The xilinx_emaclite uses __raw_writel and __raw_readl for register
accesses. Those functions do not imply any kind of memory barriers and
they may be reordered.
The driver does not seem to take that into account, though, and the
driver does not satisfy the ordering requirements of the hardware.
For clear examples, see xemaclite_mdio_write() and xemaclite_mdio_read()
which try to set MDIO address before initiating the transaction.
I'm seeing system freezes with the driver with GCC 5.4 and current
Linux kernels on Zynq-7000 SoC immediately when trying to use the
interface.
In commit 123c1407af ("net: emaclite: Do not use microblaze and ppc
IO functions") the driver was switched from non-generic
in_be32/out_be32 (memory barriers, big endian) to
__raw_readl/__raw_writel (no memory barriers, native endian), so
apparently the device follows system endianness and the driver was
originally written with the assumption of memory barriers.
Rather than try to hunt for each case of missing barrier, just switch
the driver to use iowrite32/ioread32/iowrite32be/ioread32be depending
on endianness instead.
Tested on little-endian Zynq-7000 ARM SoC FPGA.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: 123c1407af ("net: emaclite: Do not use microblaze and ppc IO
functions")
Signed-off-by: David S. Miller <davem@davemloft.net>
xilinx_emaclite looks at the received data to try to determine the
Ethernet packet length but does not properly clamp it if
proto_type == ETH_P_IP or 1500 < proto_type <= 1518, causing a buffer
overflow and a panic via skb_panic() as the length exceeds the allocated
skb size.
Fix those cases.
Also add an additional unconditional check with WARN_ON() at the end.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: bb81b2ddfa ("net: add Xilinx emac lite device driver")
Signed-off-by: David S. Miller <davem@davemloft.net>
100% reproducible issue found on SKL SkullCanyon NUC with two external
DP daisy-chained monitors in DP/MST mode. When turning off or changing
the input of the second monitor the machine stops with a kernel
oops. This issue happened with 4.8.8 as well as drm/drm-intel-nightly.
This issue is traced to an inconsistent control flow in
drm_dp_update_payload_part1(): the 'port' pointer is set to NULL at the
same time as 'req_payload.num_slots' is set to zero, but the pointer is
dereferenced even when req_payload.num_slot is zero.
The problematic dereference was introduced in commit dfda0df34
("drm/mst: rework payload table allocation to conform better") and may
impact all versions since v3.18
The fix suggested by Chris Wilson removes the kernel oops and was found to
work well after 10mn of monkey-testing with the second monitor power and
input buttons
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98990
Fixes: dfda0df342 ("drm/mst: rework payload table allocation to conform better.")
Cc: Dave Airlie <airlied@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Nathan D Ciobanu <nathan.d.ciobanu@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: <stable@vger.kernel.org> # v3.18+
Tested-by: Nathan D Ciobanu <nathan.d.ciobanu@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487076561-2169-1-git-send-email-jani.nikula@intel.com
There is a potential race between fuse_dev_do_write()
and request_wait_answer() contexts as shown below:
TASK 1:
__fuse_request_send():
|--spin_lock(&fiq->waitq.lock);
|--queue_request();
|--spin_unlock(&fiq->waitq.lock);
|--request_wait_answer():
|--if (test_bit(FR_SENT, &req->flags))
<gets pre-empted after it is validated true>
TASK 2:
fuse_dev_do_write():
|--clears bit FR_SENT,
|--request_end():
|--sets bit FR_FINISHED
|--spin_lock(&fiq->waitq.lock);
|--list_del_init(&req->intr_entry);
|--spin_unlock(&fiq->waitq.lock);
|--fuse_put_request();
|--queue_interrupt();
<request gets queued to interrupts list>
|--wake_up_locked(&fiq->waitq);
|--wait_event_freezable();
<as FR_FINISHED is set, it returns and then
the caller frees this request>
Now, the next fuse_dev_do_read(), see interrupts list is not empty
and then calls fuse_read_interrupt() which tries to access the request
which is already free'd and gets the below crash:
[11432.401266] Unable to handle kernel paging request at virtual address
6b6b6b6b6b6b6b6b
...
[11432.418518] Kernel BUG at ffffff80083720e0
[11432.456168] PC is at __list_del_entry+0x6c/0xc4
[11432.463573] LR is at fuse_dev_do_read+0x1ac/0x474
...
[11432.679999] [<ffffff80083720e0>] __list_del_entry+0x6c/0xc4
[11432.687794] [<ffffff80082c65e0>] fuse_dev_do_read+0x1ac/0x474
[11432.693180] [<ffffff80082c6b14>] fuse_dev_read+0x6c/0x78
[11432.699082] [<ffffff80081d5638>] __vfs_read+0xc0/0xe8
[11432.704459] [<ffffff80081d5efc>] vfs_read+0x90/0x108
[11432.709406] [<ffffff80081d67f0>] SyS_read+0x58/0x94
As FR_FINISHED bit is set before deleting the intr_entry with input
queue lock in request completion path, do the testing of this flag and
queueing atomically with the same lock in queue_interrupt().
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: fd22d62ed0 ("fuse: no fc->lock for iqueue parts")
Cc: <stable@vger.kernel.org> # 4.2+
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_rcv_established() can now run in process context.
We need to disable BH while acquiring tcp probe spinlock,
or risk a deadlock.
Fixes: 5413d1babe ("net: do not block BH while processing socket backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ricardo Nabinger Sanchez <rnsanchez@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of <linux/libc-compat.h> interface limitations, <netinet/in.h>
provided by libc cannot be included after <linux/in.h>, therefore any
header that includes <netinet/in.h> cannot be included after <linux/in.h>.
Change uapi/linux/l2tp.h, the last uapi header that includes
<netinet/in.h>, to include <linux/in.h> and <linux/in6.h> instead of
<netinet/in.h> and use __SOCK_SIZE__ instead of sizeof(struct sockaddr)
the same way as uapi/linux/in.h does, to fix linux/if_pppol2tp.h userspace
compilation errors like this:
In file included from /usr/include/linux/l2tp.h:12:0,
from /usr/include/linux/if_pppol2tp.h:21,
/usr/include/netinet/in.h:31:8: error: redefinition of 'struct in_addr'
Fixes: 47c3e7783b ("net: l2tp: deprecate PPPOL2TP_MSG_* in favour of L2TP_MSG_*")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 63d0f0a695.
It caused a regression on platforms where I2C controller is synthesized
with dynamic TAR update disabled. Detection code is testing is bit
DW_IC_CON_10BITADDR_MASTER in register DW_IC_CON read-only but fails to
restore original value in case bit is read-write.
Instead of fixing this we revert the commit since it was preparation for
the commit 0317e6c0f1 ("i2c: designware: do not disable adapter after
transfer") which was also reverted.
Reported-by: Shah Nehal-Bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Reported-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-By: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: <stable@vger.kernel.org> # v4.9+
Fixes: 63d0f0a695 ("i2c: designware: detect when dynamic tar update is possible")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reported as a Kaffeine bug:
https://bugs.kde.org/show_bug.cgi?id=375811
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
On Kernel 4.9, the default is to not accept DMA on stack anymore
on x86 architecture. On other architectures, this has been a
requirement since Kernel 2.2. So, after this patch, this driver
should likely work fine on all archs.
Tested with USB ID 2040:5510: Hauppauge Windham
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Multiple threads can call fanout_add() at the same time.
We need to grab fanout_mutex earlier to avoid races that could
lead to one thread freeing po->rollover that was set by another thread.
Do the same in fanout_release(), for peace of mind, and to help us
finding lockdep issues earlier.
Fixes: dc99f60069 ("packet: Add fanout support.")
Fixes: 0648ab70af ("packet: rollover prepare: per-socket state")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current driver, the MTU is set to the maximum value
capable for the backing device. This decision turned out to
be a mistake as it led to confusion among users. The expected
initial MTU value used for other IBM vNIC capable operating
systems is 1500, with the maximum value (9000) reserved for
when Jumbo frames are enabled. This patch sets the MTU to
the default value for a net device.
It also corrects a discrepancy between MTU values received from
firmware, which includes the ethernet header length, and net
device MTU values.
Finally, it removes redundant min/max MTU assignments after device
initialization.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a copy-paste error, which hides breaking of resume
for CPSW driver: there was replaced netdev_priv() to ndev_to_cpsw(ndev)
in suspend, but left it unchanged in resume.
Fixes: 606f399395
(ti: cpsw: move platform data and slaves info to cpsw_common)
Reported-by: Alexey Starikovskiy <AStarikovskiy@topcon.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 98e3862ca2 ("kcm: fix 0-length case for kcm_sendmsg()")
I tried to avoid skb allocation for 0-length case, but missed
a check for NULL pointer in the non EOR case.
Fixes: 98e3862ca2 ("kcm: fix 0-length case for kcm_sendmsg()")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix hardware setup of multicast address hash:
- Never clear the hardware hash (to avoid packet loss)
- Construct the hash register values in software and then write once
to hardware
Signed-off-by: Rui Sousa <rui.sousa@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan T. Leighton says:
====================
IPv4-mapped on wire, :: dst address issue
Under some circumstances IPv6 datagrams are sent with IPv4-mapped IPv6
addresses as the source. Given an IPv6 socket bound to an IPv4-mapped
IPv6 address, and an IPv6 destination address, both TCP and UDP will
will send packets using the IPv4-mapped IPv6 address as the source. Per
RFC 6890 (Table 20), IPv4-mapped IPv6 source addresses are not allowed
in an IP datagram. The problem can be observed by attempting to
connect() either a TCP or UDP socket, or by using sendmsg() with a UDP
socket. The patch is intended to correct this issue for all socket
types.
linux follows the BSD convention that an IPv6 destination address
specified as in6addr_any is converted to the loopback address.
Currently, neither TCP nor UDP consider the possibility that the source
address is an IPv4-mapped IPv6 address, and assume that the appropriate
loopback address is ::1. The patch adds a check on whether or not the
source address is an IPv4-mapped IPv6 address and then sets the
destination address to either ::ffff:127.0.0.1 or ::1, as appropriate.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check on the type of the source address for the case
where the destination address is in6addr_any. If the source is an
IPv4-mapped IPv6 source address, the destination is changed to
::ffff:127.0.0.1, and otherwise the destination is changed to ::1. This
is done in three locations to handle UDP calls to either connect() or
sendmsg() and TCP calls to connect(). Note that udpv6_sendmsg() delays
handling an in6addr_any destination until very late, so the patch only
needs to handle the case where the source is an IPv4-mapped IPv6
address.
Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check for the problematic case of an IPv4-mapped IPv6
source address and a destination address that is neither an IPv4-mapped
IPv6 address nor in6addr_any, and returns an appropriate error. The
check in done before returning from looking up the route.
Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
When called by HW offloading drivers, the TC action (e.g
net/sched/act_mirred.c) code uses this_cpu logic, e.g
_bstats_cpu_update(this_cpu_ptr(a->cpu_bstats), bytes, packets)
per the kernel documention, preemption should be disabled, add that.
Before the fix, when running with CONFIG_PREEMPT set, we get a
BUG: using smp_processor_id() in preemptible [00000000] code: tc/3793
asserion from the TC action (mirred) stats_update callback.
Fixes: aad7e08d39 ('net/mlx5e: Hardware offloaded flower filter statistics support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=OTHY
-----END PGP SIGNATURE-----
Merge tag 'media/v4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A colorspace regression fix in V4L2 core and a CEC core bug that makes
it discard valid messages"
* tag 'media/v4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] cec: initiator should be the same as the destination for, poll
[media] videodev2.h: go back to limited range Y'CbCr for SRGB and, ADOBERGB
Commit 577fb13199 ("mmc: rework selection of bus speed mode")
refactored bus width selection code to mmc_select_bus_width().
However, it also altered the behavior to not call the selection code in
non-high-speed modes anymore.
This causes 1-bit mode to always be used when the high-speed mode is not
enabled, even though 4-bit and 8-bit bus are valid bus widths in the
backwards-compatibility (legacy) mode as well (see e.g. 5.3.2 Bus Speed
Modes in JEDEC 84-B50). This results in a significant regression in
transfer speeds.
Fix the code to allow 4-bit and 8-bit widths even without high-speed
mode, as before.
Tested with a Zynq-7000 PicoZed 7020 board.
Fixes: 577fb13199 ("mmc: rework selection of bus speed mode")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Herbert Xu says:
====================
rhashtable: Handle table allocation failure during insertion
v2 -
Added Ack to patch 2.
Fixed RCU annotation in code path executed by rehasher by using
rht_dereference_bucket.
v1 -
This series tackles the problem of table allocation failures during
insertion. The issue is that we cannot vmalloc during insertion.
This series deals with this by introducing nested tables.
The first two patches removes manual hash table walks which cannot
work on a nested table.
The final patch introduces nested tables.
I've tested this with test_rhashtable and it appears to work.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code that handles GFP_ATOMIC kmalloc failure on
insertion. As we cannot use vmalloc, we solve it by making our
hash table nested. That is, we allocate single pages at each level
and reach our desired table size by nesting them.
When a nested table is created, only a single page is allocated
at the top-level. Lower levels are allocated on demand during
insertion. Therefore for each insertion to succeed, only two
(non-consecutive) pages are needed.
After a nested table is created, a rehash will be scheduled in
order to switch to a vmalloced table as soon as possible. Also,
the rehash code will never rehash into a nested table. If we
detect a nested table during a rehash, the rehash will be aborted
and a new rehash will be scheduled.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two problems with the function tipc_sk_reinit. Firstly
it's doing a manual walk over an rhashtable. This is broken as
an rhashtable can be resized and if you manually walk over it
during a resize then you may miss entries.
Secondly it's missing memory barriers as previously the code used
spinlocks which provide the barriers implicitly.
This patch fixes both problems.
Fixes: 07f6c4bc04 ("tipc: convert tipc reference table to...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function glock_hash_walk walks the rhashtable by hand. This
is broken because if it catches the hash table in the middle of
a rehash, then it will miss entries.
This patch replaces the manual walk by using the rhashtable walk
interface.
Fixes: 88ffbf3e03 ("GFS2: Use resizable hash table for glocks")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending ARP requests over AX.25 links the hwaddress in the neighbour
cache are not getting initialized. For such an incomplete arp entry
ax2asc2 will generate an empty string resulting in /proc/net/arp output
like the following:
$ cat /proc/net/arp
IP address HW type Flags HW address Mask Device
192.168.122.1 0x1 0x2 52:54:00:00:5d:5f * ens3
172.20.1.99 0x3 0x0 * bpq0
The missing field will confuse the procfs parsing of arp(8) resulting in
incorrect output for the device such as the following:
$ arp
Address HWtype HWaddress Flags Mask Iface
gateway ether 52:54:00:00:5d:5f C ens3
172.20.1.99 (incomplete) ens3
This changes the content of /proc/net/arp to:
$ cat /proc/net/arp
IP address HW type Flags HW address Mask Device
172.20.1.99 0x3 0x0 * * bpq0
192.168.122.1 0x1 0x2 52:54:00:00:5d:5f * ens3
To do so it change ax2asc to put the string "*" in buf for a NULL address
argument. Finally the HW address field is left aligned in a 17 character
field (the length of an ethernet HW address in the usual hex notation) for
readability.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue where the type of counters in the queue(s)
and interface are not in sync (queue counters are int, interface
counters are long), causing incorrect reporting of tx/rx values
of the vif interface and unclear counter overflows.
This patch sets both counters to the u64 type.
Signed-off-by: Mart van Santen <mart@greenhost.nl>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC complains about unused variable 'vma' in mark_screen_rdonly() if THP is
disabled:
arch/x86/kernel/vm86_32.c: In function ‘mark_screen_rdonly’:
arch/x86/kernel/vm86_32.c:180:26: warning: unused variable ‘vma’
[-Wunused-variable]
struct vm_area_struct *vma = find_vma(mm, 0xA0000);
That's silly. pmd_trans_huge() resolves to 0 when THP is disabled, so the
whole block should be eliminated.
Moving the variable declaration outside the if() block shuts GCC up.
Reported-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Tested-by: Borislav Petkov <bp@suse.de>
Cc: Carlos O'Donell <carlos@redhat.com>
Link: http://lkml.kernel.org/r/20170213125228.63645-1-kirill.shutemov@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The ghostprotocols.net domain is not working, remove it from CREDITS and
MAINTAINERS, and change the status to "Odd fixes", and since I haven't
been maintaining those, remove my address from there.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Poll messages that are used to allocate a logical address should
use the same initiator as the destination. Instead, it expected that
the initiator was 0xf which is not according to the standard.
This also had consequences for the message checks in cec_transmit_msg_fh
that incorrectly rejected poll messages with the same initiator and
destination.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This reverts 'commit 7e0739cd9c ("[media] videodev2.h: fix
sYCC/AdobeYCC default quantization range").
The problem is that many drivers can convert R'G'B' content (often
from sensors) to Y'CbCr, but they all produce limited range Y'CbCr.
To stay backwards compatible the default quantization range for
sRGB and AdobeRGB Y'CbCr encoding should be limited range, not full
range, even though the corresponding standards specify full range.
Update the V4L2_MAP_QUANTIZATION_DEFAULT define accordingly and
also update the documentation.
Fixes: 7e0739cd9c ("[media] videodev2.h: fix sYCC/AdobeYCC default quantization range")
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.9 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The UEVENT user mode helper is enabled before the initcalls are executed
and is available when the root filesystem has been mounted.
The user mode helper is triggered by device init calls and the executable
might use the futex syscall.
futex_init() is marked __initcall which maps to device_initcall, but there
is no guarantee that futex_init() is invoked _before_ the first device init
call which triggers the UEVENT user mode helper.
If the user mode helper uses the futex syscall before futex_init() then the
syscall crashes with a NULL pointer dereference because the futex subsystem
has not been initialized yet.
Move futex_init() to core_initcall so futexes are initialized before the
root filesystem is mounted and the usermode helper becomes available.
[ tglx: Rewrote changelog ]
Signed-off-by: Yang Yang <yang.yang29@zte.com.cn>
Cc: jiang.biao2@zte.com.cn
Cc: jiang.zhengxiong@zte.com.cn
Cc: zhong.weidong@zte.com.cn
Cc: deng.huali@zte.com.cn
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1483085875-6130-1-git-send-email-yang.yang29@zte.com.cn
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
tick_broadcast_lock is taken from interrupt context, but the following call
chain takes the lock without disabling interrupts:
[ 12.703736] _raw_spin_lock+0x3b/0x50
[ 12.703738] tick_broadcast_control+0x5a/0x1a0
[ 12.703742] intel_idle_cpu_online+0x22/0x100
[ 12.703744] cpuhp_invoke_callback+0x245/0x9d0
[ 12.703752] cpuhp_thread_fun+0x52/0x110
[ 12.703754] smpboot_thread_fn+0x276/0x320
So the following deadlock can happen:
lock(tick_broadcast_lock);
<Interrupt>
lock(tick_broadcast_lock);
intel_idle_cpu_online() is the only place which violates the calling
convention of tick_broadcast_control(). This was caused by the removal of
the smp function call in course of the cpu hotplug rework.
Instead of slapping local_irq_disable/enable() at the call site, we can
relax the calling convention and handle it in the core code, which makes
the whole machinery more robust.
Fixes: 29d7bbada9 ("intel_idle: Remove superfluous SMP fuction call")
Reported-by: Gabriel C <nix.or.die@gmail.com>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: Ruslan Ruslichenko <rruslich@cisco.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: lwn@lwn.net
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/1486953115.5912.4.camel@gmx.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It seems nobody used LLC since linux-3.12.
Fortunately fuzzers like syzkaller still know how to run this code,
otherwise it would be no fun.
Setting skb->sk without skb->destructor leads to all kinds of
bugs, we now prefer to be very strict about it.
Ideally here we would use skb_set_owner() but this helper does not exist yet,
only CAN seems to have a private helper for that.
Fixes: 376c7311bd ("net: add a temporary sanity check in skb_orphan()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If BPF_F_ALLOW_OVERRIDE flag is used in BPF_PROG_ATTACH command
to the given cgroup the descendent cgroup will be able to override
effective bpf program that was inherited from this cgroup.
By default it's not passed, therefore override is disallowed.
Examples:
1.
prog X attached to /A with default
prog Y fails to attach to /A/B and /A/B/C
Everything under /A runs prog X
2.
prog X attached to /A with allow_override.
prog Y fails to attach to /A/B with default (non-override)
prog M attached to /A/B with allow_override.
Everything under /A/B runs prog M only.
3.
prog X attached to /A with allow_override.
prog Y fails to attach to /A with default.
The user has to detach first to switch the mode.
In the future this behavior may be extended with a chain of
non-overridable programs.
Also fix the bug where detach from cgroup where nothing is attached
was not throwing error. Return ENOENT in such case.
Add several testcases and adjust libbpf.
Fixes: 3007098494 ("cgroup: add support for eBPF programs")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ELAN0605 has been confirmed to be a variant of ELAN0600, which is
blacklisted in the hid-core to be managed by elan_i2c. This device can be
found in Lenovo ideapad 310s (80U4000).
Signed-off-by: Hiroka IHARA <ihara_h@live.jp>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The failure path in ibmvnic_open() mistakenly makes a second call
to napi_enable instead of calling napi_disable. This can result
in a BUG_ON for any queues that were enabled in the previous call
to napi_enable.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize condition variables prior to invoking any work that can
mark them complete. This resolves a race in the ibmvnic driver where
the driver faults trying to complete an uninitialized condition
variable.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 fixes from Ingo Molnar:
"Last minute x86 fixes:
- Fix a softlockup detector warning and long delays if using ptdump
with KASAN enabled.
- Two more TSC-adjust fixes for interesting firmware interactions.
- Two commits to fix an AMD CPU topology enumeration bug that caused
a measurable gaming performance regression"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/ptdump: Fix soft lockup in page table walker
x86/tsc: Make the TSC ADJUST sanitizing work for tsc_reliable
x86/tsc: Avoid the large time jump when sanitizing TSC ADJUST
x86/CPU/AMD: Fix Zen SMT topology
x86/CPU/AMD: Bring back Compute Unit ID
Pull timer fix from Ingo Molnar:
"Fix a sporadic missed timer hw reprogramming bug that can result in
random delays"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/nohz: Fix possible missing clock reprog after tick soft restart
Pull irq fixes from Ingo Molnar:
"Two last minute ARM irqchip driver fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mxs: Enable SKIP_SET_WAKE and MASK_ON_SUSPEND
irqchip/keystone: Fix "scheduling while atomic" on rt
Pull btrfs fixes from Chris Mason:
"This has two last minute fixes. The highest priority here is a
regression fix for the decompression code, but we also fixed up a
problem with the 32-bit compat ioctls.
The decompression bug could hand back the wrong data on big reads when
zlib was used. I have a larger cleanup to make the math here less
error prone, but at this stage in the release Omar's patch is the best
choice"
* 'for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix btrfs_decompress_buf2page()
btrfs: fix btrfs_compat_ioctl failures on non-compat ioctls
Six fairly small fixes. None is a real show stopper, two automation
detected problems: one memory leak, one use after free and four others
each of which fixes something that has been a significant source of
annoyance to someone.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=5Fct
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fairly small fixes. None is a real show stopper, two automation
detected problems: one memory leak, one use after free and four others
each of which fixes something that has been a significant source of
annoyance to someone"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: zfcp: fix use-after-free by not tracing WKA port open/close on failed send
scsi: aacraid: Fix INTx/MSI-x issue with older controllers
scsi: mpt3sas: disable ASPM for MPI2 controllers
scsi: mpt3sas: Force request partial completion alignment
scsi: qla2xxx: Avoid that issuing a LIP triggers a kernel crash
scsi: qla2xxx: Fix a recently introduced memory leak
If btrfs_decompress_buf2page() is handed a bio with its page in the
middle of the working buffer, then we adjust the offset into the working
buffer. After we copy into the bio, we advance the iterator by the
number of bytes we copied. Then, we have some logic to handle the case
of discontiguous pages and adjust the offset into the working buffer
again. However, if we didn't advance the bio to a new page, we may enter
this case in error, essentially repeating the adjustment that we already
made when we entered the function. The end result is bogus data in the
bio.
Previously, we only checked for this case when we advanced to a new
page, but the conversion to bio iterators changed that. This restores
the old, correct behavior.
A case I saw when testing with zlib was:
buf_start = 42769
total_out = 46865
working_bytes = total_out - buf_start = 4096
start_byte = 45056
The condition (total_out > start_byte && buf_start < start_byte) is
true, so we adjust the offset:
buf_offset = start_byte - buf_start = 2287
working_bytes -= buf_offset = 1809
current_buf_start = buf_start = 42769
Then, we copy
bytes = min(bvec.bv_len, PAGE_SIZE - buf_offset, working_bytes) = 1809
buf_offset += bytes = 4096
working_bytes -= bytes = 0
current_buf_start += bytes = 44578
After bio_advance(), we are still in the same page, so start_byte is the
same. Then, we check (total_out > start_byte && current_buf_start < start_byte),
which is true! So, we adjust the values again:
buf_offset = start_byte - buf_start = 2287
working_bytes = total_out - start_byte = 1809
current_buf_start = buf_start + buf_offset = 45056
But note that working_bytes was already zero before this, so we should
have stopped copying.
Fixes: 974b1adc3b ("btrfs: use bio iterators for the decompression handlers")
Reported-by: Pat Erley <pat-lkml@erley.org>
Reviewed-by: Chris Mason <clm@fb.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Tested-by: Liu Bo <bo.li.liu@oracle.com>
Pull networking fixes from David Miller:
1) If the timing is wrong we can indefinitely stop generating new ipv6
temporary addresses, from Marcus Huewe.
2) Don't double free per-cpu stats in ipv6 SIT tunnel driver, from Cong
Wang.
3) Put protections in place so that AF_PACKET is not able to submit
packets which don't even have a link level header to drivers. From
Willem de Bruijn.
4) Fix memory leaks in ipv4 and ipv6 multicast code, from Hangbin Liu.
5) Don't use udp_ioctl() in l2tp code, UDP version expects a UDP socket
and that doesn't go over very well when it is passed an L2TP one.
Fix from Eric Dumazet.
6) Don't crash on NULL pointer in phy_attach_direct(), from Florian
Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
l2tp: do not use udp_ioctl()
xen-netfront: Delete rx_refill_timer in xennet_disconnect_backend()
NET: mkiss: Fix panic
net: hns: Fix the device being used for dma mapping during TX
net: phy: Initialize mdio clock at probe function
igmp, mld: Fix memory leak in igmpv3/mld_del_delrec()
xen-netfront: Improve error handling during initialization
sierra_net: Skip validating irrelevant fields for IDLE LSIs
sierra_net: Add support for IPv6 and Dual-Stack Link Sense Indications
kcm: fix 0-length case for kcm_sendmsg()
xen-netfront: Rework the fix for Rx stall during OOM and network stress
net: phy: Fix PHY module checks and NULL deref in phy_attach_direct()
net: thunderx: Fix PHY autoneg for SGMII QLM mode
net: dsa: Do not destroy invalid network devices
ping: fix a null pointer dereference
packet: round up linear to header len
net: introduce device min_header_len
sit: fix a double free on error path
lwtunnel: valid encap attr check should return 0 when lwtunnel is disabled
ipv6: addrconf: fix generation of new temporary addresses
- Two security related issues in the rxe driver
- One compile issue in the RDMA uapi header
-----BEGIN PGP SIGNATURE-----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=zGBQ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Third round of -rc fixes for 4.10 kernel:
- two security related issues in the rxe driver
- one compile issue in the RDMA uapi header"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
RDMA: Don't reference kernel private header from UAPI header
IB/rxe: Fix mem_check_range integer overflow
IB/rxe: Fix resid update
Anssi Hannula