When a link is going down the driver will be calling fnic_cleanup_io(),
which will traverse all commands and calling 'done' for each found command.
While the traversal is handled under the host_lock, calling 'done' happens
after the host_lock is being dropped.
As fnic_queuecommand_lck() is being called with the host_lock held, it
might well be that it will pick the command being selected for abortion
from the above routine and enqueue it for sending, but then 'done' is being
called on that very command from the above routine.
Which of course confuses the hell out of the scsi midlayer.
So fix this by not queueing commands when fnic_cleanup_io is active.
Link: https://lore.kernel.org/r/20200116102053.62755-1-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gcc -O3 warns that some local variables are not properly initialized:
drivers/scsi/fnic/vnic_dev.c: In function 'fnic_dev_hang_notify':
drivers/scsi/fnic/vnic_dev.c:511:16: error: 'a0' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[0] = *a0;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:691:6: note: 'a0' was declared here
u64 a0, a1;
^~
drivers/scsi/fnic/vnic_dev.c:512:16: error: 'a1' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[1] = *a1;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:691:10: note: 'a1' was declared here
u64 a0, a1;
^~
drivers/scsi/fnic/vnic_dev.c: In function 'fnic_dev_mac_addr':
drivers/scsi/fnic/vnic_dev.c:512:16: error: 'a1' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[1] = *a1;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:698:10: note: 'a1' was declared here
u64 a0, a1;
^~
Apparently the code relies on the local variables occupying adjacent memory
locations in the same order, but this is of course not guaranteed.
Use an array of two u64 variables where needed to make it work correctly.
I suspect there is also an endianness bug here, but have not digged in deep
enough to be sure.
Fixes: 5df6d737dd ("[SCSI] fnic: Add new Cisco PCI-Express FCoE HBA")
Fixes: mmtom ("init/Kconfig: enable -O3 for all arches")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200107201602.4096790-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The memory chunk io_req is released by mempool_free. Accessing
io_req->start_time will result in a use after free bug. The variable
start_time is a backup of the timestamp. So, use start_time here to
avoid use after free.
Link: https://lore.kernel.org/r/1572881182-37664-1-git-send-email-bianpan2016@163.com
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don't populate the array dev_cmd_err on the stack but instead make it
static const. Makes the object code smaller by 80 bytes.
Before:
text data bss dec hex filename
21461 1564 0 23025 59f1 drivers/scsi/fnic/vnic_dev.o
After:
text data bss dec hex filename
21318 1628 0 22946 59a2 drivers/scsi/fnic/vnic_dev.o
(gcc version 9.2.1, amd64)
Link: https://lore.kernel.org/r/20190906163945.3889-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
pci_alloc_irq_vectors() returns number of vectors allocated. Fix the check
for error condition.
Fixes: cca678dfba ("scsi: fnic: switch to pci_alloc_irq_vectors")
Link: https://lore.kernel.org/r/20190827211340.1095-1-gvaradar@cisco.com
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Acked-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Port speed printing was added by commit d948e6383e ("scsi: fnic: Add port
speed stat to fnic debug stats"). As currently configured, this will cause
the port speed to be printed to syslog every 2 seconds. To prevent log
spamming, only print the vnic port speed at driver initialization and if
the speed changes. Also clean up a small typo in fnic_trace.c.
Fixes: d948e6383e ("scsi: fnic: Add port speed stat to fnic debug stats")
Signed-off-by: John Pittman <jpittman@redhat.com>
Reviewed-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable ret is initialized to a value that is never read and it is
re-assigned later and immediately returns. Clean up the code by removing
rc and just returning 0.
[mkp: typo]
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/fnic/vnic_wq.c: In function 'vnic_wq_alloc_bufs':
drivers/scsi/fnic/vnic_wq.c:50:19: warning:
variable 'vdev' set but not used [-Wunused-but-set-variable]
drivers/scsi/fnic/vnic_rq.c: In function 'vnic_rq_alloc_bufs':
drivers/scsi/fnic/vnic_rq.c:30:19: warning:
variable 'vdev' set but not used [-Wunused-but-set-variable]
Never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling debugfs functions, there is no need to ever check the return
value. The function can work or not, but the code logic should never do
something different based on this.
Cc: Satish Kharat <satishkh@cisco.com>
Cc: Sesidhar Baddela <sebaddel@cisco.com>
Cc: Karan Tilak Kumar <kartilak@cisco.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update fnic driver to version 1.6.0.47.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds changes to check if fnic devcmd2 interface is exported by
the firmware. If devcmd2 interfaces is exported, driver starts using it
else falls back to fnic devcmd1 interface.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds fnic devcmd2 interfaces for initialization and posting
commands to fw.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds the devcmd2 wq initalization and devcmd2 ring allocation
helper interfaces used by devcmd2 init.
[mkp: typos]
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds the fnic devcmd2 controller definitions.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds the fnic devcmd2 command structre and the command result
structure definitions.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Impose an upper limit on the max number of CQ entries (corresponding to the
copy wq) processed in an interrupt. Use module parameter to set the limit.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do RQ enable before posting descriptor. This is needed for later hw
revisions.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Doing vnic_device_enable before this could cause interrupts to happen
before they are setup.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The change is to print warning when scsi done is called for an IO that has
not yet been issued to the fw. Also adding sc and tag to debug print when
IO is cleaned up.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change is to add fnic stats for the max number of CQs (corresponding
to copy WQ) processed in a given interrupt, max time taken by the ISR.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds the current fnic port speed stat to fnic debug stats.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Need to use fnic_lock as well as host lock in that order to set state
flags.
[mkp: typos]
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
rq->ctrl not enabled when this is called is bad but not fatal and can
continue.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch changes the default lun queuedepth for fnic to 256.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is to add fnic 20G port speed display in sysfs.
[mkp: typo]
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas. Additionally, we have
a pile of annotation, unused variable and minor updates. The big API
change is the updates for Christoph's DMA rework which include
removing the DISABLE_CLUSTERING flag. And finally there are a couple
of target tree updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXCEUNiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdjKAP9vrTTv
qFaYmAoRSbPq9ZiixaXLMy0K/6o76Uay0gnBqgD/fgn3jg/KQ6alNaCjmfeV3wAj
u1j3H7tha9j1it+4pUw=
=GDa+
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas.
Additionally, we have a pile of annotation, unused variable and minor
updates.
The big API change is the updates for Christoph's DMA rework which
include removing the DISABLE_CLUSTERING flag.
And finally there are a couple of target tree updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (259 commits)
scsi: isci: request: mark expected switch fall-through
scsi: isci: remote_node_context: mark expected switch fall-throughs
scsi: isci: remote_device: Mark expected switch fall-throughs
scsi: isci: phy: Mark expected switch fall-through
scsi: iscsi: Capture iscsi debug messages using tracepoints
scsi: myrb: Mark expected switch fall-throughs
scsi: megaraid: fix out-of-bound array accesses
scsi: mpt3sas: mpt3sas_scsih: Mark expected switch fall-through
scsi: fcoe: remove set but not used variable 'port'
scsi: smartpqi: call pqi_free_interrupts() in pqi_shutdown()
scsi: smartpqi: fix build warnings
scsi: smartpqi: update driver version
scsi: smartpqi: add ofa support
scsi: smartpqi: increase fw status register read timeout
scsi: smartpqi: bump driver version
scsi: smartpqi: add smp_utils support
scsi: smartpqi: correct lun reset issues
scsi: smartpqi: correct volume status
scsi: smartpqi: do not offline disks for transient did no connect conditions
scsi: smartpqi: allow for larger raid maps
...
Most SCSI drivers want to enable "clustering", that is merging of
segments so that they might span more than a single page. Remove the
ENABLE_CLUSTERING define, and require drivers to explicitly set
DISABLE_CLUSTERING to disable this feature.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The way these functions abuse ->special to try to store the dummy
request looks completely broken, given that it actually stores the
original scsi command.
Instead switch to ->host_scribble and store the actual dummy command.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Would be nice to fix up the SCSI midlayer instead, but this will do for
now.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Satish Kharat <satishkh@cisco.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in fnic stats message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
struct timespec is deprecated since it overflows in 2038 on 32-bit
architectures, so we should use timespec64 consistently.
I'm slightly adapting the format strings here, to make sure we print the
nanoseconds with the correct number of leading zeroes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This saves a little .text and gets rid of the unmotivated line break and
the sizeof(...) style inconsistency.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fnic_fcpio_icmnd_cmpl_handler() displays the value of sc with:
FNIC_SCSI_DBG(KERN_INFO...
"... sc = 0x%p"
"scsi_status ..."
...
As the literal strings get merged, the function uses %ps instead of the
intended raw %p format. Fix this by inserting a space.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the duplicate copies of this simple function and use an
open-coded version.
drivers/scsi/fnic/fnic_debugfs.c:122:11-31: WARNING opportunity for simple_open, see also structure on line 223
Generated by: coccinelle/api/simple_open.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Command abort already returns FAILED, which will then be escalated to a
host reset. So no need to call host_reset directly.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The MSI interrupt name can require 11 bytes in addition to the device name,
for a total of 23 bytes:
drivers/scsi/fnic/fnic_isr.c: In function 'fnic_request_intr':
drivers/scsi/fnic/fnic_isr.c:192:4: error: '-fcs-rq' directive writing 7 bytes into a region of size between 5 and 16 [-Werror=format-overflow=]
"%.11s-fcs-rq", fnic->name);
drivers/scsi/fnic/fnic_isr.c:206:3: note: 'sprintf' output between 12 and 23 bytes into a destination of size 16
sprintf(fnic->msix[FNIC_MSIX_ERR_NOTIFY].devname,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%.11s-err-notify", fnic->name);
This extends the buffer to fit any possible value.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual suspects: lpfc, qla2xxx, bnx2fc,
qedf, hpsa, hisi_sas, smartpqi, cxlflash, aacraid, csiostor along with
a host of minor and miscellaneous changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=D9QX
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, bnx2fc,
qedf, hpsa, hisi_sas, smartpqi, cxlflash, aacraid, csiostor along with
a host of minor and miscellaneous changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (276 commits)
qla2xxx: Fix NVMe entry_type for iocb packet on BE system
scsi: qla2xxx: avoid unused-function warning
scsi: snic: fix a couple of spelling mistakes/typos
scsi: qla2xxx: fix a bunch of typos and spelling mistakes
scsi: lpfc: don't double count abort errors
scsi: lpfc: spin_lock_irq() is not nestable
scsi: hisi_sas: optimise DMA slot memory
scsi: ibmvfc: constify dev_pm_ops structures.
scsi: ibmvscsi: constify dev_pm_ops structures.
scsi: cxlflash: Update debug prints in reset handlers
scsi: cxlflash: Update send_tmf() parameters
scsi: cxlflash: Avoid double free of character device
scsi: Add STARGET_CREATED_REMOVE state to scsi_target_state
scsi: ses: do not add a device to an enclosure if enclosure_add_links() fails.
scsi: ufs: flush eh_work when eh_work scheduled.
scsi: qla2xxx: Protect access to qpair members with qpair->qp_lock
scsi: sun_esp: fix device reference leaks
scsi: fnic: changing queue command to return result DID_IMM_RETRY when rport is init
scsi: fnic: correct speed display and add support for 25,40 and 100G
scsi: fnic: added timestamp reporting in fnic debug stats
...
Currently the queue command returns DID_NO_CONNECT anytime the rport is
not in RPORT_ST_READY state. Changing it to return DID_NO_CONNECT only
when the rport is in RPORT_ST_DELETE state. When the rport is in one of
the init states retruning DID_IMM_RETRY.
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Setting speed based on the vinc device parameter read during
linkup. Also adding support to display 25,40 and 100G
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added the timestamps for
1. current timestamp
2. last fnic stats read timestamp
3. last fnic stats reset timestamp
and the deltas since last stats read and last reset in fnic stats.
fnic stats uses debugfs
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
io_cmpl_skip keep track of number of completions to skip when stats are
reset. If a fw_reset happens immediately after stats reset it could put
it out of sync so need to reset io_cmpl_skip when fw reset is completed.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = {
skb_pull,
__skb_pull,
skb_pull_inline,
__pskb_pull_tail,
__pskb_pull,
pskb_pull
};
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = {
skb_pull,
__skb_pull,
skb_pull_inline,
__pskb_pull_tail,
__pskb_pull,
pskb_pull
};
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a bug introduced when they moved the fip subcodes to central
place. Was sending FIP_SC_VL_NOTE in fip.fip_subcode for VLAN request in
fnic_fcoe_send_vlan_req. Change is to use FIP_SC_VL_REQ instead.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The IO and Abort latency counter counts the time taken to complete the
IO and abort command into broad buckets. This is not intended for
performance measurement, just a debug statistic. current_max_io_time
tries to keep track of the maximum time an IO has taken to complete if
it is > 30sec.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke