There is at least one bug in core_busy_loop(), we use r0, but it's
not in the clobber list. We were getting away with this it seems but
that was luck.
It's also fishy to be touching the stack, even if we do it below the
stack pointer. It seems we get away with it, but looking at the
generated code that may just be luck.
So move it into assembler, do all the stack handling by hand. We create
a stack frame to save the non-volatiles in, so we can muck around with
them.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
start and end should be unsigned long.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we ignore errors from our sub Makefiles. We inherited that
from the top-level selftests Makefile which aims to build and run as
many tests as possible and damn the torpedoes.
For the powerpc tests we'd instead like any errors to fail the build, so
we can automatically catch build failures.
We can achieve the best of both worlds by using -k, which tells make to
keep building when it hits an error, but still reports the error.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This provides a simple interface to trigger the firmware_class loader
to test built-in, filesystem, and user helper modes. Additionally adds
tests via the new interface to the selftests tree.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves a number of merge issues with changes in this tree and
Linus's tree at the same time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems, hot-plug tests could hang forever waiting for cpu and
memory to be ready to be offlined. A special hot-plug target is created
to run full range of hot-plug tests. In default mode, hot-plug tests run
in safe mode with a limited scope. In limited mode, cpu-hotplug test is
run on a single cpu as opposed to all hotplug capable cpus, and memory
hotplug test is run on 2% of hotplug capable memory instead of 10%. In
addition to the above change, cpu-hotplug is chnged to change processor
affinity to cpu 0 so it doesn't impact itself while the test runs.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kcmp_test.c: In function ‘main’:
kcmp_test.c:85:5: warning: format ‘%li’ expects argument of type ‘long int’, but argument 2 has type ‘int’ [-Wformat=]
ret, strerror(errno));
^
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Makefile compile linking order is incorrect causing the compile
to fail not finding librt symbols.
/tmp/cceTqwFh.o: In function `test_queue_fail':
mq_open_tests.c:(.text+0x6b): undefined reference to `mq_open'
mq_open_tests.c:(.text+0x80): undefined reference to `mq_getattr'
mq_open_tests.c:(.text+0xa2): undefined reference to `mq_close'
mq_open_tests.c:(.text+0xcf): undefined reference to `mq_unlink'
/tmp/cceTqwFh.o: In function `test_queue.constprop.6':
mq_open_tests.c:(.text+0x15a): undefined reference to `mq_open'
mq_open_tests.c:(.text+0x16f): undefined reference to `mq_getattr'
mq_open_tests.c:(.text+0x195): undefined reference to `mq_close'
mq_open_tests.c:(.text+0x1c2): undefined reference to `mq_unlink'
/tmp/cceTqwFh.o: In function `shutdown.part.0':
mq_open_tests.c:(.text.unlikely+0x5b): undefined reference to `mq_close'
mq_open_tests.c:(.text.unlikely+0x7a): undefined reference to `mq_unlink'
collect2: error: ld returned 1 exit status
make: *** [all] Error 1
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix several compile warnings - these are repeats like the ones
below:
gcc -O2 -lrt mq_open_tests.c -o mq_open_tests
mq_open_tests.c: In function ‘main’:
mq_open_tests.c:295:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 2 has type ‘rlim_t’ [-Wformat=]
printf("\tRLIMIT_MSGQUEUE(soft):\t\t%d\n", saved_limits.rlim_cur);
^
mq_open_tests.c: In function ‘shutdown’:
mq_open_tests.c:83:9: warning: ignoring return value of ‘seteuid’, declared with attribute warn_unused_result [-Wunused-result]
seteuid(0);
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix numerous compile warnings in mq_perf_tests.c. All of these
are wrong format in printfs when printing nvsec.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
on-off-test is a bash script and invoked from /bin/sh
This results in the following error:
./on-off-test.sh: 9: [: !=: unexpected operator
Changed Makefile to use bash instead.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
on-off-test is a bash script and invoked from /bin/sh
This results in the following error:
./on-off-test.sh: 9: [: !=: unexpected operator
Changed Makefile to use bash instead.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_PROVE_RCU_DELAY Kconfig parameter doesn't appear to be very
effective at finding race conditions, so this commit removes it.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
[ paulmck: Remove definition and uses as noted by Paul Bolle. ]
The test fails in the middle when it is not run as root while accessing
/proc/sys/kernel/msg_next_id. Changed it to check for root at the
beginning of the test and exit if not root.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
on-off-test uses "$UID != 0" to test for root, but $UID is a construct
specific to bash. Using /bin/sh that isn't bash results in the
following error (due to the "$UID" part expanding to nothing):
./on-off-test.sh: 9: [: !=: unexpected operator
Change Makefile to use bash instead.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
on-off-test uses "$UID != 0" to test for root, but $UID is a construct
specific to bash. Using /bin/sh that isn't bash results in the
following error (due to the "$UID" part expanding to nothing):
./on-off-test.sh: 9: [: !=: unexpected operator
Change Makefile to use bash instead.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the post-processing complains about the lack of rcutorture
output when --buildonly is set and also emits misleading messages about
kernels being started and finishing. This commit suppresses these
complaints and messages.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The CFcommon file must now be present, which makes using the current
scripts against old kernel versions cumbersome. This commit therefore
makes the CFcommon file be optional, so that old kernel versions can be
used with current torture scripts.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This gives us standardised success/failure output and also handles
killing the test if it runs forever (2 minutes).
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull more powerpc updates from Ben Herrenschmidt:
"Here are the remaining bits I was mentioning earlier. Mostly bug
fixes and new selftests from Michael (yay !). He also removed the WSP
platform and A2 core support which were dead before release, so less
clutter.
One little "feature" I snuck in is the doorbell IPI support for
non-virtualized P8 which speeds up IPIs significantly between threads
of a core"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (34 commits)
powerpc/book3s: Fix some ABIv2 issues in machine check code
powerpc/book3s: Fix guest MC delivery mechanism to avoid soft lockups in guest.
powerpc/book3s: Increment the mce counter during machine_check_early call.
powerpc/book3s: Add stack overflow check in machine check handler.
powerpc/book3s: Fix machine check handling for unhandled errors
powerpc/eeh: Dump PE location code
powerpc/powernv: Enable POWER8 doorbell IPIs
powerpc/cpuidle: Only clear LPCR decrementer wakeup bit on fast sleep entry
powerpc/powernv: Fix killed EEH event
powerpc: fix typo 'CONFIG_PMAC'
powerpc: fix typo 'CONFIG_PPC_CPU'
powerpc/powernv: Don't escalate non-existing frozen PE
powerpc/eeh: Report frozen parent PE prior to child PE
powerpc/eeh: Clear frozen state for child PE
powerpc/powernv: Reduce panic timeout from 180s to 10s
powerpc/xmon: avoid format string leaking to printk
selftests/powerpc: Add tests of PMU EBBs
selftests/powerpc: Add support for skipping tests
selftests/powerpc: Put the test in a separate process group
selftests/powerpc: Fix instruction loop for ABIv2 (LE)
...
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
The Power8 Performance Monitor Unit (PMU) has a new feature called Event
Based Branches (EBB). This commit adds tests of the kernel API for using
EBBs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Allows us to kill the test and any children it has spawned.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Correct the DSCR SPR becoming temporarily corrupted if a task is
context switched during a transaction.
The problem occurs while suspending the task and is caused by saving
the DSCR to thread.dscr after it has already been set to the CPU's
default value:
__switch_to() calls __switch_to_tm()
which calls tm_reclaim_task()
which calls tm_reclaim_thread()
which calls tm_reclaim()
where the DSCR is set to the CPU's default
__switch_to() calls _switch()
where thread.dscr is set to the DSCR
When the task is resumed, it's transaction will be doomed (as usual)
and the DSCR SPR will be corrupted, although the checkpointed value
will be correct. Therefore the DSCR will be immediately corrected by
the transaction aborting, unless it has been suspended. In that case
the incorrect value can be seen by the task until it resumes the
transaction.
The fix is to treat the DSCR similarly to the TAR and save it early
in __switch_to().
A program exposing the problem is added to the kernel self tests as:
tools/testing/selftests/powerpc/tm/tm-resched-dscr.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
CC: <stable@vger.kernel.org> [v3.10+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull powerpc updates from Ben Herrenschmidt:
"Here is the bulk of the powerpc changes for this merge window. It got
a bit delayed in part because I wasn't paying attention, and in part
because I discovered I had a core PCI change without a PCI maintainer
ack in it. Bjorn eventually agreed it was ok to merge it though we'll
probably improve it later and I didn't want to rebase to add his ack.
There is going to be a bit more next week, essentially fixes that I
still want to sort through and test.
The biggest item this time is the support to build the ppc64 LE kernel
with our new v2 ABI. We previously supported v2 userspace but the
kernel itself was a tougher nut to crack. This is now sorted mostly
thanks to Anton and Rusty.
We also have a fairly big series from Cedric that add support for
64-bit LE zImage boot wrapper. This was made harder by the fact that
traditionally our zImage wrapper was always 32-bit, but our new LE
toolchains don't really support 32-bit anymore (it's somewhat there
but not really "supported") so we didn't want to rely on it. This
meant more churn that just endian fixes.
This brings some more LE bits as well, such as the ability to run in
LE mode without a hypervisor (ie. under OPAL firmware) by doing the
right OPAL call to reinitialize the CPU to take HV interrupts in the
right mode and the usual pile of endian fixes.
There's another series from Gavin adding EEH improvements (one day we
*will* have a release with less than 20 EEH patches, I promise!).
Another highlight is the support for the "Split core" functionality on
P8 by Michael. This allows a P8 core to be split into "sub cores" of
4 threads which allows the subcores to run different guests under KVM
(the HW still doesn't support a partition per thread).
And then the usual misc bits and fixes ..."
[ Further delayed by gmail deciding that BenH is a dirty spammer.
Google knows. ]
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (155 commits)
powerpc/powernv: Add missing include to LPC code
selftests/powerpc: Test the THP bug we fixed in the previous commit
powerpc/mm: Check paca psize is up to date for huge mappings
powerpc/powernv: Pass buffer size to OPAL validate flash call
powerpc/pseries: hcall functions are exported to modules, need _GLOBAL_TOC()
powerpc: Exported functions __clear_user and copy_page use r2 so need _GLOBAL_TOC()
powerpc/powernv: Set memory_block_size_bytes to 256MB
powerpc: Allow ppc_md platform hook to override memory_block_size_bytes
powerpc/powernv: Fix endian issues in memory error handling code
powerpc/eeh: Skip eeh sysfs when eeh is disabled
powerpc: 64bit sendfile is capped at 2GB
powerpc/powernv: Provide debugfs access to the LPC bus via OPAL
powerpc/serial: Use saner flags when creating legacy ports
powerpc: Add cpu family documentation
powerpc/xmon: Fix up xmon format strings
powerpc/powernv: Add calls to support little endian host
powerpc: Document sysfs DSCR interface
powerpc: Fix regression of per-CPU DSCR setting
powerpc: Split __SYSFS_SPRSETUP macro
arch: powerpc/fadump: Cleaning up inconsistent NULL checks
...
This adds several behavioral tests to sysctl string and number writing
to detect unexpected cases that behaved differently when the sysctl
kernel.sysctl_writes_strict != 1.
[ original ]
root@localhost:~# make test_num
== Testing sysctl behavior against /proc/sys/kernel/domainname ==
Writing test file ... ok
Checking sysctl is not set to test value ... ok
Writing sysctl from shell ... ok
Resetting sysctl to original value ... ok
Writing entire sysctl in single write ... ok
Writing middle of sysctl after synchronized seek ... FAIL
Writing beyond end of sysctl ... FAIL
Writing sysctl with multiple long writes ... FAIL
Writing entire sysctl in short writes ... FAIL
Writing middle of sysctl after unsynchronized seek ... ok
Checking sysctl maxlen is at least 65 ... ok
Checking sysctl keeps original string on overflow append ... FAIL
Checking sysctl stays NULL terminated on write ... ok
Checking sysctl stays NULL terminated on overwrite ... ok
make: *** [test_num] Error 1
root@localhost:~# make test_string
== Testing sysctl behavior against /proc/sys/vm/swappiness ==
Writing test file ... ok
Checking sysctl is not set to test value ... ok
Writing sysctl from shell ... ok
Resetting sysctl to original value ... ok
Writing entire sysctl in single write ... ok
Writing middle of sysctl after synchronized seek ... FAIL
Writing beyond end of sysctl ... FAIL
Writing sysctl with multiple long writes ... ok
make: *** [test_string] Error 1
[ with CONFIG_PROC_SYSCTL_STRICT_WRITES ]
root@localhost:~# make run_tests
== Testing sysctl behavior against /proc/sys/kernel/domainname ==
Writing test file ... ok
Checking sysctl is not set to test value ... ok
Writing sysctl from shell ... ok
Resetting sysctl to original value ... ok
Writing entire sysctl in single write ... ok
Writing middle of sysctl after synchronized seek ... ok
Writing beyond end of sysctl ... ok
Writing sysctl with multiple long writes ... ok
Writing entire sysctl in short writes ... ok
Writing middle of sysctl after unsynchronized seek ... ok
Checking sysctl maxlen is at least 65 ... ok
Checking sysctl keeps original string on overflow append ... ok
Checking sysctl stays NULL terminated on write ... ok
Checking sysctl stays NULL terminated on overwrite ... ok
== Testing sysctl behavior against /proc/sys/vm/swappiness ==
Writing test file ... ok
Checking sysctl is not set to test value ... ok
Writing sysctl from shell ... ok
Resetting sysctl to original value ... ok
Writing entire sysctl in single write ... ok
Writing middle of sysctl after synchronized seek ... ok
Writing beyond end of sysctl ... ok
Writing sysctl with multiple long writes ... ok
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current scripting only keeps track of the git SHA-1 of the current
HEAD. This can cause confusion in cases where testing ran in a git
tree where changes had not yet been checked in. This commit therefore
also records the output of "git diff HEAD" to provide the information
needed to reconstruct the source tree that was tested.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit ensures that RCU-sched primitives are tested in
TREE_PREEMPT_RCU kernels, a combination that was previously omitted.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The kvm-test-1-run.sh currently counts "sleep 1" commands to detect
hangs. This can fail spectacularly on busy systems, where "sleep 1"
might take far longer than one second to complete. This commit
therefore changes hang detection to use elapsed time measurements.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The reaction of kvm-recheck.sh is obscure at best, and easy to miss
completely. This commit therefore prints "BUG: Build failed" in the
summary at the end of a run. This commit also adds the line of dashes
in cases where performance info is not available, and also avoids
printing nonsense diagnostics in cases where some of the normal test
output is not available. In addition, this commit saves off the .config
file even when the build fails.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit adds a CONFIG_RCU_TRACE=y version of TREE02 for debugging
purposes.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Currently, the scripts hard-code arch/x86/boot/bzImage, which does not
work well for other architectures. This commit therefore provides a
identify_boot_image function that selects the correct bzImage location
relative to the top of the Linux source tree. This commit also adds a
--bootimage argument that allows selecting some other file, for example,
"vmlinux".
This change requires that the definition of the QEMU variable be
computed earlier in order to identify where to look for the boot image
when it comes time to copy it to the results directory.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit applies quotes to permit multi-word --qemu-args and
--bootargs arguments.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The current script does record qemu diagnostics, but the user has to
know where to look for them. This commit therefore puts them into the
Warnings file so that kvm-recheck.sh will display them. This change is
especially useful if you are in the habit of killing the qemu process
when you realize that you messed something up, but then later on wonder
why the process terminated early.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
In a normal torture-test run, the script inherits its environment
variables, but this does not work when producing a script that is
to run later. Therefore, definitions and exports are prepended to
a dryrun script but not to a script that is run immediately. This
commit reconciles this by placing definitions and exports at the
beginning of the script in both cases.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Conflicts:
tools/testing/selftests/rcutorture/bin/kvm.sh
The scripts produced by kvm.sh's "--dryrun script" argument were intended
for debugging rather than to run, but it is easier to debug if the script
output matches exactly what is run. This commit therefore makes this
script runnable.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The torture tests need to set specific values for their respective
Kconfig options (e.g., CONFIG_LOCK_TORTURE_TEST), and must therefore
filter any conflicting definitions from the Kconfig fragment
file. Unfortunately, the code in kvm-build.sh was looking only for
CONFIG_RCU_TORTURE_TEST. This commit therefore handles the general case
of CONFIG_[A-Z]*_TORTURE_TEST.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit makes the torture scripts a bit more RCU-independent.
It also removes a redundant export of this same shell variable.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit makes the torture scripts a bit more RCU-independent.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit makes the torture scripts a bit more RCU-independent.
It also drops an redundant "export" statement.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit makes the torture scripts a bit more RCU-independent.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit makes the torture scripts a bit more RCU-independent by
changing RCU_BUILDONLY to TORTURE_BUILDONLY. It also removes an
unnecessary export command.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit makes the torture scripts a bit more RCU-independent.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit makes the torture scripts a bit more RCU-independent by
changing RCU_KMAKE_ARG to TORTURE_KMAKE_ARG. It also removes the
unnecessary export command.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Some environments require some variation on "make defconfig" to initialize
the .config file. This commit therefore adds a --defconfig argument to
allow this to be specified. The default value is of course "defconfig".
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit makes the torture scripts a bit more RCU-independent.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
It can be a bit jarring to see a locking test complain about RCU, so
this commit renames parse-rcutorture.sh to parse-torture.sh and makes
the messages it emits more generic.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit makes the output of "--dryrun sched" more user-friendly,
clearly indicating the batch starts.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The --builddir and --relbuilddir options were initially intended to handle
parallel tests. However, since commit 43e38ab3d5 (Enable concurrent
rcutorture runs), the script manages multiple build directories as
needed for parallel testing. This commit therefore removes these two
obsolete options.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The testsuite covers classic and internal BPF instructions.
It is particularly useful for JIT compiler developers.
Adds to "net" selftest target.
The testsuite can be used as a set of micro-benchmarks.
It measures execution time of each BPF program in nsec.
This patch adds core framework.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the more robust config_bisect, the documentation is out of
date and needs to be updated.
The new rewrite allows for finding missing configs and such, and
is much more robust to use.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
After the rewrite of the config bisect, there were several unused
functions that can be removed.
One of the unused functions printed out the failed config nicer than
what the rewrite did, so I kept that and used it to output the
bad config.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The new rewrite left out the CONFIG_BISECT_CHECK, which allows the
user to test that their "bad" config still is bad and their "good"
config still is good. This is especially important as the configs
are passed through a "make oldconfig" to update them with the lastest
kernel. Things could change that causes a bad config to work, or a
good config to break. The check is done after the configs have run
through the oldconfig processing.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
I never liked the way config-bisect worked. I would assume the bad config
had some config that broke the system. But it would not work if the bad
config just happened to be missing something that the good config had.
I rewrote the config-bisect to do this properly. It does a diff of the two
configs, and sets half of the configs that are in one and not the other.
The way it works is that when it "sets", it really just makes one copy
what the other has. That is, a "set" can be setting a:
# CONFIG_FOO is not set
Basically, it looks at the differences between the two files and makes
them similar until it comes down to one config that makes it work or
not work depending on if it is set or not.
Note, if more than one config change makes the bad config not work, it
will only find one of them. But this is true with all bisect logic.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Some cleanup for improving readability as follows.
- Initialize $ktest_config at its definition.
- Put parentheses around the `config-file' argument in the usage message
because it's a optional one.
- Rename get_ktest_config{,s} to more descriptive get_mandatory_config{,s}.
Link: http://lkml.kernel.org/r/87fvmr30kb.wl%satoru.takeuchi@gmail.com
Signed-off-by: Satoru Takeuchi <satoru.takeuchi@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If we'd like to set the redirect target file of run_command(),
we should define $redirect before calling this function and should undef it
after calling this function. Since it's user-unfriendly, add 2nd parameter of
run_command() for this purpose.
Link: http://lkml.kernel.org/r/87vbvwokq8.wl%satoru.takeuchi@gmail.com
Signed-off-by: Satoru Takeuchi <satoru.takeuchi@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
CLOSE_CONSOLE_SIGNAL to the kvm.conf file, as the kvm guest requires
a different signal than a normal console uses.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTOuRXAAoJEKQekfcNnQGuukQH/3x8/rCkDSfn44zdA0srumm6
1yKfn3QBgspoxi78zypPLiCmSKLMVWpKOfFwyN3jaQSy7/UfoSTLEEPKcKIEdaUe
2HWMIO2OxToghRfo1WSA899p0MPtw44J7gy6bvLv9qMl8yyNE9KBotEQTT2vJ+ya
ODMXNhy4lmRvz3jHFLu4Z62PsJ/YQvHzehgb1N62EkwvBwtaCu8CAt1qvN5B9EnO
wWCYJ+DfdnXwNhA+e7w4hOTxc8thO4bRXFKVs50ST7zMHWNtTxs+WODlmJKQGUUS
SNeZcwkh/BBdM9MYIQQUpqUQ16lEh7/6fVdFMHpCK2IL32T0wNwpFf3A+ZTnRoo=
=b4GL
-----END PGP SIGNATURE-----
Merge tag 'ktest-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull single ktest fix from Steven Rostedt:
"This just contains a single update by Satoru Takeuchi, which adds
CLOSE_CONSOLE_SIGNAL to the kvm.conf file, as the kvm guest requires a
different signal than a normal console uses"
* tag 'ktest-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Set CLOSE_CONSOLE_SIGNAL in the kvm.conf
Pull main powerpc updates from Ben Herrenschmidt:
"This time around, the powerpc merges are going to be a little bit more
complicated than usual.
This is the main pull request with most of the work for this merge
window. I will describe it a bit more further down.
There is some additional cpuidle driver work, however I haven't
included it in this tree as it depends on some work in tip/timer-core
which Thomas accidentally forgot to put in a topic branch. Since I
didn't want to carry all of that tip timer stuff in powerpc -next, I
setup a separate branch on top of Thomas tree with just that cpuidle
driver in it, and Stephen has been carrying that in next separately
for a while now. I'll send a separate pull request for it.
Additionally, two new pieces in this tree add users for a sysfs API
that Tejun and Greg have been deprecating in drivers-core-next.
Thankfully Greg reverted the patch that removes the old API so this
merge can happen cleanly, but once merged, I will send a patch
adjusting our new code to the new API so that Greg can send you the
removal patch.
Now as for the content of this branch, we have a lot of perf work for
power8 new counters including support for our new "nest" counters
(also called 24x7) under pHyp (not natively yet).
We have new functionality when running under the OPAL firmware
(non-virtualized or KVM host), such as access to the firmware error
logs and service processor dumps, system parameters and sensors, along
with a hwmon driver for the latter.
There's also a bunch of bug fixes accross the board, some LE fixes,
and a nice set of selftests for validating our various types of copy
loops.
On the Freescale side, we see mostly new chip/board revisions, some
clock updates, better support for machine checks and debug exceptions,
etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (70 commits)
powerpc/book3s: Fix CFAR clobbering issue in machine check handler.
powerpc/compat: 32-bit little endian machine name is ppcle, not ppc
powerpc/le: Big endian arguments for ppc_rtas()
powerpc: Use default set of netfilter modules (CONFIG_NETFILTER_ADVANCED=n)
powerpc/defconfigs: Enable THP in pseries defconfig
powerpc/mm: Make sure a local_irq_disable prevent a parallel THP split
powerpc: Rate-limit users spamming kernel log buffer
powerpc/perf: Fix handling of L3 events with bank == 1
powerpc/perf/hv_{gpci, 24x7}: Add documentation of device attributes
powerpc/perf: Add kconfig option for hypervisor provided counters
powerpc/perf: Add support for the hv 24x7 interface
powerpc/perf: Add support for the hv gpci (get performance counter info) interface
powerpc/perf: Add macros for defining event fields & formats
powerpc/perf: Add a shared interface to get gpci version and capabilities
powerpc/perf: Add 24x7 interface headers
powerpc/perf: Add hv_gpci interface header
powerpc: Add hvcalls for 24x7 and gpci (Get Performance Counter Info)
sysfs: create bin_attributes under the requested group
powerpc/perf: Enable BHRB access for EBB events
powerpc/perf: Add BHRB constraint and IFM MMCRA handling for EBB
...
Pull RCU updates from Ingo Molnar:
"Main changes:
- Torture-test changes, including refactoring of rcutorture and
introduction of a vestigial locktorture.
- Real-time latency fixes.
- Documentation updates.
- Miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (77 commits)
rcu: Provide grace-period piggybacking API
rcu: Ensure kernel/rcu/rcu.h can be sourced/used stand-alone
rcu: Fix sparse warning for rcu_expedited from kernel/ksysfs.c
notifier: Substitute rcu_access_pointer() for rcu_dereference_raw()
Documentation/memory-barriers.txt: Clarify release/acquire ordering
rcutorture: Save kvm.sh output to log
rcutorture: Add a lock_busted to test the test
rcutorture: Place kvm-test-1-run.sh output into res directory
rcutorture: Rename TREE_RCU-Kconfig.txt
locktorture: Add kvm-recheck.sh plug-in for locktorture
rcutorture: Gracefully handle NULL cleanup hooks
locktorture: Add vestigial locktorture configuration
rcutorture: Introduce "rcu" directory level underneath configs
rcutorture: Rename kvm-test-1-rcu.sh
rcutorture: Remove RCU dependencies from ver_functions.sh API
rcutorture: Create CFcommon file for common Kconfig parameters
rcutorture: Create config files for scripted test-the-test testing
rcutorture: Add an rcu_busted to test the test
locktorture: Add a lock-torture kernel module
rcutorture: Abstract kvm-recheck.sh
...
A failed msgget causes the test to return an uninitialised value in ret.
Assign ret to -errno on error exit.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Davidlohr Bueso <davidlohr@hp.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Turn Anton's memcpy / copy_tofrom_user test into something that can
live in tools/testing/selftests.
It requires one turd in arch/powerpc/lib/memcpy_64.S, but it's pretty
harmless IMHO.
We are sailing very close to the wind with the feature macros. We define
them to nothing, which currently means we get a few extra nops and
include the unaligned calls.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As mentioned at commit 5a5d8e4844, we can't terminate 'virsh console'
with the default signal(INT). So it's better to set CLOSE_CONSOLE_SIGNAL
in the kvm.conf.
Link: http://lkml.kernel.org/r/8738jatylb.wl%satoru.takeuchi@gmail.com
Signed-off-by: Satoru Takeuchi <satoru.takeuchi@gmail.com>
[ Typo fixed by ]
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This commit logs the progress text that kvm.sh outputs, improving
after-the-fact troubleshooting.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The output of each kvm-test-1-run.sh script is placed into a file
whose name parallels that of the build directory. This means that
the kvm-test-1-run.sh output is overwritten by later run. This
commit therefore places the kvm-test-1-run.sh output into the
per-test-case directory in the "res" hierarchy.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
It used to be that:
git ls-files "*Kconfig*"
would find all Kconfig files and would only find Kconfig files. This
commit renames TREE_RCU-Kconfig.txt to TREE_RCU-kconfig.txt so that this
is once again true.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit adds the kvm-recheck-lock.sh plug-in for locktorture to
print out lock-specific progress statistics.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit adds a trivial set of configuration files for lock
torturing.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit uses the standard software ploy of introducing another
level of indirection below the configs directory. This allows each
torture-test suite to have its own set of Kconfig files, boot parameters,
and version-specific scripts. Initially, we have only rcu, but lock
will follow soonish.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The kvm-test-1-rcu.sh is not specific to RCU, so this commit renames it
to kvm-test-1-run.sh.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The current set of functions in ver_functions.sh have APIs that are
specific to RCU. This commit therefore makes an RCU-independent function
that outputs version-specific boot arguments. This has the benefit that
a test-type-independent call in kvm-test-1-rcu.sh can now handle any type
of test, given a test-type-specific set of files in a configs directory.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Currently, CONFIG_RCU_TORTURE_TEST=y is hardcoded into the
kvm-test-1-rcu.sh script and CONFIG_PRINTK_TIME=y is mentioned in each
and every configs file. This commit creates a CFcommon file for these
two Kconfig parameters, and modifies kvm-test-1-rcu.sh to copy this new
file into the .config file during the build. This change will allow
these scripts to operate on torture types other than just rcutorture.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit adds a pair of files in the configs directory to allow
test-the-test runs of rcutorture via a "--configs BUSTED" argument to
the kvm.sh script.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit creates a plug-in to allow kvm-recheck.sh to process
non-rcutorture console output.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit prevents the results directory from being created for
dryruns. However, a script generated from a dryrun will create
the results directory should it be run.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org
This commit adds a "(!)" flag after the number of CPUs required by a
given test if that test requires more than the available number of CPUs.
Note that these flags appear only when the number of CPUs is specified
using the --cpus argument. In the absence of a --cpus argument, no
tests are flagged.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Running the standard set of rcutorture tests on 24 CPUs results in
the following sub-optimal schedule:
----start batch----
TREE07 16
----start batch----
TREE08 16
SRCU-P 8
----start batch----
TREE01 8
TREE02 8
TREE03 8
----start batch----
TREE04 8
TREE05 8
TREE06 8
----start batch----
SRCU-N 4
TINY01 1
TINY02 1
TREE09 1
If one of the eight-CPU runs were to be moved into the first batch,
the test suite would complete in four batches rather than five.
This commit therefore uses a greedy algorithm to re-order the test
entries so that the sequential batching will produce an optimal schedule
in this case:
----start batch----
TREE07 16
SRCU-P 8
----start batch----
TREE08 16
TREE01 8
----start batch----
TREE02 8
TREE03 8
TREE04 8
----start batch----
TREE05 8
TREE06 8
SRCU-N 4
TINY01 1
TINY02 1
TREE09 1
Please note that this is still not an optimal bin-packing algorithm,
however, it does produce optimal solutions for most common scenarios.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit fixes handling numbering of multiple runs of the same test
so as to disambiguate output.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Actual rcutorture tests take considerable time and machine resources,
so it is inconvenient to actually do an rcutorture run when optimizing
the bin-packing algorithm. This commit therefore adds a --dryrun
argument, which defaults to doing a run, but for which "sched"
says to simply print the run schedule and "script" dumps the script
without running it.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The message complains about a build directory when it should instead
be complaining about the results directory, so this commit fixes it.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The rcutorture tests run by default range from using one CPU to using
sixteen of them. Therefore, rcutorture testing could be sped up
significantly simply by running the kernels in parallel. Building
them in parallel is not all that helpful: "make -j" is usually a
better bet. So this commit takes a new "--cpus" argument that
specifies how many CPUs rcutorture is permitted to use for its
parallel runs. The default of zero does sequential runs as before.
The bin-packing is minimal, and will be grossly suboptimal for
some configurations. However, powers of two work reasonably well.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Both SRCU-P and SRCU-N specify eight CPUs, which results in four
iterations for a parallel run on 32 CPUs. This commit reduces SRCU-N
to four CPUs (but leaving SRCU-P at eight) to speed up parallel runs,
while maintaining essentially the same test coverage.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Currently, most qemu flags are calculated in kvm-test-1-rcu.sh,
except that -nographics is set up by kvm.sh. This commit promotes
one-stop shopping by consolidating the determination of qemu flags into
kvm-test-1-rcu.sh.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Parallel rcutorture runs is valuable on large systems, but it is not a
good idea to do (say) five builds in parallel if each build believes it
has the whole system at its disposal, especially if the system is shared.
It is also bad to restrict the build to (say) a single CPU just because
the corresponding rcutorture run uses only a single CPU. This commit
therefore adds a kvm-test-1-rcu.sh ability to pause after the build
completes, which will allow kvm.sh to do a number of builds serially
(with each build thus having the full system at its disposal), then
allow the rcutorture runs to proceed in parallel.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Currently, most boot flags are calculated in kvm-test-1-rcu.sh, except
that rcutorture.test_no_idle_hz and rcutorture.verbose are set up by
kvm.sh. This commit promotes one-stop shopping by consolidating the
determination of boot flags into kvm-test-1-rcu.sh.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Although the script name and arguments are logged in the results directory,
it is more convenient to see it in the output. This commit therefore
adds the output of this information.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Sometime problems can manifest themselves as unusually slow grace periods.
This commit therefore prints the number of rcutorture updates during the
test and the number per second. These statistics are harvested from the
config.out and qemu-cmd files, and are silently omitted if these files
are not available, as would be the case if there was a build failure or
a boot-time hang.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
To help avoid an architecture failing to correctly check kernel/user
boundaries when handling copy_to_user, copy_from_user, put_user, or
get_user, perform some simple tests and fail to load if any of them
behave unexpectedly.
Specifically, this is to make sure there is a way to notice if things
like what was fixed in commit 8404663f81 ("ARM: 7527/1: uaccess:
explicitly check __user pointer when !CPU_USE_DOMAINS") ever regresses
again, for any architecture.
Additionally, adds new "user" selftest target, which loads this module.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull RCU updates from Ingo Molnar:
- add RCU torture scripts/tooling
- static analysis improvements
- update RCU documentation
- miscellaneous fixes
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (52 commits)
rcu: Remove "extern" from function declarations in kernel/rcu/rcu.h
rcu: Remove "extern" from function declarations in include/linux/*rcu*.h
rcu/torture: Dynamically allocate SRCU output buffer to avoid overflow
rcu: Don't activate RCU core on NO_HZ_FULL CPUs
rcu: Warn on allegedly impossible rcu_read_unlock_special() from irq
rcu: Add an RCU_INITIALIZER for global RCU-protected pointers
rcu: Make rcu_assign_pointer's assignment volatile and type-safe
bonding: Use RCU_INIT_POINTER() for better overhead and for sparse
rcu: Add comment on evaluate-once properties of rcu_assign_pointer().
rcu: Provide better diagnostics for blocking in RCU callback functions
rcu: Improve SRCU's grace-period comments
rcu: Fix CONFIG_RCU_FANOUT_EXACT for odd fanout/leaf values
rcu: Fix coccinelle warnings
rcutorture: Stop tracking FSF's postal address
rcutorture: Move checkarg to functions.sh
rcutorture: Flag errors and warnings with color coding
rcutorture: Record results from repeated runs of the same test scenario
rcutorture: Test summary at end of run with less chattiness
rcutorture: Update comment in kvm.sh listing typical RCU trace events
rcutorture: Add tracing-enabled version of TREE08
...
o Add config to modify the signal to terminate console
o Update to documentation (missing some config options)
o Add KERNEL_VERSION variable to use for other configs
o Add '=~' to let configs eval other configs
o Add BISECT_TRIES to run multiple tests per git bisect good
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJS3UMjAAoJEKQekfcNnQGuU/YH/RdTp8o6GgHfBans6vG588mZ
CoTOhfYH9loGTAcs8JqKt0sIBaPDmdF1Qur+nthBJ/vqyFSpRtaoCLTTvNTb8Snh
Wia5DEpi4BnfH3TMyMqNVCyXJjO8wkxq7bv5wB1+pqVnIDADlX5xejOVCDms2scm
EUXQeZx38KrFHH2ZvrjzjrGjIboKB/vTriqF8Q/Vmu0lRYo+Lt6HkDUEJEehxeLz
oU+oQOuep5ABo1APMYIml9YZqBeJJuCeqKd75T3QfgWyyCaYLv1ggHXG/bymBROX
uTd/RK3lKC/ODkVi9u57a4djptYYUW6mTDkUcLO3lZhqhVKqSiOQt0B9Bw/JTdQ=
=+mEf
-----END PGP SIGNATURE-----
Merge tag 'ktest-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull ktest updates from Steven Rostedt:
"Here's some basic updates to ktest.pl. They include:
- add config to modify the signal to terminate console
- update to documentation (missing some config options)
- add KERNEL_VERSION variable to use for other configs
- add '=~' to let configs eval other configs
- add BISECT_TRIES to run multiple tests per git bisect good"
* tag 'ktest-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Add BISECT_TRIES to bisect test
ktest: Add eval '=~' command to modify variables in config file
ktest: Add special variable ${KERNEL_VERSION}
ktest: Add documentation of CLOSE_CONSOLE_SIGNAL
ktest: Make the signal to terminate the console configurable
For those cases that it takes several tries to hit a bug, it would be
useful for ktest.pl to try a test multiple times before it considers
the test as a pass. To accomplish this, BISECT_TRIES ktest config
option has been added. It is default to one, as most of the time a
bisect only needs to try a test once. But the user can now up this
to make ktest run a given test multiple times. The first failure
that is detected will set a bisect bad. It only repeats on success.
Note, as with all race bugs, there's no guarantee that if it succeeds,
it is really a good bisect. But it helps in case the bug is somewhat
reliable.
You can set BISECT_TRIES to zero, and all tests will be considered
good, unless you also set BISECT_MANUAL.
Suggested-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
With the added variable ${KERNEL_VERSION}, it is useful to be
able to use parts of it for other variables.
For example, if you want to create a warnings file for each major
kernel version to test sub versions against you can create
your warnings file with like this:
WARNINGS_FILE = warnings-file-${KERNEL_VERSION}
But this may add 3.8.12 or something, and we want all 3.8.* to
use the same file, and 3.10.* to use another file, and so on.
With the eval command we can, by adding:
WARNINGS_FILE =~ s/(-file-\d+\.\d+).*/$1/
Which will chop off the extra characters after the 3.8.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add a special variable that can be used in other variables called
${KERNEL_VERSION}. This will embed the current kernel version into
the variable. For example:
WARNINGS_FILE = ${OUTPUT_DIR}/warnings-${KERNEL_VERSION}
If the current version is v3.8 then the WARNINGS_FILE will become
${OUTPUT_DIR}/warnings-v3.8
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
All of the rcutorture scripts has the usual GPL header, which contains
a long-obsolete postal address for FSF. To avoid the need to track the
FSF office's movements, this commit substitutes the URL where GPL may
be found.
Reported-by: Greg KH <gregkh@linuxfoundation.org>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The output of the rcutorture scripts often requires interpretation, so
this commit simplifies this interpretation by tagging messages as
BUGs (colored red) or WARNINGs (colored yellow).
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Repeatedly running a given test, for example, by repeating the name
as in "--configs "TREE08 TREE08 TREE08" records the results only of
the last run of this test. This is because the earlier results are
overwritten by the later results.
This commit therefore checks for earlier results, using numbered
file extensions to distinguish multiple runs. The earlier example
would therefore create directories TREE01, TREE01.2, and TREE01.3.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
The commit causes kvm.sh to invoke kvm-recheck.sh at the end of each
run, and causes kvm-recheck.sh to print only the name of the test, not
the full path to the corresponding Kconfig file.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
The TREE08 Kconfig fragment does not enable tracing, which is appropriate
for its test case. However, this can be inconvenient in cases where
TREE08 locates RCU bugs. This commit therefore adds a TREE08-T that
differs from TREE08 only in enabling CONFIG_RCU_TRACE.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
This commit adds the --kmake-arg to kvm.sh, which allows passing in
things like "V=1" to see the build commands, as well as enabling the
CROSS_COMPILE= make macro used for cross-building.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
This commit adds the --no-initrd argument to kvm.sh, which permits
initrd to be contained in a root partition specified by the --bootargs
argument. Without --no-initrd, the kernel build expects an initrd
directory in the same rcutorture directory that contains bin and configs.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
This commits adds the --qemu-args argument to kvm.sh that is required
to pass boot devices down through to qemu.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
This commit allows easy specification of trace_event lists, among other
things.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
This commit adds --buildonly, which does the builds specified by the
--configs argument, but does not boot or test the resulting kernels.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Don't grab the configuration fragment from the configs directory because
it might well have been changed since the test was run. Instead, use
the ConfigFragment file that was placed in the results directory.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
As it stands, the default kernel boot parameters generated from
the Kconfig fragment will override any supplied with the .boot
file that can optionally accompany a Kconfig fragment. Rearrange
ordering to permit the specific .boot arguments to override those
generated by analyzing the Kconfig fragment.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
This commit expands the checks for what architecture is running to generate
additional qemu-system- commands, then uses the resulting qemu-system-
command name to choose different qemu arguments as needed for different
architectures.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
The --rcu-kvm argument was intended to allow the scripts to live in
an alternate location. Unfortunately, this prevents the kvm.sh script
from using common functions until after it finished parsing arguments,
because it doesn't know where to find them until then. However, "cp -a"
and "ln -s" work pretty well, so lack of an --rcu-kvm argument can be
easily worked around.
This commit therefore removes this argument.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
The qemu -name argument doesn't seem to be useful in this environment,
so this commit removes it.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
The task of working out which flavor of qemu to use gets more complex
as more types of CPUs are supported. Adding Power makes three in addition
to 32-bit and 64-bit x86, so it is time to pull this out into a function.
This commit therefore creates an identify_qemu function and also adds
a --qemu-cmd command-line argument for the inevitable case where the
identify_qemu cannot figure it out.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
The commit uses configcheck.sh from within configinit.sh, replacing the
imperfect inline expansion that was there before.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
This commit drops no-longer-needed diagnostics from the output. Some of
them are retained in logfiles, in case they are ever needed.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
The TINY_RCU test cases were first put in place many years ago, and have
been incrementally modified rather than being reworked. This commit
therefore completes a long-overdue reworking of the TINY_RCU test cases.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
The TREE_RCU test cases were first put in place many years ago, and have
been incrementally modified rather than being reworked. This commit
therefore completes a long-overdue reworking of the TREE_RCU test cases.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Use .boot facility to ease inclusion of SRCU into automated testing.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
The v3.12 version of the kernel added the CONFIG_NO_HZ_FULL_SYSIDLE
Kconfig parameter, so this commit adds a version transition at that
point.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Some Kconfig fragments require rcutorture module parameters to
do optimal testing, for example, a configuration for SRCU would
need rcutorture.torture_type=srcu. This commit therefore adds a
per-Kconfig-fragment boot-parameter capability.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Different Kconfig parameters apply to different kernel versions, as
do different rcutorture module parameters. This commit allows the
rcutorture test scripts to adjust for different kernel versions.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Allow datestamp to be specified to allow tests to be broken up and run
in parallel.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
This commit adds the test framework that I used to test RCU under KVM.
This consists of a group of scripts and Kconfig fragments.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
The sample.conf file needs to document all available options.
With the new CLOSE_CONSOE_SIGNAL option, it too needs to be
document.
Cc: Satoru Takeuchi <satoru.takeuchi@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Currently ktest sends SIGINT to terminate the console.
However, there are consoles which do not exit by this signal, for example,
in my case, "virsh console <guest OS>". In such case, ktest is blocked in
close_console(). It prevents this automate test.
This patch adds new option CLOSE_CONSOLE_SIGNAL which mean the
signal to terminate the console. Since its default value is "INT",
the original behavior isn't changed.
Link: http://lkml.kernel.org/r/87zjol8pl5.wl%satoru.takeuchi@gmail.com
Signed-off-by: Satoru Takeuchi <satoru.takeuchi@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
not compiled for ages, and recent versions of gcc for it are broken.
Remove support for it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJSev31AAoJEMsfJm/On5mBzSAQAKRBYLqtf3nJGm9pXGDhZPGG
7KSQ8S11pg/wnXYW6P/XJhFRBrYkOOCeqVKQHtmxG8MmXQkkOz95rsIvBbUzU/FT
yJAPKpOHdh1yLhBGgCj3WhGtjVwpbut1/y9n2M5SpGautUgxfLj9fJiswSJx0n7t
VRWKwfIpBFPLPs9w6hdDf94tIXhSX8Me2gd3LDCPBEQ2SZYd8rtBasYtDeC2+FLa
Xow4ZQrCU7hpYscSUFzJpok35hl7weGhJ9jjXwtic4byFHvdiyHUwCOaEWC0hqNi
fOLWFbvBogqjyAktfZhfyL9R9/7lGlLshLQNmJWR3bO+nCJ21h9ATw0R4gLBdT4/
lzLRnJ/4GdtbvmdqRxNjxxR4zHkZ+tE8HmaCmUzvqGfQyA5sJNBRrBDcWLUOVlO9
0iIZsJBZjSQXKXSk9P5xH4G0tlbAFEUnEHKsrt/mgsD9Z3SgbPKAIWSBAJA0AMQk
DXZaXrBRilXOPUCZASZfmK8AQFC1GYB0tz7nT4x1mjT2/JClgG2kHCAGhNmI+CbK
l9VRIgBydppLFPOGhZLSNGQp29xBhw9JgOVns4a1k7kJQEw9ht38h8Q2ckRYxXhP
/z53eZKMQk62quWlyLRgR9mWqZc2CIifLVdFjiOELMh7wKPwL6eGrrrGBDbPtctS
PX5K26geb0oA3ZMjpBLr
=V6n6
-----END PGP SIGNATURE-----
Merge tag 'h8300-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull h8300 platform removal from Guenter Roeck:
"The patch series has been in -next for more than one relase cycle. I
did get a number of Acks, and no objections.
H8/300 has been dead for several years, the kernel for it has not
compiled for ages, and recent versions of gcc for it are broken.
Remove support for it"
* tag 'h8300-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
CREDITS: Add Yoshinori Sato for h8300
fs/minix: Drop dependency on H8300
Drop remaining references to H8/300 architecture
Drop MAINTAINERS entry for H8/300
watchdog: Drop references to H8300 architecture
net/ethernet: Drop H8/300 Ethernet driver
net/ethernet: smsc9194: Drop conditional code for H8/300
ide: Drop H8/300 driver
Drop support for Renesas H8/300 (h8300) architecture
The err variable is intended to receive the timer_create() return before
checking it
Signed-off-by: Felipe Pena <felipensp@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H8/300 has been dead for several years, and the kernel for it
has not compiled for ages. Drop support for it.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This commit adds a test of instruction counting using the PMU on powerpc.
Although the bulk of the code is architecture agnostic, the code needs to
run a precisely sized loop which is implemented in assembler.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This commit adds support code used by upcoming powerpc tests.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This commit adds a powerpc subdirectory to tools/testing/selftests,
for tests that are powerpc specific.
On other architectures nothing is built. The makefile supports cross
compilation if the user sets ARCH and CROSS_COMPILE.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
Pull timer core updates from Thomas Gleixner:
"The timer changes contain:
- posix timer code consolidation and fixes for odd corner cases
- sched_clock implementation moved from ARM to core code to avoid
duplication by other architectures
- alarm timer updates
- clocksource and clockevents unregistration facilities
- clocksource/events support for new hardware
- precise nanoseconds RTC readout (Xen feature)
- generic support for Xen suspend/resume oddities
- the usual lot of fixes and cleanups all over the place
The parts which touch other areas (ARM/XEN) have been coordinated with
the relevant maintainers. Though this results in an handful of
trivial to solve merge conflicts, which we preferred over nasty cross
tree merge dependencies.
The patches which have been committed in the last few days are bug
fixes plus the posix timer lot. The latter was in akpms queue and
next for quite some time; they just got forgotten and Frederic
collected them last minute."
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
hrtimer: Remove unused variable
hrtimers: Move SMP function call to thread context
clocksource: Reselect clocksource when watchdog validated high-res capability
posix-cpu-timers: don't account cpu timer after stopped thread runtime accounting
posix_timers: fix racy timer delta caching on task exit
posix-timers: correctly get dying task time sample in posix_cpu_timer_schedule()
selftests: add basic posix timers selftests
posix_cpu_timers: consolidate expired timers check
posix_cpu_timers: consolidate timer list cleanups
posix_cpu_timer: consolidate expiry time type
tick: Sanitize broadcast control logic
tick: Prevent uncontrolled switch to oneshot mode
tick: Make oneshot broadcast robust vs. CPU offlining
x86: xen: Sync the CMOS RTC as well as the Xen wallclock
x86: xen: Sync the wallclock when the system time is set
timekeeping: Indicate that clock was set in the pvclock gtod notifier
timekeeping: Pass flags instead of multiple bools to timekeeping_update()
xen: Remove clock_was_set() call in the resume path
hrtimers: Support resuming with two or more CPUs online (but stopped)
timer: Fix jiffies wrap behavior of round_jiffies_common()
...
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
The x bit can easily get lost (patch(1) loses it, for example).
Reported-by: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the confusing naming indicates, this test has some overlap with
pre-existing tests. Would be nice to merge them eventually. But since it
is only test code, cleanliness is much less important than mere existence.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
thuge-gen was forgotten. Fix it by removing the duplication, so we don't
get too many repeats.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case this ever gets scripted, it should return 0 on success and 1 on
failure. Parsing the output should be left to meatbags.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add some initial basic tests on a few posix timers interface such as
setitimer() and timer_settime().
These simply check that expiration happens in a reasonable timeframe after
expected elapsed clock time (user time, user + system time, real time,
...).
This is helpful for finding basic breakages while hacking
on this subsystem.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: Olivier Langlois <olivier@trillion01.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The TPACKET_V3 test code consists of a lot of unecessary macro
wrappers that rather obfuscate what members are accessed in what
way. So get rid of them and make the code more readable. Also
credit Chetan for providing tpacket_v3 example code. Furthermore,
get rid of private offset usage, as we do not need it here.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert commit 58c7be84fe ("selftest: add simple test for soft-dirty
bit"). This is the self test for Pavel's pagemap2 patches which didn't
actually get merged.
Reported-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
* Dump signals from process-wide and per-thread queues with
different sizes of buffers.
* Check error paths for buffers with restricted permissions. A part of
buffer or a whole buffer is for read-only.
* Try to get nonexistent signal.
Signed-off-by: Andrew Vagin <avagin@openvz.org>
Cc: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Cc: "Michael Kerrisk (man-pages)" <mtk.manpages@gmail.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pedro Alves <palves@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It creates a mapping of 3 pages and checks that reads, writes and
clear-refs result in present and soft-dirt bits reported from pagemap2
set as expected.
[akpm@linux-foundation.org: alphasort the Makefile TARGETS to reduce rejects]
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
and has conflicts it the grub menus. That is, if the machines use
the same grub menu name, but they are at different locations in the
menu.lst file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJRfneBAAoJEOdOSU1xswtMB/EIAMBKvuyNDUch0ym5d/rKV0Vn
okmD8UM0aL/LKkhSHO1LlPusl+3nCF1cW9BNAEZ1b+orP/ipLL971s3tE1pJjfQU
mHo8HpfnxrCJweczjWX3XVqtG1WBwMqMOEs1Zfg6ybuN10hVHMwfd5CVWLmRg2mi
3sSaktQnYkFwjcujlbjVFNlenLu5pBXFFy1MdHIR9uZV4GIJM5kNL68+82T4VC6A
gQCm40KpyaHzNmsxnVxosKOD2vHOq/OdxLs/J39qvdEO2wZOMAH/YLYOCz+eq1WO
tD0cQ3P2IbrDFx7Wm25JMcmM+9GumClIwGF96Q+9WRhEyY3w0j7VNGtsdL1ktSw=
=98Xp
-----END PGP SIGNATURE-----
Merge tag 'ktest-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull ktest update from Steven Rostedt:
"A couple of fixes to handle a config file that tests multiple machines
and has conflicts it the grub menus. That is, if the machines use the
same grub menu name, but they are at different locations in the
menu.lst file"
* tag 'ktest-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Reset grub menu cache with different machines
ktest: Allow tests to use different GRUB_MENUs
Testing like this for TP_STATUS_AVAILABLE clearly is a stupid bug
since it always returns true. Fix this by only checking for flags
where the kernel owns the packet and negate this result, since we
also could run into the non-zero status TP_STATUS_WRONG_FORMAT
and need to reclaim frames.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different tests may use a different machine. In such cases, we need to
try to get the current grub menu index. If the same grub menu is used
for two different machines, it may not be at the same index on the
second machine. A search for the index must be performed again.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This patch adds a simple test case that probes the packet socket's
TPACKET_V1, TPACKET_V2 and TPACKET_V3 behavior regarding mmap(2)'ed
I/O for a small burst of 100 packets. The test currently runs for ...
TPACKET_V1: RX_RING, TX_RING
TPACKET_V2: RX_RING, TX_RING
TPACKET_V3: RX_RING
... and will output on success:
test: TPACKET_V1 with PACKET_RX_RING .................... 100 pkts (9600 bytes)
test: TPACKET_V1 with PACKET_TX_RING .................... 100 pkts (9600 bytes)
test: TPACKET_V2 with PACKET_RX_RING .................... 100 pkts (9600 bytes)
test: TPACKET_V2 with PACKET_TX_RING .................... 100 pkts (9600 bytes)
test: TPACKET_V3 with PACKET_RX_RING .................... 100 pkts (9600 bytes)
OK. All tests passed
Reusable parts of psock_fanout.c have been put into a psock_lib.h
file for common usage. Test case successfully tested on x86_64.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packetsocket fanout test uses a packet ring. Use TPACKET_V2
instead of TPACKET_V1 to work around a known 32/64 bit issue in
the older ring that manifests on sparc64.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix flaky results with PACKET_FANOUT_HASH depending on whether the
two flows hash into the same packet socket or not.
Also adds tests for PACKET_FANOUT_LB and PACKET_FANOUT_CPU and
replaces the counting method with a packet ring.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes:
v3->v2: rebase (no other changes)
passes selftest
v2->v1: read f->num_members only once
fix bug: test rollover mode + flag
Minimize packet drop in a fanout group. If one socket is full,
roll over packets to another from the group. Maintain flow
affinity during normal load using an rxhash fanout policy, while
dispersing unexpected traffic storms that hit a single cpu, such
as spoofed-source DoS flows. Rollover breaks affinity for flows
arriving at saturated sockets during those conditions.
The patch adds a fanout policy ROLLOVER that rotates between sockets,
filling each socket before moving to the next. It also adds a fanout
flag ROLLOVER. If passed along with any other fanout policy, the
primary policy is applied until the chosen socket is full. Then,
rollover selects another socket, to delay packet drop until the
entire system is saturated.
Probing sockets is not free. Selecting the last used socket, as
rollover does, is a greedy approach that maximizes chance of
success, at the cost of extreme load imbalance. In practice, with
sufficiently long queues to absorb bursts, sockets are drained in
parallel and load balance looks uniform in `top`.
To avoid contention, scales counters with number of sockets and
accesses them lockfree. Values are bounds checked to ensure
correctness.
Tested using an application with 9 threads pinned to CPUs, one socket
per thread and sufficient busywork per packet operation to limits each
thread to handling 32 Kpps. When sent 500 Kpps single UDP stream
packets, a FANOUT_CPU setup processes 32 Kpps in total without this
patch, 270 Kpps with the patch. Tested with read() and with a packet
ring (V1).
Also, passes psock_fanout.c unit test added to selftests.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To save connecting and searching for a given grub menu for each test,
ktest.pl will cache the grub number it found. The problem is that
different tests might use a different grub menu, but ktest.pl will
ignore it.
Instead, have ktest.pl check if the grub menu it used to cache the
content is the same as when it grabbed the menu. If not, grab it again,
otherwise just return the cached value.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Stricter validation was introduced with commit da27a24383
("efivarfs: guid part of filenames are case-insensitive") and commit
47f531e8ba ("efivarfs: Validate filenames much more aggressively"),
which is necessary for the guid portion of efivarfs filenames, but we
don't need to be so strict with the first part, the variable name. The
UEFI specification doesn't impose any constraints on variable names
other than they be a NULL-terminated string.
The above commits caused a regression that resulted in users seeing
the following message,
$ sudo mount -v /sys/firmware/efi/efivars mount: Cannot allocate memory
whenever pstore EFI variables were present in the variable store,
since their variable names failed to pass the following check,
/* GUID should be right after the first '-' */
if (s - 1 != strchr(str, '-'))
as a typical pstore filename is of the form, dump-type0-10-1-<guid>.
The fix is trivial since the guid portion of the filename is GUID_LEN
bytes, we can use (len - GUID_LEN) to ensure the '-' character is
where we expect it to be.
(The bogus ENOMEM error value will be fixed in a separate patch.)
Reported-by: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Joseph Yasi <joe.yasi@gmail.com>
Reported-by: Lingzhu Xiang <lxiang@redhat.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: <stable@vger.kernel.org> # v3.8
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
This change adds a little documentation to the tests under
tools/testing/selftests/, based on akpm's explanation.
[akpm@linux-foundation.org: move from Documentation to tools/testing/selftests/README.txt]
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do it one-per-line to reduce patch conflict pain.
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Test that reads from a newly-created efivarfs file (with no data written)
will return EOF.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Lingzhu Xiang <lxiang@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Lingzhu Xiang <lxiang@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change adds a few initial efivarfs tests to the
tools/testing/selftests directory.
The open-unlink test is based on code from Lingzhu Xiang.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Lingzhu Xiang <lxiang@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The index of a line where a warning is tested can be returned
differently on different versions of gcc (or same version compiled
differently). That is, a tab + space can give different results. This
causes the warning check to produce a false positive. Removing the
index from the check fixes this issue.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The reboot just wants to get to the next kernel. But if a warning (Call
Trace) appears, the monitor will report an error, and the reboot will
think something went wrong and power cycle the box, even though we
successfully made it to the next kernel.
Ignore warnings during the reboot until we get to the next kernel. It
will still timeout if we never get to the next kernel and then a power
cycle will happen. That's what we want it to do.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Sometimes when a test kernel passed fine, but on reboot it crashed,
ktest could get stuck and not proceed. This would be frustrating if you
let a test run overnight to find out the next morning that it was stuck
on the first test.
To fix this, I made reboot check for the REBOOT_SUCCESS_LINE. If the
line was not detected, then it would power cycle the box.
What it didn't cover was if the REBOOT_SUCCESS_LINE wasn't defined or if
a 'good' kernel did not display the line. Instead have it search for the
Linux banner "Linux version". The reboot just needs to get to the start
of the next kernel, it does not need to test if the next kernel makes it
to a boot prompt.
After we find the next kernel has booted, then we just wait for either
the REBOOT_SUCCESS_LINE to appear or the timeout.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Although the patchcheck test checks for warnings in the files that were
changed, this check does not catch warnings that were caused by header
file changes and the warnings appear in C files not touched by the
commit.
Add a new option called WARNINGS_FILE. If this option is set, then the
file it points to is read before bulid, and the file should contain a
list of known warnings. If a warning appears in the build, this file is
checked, and if the warning does not exist in this file, then it fails
the build showing the new warning.
If the WARNINGS_FILE points to a file that does not exist, this will
cause any warning in the build to fail.
A new test is also added called "make_warnings_file". This test will
create do a build and record any warnings it finds into the
WARNINGS_FILE. This test is something that can be run before other tests
to build a warnings file of "known warnings", ie, warnings that were
there before your changes.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Options are allowed to use other options, for example:
LOG_FILE = ${OUTPUT_DIR}/${MACHINE}.log
where the option LOG_FILE used the options OUTPUT_DIR and MACHINE.
But if a test option were to use a default option, it will not get
substituted:
OUTPUT_DIR = ${THIS_DIR}/${MACHINE}
TEST_START
OUTPUT_DIR = ${OUTPUT_DIR}/t1
For the above test, OUTPUT_DIR will stay literally "${OUTPUT_DIR}/t1"
and not be converted to "${THIS_DIR}/${MACHINE}/t1". When the test runs,
it will pass the ${OUTPUT_DIR} to the shell, which would probaly
interpret it as "", and the output directory will end up as "/t1".
Change the code where if a test option has its own option name in
its defined field, and a default option exists, then substitute the
default option in its place.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The patchcheck test looks at what files are modified for each patch it
checks and makes sure that those files do not produce any warnings.
Unfortunately, when it read the diffstat, the newlines were added on the
files and this made compares miss warnings, and commits that should not
have passed, ktest let pass.
Fix this by using the perl command "chomp" that strips off whitespace at
the end of lines.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If the user is doing a build or install bisect, there's no reason to
have them define CONSOLE, as the console does not need to be read. The
console only needs to be read for boot tests.
CONSOLE is not required for normal build or install tests, let's not
require it for bisect tests with BISECT_TYPE of build or install.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This test can be used to check wheither kernel supports IPC message queue
copy and restore features (required by CRIU project).
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I was curious why sys_kcmp wasn't working, which led me to the testcase.
It turned out I hadn't enabled CHECKPOINT_RESTORE in the kernel I was
testing. Add a decoding of errno to the testcase to make that obvious.
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case breakpoint test exit non zero value it will cause make error.
Better way is just print the test failure status.
Signed-off-by: Dave Young <dyoung@redhat.com>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case kcmp_test exit non zero value it will cause make error.
Better way is just print the test failure status.
Signed-off-by: Dave Young <dyoung@redhat.com>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
make run_tests need the target is run_tests instead of run-tests
Also gcc output should be kcmp_test. Fix these two issues.
Signed-off-by: Dave Young <dyoung@redhat.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Original behavior:
bash-4.1$ make -C mqueue run_tests
make: Entering directory `/home/dave/git/linux-2.6/tools/testing/selftests/mqueue'
./mq_open_tests /test1
Not running as root, but almost all tests require root in order to modify
system settings. Exiting.
make: *** [run_tests] Error 1
make: Leaving directory `/home/dave/git/linux-2.6/tools/testing/selftests/mqueue'
After applying the patch:
bash-4.1$ make -C mqueue run_tests
make: Entering directory `/home/dave/git/linux-2.6/tools/testing/selftests/mqueue'
Not running as root, but almost all tests require root in order to modify
system settings. Exiting.
mq_open_tests: [FAIL]
Not running as root, but almost all tests require root in order to modify
system settings. Exiting.
mq_perf_tests: [FAIL]
make: Leaving directory `/home/dave/git/linux-2.6/tools/testing/selftests/mqueue'
Signed-off-by: Dave Young <dyoung@redhat.com>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Original behavior:
bash-4.1$ make -C vm run_tests
make: Entering directory `/home/dave/git/linux-2.6/tools/testing/selftests/vm'
/bin/sh ./run_vmtests
./run_vmtests: line 24: /proc/sys/vm/nr_hugepages: Permission denied
Please run this test as root
make: *** [run_tests] Error 1
make: Leaving directory `/home/dave/git/linux-2.6/tools/testing/selftests/vm'
After applying the patch:
bash-4.1$ make -C vm run_tests
make: Entering directory `/home/dave/git/linux-2.6/tools/testing/selftests/vm'
./run_vmtests: line 24: /proc/sys/vm/nr_hugepages: Permission denied
Please run this test as root
vmtests: [FAIL]
make: Leaving directory `/home/dave/git/linux-2.6/tools/testing/selftests/vm'
Signed-off-by: Dave Young <dyoung@redhat.com>
Cc: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQyQEHAAoJEOdOSU1xswtMLPAH/0KmJ92GDwc7fJ2Q+H1Vfio2
nIqucSESNRvJ2m48cN39ZlXB3NLOEwIRxcD9ISkx+S9Jlvu4GlQmpd8P65n7u5Ll
7LnH+G/crKPo2uHPnT1FFi40zFiicY0SobtBxu8ouXoNL7M68hlbczvmUh/veBUh
rUmaUgio2K6/NUeYdztV15mEgpAuZ41NYp9OsO8g44AI+pWv9OigAVP/qN+1BFzJ
IK0rqZgooAzMgV7Px+y4uegjBuC5UQYbde5XcDQVNUc8gLudedSg2LPg2IOtl/cp
JsyePL2/7C8y5lfA9p1bVHUUD9VTdNoLJbUd8SiLeV7+TFl6xPVl8fBd2el3ZVI=
=kM0o
-----END PGP SIGNATURE-----
Merge tag 'ktest-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull ktest update from Steven Rostedt:
"fixes and updated for new boot loaders"
* tag 'ktest-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Test if target machine is up before install
ktest: Fix breakage from change of oldnoconfig to olddefconfig
ktest: Add native support for syslinux boot loader
ktest: Sync before reboot
ktest: Add support for grub2
Sometimes a test kernel will crash or hang on reboot (this is even more
apparent when testing a config without CGROUPS on a box running
systemd). When this happens, on the next iteration of installing a
kernel, ktest will fail when it tries to install.
Have ktest do a check to see if the target can be connected to via ssh
before it tries to install. If it can't connect, then reboot again.
This time the reboot will fail because it can't connect and will force a
power cycle.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Commit fb16d891 "kconfig: replace 'oldnoconfig' with 'olddefconfig', and
keep the old name", changed ktest's default config update from
oldnoconfig to olddefconfig without adding oldnoconfig as a backup.
The make oldnoconfig works much better than its backup of:
yes '' | make oldconfig
But due to this change, and the fact that ktest is used to build lots of
older kernels (and for bisects), it forgoes the oldnoconfig completely.
Cc: Adam Lee <adam8157@gmail.com>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
I installed Fedora 17 which no longer supports grub v1. I worked
with grub2 for a while, but there's so many issues with it and automated
rebooting, that I decided to switch to syslinux. Instead of using
the REBOOT_SCRIPT and add customized changes to get syslinux booted,
I thought it better to make ktest aware of syslinux and add options
to simplify the use of syslinux on a target test box.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: John 'Warthog9' Hawley <warthog9@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Before rebooting the target, run the sync command, as it seems that
either Grub2 or systemd gets screwed up if you update to reboot a kernel
once and do a reboot without doing a sync.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
As only grub or 'script' is supported for rebooting to a new kernel,
and Fedora 17 has dropped support for grub, I decided to add grub2
support as well (I also plan on adding syslinux/extlinux support too).
The options GRUB_FILE and GRUB_REBOOT were added to allow the user
to specify where to find the grub.cfg and what tool to use to reboot
into the next kernel respectively.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Revert commit 03a7beb55b ("epoll: support for disabling items, and a
self-test app") pending resolution of the issues identified by Michael
Kerrisk, copied below.
We'll revisit this for 3.8.
: I've taken a look at this patch as it currently stands in 3.7-rc1, and
: done a bit of testing. (By the way, the test program
: tools/testing/selftests/epoll/test_epoll.c does not compile...)
:
: There are one or two places where the behavior seems a little strange,
: so I have a question or two at the end of this mail. But other than
: that, I want to check my understanding so that the interface can be
: correctly documented.
:
: Just to go though my understanding, the problem is the following
: scenario in a multithreaded application:
:
: 1. Multiple threads are performing epoll_wait() operations,
: and maintaining a user-space cache that contains information
: corresponding to each file descriptor being monitored by
: epoll_wait().
:
: 2. At some point, a thread wants to delete (EPOLL_CTL_DEL)
: a file descriptor from the epoll interest list, and
: delete the corresponding record from the user-space cache.
:
: 3. The problem with (2) is that some other thread may have
: previously done an epoll_wait() that retrieved information
: about the fd in question, and may be in the middle of using
: information in the cache that relates to that fd. Thus,
: there is a potential race.
:
: 4. The race can't solved purely in user space, because doing
: so would require applying a mutex across the epoll_wait()
: call, which would of course blow thread concurrency.
:
: Right?
:
: Your solution is the EPOLL_CTL_DISABLE operation. I want to
: confirm my understanding about how to use this flag, since
: the description that has accompanied the patches so far
: has been a bit sparse
:
: 0. In the scenario you're concerned about, deleting a file
: descriptor means (safely) doing the following:
: (a) Deleting the file descriptor from the epoll interest list
: using EPOLL_CTL_DEL
: (b) Deleting the corresponding record in the user-space cache
:
: 1. It's only meaningful to use this EPOLL_CTL_DISABLE in
: conjunction with EPOLLONESHOT.
:
: 2. Using EPOLL_CTL_DISABLE without using EPOLLONESHOT in
: conjunction is a logical error.
:
: 3. The correct way to code multithreaded applications using
: EPOLL_CTL_DISABLE and EPOLLONESHOT is as follows:
:
: a. All EPOLL_CTL_ADD and EPOLL_CTL_MOD operations should
: should EPOLLONESHOT.
:
: b. When a thread wants to delete a file descriptor, it
: should do the following:
:
: [1] Call epoll_ctl(EPOLL_CTL_DISABLE)
: [2] If the return status from epoll_ctl(EPOLL_CTL_DISABLE)
: was zero, then the file descriptor can be safely
: deleted by the thread that made this call.
: [3] If the epoll_ctl(EPOLL_CTL_DISABLE) fails with EBUSY,
: then the descriptor is in use. In this case, the calling
: thread should set a flag in the user-space cache to
: indicate that the thread that is using the descriptor
: should perform the deletion operation.
:
: Is all of the above correct?
:
: The implementation depends on checking on whether
: (events & ~EP_PRIVATE_BITS) == 0
: This replies on the fact that EPOLL_CTL_AD and EPOLL_CTL_MOD always
: set EPOLLHUP and EPOLLERR in the 'events' mask, and EPOLLONESHOT
: causes those flags (as well as all others in ~EP_PRIVATE_BITS) to be
: cleared.
:
: A corollary to the previous paragraph is that using EPOLL_CTL_DISABLE
: is only useful in conjunction with EPOLLONESHOT. However, as things
: stand, one can use EPOLL_CTL_DISABLE on a file descriptor that does
: not have EPOLLONESHOT set in 'events' This results in the following
: (slightly surprising) behavior:
:
: (a) The first call to epoll_ctl(EPOLL_CTL_DISABLE) returns 0
: (the indicator that the file descriptor can be safely deleted).
: (b) The next call to epoll_ctl(EPOLL_CTL_DISABLE) fails with EBUSY.
:
: This doesn't seem particularly useful, and in fact is probably an
: indication that the user made a logic error: they should only be using
: epoll_ctl(EPOLL_CTL_DISABLE) on a file descriptor for which
: EPOLLONESHOT was set in 'events'. If that is correct, then would it
: not make sense to return an error to user space for this case?
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: "Paton J. Lewis" <palewis@adobe.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
were not being brought up. I found that the modules for the
network was not being installed. This was due to the config
CONFIG_MODULES_USE_ELF_RELA that came before CONFIG_MODULES, and
confused ktest in thinking that CONFIG_MODULES=y was not found.
Ktest needs to test all configs and not just stop if something starts
with CONFIG_MODULES.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQig8hAAoJEOdOSU1xswtMkFgIALLcnba79RHsPdGCTX247Hcg
UdteytZgyd1XayDSPLOVAR5f1vJeZ/6/L5dwWqZpf+j6wUTBwdUTc4DlBwHNpi8V
XDKbwAYWAQp4BVaQkKcrxKZZepE791NWxCelG7T7S0d7jIkwFTA4BhT4+8+QFztZ
H5IDL+HA73Jvehfv3gpJW6yDQ/QSyUjIK4QCsJS+wodB9nDzhAEiZ6ZKflSXFGq4
J+Fl/UfRfnA+j0aP75ecL7hewfdiLOmK67vKvW3l8wZ7s0y3NnIsxymmaa6sTIAQ
lIAsmSPdqOzXExIKLBHnsHCog6UW4a91MmEqM05IDpt+AcCnwDbk4EfbJEXa8ug=
=vl1t
-----END PGP SIGNATURE-----
Merge tag 'ktest-v3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull ktest confusion fix from Steven Rostedt:
"With the v3.7-rc2 kernel, the network cards on my target boxes were
not being brought up.
I found that the modules for the network was not being installed.
This was due to the config CONFIG_MODULES_USE_ELF_RELA that came
before CONFIG_MODULES, and confused ktest in thinking that
CONFIG_MODULES=y was not found.
Ktest needs to test all configs and not just stop if something starts
with CONFIG_MODULES."
* tag 'ktest-v3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Fix ktest confusion with CONFIG_MODULES_USE_ELF_RELA
In order to decide if ktest should bother installing modules on the
target box, it checks if the config file has CONFIG_MODULES=y. But it
also checks if the '=y' part exists. It only will install modules if the
config exists and is set with '=y'. But as the regex that was used
tests:
/^CONFIG_MODULES(=y)?/
this will also match:
CONFIG_MODULES_USE_ELF_RELA
as the '=y' part was optional and it did not test the rest of the line.
When this happens, ktest will stop checking the rest of the configs but
it will also think that no modules are needed to be installed. What it
should do is only jump out of the loop if it actually found a
CONFIG_MODULES that is set to true.
Otherwise, ktest wont install the necessary modules needed for proper
booting of the test target.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Latest Linus head run of "make selftests" in the tools directory failed
with references to undefined variables. Reference was to
'write_thread_data' which is the name of a struct that is being used, not
the variable itself. Change reference so it points to the variable.
Signed-off-by: Daniel Hazelton <dshadowwolf@gmail.com>
Cc: "Paton J. Lewis" <palewis@adobe.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull kconfig changes from Michal Marek:
"kconfig in v3.7 is going to
- initialize ncurses only once in menuconfig
- be able to jump to a search result in menuconfig
- change the misnomer oldnoconfig to a more meaningful name
olddefconfig, keeping the old name as alias"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: replace 'oldnoconfig' with 'olddefconfig', and keep the old name as an alias
menuconfig: Assign jump keys per-page instead of globally
menuconfig: Do not open code textbox scroll up/down
menuconfig: Add jump keys to search results
menuconfig: Extend dialog_textbox so that it can return to a scrolled position
menuconfig: Extend dialog_textbox so that it can exit on arbitrary keypresses
menuconfig: Remove superfluous conditionnal
kconfig: document oldnoconfig to what it really does in conf.c
kconfig/mconf.c: revision of curses initialization.
Enhanced epoll_ctl to support EPOLL_CTL_DISABLE, which disables an epoll
item. If epoll_ctl doesn't return -EBUSY in this case, it is then safe to
delete the epoll item in a multi-threaded environment. Also added a new
test_epoll self- test app to both demonstrate the need for this feature
and test it.
Signed-off-by: Paton J. Lewis <palewis@adobe.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Paul Holland <pholland@adobe.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix parsing of ELSE IF in reading config file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQaZ0mAAoJEOdOSU1xswtMVzsIAIXFrMbOkDyo3brW0IVv3z1x
EnZ6NPzIoEnQbAsiLT52tFJH3+C+c7vjKrEQx8OxsDaElv+pAuR9TOPJlxoGBd21
wzQNXtdxDcGQKgWvOn/9ebkBAFe4GnWSWZc+LykI8QioQAitSIJfTu38a4Dyu2pG
KZqpd+LHDeE+N5jg/tmT3sVCYOmR6Oui9rzqkhkVoGNlNZ6Q3ndPAAcv6A4lf7z8
4UOAp/B8f6wbJblMPCjwcle1rMk6gfQ7Kcbli/Xm7U7cBwNhv/HJwWk9Zh/LrUjM
3RVWJ1mXNVp0cTTKfAHrAWEWgm+vJtIkItnSWkkJnU3qwYltE0vs/CwIHOkeAFc=
=lE0h
-----END PGP SIGNATURE-----
Merge tag 'ktest-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull ktest fix from Steven Rostedt:
"ktest has one fix needed for this merge window - fix parsing of ELSE
IF in reading config file"
* tag 'ktest-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Fix ELSE IF statements
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
As 67d34a6a39 said, 'oldnoconfig' doesn't
set new symbols to 'n', but instead sets it to their default values.
So, this patch replaces 'oldnoconfig' with 'olddefconfig', stop making
people confused, and keep the old name 'oldnoconfig' as an alias,
because people already are dependent on its behavior with the
counter-intuitive name.
Signed-off-by: Adam Lee <adam8157@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
The ELSE IF statements do not work as expected if another ELSE statement
follows. This is because the $if_set is not set. If the ELSE IF
condition is true, the following ELSE should be ignored. But because the
$if_set is not set, the following ELSE will also be executed.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
"fault-injection: add tool to run command with failslab or
fail_page_alloc" added tools/testing/fault-injection/failcmd.sh to make it
easier to inject slab/page allocation failures by fault injection.
failcmd.sh prints the following warning when running with arguments
for command.
# ./failcmd.sh echo aaa
failcmd.sh: line 209: [: echo: binary operator expected
aaa
This warning is caused by an improper check whether at least one
parameter is left after parsing command options.
Fix it by testing the length of $1 instead of $@
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge Andrew's first set of patches:
"Non-MM patches:
- lots of misc bits
- tree-wide have_clk() cleanups
- quite a lot of printk tweaks. I draw your attention to "printk:
convert the format for KERN_<LEVEL> to a 2 byte pattern" which
looks a bit scary. But afaict it's solid.
- backlight updates
- lib/ feature work (notably the addition and use of memweight())
- checkpatch updates
- rtc updates
- nilfs updates
- fatfs updates (partial, still waiting for acks)
- kdump, proc, fork, IPC, sysctl, taskstats, pps, etc
- new fault-injection feature work"
* Merge emailed patches from Andrew Morton <akpm@linux-foundation.org>: (128 commits)
drivers/misc/lkdtm.c: fix missing allocation failure check
lib/scatterlist: do not re-write gfp_flags in __sg_alloc_table()
fault-injection: add tool to run command with failslab or fail_page_alloc
fault-injection: add selftests for cpu and memory hotplug
powerpc: pSeries reconfig notifier error injection module
memory: memory notifier error injection module
PM: PM notifier error injection module
cpu: rewrite cpu-notifier-error-inject module
fault-injection: notifier error injection
c/r: fcntl: add F_GETOWNER_UIDS option
resource: make sure requested range is included in the root range
include/linux/aio.h: cpp->C conversions
fs: cachefiles: add support for large files in filesystem caching
pps: return PTR_ERR on error in device_create
taskstats: check nla_reserve() return
sysctl: suppress kmemleak messages
ipc: use Kconfig options for __ARCH_WANT_[COMPAT_]IPC_PARSE_VERSION
ipc: compat: use signed size_t types for msgsnd and msgrcv
ipc: allow compat IPC version field parsing if !ARCH_WANT_OLD_COMPAT_IPC
ipc: add COMPAT_SHMLBA support
...
This adds tools/testing/fault-injection/failcmd.sh to run a command while
injecting slab/page allocation failures via fault injection.
Example:
Run a command "make -C tools/testing/selftests/ run_tests" with
injecting slab allocation failure.
# ./tools/testing/fault-injection/failcmd.sh \
-- make -C tools/testing/selftests/ run_tests
Same as above except to specify 100 times failures at most instead of
one time at most by default.
# ./tools/testing/fault-injection/failcmd.sh --times=100 \
-- make -C tools/testing/selftests/ run_tests
Same as above except to inject page allocation failure instead of slab
allocation failure.
# env FAILCMD_TYPE=fail_page_alloc \
./tools/testing/fault-injection/failcmd.sh --times=100 \
-- make -C tools/testing/selftests/ run_tests
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds two selftests
* tools/testing/selftests/cpu-hotplug/on-off-test.sh is testing script
for CPU hotplug
1. Online all hot-pluggable CPUs
2. Offline all hot-pluggable CPUs
3. Online all hot-pluggable CPUs again
4. Exit if cpu-notifier-error-inject.ko is not available
5. Offline all hot-pluggable CPUs in preparation for testing
6. Test CPU hot-add error handling by injecting notifier errors
7. Online all hot-pluggable CPUs in preparation for testing
8. Test CPU hot-remove error handling by injecting notifier errors
* tools/testing/selftests/memory-hotplug/on-off-test.sh is doing the
similar thing for memory hotplug.
1. Online all hot-pluggable memory
2. Offline 10% of hot-pluggable memory
3. Online all hot-pluggable memory again
4. Exit if memory-notifier-error-inject.ko is not available
5. Offline 10% of hot-pluggable memory in preparation for testing
6. Test memory hot-add error handling by injecting notifier errors
7. Online all hot-pluggable memory in preparation for testing
8. Test memory hot-remove error handling by injecting notifier errors
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add '=~' and '!~' to the list of allowed conditionals for DEFAULT and
TEST_START section if statements.
ie.
TEST_START IF TEST =~ .*test$
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The option IGNORE_ERRORS is used to allow a test to succeed even if a
warning appears from the kernel. Sometimes kernels will produce warnings
that are not associated with a test, and the user wants to test
something else.
The IGNORE_ERRORS works for boot up, but was not preventing test runs to
succeed if the kernel produced a warning.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The min configs are saved in a perl hash called force_configs, and this
hash is used to add configs to the .config file. But it was not being
reset between tests and a min config from a previous test would affect
the min config of the next test causing undesirable results.
Reset the force_config hash at the start of each test.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Usually the target is booted into a dependable kernel when a test
starts. The test will install the test kernel and reboot the box. But
there may be a time that the kernel is running an unreliable kernel and
the reboot may crash.
Have ktest detect crashes on a reboot and force a power-cycle instead.
This can usually happen if a test kernel was installed to run manual
tests, but the user forgot to reboot to the known good kernel.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If the console is constantly outputting content, this can cause ktest
to get stuck waiting on the monitor to settle down.
The option MAX_MONITOR_WAIT is the maximum time (in seconds) for ktest
to wait for the console to flush.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
With a name like 'oldnoconfig' one may think that the config generated
would disable all configs that were not defined (selecting "no" for all
options). But this is not the case. It selects the default. If a config
has a 'default y', then it is added if not specified.
This broke the config bisect, because options not specified by a config
will just use the default, where it expected to turn off. This caused an
option to be enabled that disabled an option that would break the build.
The end result was that we never found the bad config at the end of the
test.
Instead of using 'make oldnoconfig', ktest now builds the options it
expects enabled and disabled. When it turns off an option, it will no
longer remove it, but actually set it to:
# CONFIG_FOO is not set.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The config-bisect can take a bad config and bisect it down to find out
what config actually breaks the config. But as all tests will apply a
minconfig (defined by a user) to apply before booting, it is possible
that the minconfig could actually make the bad config work (minconfigs
can disable configs). The end result is that the config bisect test will
not find a config that breaks. This can be rather frustrating to the
user.
The CONFIG_BISECT_CHECK option, when set to 1, will make sure that the
bad config (with the minconfig applied) still fails before trying to
bisect.
And yes, I did get burned by this.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add the PRE_INSTALL option that will allow a user to specify a shell
command to be executed before the install operation executes.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
In order to let the user add commands before and after ktest runs, the
PRE_KTEST and POST_KTEST options are defined. They hold shell commands
that will execute befor ktest runs its first test, as well as when it
completed its last test.
The PRE_TEST and POST_TEST will be run befor and after (respectively)
for a given test. They can either be global (done for all tests) or
defined by a single test.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
While doing the checkpoint-restore in the user space one need to determine
whether various kernel objects (like mm_struct-s of file_struct-s) are
shared between tasks and restore this state.
The 2nd step can be solved by using appropriate CLONE_ flags and the
unshare syscall, while there's currently no ways for solving the 1st one.
One of the ways for checking whether two tasks share e.g. mm_struct is to
provide some mm_struct ID of a task to its proc file, but showing such
info considered to be not that good for security reasons.
Thus after some debates we end up in conclusion that using that named
'comparison' syscall might be the best candidate. So here is it --
__NR_kcmp.
It takes up to 5 arguments - the pids of the two tasks (which
characteristics should be compared), the comparison type and (in case of
comparison of files) two file descriptors.
Lookups for pids are done in the caller's PID namespace only.
At moment only x86 is supported and tested.
[akpm@linux-foundation.org: fix up selftests, warnings]
[akpm@linux-foundation.org: include errno.h]
[akpm@linux-foundation.org: tweak comment text]
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Andrey Vagin <avagin@openvz.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Valdis.Kletnieks@vt.edu
Cc: Michal Marek <mmarek@suse.cz>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the mq_perf_tests tool I used when creating my mq performance patch.
Also add a local .gitignore to keep the binaries from showing up in git
status output.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Doug Ledford <dledford@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a directory to house POSIX message queue subsystem specific tests.
Add first test which checks the operation of mq_open() under various
corner conditions.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Joe Korty <joe.korty@ccur.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: Serge E. Hallyn <serue@us.ibm.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a README that explains what the different example configs in the
ktest example directory are about.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
I used the snowball.conf in a live demo that demonstrated how to use
ktest.pl with a snowball ARM board. I've been asked to included that
config in the ktest repository.
Here it is.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add the config that I use to test several archs. I downloaded several
cross compilers from:
http://kernel.org/pub/tools/crosstool/files/bin/x86_64/
and this config is an example to crosscompile several archs to make sure
that your changes do not break archs that you are not working on.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
I've been asked several times to provide more useful example configs for
ktest.pl, as the sample.conf is too complex (because it explains all
configs). This adds configs broken up by use case, and these configs are
based on actual configs that I use on a daily basis.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If the file that OUTPUT_MIN_CONFIG exists then ktest.pl will prompt the
user and ask them if the OUTPUT_MIN_CONFIG should be used as the
starting point for make_min_config instead of MIN_CONFIG.
This is usually the case, and to allow the user to do so, which is
helpful if the user is creating different min configs based on tests,
and they know one is a superset of another test, they can set
USE_OUTPUT_MIN_CONFIG to one, which will prevent kest.pl from prompting
to use the OUTPUT_MIN_CONFIG and it will just use it.
If USE_OUTPUT_MIN_CONIFG is set to zero, then ktest.pl will continue to
use MIN_CONFIG instead.
The default is that USE_OUTPUT_MIN_CONFIG is undefined.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add a MIN_CONFIG_TYPE that can be set to 'test' or 'boot'. The default
is 'boot' which is what make_min_config has done previously: makes a
config file that is the minimum needed to boot the target.
But when MIN_CONFIG_TYPE is set to 'test', not only must the target
boot, but it must also successfully run the TEST. This allows the
creation of a config file that is the minimum to boot and also
perform ssh to the target, or anything else a developer wants.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The PRE_BUILD and POST_BUILD options of ktest are added to allow the
user to add temporary patch to the system and remove it on builds. This
is sometimes use to take a change from another git branch and add it to
a series without the fix so that this series can be tested, when an
unrelated bug exists in the series.
The problem comes when a tagged commit is being used. For example, if
v3.2 is being tested, and we add a patch to it, the kernelrelease for
that commit will be 3.2.0+, but without the patch the version will be
3.2.0. This can cause problems when the kernelrelease is determined for
creating the /lib/modules directory. The kernel booting has the '+' but
the module directory will not, and the modules will be missing for that
boot, and may not allow the kernel to succeed.
The fix is to put the creation of the kernelrelease in the POST_BUILD
logic, before it applies the POST_BUILD operation. The POST_BUILD is
where the patch may be removed, removing the '+' from the kernelrelease.
The calculation of the kernelrelease will also stay in its current
location but will be ignored if it was already calculated previously.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The change to let individual tests decide to reboot the machine on
success of the entire test also prevented errors from rebooting
when an error was detected.
The "no_reboot" variable was only cleared if the test had
reboot_on_success set. But the no_reboot variable also prevents the test
rebooting when an error was detected even when REBOOT_ON_ERROR was set.
Add a new "reboot_success" variable that is used to determine if the
test should reboot on success and not touch the no_reboot variable.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When BISECT_REVERSE and BISECT_SKIP are used together with boot or test
testing, build failures are treated as boot or test failures and
'git bisect bad' is executed instead of 'git bisect skip'. This is because
the $ret value of -1 is treated as a build failure, but the $reverse_bisect
logic does not properly handle this.
Simple fix, only invert it if it is positive.
Link: http://lkml.kernel.org/r/1335235380-8509-1-git-send-email-Russ.Dill@ti.com
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
hugepage-mmap.c, hugepage-shm.c and map_hugetlb.c in Documentation/vm are
simple pass/fail tests, It's better to promote them to
tools/testing/selftests.
Thanks suggestion of Andrew Morton about this. They all need firstly
setting up proper nr_hugepages and hugepage-mmap need to mount hugetlbfs.
So I add a shell script run_vmtests to do such work which will call the
three test programs and check the return value of them.
Changes to original code including below:
a. add run_vmtests script
b. return error when read_bytes mismatch with writed bytes.
c. coding style fixes: do not use assignment in if condition
[akpm@linux-foundation.org: build the targets before trying to execute them]
[akpm@linux-foundation.org: Documentation/vm/ no longer has a Makefile. Fixes "make clean"]
Signed-off-by: Dave Young <dyoung@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
So a "make run_tests" will build the tests before trying to run them.
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the run_tests script and launch the selftests by calling "make
run_tests" from the selftests top directory instead. This delegates to
the Makefile in each selftest directory, where it is decided how to launch
the local test.
This removes the need to add each selftest directory to the now removed
"run_tests" top script.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2NU4
-----END PGP SIGNATURE-----
Merge tag 'ktest-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull ktest changes from Steven Rostedt.
* tag 'ktest-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Allow a test to override REBOOT_ON_SUCCESS
ktest: Fix SWITCH_TO_GOOD to also reboot the machine
ktest: Add SCP_TO_TARGET_INSTALL option
ktest: Add warning when bugs are ignored
ktest: Add INSTALL_MOD_STRIP=1 when installing modules
The option REBOOT_ON_SUCCESS is global, and will have the machine reboot
the the box if all tests are successful. But a test may not want the
machine to reboot, and perhaps have the kernel it loaded be used to
install the next kernel. Or the last test may set up a kernel that the
user may want to look at. In this case, the user could have the global
option REBOOT_ON_SUCCESS be true, but if a test is defined to run at the
end, that test can override the global option and keep the kernel it
installed for the user to log in with.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When the option SWITCH_TO_GOOD is set, it will be called when the system
needs to reboot to the good server. But currently, this keeps the reboot
from happening. The SWITCH_TO_GOOD is just a way to get to a new kernel,
it may not mean to not reboot.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Currently the option used to scp both the modules to the target as well
as the kernel image are the same (SCP_TO_TARGET). But some embedded
boards may require them to be different. The modules may need to be put
directly on the board, but the kernel image may need to go to a
tftpserver.
Add the option SCP_TO_TARGET_INSTALL that will allow the user to change
the config so that they may have the modules and image got to different
machines.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When IGNORE_ERRORS is set, ktest will not fail a test if a backtrace
is detected. But this can be an issue if the user added it in the
config but forgot to remove it. They may be left wondering why their
test did not fail, or even worse, why their bisect gave the wrong
commit.
Add a warning in the output if IGNORE_WARNINGS is set, and ktest detects
a kernel error.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Pull trivial tree from Jiri Kosina:
"It's indeed trivial -- mostly documentation updates and a bunch of
typo fixes from Masanari.
There are also several linux/version.h include removals from Jesper."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits)
kcore: fix spelling in read_kcore() comment
constify struct pci_dev * in obvious cases
Revert "char: Fix typo in viotape.c"
init: fix wording error in mm_init comment
usb: gadget: Kconfig: fix typo for 'different'
Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c"
writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header
writeback: fix typo in the writeback_control comment
Documentation: Fix multiple typo in Documentation
tpm_tis: fix tis_lock with respect to RCU
Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c"
Doc: Update numastat.txt
qla4xxx: Add missing spaces to error messages
compiler.h: Fix typo
security: struct security_operations kerneldoc fix
Documentation: broken URL in libata.tmpl
Documentation: broken URL in filesystems.tmpl
mtd: simplify return logic in do_map_probe()
mm: fix comment typo of truncate_inode_pages_range
power: bq27x00: Fix typos in comment
...
make_min_config test failed to work because the snowball board I was tesing
it against had a config that would not build. But the make_min_config
only tested the testing part and ignored build failures. The end result
was a config file that would not boot.
This time, for real.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wlL8
-----END PGP SIGNATURE-----
Merge tag 'ktest-fix-make-min-failed-build-for-real' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
While demoing ktest at ELC in 2012, it was embarrassing that the
make_min_config test failed to work because the snowball board I was
testing it against had a config that would not build. But the
make_min_config only tested the testing part and ignored build failures.
The end result was a config file that would not boot.
This time, for real.
* tag 'ktest-fix-make-min-failed-build-for-real' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Fix make_min_config test when build fails