The TLL channel enable code searches for the wrong mask, and
could end up enabling the wrong port. Fix this.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the ohci-omap3 driver, not ehci-omap. Correct this
obvious typo.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Page size for transaction descriptors for CI13XXX has nothing
common with page size from MM. Using platform and configuration
specific PAGE_SIZE is wrong.
Signed-off-by: Artem Leonenko <tikkeri@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CI13xxx UDC driver doesn't call complete() callback for requests
with flag no_interrupt set. Thus gadget drivers (like g_ether) are
never notifed about successfully (or not) transmitted requests. As
a result in case of g_ether and queued request with no_interrupt=1
fields g_ether is never notifed about sent packets and TX stalls.
Solution: treat no_interrupt flag like all other UDC drivers do and
call complete() callback for all requests.
Signed-off-by: Artem Leonenko <tikkeri@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is one nasty scenario when CI13xxx driver fails:
a) two or more rx requests are queued (g_ether does that)
b) rx request completed, interrupt fires and ci13xxx dequeues rq
c) request complete() callback gets called and in turn it calls ep_queue()
c1) in ep_queue() request gets added to the TAIL of the rx queue list
d) ep gets primed with rq from (b)
e) interrupt fires
f) request gets popped from queue head for hw dequeue
G) requets from queue head wasn't enqueued
g1) isr_tr_complete_low() doesn't
enqueue more requests and it doesn't prime EP,
rx traffic stalls
Solution:
a) enque queued requests ASAP, i.e. before calling complete() callback.
b) don't HW enqueue and prime endpoint with recently added request and
use the oldest request in the queue.
Fixed issues:
a) ep_queue() may return an error code despite request was successfully
added to the queue (if _hardware_enqueue() fails)
b) Added requests are always processed in LIFO order, even if they are
added in complete() callback
c) Finally more than two and more queued requests are processed consistently,
even if they were added in complete() callback
The fix was successfully tested on MIPS based SoC with 4KEc CPU core and
CI13612 USB core. Board successfully boots with NFS root using g_ether
on ci13xxx udc.
Signed-off-by: Artem Leonenko <tikkeri@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Built-in gadget drivers have NULL-ifed unbind() function. Checking
whether unbind() is NULL will never let any compiled into kernel
driver attach.
Signed-off-by: Artem Leonenko <tikkeri@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
This reverts commit 32d5dc9520.
Needed to properly merge the musb changes that are in the
usb-next branch into Linus's tree.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 1e393c6eec.
Needed to properly merge the musb changes that are in the
usb-next branch into Linus's tree.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If swap is on a UAS device, we could recurse into the driver by using
GFP_KERNEL. Using GFP_NOIO ensures we won't.
Reported-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While all existing UAS devices use alternate interface 1, this is not
guaranteed, and it has caused confusion with people trying to bind the
uas driver to non-uas devices.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The spec calls this the status pipe. While it is used to receive sense IUs,
it is also used to receive other IUs, so this can be confusing.
Reported-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The IUs are not being fully initialised by the driver (due to the reserved
space). Since we should be zeroing reserved fields, use kzalloc to do
it for us.
Reported-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a comment to the Sense IU data structure that it's also used for Read
Ready and Write Ready. Remove the 'service response' element since it's
gone from the current draft (04).
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (75 commits)
pppoe.c: Fix kernel panic caused by __pppoe_xmit
WAN: Fix a TX IRQ causing BUG() in PC300 and PCI200SYN drivers.
bnx2x: Advance a version number to 1.60.01-0
bnx2x: Fixed a compilation warning
bnx2x: LSO code was broken on BE platforms
qlge: Fix deadlock when cancelling worker.
net: fix skb_defer_rx_timestamp()
cxgb4vf: Ingress Queue Entry Size needs to be 64 bytes
phy: add the IC+ IP1001 driver
atm: correct sysfs 'device' link creation and parent relationships
MAINTAINERS: remove me from tulip
SCTP: Fix SCTP_SET_PEER_PRIMARY_ADDR to accpet v4mapped address
enic: Bug Fix: Pass napi reference to the isr that services receive queue
ipv6: fix nl group when advertising a new link
connector: add module alias
net: Document the kernel_recvmsg() function
r8169: Fix runtime power management
hso: IP checksuming doesn't work on GE0301 option cards
xfrm: Fix xfrm_state_migrate leak
net: Convert netpoll blocking api in bonding driver to be a counter
...
musb_core.c #include's a bunch of ARM and DaVinci specific headers, goodness
knows why -- it happily compiles without them...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The ATM subsystem was incorrectly creating the 'device' link for ATM
nodes in sysfs. This led to incorrect device/parent relationships
exposed by sysfs and udev. Instead of rolling the 'device' link by hand
in the generic ATM code, pass each ATM driver's bus device down to the
sysfs code and let sysfs do this stuff correctly.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches makes possible to use composite framework and f_ncm
NCM function driver to build a standalone NCM gadget device.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial submittion of NCM link function driver.
The driver's logic is based on f_ecm driver and does not
use most of the NCM advantages like frame grouping and alignment.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
NCM is a Network Control Model, subclass of USB CDC class,
specification is available at http://www.usb.org/developers/devclass_docs
This patch makes possible for u_ether to use multiply of wMaxPacketSize
predefined size transfers without ZLP (Zero Length Packet), required
by NCM spec.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes an issue where the driver does not handle out data in
setup transactions.
The per endpoint cached status register is cleared in the
pch_udc_svc_control_out function. When there is out data available the
function pch_udc_svc_data_out is called which tries to pick it up the
status, which now is cleared to 0. When the status is 0, the function
doesn't start reading the data from the FIFO.
There is a second bug in all this, pch_udc_svc_data_out takes the
endpoint number (0 for EP0), while pch_udc_svc_control_out passes the
endpoint index (1 for EP0). Effectively pch_udc_svc_data_out picks up
the wrong internal ep structure.
This patch makes sure to put back the cached status and pass the
endpoint number rather than index when calling pch_udc_svc_data_out.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Building pch_udc in linux-next fails, this patch fixes the a compile
error:
drivers/usb/gadget/pch_udc.c: In function ‘usb_gadget_register_driver’:
drivers/usb/gadget/pch_udc.c:2645: error: ‘struct usb_gadget_driver’ has no member named ‘bind’
drivers/usb/gadget/pch_udc.c:2664: error: ‘struct usb_gadget_driver’ has no member named ‘bind’
And a couple of compiler warnings and checkpatch warnings.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OTG driver takes care of putting hardware in low power mode. Hence
not registered for any runtime PM callbacks.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The actual suspend/resume work is delegated to bus glue driver, which
is responsible for putting hardware in low power mode.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MSM SoC has chipidea USB controller. So use ci13xxx_udc core.
This driver depends on transceiver driver for clock control,
PHY initialization, VBUS detection. Register for notify_event
callback to perform MSM specific quirks after controller is reset
and stopped.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Introduces ci13xxx_udc_driver struct for bus glue drivers to hint
ci13xxx_udc core about their special requirements. The flags include
avoiding hardware register access when controller is not in peripheral
mode, enabling pull-up upon VBUS, disabling streaming mode and dependency
on transceiver driver.
Initialize gadget_ops in udc_probe so that transceiver can notify VBUS
presence even when no gadget driver is bounded.
A notify_event callback is embedded in the same struct. This patch implements
two events called CONTROLLER_RESET_EVENT and CONTROLLER_STOPPED_EVENT to
notify the bus glue driver after resetting and stopping the controller for
performing SoC specific quirks.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dma_alloc_coherent() which is internally called by dma_pool_alloc()
flags a warning if device's coherent DMA mask. Hence initialize
gadget device's coherent DMA mask to it's parent mask.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dma_pool_alloc() require sleeping context when called with GFP_KERNEL
argument. Hence release the spin lock before calling dma_pool_alloc().
usb_ep_alloc_request can also be called with non-atomic GFP flags. Hence
get rid off spin lock while allocation request memory.
Use GFP_ATOMIC flag for allocating request for ep0 in interrupt handler.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move PCI bus code from ci13xxx_udc to a new file ci13xxx_pci. SoC's
which has MIPS USB core can include the ci13xxx_udc and keep bus glue
code in their respective gadget controller drivers.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implement runtime and system pm ops to put hardware into low power
mode (LPM). As part of LPM, USB clocks are turned off, PHY is put
into suspend state and PHY comparators are turned off if VBUS/Id
notifications are not required from PHY.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enable runtime PM and mark no_callbacks flag. OTG device, parent of
HCD takes care of putting hardware into low power mode. Adjust port
power wakeup flags during system suspend and resume.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for EHCI compliant HSUSB Host controller found
on MSM chips. The root hub has a single port and TT is built into it.
This driver depends on OTG driver for PHY initialization, clock
management and powering up VBUS.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver implements PHY initialization, clock management, ULPI IO ops
and simple OTG state machine to kick host/peripheral based on Id/VBUS
line status. VBUS/Id lines are tied to a reference voltage on some boards.
Hence provide debugfs interface to select host/peripheral mode.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When ASPM PM Feature is enabled on UMI link, devices that use ISOC stream of
data transfer may be exposed to longer latency causing less than optimal per-
formance of the device. The longer latencies are normal and are due to link
wake time coming out of low power state which happens frequently to save
power when the link is not active.
The following code will make exception for certain features of ASPM to be by
passed and keep the logic normal state only when the ISOC device is connected
and active. This change will allow the device to run at optimal performance
yet minimize the impact on overall power savings.
Signed-off-by: Alex He <alex.he@amd.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a build failure[1] by adding the missing uaccess.h needed
for copy_from_user and copy_to_user
References:
http://kisskb.ellerman.id.au/kisskb/buildresult/3607218/
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
IS_ERR() already implies unlikely(), so it can be omitted here.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 06c3859 (usb: gadget/imx-udc: remove usage of deprecated symbol
USBD_INT0) was a bit precipitant because the name used instead didn't
match the usual naming scheme for irqs on arm/imx. I renamed the irq to
the right name in e083000 (ARM: imx: dynamically allocate imx_udc
device) when 06c3859 didn't hit Linus' tree, so I missed to add a
compat #define.
This patch allows compiling imx_udc.c with and without e083000.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Annotate whci_hcd_id_table as '__used' to fix following warning:
CC drivers/usb/host/whci/hcd.o
drivers/usb/host/whci/hcd.c:359: warning: ‘whci_hcd_id_table’ defined but not used
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OMAP4430 supports UTMI and ULPI types of transceiver interface.
In UTMI mode: The PHY is embedded within OMAP4430. The transceiver functionality
is split between the twl6030 PMIC chip and OMAP4430. The VBUS, ID pin
sensing and OTG SRP generation part is integrated in TWL6030 and UTMI PHY
functionality is embedded within the OMAP4430.
There is no direct interactions between the MUSB controller and TWL6030
chip to communicate the session-valid, session-end and ID-GND events.
It has to be done through a software by setting/resetting bits in
one of the control module register of OMAP4430 which in turn toggles
the appropriate signals to MUSB controller.
musb driver is register for blocking notifications from the transceiver
driver to get the event notifications for connect/disconnect and ID-GND.
Based on these events call the transceiver init/shutdown function to
configure the transceiver to toggle the VBUS valid, session end and ID_GND
signals to musb and power on/off the internal PHY.
For ID_GND event notifications, toggle the ID_GND signal and then wait for
musb to be configured as "A" device, and then call the transceiver function
to set the VBUS.
In OTG mode and musb as a host, When the Micro A connector used, VBUS is turned on
and session bit set. When the device is connected, enumeration goes through.
When the device disconnected from the other end of the connector(ID is still grounded),
link will detect the disconnect and end the session. When the device is connected back,
there are no events generated in the TWL6030-usb, and link is already down.
So the device is not detected. Removed the session bit disable code which
will recognize the connect of the device.
Limitation: In OTG host mode, if device is connected during boot, it does not get
detected. If disconnect and connect it back or connect after boot only it works.
Fix for this, I will submit seperate patch later.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Selecting the twl6030-usb for OMAP4430SDP and OMAP4PANDA boards and
adding OMAP4 internal phy code for compilation
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added the TWL6030-usb transceiver option in the Kconfig
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adding the twl6030-usb transceiver support for OMAP4 musb driver.
OMAP4 supports 2 types of transceiver interface.
1. UTMI: The PHY is embedded within OMAP4. The transceiver functionality
is split between the twl6030 PMIC chip and OMAP4430. The VBUS, ID pin
sensing and OTG SRP generation part is integrated in TWL6030 and UTMI PHY
functionality is embedded within the OMAP4430.
There is no direct interactions between the MUSB controller and TWL6030
chip to communicate the session-valid, session-end and ID-GND events.
It has to be done through a software by setting/resetting bits in
one of the control module register of OMAP4430 which in turn toggles
the appropriate signals to MUSB controller.
The internal transceiver has functional clocks and
powerdown bits to powerdown the PHY for power saving.
Since there is no option available for having 2 transceiver drivers
for one USB controller, internal PHY specific APIs are passed through
plaform_data function pointers to use in the twl6030-usb transceiver
driver.
2. ULPI interface is provided for off-chip transceivers.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Initial support for u8500 and u5500 platform.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 4814ced511 (OMAP:
control: move plat-omap/control.h to mach-omap2/control.h)
moved <plat/control.h> to another location, preventing
drivers from accessing it, so we need to pass function
pointers from arch code to be able to talk to internal
PHY on AM35x.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
all glue layers are now fully moved to the
new setup. We are now using dev_pm_ops to
implement suspend/resume functionality and
thus, musb_platform_suspend/resume has become
deprecated and useless.
This patch drops those function pointers and
its uses.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Anand Gadiyar