The v4l2_subdev core s_power op was used for two different things: power on/off
sensors or video decoders/encoders and to put a tuner in standby (and only the
tuner!). There is no 'tuner wakeup' op, that's done automatically when the tuner
is accessed.
The danger with calling (s_power, 0) to put a tuner into standby is that it is
usually broadcast for all subdevs. So a video receiver subdev that supports
s_power will also be powered off, and since there is no corresponding (s_power, 1)
they will never be powered on again.
In addition, this is specifically meant for tuners only since they draw the most
current.
This patch adds a new tuner op called 'standby' and replaces all calls to
(core, s_power, 0) by (tuner, standby). This prevents confusion between the two
uses of s_power. Note that there is no overlap: bridge drivers either just want
to put the tuner into standby, or they deal with powering on/off sensors. Never
both.
This also makes it easier to replace s_power for the remaining bridge drivers
with some PM code later.
Whether we want something cleaner for tuners in the future is a separate topic.
There is a lot of legacy code surrounding tuners, and I am very hesitant about
making changes there.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We must return -ENODEV error on case probe() fails to detect chip.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement V4L2 subdevice for bandwidth and frequency controls of
SDR usage. That driver now implements both DVB frontend and V4L2
subdevice. Driver itself is I2C driver. Lets see how it works.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Calculate low-pass filter control word dynamically from given radio
channel bandwidth.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace home made register access routines with regmap.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename driver state from priv to dev.
Remove legacy i2c-gate control.
Use I2C client for proper dev_() logging.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Calculate PLL dividers slightly differently, most likely it is now
correct. Move some register values to innitab. Use jiffies to poll
filter lock. Fix logging.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All users are using driver via I2C client binding so lets remove
unneeded media binding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There was some frequency calculation overflows which caused tuning
failure on 32-bit architecture. Use 64-bit numbers where needed in
order to avoid calculation overflows.
Thanks for the Finnish person, who asked remain anonymous, reporting,
testing and suggesting the fix.
Cc: <stable@vger.kernel.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/tuners/e4000.c:50:1: warning: 'e4000_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/e4000.c:83:1: warning: 'e4000_rd_regs' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/fc2580.c:66:1: warning: 'fc2580_wr_regs.constprop.1' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/fc2580.c:98:1: warning: 'fc2580_rd_regs.constprop.0' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/tda18212.c:57:1: warning: 'tda18212_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/tda18212.c:90:1: warning: 'tda18212_rd_regs.constprop.0' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/tda18218.c:60:1: warning: 'tda18218_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/tda18218.c:92:1: warning: 'tda18218_rd_regs.constprop.0' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It was a bad idea, as comment also says, to write some "don't care"
registers as 0xff value. Fix it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes the following warnings on a 32 bit system with GCC 4.4.3 and kernel Ubuntu 2.6.32-43 32 bit:
WARNING: "__udivdi3" [fc2580.ko] undefined!
WARNING: "__umoddi3" [fc2580.ko] undefined!
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fc2580.c: In function 'fc2580_set_params':
fc2580.c:118: warning: 'ret' may be used uninitialized in this function
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fc2580.c: In function 'fc2580_set_params':
fc2580.c:150: warning: this decimal constant is unsigned only in ISO C90
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Callbacks were set even attach failed. This leads calling
.release() in error case and resulted crash.
Reported-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is initial support for the Asus MyCinema U3100Mini Plus. The driver
in its current form gets detected and loads properly.
Scanning using dvbscan works without problems, Locking onto a channel
using tzap also works fine. Only playback using tzap -r + mplayer was
tested and was fully functional.
It uses the af9035 USB Bridge chip, with an af9033 demodulator. The tuner
used is the FCI FC2580.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil