The problem that this patch aims to fix is vfsmount refcounting scalability.
We need to take a reference on the vfsmount for every successful path lookup,
which often go to the same mount point.
The fundamental difficulty is that a "simple" reference count can never be made
scalable, because any time a reference is dropped, we must check whether that
was the last reference. To do that requires communication with all other CPUs
that may have taken a reference count.
We can make refcounts more scalable in a couple of ways, involving keeping
distributed counters, and checking for the global-zero condition less
frequently.
- check the global sum once every interval (this will delay zero detection
for some interval, so it's probably a showstopper for vfsmounts).
- keep a local count and only taking the global sum when local reaches 0 (this
is difficult for vfsmounts, because we can't hold preempt off for the life of
a reference, so a counter would need to be per-thread or tied strongly to a
particular CPU which requires more locking).
- keep a local difference of increments and decrements, which allows us to sum
the total difference and hence find the refcount when summing all CPUs. Then,
keep a single integer "long" refcount for slow and long lasting references,
and only take the global sum of local counters when the long refcount is 0.
This last scheme is what I implemented here. Attached mounts and process root
and working directory references are "long" references, and everything else is
a short reference.
This allows scalable vfsmount references during path walking over mounted
subtrees and unattached (lazy umounted) mounts with processes still running
in them.
This results in one fewer atomic op in the fastpath: mntget is now just a
per-CPU inc, rather than an atomic inc; and mntput just requires a spinlock
and non-atomic decrement in the common case. However code is otherwise bigger
and heavier, so single threaded performance is basically a wash.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Suggested by Andreas, mnt_ prefix is clearer namespace, follows kernel
conventions better, and is easier for tab complete. I introduced these
names so I'll admit they were not good choices.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Rather than keep a d_mounted count in the dentry, set a dentry flag instead.
The flag can be cleared by checking the hash table to see if there are any
mounts left, which is not time critical because it is performed at detach time.
The mounted state of a dentry is only used to speculatively take a look in the
mount hash table if it is set -- before following the mount, vfsmount lock is
taken and mount re-checked without races.
This saves 4 bytes on 32-bit, nothing on 64-bit but it does provide a hole I
might use later (and some configs have larger than 32-bit spinlocks which might
make use of the hole).
Autofs4 conversion and changelog by Ian Kent <raven@themaw.net>:
In autofs4, when expring direct (or offset) mounts we need to ensure that we
block user path walks into the autofs mount, which is covered by another mount.
To do this we clear the mounted status so that follows stop before walking into
the mount and are essentially blocked until the expire is completed. The
automount daemon still finds the correct dentry for the umount due to the
follow mount logic in fs/autofs4/root.c:autofs4_follow_link(), which is set as
an inode operation for direct and offset mounts only and is called following
the lookup that stopped at the covered mount.
At the end of the expire the covering mount probably has gone away so the
mounted status need not be restored. But we need to check this and only restore
the mounted status if the expire failed.
XXX: autofs may not work right if we have other mounts go over the top of it?
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If clone_mnt() happens while mnt_make_readonly() is running, the
cloned mount might have MNT_WRITE_HOLD flag set, which results in
mnt_want_write() spinning forever on this mount.
Needs CAP_SYS_ADMIN to trigger deliberately and unlikely to happen
accidentally. But if it does happen it can hang the machine.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
After pushing down the BKL to the get_sb/fill_super operations of the
filesystems that still make usage of the BKL it is safe to remove it from
do_new_mount().
I've read through all the code formerly covered by the BKL inside
do_kern_mount() and have satisfied myself that it doesn't need the BKL
any more.
Signed-off-by: Jan Blunck <jblunck@infradead.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Sanity check the flags passed to change_mnt_propagation(). Exactly
one flag should be set. Return EINVAL otherwise.
Userspace can pass in arbitrary combinations of MS_* flags to mount().
do_change_type() is called if any of MS_SHARED, MS_PRIVATE, MS_SLAVE,
or MS_UNBINDABLE is set. do_change_type() clears MS_REC and then
calls change_mnt_propagation() with the rest of the user-supplied
flags. change_mnt_propagation() clearly assumes only one flag is set
but do_change_type() does not check that this is true. For example,
mount() with flags MS_SHARED | MS_RDONLY does not actually make the
mount shared or read-only but does clear MNT_UNBINDABLE.
Signed-off-by: Valerie Aurora <vaurora@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fs: brlock vfsmount_lock
Use a brlock for the vfsmount lock. It must be taken for write whenever
modifying the mount hash or associated fields, and may be taken for read when
performing mount hash lookups.
A new lock is added for the mnt-id allocator, so it doesn't need to take
the heavy vfsmount write-lock.
The number of atomics should remain the same for fastpath rlock cases, though
code would be slightly slower due to per-cpu access. Scalability is not not be
much improved in common cases yet, due to other locks (ie. dcache_lock) getting
in the way. However path lookups crossing mountpoints should be one case where
scalability is improved (currently requiring the global lock).
The slowpath is slower due to use of brlock. On a 64 core, 64 socket, 32 node
Altix system (high latency to remote nodes), a simple umount microbenchmark
(mount --bind mnt mnt2 ; umount mnt2 loop 1000 times), before this patch it
took 6.8s, afterwards took 7.1s, about 5% slower.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit d0adde574b added MNT_STRICTATIME
but it isn't actually used (MS_STRICTATIME clears MNT_RELATIME and
MNT_NOATIME rather than setting any mount flag).
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add three helpers that retrieve a refcounted copy of the root and cwd
from the supplied fs_struct.
get_fs_root()
get_fs_pwd()
get_fs_root_and_pwd()
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://git.infradead.org/users/eparis/notify: (132 commits)
fanotify: use both marks when possible
fsnotify: pass both the vfsmount mark and inode mark
fsnotify: walk the inode and vfsmount lists simultaneously
fsnotify: rework ignored mark flushing
fsnotify: remove global fsnotify groups lists
fsnotify: remove group->mask
fsnotify: remove the global masks
fsnotify: cleanup should_send_event
fanotify: use the mark in handler functions
audit: use the mark in handler functions
dnotify: use the mark in handler functions
inotify: use the mark in handler functions
fsnotify: send fsnotify_mark to groups in event handling functions
fsnotify: Exchange list heads instead of moving elements
fsnotify: srcu to protect read side of inode and vfsmount locks
fsnotify: use an explicit flag to indicate fsnotify_destroy_mark has been called
fsnotify: use _rcu functions for mark list traversal
fsnotify: place marks on object in order of group memory address
vfs/fsnotify: fsnotify_close can delay the final work in fput
fsnotify: store struct file not struct path
...
Fix up trivial delete/modify conflict in fs/notify/inotify/inotify.c.
If sget() finds a matching superblock being set up, it'll
grab an active reference to it and grab s_umount. That's
fine - we'll wait for completion of foofs_get_sb() that way.
However, if said foofs_get_sb() fails we'll end up holding
the halfway-created superblock. deactivate_locked_super()
called by foofs_get_sb() will just unlock the sucker since
we are holding another active reference to it.
What we need is a way to tell if superblock has been successfully
set up. Unfortunately, neither ->s_root nor the check for
MS_ACTIVE quite fit. Cheap and easy way, suitable for backport:
new flag set by the (only) caller of ->get_sb(). If that flag
isn't present by the time sget() grabbed s_umount on preexisting
superblock it has found, it's seeing a stillborn and should
just bury it with deactivate_locked_super() (and repeat the search).
Longer term we want to set that flag in ->get_sb() instances (and
check for it to distinguish between "sget() found us a live sb"
and "sget() has allocated an sb, we need to set it up" in there,
instead of checking ->s_root as we do now).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org
Per-mount watches allow groups to listen to fsnotify events on an entire
mount. This patch simply adds and initializes the fields needed in the
vfsmount struct to make this happen.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Eric Paris <eparis@redhat.com>
This patch adds the list and mask fields needed to support vfsmount marks.
These are the same fields fsnotify needs on an inode. They are not used,
just declared and we note where the cleanup hook should be (the function is
not yet defined)
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Eric Paris <eparis@redhat.com>
1) i_flags simply doesn't work for mount/unlink race prevention;
we may have many links to file and rm on one of those obviously
shouldn't prevent bind on top of another later on. To fix it
right way we need to mark _dentry_ as unsuitable for mounting
upon; new flag (DCACHE_CANT_MOUNT) is protected by d_flags and
i_mutex on the inode in question. Set it (with dont_mount(dentry))
in unlink/rmdir/etc., check (with cant_mount(dentry)) in places
in namespace.c that used to check for S_DEAD. Setting S_DEAD
is still needed in places where we used to set it (for directories
getting killed), since we rely on it for readdir/rmdir race
prevention.
2) rename()/mount() protection has another bogosity - we unhash
the target before we'd checked that it's not a mountpoint. Fixed.
3) ancient bogosity in pivot_root() - we locked i_mutex on the
right directory, but checked S_DEAD on the different (and wrong)
one. Noticed and fixed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add a new UMOUNT_NOFOLLOW flag to umount(2). This is needed to prevent
symlink attacks in unprivileged unmounts (fuse, samba, ncpfs).
Additionally, return -EINVAL if an unknown flag is used (and specify
an explicitly unused flag: UMOUNT_UNUSED). This makes it possible for
the caller to determine if a flag is supported or not.
CC: Eugene Teo <eugene@redhat.com>
CC: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
It hadn't been needed since we'd sanitized the logics in
mark_mounts_for_expiry() (which, in turn, used to be a
rudiment of bad old times when namespace_sem was per-ns).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The handling of mount flags in set_mnt_shared() got a little tangled
up during previous cleanups, with the following problems:
* MNT_PNODE_MASK is defined as a literal constant when it should be a
bitwise xor of other MNT_* flags
* set_mnt_shared() clears and then sets MNT_SHARED (part of MNT_PNODE_MASK)
* MNT_PNODE_MASK could use a comment in mount.h
* MNT_PNODE_MASK is a terrible name, change to MNT_SHARED_MASK
This patch fixes these problems.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
First of all, get_source() never results in CL_PROPAGATION
alone. We either get CL_MAKE_SHARED (for the continuation
of peer group) or CL_SLAVE (slave that is not shared) or both
(beginning of peer group among slaves). Massage the code to
make that explicit, kill CL_PROPAGATION test in clone_mnt()
(nothing sets CL_MAKE_SHARED without CL_PROPAGATION and in
clone_mnt() we are checking CL_PROPAGATION after we'd found
that there's no CL_SLAVE, so the check for CL_MAKE_SHARED
would do just as well).
Fix comments, while we are at it...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
MNT_WRITE_HOLD shouldn't leak into new vfsmount and neither
should MNT_SHARED (the latter will be set properly, along with
the rest of shared-subtree data structures)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This reverts commit e9496ff46a. Quoth Al:
"it's dependent on a lot of other stuff not currently in mainline
and badly broken with current fs/namespace.c. Sorry, badly
out-of-order cherry-pick from old queue.
PS: there's a large pending series reworking the refcounting and
lifetime rules for vfsmounts that will, among other things, allow to
rip a subtree away _without_ dissolving connections in it, to be
garbage-collected when all active references are gone. It's
considerably saner wrt "is the subtree busy" logics, but it's nowhere
near being ready for merge at the moment; this changeset is one of the
things becoming possible with that sucker, but it certainly shouldn't
have been picked during this cycle. My apologies..."
Noticed-by: Eric Paris <eparis@redhat.com>
Requested-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch allows LSM modules to determine based on original mount flags
passed to mount(). A LSM module can get masked mount flags (if needed) by
flags &= ~(MS_NOSUID | MS_NOEXEC | MS_NODEV | MS_ACTIVE |
MS_NOATIME | MS_NODIRATIME | MS_RELATIME| MS_KERNMOUNT |
MS_STRICTATIME);
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <jmorris@namei.org>
sys_mount() reads/copies a whole page for its "type" parameter. When
do_mount_root() passes a kernel address that points to an object which is
smaller than a whole page, copy_mount_options() will happily go past this
memory object, possibly dereferencing "wild" pointers that could be in any
state (hence the kmemcheck warning, which shows that parts of the next
page are not even allocated).
(The likelihood of something going wrong here is pretty low -- first of
all this only applies to kernel calls to sys_mount(), which are mostly
found in the boot code. Secondly, I guess if the page was not mapped,
exact_copy_from_user() _would_ in fact handle it correctly because of its
access_ok(), etc. checks.)
But it is much nicer to avoid the dubious reads altogether, by stopping as
soon as we find a NUL byte. Is there a good reason why we can't do
something like this, using the already existing strndup_from_user()?
[akpm@linux-foundation.org: make copy_mount_string() static]
[AV: fix compat mount breakage, which involves undoing akpm's change above]
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: al <al@dizzy.pdmi.ras.ru>
I suspect that mnt_want_write_file() may have wrong assumption. I think
mnt_want_write_file() is assuming it increments ->mnt_writers if
(file->f_mode & FMODE_WRITE). But, if it's special_file(), it is false?
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix various silly problems wrt mnt_namespace.h:
- exit_mnt_ns() isn't used, remove it
- done that, sched.h and nsproxy.h inclusions aren't needed
- mount.h inclusion was need for vfsmount_lock, but no longer
- remove mnt_namespace.h inclusion from files which don't use anything
from mnt_namespace.h
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The purpose of this patch is to improve the remote mount path lookup
support for distributed filesystems such as the NFSv4 client.
When given a mount command of the form "mount server:/foo/bar /mnt", the
NFSv4 client is required to look up the filehandle for "server:/", and
then look up each component of the remote mount path "foo/bar" in order
to find the directory that is actually going to be mounted on /mnt.
Following that remote mount path may involve following symlinks,
crossing server-side mount points and even following referrals to
filesystem volumes on other servers.
Since the standard VFS path lookup code already supports walking paths
that contain all these features (using in-kernel automounts for
following referrals) we would like to be able to reuse that rather than
duplicate the full path traversal functionality in the NFSv4 client code.
This patch therefore defines a VFS helper function create_mnt_ns(), that
sets up a temporary filesystem namespace and attaches a root filesystem to
it. It exports the create_mnt_ns() and put_mnt_ns() function for use by
filesystem modules.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to allow modules to use it without having to export vfsmount_lock.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
d_unlinked() will be used in middle-term to ban checkpointing when opened
but unlinked file is detected, and in long term, to detect such situation
and special case on it.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch speeds up lmbench lat_mmap test by about another 2% after the
first patch.
Before:
avg = 462.286
std = 5.46106
After:
avg = 453.12
std = 9.58257
(50 runs of each, stddev gives a reasonable confidence)
It does this by introducing mnt_clone_write, which avoids some heavyweight
operations of mnt_want_write if called on a vfsmount which we know already
has a write count; and mnt_want_write_file, which can call mnt_clone_write
if the file is open for write.
After these two patches, mnt_want_write and mnt_drop_write go from 7% on
the profile down to 1.3% (including mnt_clone_write).
[AV: mnt_want_write_file() should take file alone and derive mnt from it;
not only all callers have that form, but that's the only mnt about which
we know that it's already held for write if file is opened for write]
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch speeds up lmbench lat_mmap test by about 8%. lat_mmap is set up
basically to mmap a 64MB file on tmpfs, fault in its pages, then unmap it.
A microbenchmark yes, but it exercises some important paths in the mm.
Before:
avg = 501.9
std = 14.7773
After:
avg = 462.286
std = 5.46106
(50 runs of each, stddev gives a reasonable confidence, but there is quite
a bit of variation there still)
It does this by removing the complex per-cpu locking and counter-cache and
replaces it with a percpu counter in struct vfsmount. This makes the code
much simpler, and avoids spinlocks (although the msync is still pretty
costly, unfortunately). It results in about 900 bytes smaller code too. It
does increase the size of a vfsmount, however.
It should also give a speedup on large systems if CPUs are frequently operating
on different mounts (because the existing scheme has to operate on an atomic in
the struct vfsmount when switching between mounts). But I'm most interested in
the single threaded path performance for the moment.
[AV: minor cleanup]
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
These guys are what we add as submounts; checks for "is that attached in
our namespace" are simply irrelevant for those and counterproductive for
use of private vfsmount trees a-la what NFS folks want.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Put generic_show_options read access to s_options under rcu_read_lock,
split save_mount_options() into "we are setting it the first time"
(uses in foo_fill_super()) and "we are relacing and freeing the old one",
synchronize_rcu() before kfree() in the latter.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We shouldn't just touch the namespace of current process
Caught-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Since commit 0a1c01c947 ("Make relatime
default") when a file system is mounted explicitely with noatime it gets
both the MNT_RELATIME and MNT_NOATIME bits set.
This shows up like this in /proc/mounts:
/dev/xxx /yyy ext3 rw,noatime,relatime,errors=continue,data=writeback 0 0
That looks strange. The VFS uses noatime in this case, but both flags
are set. So it's more a cosmetic issue, but still better to fix.
Cc: mjg@redhat.com
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't pull it in sched.h; very few files actually need it and those
can include directly. sched.h itself only needs forward declaration
of struct fs_struct;
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pure code move; two new helper functions for nfsd and daemonize
(unshare_fs_struct() and daemonize_fs_struct() resp.; for now -
the same code as used to be in callers). unshare_fs_struct()
exported (for nfsd, as copy_fs_struct()/exit_fs() used to be),
copy_fs_struct() and exit_fs() don't need exports anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Not because execve races with _that_ are serious - we really
need a situation when final drop of fs_struct refcount is
done by something that used to have it as current->fs.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
simple_set_mnt() is defined as returning 'int' but always returns 0.
Callers assume simple_set_mnt() never fails and don't properly cleanup if
it were to _ever_ fail. For instance, get_sb_single() and get_sb_nodev()
should:
up_write(sb->s_unmount);
deactivate_super(sb);
if simple_set_mnt() fails.
Since simple_set_mnt() never fails, would be cleaner if it did not
return anything.
[akpm@linux-foundation.org: fix build]
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Change the default behaviour of the kernel to use relatime for all
filesystems. This can be overridden with the "strictatime" mount
option.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for explicitly requesting full atime updates. This makes it
possible for kernels to default to relatime but still allow userspace to
override it.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Getting this wrong caused
WARNING: at fs/namespace.c:636 mntput_no_expire+0xac/0xf2()
due to optimistically checking cpu_writer->mnt outside the spinlock.
Here's what we really want:
* we know that nobody will set cpu_writer->mnt to mnt from now on
* all changes to that sucker are done under cpu_writer->lock
* we want the laziest equivalent of
spin_lock(&cpu_writer->lock);
if (likely(cpu_writer->mnt != mnt)) {
spin_unlock(&cpu_writer->lock);
continue;
}
/* do stuff */
that would make sure we won't miss earlier setting of ->mnt done by
another CPU.
Anyway, for now we just move the spin_lock() earlier and move the test
into the properly locked region.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reported-and-tested-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The extra semicolon serves no purpose.
Signed-off-by: Julia Lawall <julia@diku.dk>
Reviewed-by: Richard Genoud <richard.genoud@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Conflicts:
security/keys/internal.h
security/keys/process_keys.c
security/keys/request_key.c
Fixed conflicts above by using the non 'tsk' versions.
Signed-off-by: James Morris <jmorris@namei.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: James Morris <jmorris@namei.org>
In the last refactoring of shrink_submounts a variable was not completely
renamed. So finish the renaming of mnt to m now.
Without this if you attempt to mount an nfs mount that has both automatic
nfs sub mounts on it, and has normal mounts on it. The unmount will
succeed when it should not.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daemons that need to be launched while the rootfs is read-only can now
poll /proc/mounts to be notified when their O_RDWR requests may no
longer end in EROFS.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* do not pass nameidata; struct path is all the callers want.
* switch to new helpers:
user_path_at(dfd, pathname, flags, &path)
user_path(pathname, &path)
user_lpath(pathname, &path)
user_path_dir(pathname, &path) (fail if not a directory)
The last 3 are trivial macro wrappers for the first one.
* remove nameidata in callers.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
- use kstrdup() instead of kmalloc() + memcpy()
- return NULL if allocating ->mnt_devname failed
- mnt_devname should be const
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use WARN() instead of a printk+WARN_ON() pair; this way the message
becomes part of the warning section for better reporting/collection.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch causes SELinux mount options to show up in /proc/mounts. As
with other code in the area seq_put errors are ignored. Other LSM's
will not have their mount options displayed until they fill in their own
security_sb_show_options() function.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: James Morris <jmorris@namei.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove lives_below_in_same_fs() since is_subdir() from fs/dcache.c is
providing the same functionality.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Acked-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We don't need to turn quotas off before remounting root ro, because
do_remount_sb() already handles this.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Show peer group ID of nearest dominating group that has intersection
with the mount's namespace.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[mszeredi@suse.cz] rewrite and split big patch into managable chunks
/proc/mounts in its current form lacks important information:
- propagation state
- root of mount for bind mounts
- the st_dev value used within the filesystem
- identifier for each mount and it's parent
It also suffers from the following problems:
- not easily extendable
- ambiguity of mountpoints within a chrooted environment
- doesn't distinguish between filesystem dependent and independent options
- doesn't distinguish between per mount and per super block options
This patch introduces /proc/<pid>/mountinfo which attempts to address
all these deficiencies.
Code shared between /proc/<pid>/mounts and /proc/<pid>/mountinfo is
extracted into separate functions.
Thanks to Al Viro for the help in getting the design right.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Allow /proc/<pid>/mountinfo to use the root of <pid> to calculate
mountpoints.
- move definition of 'struct proc_mounts' to <linux/mnt_namespace.h>
- add the process's namespace and root to this structure
- pass a pointer to 'struct proc_mounts' into seq_operations
In addition the following cleanups are made:
- use a common open function for /proc/<pid>/{mounts,mountstat}
- surround namespace.c part of these proc files with #ifdef CONFIG_PROC_FS
- make the seq_operations structures const
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add a unique ID to each peer group using the IDR infrastructure. The
identifiers are reused after the peer group dissolves.
The IDR structures are protected by holding namepspace_sem for write
while allocating or deallocating IDs.
IDs are allocated when a previously unshared vfsmount becomes the
first member of a peer group. When a new member is added to an
existing group, the ID is copied from one of the old members.
IDs are freed when the last member of a peer group is unshared.
Setting the MNT_SHARED flag on members of a subtree is done as a
separate step, after all the IDs have been allocated. This way an
allocation failure can be cleaned up easilty, without affecting the
propagation state.
Based on design sketch by Al Viro.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add a unique ID to each vfsmount using the IDR infrastructure. The
identifiers are reused after the vfsmount is freed.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Further reduction of stack footprint (sys_pivot_root());
lose useless BKL in there, while we are at it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Taking namespace_sem shared there isn't worth the trouble, especially with
vfsmount ID allocation about to be added. That way we know that umount_tree(),
copy_tree() and clone_mnt() are _always_ serialized by namespace_sem.
umount_tree() still needs vfsmount_lock (it manipulates hash chains, among
other things), but that's a separate story.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Originally from: Herbert Poetzl <herbert@13thfloor.at>
This is the core of the read-only bind mount patch set.
Note that this does _not_ add a "ro" option directly to the bind mount
operation. If you require such a mount, you must first do the bind, then
follow it up with a 'mount -o remount,ro' operation:
If you wish to have a r/o bind mount of /foo on bar:
mount --bind /foo /bar
mount -o remount,ro /bar
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This is the real meat of the entire series. It actually
implements the tracking of the number of writers to a mount.
However, it causes scalability problems because there can be
hundreds of cpus doing open()/close() on files on the same mnt at
the same time. Even an atomic_t in the mnt has massive scalaing
problems because the cacheline gets so terribly contended.
This uses a statically-allocated percpu variable. All want/drop
operations are local to a cpu as long that cpu operates on the same
mount, and there are no writer count imbalances. Writer count
imbalances happen when a write is taken on one cpu, and released
on another, like when an open/close pair is performed on two
Upon a remount,ro request, all of the data from the percpu
variables is collected (expensive, but very rare) and we determine
if there are any outstanding writers to the mount.
I've written a little benchmark to sit in a loop for a couple of
seconds in several cpus in parallel doing open/write/close loops.
http://sr71.net/~dave/linux/openbench.c
The code in here is a a worst-possible case for this patch. It
does opens on a _pair_ of files in two different mounts in parallel.
This should cause my code to lose its "operate on the same mount"
optimization completely. This worst-case scenario causes a 3%
degredation in the benchmark.
I could probably get rid of even this 3%, but it would be more
complex than what I have here, and I think this is getting into
acceptable territory. In practice, I expect writing more than 3
bytes to a file, as well as disk I/O to mask any effects that this
has.
(To get rid of that 3%, we could have an #defined number of mounts
in the percpu variable. So, instead of a CPU getting operate only
on percpu data when it accesses only one mount, it could stay on
percpu data when it only accesses N or fewer mounts.)
[AV] merged fix for __clear_mnt_mount() stepping on freed vfsmount
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch adds two function mnt_want_write() and mnt_drop_write(). These are
used like a lock pair around and fs operations that might cause a write to the
filesystem.
Before these can become useful, we must first cover each place in the VFS
where writes are performed with a want/drop pair. When that is complete, we
can actually introduce code that will safely check the counts before allowing
r/w<->r/o transitions to occur.
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
... and take it out of ->umount_begin() instances. Call with all locks
already taken (by do_umount()) and leave calling release_mounts() to
caller (it will do release_mounts() anyway, so we can just put into
the same list).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
make propagate_mount_busy() exclude references from the vfsmounts
that had been isolated by umount_tree() and are just waiting for
release_mounts() to dispose of their ->mnt_parent/->mnt_mountpoint.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
seq_path() is always called with a dentry and a vfsmount from a struct path.
Make seq_path() take it directly as an argument.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In nearly all cases the set_fs_{root,pwd}() calls work on a struct
path. Change the function to reflect this and use path_get() here.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Use struct path in fs_struct.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Add path_put() functions for releasing a reference to the dentry and
vfsmount of a struct path in the right order
* Switch from path_release(nd) to path_put(&nd->path)
* Rename dput_path() to path_put_conditional()
[akpm@linux-foundation.org: fix cifs]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: <linux-fsdevel@vger.kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the central patch of a cleanup series. In most cases there is no good
reason why someone would want to use a dentry for itself. This series reflects
that fact and embeds a struct path into nameidata.
Together with the other patches of this series
- it enforced the correct order of getting/releasing the reference count on
<dentry,vfsmount> pairs
- it prepares the VFS for stacking support since it is essential to have a
struct path in every place where the stack can be traversed
- it reduces the overall code size:
without patch series:
text data bss dec hex filename
5321639 858418 715768 6895825 6938d1 vmlinux
with patch series:
text data bss dec hex filename
5320026 858418 715768 6894212 693284 vmlinux
This patch:
Switch from nd->{dentry,mnt} to nd->path.{dentry,mnt} everywhere.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix cifs]
[akpm@linux-foundation.org: fix smack]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
path_release_on_umount() should only be called from sys_umount(). I merged the
function into sys_umount() instead of having in in namei.c.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
do_mount() uses a whopping 616 bytes of stack on x86_64 in 2.6.24-mm1,
largely thanks to gcc inlining the various helper functions.
noinlining these can slim it down a lot; on my box this patch gets it down
to 168, which is mostly the struct nameidata nd; left on the stack.
These functions are called only as do_mount() helpers; none of them should
be in any path that would see a performance benefit from inlining...
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new s_options field to struct super_block. Filesystems can save
mount options passed to them in mount or remount. It is automatically
freed when the superblock is destroyed.
A new helper function, generic_show_options() is introduced, which uses
this field to display the mount options in /proc/mounts.
Another helper function, save_mount_options() may be used by
filesystems to save the options in the super block.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can use ilog2() in fs/namespace.c to compute hash_bits and hash_mask at
compile time, not runtime.
[akpm@linux-foundation.org: clean it all up]
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This also renames fs_subsys to fs_kobj to catch all current users with a
build error instead of a build warning which can easily be missed.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need a "default" ktype for a kset. We should set this
explicitly every time for each kset. This change is needed so that we
can make ksets dynamic, and cleans up one of the odd, undocumented
assumption that the kset/kobject/ktype model has.
This patch is based on a lot of help from Kay Sievers.
Nasty bug in the block code was found by Dave Young
<hidave.darkstar@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Get a snapshot of a subtree, creating private clones of vfsmounts
for all its components and release such snapshot resp.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This flag tells the .get_sb callback that this is a kern_mount() call so that
it can trust *data pointer to be valid in-kernel one. If this flag is passed
from the user process, it is cleared since the *data pointer is not a valid
kernel object.
Running a few steps forward - this will be needed for proc to create the
superblock and store a valid pid namespace on it during the namespace
creation. The reason, why the namespace cannot live without proc mount is
described in the appropriate patch.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Cc: Paul Menage <menage@google.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the mempages parameter is actually not used, they should be removed.
Now there is only files_init use the mempages parameter,
files_init(mempages);
but I don't think the adaptation to mempages in files_init is really
useful; and if files_init also changed to the prototype void (*func)(void),
the wrapper vfs_caches_init would also not need the mempages parameter.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Every file should include the headers containing the prototypes for
its global functions.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While working on unshare support for the network namespace I noticed we
were putting clone flags in an int. Which is weird because the syscall
uses unsigned long and we at least need an unsigned to properly hold all of
the unshare flags.
So to make the code consistent, this patch updates the code to use
unsigned long instead of int for the clone flags in those places
where we get it wrong today.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dup_mnt_ns() and clone_uts_ns() return NULL on failure. This is wrong,
create_new_namespaces() uses ERR_PTR() to catch an error. This means that the
subsequent create_new_namespaces() will hit BUG_ON() in copy_mnt_ns() or
copy_utsname().
Modify create_new_namespaces() to also use the errors returned by the
copy_*_ns routines and not to systematically return ENOMEM.
[oleg@tv-sign.ru: better changelog]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Cc: Serge E. Hallyn <serue@us.ibm.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Pavel Emelianov <xemul@openvz.org>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One more simple and stupid switching to the new API.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's a missing check for CAP_SYS_ADMIN in do_change_type().
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are many places in the kernel where the construction like
foo = list_entry(head->next, struct foo_struct, list);
are used.
The code might look more descriptive and neat if using the macro
list_first_entry(head, type, member) \
list_entry((head)->next, type, member)
Here is the macro itself and the examples of its usage in the generic code.
If it will turn out to be useful, I can prepare the set of patches to
inject in into arch-specific code, drivers, networking, etc.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: John McCutchan <ttb@tentacle.dhs.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's a slight problem with filesystem type representation in fuse
based filesystems.
From the kernel's view, there are just two filesystem types: fuse and
fuseblk. From the user's view there are lots of different filesystem
types. The user is not even much concerned if the filesystem is fuse based
or not. So there's a conflict of interest in how this should be
represented in fstab, mtab and /proc/mounts.
The current scheme is to encode the real filesystem type in the mount
source. So an sshfs mount looks like this:
sshfs#user@server:/ /mnt/server fuse rw,nosuid,nodev,...
This url-ish syntax works OK for sshfs and similar filesystems. However
for block device based filesystems (ntfs-3g, zfs) it doesn't work, since
the kernel expects the mount source to be a real device name.
A possibly better scheme would be to encode the real type in the type
field as "type.subtype". So fuse mounts would look like this:
/dev/hda1 /mnt/windows fuseblk.ntfs-3g rw,...
user@server:/ /mnt/server fuse.sshfs rw,nosuid,nodev,...
This patch adds the necessary code to the kernel so that this can be
correctly displayed in /proc/mounts.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sys_clone() and sys_unshare() both makes copies of nsproxy and its associated
namespaces. But they have different code paths.
This patch merges all the nsproxy and its associated namespace copy/clone
handling (as much as possible). Posted on container list earlier for
feedback.
- Create a new nsproxy and its associated namespaces and pass it back to
caller to attach it to right process.
- Changed all copy_*_ns() routines to return a new copy of namespace
instead of attaching it to task->nsproxy.
- Moved the CAP_SYS_ADMIN checks out of copy_*_ns() routines.
- Removed unnessary !ns checks from copy_*_ns() and added BUG_ON()
just incase.
- Get rid of all individual unshare_*_ns() routines and make use of
copy_*_ns() instead.
[akpm@osdl.org: cleanups, warning fix]
[clg@fr.ibm.com: remove dup_namespaces() declaration]
[serue@us.ibm.com: fix CONFIG_IPC_NS=n, clone(CLONE_NEWIPC) retval]
[akpm@linux-foundation.org: fix build with CONFIG_SYSVIPC=n]
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: <containers@lists.osdl.org>
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace appropriate pairs of "kmem_cache_alloc()" + "memset(0)" with the
corresponding "kmem_cache_zalloc()" call.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Roland McGrath <roland@redhat.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Joel Becker <Joel.Becker@oracle.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add "relatime" (relative atime) support. Relative atime only updates the
atime if the previous atime is older than the mtime or ctime. Like
noatime, but useful for applications like mutt that need to know when a
file has been read since it was last modified.
A corresponding patch against mount(8) is available at
http://userweb.kernel.org/~akpm/mount-relative-atime.txt
Signed-off-by: Valerie Henson <val_henson@linux.intel.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Karel Zak <kzak@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename 'struct namespace' to 'struct mnt_namespace' to avoid confusion with
other namespaces being developped for the containers : pid, uts, ipc, etc.
'namespace' variables and attributes are also renamed to 'mnt_ns'
Signed-off-by: Kirill Korotaev <dev@sw.ru>
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This moves the mount namespace into the nsproxy. The mount namespace count
now refers to the number of nsproxies point to it, rather than the number of
tasks. As a result, the unshare_namespace() function in kernel/fork.c no
longer checks whether it is being shared.
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create a new header file, fs/internal.h, for common definitions local to the
sources in the fs/ directory.
Move extern definitions that should be in header files from fs/*.c to
fs/internal.h or other main header files where they span directories.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Don't be crufty. Mark it __must_check too.
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts the combination of list_del(A) and list_add(A, B) to
list_move(A, B).
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extend the get_sb() filesystem operation to take an extra argument that
permits the VFS to pass in the target vfsmount that defines the mountpoint.
The filesystem is then required to manually set the superblock and root dentry
pointers. For most filesystems, this should be done with simple_set_mnt()
which will set the superblock pointer and then set the root dentry to the
superblock's s_root (as per the old default behaviour).
The get_sb() op now returns an integer as there's now no need to return the
superblock pointer.
This patch permits a superblock to be implicitly shared amongst several mount
points, such as can be done with NFS to avoid potential inode aliasing. In
such a case, simple_set_mnt() would not be called, and instead the mnt_root
and mnt_sb would be set directly.
The patch also makes the following changes:
(*) the get_sb_*() convenience functions in the core kernel now take a vfsmount
pointer argument and return an integer, so most filesystems have to change
very little.
(*) If one of the convenience function is not used, then get_sb() should
normally call simple_set_mnt() to instantiate the vfsmount. This will
always return 0, and so can be tail-called from get_sb().
(*) generic_shutdown_super() now calls shrink_dcache_sb() to clean up the
dcache upon superblock destruction rather than shrink_dcache_anon().
This is required because the superblock may now have multiple trees that
aren't actually bound to s_root, but that still need to be cleaned up. The
currently called functions assume that the whole tree is rooted at s_root,
and that anonymous dentries are not the roots of trees which results in
dentries being left unculled.
However, with the way NFS superblock sharing are currently set to be
implemented, these assumptions are violated: the root of the filesystem is
simply a dummy dentry and inode (the real inode for '/' may well be
inaccessible), and all the vfsmounts are rooted on anonymous[*] dentries
with child trees.
[*] Anonymous until discovered from another tree.
(*) The documentation has been adjusted, including the additional bit of
changing ext2_* into foo_* in the documentation.
[akpm@osdl.org: convert ipath_fs, do other stuff]
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow filesystems to decide to perform pre-umount processing whether or not
MNT_FORCE is set.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Allow a submount to be marked as being 'shrinkable' by means of the
vfsmount->mnt_flags, and then add a function 'shrink_submounts()' which
attempts to recursively unmount these submounts.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Revert commit f6422f17d3, due to
Valdis.Kletnieks@vt.edu wrote:
>
> There seems to have been a bug introduced in this changeset:
>
> Am running 2.6.17-rc3-mm1. When this changeset is applied, 'mount --bind'
> misbehaves:
>
> > # mkdir /foo
> > # mount -t tmpfs -o rw,nosuid,nodev,noexec,noatime,nodiratime none /foo
> > # mkdir /foo/bar
> > # mount --bind /foo/bar /foo
> > # tail -2 /proc/mounts
> > none /foo tmpfs rw,nosuid,nodev,noexec,noatime,nodiratime 0 0
> > none /foo tmpfs rw 0 0
>
> Reverting this changeset causes both mounts to have the same options.
>
> (Thanks to Stephen Smalley for tracking down the changeset...)
>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: <Valdis.Kletnieks@vt.edu>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The mnt_flags are propagated into do_loopback(), so that they can be stored
with the vfsmount
Signed-off-by: Herbert Poetzl <herbert@13thfloor.at>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the functions may_umount and may_umount_tree to boolean functions to
aid code readability.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I discovered on oprofile hunting on a SMP platform that dentry lookups were
slowed down because d_hash_mask, d_hash_shift and dentry_hashtable were in
a cache line that contained inodes_stat. So each time inodes_stats is
changed by a cpu, other cpus have to refill their cache line.
This patch moves some variables to the __read_mostly section, in order to
avoid false sharing. RCU dentry lookups can go full speed.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create a new file under /proc/self, called mountstats, where mounted file
systems can export information (configuration options, performance counters,
and so on). Use a mechanism similar to /proc/mounts and s_ops->show_options.
This mechanism does not violate namespace security, and is safe to use while
other processes are unmounting file systems.
Thanks to Mike Waychison for his review and comments.
Test-plan:
Test concurrent mount/unmount operations while cat'ing /proc/self/mountstats.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The Coverity checker spotted the following bug in dup_namespace():
<-- snip -->
if (!new_ns->root) {
up_write(&namespace_sem);
kfree(new_ns);
goto out;
}
...
out:
return new_ns;
<-- snip -->
Callers expect a non-NULL result to not be freed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the namespace structure is being shared, allocate a new one and copy
information from the current, shared, structure.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
fs: Use <linux/capability.h> where capable() is used.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Turn noatime and nodiratime into per-mount instead of per-sb flags.
After all the preparations this is a rather trivial patch. The mount code
needs to treat the two options as per-mount instead of per-superblock, and
touch_atime needs to be changed to check the new MNT_ flags in addition to
the MS_ flags that are kept for filesystems that are always
noatime/nodiratime but not user settable anymore. Besides that core code
only nfs needed an update because it's leaving atime updates to the server
and thus sets the S_NOATIME flag on every inode, but needs to know whether
it's a real noatime mount for an getattr optimization.
While we're at it I've killed the IS_NOATIME/IS_NODIRATIME macros that were
only used by touch_atime.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts the inode semaphore to a mutex. I have tested it on
XFS and compiled as much as one can consider on an ia64. Anyway your
luck with it might be different.
Modified-by: Ingo Molnar <mingo@elte.hu>
(finished the conversion)
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Nick Piggin