Cosmetic patch removing extra whitespaces when writing the flow_table
entries
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as TAILDESCR_PTR is written, DMA transfers might start.
Let's ensure we are ready to receive DMA IRQ's before doing that.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows custom setup of IRQ coalescing for platforms using legacy
platform_device. The irq timeout and count parameters can be used for
tuning cpu load vs. latency.
I have maintained the 0x00000400 bit in TX_CHNL_CTRL. It is specified as
unused in the documentation I have available. It does not make any
difference in the hardware I have available, so it is left in to not risk
breaking other platforms where it might be used.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use usleep_range() to avoid problems with msleep() actually sleeping
much longer than expected.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we are actually using a BD for both the skb and each frag contained in
it, the oldest TX BD would be overwritten when there was exactly one BD
less than needed.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unmap the actual buffer length, not the amount of data received, avoiding
resource exhaustion of swiotlb (seen on x86_64 platform).
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indirect register access goes through a DCR bus bridge, which
allows only one outstanding transaction. And to make matters
worse, each TEMAC IP block contains two Ethernet interfaces, and
although they seem to have separate registers for indirect access,
they actually share the registers. Or to be more specific, MSW, LSW
and CTL registers are physically shared between Ethernet interfaces
in same TEMAC IP, with RDY register being (almost) specificic to
the Ethernet interface. The 0x10000 bit in RDY reflects combined
bus ready state though.
So we need to take care to synchronize not only within a single
device, but also between devices in same TEMAC IP.
This commit allows to do that with legacy platform devices.
For OF devices, the xlnx,compound parent of the temac node should be
used to find siblings, and setup a shared indirect_mutex between them.
I will leave this work to somebody else, as I don't have hardware to
test that. No regression is introduced by that, as before this commit
using two Ethernet interfaces in same TEMAC block is simply broken.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With little-endian and 64-bit support in place, the ll_temac driver can
now be used on x86 and x86_64 platforms.
And while at it, enable COMPILE_TEST also.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both TEMAC and SDMA is big-endian, so make sure that all values in SDMA
buffer descriptors (cmdac_bd) are handled as big-endian, independent of the
host endianness. With all currently supported platforms being big-endian,
this change does not make a change for any of them.
Note, when using app3 and app4 for piggybacking skb pointers there is no
need to care about endianness, as neither TEMAC nor SDMA access app3 and
app4 in TX buffer descriptors.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the powerpc specific MMIO register access functions with the
generic big-endian mmio access functions, and add support for
little-endian access depending on configuration.
Big-endian access is maintained as the default, but little-endian can
be configured in device-tree binding or in platform data.
The temac_ior()/temac_iow() functions are replaced with macro wrappers
to avoid modifying existing code more than necessary.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of buffer descriptor APP4 field (32-bit) for storing skb pointer
obviously does not work on 64-bit platforms.
As APP3 is also unused, we can use that to store the other half of 64-bit
pointer values.
Contrary to what is hinted at in commit message of commit 15bfe05c8d
("net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit")
there are no other pointers stored in cdmac_bd.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support initialization with platdata, so the driver can be used on
non-device-tree platforms.
For currently supported device-tree platforms, the driver should behave
as before.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a side effect, a few error cases are fixed.
If of_iomap() of sdma_regs failed, no error code was returned. Fixed to
return -ENOMEM similar to of_iomap() fail of regs.
If sysfs_create_group() or register_netdev() failed, lp->phy_node was not
released.
Finally, the order in remove function is corrected to be reverse order
of what is done in probe, i.e. calling temac_mdio_teardown() last, so we
unregister the netdev that most likely is using the mdio_bus first.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix inconsistent IS_ERR and PTR_ERR in cpsw_probe,
The proper pointer to use is clk instead of mode.
This issue was detected with the help of Coccinelle.
Fixes: 83a8471ba2 ("net: ethernet: ti: cpsw: refactor probe to group common hw initialization")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/sfc/mcdi_port.c: In function ‘efx_mcdi_phy_decode_link’:
./include/linux/compiler.h:77:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:125:2: note: in expansion of macro ‘unlikely’
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/net/ethernet/sfc/mcdi_port.c:344:3: note: in expansion of macro ‘WARN_ON’
WARN_ON(1);
^~~~~~~
drivers/net/ethernet/sfc/mcdi_port.c:345:2: note: here
case MC_CMD_FCNTL_OFF:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some device ids were never released and does not exist.
Cleanup these.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA counters are 64 bit and we can fetch that to reduce
counter overflow, espesially on byte counters.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aq_nic_update_ndev_stats pushes statistics to ndev->stats from
system interface. This is not always good because it counts packets/bytes
before any of rx filters (including mac filter).
Its better to report the packet/bytes statistics from DMA
counters which gives actual values of data transferred over pci.
System level stats is still available via ethtool.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This improves ethtool -S usage, where stats are now actual
on each request. Before that stats only were updated at service
timer period.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Service timer callback fetches statistics from FW and that may cause
a long delay in error cases. We also now need to use fw mutex
to prevent concurrent access to FW, thus - extract that logic
from timer callback into the job in the separate work queue.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of FW operations could be invoked simultaneously,
from f.e. ethtool context and from service service activity work.
Here we introduce a fw mutex to secure and serialize access
to FW logic.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typo in msi code. No much impact though.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve for better readability
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original code detected link only after 1 sec is passed after up.
Here we replace this with direct service callback which updates
link status immediately
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we define and request an extra interrupt line,
assign it on link isr handler and restructure abit aq_pci code
to better support that.
We also remove logic for using different timer intervals
depending on link state, since thats now useless.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need this to schedule link interrupt handling and
various service tasks.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define link interrupt handler
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare macroes and nic fields to support link interrupt
handling
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for hwmon api to fetch out chip temperature
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ability to read the chip temperature from memory
via hwmon interface
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Neil who reported the issue leading to this
workaround, the workaround is no longer needed since
version 5.0. So let's remove it.
This was the bug report leading to the workaround:
https://bugzilla.kernel.org/show_bug.cgi?id=201081
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Neil MacLeod <neil@nmacleod.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fortunately in one place there's a comment explaining what toggling
this bit does. So let's create a helper for it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers rtl_eri_set_bits and rtl_eri_clear_bits to improve
readability of the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In basically all eri function calls the type argument is ERIAR_EXGMAC.
Therefore make it the default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-04-28
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Introduce BPF socket local storage map so that BPF programs can store
private data they associate with a socket (instead of e.g. separate hash
table), from Martin.
2) Add support for bpftool to dump BTF types. This is done through a new
`bpftool btf dump` sub-command, from Andrii.
3) Enable BPF-based flow dissector for skb-less eth_get_headlen() calls which
was currently not supported since skb was used to lookup netns, from Stanislav.
4) Add an opt-in interface for tracepoints to expose a writable context
for attached BPF programs, used here for NBD sockets, from Matt.
5) BPF xadd related arm64 JIT fixes and scalability improvements, from Daniel.
6) Change the skb->protocol for bpf_skb_adjust_room() helper in order to
support tunnels such as sit. Add selftests as well, from Willem.
7) Various smaller misc fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During driver unload, hash/TCAM filter deletion doesn't wait for
completion.This patch deletes all the filters with completion before
clearing the resources.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibmvnic driver currently uses the same fixed name when using
request_irq, this makes it hard to parse when multiple VNIC devices are
available at the same time. This patch adds the unit_address as the device
identification along with an id for each queue.
The original idea was to use the interface name as an identifier, but it
is not feasible given these requests happen at adapter probe, and at this
point netdev is not yet registered so it doesn't have the proper name
assigned to it.
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.ibm.com>
Reviewed-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Reviewed-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to add support for a switchdev based cpsw driver,
move common ethtool functions to separate cpsw-ethtool.c file so that they
can be used across both drivers. It will simplify CPSW driver code
maintenance also.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch CPSW driver to use the new MAC SL API.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC SL submodule has a lot of common functions between many of TI SoCs
AM335x/AM437x/DRA7(AM57xx), Keystone 2 66AK2HK/E/L/G and K3 AM654, but
there are also differences especially in registers offsets and sets of
supported functions.
This patch introduces the MAC SL submodule API which is intended to provide
a common way to access the MAC SL submodule and hide HW integrations
details.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
move common hw init code in separate function as preparation for adding new
switchdev driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_addr_t for desc_mem_phys and desc_hw_addr to avoid types
conversions.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to add a switchdev based cpsw driver move the common
header definitions to cpsw_priv.h. The plan is to develop a new driver on
switchdev driver model and obsolete the current cpsw driver after all
required functions are added to the new driver. This patch allows the same
header file to be re-used on both drivers during the transition period.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework probe to group common hw initialization:
- group resources request at the beginning of the probe
- move net device initialization and registration at the end of the probe
- drop cpsw_slave_init
as preparation of refactoring of common hw initialization code to
separate function.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Davinci MDIO in most of the case implemented as module inside of TI
CPSW subsystem and fully depends on CPSW to be enabled, but historically
it's implemented as separate Platform device/driver and defined in DT files
in two ways:
- as standalone node
- as child node of CPSW subsystem.
In later case it's required to split CPSW subsystem "reg" property to
exclude MDIO I/O range which is not useful.
Hence, replace devm_ioremap_resource() with devm_ioremap() to allow define
full I/O range in parent CPSW subsystem without spliting.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not delete multicast supervisory packet's (SUPER) entries while flushing
multicast addresses from ALE table cpsw_ale_flush_multicast(). Those
entries have to be added/removed only explicitly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now CPSW ALE will set/clean Host port bit in Unregistered Multicast Flood
Mask (UNREG_MCAST_FLOOD_MASK) for every VLAN without checking if this port
belongs to VLAN or not when ALLMULTI mode flag is set for nedev. This is
working in non dual_mac mode, but in dual_mac - it causes
enabling/disabling ALLMULTI flag for both ports.
Hence fix it by adding additional parameter to cpsw_ale_set_allmulti() to
specify ALE port number for which ALLMULTI has to be enabled and check if
port belongs to VLAN before modifying UNREG_MCAST_FLOOD_MASK.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ALE_PORT_HOST define for host port in cpsw_ale_set_allmulti() instead
of constants.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use correct define ALE_SUPER for ALE Multicast Address Table Entry
Supervisory Packet (SUPER) bit setting instead of ALE_BLOCKED. No issues
were observed till now as it have never been set, but it's going to be used
by new CPSW switch driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxime Chevallier