
three digits used earlier.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Function af9013_read_status() refactoring. Read lock bits in different
order to save count of register reads.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Program tuner before demodulator in case of channel set. Earlier it was
programmed during demodulator programming. This seems to resolve weird
error where demodulator misses sometimes ability to gain lock.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID 07ca:815a for AverMedia AVerTV Volar M (A815Mac).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The first VC0321 settings were done at webcam connection only. They must also
be done on resume after suspend.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bit 0x04 of the bridge register 02 (GPIO) is used for audio connection
in webcams containing the bridge SN9C105. This patch sets it correctly,
according to the presence of an audio device.
Tested-by: Kyle Baker <kyleabaker@gmail.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When there is an audio device, use a lower alternate setting.
This patch does not fix correctly all audio and bandwidth problems.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function has sanity checks to make sure that "dev" is non-null. I
moved the dereference down below the checks. In the current code "dev"
is never actually null.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a typo here. We meant to test "rbuf" instead of "drv". We
already tested "drv" earlier.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s/ENODEV/ENOMEM, per Andreas.
This fix got lost when someone merged "dib3000mc: reduce large stack
usage". Please don't lose fixes.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stanse found that in ivtvfb_callback_cleanup and ivtvfb_callback_init
there are unneeded tests for itv being NULL. But itv is initialized
as container_of with non-zero offset in those functions, so it is
never NULL (even if v4l2_dev is). This was found because itv is
dereferenced earlier than the test.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The lirc userspace needs all the current ioctls defined, and we need to
put the header files in places out-of-tree and/or staging lirc drivers
(which I plan to prep soon) can easily build with. I've actually tested this
in a tree w/all the lirc drivers queued up to be submitted for staging. I'm
also reasonably sure that Andy Walls is going to need most of the ioctls
anyway for his cx23888 IR driver work.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
CONFIG_FB_OMAP2_FORCE_AUTO_UPDATE doesn't exist in Kconfig and is never defined anywhere
else, therefore removing all references for it from the source code.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes possible race conditions in queue management with SMP:
when a frame was completed, the irq function tried to use the next frame
buffer. At this time, it was possible that the application on an other
processor updated the frame pointer, making the image to point to a bad
buffer.
The patch contains two main changes:
- the image transfer uses the queue indexes which are protected against
simultaneous memory access,
- the image pointer which is used for image concatenation is only set at
interrupt level.
Some subdrivers which used the image pointer have been updated.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The problem may occur with SMP:
- a frame is completed at interrupt level (in gspca_frame_add with
packet_type == LAST_PACKET,
- just after clearing the bit V4L2_BUF_FLAG_QUEUED and before setting
the bit V4L2_BUF_FLAG_DONE, on the other processor, the application
tries to requeue the same frame buffer,
- then, the qbuf function succeeds because ALL_FLAGS are not set.
The fix sets and resets the two flags in one instruction.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As pointed by Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>,
The config Option DVB_DIBCOM_DEBUG was dropped while removing the dibusb
driver in favor of dvb-usb in 2005. However it remaind existant at some
places of the kernel config.
Instead of just removing the debug capability, the better is to just remove
the bad dependency, making the modprobe function always visible.
Thanks-to: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The recently added support for lgs8g75 included some 8051 machine code
without accompanying source code. Replace this with use of the
firmware loader.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch to the si470x_vidioc_s_tuner function was developed in
cooperation with Roel Kluin <roel.kluin@gmail.com>. It sets the default
retval to 0 instead of -EINVAL, identical to what is done in all other
set/get functions of v4l2_ioctl_ops. This is just as cosmetic change, as
retval is directly overwritten by the si470x_disconnect_check() anyway.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Spent a while last night getting device initialization packet captures
under Windows for all generations of devices. There are a few places
where we were doing things differently, and few things we were doing
that we don't need to do, particularly on gen3 hardware, and I *think*
one of those things is what was locking up my pinnacle hw from time to
time -- at least, its been perfectly well behaved every time its been
plugged in since making this change.
First up, we're adding a bit more to the gen1 init routine here. Its
not absolutely necessary, the hardware works the same both with and
without it, but I'd like to be consistent w/Windows here.
Second, DEVICE_RESET is never called when initializing either of my
gen3 devices, its only called for gen1 and gen2. The bits in the gen3
init after removing that, are safe (and interesting) to run on all
hardware, so there's no more gen3-specific init done, there's instead
a generic mceusb_get_parameters() that is run for all hardware.
Third, the gen3 flag isn't needed. We only care if hardware is gen3
during probe, so I've dropped that from the device flags struct.
Successfully tested on all three generations of mceusb hardware.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prior init unification/simplification patch made these unused, forgot
to remove them, so this silences:
drivers/media/IR/mceusb.c: In function ‘mceusb_gen1_init’:
drivers/media/IR/mceusb.c:769: warning: unused variable ‘partial’
drivers/media/IR/mceusb.c:768: warning: unused variable ‘i’
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New code should not rely on the big kernel lock,
so use the unlocked_ioctl file operation in lirc.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ir-jvc-decoder uses bitreverse interfaces, so it should select
BITREVERSE.
ir-jvc-decoder.c:(.text+0x550bc): undefined reference to `byte_rev_table'
ir-jvc-decoder.c:(.text+0x550c6): undefined reference to `byte_rev_table'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Wed, Jul 07, 2010 at 02:52:58PM +0200, Jiri Slaby wrote:
> Hi,
>
> stanse found a locking error in lirc_dev_fop_read:
> if (mutex_lock_interruptible(&ir->irctl_lock))
> return -ERESTARTSYS;
> ...
> while (written < length && ret == 0) {
> if (mutex_lock_interruptible(&ir->irctl_lock)) { #1
> ret = -ERESTARTSYS;
> break;
> }
> ...
> }
>
> remove_wait_queue(&ir->buf->wait_poll, &wait);
> set_current_state(TASK_RUNNING);
> mutex_unlock(&ir->irctl_lock); #2
>
> If lock at #1 fails, it beaks out of the loop, with the lock unlocked,
> but there is another "unlock" at #2.
This should do the trick. Completely untested beyond compiling, but its
not exactly a complicated fix, and in practice, I'm not aware of anyone
ever actually tripping that locking bug, so there's zero functional change
in typical use here.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since commit b402843787
the 'driver_data' field resides in device's struct device_private
which may be allocated by dev_set_drvdata() if device_private
struct was not allocated previously.
dev_set_drvdata() is used in video_set_drvdata() to set
the driver's private data pointer in v4l2 drivers. Setting
the private data _before_ registering the v4l2 device results
in a memory leak since __video_register_device() also calls
video_set_drvdata(), but after zeroing the device structure.
Thus, the reference to the previously allocated device_private
struct goes lost and a new device_private will be allocated.
All v4l drivers which call video_set_drvdata() _before_
calling video_register_device() are affected. The patch fixes
__video_register_device() to preserve previously allocated
device_private reference.
Caught by kmemleak.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the register CLUNC to reset the CPTU registers (LSB & MSB) when they
saturate at 0xFFFF. Fixes as well a few register typos.
Signed-off-by: Guillaume Audirac <guillaume.audirac@webag.fr>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a missing bit for reading the transmission mode (2K/8K) in
tda10048_get_tps
Signed-off-by: Guillaume Audirac <guillaume.audirac@webag.fr>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Completes the bit-error-rate read function with the CBER register (before
Viterbi decoder). The returned value is 1e8*actual_ber to be positive.
Also includes some typo mistakes.
Signed-off-by: Guillaume Audirac <guillaume.audirac@webag.fr>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Started out as an effort to try to tackle the last remaining issue I'm
having with this damned pinnacle device getting wedged the first time
its plugged in after an indeterminate length of not being plugged in.
Didn't get that solved yet, but did streamline the init code a bit more
and remove some superfluous gunk. Nukes a completely unneeded call to
usb_device_init() and several lines of overly complex crap in the gen1
device init path.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dan Carpenter