With a recent fix to the pinctrl-cherryview driver we now have
2 drivers open-coding the parameter building / passing for calling
_REG on an ACPI handle.
Add a helper for this, so that these 2 drivers can be converted to this
helper.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In order to avoid future header hell, remove the inclusion of
proc_fs.h from acpi_bus.h. All it needs is a forward declaration of a
struct.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lkml.kernel.org/r/20200321113241.246190285@linutronix.de
There are users outside of ACPI realm which reimplementing the comparator
function to check if the given device matches to given HID and UID.
For better utilization, introduce a helper for everyone to use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We have a stub defined for the acpi_dev_get_first_match_dev() in acpi.h
for the case when CONFIG_ACPI=n.
Moreover, acpi_dev_put(), counterpart function, is already placed under
CONFIG_ACPI.
Thus, move acpi_dev_get_first_match_dev() under CONFIG_ACPI as well.
Fixes: 817b4d64da ("ACPI / utils: Introduce acpi_dev_get_first_match_dev() helper")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 5.2+ <stable@vger.kernel.org> # 5.2+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-pm:
ACPI: PM: Make acpi_sleep_state_supported() non-static
ACPI: PM: Allow transitions to D0 to occur in special cases
ACPI: PM: Avoid evaluating _PS3 on transitions from D3hot to D3cold
ACPI / sleep: Switch to use acpi_dev_get_first_match_dev()
ACPI / LPIT: Correct LPIT end address for lpit_process()
* pm-pci:
ACPI: PM: Unexport acpi_device_get_power()
PCI: PM/ACPI: Refresh all stale power state data in pci_pm_complete()
PCI / ACPI: Add _PR0 dependent devices
ACPI / PM: Introduce concept of a _PR0 dependent device
PCI / ACPI: Use cached ACPI device state to get PCI device power state
PCI: Do not poll for PME if the device is in D3cold
PCI: Add missing link delays required by the PCIe spec
PCI: PM: Replace pci_dev_keep_suspended() with two functions
PCI: PM: Avoid resuming devices in D3hot during system suspend
With some upcoming patches to save/restore the Hyper-V drivers related
states, a Linux VM running on Hyper-V will be able to hibernate. When
a Linux VM hibernates, unluckily we must disable the memory hot-add/remove
and balloon up/down capabilities in the hv_balloon driver
(drivers/hv/hv_balloon.c), because these can not really work according to
the design of the related back-end driver on the host.
By default, Hyper-V does not enable the virtual ACPI S4 state for a VM;
on recent Hyper-V hosts, the administrator is able to enable the virtual
ACPI S4 state for a VM, so we hope to use the presence of the virtual ACPI
S4 state as a hint for hv_balloon to disable the aforementioned
capabilities. In this way, hibernation will work more reliably, from the
user's perspective.
By marking acpi_sleep_state_supported() non-static, we'll be able to
implement a hv_is_hibernation_supported() API in the always-built-in
module arch/x86/hyperv/hv_init.c, and the API will be called by hv_balloon.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Using acpi_device_get_power() outside of ACPI device initialization
and ACPI sysfs is problematic due to the way in which power resources
are handled by it, so unexport it and add a paragraph explaining the
pitfalls to its kerneldoc comment.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If there are shared power resources between otherwise unrelated devices
turning them on causes the other devices sharing them to be powered up
as well. In case of PCI devices go into D0uninitialized state meaning
that if they were configured to trigger wake that configuration is lost
at this point.
For this reason introduce a concept of "_PR0 dependent device" that can
be added to any ACPI device that has power resources. The dependent
device will be included in a list of dependent devices for all power
resources returned by the ACPI device's _PR0 (assuming it has one).
Whenever a power resource having dependent devices is turned physically
on (its _ON method is called) we runtime resume all of them to allow
their driver or in case of PCI the PCI core to re-initialize the device
and its wake configuration.
This adds two functions that can be used to add and remove these
dependent devices. Note the dependent device does not necessary need
share power resources so this functionality can be used to add "software
dependencies" as well if needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Standards such as the MIPI DisCo for SoundWire 1.0 specification
assume the _ADR field is 64 bits.
_ADR is defined as an "Integer" represented as 64 bits since ACPI 2.0
released in 2002. The low levels already use _ADR as 64 bits, e.g. in
struct acpi_device_info.
This patch bumps the representation used for sysfs to 64 bits. To
avoid any compatibility/ABI issues, the printf format is only extended
to 16 characters when the actual _ADR value exceeds the 32 bit
maximum.
Example with a SoundWire device, the results show the complete
vendorID and linkID which were omitted before:
Before:
$ more /sys/bus/acpi/devices/device\:38/adr
0x5d070000
After:
$ more /sys/bus/acpi/devices/device\:38/adr
0x000010025d070000
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
[ rjw: Replace 0xFFFFFFFF with U32_MAX, clean up subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When building CONFIG_ACPI is not set
gcc warn this:
drivers/gpio/gpio-merrifield.c: In function mrfld_gpio_get_pinctrl_dev_name:
drivers/gpio/gpio-merrifield.c:388:19: error: dereferencing pointer to incomplete type struct acpi_device
put_device(&adev->dev);
^~
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d00d2109c3 ("gpio: merrifield: Convert to use acpi_dev_get_first_match_dev()")
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no more user of acpi_dev_get_first_match_name(),
which is deprecated and has no user left, so, remove it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The acpi_dev_get_first_match_name() is missing put_device() call
and thus keeping reference counting unbalanced.
In order to fix the issue introduce a new helper to convert existing users
one-by-one to a better API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
-----BEGIN PGP SIGNATURE-----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=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
It is possible to have _DSD entries where the data is compatible with
device properties format but are using different GUID for various reasons.
In addition to that there can be many such _DSD entries for a single device
such as for PCIe root port used to host a Thunderbolt hierarchy:
Scope (\_SB.PCI0.RP21)
{
Name (_DSD, Package () {
ToUUID ("6211e2c0-58a3-4af3-90e1-927a4e0c55a4"),
Package () {
Package () {"HotPlugSupportInD3", 1}
},
ToUUID ("efcc06cc-73ac-4bc3-bff0-76143807c389"),
Package () {
Package () {"ExternalFacingPort", 1},
Package () {"UID", 0 }
}
})
}
More information about these new _DSD entries can be found in:
https://docs.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports
To make these available for drivers via unified device property APIs,
modify ACPI property core so that it supports multiple _DSD entries
organized in a linked list. We also store GUID of each _DSD entry in struct
acpi_device_properties in case there is need to differentiate between
entries. The supported GUIDs are then listed in prp_guids array.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
This goes through a lot of hooks just to call arch_teardown_dma_ops.
Replace it with a direct call instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Currently the ACPI scan has special handling for serial bus slaves, in that
it makes it the responsibility of the slave device's parent to enumerate
the device.
To support other types of slave devices which require the same special
handling but where the bus is not strictly a serial bus, such as devices on
the HiSilicon LPC controller bus, rename acpi_is_serial_bus_slave() to
acpi_device_enumeration_by_parent(), so that the name can fit the wider
purpose.
Also rename the associated device flag acpi_device_flags.serial_bus_slave
to .enumeration_by_parent.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes the user wants to have device name of the match rather than
just checking if device present or not. To make life easier for such
users introduce acpi_dev_get_first_match_name() helper based on code
for acpi_dev_present().
For example, GPIO driver for Intel Merrifield needs to know the device
name of pin control to be able to apply GPIO mapping table to the proper
device.
To be more consistent with the purpose rename
struct acpi_dev_present_info -> struct acpi_dev_match_info
acpi_dev_present_cb() -> acpi_dev_match_cb()
in the utils.c file.
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On platforms (ASUS X550ZE and possibly all ASUS X series) with valid ECDT
EC but invalid DSDT EC, EC PM ops won't be invoked as ECDT EC is not an
ACPI device. Thus the following commit actually removed post-resume
acpi_ec_enable_event() invocation for such platforms, and triggered a
regression on them that after being resumed, EC (actually should be ECDT)
driver stops handling EC events:
Commit: c2b46d679b
Subject: ACPI / EC: Add PM operations to improve event handling for resume process
Notice that the root cause actually is "ECDT is not an ACPI device" rather
than "the timing of acpi_ec_enable_event() invocation", this patch fixes
this issue by enumerating ECDT EC as an ACPI device. Due to the existence
of the noirq stage, the ability of tuning the timing of
acpi_ec_enable_event() invocation is still meaningful.
This patch is a little bit different from the posted fix by moving
acpi_config_boot_ec() from acpi_ec_ecdt_start() to acpi_ec_add() to make
sure that EC event handling won't be stopped as long as the ACPI EC driver
is bound. Thus the following sequence shouldn't disable EC event handling:
unbind,suspend,resume,bind.
Fixes: c2b46d679b (ACPI / EC: Add PM operations to improve event handling for resume process)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196847
Reported-by: Luya Tshimbalanga <luya@fedoraproject.org>
Tested-by: Luya Tshimbalanga <luya@fedoraproject.org>
Cc: 4.9+ <stable@vger.kernel.org> # 4.9+
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
UART devices is expected to be enumerated by SerDev subsystem.
During ACPI scan, serial devices behind SPI, I2C or UART buses are not
enumerated, allowing them to be enumerated by their respective parents.
Rename *spi_i2c_slave* to *serial_bus_slave* as this will be used for serial
devices on serial buses (SPI, I2C or UART).
On Macs an empty ResourceTemplate is returned for uart slaves.
Instead the device properties "baud", "parity", "dataBits", "stopBits" are
provided. Add a check for "baud" in acpi_is_serial_bus_slave().
Signed-off-by: Frédéric Danis <frederic.danis.oss@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Ronald Tschalär <ronald@innovation.ch>
Tested-by: Peter Y. Chuang <peteryuchuang@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to commit db3e50f323 (device property: Get rid of struct
fwnode_handle type field), ACPI_HANDLE() inadvertently became
a GPL-only call. The call path that led to that was:
ACPI_HANDLE()
ACPI_COMPANION()
to_acpi_device_node()
is_acpi_device_node()
acpi_device_fwnode_ops
DECLARE_ACPI_FWNODE_OPS(acpi_device_fwnode_ops);
...and the new DECLARE_ACPI_FWNODE_OPS() includes
EXPORT_SYMBOL_GPL, whereas previously it was a static struct.
In order to avoid changing any of that, let's instead provide ever
so slightly better encapsulation of those struct fwnode_operations
instances. Those do not really need to be directly used in
inline function calls in header files. Simply moving two small
functions (is_acpi_device_node and is_acpi_data_node) out of
acpi_bus.h, and into a .c file, does that.
That leaves the internals of struct fwnode_operations as GPL-only
(which I think was the intent all along), but un-breaks any driver
code out there that relies on the ACPI subsystem's being (historically)
an EXPORT_SYMBOL-usable system. By that, I mean, ACPI_HANDLE() and
other basic ACPI calls were non-GPL-protected.
Also, while I'm there, remove a tiny bit of redundancy that was missed
in the earlier commit, by having is_acpi_node() use the other two
routines, instead of checking fwnode directly.
Fixes: db3e50f323 (device property: Get rid of struct fwnode_handle type field)
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Introduce fwnode operations for all of the separate types of
"firmware nodes" that can be handled by the device properties
framework and drop the type field from struct fwnode_handle
(Sakari Ailus, Arnd Bergmann).
- Make the device properties framework use const fwnode arguments
where possible (Sakari Ailus).
- Add a helper for the consolidated handling of node references
to the device properties framework (Sakari Ailus).
- Switch over the ACPI part of the device properties framework
to the new UUID API (Andy Shevchenko).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=0rnk
-----END PGP SIGNATURE-----
Merge tag 'devprop-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework updates from Rafael Wysocki:
"These introduce fwnode operations for all of the separate types of
'firmware nodes' that can be handled by the device properties
framework, make the framework use const fwnode arguments all over, add
a helper for the consolidated handling of node references and switch
over the framework to the new UUID API.
Specifics:
- Introduce fwnode operations for all of the separate types of
'firmware nodes' that can be handled by the device properties
framework and drop the type field from struct fwnode_handle (Sakari
Ailus, Arnd Bergmann).
- Make the device properties framework use const fwnode arguments
where possible (Sakari Ailus).
- Add a helper for the consolidated handling of node references to
the device properties framework (Sakari Ailus).
- Switch over the ACPI part of the device properties framework to the
new UUID API (Andy Shevchenko)"
* tag 'devprop-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: device property: Switch to use new generic UUID API
device property: export irqchip_fwnode_ops
device property: Introduce fwnode_property_get_reference_args
device property: Constify fwnode property API
device property: Constify argument to pset fwnode backend
ACPI: Constify internal fwnode arguments
ACPI: Constify acpi_bus helper functions, switch to macros
ACPI: Prepare for constifying acpi_get_next_subnode() fwnode argument
device property: Get rid of struct fwnode_handle type field
ACPI: Use IS_ERR_OR_NULL() instead of non-NULL check in is_acpi_data_node()
* acpi-ec:
ACPI / EC: Clean up EC GPE mask flag
ACPI: EC: Fix possible issues related to EC initialization order
* acpi-dma:
ACPI/IORT: Add IORT named component memory address limits
ACPI: Make acpi_dma_configure() DMA regions aware
ACPI: Introduce DMA ranges parsing
ACPI: Make acpi_dev_get_resources() method agnostic
* acpi-processor:
ACPI / processor: make function acpi_processor_check_duplicates() static
ACPI: processor: use dev_dbg() instead of dev_warn() when CPPC probe failed
* acpi-cppc:
mailbox: pcc: Drop uninformative output during boot
Some devices have limited addressing capabilities and cannot
reference the whole memory address space while carrying out DMA
operations (eg some devices with bus address bits range smaller than
system bus - which prevents them from using bus addresses that are
otherwise valid for the system).
The ACPI _DMA object allows bus devices to define the DMA window that is
actually addressable by devices that sit upstream the bus, therefore
providing a means to parse and initialize the devices DMA masks and
addressable DMA range size.
By relying on the generic ACPI kernel layer to retrieve and parse
resources, introduce ACPI core code to parse the _DMA object.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The acpi_pci_propagate_wakeup() routine is there to handle cases in
which PCI bridges (or PCIe ports) are expected to signal wakeup
for devices below them, but currently it doesn't do that correctly.
The problem is that acpi_pci_propagate_wakeup() uses
acpi_pm_set_device_wakeup() for bridges and if that routine is
called for multiple times to disable wakeup for the same device,
it will disable it on the first invocation and the next calls
will have no effect (it works analogously when called to enable
wakeup, but that is not a problem).
Now, say acpi_pci_propagate_wakeup() has been called for two
different devices under the same bridge and it has called
acpi_pm_set_device_wakeup() for that bridge each time. The
bridge is now enabled to generate wakeup signals. Next,
suppose that one of the devices below it resumes and
acpi_pci_propagate_wakeup() is called to disable wakeup for that
device. It will then call acpi_pm_set_device_wakeup() for the bridge
and that will effectively disable remote wakeup for all devices under
it even though some of them may still be suspended and remote wakeup
may be expected to work for them.
To address this (arguably theoretical) issue, allow
wakeup.enable_count under struct acpi_device to grow beyond 1 in
certain situations. In particular, allow that to happen in
acpi_pci_propagate_wakeup() when wakeup is enabled or disabled
for PCI bridges, so that wakeup is actually disabled for the
bridge when all devices under it resume and not when just one
of them does that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
To prepare for a subsequent change and make the code somewhat easier
to follow, do the following in the ACPI device wakeup handling code:
* Replace wakeup.flags.enabled under struct acpi_device with
wakeup.enable_count as that will be necessary going forward.
For now, wakeup.enable_count is not allowed to grow beyond 1,
so the current behavior is retained.
* Split acpi_device_wakeup() into acpi_device_wakeup_enable()
and acpi_device_wakeup_disable() and modify the callers of
it accordingly.
* Introduce a new acpi_wakeup_lock mutex to protect the wakeup
enabling/disabling code from races in case it is executed
more than once in parallel for the same device (which may
happen for bridges theoretically).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Constify arguments to is_acpi_node(), is_acpi_device_node(),
is_acpi_static_node() and acpi_data_node_match(). Make
to_acpi_device_node() and to_acpi_data_node() macros that can cope with
const and non-const arguments.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Instead of relying on the struct fwnode_handle type field, define
fwnode_operations structs for all separate types of fwnodes. To find out
the type, compare to the ops field to relevant ops structs.
This change has two benefits:
1. it avoids adding the type field to each and every instance of struct
fwnode_handle, thus saving memory and
2. makes the ops field the single factor that defines both the types of
the fwnode as well as defines the implementation of its operations,
decreasing the possibility of bugs when developing code dealing with
fwnode internals.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The is_acpi_data_node() function takes a struct fwnode_handle pointer as
its argument. The validity of the pointer is first checked. Extend the
check to cover error values as is done by similar is_acpi_node() and
is_acpi_device_node() functions.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-pm:
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
ACPI / sleep: EC-based wakeup from suspend-to-idle on recent systems
platform: x86: intel-hid: Wake up the system from suspend-to-idle
platform: x86: intel-vbtn: Wake up the system from suspend-to-idle
ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle
platform/x86: Add driver for ACPI INT0002 Virtual GPIO device
PCI / PM: Restore PME Enable if skipping wakeup setup
PM / sleep: Print timing information if debug is enabled
ACPI / PM: Clean up device wakeup enable/disable code
ACPI / PM: Change log level of wakeup-related message
USB / PCI / PM: Allow the PCI core to do the resume cleanup
ACPI / PM: Run wakeup notify handlers synchronously
Conflicts:
drivers/base/power/main.c
The pme_interrupt flag in struct pci_dev is set when PMEs generated
by the device are going to be signaled via root port PME interrupts.
Ironically enough, that information is only used by the code setting
up device wakeup through ACPI which returns as soon as it sees the
pme_interrupt flag set while setting up "remote runtime wakeup".
That is questionable, however, because in theory there may be PCIe
devices using out-of-band PME signaling under root ports handled
by the native PME code or devices requiring wakeup power setup to be
carried out by AML. For such devices, ACPI wakeup should be invoked
regardless of whether or not native PME signaling is used in general.
For this reason, drop the pme_interrupt flag and rework the code
using it which then allows the ACPI-based device wakeup handling
in PCI to be consolidated to use one code path for both "runtime
remote wakeup" and system wakeup (from sleep states).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Currently, there are two separate ways of handling device wakeup
settings in the ACPI core, depending on whether this is runtime
wakeup or system wakeup (from sleep states). However, after the
previous commit eliminating the run_wake ACPI device wakeup flag,
there is no difference between the two any more at the ACPI level,
so they can be combined.
For this reason, introduce acpi_pm_set_device_wakeup() to replace both
acpi_pm_device_run_wake() and acpi_pm_device_sleep_wake() and make it
check the ACPI device object's wakeup.valid flag to determine whether
or not the device can be set up to generate wakeup signals.
Also notice that zpodd_enable/disable_run_wake() only call
device_set_run_wake() because acpi_pm_device_run_wake() called
device_run_wake(), which is not done by acpi_pm_set_device_wakeup(),
so drop the now redundant device_set_run_wake() calls from there.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The run_wake flag in struct acpi_device_wakeup_flags stores the
information on whether or not the device can generate wakeup
signals at run time, but in ACPI that really is equivalent to
being able to generate wakeup signals at all.
In fact, run_wake will always be set after successful executeion of
acpi_setup_gpe_for_wake(), but if that fails, the device will not be
able to use a wakeup GPE at all, so it won't be able to wake up the
systems from sleep states too. Hence, run_wake actually means that
the device is capable of triggering wakeup and so it is equivalent
to the valid flag.
For this reason, drop run_wake from struct acpi_device_wakeup_flags
and make sure that the valid flag is only set if
acpi_setup_gpe_for_wake() has been successful.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Commit f406270bf7 ("ACPI / scan: Set the visited flag for all
enumerated devices") caused that two group of special SPI or I2C
devices do not enumerate. SPI and I2C devices are expected to be
enumerated by the SPI and I2C subsystems but change caused that
acpi_bus_attach() marks those devices with acpi_device_set_enumerated().
First group of devices are matched using Device Tree compatible property
with special _HID "PRP0001". Those devices have matched scan handler,
acpi_scan_attach_handler() retuns 1 and acpi_bus_attach() marks them
with acpi_device_set_enumerated().
Second group of devices without valid _HID such as "LNXVIDEO" have
device->pnp.type.platform_id set to zero and change again marks them
with acpi_device_set_enumerated().
Fix this by flagging the SPI and I2C devices during struct acpi_device
object initialization time and let the code in acpi_bus_attach() to go
through the device_attach() and acpi_default_enumeration() path for all
SPI and I2C devices.
Fixes: f406270bf7 (ACPI / scan: Set the visited flag for all enumerated devices)
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 4.11+ <stable@vger.kernel.org> # 4.11+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI SCI (System Control Interrupt) is set up as a wakeup IRQ
during suspend-to-idle transitions and, consequently, any events
signaled through it wake up the system from that state. However,
on some systems some of the events signaled via the ACPI SCI while
suspended to idle should not cause the system to wake up. In fact,
quite often they should just be discarded.
Arguably, systems should not resume entirely on such events, but in
order to decide which events really should cause the system to resume
and which are spurious, it is necessary to resume up to the point
when ACPI SCIs are actually handled and processed, which is after
executing dpm_resume_noirq() in the system resume path.
For this reasons, add a loop around freeze_enter() in which the
platforms can process events signaled via multiplexed IRQ lines
like the ACPI SCI and add suspend-to-idle hooks that can be
used for this purpose to struct platform_freeze_ops.
In the ACPI case, the ->wake hook is used for checking if the SCI
has triggered while suspended and deferring the interrupt-induced
system wakeup until the events signaled through it are actually
processed sufficiently to decide whether or not the system should
resume. In turn, the ->sync hook allows all of the relevant event
queues to be flushed so as to prevent events from being missed due
to race conditions.
In addition to that, some ACPI code processing wakeup events needs
to be modified to use the "hard" version of wakeup triggers, so that
it will cause a system resume to happen on device-induced wakeup
events even if the "soft" mechanism to prevent the system from
suspending is not enabled. However, to preserve the existing
behavior with respect to suspend-to-RAM, this only is done in
the suspend-to-idle case and only if an SCI has occurred while
suspended.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The work functions provided by the users of acpi_add_pm_notifier()
should be run synchronously before re-enabling the wakeup GPE in
case they are used to clear the status and/or disable the wakeup
signaling at the source. Otherwise, which is the case currently in
the PCI bus type code, the same wakeup event may be signaled for
multiple times while the execution of the work function in response
to it has already been queued up.
Fortunately, acpi_add_pm_notifier() is only used by PCI and by
ACPI device PM code internally, so the change is relatively
straightforward to make.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
acpi_evaluate_dsm() and friends take a pointer to a raw buffer of 16
bytes. Instead we convert them to use guid_t type. At the same time we
convert current users.
acpi_str_to_uuid() becomes useless after the conversion and it's safe to
get rid of it.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
- Update the ACPICA code in the kernel to upstream revision
20170303 which includes:
* Minor fixes and improvements in the core code (Bob Moore,
Seunghun Han).
* Debugger fixes (Colin Ian King, Lv Zheng).
* Compiler/disassembler improvements (Bob Moore, David Box,
Lv Zheng).
* Build-related update (Lv Zheng).
- Add new device IDs and platform-related information to the
ACPI drivers for Intel (LPSS) and AMD (APD) SoCs (Hanjun Guo,
Hans de Goede).
- Make it possible to quirk ACPI-enumerated devices as "always
present" on platforms where they are incorrectly reported as not
present by the AML and add the INT0002 device ID to the list of
"always present" devices (Hans de Goede).
- Fix the register information in the xpower PMIC driver and add
comments to map the registers to symbols used by AML to it
(Hans de Goede).
- Move the code turning off unused ACPI power resources during
system resume to a point after all devices have been resumed
to avoid issues with power resources that do not behave as
expected (Hans de Goede).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ytsi
-----END PGP SIGNATURE-----
Merge tag 'acpi-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20170303 which adds a few minor fixes and improvements, update ACPI
SoC drivers with new device IDs, platform-related information and
similar, fix the register information in the xpower PMIC driver,
introduce a concept of "always present" devices to the ACPI device
enumeration code and use it to fix a problem with one platform, and
fix a system resume issue related to power resources.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20170303
which includes:
* Minor fixes and improvements in the core code (Bob Moore,
Seunghun Han).
* Debugger fixes (Colin Ian King, Lv Zheng).
* Compiler/disassembler improvements (Bob Moore, David Box, Lv
Zheng).
* Build-related update (Lv Zheng).
- Add new device IDs and platform-related information to the ACPI
drivers for Intel (LPSS) and AMD (APD) SoCs (Hanjun Guo, Hans de
Goede).
- Make it possible to quirk ACPI-enumerated devices as "always
present" on platforms where they are incorrectly reported as not
present by the AML and add the INT0002 device ID to the list of
"always present" devices (Hans de Goede).
- Fix the register information in the xpower PMIC driver and add
comments to map the registers to symbols used by AML to it (Hans de
Goede).
- Move the code turning off unused ACPI power resources during system
resume to a point after all devices have been resumed to avoid
issues with power resources that do not behave as expected (Hans de
Goede)"
* tag 'acpi-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (22 commits)
ACPI / power: Delay turning off unused power resources after suspend
ACPI / PMIC: xpower: Fix power_table addresses
ACPI / LPSS: Call pwm_add_table() for Bay Trail PWM device
ACPICA: Update version to 20170303
ACPICA: iasl: add ASL conversion tool
ACPICA: Local cache support: Allow small cache objects
ACPICA: Disassembler: Do not unconditionally remove temporary names
ACPICA: iasl: Fix IORT SMMU GSI disassembling
ACPICA: Cleanup AML opcode definitions, no functional change
ACPICA: Debugger: Add interpreter blocking mark for single-step mode
ACPICA: debugger: fix memory leak on Pathname
ACPICA: Update for automatic repair code for objects returned by evaluate_object
ACPICA: Namespace: fix operand cache leak
ACPICA: Fix several incorrect invocations of ACPICA return macro
ACPICA: Fix a module for excessive debug output
ACPICA: Update some function headers, no funtional change
ACPICA: Disassembler: Enhance resource descriptor detection
i2c: designware: Add ACPI HID for Hisilicon Hip07/08 I2C controller
ACPI / APD: Add clock frequency for Hisilicon Hip07/08 I2C controller
ACPI / bus: Add INT0002 to list of always-present devices
...
This includes:
* Some code optimizations for the Intel VT-d driver
* Code to switch off a previously enabled Intel IOMMU
* Support for 'struct iommu_device' for OMAP, Rockchip and
Mediatek IOMMUs
* Some header optimizations for IOMMU core code headers and a
few fixes that became necessary in other parts of the kernel
because of that
* ACPI/IORT updates and fixes
* Some Exynos IOMMU optimizations
* Code updates for the IOMMU dma-api code to bring it closer to
use per-cpu iova caches
* New command-line option to set default domain type allocated
by the iommu core code
* Another command line option to allow the Intel IOMMU switched
off in a tboot environment
* ARM/SMMU: TLB sync optimisations for SMMUv2, Support for using
an IDENTITY domain in conjunction with DMA ops, Support for
SMR masking, Support for 16-bit ASIDs (was previously broken)
* Various other small fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3aE8
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- code optimizations for the Intel VT-d driver
- ability to switch off a previously enabled Intel IOMMU
- support for 'struct iommu_device' for OMAP, Rockchip and Mediatek
IOMMUs
- header optimizations for IOMMU core code headers and a few fixes that
became necessary in other parts of the kernel because of that
- ACPI/IORT updates and fixes
- Exynos IOMMU optimizations
- updates for the IOMMU dma-api code to bring it closer to use per-cpu
iova caches
- new command-line option to set default domain type allocated by the
iommu core code
- another command line option to allow the Intel IOMMU switched off in
a tboot environment
- ARM/SMMU: TLB sync optimisations for SMMUv2, Support for using an
IDENTITY domain in conjunction with DMA ops, Support for SMR masking,
Support for 16-bit ASIDs (was previously broken)
- various other small fixes and improvements
* tag 'iommu-updates-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (63 commits)
soc/qbman: Move dma-mapping.h include to qman_priv.h
soc/qbman: Fix implicit header dependency now causing build fails
iommu: Remove trace-events include from iommu.h
iommu: Remove pci.h include from trace/events/iommu.h
arm: dma-mapping: Don't override dma_ops in arch_setup_dma_ops()
ACPI/IORT: Fix CONFIG_IOMMU_API dependency
iommu/vt-d: Don't print the failure message when booting non-kdump kernel
iommu: Move report_iommu_fault() to iommu.c
iommu: Include device.h in iommu.h
x86, iommu/vt-d: Add an option to disable Intel IOMMU force on
iommu/arm-smmu: Return IOVA in iova_to_phys when SMMU is bypassed
iommu/arm-smmu: Correct sid to mask
iommu/amd: Fix incorrect error handling in amd_iommu_bind_pasid()
iommu: Make iommu_bus_notifier return NOTIFY_DONE rather than error code
omap3isp: Remove iommu_group related code
iommu/omap: Add iommu-group support
iommu/omap: Make use of 'struct iommu_device'
iommu/omap: Store iommu_dev pointer in arch_data
iommu/omap: Move data structures to omap-iommu.h
iommu/omap: Drop legacy-style device support
...
- Extend the ACPI _DSD properties code and the generic device
properties framework to support the concept of remote endponts
(Mika Westerberg, Sakari Ailus).
- Document the support for ports and endpoints in _DSD properties
and extend the generic device properties framework to make it
more suitable for the handling of ports and endpoints (Sakari
Ailus).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ihme
-----END PGP SIGNATURE-----
Merge tag 'devprop-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull generic device properties framework updates from Rafael Wysocki:
"These add support for the ports and endpoints concepts, based on the
existing DT support for them, to the generic device properties
framework and update the ACPI _DSD properties code to recognize ports
and endpoints accordingly.
Specifics:
- Extend the ACPI _DSD properties code and the generic device
properties framework to support the concept of remote endponts
(Mika Westerberg, Sakari Ailus).
- Document the support for ports and endpoints in _DSD properties and
extend the generic device properties framework to make it more
suitable for the handling of ports and endpoints (Sakari Ailus)"
* tag 'devprop-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: Read strings using string array reading functions
device property: fwnode_property_read_string_array() returns nr of strings
device property: Fix reading pset strings using array access functions
device property: fwnode_property_read_string_array() may return -EILSEQ
ACPI / DSD: Document references, ports and endpoints
device property: Add fwnode_get_next_parent()
device property: Add support for fwnode endpoints
device property: Make dev_fwnode() public
of: Add of_fwnode_handle() to convert device nodes to fwnode_handle
device property: Add fwnode_handle_get()
device property: Add support for remote endpoints
ACPI / property: Add support for remote endpoints
device property: Add fwnode_get_named_child_node()
ACPI / property: Add fwnode_get_next_child_node()
device property: Add fwnode_get_parent()
ACPI / property: Add possiblity to retrieve parent firmware node
Several Bay / Cherry Trail devices (all of which ship with Windows 10) hide
the LPSS PWM controller in ACPI, typically the _STA method looks like this:
Method (_STA, 0, NotSerialized) // _STA: Status
{
If (OSID == One)
{
Return (Zero)
}
Return (0x0F)
}
Where OSID is some dark magic seen in all Cherry Trail ACPI tables making
the machine behave differently depending on which OS it *thinks* it is
booting, this gets set in a number of ways which we cannot control, on
some newer machines it simple hardcoded to "One" aka win10.
This causes the PWM controller to get hidden, which means Linux cannot
control the backlight level on cht based tablets / laptops.
Since loading the driver for this does no harm (the only in kernel user
of it is the i915 driver, which will only uses it when it needs it), this
commit makes acpi_bus_get_status() always set status to ACPI_STA_DEFAULT
for the LPSS PWM device, fixing the lack of backlight control.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[ rjw: Rename the new file to utils.c ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is an equivalent to the DT's handling of the iommu master's probe
with deferred probing when the corrsponding iommu is not probed yet.
The lack of a registered IOMMU can be caused by the lack of a driver for
the IOMMU, the IOMMU device probe not having been performed yet, having
been deferred, or having failed.
The first case occurs when the firmware describes the bus master and
IOMMU topology correctly but no device driver exists for the IOMMU yet
or the device driver has not been compiled in. Return NULL, the caller
will configure the device without an IOMMU.
The second and third cases are handled by deferring the probe of the bus
master device which will eventually get reprobed after the IOMMU.
The last case is currently handled by deferring the probe of the bus
master device as well. A mechanism to either configure the bus master
device without an IOMMU or to fail the bus master device probe depending
on whether the IOMMU is optional or mandatory would be a good
enhancement.
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
[Lorenzo: Added fixes for dma_coherent_mask overflow, acpi_dma_configure
called multiple times for same device]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
acpi_dev_found just iterates over all ACPI-ids and sees if one matches.
This means that it will return true for devices which are in the DSDT
but disabled (their _STA method returns 0).
For some drivers it is useful to be able to check if a certain HID
is not only present in the namespace, but also actually present as in
acpi_device_is_present() will return true for the device. For example
because if a certain device is present then the driver will want to use
an extcon or IIO ADC channel provided by that device.
This commit adds a new acpi_dev_present helper which drivers can use
to this end.
Like acpi_dev_found, acpi_dev_present take a HID as argument, but
it also has 2 extra optional arguments to only check for an ACPI
device with a specific UID and/or HRV value. This makes it more
generic and allows it to replace custom code doing similar checks
in several places.
Arguably acpi_dev_present is what acpi_dev_found should have been, but
there are too many users to just change acpi_dev_found without the risk
of breaking something.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes it is useful to be able to navigate firmware node hierarchy
upwards toward parent nodes. ACPI device nodes are pretty much already
supported because ACPICA provides acpi_get_parent(). ACPI data nodes,
however, are all below the same parent ACPI device. Their hierarchy is
created by "linking" each other using references in the value field.
Add parent pointer to the parent data node while we create them so it is
easy to navigate the hierarchy backwards. We use this parent pointer in a
new function acpi_node_get_parent() that is able to extract parent of both
ACPI firmware node types.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When using devicetree stuff like i2c_client.name or spi_device.modalias
is initialized to the first DT compatible id with the vendor prefix
stripped. Since some drivers rely on this try to replicate it when using
ACPI with DT ids.
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On DT based systems, the of_dma_configure() API implements DMA
configuration for a given device. On ACPI systems an API equivalent to
of_dma_configure() is missing which implies that it is currently not
possible to set-up DMA operations for devices through the ACPI generic
kernel layer.
This patch fills the gap by introducing acpi_dma_configure/deconfigure()
calls that for now are just wrappers around arch_setup_dma_ops() and
arch_teardown_dma_ops() and also updates ACPI and PCI core code to use
the newly introduced acpi_dma_configure/acpi_dma_deconfigure functions.
Since acpi_dma_configure() is used to configure DMA operations, the
function initializes the dma/coherent_dma masks to sane default values
if the current masks are uninitialized (also to keep the default values
consistent with DT systems) to make sure the device has a complete
default DMA set-up.
The DMA range size passed to arch_setup_dma_ops() is sized according
to the device coherent_dma_mask (starting at address 0x0), mirroring the
DT probing path behaviour when a dma-ranges property is not provided
for the device being probed; this changes the current arch_setup_dma_ops()
call parameters in the ACPI probing case, but since arch_setup_dma_ops()
is a NOP on all architectures but ARM/ARM64 this patch does not change
the current kernel behaviour on them.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> [pci]
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Tomasz Nowicki <tn@semihalf.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>