Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Including (in no particular order):
- Page table code for AMD IOMMU now supports large pages where
smaller page-sizes were mapped before. VFIO had to work around
that in the past and I included a patch to remove it (acked by
Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would
never work as modules anyway.
- Work to unify the the iommu-related pointers in
'struct device' into one pointer. This work is not finished
yet, but will probably be in the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=DT9A
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- Page table code for AMD IOMMU now supports large pages where smaller
page-sizes were mapped before. VFIO had to work around that in the
past and I included a patch to remove it (acked by Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would never
work as modules anyway.
- Work to unify the the iommu-related pointers in 'struct device' into
one pointer. This work is not finished yet, but will probably be in
the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
* tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (78 commits)
iommu: Check for iommu_ops == NULL in iommu_probe_device()
ACPI/IORT: Don't call iommu_ops->add_device directly
iommu/of: Don't call iommu_ops->add_device directly
iommu: Consolitate ->add/remove_device() calls
iommu/sysfs: Rename iommu_release_device()
dmaengine: sh: rcar-dmac: Use device_iommu_mapped()
xhci: Use device_iommu_mapped()
powerpc/iommu: Use device_iommu_mapped()
ACPI/IORT: Use device_iommu_mapped()
iommu/of: Use device_iommu_mapped()
driver core: Introduce device_iommu_mapped() function
iommu/tegra: Use helper functions to access dev->iommu_fwspec
iommu/qcom: Use helper functions to access dev->iommu_fwspec
iommu/of: Use helper functions to access dev->iommu_fwspec
iommu/mediatek: Use helper functions to access dev->iommu_fwspec
iommu/ipmmu-vmsa: Use helper functions to access dev->iommu_fwspec
iommu/dma: Use helper functions to access dev->iommu_fwspec
iommu/arm-smmu: Use helper functions to access dev->iommu_fwspec
ACPI/IORT: Use helper functions to access dev->iommu_fwspec
iommu: Introduce wrappers around dev->iommu_fwspec
...
Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems to
be the "collection of various driver subsystems not big enough to have
their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems. This was discussed at the
Plumbers conference a few months ago and knocked into mergable shape
very fast by Christian Brauner. Who also has signed up to be
another binder maintainer, showing a distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCZCUA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymF9QCgx/Z8Fj1qzGVGrIE4flXOi7pxOrgAoMqJEWtU
ywwL8M9suKDz7cZT9fWQ
=xxr6
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems
to be the "collection of various driver subsystems not big enough to
have their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems.
This was discussed at the Plumbers conference a few months ago and
knocked into mergable shape very fast by Christian Brauner. Who
also has signed up to be another binder maintainer, showing a
distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (116 commits)
MAINTAINERS: add another Android binder maintainer
intel_th: msu: Fix an off-by-one in attribute store
stm class: Add a reference to the SyS-T document
stm class: Fix a module refcount leak in policy creation error path
char: lp: use new parport device model
char: lp: properly count the lp devices
char: lp: use first unused lp number while registering
char: lp: detach the device when parallel port is removed
char: lp: introduce list to save port number
bus: qcom: remove duplicated include from qcom-ebi2.c
VMCI: Use memdup_user() rather than duplicating its implementation
char/rtc: Use of_node_name_eq for node name comparisons
misc: mic: fix a DMA pool free failure
ptp: fix an IS_ERR() vs NULL check
genwqe: Fix size check
binder: implement binderfs
binder: fix use-after-free due to ksys_close() during fdget()
bus: fsl-mc: remove duplicated include files
bus: fsl-mc: explicitly define the fsl_mc_command endianness
misc: ti-st: make array read_ver_cmd static, shrinks object size
...
* Add support for the security features of nvdimm devices that
implement a security model similar to ATA hard drive security. The
security model supports locking access to the media at
device-power-loss, to be unlocked with a passphrase, and secure-erase
(crypto-scramble).
Unlike the ATA security case where the kernel expects device
security to be managed in a pre-OS environment, the libnvdimm security
implementation allows key provisioning and key-operations at OS
runtime. Keys are managed with the kernel's encrypted-keys facility to
provide data-at-rest security for the libnvdimm key material. The
usage model mirrors fscrypt key management, but is driven via
libnvdimm sysfs.
* Miscellaneous updates for api usage and comment fixes.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJcJalaAAoJEB7SkWpmfYgCmpkP/35Isou2xxbYdICt9HR4WjiE
E4r66Ck+ivZW4oEAub3RQw/SwcZePjuHArO5MgVGFoM1dBMABE+JvKiZm1xybCil
iuWT/V7ozlNf5LuvacvjUXe/suUIoqji9yzLEEx9mDaISehrYvvy579DFxkE8Aww
8Vcx8E1DQkXiWY4d9nmDmAjt8GQPNmsdHfTwMcJg7XSywTkURF64vW7/94aN8QtV
rH5ZKKOra8Lqn0S05RoH4XegZcE6TZxgE23ZXsobBJrWdbGVFmgbz6AaewJc/+QU
ZW3dx/1NAe7Op25xewJOjdG/Kl0gzWtqCrHCu8LeaSjwtHsgMQ/FBhL9g/7GRtHt
hcQy12Iu9YTn3FOl8yfNRKb7lE5/1nJ2MtW8Z55WKHONHzN9cgrZLOwmpTYgrR/r
SmIzwKNFavLwwz9bj+paHhmTngLDnNbvR6FwAKwSbWinotbLEyfMhU1jJ9RmHxSV
M+jqS1BJ9IvH+WVN5bVa7oCNpVeq6yMw0Ow2vWXMPbiwh17ShACI59paqZKRiR06
WH8SgdTPOZuMndtQV+m8zFBiJtmgAtGSiN8c1A/1QZJHDTpXz2MdWhtx5McvFsZ9
Jot4Vd8mFWI7oVLdb+PF/AGZnKNAnD8PdsAlFws0k7+rM6lf6gf5n/CkjjMuSapG
Q/kf0cOpPq8wdsrnOzyc
=7KYd
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"The vast bulk of this update is the new support for the security
capabilities of some nvdimms.
The userspace tooling for this capability is still a work in progress,
but the changes survive the existing libnvdimm unit tests. The changes
also pass manual checkout on hardware and the new nfit_test emulation
of the security capability.
The touches of the security/keys/ files have received the necessary
acks from Mimi and David. Those changes were necessary to allow for a
new generic encrypted-key type, and allow the nvdimm sub-system to
lookup key material referenced by the libnvdimm-sysfs interface.
Summary:
- Add support for the security features of nvdimm devices that
implement a security model similar to ATA hard drive security. The
security model supports locking access to the media at
device-power-loss, to be unlocked with a passphrase, and
secure-erase (crypto-scramble).
Unlike the ATA security case where the kernel expects device
security to be managed in a pre-OS environment, the libnvdimm
security implementation allows key provisioning and key-operations
at OS runtime. Keys are managed with the kernel's encrypted-keys
facility to provide data-at-rest security for the libnvdimm key
material. The usage model mirrors fscrypt key management, but is
driven via libnvdimm sysfs.
- Miscellaneous updates for api usage and comment fixes"
* tag 'libnvdimm-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (21 commits)
libnvdimm/security: Quiet security operations
libnvdimm/security: Add documentation for nvdimm security support
tools/testing/nvdimm: add Intel DSM 1.8 support for nfit_test
tools/testing/nvdimm: Add overwrite support for nfit_test
tools/testing/nvdimm: Add test support for Intel nvdimm security DSMs
acpi/nfit, libnvdimm/security: add Intel DSM 1.8 master passphrase support
acpi/nfit, libnvdimm/security: Add security DSM overwrite support
acpi/nfit, libnvdimm: Add support for issue secure erase DSM to Intel nvdimm
acpi/nfit, libnvdimm: Add enable/update passphrase support for Intel nvdimms
acpi/nfit, libnvdimm: Add disable passphrase support to Intel nvdimm.
acpi/nfit, libnvdimm: Add unlock of nvdimm support for Intel DIMMs
acpi/nfit, libnvdimm: Add freeze security support to Intel nvdimm
acpi/nfit, libnvdimm: Introduce nvdimm_security_ops
keys-encrypted: add nvdimm key format type to encrypted keys
keys: Export lookup_user_key to external users
acpi/nfit, libnvdimm: Store dimm id as a member to struct nvdimm
libnvdimm, namespace: Replace kmemdup() with kstrndup()
libnvdimm, label: Switch to bitmap_zalloc()
ACPI/nfit: Adjust annotation for why return 0 if fail to find NFIT at start
libnvdimm, bus: Check id immediately following ida_simple_get
...
A huge update this time, but a lot of that is just consolidating or
removing code:
- provide a common DMA_MAPPING_ERROR definition and avoid indirect
calls for dma_map_* error checking
- use direct calls for the DMA direct mapping case, avoiding huge
retpoline overhead for high performance workloads
- merge the swiotlb dma_map_ops into dma-direct
- provide a generic remapping DMA consistent allocator for architectures
that have devices that perform DMA that is not cache coherent. Based
on the existing arm64 implementation and also used for csky now.
- improve the dma-debug infrastructure, including dynamic allocation
of entries (Robin Murphy)
- default to providing chaining scatterlist everywhere, with opt-outs
for the few architectures (alpha, parisc, most arm32 variants) that
can't cope with it
- misc sparc32 dma-related cleanups
- remove the dma_mark_clean arch hook used by swiotlb on ia64 and
replace it with the generic noncoherent infrastructure
- fix the return type of dma_set_max_seg_size (Niklas Söderlund)
- move the dummy dma ops for not DMA capable devices from arm64 to
common code (Robin Murphy)
- ensure dma_alloc_coherent returns zeroed memory to avoid kernel data
leaks through userspace. We already did this for most common
architectures, but this ensures we do it everywhere.
dma_zalloc_coherent has been deprecated and can hopefully be
removed after -rc1 with a coccinelle script.
-----BEGIN PGP SIGNATURE-----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=in72
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.21' of git://git.infradead.org/users/hch/dma-mapping
Pull DMA mapping updates from Christoph Hellwig:
"A huge update this time, but a lot of that is just consolidating or
removing code:
- provide a common DMA_MAPPING_ERROR definition and avoid indirect
calls for dma_map_* error checking
- use direct calls for the DMA direct mapping case, avoiding huge
retpoline overhead for high performance workloads
- merge the swiotlb dma_map_ops into dma-direct
- provide a generic remapping DMA consistent allocator for
architectures that have devices that perform DMA that is not cache
coherent. Based on the existing arm64 implementation and also used
for csky now.
- improve the dma-debug infrastructure, including dynamic allocation
of entries (Robin Murphy)
- default to providing chaining scatterlist everywhere, with opt-outs
for the few architectures (alpha, parisc, most arm32 variants) that
can't cope with it
- misc sparc32 dma-related cleanups
- remove the dma_mark_clean arch hook used by swiotlb on ia64 and
replace it with the generic noncoherent infrastructure
- fix the return type of dma_set_max_seg_size (Niklas Söderlund)
- move the dummy dma ops for not DMA capable devices from arm64 to
common code (Robin Murphy)
- ensure dma_alloc_coherent returns zeroed memory to avoid kernel
data leaks through userspace. We already did this for most common
architectures, but this ensures we do it everywhere.
dma_zalloc_coherent has been deprecated and can hopefully be
removed after -rc1 with a coccinelle script"
* tag 'dma-mapping-4.21' of git://git.infradead.org/users/hch/dma-mapping: (73 commits)
dma-mapping: fix inverted logic in dma_supported
dma-mapping: deprecate dma_zalloc_coherent
dma-mapping: zero memory returned from dma_alloc_*
sparc/iommu: fix ->map_sg return value
sparc/io-unit: fix ->map_sg return value
arm64: default to the direct mapping in get_arch_dma_ops
PCI: Remove unused attr variable in pci_dma_configure
ia64: only select ARCH_HAS_DMA_COHERENT_TO_PFN if swiotlb is enabled
dma-mapping: bypass indirect calls for dma-direct
vmd: use the proper dma_* APIs instead of direct methods calls
dma-direct: merge swiotlb_dma_ops into the dma_direct code
dma-direct: use dma_direct_map_page to implement dma_direct_map_sg
dma-direct: improve addressability error reporting
swiotlb: remove dma_mark_clean
swiotlb: remove SWIOTLB_MAP_ERROR
ACPI / scan: Refactor _CCA enforcement
dma-mapping: factor out dummy DMA ops
dma-mapping: always build the direct mapping code
dma-mapping: move dma_cache_sync out of line
dma-mapping: move various slow path functions out of line
...
* Use common helpers, bitmap_zalloc() and kstrndup(), to replace open
coded versions.
* Clarify the comments around hotplug vs initial init case for the nfit
driver.
* Cleanup the libnvdimm init path.
- Introduce "software nodes", analogous to the DT and ACPI firmware
nodes except that they can be created by kernel code, in order to
complement fwnodes representing real firmware nodes when they are
incomplete (for example missing device properties) and to supply
the primary fwnode when the firmware lacks hardware description
for a device completely, and replace the "property_set" struct
fwnode_handle type with software nodes (Heikki Krogerus).
- Clean up the just introduced software nodes support and fix a commet
in the graph-handling code (Colin Ian King, Marco Felsch).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Z3Zj
-----END PGP SIGNATURE-----
Merge tag 'devprop-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework updates from Rafael Wysocki:
"This introduces 'software nodes' that are analogous to the DT and ACPI
firmware nodes except that they can be created by drivers themselves
and do a couple of assorted cleanups.
Specifics:
- Introduce "software nodes", analogous to the DT and ACPI firmware
nodes except that they can be created by kernel code, in order to
complement fwnodes representing real firmware nodes when they are
incomplete (for example missing device properties) and to supply
the primary fwnode when the firmware lacks hardware description for
a device completely, and replace the "property_set" struct
fwnode_handle type with software nodes (Heikki Krogerus).
- Clean up the just introduced software nodes support and fix a
commet in the graph-handling code (Colin Ian King, Marco Felsch)"
* tag 'devprop-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: fix fwnode_graph_get_next_endpoint() documentation
drivers: base: swnode: remove need for a temporary string for the node name
device property: Remove struct property_set
device property: Move device_add_properties() to swnode.c
drivers: base: Introducing software nodes to the firmware node framework
ACPI / glue: Add acpi_platform_notify() function
drivers core: Prepare support for multiple platform notifications
driver core: platform: Remove duplicated device_remove_properties() call
- Update the ACPICA code in the kernel to the 20181213 upstream
revision including:
* New Windows _OSI strings (Bob Moore, Jung-uk Kim).
* Buffers-to-string conversions update (Bob Moore).
* Removal of support for expressions in package elements (Bob
Moore).
* New option to display method/object evaluation in debug output
(Bob Moore).
* Compiler improvements (Bob Moore, Erik Schmauss).
* Minor debugger fix (Erik Schmauss).
* Disassembler improvement (Erik Schmauss).
* Assorted cleanups (Bob Moore, Colin Ian King, Erik Schmauss).
- Add support for a new OEM _OSI string to indicate special handling
of secondary graphics adapters on some systems (Alex Hung).
- Make it possible to build the ACPI subystem without PCI support
(Sinan Kaya).
- Make the SPCR table handling regard baud rate 0 in accordance with
the specification of it and make the DSDT override code support
DSDT code names generated by recent ACPICA (Andy Shevchenko, Wang
Dongsheng, Nathan Chancellor).
- Add clock frequency for Hisilicon Hip08 SPI controller to the ACPI
driver for AMD SoCs (APD) (Jay Fang).
- Fix the PM handling during device init in the ACPI driver for
Intel SoCs (LPSS) (Hans de Goede).
- Avoid double panic()s by clearing the APEI GHES block_status
before panic() (Lenny Szubowicz).
- Clean up a function invocation in the ACPI core and get rid of
some code duplication by using the DEFINE_SHOW_ATTRIBUTE macro
in the APEI support code (Alexey Dobriyan, Yangtao Li).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=yxXc
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to the 20181213 upstream
revision, make it possible to build the ACPI subsystem without PCI
support, and a new OEM _OSI string, add a new device support to the
ACPI driver for AMD SoCs and fix PM handling in the ACPI driver for
Intel SoCs, fix the SPCR table handling and do some assorted fixes and
cleanups.
Specifics:
- Update the ACPICA code in the kernel to the 20181213 upstream
revision including:
* New Windows _OSI strings (Bob Moore, Jung-uk Kim).
* Buffers-to-string conversions update (Bob Moore).
* Removal of support for expressions in package elements (Bob
Moore).
* New option to display method/object evaluation in debug output
(Bob Moore).
* Compiler improvements (Bob Moore, Erik Schmauss).
* Minor debugger fix (Erik Schmauss).
* Disassembler improvement (Erik Schmauss).
* Assorted cleanups (Bob Moore, Colin Ian King, Erik Schmauss).
- Add support for a new OEM _OSI string to indicate special handling
of secondary graphics adapters on some systems (Alex Hung).
- Make it possible to build the ACPI subystem without PCI support
(Sinan Kaya).
- Make the SPCR table handling regard baud rate 0 in accordance with
the specification of it and make the DSDT override code support
DSDT code names generated by recent ACPICA (Andy Shevchenko, Wang
Dongsheng, Nathan Chancellor).
- Add clock frequency for Hisilicon Hip08 SPI controller to the ACPI
driver for AMD SoCs (APD) (Jay Fang).
- Fix the PM handling during device init in the ACPI driver for Intel
SoCs (LPSS) (Hans de Goede).
- Avoid double panic()s by clearing the APEI GHES block_status before
panic() (Lenny Szubowicz).
- Clean up a function invocation in the ACPI core and get rid of some
code duplication by using the DEFINE_SHOW_ATTRIBUTE macro in the
APEI support code (Alexey Dobriyan, Yangtao Li)"
* tag 'acpi-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (31 commits)
ACPI / tables: Add an ifdef around amlcode and dsdt_amlcode
ACPI/APEI: Clear GHES block_status before panic()
ACPI: Make PCI slot detection driver depend on PCI
ACPI/IORT: Stub out ACS functions when CONFIG_PCI is not set
arm64: select ACPI PCI code only when both features are enabled
PCI/ACPI: Allow ACPI to be built without CONFIG_PCI set
ACPICA: Remove PCI bits from ACPICA when CONFIG_PCI is unset
ACPI: Allow CONFIG_PCI to be unset for reboot
ACPI: Move PCI reset to a separate function
ACPI / OSI: Add OEM _OSI string to enable dGPU direct output
ACPI / tables: add DSDT AmlCode new declaration name support
ACPICA: Update version to 20181213
ACPICA: change coding style to match ACPICA, no functional change
ACPICA: Debug output: Add option to display method/object evaluation
ACPICA: disassembler: disassemble OEMx tables as AML
ACPICA: Add "Windows 2018.2" string in the _OSI support
ACPICA: Expressions in package elements are not supported
ACPICA: Update buffer-to-string conversions
ACPICA: add comments, no functional change
ACPICA: Remove defines that use deprecated flag
...
- Add sysadmin documentation for cpuidle (Rafael Wysocki).
- Make it possible to specify a cpuidle governor from kernel
command line, add new cpuidle state sysfs attributes for
governor evaluation, and improve the "polling" idle state
handling (Rafael Wysocki).
- Fix the handling of the "required-opps" DT property in the
operating performance points (OPP) framework, improve the
integration of it with the generic power domains (genpd)
framework, improve the handling of performance states in
them and clean up the idle states vs performance states
separation in genpd (Viresh Kumar, Ulf Hansson).
- Add a cpufreq driver called "qcom-hw" for Qualcomm SoCs using
a hardware engine to control CPU frequency transitions along
with DT bindings for it (Taniya Das).
- Fix an intel_pstate driver issue related to CPU offline and
update the documentation of it (Srinivas Pandruvada).
- Clean up the imx6q cpufreq driver (Anson Huang).
- Add SPDX license IDs to cpufreq schedutil governor files (Daniel
Lezcano).
- Switch over the runtime PM framework to using high-res timers
for device autosuspend to allow the control of it to be more
precise (Vincent Guittot).
- Disable non-wakeup ACPI GPEs during suspend-to-idle so that they
don't prevent the system from reaching the target low-power state
and simplify the suspend-to-idle handling on ACPI platforms
without full Low-Power S0 Idle (LPS0) support (Rafael Wysocki).
- Add system-wide suspend and resume support to the devfreq
framework (Lukasz Luba).
- Clean up the SmartReflex adaptive voltage scaling (AVS) driver and
add an SPDX license ID to it (Nishanth Menon, Uwe Kleine-König,
Thomas Meyer).
- Get rid of code duplication by using the DEFINE_SHOW_ATTRIBUTE
macro in some places, fix some DT node refcount leaks, and do
some other janitorial cleanups (Yangtao Li).
- Update the cpupower, intel_pstate_tracer and turbosat utilities
(Abhishek Goel, Doug Smythies, Len Brown).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=WhM8
-----END PGP SIGNATURE-----
Merge tag 'pm-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add sysadmin documentation for cpuidle, extend the cpuidle
subsystem somewhat, improve the handling of performance states in the
generic power domains (genpd) and operating performance points (OPP)
frameworks, add a new cpufreq driver for Qualcomm SoCs, update some
other cpufreq drivers, switch over the runtime PM framework to using
high-res timers for device autosuspend, fix a problem with
suspend-to-idle on ACPI-based platforms, add system-wide suspend and
resume handling to the devfreq framework, do some janitorial cleanups
all over and update some utilities.
Specifics:
- Add sysadmin documentation for cpuidle (Rafael Wysocki).
- Make it possible to specify a cpuidle governor from kernel command
line, add new cpuidle state sysfs attributes for governor
evaluation, and improve the "polling" idle state handling (Rafael
Wysocki).
- Fix the handling of the "required-opps" DT property in the
operating performance points (OPP) framework, improve the
integration of it with the generic power domains (genpd) framework,
improve the handling of performance states in them and clean up the
idle states vs performance states separation in genpd (Viresh
Kumar, Ulf Hansson).
- Add a cpufreq driver called "qcom-hw" for Qualcomm SoCs using a
hardware engine to control CPU frequency transitions along with DT
bindings for it (Taniya Das).
- Fix an intel_pstate driver issue related to CPU offline and update
the documentation of it (Srinivas Pandruvada).
- Clean up the imx6q cpufreq driver (Anson Huang).
- Add SPDX license IDs to cpufreq schedutil governor files (Daniel
Lezcano).
- Switch over the runtime PM framework to using high-res timers for
device autosuspend to allow the control of it to be more precise
(Vincent Guittot).
- Disable non-wakeup ACPI GPEs during suspend-to-idle so that they
don't prevent the system from reaching the target low-power state
and simplify the suspend-to-idle handling on ACPI platforms without
full Low-Power S0 Idle (LPS0) support (Rafael Wysocki).
- Add system-wide suspend and resume support to the devfreq framework
(Lukasz Luba).
- Clean up the SmartReflex adaptive voltage scaling (AVS) driver and
add an SPDX license ID to it (Nishanth Menon, Uwe Kleine-König,
Thomas Meyer).
- Get rid of code duplication by using the DEFINE_SHOW_ATTRIBUTE
macro in some places, fix some DT node refcount leaks, and do some
other janitorial cleanups (Yangtao Li).
- Update the cpupower, intel_pstate_tracer and turbosat utilities
(Abhishek Goel, Doug Smythies, Len Brown)"
* tag 'pm-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (54 commits)
PM / Domains: remove define_genpd_open_function() and define_genpd_debugfs_fops()
PM-runtime: Switch autosuspend over to using hrtimers
cpufreq: qcom-hw: Add support for QCOM cpufreq HW driver
dt-bindings: cpufreq: Introduce QCOM cpufreq firmware bindings
ACPI: PM: Loop in full LPS0 mode only
ACPI: EC / PM: Disable non-wakeup GPEs for suspend-to-idle
tools/power/x86/intel_pstate_tracer: Fix non root execution for post processing a trace file
tools/power turbostat: consolidate duplicate model numbers
tools/power turbostat: fix goldmont C-state limit decoding
PM / Domains: Propagate performance state updates
PM / Domains: Factorize dev_pm_genpd_set_performance_state()
PM / Domains: Save OPP table pointer in genpd
OPP: Don't return 0 on error from of_get_required_opp_performance_state()
OPP: Add dev_pm_opp_xlate_performance_state() helper
OPP: Improve _find_table_of_opp_np()
PM / Domains: Make genpd performance states orthogonal to the idlestates
PM / sleep: convert to DEFINE_SHOW_ATTRIBUTE
cpuidle: Add 'above' and 'below' idle state metrics
PM / AVS: SmartReflex: Switch to SPDX Licence ID
PM / AVS: SmartReflex: NULL check before some freeing functions is not needed
...
The USB Power Delivery discrete components now can be enumerated by
i2c-multi-instantiate driver via several resources under single ACPI
device node (ACPI ID is INT3515).
Touchscreen support is added for the Mediacom Flexbook Edge 11.
Mellanox driver got fixed due to updates in their firmware.
The power management stub driver for AtomISP v2 is fixed in order to support
Intel Baytrail SoCs where same quirk is needed for S0ix to work.
Special key handling has been fixed for Favorites hotkey on Thinkpad, and
Screen LOCK on ASUS.
Ideapad Yoga 2 13 has no HW rfkill switch, thus, driver has been updated
to support this.
Few cleanups related to debugfs have been made in Intel IPS and
Intel PMC drivers. Besides that Intel PMC has been extended
to show more detailed information about Latency Tolerance.
The following is an automated git shortlog grouped by driver:
ACPI / scan:
- Create platform device for INT3515 ACPI nodes
Add the VLV ISP PCI ID to atomisp2_pm:
- Add the VLV ISP PCI ID to atomisp2_pm
asus-nb-wmi:
- Drop mapping of 0x33 and 0x34 scan codes
- Map 0x35 to KEY_SCREENLOCK
asus-wmi:
- Tell the EC the OS will handle the display off hotkey
dell-laptop:
- Mark expected switch fall-throughs
Documentation/ABI:
- Add new attribute for mlxreg-io sysfs interfaces
Fix config space access for intel_atomisp2_pm:
- Fix config space access for intel_atomisp2_pm
i2c:
- acpi: Introduce i2c_acpi_get_i2c_resource() helper
- acpi: Use ACPI_FAILURE instead of !ACPI_SUCCESS
- acpi: Return error pointers from i2c_acpi_new_device()
i2c-multi-instantiate:
- Allow to have same slaves
- Introduce IOAPIC IRQ support
- Distinguish IRQ resource type
- Count I2cSerialBus() resources
- Get rid of obsolete conditional
- Defer probe when no adapter found
- Accept errors of i2c_acpi_new_device()
ideapad-laptop:
- Add Yoga 2 13 to no_hw_rfkill list
iio:
- inv_mpu6050: Use i2c_acpi_get_i2c_resource() helper
intel_cht_int33fe:
- Get rid of obsolete conditional
- Accept errors of i2c_acpi_new_device()
- Remove duplicate NULL check
intel_ips:
- Convert to use DEFINE_SHOW_ATTRIBUTE macro
- Remove never happen condition
- NULL check before some freeing functions is not needed
- remove unnecessary checks in ips_debugfs_init
intel_pmc_core:
- convert to DEFINE_SHOW_ATTRIBUTE
- Decode Snoop / Non Snoop LTR
- Fix LTR IGNORE Max offset
- Show Latency Tolerance info
intel_telemetry:
- convert to DEFINE_SHOW_ATTRIBUTE
mlx-platform:
- Convert to use SPDX identifier
- Allow mlxreg-io driver activation for new systems
- Fix LED configuration
- Fix tachometer registers
- Rename new systems product names
- Add definitions for new registers
thinkpad_acpi:
- Cleanup quirks macros
- Change the keymap for Favorites hotkey
touchscreen_dmi:
- Add info for the Mediacom Flexbook Edge 11
-----BEGIN PGP SIGNATURE-----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=kYH6
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.21-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
- The USB Power Delivery discrete components now can be enumerated by
i2c-multi-instantiate driver via several resources under single ACPI
device node (ACPI ID is INT3515).
- Touchscreen support is added for the Mediacom Flexbook Edge 11.
- Mellanox driver got fixed due to updates in their firmware.
- The power management stub driver for AtomISP v2 is fixed in order to
support Intel Baytrail SoCs where same quirk is needed for S0ix to
work.
- Special key handling has been fixed for Favorites hotkey on Thinkpad,
and Screen LOCK on ASUS.
- Ideapad Yoga 2 13 has no HW rfkill switch, thus, driver has been
updated to support this.
- Few cleanups related to debugfs have been made in Intel IPS and Intel
PMC drivers. Besides that Intel PMC has been extended to show more
detailed information about Latency Tolerance
* tag 'platform-drivers-x86-v4.21-1' of git://git.infradead.org/linux-platform-drivers-x86: (41 commits)
platform/x86: mlx-platform: Convert to use SPDX identifier
Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces
platform/x86: mlx-platform: Allow mlxreg-io driver activation for new systems
platform/x86: mlx-platform: Fix LED configuration
platform/x86: mlx-platform: Fix tachometer registers
platform/x86: mlx-platform: Rename new systems product names
platform/x86: mlx-platform: Add definitions for new registers
platform/x86: intel_telemetry: convert to DEFINE_SHOW_ATTRIBUTE
platform/x86: intel_pmc_core: convert to DEFINE_SHOW_ATTRIBUTE
platform/x86: thinkpad_acpi: Cleanup quirks macros
platform/x86: touchscreen_dmi: Add info for the Mediacom Flexbook Edge 11
platform/x86: Fix config space access for intel_atomisp2_pm
platform/x86: Add the VLV ISP PCI ID to atomisp2_pm
platform/x86: intel_ips: Convert to use DEFINE_SHOW_ATTRIBUTE macro
platform/x86: intel_ips: Remove never happen condition
platform/x86: intel_ips: NULL check before some freeing functions is not needed
platform/x86: intel_ips: remove unnecessary checks in ips_debugfs_init
iio: inv_mpu6050: Use i2c_acpi_get_i2c_resource() helper
ACPI / scan: Create platform device for INT3515 ACPI nodes
platform/x86: i2c-multi-instantiate: Allow to have same slaves
...
With Intel DSM 1.8 [1] two new security DSMs are introduced. Enable/update
master passphrase and master secure erase. The master passphrase allows
a secure erase to be performed without the user passphrase that is set on
the NVDIMM. The commands of master_update and master_erase are added to
the sysfs knob in order to initiate the DSMs. They are similar in opeartion
mechanism compare to update and erase.
[1]: http://pmem.io/documents/NVDIMM_DSM_Interface-V1.8.pdf
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add support for the NVDIMM_FAMILY_INTEL "ovewrite" capability as
described by the Intel DSM spec v1.7. This will allow triggering of
overwrite on Intel NVDIMMs. The overwrite operation can take tens of
minutes. When the overwrite DSM is issued successfully, the NVDIMMs will
be unaccessible. The kernel will do backoff polling to detect when the
overwrite process is completed. According to the DSM spec v1.7, the 128G
NVDIMMs can take up to 15mins to perform overwrite and larger DIMMs will
take longer.
Given that overwrite puts the DIMM in an indeterminate state until it
completes introduce the NDD_SECURITY_OVERWRITE flag to prevent other
operations from executing when overwrite is happening. The
NDD_WORK_PENDING flag is added to denote that there is a device reference
on the nvdimm device for an async workqueue thread context.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add support to issue a secure erase DSM to the Intel nvdimm. The
required passphrase is acquired from an encrypted key in the kernel user
keyring. To trigger the action, "erase <keyid>" is written to the
"security" sysfs attribute.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add support to disable passphrase (security) for the Intel nvdimm. The
passphrase used for disabling is pulled from an encrypted-key in the kernel
user keyring. The action is triggered by writing "disable <keyid>" to the
sysfs attribute "security".
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* acpi-pci:
ACPI: Make PCI slot detection driver depend on PCI
ACPI/IORT: Stub out ACS functions when CONFIG_PCI is not set
arm64: select ACPI PCI code only when both features are enabled
PCI/ACPI: Allow ACPI to be built without CONFIG_PCI set
ACPICA: Remove PCI bits from ACPICA when CONFIG_PCI is unset
ACPI: Allow CONFIG_PCI to be unset for reboot
ACPI: Move PCI reset to a separate function
* acpi-tables:
ACPI / tables: Add an ifdef around amlcode and dsdt_amlcode
ACPI / tables: add DSDT AmlCode new declaration name support
ACPI: SPCR: Consider baud rate 0 as preconfigured state
* acpi-soc:
ACPI / LPSS: Ignore acpi_device_fix_up_power() return value
ACPI / APD: Add clock frequency for Hisilicon Hip08 SPI controller
* acpi-apei:
ACPI/APEI: Clear GHES block_status before panic()
ACPI, APEI, EINJ: Change to use DEFINE_SHOW_ATTRIBUTE macro
* acpi-misc:
ACPI: fix acpi_find_child_device() invocation in acpi_preset_companion()
* acpica:
ACPICA: Update version to 20181213
ACPICA: change coding style to match ACPICA, no functional change
ACPICA: Debug output: Add option to display method/object evaluation
ACPICA: disassembler: disassemble OEMx tables as AML
ACPICA: Add "Windows 2018.2" string in the _OSI support
ACPICA: Expressions in package elements are not supported
ACPICA: Update buffer-to-string conversions
ACPICA: add comments, no functional change
ACPICA: Remove defines that use deprecated flag
ACPICA: Add "Windows 2018" string in the _OSI support
ACPICA: Update version to 20181031
ACPICA: iASL: Enhance error detection
ACPICA: iASL: adding definition and disassembly for TPM2 revision 3
ACPICA: Use %d for signed int print formatting instead of %u
ACPICA: Debugger: refactor to fix unused variable warning
In __ghes_panic() clear the block status in the APEI generic
error status block for that generic hardware error source before
calling panic() to prevent a second panic() in the crash kernel
for exactly the same fatal error.
Otherwise ghes_probe(), running in the crash kernel, would see
an unhandled error in the APEI generic error status block and
panic again, thereby precluding any crash dump.
Signed-off-by: Lenny Szubowicz <lszubowi@redhat.com>
Signed-off-by: David Arcari <darcari@redhat.com>
Tested-by: Tyler Baicar <baicar.tyler@gmail.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since this is ACPI PCI slot detection driver for PCI, it doesn't make sense
to compile this without PCI support in place.
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove PCI dependent code out of iort.c when CONFIG_PCI is not defined.
A quick search reveals the following functions:
1. pci_request_acs()
2. pci_domain_nr()
3. pci_is_root_bus()
4. to_pci_dev()
Both pci_domain_nr() and pci_is_root_bus() are defined in linux/pci.h.
pci_domain_nr() is a stub function when CONFIG_PCI is not set and
pci_is_root_bus() just returns a reference to a structure member which
is still valid without CONFIG_PCI set.
to_pci_dev() is a macro that expands to container_of.
pci_request_acs() is the only code that gets pulled in from drivers/pci/*.c
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We are compiling PCI code today for systems with ACPI and no PCI
device present. Remove the useless code and reduce the tight
dependency.
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # PCI parts
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Allow ACPI to be built without PCI support in place.
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make PCI reboot conditional on CONFIG_PCI set on the kernel configuration.
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Getting ready to factor out PCI specific code when CONFIG_PCI is unset.
Create a acpi_pci_reset() that kick starts PCI specific reset.
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For HP Inc. mobile workstation with hybrid graphics support, dGPU can
directly output to external monitors; however, Nvidia and AMD's Linux
drivers aren't able to support this feature.
The OEM _OSI string "Linux-HPI-Hybrid-Graphics" is used by BIOS to
implement dGPU direct output to external monitors.
The form of the OEM _OSI strings is defined by each OEMs and is
discussed in Documentation/acpi/osi.txt.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After a previous change, all non-wakeup GPEs are disabled for
suspend-to-idle unless full Low-Power S0 (LPS0) mode is in use, so
it is not necessary to do anything in acpi_s2idle_wake() unless in
full LPS0 mode, which is only when lps0_device_handle is set.
Modify the code accordingly.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are systems in which non-wakeup GPEs fire during the "noirq"
suspend stage of suspending devices and that effectively prevents the
system that tries to suspend to idle from entering any low-power
state at all. If the offending GPE fires regularly and often enough,
the system appears to be suspended, but in fact it is in a tight loop
over "noirq" suspend and "noirq" resume of devices all the time.
To prevent that from happening, disable all non-wakeup GPEs except
for the EC GPE for suspend-to-idle (the EC GPE is special, because
on some systems it has to be enabled for power button wakeup events
to be generated as expected).
Fixes: 147a7d9d25 (ACPI / PM: Do not reconfigure GPEs for suspend-to-idle)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201987
Reported-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make sure to invoke this call-back through the proper
function of the IOMMU-API.
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Replace the iommu-check with a proper and readable function
call.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use the new helpers dev_iommu_fwspec_get()/set() to access
the dev->iommu_fwspec pointer. This makes it easier to move
that pointer later into another struct.
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add support to unlock the dimm via the kernel key management APIs. The
passphrase is expected to be pulled from userspace through keyutils.
The key management and sysfs attributes are libnvdimm generic.
Encrypted keys are used to protect the nvdimm passphrase at rest. The
master key can be a trusted-key sealed in a TPM, preferred, or an
encrypted-key, more flexible, but more exposure to a potential attacker.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Co-developed-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add support for freeze security on Intel nvdimm. This locks out any
changes to security for the DIMM until a hard reset of the DIMM is
performed. This is triggered by writing "freeze" to the generic
nvdimm/nmemX "security" sysfs attribute.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Co-developed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Some NVDIMMs, like the ones defined by the NVDIMM_FAMILY_INTEL command
set, expose a security capability to lock the DIMMs at poweroff and
require a passphrase to unlock them. The security model is derived from
ATA security. In anticipation of other DIMMs implementing a similar
scheme, and to abstract the core security implementation away from the
device-specific details, introduce nvdimm_security_ops.
Initially only a status retrieval operation, ->state(), is defined,
along with the base infrastructure and definitions for future
operations.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Co-developed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The generated dimm id is needed for the sysfs attribute as well as being
used as the identifier/description for the security key. Since it's
constant and should never change, store it as a member of struct nvdimm.
As nvdimm_create() continues to grow parameters relative to NFIT driver
requirements, do not require other implementations to keep pace.
Introduce __nvdimm_create() to carry the new parameters and keep
nvdimm_create() with the long standing default api.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A new naming rule was added in ACPICA version 20180427 changing
the DSDT AML code name from "AmlCode" to "dsdt_aml_code".
That change was made by commit 83b2fa943b "ACPICA: iASL: Enhance
the -tc option (create AML hex file in C)".
Tested:
ACPICA release version 20180427+.
ARM64: QCOM QDF2400
GCC: 4.8.5 20150623
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This commit alters the coding style of the following commit to match
ACPICA to keep divergences between Linux and ACPICA at a minimum.
This is not intended to result in functional changes.
ae6b3e54aa
Author: Hans de Goede <hdegoede@redhat.com>
Date: Sun Nov 18 20:25:35 2018 +0100
ACPICA: Fix handling of buffer-size in acpi_ex_write_data_to_field()
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Adds entry/exit messages for all objects that are evaluated.
Works for the kernel-level code as well as acpiexec. The "-eo"
flag enables acpiexec to display these messages.
The messages are very useful when debugging the flow of table
initialization.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jung-uk Kim <jkim@free_BSD.org>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Return AE_SUPPORT if encountered, fixes a previous fault if
encountered.
Note: Other ACPI implementations do not support this type of
construct.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add "0x" prefix for hex values.
Provides compatibility with other ACPI implementations.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This commit removes the use of ACPI_NO_METHOD_EXECUTE flag
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Latest windows string.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rather than checking the DMA attribute at each callsite, just pass it
through for acpi_dma_configure() to handle directly. That can then deal
with the relatively exceptional DEV_DMA_NOT_SUPPORTED case by explicitly
installing dummy DMA ops instead of just skipping setup entirely. This
will then free up the dev->dma_ops == NULL case for some valuable
fastpath optimisations.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Tony Luck <tony.luck@intel.com>
Ignore acpi_device_fix_up_power() return value. If we return an error
we end up with acpi_default_enumeration() still creating a platform-
device for the device and we end up with the device still being used
but without the special LPSS related handling which is not useful.
Specicifically ignoring the error fixes the touchscreen no longer
working after a suspend/resume on a Prowise PT301 tablet.
This tablet has a broken _PS0 method on the touchscreen's I2C controller,
causing acpi_device_fix_up_power() to fail, causing fallback to standard
platform-dev handling and specifically causing acpi_lpss_save/restore_ctx
to not run.
The I2C controllers _PS0 method does actually turn on the device, but then
does some more nonsense which fails when run during early boot trying to
use I2C opregion handling on another not-yet registered I2C controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The SPI clock frequency of Designware IP for Hisilicon Hip08 is 250M.
The ACPI ID used is "HISI0173".
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds