Bring the kernel-doc headers in sync with the function argument lists.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A left shift must shift less than the bit width of the left argument.
Avoid triggering undefined behavior if ha->mbx_count == 32.
This patch avoids that UBSAN reports the following complaint:
UBSAN: Undefined behaviour in drivers/scsi/qla2xxx/qla_isr.c:275:14
shift exponent 32 is too large for 32-bit type 'int'
Call Trace:
dump_stack+0x4e/0x6c
ubsan_epilogue+0xd/0x3b
__ubsan_handle_shift_out_of_bounds+0x112/0x14c
qla2x00_mbx_completion+0x1c5/0x25d [qla2xxx]
qla2300_intr_handler+0x1ea/0x3bb [qla2xxx]
qla2x00_mailbox_command+0x77b/0x139a [qla2xxx]
qla2x00_mbx_reg_test+0x83/0x114 [qla2xxx]
qla2x00_chip_diag+0x354/0x45f [qla2xxx]
qla2x00_initialize_adapter+0x2c2/0xa4e [qla2xxx]
qla2x00_probe_one+0x1681/0x392e [qla2xxx]
pci_device_probe+0x10b/0x1f1
driver_probe_device+0x21f/0x3a4
__driver_attach+0xa9/0xe1
bus_for_each_dev+0x6e/0xb5
driver_attach+0x22/0x3c
bus_add_driver+0x1d1/0x2ae
driver_register+0x78/0x130
__pci_register_driver+0x75/0xa8
qla2x00_module_init+0x21b/0x267 [qla2xxx]
do_one_initcall+0x5a/0x1e2
do_init_module+0x9d/0x285
load_module+0x20db/0x38e3
SYSC_finit_module+0xa8/0xbc
SyS_finit_module+0x9/0xb
do_syscall_64+0x77/0x271
entry_SYSCALL64_slow_path+0x25/0x25
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
for session deletion, replace sess_lock with work_lock.
Under certain case sess_lock is not feasiable to acquire.
The lock is needed temporarily to make sure a single
call to schedule of the work element.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch scan is assumed to succeed most of the time.
If the scan failed, then scan is limit 5 retries.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When connection type is N_Port to N_Port (point-to-point), there
is a possibilty where initiator will not send PLOGI request and
will directly send PRLI. In N2N connection the port has higher
port name sends the PLOGI but not allow to send PRLI if is a
target mode. Only initiator is allowed to send PRLI.
Current driver code deletes old session when it receives PLOGI
request. If we will not receive PLOGI request then we will not
delete old session and create new session. Add check for N2N
with PRLI receive only and trigger cleanup. For this case, the
cleanup requires individual cmd abort instead of using implicit
logout as a broad stroke flush.
Signed-off-by: Krishna Kant <krishna.kant@purestorage.com>
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use IOCB patch to submit Control VP MBX command to reduce
bottle-neck for mbx interface.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid that building with gcc 7 and W=1 triggers warnings similar to the
following:
drivers/scsi/qla2xxx/qla_isr.c:1189:27: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: Quinn Tran <quinn.tran@cavium.com>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
GPNID is triggered by RSCN. For multiple RSCNs of the same affected
NPORT ID, serialize the GPNID to prevent confusion.
Fixes: 726b854870 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When NPort Handle is in use, driver needs to mark the handle as used and
pick another. Instead, the code clears the handle and re-pick the same
handle.
Fixes: 726b854870 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Always use bsg_job->reply instead of scsi_req(bsg_job->req)->sense), as
they always point to the same memory.
Never set scsi_req(bsg_job->req)->result and we'll set that value
through bsg_job_done.
[mkp: applied by hand, fixed whitespace]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Tested-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In some environments, user can choose to not enable SCSI-MQ but wants to
use FC-NVMe feature of the driver. Since driver relies on Q-Pairs to
allocate FC-NVMe resources, use existing module parameter to create
Q-Pairs when FC-NVMe is enabled.
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we discovered a topology that is N2N then we will issue a login to
the target. If our WWPN is bigger than the target's WWPN then we will
initiate login, otherwise we will just wait for the target to initiate
login.
[mkp: many whitespace errors]
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since commit 7401bc18d1 ("scsi: qla2xxx: Add FC-NVMe command
handling") we make use of 'struct nvmefc_fcp_req' in
qla24xx_nvme_iocb_entry() without including linux/nvme-fc-driver.h where
it is defined.
Add linux/nvme-fc-driver.h (and scsi/fc/fc_fs.h as nvme-fc-driver.h
needs the definition of 'struct fc_ba_rjt' from scsi/fc/fc_fs.h) to the
header files included by qla_isr.c.
Fixes: 7401bc18d1 ("scsi: qla2xxx: Add FC-NVMe command handling")
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SFP can come in 2 formats: short range/SR and long range/LR. For LR,
user the can increase the number of Buffer to Buffer credits between end
points via Cavium's command line tool. By default, FW uses a lower BB
Credit value optimized for SR. This patch will read the SFP for each
link up event and during chip reset sequence. If the SFP type and
setting are mismatch, then the chip is reset 1 time to use the
appropriate setting.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove extra register read for each interrupt for performance
improvement.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Following error will be logged in to message file while trying to
configure target with multiqueue.
"Cmd 0x1f aborted with timeout since ISP Abort is pending"
"qla25xx_init_queues Rsp que: 1 init failed."
Fixes: 82de802ad4 ("scsi: qla2xxx: Preparation for Target MQ.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to variable name, sfp_additonal_info should be
sfp_additional_info (add in missing i).
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support to the driver to set the exchange threshold value for
the number of outstanding AENs.
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull more block updates from Jens Axboe:
"This is a followup for block changes, that didn't make the initial
pull request. It's a bit of a mixed bag, this contains:
- A followup pull request from Sagi for NVMe. Outside of fixups for
NVMe, it also includes a series for ensuring that we properly
quiesce hardware queues when browsing live tags.
- Set of integrity fixes from Dmitry (mostly), fixing various issues
for folks using DIF/DIX.
- Fix for a bug introduced in cciss, with the req init changes. From
Christoph.
- Fix for a bug in BFQ, from Paolo.
- Two followup fixes for lightnvm/pblk from Javier.
- Depth fix from Ming for blk-mq-sched.
- Also from Ming, performance fix for mtip32xx that was introduced
with the dynamic initialization of commands"
* 'for-linus' of git://git.kernel.dk/linux-block: (44 commits)
block: call bio_uninit in bio_endio
nvmet: avoid unneeded assignment of submit_bio return value
nvme-pci: add module parameter for io queue depth
nvme-pci: compile warnings in nvme_alloc_host_mem()
nvmet_fc: Accept variable pad lengths on Create Association LS
nvme_fc/nvmet_fc: revise Create Association descriptor length
lightnvm: pblk: remove unnecessary checks
lightnvm: pblk: control I/O flow also on tear down
cciss: initialize struct scsi_req
null_blk: fix error flow for shared tags during module_init
block: Fix __blkdev_issue_zeroout loop
nvme-rdma: unconditionally recycle the request mr
nvme: split nvme_uninit_ctrl into stop and uninit
virtio_blk: quiesce/unquiesce live IO when entering PM states
mtip32xx: quiesce request queues to make sure no submissions are inflight
nbd: quiesce request queues to make sure no submissions are inflight
nvme: kick requeue list when requeueing a request instead of when starting the queues
nvme-pci: quiesce/unquiesce admin_q instead of start/stop its hw queues
nvme-loop: quiesce/unquiesce admin_q instead of start/stop its hw queues
nvme-fc: quiesce/unquiesce admin_q instead of start/stop its hw queues
...
Fix the following typos/spelling mistakes:
"attribure" -> "attribute"
"suppored" -> "supported"
"Symobilic" -> "Symbolic"
"iteself" -> "itself"
"reqeust" -> "request"
"nvme_wait_on_comand" -> "nvme_wait_on_command"
"bount" -> "bound"
"captrue_mask" -> "capture_mask"
"tempelate" -> "template"
..and also unwrap a line to fix a checkpatch warning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This code provides the interfaces to register remote and local ports of
FC4 type 0x28 with the FC-NVMe transport and transports the requests
(FC-NVMe FC link services and FC-NVMe commands IUs) to the fabric. It
also provides the support for allocating h/w queues and aborting FC-NVMe
FC requests.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds logic to handle the completion of FC-NVMe commands and
creates a sub-command in the SRB command structure to manage NVMe
commands.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add fw_started flag to qpair to reduce cache thrash. This reduce access
to qla_hw_data structure by each qpair.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For Target mode, user can control the work load by placing qla2xxx's irq
vector on certain CPU via the smp_affinity knob. This patch allows user
to control the number of QPair's irq to be active. The irqs are
allocated at driver load time until unload. The work itself is placed on
the QPair based on user setting.
Usage:
modprobe qla2xxx qlini_mode=disabled ql2xuctrlirq=1
mount -t debugfs none /sys/kernel/debug
echo 2 > /sys/kernel/debug/qla2xxx/qla2xxx_[host num]/naqp
echo [cpu id] > /proc/irq/[irq id]/smp_affinity_list
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable Multi Queue for Target mode. At Initiator LUN scan time, each LUN
is assign to a QPair. Each QPair is affinitize to certain CPU. When new
cmd arrives from the wire, the lunid is used to search for qpair. The
qpair's affinitized cpuid will be used to queue up the work element.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In Current code, Req Q 0, RespQ 0 & hardware_lock are the main resources
for sending and process completion of Target IO. These resources are now
referenced behind a new qpair/"struct qla_qpair base_qpair". Main path
IO handle will access those resources via the qpair pointer in
preparation for Target MQ.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Merge active/outstanding cmd arrays from target side and initiator side
together in prepration for Target Multi Queue support.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Assign unique id to all traces and logs for debug purpose.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Name server login is normally handle by FW. In some rare case where one
of the switches is being updated, name server login could get
affected. Trigger relogin to name server when driver detects this
condition.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Milan P Gandhi <mgandhi@redhat.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current driver wait for FW to be in the ready state before
processing in-coming commands. For Arbitrated Loop or
Point-to- Point (not switch), FW Ready state can take a while.
FW will transition to ready state after all Nports have been
logged in. In the mean time, certain initiators have completed
the login and starts IO. Driver needs to start processing all
queues if FW is already started.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The Mailbox interface is currently over subscribed. We like
to reserve the Mailbox interface for the chip managment and
link initialization. Any non essential Mailbox command will
be routed through the IOCB interface. The IOCB interface is
able to absorb more commands.
Following commands are being routed through IOCB interface
- Get ID List (007Ch)
- Get Port DB (0064h)
- Get Link Priv Stats (006Dh)
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If the remote port have started the login process, then the
PLOGI and PRLI should be back to back. Driver will allow
the remote port to complete the process. For the case where
the remote port decide to back off from sending PRLI, this
local port sets an expiration timer for the PRLI. Once the
expiration time passes, the relogin retry logic is allowed
to go through and perform login with the remote port.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is the set of stuff that didn't quite make the initial pull and a
set of fixes for stuff which did. The new stuff is basically lpfc
(nvme), qedi and aacraid. The fixes cover a lot of previously
submitted stuff, the most important of which probably covers some of
the failing irq vectors allocation and other fallout from having the
SCSI command allocated as part of the block allocation functions.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=e+6v
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the set of stuff that didn't quite make the initial pull and a
set of fixes for stuff which did.
The new stuff is basically lpfc (nvme), qedi and aacraid. The fixes
cover a lot of previously submitted stuff, the most important of which
probably covers some of the failing irq vectors allocation and other
fallout from having the SCSI command allocated as part of the block
allocation functions"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (59 commits)
scsi: qedi: Fix memory leak in tmf response processing.
scsi: aacraid: remove redundant zero check on ret
scsi: lpfc: use proper format string for dma_addr_t
scsi: lpfc: use div_u64 for 64-bit division
scsi: mac_scsi: Fix MAC_SCSI=m option when SCSI=m
scsi: cciss: correct check map error.
scsi: qla2xxx: fix spelling mistake: "seperator" -> "separator"
scsi: aacraid: Fixed expander hotplug for SMART family
scsi: mpt3sas: switch to pci_alloc_irq_vectors
scsi: qedf: fixup compilation warning about atomic_t usage
scsi: remove scsi_execute_req_flags
scsi: merge __scsi_execute into scsi_execute
scsi: simplify scsi_execute_req_flags
scsi: make the sense header argument to scsi_test_unit_ready mandatory
scsi: sd: improve TUR handling in sd_check_events
scsi: always zero sshdr in scsi_normalize_sense
scsi: scsi_dh_emc: return success in clariion_std_inquiry()
scsi: fix memory leak of sdpk on when gd fails to allocate
scsi: sd: make sd_devt_release() static
scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.
...
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- enable dual mode (initiator + target) qla2xxx operation. (Quinn +
Himanshu)
- add a framework for qla2xxx async fabric discovery. (Quinn +
Himanshu)
- enable iscsi PDU DDP completion offload in cxgbit/T6 NICs. (Varun)
- fix target-core handling of aborted failed commands. (Bart)
- fix a long standing target-core issue NULL pointer dereference with
active I/O LUN shutdown. (Rob Millner + Bryant + nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (44 commits)
target: Add counters for ABORT_TASK success + failure
iscsi-target: Fix early login failure statistics misses
target: Fix NULL dereference during LUN lookup + active I/O shutdown
target: Delete tmr from list before processing
target: Fix handling of aborted failed commands
uapi: fix linux/target_core_user.h userspace compilation errors
target: export protocol identifier
qla2xxx: Fix a warning reported by the "smatch" static checker
target/iscsi: Fix unsolicited data seq_end_offset calculation
target/cxgbit: add T6 iSCSI DDP completion feature
target/cxgbit: Enable DDP for T6 only if data sequence and pdu are in order
target/cxgbit: Use T6 specific macros to get ETH/IP hdr len
target/cxgbit: use cxgb4_tp_smt_idx() to get smt idx
target/iscsi: split iscsit_check_dataout_hdr()
target: Remove command flag CMD_T_DEV_ACTIVE
target: Remove command flag CMD_T_BUSY
target: Move session check from target_put_sess_cmd() into target_release_cmd_kref()
target: Inline transport_cmd_check_stop()
target: Remove an overly chatty debug message
target: Stop execution if CMD_T_STOP has been set
...
For target mode, we need to increase minimum vectors value by one to
account for ATIO queue.
Following stack trace will be seen
Call Trace:
qla24xx_config_rings+0x15a/0x230 [qla2xxx]
qla2x00_init_rings+0x1a1/0x3a0 [qla2xxx]
qla2x00_restart_isp+0x5c/0x120 [qla2xxx]
qla2x00_abort_isp+0x138/0x430 [qla2xxx]
? __schedule+0x260/0x580
qla2x00_do_dpc+0x3bc/0x920 [qla2xxx]
? qla2x00_relogin+0x290/0x290 [qla2xxx]
? schedule+0x3a/0xa0
? qla2x00_relogin+0x290/0x290 [qla2xxx]
kthread+0x103/0x140
? __kthread_init_worker+0x40/0x40
ret_from_fork+0x29/0x40
RIP: qlt_24xx_config_rings+0x6c/0x90
[mkp: fixed Fixes: hash]
Cc: <stable@vger.kernel.org>
Fixes: 17e5fc5858 ("scsi: qla2xxx: fix MSI-X vector affinity")
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This update includes the usual round of major driver updates (ncr5380,
ufs, lpfc, be2iscsi, hisi_sas, storvsc, cxlflash, aacraid,
megaraid_sas, ). There's also an assortment of minor fixes and the
major update of switching a bunch of drivers to pci_alloc_irq_vectors
from Christoph.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=cBQx
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
ufs, lpfc, be2iscsi, hisi_sas, storvsc, cxlflash, aacraid,
megaraid_sas, ...).
There's also an assortment of minor fixes and the major update of
switching a bunch of drivers to pci_alloc_irq_vectors from Christoph"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (188 commits)
scsi: megaraid_sas: handle dma_addr_t right on 32-bit
scsi: megaraid_sas: array overflow in megasas_dump_frame()
scsi: snic: switch to pci_irq_alloc_vectors
scsi: megaraid_sas: driver version upgrade
scsi: megaraid_sas: Change RAID_1_10_RMW_CMDS to RAID_1_PEER_CMDS and set value to 2
scsi: megaraid_sas: Indentation and smatch warning fixes
scsi: megaraid_sas: Cleanup VD_EXT_DEBUG and SPAN_DEBUG related debug prints
scsi: megaraid_sas: Increase internal command pool
scsi: megaraid_sas: Use synchronize_irq to wait for IRQs to complete
scsi: megaraid_sas: Bail out the driver load if ld_list_query fails
scsi: megaraid_sas: Change build_mpt_mfi_pass_thru to return void
scsi: megaraid_sas: During OCR, if get_ctrl_info fails do not continue with OCR
scsi: megaraid_sas: Do not set fp_possible if TM capable for non-RW syspdIO, change fp_possible to bool
scsi: megaraid_sas: Remove unused pd_index from megasas_build_ld_nonrw_fusion
scsi: megaraid_sas: megasas_return_cmd does not memset IO frame to zero
scsi: megaraid_sas: max_fw_cmds are decremented twice, remove duplicate
scsi: megaraid_sas: update can_queue only if the new value is less
scsi: megaraid_sas: Change max_cmd from u32 to u16 in all functions
scsi: megaraid_sas: set pd_after_lb from MR_BuildRaidContext and initialize pDevHandle to MR_DEVHANDLE_INVALID
scsi: megaraid_sas: latest controller OCR capability from FW before sending shutdown DCMD
...
Six fairly small fixes. None is a real show stopper, two automation
detected problems: one memory leak, one use after free and four others
each of which fixes something that has been a significant source of
annoyance to someone.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=5Fct
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fairly small fixes. None is a real show stopper, two automation
detected problems: one memory leak, one use after free and four others
each of which fixes something that has been a significant source of
annoyance to someone"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: zfcp: fix use-after-free by not tracing WKA port open/close on failed send
scsi: aacraid: Fix INTx/MSI-x issue with older controllers
scsi: mpt3sas: disable ASPM for MPI2 controllers
scsi: mpt3sas: Force request partial completion alignment
scsi: qla2xxx: Avoid that issuing a LIP triggers a kernel crash
scsi: qla2xxx: Fix a recently introduced memory leak
This patch simplifies SRB structure usage in driver.
- Simplify sp->done() and sp->free() interfaces.
- Remove sp->fcport->vha to use vha pointer from sp.
- Use sp->vha context in qla2x00_rel_sp().
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Current code blindly does State Change Registration when
the link is up. Move SCR behind fabric scan, so that arbitrated
loop scan would not get erroneous error message.
Some of the other improvements are as follows
- Add session deletion for TPRLO and send acknowledgment for TPRLO.
- Enable FW option to move ABTS, RIDA & PUREX from RSPQ to ATIOQ.
- Save NPort ID early in link init.
- Move ABTS & RIDA to ATIOQ helps in keeping command ordering and
link up sequence ordering.
- Save Nport ID and update VP map so that SCSI CMD/ATIO won't be dropped.
- fcport alloc does the initializes memory to zero. Remove memset to
zero since It might corrupt link list.
- Turn off Registration for State Change MB in loop mode.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add switch to allow both Initiator Mode & Target
mode to operate at the same time.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Currently code performs a full scan of the fabric for
every RSCN. Its an expensive process in a noisy large SAN.
This patch optimizes expensive fabric discovery process by
scanning switch for the affected port when RSCN is received.
Currently Initiator Mode code makes login/logout decision without
knowledge of target mode. This causes driver and firmware to go
out-of-sync. This framework synchronizes both initiator mode
personality and target mode personality in making login/logout
decision.
This patch adds following capabilities in the driver
- Send Notification Acknowledgement asynchronously.
- Update session/fcport state asynchronously.
- Create a session or fcport struct asynchronously.
- Send GNL asynchronously. The command will ask FW to
provide a list of FC Port entries FW knows about.
- Send GPDB asynchronously. The command will ask FW to
provide detail data of an FC Port FW knows about or
perform ADISC to verify the state of the session.
- Send GPNID asynchronously. The command will ask switch
to provide WWPN for provided NPort ID.
- Send GPSC asynchronously. The command will ask switch
to provide registered port speed for provided WWPN.
- Send GIDPN asynchronously. The command will ask the
switch to provide Nport ID for provided WWPN.
- In driver unload path, schedule all session for deletion
and wait for deletion to complete before allowing driver
unload to proceed.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
[ bvanassche: fixed spelling in patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Callback for sp->done expects scsi_qla_host is passed in as argument,
Instead qla_hw_data is passed in.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
And require all drivers that want to support BLOCK_PC to allocate it
as the first thing of their private data. To support this the legacy
IDE and BSG code is switched to set cmd_size on their queues to let
the block layer allocate the additional space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
qla2x00_probe_one() allocates IRQs before it initializes rsp_q_map so
IRQs must be freed even if rsp_q_map allocation did not occur. This was
detected by kmemleak.
Fixes: 4fa1834559 ("scsi: qla2xxx: Utilize pci_alloc_irq_vectors/pci_free_irq_vectors calls")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Michael Hernandez <michael.hernandez@cavium.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-By: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull SCSI target fixes from Bart Van Assche:
- two small fixes for the ibmvscsis driver
- ten patches with bug fixes for the target mode of the qla2xxx driver
- four patches that avoid that the "sparse" and "smatch" static
analyzer tools report false positives for the qla2xxx code base
* 'scsi-target-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bvanassche/linux:
qla2xxx: Disable out-of-order processing by default in firmware
qla2xxx: Fix erroneous invalid handle message
qla2xxx: Reduce exess wait during chip reset
qla2xxx: Terminate exchange if corrupted
qla2xxx: Fix crash due to null pointer access
qla2xxx: Collect additional information to debug fw dump
qla2xxx: Reset reserved field in firmware options to 0
qla2xxx: Set tcm_qla2xxx version to automatically track qla2xxx version
qla2xxx: Include ATIO queue in firmware dump when in target mode
qla2xxx: Fix wrong IOCB type assumption
qla2xxx: Avoid that building with W=1 triggers complaints about set-but-not-used variables
qla2xxx: Move two arrays from header files to .c files
qla2xxx: Declare an array with file scope static
qla2xxx: Fix indentation
ibmvscsis: Fix sleeping in interrupt context
ibmvscsis: Fix max transfer length
Termination of Immediate Notify IOCB was using wrong
IOCB handle. IOCB completion code was unable to find
appropriate code path due to wrong handle.
Following message is seen in the logs.
"Error entry - invalid handle/queue (ffff)."
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: Fixed word order in patch title ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Now that qla2xxx uses the IRQ layer affinity assignment, affinity won't
change over the life time of a device and the notifiers are useless.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The first two or three vectors in qla2xxx adapter are global and not
associated with a specific queue. They should not have IRQ affinity
assigned.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
msix_entries and qla82xx_msix_entries arrays are never modified in
drivers/scsi/qla2xxx/qla_isr.c. Move their contents to read-only data.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla24xx_enable_msix() calls scnprintf() with a non-literal format
string. This makes clang report -Wformat-security warnings when
compiling this function:
drivers/scsi/qla2xxx/qla_isr.c:3083:7: error: format string is not a
string literal (potentially insecure) [-Werror,-Wformat-security]
msix_entries[i].name);
^~~~~~~~~~~~~~~~~~~~
drivers/scsi/qla2xxx/qla_isr.c:3083:7: note: treat the string as an
argument to avoid this
msix_entries[i].name);
^
"%s",
drivers/scsi/qla2xxx/qla_isr.c:3119:7: error: format string is not a
string literal (potentially insecure) [-Werror,-Wformat-security]
msix_entries[QLA_ATIO_VECTOR].name);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qla2xxx/qla_isr.c:3119:7: note: treat the string as an
argument to avoid this
msix_entries[QLA_ATIO_VECTOR].name);
^
"%s",
Even though msix_entries[...].name are initialized as literal strings
with no % character and are never modified, introduce a "%s" format
parameter in order to silence this -Wformat-security warning and make
clang able to detect at compile time real bugs related to string
formatting.
[mkp: typo]
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly stuff which missed the initial pull. There's a new
driver: qedi, some ufs, ibmvscsis and ncr5380 updates plus some
assorted driver fixes and also a fix for the bug where if a device
goes into a blocked state between configuration and sysfs device add
(which can be a long time under async probing) it would become
permanently blocked.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Zofc
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull late SCSI updates from James Bottomley:
"This is mostly stuff which missed the initial pull.
There's a new driver: qedi, and some ufs, ibmvscsis and ncr5380
updates plus some assorted driver fixes and also a fix for the bug
where if a device goes into a blocked state between configuration and
sysfs device add (which can be a long time under async probing) it
would become permanently blocked"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (30 commits)
scsi: avoid a permanent stop of the scsi device's request queue
scsi: mpt3sas: Recognize and act on iopriority info
scsi: qla2xxx: Fix Target mode handling with Multiqueue changes.
scsi: qla2xxx: Add Block Multi Queue functionality.
scsi: qla2xxx: Add multiple queue pair functionality.
scsi: qla2xxx: Utilize pci_alloc_irq_vectors/pci_free_irq_vectors calls.
scsi: qla2xxx: Only allow operational MBX to proceed during RESET.
scsi: hpsa: remove memory allocate failure message
scsi: Update 3ware driver email addresses
scsi: zfcp: fix rport unblock race with LUN recovery
scsi: zfcp: do not trace pure benign residual HBA responses at default level
scsi: zfcp: fix use-after-"free" in FC ingress path after TMF
scsi: libcxgbi: return error if interface is not up
scsi: cxgb4i: libcxgbi: add missing module_put()
scsi: cxgb4i: libcxgbi: cxgb4: add T6 iSCSI completion feature
scsi: cxgb4i: libcxgbi: add active open cmd for T6 adapters
scsi: cxgb4i: use cxgb4_tp_smt_idx() to get smt_idx
scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.
scsi: aacraid: remove wildcard for series 9 controllers
scsi: ibmvscsi: add write memory barrier to CRQ processing
...
Pull scsi target cleanups from Bart Van Assche:
"The changes here are:
- a few small bug fixes for the iSCSI and user space target drivers.
- minimize the target build time by about 30% by rearranging #include
directives
- fix the second argument passed to percpu_ida_alloc()
- reduce the number of false positive warnings reported by sparse
These patches pass Wu Fengguang's build bot tests and also the
linux-next tests"
* 'scsi-target-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bvanassche/linux:
iscsi-target: Return error if unable to add network portal
target: Fix spelling mistake and unwrap multi-line text
target/iscsi: Fix double free in lio_target_tiqn_addtpg()
target/user: Fix use-after-free of tcmu_cmds if they are expired
target: Minimize #include directives
target/user: Add an #include directive
cxgbit: Add an #include directive
ibmvscsi_tgt: Add two #include directives
sbp-target: Add an #include directive
qla2xxx: Add an #include directive
configfs: Minimize #include directives
usb: gadget: Fix second argument of percpu_ida_alloc()
sbp-target: Fix second argument of percpu_ida_alloc()
target/user: Fix a data type in tcmu_queue_cmd()
target: Use NULL instead of 0 to represent a pointer
- Fix race condition between dpc_thread accessing Multiqueue resources
and qla2x00_remove_one thread trying to free resource.
- Fix out of order free for Multiqueue resources. Also, Multiqueue
interrupts needs a workqueue. Interrupt needed to stop before
the wq can be destroyed.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replaced existing multiple queue functionality with framework
that allows for the creation of pairs of request and response queues,
either at start of day or dynamically.
Queue pair creation depend on module parameter "ql2xmqsupport",
which need to be enabled to create queue pair.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replaces the old pci_enable_msi[x]* and pci_disable_msi[x] calls.
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following statement in qla_isr.c needs the size of struct
t10_pi_tuple:
spt += j;
Hence include the <linux/t10-pi.h> header file.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Change FC drivers to use 'struct bsg_job' from bsg-lib.h instead of
'struct fc_bsg_job' from scsi_transport_fc.h and remove 'struct
fc_bsg_job'.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don't use fc_bsg_job::request and fc_bsg_job::reply directly, but use
helper variables bsg_request and bsg_reply. This will be helpful when
transitioning to bsg-lib.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of defining a local version of it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla2xxx first calls request_irq() and then does the setup of the queue
entry data needed in the interrupt handlers in when using MSI-X. This
could lead to a NULL pointer dereference when an IRQ fires between the
request_irq() call and the assignment of the qentry data structure to
the rsp->msix field. A possible case for such a race would be in the
kdump case when the HBA's IRQs are still enabled but the driver is
undergoing a new initialisation and thus is not aware of already
activated IRQs in the HBA.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ Upstream Commit 84e32a06f4 ]
Commit 84e32a0 ("qla2xxx: Use pci_enable_msix_range() instead of
pci_enable_msix()") introduced a regression when target mode is enabled.
In qla24xx_enable_msix(), ha->max_rsp_queues was incorrectly set
to a value higher than the number of response queues allocated causing
an invalid dereference. Specifically here in qla2x00_init_rings():
*rsp->in_ptr = 0;
Add additional check to make sure the pointer is valid. following
call stack will be seen
---- 8< ----
RIP: 0010:[<ffffffffa02ccadc>] [<ffffffffa02ccadc>] qla2x00_init_rings+0xdc/0x320 [qla2xxx]
RSP: 0018:ffff880429447dd8 EFLAGS: 00010082
....
Call Trace:
[<ffffffffa02ceb40>] qla2x00_abort_isp+0x170/0x6b0 [qla2xxx]
[<ffffffffa02c6f77>] qla2x00_do_dpc+0x357/0x7f0 [qla2xxx]
[<ffffffffa02c6c20>] ? qla2x00_relogin+0x260/0x260 [qla2xxx]
[<ffffffff8107d2c9>] kthread+0xc9/0xe0
[<ffffffff8107d200>] ? flush_kthread_worker+0x90/0x90
[<ffffffff8172cc6f>] ret_from_fork+0x3f/0x70
[<ffffffff8107d200>] ? flush_kthread_worker+0x90/0x90
---- 8< ----
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
99% of the time the ATIOQ has SCSI command. The other 1% of time
is something else. Most of the time this interrupt does not need
to hold the hardware_lock. We're moving the ATIO interrupt thread
to a different lock to reduce lock contention.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
queue work element to specific process lessen cache miss
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds interface to send explicit LOGO
explicit LOGO using using ELS commands from driver.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of resetting the adapter wait for the login to timeout
and retry. Resetting the adapter can cause extended path recovery
times.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
If an SRB is NULL but the handle is in range just drop the
command instead of also resetting the adapter. If the handle
is in range then the command was valid at some point and may
have been aborted. Resetting the adapter can lead to extended
recovery times in this case.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
When we get logged out, mark the port lost and set dpc flag for relogin.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Whether htonl() or __constant_htonl() is used, if the argument
is a constant the conversion happens at compile time. Hence leave
out the __constant_ prefix for this and other endianness
conversion functions. This improves source code readability.
[jejb: checkpatch fixes]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Detected these variables by building with W=1.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Commit f3ddac1918 ("[SCSI] qla2xxx:
Disable adapter when we encounter a PCI disconnect.") has introduced a
code that disables the board, releasing some resources, when reading
0xffffffff.
In case this happens when there is an EEH, this read will trigger EEH
detection and set PCI channel offline. EEH will be able to recover the
card from this state by doing a reset, so it's a better option than
simply disabling the card.
Since eeh_check_failure will mark the channel as offline before
returning the read value, in case there really was an EEH, we can simply
check for pci_channel_offline, preventing the board_disable code from
running if it's true.
Without this patch, EEH code will try to access those same resources
that board_disable will try to free. This race can cause EEH recovery to
fail.
[ 504.370577] EEH: Notify device driver to resume
[ 504.370580] qla2xxx [0001:07:00.0]-9002:2: The device failed to resume I/O from slot/link_reset.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
For FA-WWPN is enabled port, if NPIV created on that port and,
if port link is brought down, then WWPN was restored from flash for both
physical and NPIV port. This will result in NPIV port and physical port
sharing same WWPN. Any application refreshing ports information will
not be able to scan NPIV port because of this behavior. So while restoring WWPN,
only restore physical port WWPN.
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
On some vendor switches, when switch port is toggled (down /up),
then in some condition driver tries to configure virtual port,
before FW is actually in ready state to process any commands on wire.
At this time, configuring virtual port can fail. Add fix in driver
to make driver wait, for FW to be ready state before
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
For FA-WWPN capable device, ISP2031 and ISP27XX, when loop
dead is detected by a driver, restore WWPN from NVRAM.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Parse the retry delay timer field from the FCP response data and if:
- It is not zero
- The SCSI status is busy or queue full
return SCSI_MLQUEUE_TARGET_BUSY for the number of milliseconds specified
in the retry delay timer field.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add support for the D-port (diagnostic port) fabric switch feature.
(Fabric Switch initiates loopback style port testing)
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Semaphore register does not exist for ISPFx00.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The PCI register read checking introduced in commit fe1b806f4f
("qla2xxx: Disable adapter when we encounter a PCI disconnect") is
active during driver probe. Hold off scheduling any board removal until
the driver probe has completed. This ensures that the the board_disable
work structure is initialized and more importantly, avoids racing
qla2x00_probe_one.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Bart Van Assche