Quite often drivers set only "write" permission assuming that this
includes "read" permission as well and this works on plenty of
platforms. However IODA2 is strict about this and produces an EEH when
"read" permission is not set and reading happens.
This adds a workaround in the IODA code to always add the "read" bit
when the "write" bit is set.
Fixes: 10b35b2b74 ("powerpc/powernv: Do not set "read" flag if direction==DMA_NONE")
Cc: stable@vger.kernel.org # 4.2+
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Tested-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With ppc64 we use the deposited pgtable_t to store the hash pte slot
information. We should not withdraw the deposited pgtable_t without
marking the pmd none. This ensure that low level hash fault handling
will skip this huge pte and we will handle them at upper levels.
Recent change to pmd splitting changed the above in order to handle the
race between pmd split and exit_mmap. The race is explained below.
Consider following race:
CPU0 CPU1
shrink_page_list()
add_to_swap()
split_huge_page_to_list()
__split_huge_pmd_locked()
pmdp_huge_clear_flush_notify()
// pmd_none() == true
exit_mmap()
unmap_vmas()
zap_pmd_range()
// no action on pmd since pmd_none() == true
pmd_populate()
As result the THP will not be freed. The leak is detected by check_mm():
BUG: Bad rss-counter state mm:ffff880058d2e580 idx:1 val:512
The above required us to not mark pmd none during a pmd split.
The fix for ppc is to clear the huge pte of _PAGE_USER, so that low
level fault handling code skip this pte. At higher level we do take ptl
lock. That should serialze us against the pmd split. Once the lock is
acquired we do check the pmd again using pmd_same. That should always
return false for us and hence we should retry the access. We do the
pmd_same check in all case after taking plt with
THP (do_huge_pmd_wp_page, do_huge_pmd_numa_page and
huge_pmd_set_accessed)
Also make sure we wait for irq disable section in other cpus to finish
before flipping a huge pte entry with a regular pmd entry. Code paths
like find_linux_pte_or_hugepte depend on irq disable to get
a stable pte_t pointer. A parallel thp split need to make sure we
don't convert a pmd pte to a regular pmd entry without waiting for the
irq disable section to finish.
Fixes: eef1b3ba05 ("thp: implement split_huge_pmd()")
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When PCI bus is unplugged during full hotplug for EEH recovery,
the platform PE instance (struct pnv_ioda_pe) isn't released and
it dereferences the stale PCI bus that has been released. It leads
to kernel crash when referring to the stale PCI bus.
This fixes the issue by correcting the PE's primary bus when it's
oneline at plugging time, in pnv_pci_dma_bus_setup() which is to
be called by pcibios_fixup_bus().
Cc: stable@vger.kernel.org # v4.1+
Reported-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reported-by: Pradipta Ghosh <pradghos@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When PE is created, its primary bus is cached to pe->bus. At later
point, the cached primary bus is returned from eeh_pe_bus_get().
However, we could get stale cached primary bus and run into kernel
crash in one case: full hotplug as part of fenced PHB error recovery
releases all PCI busses under the PHB at unplugging time and recreate
them at plugging time. pe->bus is still dereferencing the PCI bus
that was released.
This adds another PE flag (EEH_PE_PRI_BUS) to represent the validity
of pe->bus. pe->bus is updated when its first child EEH device is
online and the flag is set. Before unplugging in full hotplug for
error recovery, the flag is cleared.
Fixes: 8cdb2833 ("powerpc/eeh: Trace PCI bus from PE")
Cc: stable@vger.kernel.org #v3.11+
Reported-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reported-by: Pradipta Ghosh <pradghos@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If a cpu is hotplugged while the hcall trace points are active, it's
possible to hit a warning from RCU due to the trace points calling into
RCU from an offline cpu, eg:
RCU used illegally from offline CPU!
rcu_scheduler_active = 1, debug_locks = 1
Make the hypervisor tracepoints conditional by using
TRACE_EVENT_FN_COND.
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since binutils 2.26 BFD is doing suffix merging on STRTAB sections. But
dedotify modifies the symbol names in place, which can also modify
unrelated symbols with a name that matches a suffix of a dotted name. To
remove the leading dot of a symbol name we can just increment the pointer
into the STRTAB section instead.
Backport to all stables to avoid breakage when people update their
binutils - mpe.
Cc: stable@vger.kernel.org
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In file included from mm/vmscan.c:54:0:
include/linux/swapops.h: In function ‘pte_to_swp_entry’:
include/linux/swapops.h:69:2: error: implicit declaration of function ‘pte_swp_soft_dirty’ [-Werror=implicit-function-declaration]
if (pte_swp_soft_dirty(pte))
^
include/linux/swapops.h:70:3: error: implicit declaration of function ‘pte_swp_clear_soft_dirty’ [-Werror=implicit-function-declaration]
pte = pte_swp_clear_soft_dirty(pte);
We support soft dirty tracking only with book3s 64 for now.
So change the Kconfig dependency accordingly. Also CHECKPOINT_RESTORE
feature is not really dependent on SOFT_DIRTY. We track the dependency
between MEM_SOFT_DIRTY and ARCH_SOFT_DIRTY through headers
Fixes: 7207f43665 ("powerpc/mm: Add page soft dirty tracking")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This was wrongly updated by commit 7aa9a23c69 ("powerpc, thp: remove
infrastructure for handling splitting PMDs") during the last merge
window. Fix it up.
This could lead to incorrect behaviour in THP and/or mprotect(), at a
minimum.
Fixes: 7aa9a23c69 ("powerpc, thp: remove infrastructure for handling splitting PMDs")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 7a7868326d ("powerpc/perf: Add an explict flag indicating
presence of SLOT field") introduced the PPMU_HAS_SSLOT flag to remove
the assumption that MMCRA[SLOT] was present when PPMU_ALT_SIPR was not
set.
That commit's changelog also mentions that Power8 does not support
MMCRA[SLOT]. However when the Power8 PMU support was merged, it
errnoeously included the PPMU_HAS_SSLOT flag.
So remove PPMU_HAS_SSLOT from the Power8 flags.
mpe: On systems where MMCRA[SLOT] exists, the field occupies bits 37:39
(IBM numbering). On Power8 bit 37 is reserved, and 38:39 overlap with
the high bits of the Threshold Event Counter Mantissa. I am not aware of
any published events which use the threshold counting mechanism, which
would cause the mantissa bits to be set. So in practice this bug is
unlikely to trigger.
Fixes: e05b9b9e5c ("powerpc/perf: Power8 PMU support")
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In eeh_pe_loc_get(), the PE location code is retrieved from the
"ibm,loc-code" property of the device node for the bridge of the
PE's primary bus. It's not correct because the property indicates
the parent PE's location code.
This reads the correct PE location code from "ibm,io-base-loc-code"
or "ibm,slot-location-code" property of PE parent bus's device node.
Cc: stable@vger.kernel.org # v3.16+
Fixes: 357b2f3dd9 ("powerpc/eeh: Dump PE location code")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With commit 90a545e9 (restrict /dev/mem to idle io memory ranges) mapping
rtas_rmo_buf from user space is failing. Hence we are not able to make
RTAS syscall.
This patch calls page_is_rtas_user_buf before calling iomem_is_exclusive
in devmem_is_allowed(). This will allow user space to map rtas_rmo_buf
and we are able to make RTAS syscall.
Reported-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
CC: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit d5d6a443b2 ("arch/powerpc/include/asm/pgtable-ppc64.h:
add pmd_[dirty|mkclean] for THP") added a new identical definition
of pmd_dirty(). Remove it again.
Cc: Minchan Kim <minchan@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PowerPC64 uses the symbol .TOC. much as other targets use
_GLOBAL_OFFSET_TABLE_. It identifies the value of the GOT pointer (or in
powerpc parlance, the TOC pointer). Global offset tables are generally
local to an executable or shared library, or in the kernel, module. Thus
it does not make sense for a module to resolve a relocation against
.TOC. to the kernel's .TOC. value. A module has its own .TOC., and
indeed the powerpc64 module relocation processing ignores the kernel
value of .TOC. and instead calculates a module-local value.
This patch removes code involved in exporting the kernel .TOC., tweaks
modpost to ignore an undefined .TOC., and the module loader to twiddle
the section symbol so that .TOC. isn't seen as undefined.
Note that if the kernel was compiled with -msingle-pic-base then ELFv2
would not have function global entry code setting up r2. In that case
the module call stubs would need to be modified to set up r2 using the
kernel .TOC. value, requiring some of this code to be reinstated.
mpe: Furthermore a change in binutils master (not yet released) causes
the current way we handle the TOC to no longer work when building with
MODVERSIONS=y and RELOCATABLE=n. The symptom is that modules can not be
loaded due to there being no version found for TOC.
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Alan Modra <amodra@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Test runs on a ppc64 BE guest succeeded using modified fstests.
Also tested on ppc64 LE using a home made test - mpe.
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add intel punit and telemetry driver for APL SoCs.
Add intel-hid driver for various laptop hotkey support.
Add asus-wireless radio control driver.
Keyboard backlight support/improvements for ThinkPads, Vaio, and Toshiba.
Several hotkey related fixes and improvements for dell and toshiba.
Fix oops on dual GPU Macs in apple-gmux.
A few new device IDs and quirks.
Various minor config related build issues and cleanups.
surface pro 4:
- fix compare_const_fl.cocci warnings
- Add support for Surface Pro 4 Buttons
platform/x86:
- Add Intel Telemetry Debugfs interfaces
- Add Intel telemetry platform device
- Add Intel telemetry platform driver
- Add Intel Telemetry Core Driver
- add NULL check for input parameters
- add Intel P-Unit mailbox IPC driver
- update acpi resource structure for Punit
thinkpad_acpi:
- Add support for keyboard backlight
dell-wmi:
- Process only one event on devices with interface version 0
- Check if Dell WMI descriptor structure is valid
- Improve unknown hotkey handling
- Use a C99-style array for bios_to_linux_keycode
tc1100-wmi:
- fix build warning when CONFIG_PM not enabled
asus-wireless:
- Add ACPI HID ATK4001
- Add Asus Wireless Radio Control driver
asus-wmi:
- drop to_platform_driver macro
intel-hid:
- new hid event driver for hotkeys
sony-laptop:
- Keyboard backlight control for some Vaio Fit models
ideapad-laptop:
- Add Lenovo ideapad Y700-17ISK to no_hw_rfkill dmi list
apple-gmux:
- Assign apple_gmux_data before registering
toshiba_acpi:
- Add rfkill dependency to ACPI_TOSHIBA entry
- Fix keyboard backlight sysfs entries not being updated
- Add WWAN RFKill support
- Add support for WWAN devices
- Fix blank screen at boot if transflective backlight is supported
- Propagate the hotkey value via genetlink
toshiba_bluetooth:
- Add missing newline in toshiba_bluetooth_present function
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWnuSYAAoJEKbMaAwKp364xckH/A/INtwr1LzmSw8fsEIe6IGQ
MKEzCHZOUdSPcZSHcTW/fE/J8kt1j4YdR2kkxNbivtxST5O81E6KfAmo37TRrTNx
bunVt7Swj7FcPsm6t0m3PQkbWkOy3UMUncRaZjeofzhRl2m+bHEycEIJsHs7OU+e
7UPjbWZjRz6/LahcryKDH/lRhweMEsgZSFzjNlby8Wzz4LRCu8HLwNGUQa0vQfNI
2UW+s7g2ZkFXx9fbmWu9twkyP7LwNoaZ3IDGsEffIYjmXeZKe+yTPy/TueYYzpon
aclJSjhxLNnfWUaO0eUt/H4T5VyUag3v3mp6PVSwm2TA3Cpuh1SDYrJcurls6Mw=
=b4Wa
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.5-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Add intel punit and telemetry driver for APL SoCs.
Add intel-hid driver for various laptop hotkey support.
Add asus-wireless radio control driver.
Keyboard backlight support/improvements for ThinkPads, Vaio, and Toshiba.
Several hotkey related fixes and improvements for dell and toshiba.
Fix oops on dual GPU Macs in apple-gmux.
A few new device IDs and quirks.
Various minor config related build issues and cleanups.
surface pro 4:
- fix compare_const_fl.cocci warnings
- Add support for Surface Pro 4 Buttons
platform/x86:
- Add Intel Telemetry Debugfs interfaces
- Add Intel telemetry platform device
- Add Intel telemetry platform driver
- Add Intel Telemetry Core Driver
- add NULL check for input parameters
- add Intel P-Unit mailbox IPC driver
- update acpi resource structure for Punit
thinkpad_acpi:
- Add support for keyboard backlight
dell-wmi:
- Process only one event on devices with interface version 0
- Check if Dell WMI descriptor structure is valid
- Improve unknown hotkey handling
- Use a C99-style array for bios_to_linux_keycode
tc1100-wmi:
- fix build warning when CONFIG_PM not enabled
asus-wireless:
- Add ACPI HID ATK4001
- Add Asus Wireless Radio Control driver
asus-wmi:
- drop to_platform_driver macro
intel-hid:
- new hid event driver for hotkeys
sony-laptop:
- Keyboard backlight control for some Vaio Fit models
ideapad-laptop:
- Add Lenovo ideapad Y700-17ISK to no_hw_rfkill dmi list
apple-gmux:
- Assign apple_gmux_data before registering
toshiba_acpi:
- Add rfkill dependency to ACPI_TOSHIBA entry
- Fix keyboard backlight sysfs entries not being updated
- Add WWAN RFKill support
- Add support for WWAN devices
- Fix blank screen at boot if transflective backlight is supported
- Propagate the hotkey value via genetlink
toshiba_bluetooth:
- Add missing newline in toshiba_bluetooth_present function"
* tag 'platform-drivers-x86-v4.5-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (29 commits)
surface pro 4: fix compare_const_fl.cocci warnings
surface pro 4: Add support for Surface Pro 4 Buttons
platform:x86: Add Intel Telemetry Debugfs interfaces
platform:x86: Add Intel telemetry platform device
platform:x86: Add Intel telemetry platform driver
platform/x86: Add Intel Telemetry Core Driver
intel_punit_ipc: add NULL check for input parameters
thinkpad_acpi: Add support for keyboard backlight
dell-wmi: Process only one event on devices with interface version 0
dell-wmi: Check if Dell WMI descriptor structure is valid
tc1100-wmi: fix build warning when CONFIG_PM not enabled
asus-wireless: Add ACPI HID ATK4001
platform/x86: Add Asus Wireless Radio Control driver
asus-wmi: drop to_platform_driver macro
intel-hid: new hid event driver for hotkeys
Keyboard backlight control for some Vaio Fit models
platform/x86: Add rfkill dependency to ACPI_TOSHIBA entry
platform:x86: add Intel P-Unit mailbox IPC driver
intel_pmc_ipc: update acpi resource structure for Punit
ideapad-laptop: Add Lenovo ideapad Y700-17ISK to no_hw_rfkill dmi list
...
Intel PM Telemetry is a software mechanism via which various SoC
PM and performance related parameters like PM counters, firmware
trace verbosity, the status of different devices inside the SoC, etc.
can be monitored and analyzed. The different samples that may be
monitored can be configured at runtime via exported APIs.
This patch adds the telemetry core driver that implements basic
exported APIs.
Signed-off-by: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This driver provides support for P-Unit mailbox IPC on Intel platforms.
The heart of the P-Unit is the Foxton microcontroller and its firmware,
which provide mailbox interface for power management usage.
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This adds a new kind of barrier, and reworks virtio and xen
to use it.
Plus some fixes here and there.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWlU2kAAoJECgfDbjSjVRpZ6IH/Ra19ecG8sCQo9zskr4zo22Z
DZXC3u0sJDBYjjBAiw3IY1FKh7wx2Fr1RhUOj1bteBgcFCMCV1zInP5ITiCyzd1H
YYh1w9C2tZaj2T4t9L4hIrAdtIF8fGS+oI2IojXPjOuDLEt6pfFBEjHp/sfl3UJq
ZmZvw4OXviSNej7jBw8Xni3Uv18yfmLGXvMdkvMSPC1/XL29voGDqTVwhqJwxLVz
k/ZLcKFOzIs9N7Nja0Jl1EiZtC2Y9cpItqweicNAzszlpkSL44vQxmCSefB+WyQ4
gt0O3+AxYkLfrxzCBhUA4IpRex3/XPW1b+1e/V1XjfR2n/FlyLe+AIa8uPJElFc=
=ukaV
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio barrier rework+fixes from Michael Tsirkin:
"This adds a new kind of barrier, and reworks virtio and xen to use it.
Plus some fixes here and there"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (44 commits)
checkpatch: add virt barriers
checkpatch: check for __smp outside barrier.h
checkpatch.pl: add missing memory barriers
virtio: make find_vqs() checkpatch.pl-friendly
virtio_balloon: fix race between migration and ballooning
virtio_balloon: fix race by fill and leak
s390: more efficient smp barriers
s390: use generic memory barriers
xen/events: use virt_xxx barriers
xen/io: use virt_xxx barriers
xenbus: use virt_xxx barriers
virtio_ring: use virt_store_mb
sh: move xchg_cmpxchg to a header by itself
sh: support 1 and 2 byte xchg
virtio_ring: update weak barriers to use virt_xxx
Revert "virtio_ring: Update weak barriers to use dma_wmb/rmb"
asm-generic: implement virt_xxx memory barriers
x86: define __smp_xxx
xtensa: define __smp_xxx
tile: define __smp_xxx
...
Pull arch/tile updates from Chris Metcalf:
"This is a grab bag of changes that includes some NOHZ and
context-tracking related changes, some debugging improvements,
JUMP_LABEL support, and some fixes for tilepro allmodconfig support.
We also remove the now-unused node_has_online_mem() definitions both
for tile's asm/topology.h as well as in linux/topology.h itself"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
numa: remove stale node_has_online_mem() define
arch/tile: move user_exit() to early kernel entry sequence
tile: fix bug in setting PT_FLAGS_DISABLE_IRQ on kernel entry
tile: fix tilepro casts for readl, writel, etc
tile: fix a -Wframe-larger-than warning
tile: include the syscall number in the backtrace
MAINTAINERS: add git URL for tile
arch/tile: adopt prepare_exit_to_usermode() model from x86
tile/jump_label: add jump label support for TILE-Gx
tile: define a macro ktext_writable_addr to get writable kernel text address
Pull AVR32 updates from Hans-Christian Noren Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
mmc: atmel: get rid of struct mci_dma_data
mmc: atmel-mci: restore dma on AVR32
avr32: wire up missing syscalls
avr32: wire up accept4 syscall
Pull more networking fixes from David Miller:
1) Fix brcmfmac build with older gcc, from Arend van Spriel.
2) IRQ values unintentionally truncated to u8 in mlx5 driver, from
Doron Tsur.
3) Fix build warnings wrt tcp cgroup changes, from Geert Uytterhoeven.
4) Limit deep recursion in ovs stack, from Hannes Frederic Sowa.
5) at803x phy driver bug fixes from, Martin Blumenstingl.
6) Fix TSO handling in hns driver, from Daode Huang
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits)
ovs: limit ovs recursions in ovs_execute_actions to not corrupt stack
team: Replace rcu_read_lock with a mutex in team_vlan_rx_kill_vid
net: hns: bug fix about hisilicon TSO BD mode
brcmfmac: fix BRCMF_FW_NVRAM_DEF macro for older gcc compilers
net: phy: at803x: Add the interrupt register bit definitions
net: phy: at803x: Clean up duplicate register definitions
net: phy: at803x: Allow specifying the RGMII RX clock delay via phy mode
net: phy: at803x: Don't set gbit features for the AR8030 phy
arm64: bpf: add extra pass to handle faulty codegen
arm64: insn: remove BUG_ON from codegen
sctp: the temp asoc's transports should not be hashed/unhashed
net/mlx5_core: Fix trimming down IRQ number
tcp_memcontrol: Forward declare cgroup_subsys and mem_cgroup stucts
batman-adv: Drop immediate orig_node free function
batman-adv: Drop immediate batadv_hard_iface free function
batman-adv: Drop immediate neigh_ifinfo free function
batman-adv: Drop immediate batadv_hardif_neigh_node free function
batman-adv: Drop immediate batadv_neigh_node free function
batman-adv: Drop immediate batadv_orig_ifinfo free function
batman-adv: Avoid recursive call_rcu for batadv_nc_node
...
This isn't used anywhere, so delete it.
Looks like the last usage (in x86-specific code) was removed by Tejun
in 2011 in commit bd6709a91a ("x86, NUMA: Make 32bit use common NUMA
init path").
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
This ensures that we always notify context tracking that we
have exited from user space no matter how we enter the kernel.
It is similar to how arm64 handles context tracking, for example.
This allows the removal of all the exception_enter() calls that
were added in commit 49e4e15619 ("tile: support CONTEXT_TRACKING and
thus NOHZ_FULL").
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
This flag value is saved in ptregs and used to decide whether
to disable irqs when returning from the kernel. Commit 1168df528fe4
("tile: don't assume user privilege is zero") performed a bad
merge from some KVM-enabled code that had not yet been upstreamed.
The only issue with the old code is that we will read the interrupt
mask in more conditions than we need to (e.g., coming from user
space when user space has the Interrupt Critical Section bit set, or
coming from a guest kernel), which is a slow multi-cycle operation.
This change saves those few cycles in the common case.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Missing parentheses could cause an argument of the form
"integer + pointer" to get cast to "(long)integer + pointer"
and remain a pointer type, causing compiler warnings.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
The warning occurs in setup.c, where it is known that it can't be
a problem, but it's still a good idea to silence the warning.
The onstack array is converted from an s32 to a u8, which still
is plenty of range for the values being managed there.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
This information is easily available in the backtrace data and can
be helpful when trying to figure out the backtrace, particularly
if we're early in kernel entry or late in kernel exit.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
This change is a prerequisite change for TASK_ISOLATION but also
stands on its own for readability and maintainability. The existing
tile do_work_pending() was called in a loop from assembly on
the slow path; this change moves the loop into C code as well.
For the x86 version see commit c5c46f59e4 ("x86/entry: Add new,
comprehensible entry and exit handlers written in C").
This change exposes a pre-existing bug on the older tilepro platform;
the singlestep processing is done last, but on tilepro (unlike tilegx)
we enable interrupts while doing that processing, so we could in
theory miss a signal or other asynchronous event. A future change
could fix this by breaking the singlestep work into a "prepare"
step done in the main loop, and a "trigger" step done after exiting
the loop. Since this change is intended as purely a restructuring
change, we call out the bug explicitly now, but don't yet fix it.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Code generation functions in arch/arm64/kernel/insn.c previously
BUG_ON invalid parameters. Following change of that behavior, now we
need to handle the error case where AARCH64_BREAK_FAULT is returned.
Instead of error-handling on every emit() in JIT, we add a new
validation pass at the end of JIT compilation. There's no point in
running JITed code at run-time only to trap due to AARCH64_BREAK_FAULT.
Instead, we drop this failed JIT compilation and allow the system to
gracefully fallback on the BPF interpreter.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During code generation, we used to BUG_ON unknown/unsupported encoding
or invalid parameters.
Instead, now we report these as errors and simply return the
instruction AARCH64_BREAK_FAULT. Users of these codegen helpers should
check for and handle this failure condition as appropriate.
Otherwise, unhandled codegen failure will result in trapping at
run-time due to AARCH64_BREAK_FAULT, which is arguably better than a
BUG_ON.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.5. I don't think I've missed
anything too major, I'm mostly back at work now but I'll probably get
some sleep in 5 years time.
Summary:
New drivers:
- etnaviv:
GPU driver for the 3D core on the Vivante core used in numerous
ARM boards.
Highlights:
Core:
- Atomic suspend/resume helpers
- Move the headers to using userspace friendlier types.
- Documentation updates
- Lots of struct_mutex removal.
- Bunch of DP MST fixes from AMD.
Panel:
- More DSI helpers
- Support for some new basic panels
i915:
- Basic Kabylake support
- DP link training and detect code refactoring
- fbc/psr fixes
- FIFO underrun fixes
- SDE interrupt handling fixes
- dma-buf/fence support in pageflip path.
- GPU side for MST audio support
radeon/amdgpu:
- Drop UMS support
- GPUVM/Scheduler optimisations
- Initial Powerplay support for Tonga/Fiji/CZ/ST
- ACP audio prerequisites
nouveau:
- GK20a instmem improvements
- PCIE link speed change support
msm:
- DSI support for msm8960/apq8064
tegra:
- Host1X support for Tegra210 SoC
vc4:
- 3D acceleration support
armada:
- Get rid of struct mutex
tda998x:
- Atomic modesetting support
- TMDS clock limitations
omapdrm:
- Atomic modesetting support
- improved TILER performance
rockchip:
- RK3036 VOP support
- Atomic modesetting support
- Synopsys DW MIPI DSI support
exynos:
- Runtime PM support
- of_graph binding for DP panels
- Cleanup of IPP code
- Configurable plane support
- Kernel panic fixes at release time"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (711 commits)
drm/fb_cma_helper: Remove implicit call to disable_unused_functions
drm/amdgpu: add missing irq.h include
drm/vmwgfx: Fix a width / pitch mismatch on framebuffer updates
drm/vmwgfx: Fix an incorrect lock check
drm: nouveau: fix nouveau_debugfs_init prototype
drm/nouveau/pci: fix check in nvkm_pcie_set_link
drm/amdgpu: validate duplicates first
drm/amdgpu: move VM page tables to the LRU end on CS v2
drm/ttm: add ttm_bo_move_to_lru_tail function v2
drm/ttm: fix adding foreign BOs to the swap LRU
drm/ttm: fix adding foreign BOs to the LRU during init v2
drm/radeon: use kobj_to_dev()
drm/amdgpu: use kobj_to_dev()
drm/amdgpu/cz: force vce clocks when sclks are forced
drm/amdgpu/cz: force uvd clocks when sclks are forced
drm/amdgpu/cz: add code to enable forcing VCE clocks
drm/amdgpu/cz: add code to enable forcing UVD clocks
drm/amdgpu: fix lost sync_to if scheduler is enabled.
drm/amd/powerplay: fix static checker warning for return meaningless value.
drm/sysfs: use kobj_to_dev()
...
Pull parsic updates from Helge Deller:
"This patchset includes two major fixes which are both scheduled for
stable:
First, __ARCH_SI_PREAMBLE_SIZE was defined with a wrong value.
Second, huge page pte and TLB changes needed protection with a
spinlock. Other than that there are just some trivial optimizations
and cleanups"
* 'parisc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Protect huge page pte changes with spinlocks
parisc: Imporove debug info about space registers and TLB configuration
parisc: Drop parisc-specific NSIGTRAP define
parisc: Fix __ARCH_SI_PREAMBLE_SIZE
parisc: Reduce overhead of parisc_requires_coherency()
parisc: Initialize PCI bridge cache line and default latency
Merge second patch-bomb from Andrew Morton:
- more MM stuff:
- Kirill's page-flags rework
- Kirill's now-allegedly-fixed THP rework
- MADV_FREE implementation
- DAX feature work (msync/fsync). This isn't quite complete but DAX
is new and it's good enough and the guys have a handle on what
needs to be done - I expect this to be wrapped in the next week or
two.
- some vsprintf maintenance work
- various other misc bits
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (145 commits)
printk: change recursion_bug type to bool
lib/vsprintf: factor out %pN[F] handler as netdev_bits()
lib/vsprintf: refactor duplicate code to special_hex_number()
printk-formats.txt: remove unimplemented %pT
printk: help pr_debug and pr_devel to optimize out arguments
lib/test_printf.c: test dentry printing
lib/test_printf.c: add test for large bitmaps
lib/test_printf.c: account for kvasprintf tests
lib/test_printf.c: add a few number() tests
lib/test_printf.c: test precision quirks
lib/test_printf.c: check for out-of-bound writes
lib/test_printf.c: don't BUG
lib/kasprintf.c: add sanity check to kvasprintf
lib/vsprintf.c: warn about too large precisions and field widths
lib/vsprintf.c: help gcc make number() smaller
lib/vsprintf.c: expand field_width to 24 bits
lib/vsprintf.c: eliminate potential race in string()
lib/vsprintf.c: move string() below widen_string()
lib/vsprintf.c: pull out padding code from dentry_name()
printk: do cond_resched() between lines while outputting to consoles
...
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
We've had quite busy weeks in this cycle. Looking at ALSA core, the
significant changes are a few fixes wrt timer and sequencer ioctls
that have been revealed by fuzzer recently. Other than that, ASoC
core got a few updates about DAI link handling, but these are rather
straightforward refactoring.
In drivers scene, ASoC received quite lots of new drivers in addition
to bunch of updates for still ongoing Intel Skylake support and
topology API. HD-audio gained a new HDMI/DP hotplug notification via
component. FireWire got a pile of code refactoring/updates with
SCS.1x driver integration.
More highlights are shown below.
[NOTE: this contains also many commits for DRM. This is due to the
pull of drm stable branch into sound tree, as the base of i915 audio
component work for HD-audio. The highlights below don't contain
these DRM changes, as these are supposed to be pulled via drm tree in
anyway sooner or later.]
Core
- Handful fixes to harden ALSA timer and sequencer ioctls against
races reported by syzkaller fuzzer
- Irq description string can be unique to each card; only for
HD-audio for now
ASoC
- Conversion of the array of DAI links to a list for supporting
dynamically adding and removing DAI links
- Topology API enhancements to make everything more component based
and being able to specify PCM links via topology
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production; we really need to get to the
point where that can be done
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come
- Lots of new features and cleanups for the Renesas drivers
- ANC support for WM5110
- New drivers: Imagination Technologies IPs, Atmel class D speaker,
Cirrus CS47L24 and WM1831, Dialog DA7128, Realtek RT5659 and
RT56156, Rockchip RK3036, TI PC3168A, and AMD ACP
- Rename PCM1792a driver to be generic pcm179x
HD-Audio
- Use audio component for i915 HDMI/DP hotplug handling
- On-demand binding with i915 driver
- bdl_pos_adj parameter adjustment for Baytrail controllers
- Enable power_save_node for CX20722; this shouldn't lead to
regression, hopefully
- Kabylake HDMI/DP codec support
- Quirks for Lenovo E50-80, Dell Latitude E-series, and other Dell
machines
- A few code refactoring
FireWire
- Lots of code cleanup and refactoring
- Integrate the support of SCS.1x devices into snd-oxfw driver;
snd-scs1x driver is obsoleted
USB-audio
- Fix possible NULL dereference at disconnection
- A regression fix for Native Instruments devices
Misc
- A few code cleanups of fm801 driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJWmmhNAAoJEGwxgFQ9KSmk/wsP/3eO+giAT9VRPa6qxR6VdT6I
dZwTxcp4ZzUrgLxk9k5VYjqey6QL+1xWfl3Abrd+NzXDj1wo4KsDh2XCKG1btO9K
UpIZf76Nzt7o91pzHbsU6mrjDeoVNqloZoGbg1utAmmegaXH3owd18p/ZHfE3sz2
BbaHmYW/R8lnaBgBhzqJB97+zRaLJmMWpWHfpHaIPjdfw8/V4j76jtPnpmv2hDZl
BHXVHcQXjVGunFRzxdzBLuTC+FmhzUeTAbbAdOT4fEoOCv5MtZqYppNxdhj+b9l5
mrsXe5FBTNmrt9Z5TtfCuzgJPkzoDperFb0aKd7wI1jVMtLzkNCMlanHr9U6B6fr
jSrs6l25xrpF1BBfRMfHjNudA5vng/XC5dtW00JofXSrIxtwPNUoDDiqJgw7xVm5
aVWK7KkQIjRbHdCQaeTymv70oHHKei92hbCrXUobXZ7wLeJMXNVPT25ttChWrgAI
7cu5h+K5PjReI/sJFTMPL4aHZ+jAn9quQl7vK8EXiL9E6G8lLiuBiVW6hjGd9At+
Z6UyGV+nCM6O3qZcyParMuLkNtWx9uT7Pcn8oTZAdKPngNhsf8+yl9qmsFkNLDC4
LKPx0+rdCjtMKn2du3krsHhG3EN9pLDrE6g5U3d6Cz83e69Y7fCuSjl31SjD91H0
bZDcM/ejYSbid3yKN4TL
=Gvgb
-----END PGP SIGNATURE-----
Merge tag 'sound-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"We've had quite busy weeks in this cycle. Looking at ALSA core, the
significant changes are a few fixes wrt timer and sequencer ioctls
that have been revealed by fuzzer recently. Other than that, ASoC
core got a few updates about DAI link handling, but these are rather
straightforward refactoring.
In drivers scene, ASoC received quite lots of new drivers in addition
to bunch of updates for still ongoing Intel Skylake support and
topology API. HD-audio gained a new HDMI/DP hotplug notification via
component. FireWire got a pile of code refactoring/updates with
SCS.1x driver integration.
More highlights are shown below.
[ NOTE: this contains also many commits for DRM. This is due to the
pull of drm stable branch into sound tree, as the base of i915 audio
component work for HD-audio. The highlights below don't contain
these DRM changes, as these are supposed to be pulled via drm tree
in anyway sooner or later. ]
Core:
- Handful fixes to harden ALSA timer and sequencer ioctls against
races reported by syzkaller fuzzer
- Irq description string can be unique to each card; only for
HD-audio for now
ASoC:
- Conversion of the array of DAI links to a list for supporting
dynamically adding and removing DAI links
- Topology API enhancements to make everything more component based
and being able to specify PCM links via topology
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production; we really need to get to the
point where that can be done
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come
- Lots of new features and cleanups for the Renesas drivers
- ANC support for WM5110
- New drivers: Imagination Technologies IPs, Atmel class D speaker,
Cirrus CS47L24 and WM1831, Dialog DA7128, Realtek RT5659 and
RT56156, Rockchip RK3036, TI PC3168A, and AMD ACP
- Rename PCM1792a driver to be generic pcm179x
HD-Audio:
- Use audio component for i915 HDMI/DP hotplug handling
- On-demand binding with i915 driver
- bdl_pos_adj parameter adjustment for Baytrail controllers
- Enable power_save_node for CX20722; this shouldn't lead to
regression, hopefully
- Kabylake HDMI/DP codec support
- Quirks for Lenovo E50-80, Dell Latitude E-series, and other Dell
machines
- A few code refactoring
FireWire:
- Lots of code cleanup and refactoring
- Integrate the support of SCS.1x devices into snd-oxfw driver;
snd-scs1x driver is obsoleted
USB-audio:
- Fix possible NULL dereference at disconnection
- A regression fix for Native Instruments devices
Misc:
- A few code cleanups of fm801 driver"
* tag 'sound-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (722 commits)
ALSA: timer: Code cleanup
ALSA: timer: Harden slave timer list handling
ALSA: hda - Add fixup for Dell Latitidue E6540
ALSA: timer: Fix race among timer ioctls
ALSA: hda - add codec support for Kabylake display audio codec
ALSA: timer: Fix double unlink of active_list
ALSA: usb-audio: Fix mixer ctl regression of Native Instrument devices
ALSA: hda - fix the headset mic detection problem for a Dell laptop
ALSA: hda - Fix white noise on Dell Latitude E5550
ALSA: hda_intel: add card number to irq description
ALSA: seq: Fix race at timer setup and close
ALSA: seq: Fix missing NULL check at remove_events ioctl
ALSA: usb-audio: Avoid calling usb_autopm_put_interface() at disconnect
ASoC: hdac_hdmi: remove unused hdac_hdmi_query_pin_connlist
ASoC: AMD: Add missing include file
ALSA: hda - Fixup inverted internal mic for Lenovo E50-80
ALSA: usb: Add native DSD support for Oppo HA-1
ASoC: Make aux_dev more like a generic component
ASoC: bcm2835: cleanup includes by ordering them alphabetically
ASoC: AMD: Manage ACP 2.x SRAM banks power
...
As illustrated by commit a3afe70b83 ("[S390] latencytop s390
support."), HAVE_LATENCYTOP_SUPPORT is defined by an architecture to
advertise an implementation of save_stack_trace_tsk.
However, as of 9212ddb5ea ("stacktrace: provide save_stack_trace_tsk()
weak alias") a dummy implementation is provided if STACKTRACE=y. Given
that LATENCYTOP already depends on STACKTRACE_SUPPORT and selects
STACKTRACE, we can remove HAVE_LATENCYTOP_SUPPORT altogether.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Helge Deller <deller@gmx.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PA-RISC doesn't have atomic instructions to modify page table entries, so it
takes spinlock in the TLB handler and modifies the page table entry
non-atomically. If you modify the page table entry without the spinlock, you
may race with TLB handler on another CPU and your modification may be lost.
Protect against that with usage of purge_tlb_start() and purge_tlb_end() which
handles the TLB spinlock.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v4.4
bulk of the changes are to clk controller drivers, though some
improvements to the core and some re-usable blocks/templates also
received some love. In this past cycle the clk maintainers developed a
good workflow for handling the common case of patch submissions
containing a new drivers, new shared Device Tree header and a new Device
Tree binding description. This requires coordination with the Device
Tree maintainers and with the architecture maintainers (typically the
arm-soc tree in our case). This explains the increase in changes to
include/dt-bindings/... and to
Documentation/devicetree/bindings/clock/... coming from the clk tree.
The same commits can be expected to come through those trees on
occasion, through the use of shared, immutable branches.
-----BEGIN PGP SIGNATURE-----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=nkGr
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk framework updates from Michael Turquette:
"The clk framework and driver changes for 4.5 look pretty typical. The
bulk of the changes are to clk controller drivers, though some
improvements to the core and some re-usable blocks/templates also
received some love.
In this past cycle the clk maintainers developed a good workflow for
handling the common case of patch submissions containing a new
drivers, new shared Device Tree header and a new Device Tree binding
description. This requires coordination with the Device Tree
maintainers and with the architecture maintainers (typically the
arm-soc tree in our case).
This explains the increase in changes to include/dt-bindings/... and
to Documentation/devicetree/bindings/clock/... coming from the clk
tree. The same commits can be expected to come through those trees on
occasion, through the use of shared, immutable branches"
* tag 'clk-for-linus-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (125 commits)
clk: remove duplicated COMMON_CLK_NXP record from clk/Kconfig
clk: fix clk-gpio.c with optional clock= DT property
clk: rockchip: fix section mismatches with new child-clocks
clk: gpio: handle error codes for of_clk_get_parent_count()
clk: gpio: fix memory leak
clk: shmobile: r8a7795: Add SATA0 clock
clk: bcm2835: Add PWM clock support
clk: bcm2835: Support for clock parent selection
clk: bcm2835: add a round up ability to the clock divisor
clk: lpc32xx: add common clock framework driver
clk: lpc18xx: add NXP specific COMMON_CLK_NXP configuration symbol
dt-bindings: clock: add NXP LPC32xx clock list for consumers
dt-bindings: clock: add description of LPC32xx USB clock controller
dt-bindings: clock: add description of LPC32xx clock controller
clk: rockchip: rk3036: include downstream muxes into fractional dividers
clk: add flag for clocks that need to be enabled on rate changes
clk: rockchip: Allow the RK3288 SPDIF clocks to change their parent
clk: rockchip: include downstream muxes into fractional dividers
clk: rockchip: handle mux dependency of fractional dividers
clk: bcm2835: Add a driver for the auxiliary peripheral clock gates.
...
By passing a non-null flag we allow fixup_user_fault to retry, which
enables userfaultfd. As during these retries we might drop the mmap_sem
we need to check if that happened and redo the complete chain of
actions.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: "Jason J. Herne" <jjherne@linux.vnet.ibm.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Eric B Munson <emunson@akamai.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Dominik Dingel <dingel@linux.vnet.ibm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During Jason's work with postcopy migration support for s390 a problem
regarding gmap faults was discovered.
The gmap code will call fixup_user_fault which will end up always in
handle_mm_fault. Till now we never cared about retries, but as the
userfaultfd code kind of relies on it. this needs some fix.
This patchset does not take care of the futex code. I will now look
closer at this.
This patch (of 2):
With the introduction of userfaultfd, kvm on s390 needs fixup_user_fault
to pass in FAULT_FLAG_ALLOW_RETRY and give feedback if during the
faulting we ever unlocked mmap_sem.
This patch brings in the logic to handle retries as well as it cleans up
the current documentation. fixup_user_fault was not having the same
semantics as filemap_fault. It never indicated if a retry happened and
so a caller wasn't able to handle that case. So we now changed the
behaviour to always retry a locked mmap_sem.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: "Jason J. Herne" <jjherne@linux.vnet.ibm.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Eric B Munson <emunson@akamai.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Dominik Dingel <dingel@linux.vnet.ibm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A dax mapping establishes a pte with _PAGE_DEVMAP set when the driver
has established a devm_memremap_pages() mapping, i.e. when the pfn_t
return from ->direct_access() has PFN_DEV and PFN_MAP set. Later, when
encountering _PAGE_DEVMAP during a page table walk we lookup and pin a
struct dev_pagemap instance to keep the result of pfn_to_page() valid
until put_page().
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A dax-huge-page mapping while it uses some thp helpers is ultimately not
a transparent huge page. The distinction is especially important in the
get_user_pages() path. pmd_devmap() is used to distinguish dax-pmds
from pmd_huge() and pmd_trans_huge() which have slightly different
semantics.
Explicitly mark the pmd_trans_huge() helpers that dax needs by adding
pmd_devmap() checks.
[kirill.shutemov@linux.intel.com: fix regression in handling mlocked pages in __split_huge_pmd()]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Similar to the conversion of vm_insert_mixed() use pfn_t in the
vmf_insert_pfn_pmd() to tag the resulting pte with _PAGE_DEVICE when the
pfn is backed by a devm_memremap_pages() mapping.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert the raw unsigned long 'pfn' argument to pfn_t for the purpose of
evaluating the PFN_MAP and PFN_DEV flags. When both are set it triggers
_PAGE_DEVMAP to be set in the resulting pte.
There are no functional changes to the gpu drivers as a result of this
conversion.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
_PAGE_DEVMAP is a hardware-unused pte bit that will later be used in the
get_user_pages() path to identify pfns backed by the dynamic allocation
established by devm_memremap_pages. Upon seeing that bit the gup path
will lookup and pin the allocation while the pages are in use.
Since the _PAGE_DEVMAP bit is > 32 it must be cast to u64 instead of a
pteval_t to allow pmd_flags() usage in the realmode boot code to build.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Take into account that the pmd_t type is a array inside a struct, so it
needs two levels of brackets to initialize. Otherwise, a usage of __pmd
generates a warning:
include/linux/mm.h:986:2: warning: missing braces around initializer [-Wmissing-braces]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch avr32/include/asm/page.h to use the common defintions for
pfn_to_page(), page_to_pfn(), and ARCH_PFN_OFFSET.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the new vmem_altmap capability to enable the pmem driver to arrange
for a struct page memmap to be established in persistent memory.
[linux@roeck-us.net: mn10300: declare __pfn_to_phys() to fix build error]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In support of providing struct page for large persistent memory
capacities, use struct vmem_altmap to change the default policy for
allocating memory for the memmap array. The default vmemmap_populate()
allocates page table storage area from the page allocator. Given
persistent memory capacities relative to DRAM it may not be feasible to
store the memmap in 'System Memory'. Instead vmem_altmap represents
pre-allocated "device pages" to satisfy vmemmap_alloc_block_buf()
requests.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the purpose of communicating the optional presence of a 'struct
page' for the pfn returned from ->direct_access(), introduce a type that
encapsulates a page-frame-number plus flags. These flags contain the
historical "page_link" encoding for a scatterlist entry, but can also
denote "device memory". Where "device memory" is a set of pfns that are
not part of the kernel's linear mapping by default, but are accessed via
the same memory controller as ram.
The motivation for this new type is large capacity persistent memory
that needs struct page entries in the 'memmap' to support 3rd party DMA
(i.e. O_DIRECT I/O with a persistent memory source/target). However,
we also need it in support of maintaining a list of mapped inodes which
need to be unmapped at driver teardown or freeze_bdev() time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Hansen <dave@sr71.net>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexey Kardashevskiy