My UEK-derived config has 1030 files depending on pagemap.h before this
change. Afterwards, just 326 files need to be rebuilt when I touch
pagemap.h. I think blkdev.h is probably included too widely, but
untangling that dependency is harder and this solves my problem. x86
allmodconfig builds, but there may be implicit include problems on other
architectures.
Link: https://lkml.kernel.org/r/20210309195747.283796-1-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Dan Williams <dan.j.williams@intel.com> [nvdimm]
Acked-by: Jens Axboe <axboe@kernel.dk> [block]
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Coly Li <colyli@suse.de> [bcache]
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> [scsi]
Reviewed-by: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In null_init, null_add_dev(dev) is called.
In null_add_dev, it calls null_free_zoned_dev(dev) to free dev->zones
via kvfree(dev->zones) in out_cleanup_zone branch and returns err.
Then null_init accept the err code and then calls null_free_dev(dev).
But in null_free_dev(dev), dev->zones is freed again by
null_free_zoned_dev().
My patch set dev->zones to NULL in null_free_zoned_dev() after
kvfree(dev->zones) is called, to avoid the double free.
Fixes: 2984c8684f ("nullb: factor disk parameters")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Link: https://lore.kernel.org/r/20210426143229.7374-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Prior to commit 4a8c31a1c6 ("xen/blkback: rework connect_ring() to avoid
inconsistent xenstore 'ring-page-order' set by malicious blkfront"), the
behaviour of xen-blkback when connecting to a frontend was:
- read 'ring-page-order'
- if not present then expect a single page ring specified by 'ring-ref'
- else expect a ring specified by 'ring-refX' where X is between 0 and
1 << ring-page-order
This was correct behaviour, but was broken by the afforementioned commit to
become:
- read 'ring-page-order'
- if not present then expect a single page ring (i.e. ring-page-order = 0)
- expect a ring specified by 'ring-refX' where X is between 0 and
1 << ring-page-order
- if that didn't work then see if there's a single page ring specified by
'ring-ref'
This incorrect behaviour works most of the time but fails when a frontend
that sets 'ring-page-order' is unloaded and replaced by one that does not
because, instead of reading 'ring-ref', xen-blkback will read the stale
'ring-ref0' left around by the previous frontend will try to map the wrong
grant reference.
This patch restores the original behaviour.
Fixes: 4a8c31a1c6 ("xen/blkback: rework connect_ring() to avoid inconsistent xenstore 'ring-page-order' set by malicious blkfront")
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: Dongli Zhang <dongli.zhang@oracle.com>
Reviewed-by: "Roger Pau Monné" <roger.pau@citrix.com>
Link: https://lore.kernel.org/r/20210202175659.18452-1-paul@xen.org
Signed-off-by: Juergen Gross <jgross@suse.com>
While the maximum size of each ramdisk is defined either as a module
parameter, or compile time default, it's impossible to know how many pages
have currently been allocated by each ram%d device, since they're
allocated when used and never freed.
This patch creates a new directory at this location:
/sys/kernel/debug/ramdisk_pages/
which will contain a file named "ram%d" for each instantiated ramdisk on
the system. The file is read-only, and read() will output the number of
pages currently held by that ramdisk.
We lose track how much memory a ramdisk is using as pages once used are
simply recycled but never freed.
In instances where we exhaust the size of the ramdisk with a file that
exceeds it, encounter ENOSPC and delete the file for mitigation; df would
show decrease in used and increase in available blocks but the since we
have touched all pages, the memory footprint of the ramdisk does not
reflect the blocks used/available count
...
[root@localhost ~]# mkfs.ext2 /dev/ram15
mke2fs 1.45.6 (20-Mar-2020)
Creating filesystem with 4096 1k blocks and 1024 inodes
[root@localhost ~]# mount /dev/ram15 /mnt/ram15/
[root@localhost ~]# cat
/sys/kernel/debug/ramdisk_pages/ram15
58
[root@kerneltest008.06.prn3 ~]# df /dev/ram15
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/ram15 3963 31 3728 1% /mnt/ram15
[root@kerneltest008.06.prn3 ~]# dd if=/dev/urandom of=/mnt/ram15/test2
bs=1M count=5
dd: error writing '/mnt/ram15/test2': No space left on device
4+0 records in
3+0 records out
4005888 bytes (4.0 MB, 3.8 MiB) copied, 0.0446614 s, 89.7 MB/s
[root@kerneltest008.06.prn3 ~]# df /mnt/ram15/
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/ram15 3963 3960 0 100% /mnt/ram15
[root@kerneltest008.06.prn3 ~]# cat
/sys/kernel/debug/ramdisk_pages/ram15
1024
[root@kerneltest008.06.prn3 ~]# rm /mnt/ram15/test2
rm: remove regular file '/mnt/ram15/test2'? y
[root@kerneltest008.06.prn3 /var]# df /dev/ram15
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/ram15 3963 31 3728 1% /mnt/ram15
# Acutal memory footprint
[root@kerneltest008.06.prn3 /var]# cat
/sys/kernel/debug/ramdisk_pages/ram15
1024
...
This debugfs counter will always reveal the accurate number of
permanently allocated pages to the ramdisk.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
[cleaned up the !CONFIG_DEBUG_FS case and API changes for HEAD]
Signed-off-by: Kyle McMartin <jkkm@fb.com>
[rebased]
Signed-off-by: Saravanan D <saravanand@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Smatch complains that the "type > NUM_DISK_MINORS" should be >=
instead of >. We also need to subtract one from "type" at the start.
Fixes: bf9c0538e4 ("ataflop: use a separate gendisk for each media format")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The function uses "type" as an array index:
q = unit[drive].disk[type]->queue;
Unfortunately the bounds check on "type" isn't done until later in the
function. Fix this by moving the bounds check to the start.
Fixes: bf9c0538e4 ("ataflop: use a separate gendisk for each media format")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a couple
of warnings by explicitly adding a break statement instead of just
letting the code fall through to the next, and by adding a fallthrough
pseudo-keyword in places whre the code is intended to fall through.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
cppcheck report the following error:
rnbd/rnbd-clt-sysfs.c:522:36: error: The variable 'buf' is used both
as a parameter and as destination in snprintf(). The origin and
destination buffers overlap. Quote from glibc (C-library)
documentation
(http://www.gnu.org/software/libc/manual/html_mono/libc.html#Formatted-Output-Functions):
"If copying takes place between objects that overlap as a result of a
call to sprintf() or snprintf(), the results are undefined."
[sprintfOverlappingData]
Fix it by initializing the buf variable in the first snprintf call.
Fixes: 91f4acb280 ("block/rnbd-clt: support mapping two devices")
Signed-off-by: Dima Stepanov <dmitrii.stepanov@ionos.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Link: https://lore.kernel.org/r/20210419073722.15351-19-gi-oh.kim@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We always map with SZ_4K, so do not need max_segment_size.
Cc: Leon Romanovsky <leonro@nvidia.com>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20210419073722.15351-18-gi-oh.kim@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When an RTRS session state changes, the transport layer generates an event
to RNBD. Then RNBD will change the state of the RNBD client device
accordingly.
This commit add kobject_uevent when the RNBD device state changes. With
this udev rules can be configured to react accordingly.
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Link: https://lore.kernel.org/r/20210419073722.15351-17-gi-oh.kim@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
struct rtrs_srv is not used when handling rnbd_srv_rdma_ev messages, so
cleaned up
rdma_ev function pointer in rtrs_srv_ops also is changed.
Cc: Leon Romanovsky <leonro@nvidia.com>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Aleksei Marov <aleksei.marov@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20210419073722.15351-16-gi-oh.kim@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
RNBD can make double-queues for irq-mode and poll-mode.
For example, on 4-CPU system 8 request-queues are created,
4 for irq-mode and 4 for poll-mode.
If the IO has HIPRI flag, the block-layer will call .poll function
of RNBD. Then IO is sent to the poll-mode queue.
Add optional nr_poll_queues argument for map_devices interface.
To support polling of RNBD, RTRS client creates connections
for both of irq-mode and direct-poll-mode.
For example, on 4-CPU system it could've create 5 connections:
con[0] => user message (softirq cq)
con[1:4] => softirq cq
After this patch, it can create 9 connections:
con[0] => user message (softirq cq)
con[1:4] => softirq cq
con[5:8] => DIRECT-POLL cq
Cc: Leon Romanovsky <leonro@nvidia.com>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20210419073722.15351-14-gi-oh.kim@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When unloading the rnbd-clt module, it does not free a memory
including the filename of the symbolic link to /sys/block/rnbdX.
It is found by kmemleak as below.
unreferenced object 0xffff9f1a83d3c740 (size 16):
comm "bash", pid 736, jiffies 4295179665 (age 9841.310s)
hex dump (first 16 bytes):
21 64 65 76 21 6e 75 6c 6c 62 30 40 62 6c 61 00 !dev!nullb0@bla.
backtrace:
[<0000000039f0c55e>] 0xffffffffc0456c24
[<000000001aab9513>] kernfs_fop_write+0xcf/0x1c0
[<00000000db5aa4b3>] vfs_write+0xdb/0x1d0
[<000000007a2e2207>] ksys_write+0x65/0xe0
[<00000000055e280a>] do_syscall_64+0x50/0x1b0
[<00000000c2b51831>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20210419073722.15351-13-gi-oh.kim@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
clang static analysis reports this problem
rnbd-clt.c:1212:11: warning: Branch condition evaluates to a
garbage value
else if (!first)
^~~~~~
This is triggered in the find_and_get_or_create_sess() call
because the variable first is not initialized and the
earlier check is specifically for
if (sess == ERR_PTR(-ENOMEM))
This is false positive.
But the if-check can be reduced by initializing first to
false and then returning if the call to find_or_creat_sess()
does not set it to true. When it remains false, either
sess will be valid or not. The not case is caught by
find_and_get_or_create_sess()'s caller rnbd_clt_map_device()
sess = find_and_get_or_create_sess(...);
if (IS_ERR(sess))
return ERR_CAST(sess);
Since find_and_get_or_create_sess() initializes first to false
setting it in find_or_create_sess() is not needed.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Link: https://lore.kernel.org/r/20210419073722.15351-12-gi-oh.kim@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We changed the rnbd_srv_sess_dev_force_close to use try-lock
because rnbd_srv_sess_dev_force_close and process_msg_close
can generate a deadlock.
Now rnbd_srv_sess_dev_force_close would do nothing
if it fails to get the lock. So removing the force_close
file should be moved to after the lock. Or the force_close
file is removed but the others are not removed.
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20210419073722.15351-11-gi-oh.kim@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
They are defined with the same value and similar meaning, let's remove
one of them, then we can remove {WAIT,NOWAIT}.
Also change the type of 'wait' from 'int' to 'enum wait_type' to make
it clear.
Cc: Leon Romanovsky <leonro@nvidia.com>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Guoqing Jiang <guoqing.jiang@ionos.com>
Reviewed-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20210419073722.15351-9-gi-oh.kim@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We can use destroy_device directly since destroy_device_cb is just the
wrapper of destroy_device.
Signed-off-by: Guoqing Jiang <guoqing.jiang@ionos.com>
Reviewed-by: Danil Kipnis <danil.kipnis@ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Link: https://lore.kernel.org/r/20210419073722.15351-8-gi-oh.kim@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
No need to have it since we can call sysfs_remove_group in the
rnbd_clt_destroy_sysfs_files.
Then rnbd_clt_destroy_sysfs_files is paired with it's counterpart
rnbd_clt_create_sysfs_files.
Signed-off-by: Guoqing Jiang <guoqing.jiang@ionos.com>
Reviewed-by: Danil Kipnis <danil.kipnis@ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Link: https://lore.kernel.org/r/20210419073722.15351-7-gi-oh.kim@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It makes more sense to add gendisk in rnbd_clt_setup_gen_disk, instead
of do it in rnbd_clt_map_device.
Signed-off-by: Guoqing Jiang <guoqing.jiang@gmx.com>
Reviewed-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Link: https://lore.kernel.org/r/20210419073722.15351-6-gi-oh.kim@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove them since both sess and idx can be dereferenced from dev. And
sess is not used in the function.
Signed-off-by: Guoqing Jiang <guoqing.jiang@gmx.com>
Reviewed-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Link: https://lore.kernel.org/r/20210419073722.15351-5-gi-oh.kim@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove 'pathname' and 'sess' since we can dereference it from 'dev'.
Signed-off-by: Guoqing Jiang <guoqing.jiang@gmx.com>
Reviewed-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Link: https://lore.kernel.org/r/20210419073722.15351-4-gi-oh.kim@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
FLOPPY_SILENT_DCL_CLEAR is not defined anywhere and comes from pre-git
era. Just drop this undef. There is FD_SILENT_DCL_CLEAR which is really
used.
Signed-off-by: Denis Efremov <efremov@linux.com>
Link: https://lore.kernel.org/r/20210416083449.72700-6-efremov@linux.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use ST0 as 0 index for reply_buffer array. get_fdc_version() is the only
function that uses index 0 directly instead of the ST0 define.
Signed-off-by: Denis Efremov <efremov@linux.com>
Link: https://lore.kernel.org/r/20210416083449.72700-3-efremov@linux.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bio_list_copy_data is only used by pktcdvd, so move it there.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210412134658.2623190-2-hch@lst.de
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This will enable changing the virtual boundary of null blk devices. For
now, null blk devices didn't have any restriction on the scatter/gather
elements received from the block layer. Add a module parameter and a
configfs option that will control the virtual boundary. This will
enable testing the efficiency of the block layer bounce buffer in case
a suitable application will send discontiguous IO to the given device.
Initial testing with patched FIO showed the following results (64 jobs,
128 iodepth, 1 nullb device):
IO size READ (virt=false) READ (virt=true) Write (virt=false) Write (virt=true)
---------- ------------------- ----------------- ------------------- -------------------
1k 10.7M 8482k 10.8M 8471k
2k 10.4M 8266k 10.4M 8271k
4k 10.4M 8274k 10.3M 8226k
8k 10.2M 8131k 9800k 7933k
16k 9567k 7764k 8081k 6828k
32k 8865k 7309k 5570k 5153k
64k 7695k 6586k 2682k 2617k
128k 5346k 5489k 1320k 1296k
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Link: https://lore.kernel.org/r/20210412095523.278632-1-mgurtovoy@nvidia.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Guobin Huang <huangguobin4@huawei.com>
Link: https://lore.kernel.org/r/1617710988-49205-1-git-send-email-huangguobin4@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
swim3 only uses the virtual address of a bio to stash it into the data
transfer using virt_to_bus. But the ppc32 virt_to_bus just uses the
physical address with an offset. Replace virt_to_bus with a local hack
that performs the equivalent transformation and stop asking for block
layer bounce buffering.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210406061839.811588-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Always use the track buffer that is already used for addresses outside
the 16MB address capability of the floppy controller. This allows to
remove a lot of code that relies on kernel virtual addresses. With
this gone there is just a single place left that looks at the bio,
which can be converted to memcpy_{from,to}_page, thus removing the need
for the extra block-layer bounce buffering for highmem pages.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210406061755.811522-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
m68k doesn't support highmem, so don't bother enabling the block layer
bounce buffer code. Just for safety throw in a depend on !HIGHMEM.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210406061725.811389-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fixes the following W=1 kernel build warning(s):
from drivers/block/drbd/drbd_nl.c:24:
drivers/block/drbd/drbd_nl.c: In function ‘drbd_adm_attach’:
drivers/block/drbd/drbd_nl.c:1968:10: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion]
drivers/block/drbd/drbd_nl.c:930: warning: Function parameter or member 'flags' not described in 'drbd_determine_dev_size'
drivers/block/drbd/drbd_nl.c:930: warning: Function parameter or member 'rs' not described in 'drbd_determine_dev_size'
drivers/block/drbd/drbd_nl.c:1148: warning: Function parameter or member 'dc' not described in 'drbd_check_al_size'
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: drbd-dev@lists.linbit.com
Cc: linux-block@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210312105530.2219008-12-lee.jones@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fixes the following W=1 kernel build warning(s):
drivers/block/xen-blkfront.c:1960: warning: Function parameter or member 'dev' not described in 'blkfront_probe'
drivers/block/xen-blkfront.c:1960: warning: Function parameter or member 'id' not described in 'blkfront_probe'
drivers/block/xen-blkfront.c:1960: warning: expecting prototype for Allocate the basic(). Prototype was for blkfront_probe() instead
drivers/block/xen-blkfront.c:2085: warning: Function parameter or member 'dev' not described in 'blkfront_resume'
drivers/block/xen-blkfront.c:2085: warning: expecting prototype for or a backend(). Prototype was for blkfront_resume() instead
drivers/block/xen-blkfront.c:2444: warning: wrong kernel-doc identifier on line:
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: "Roger Pau Monné" <roger.pau@citrix.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: xen-devel@lists.xenproject.org
Cc: linux-block@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Link: https://lore.kernel.org/r/20210312105530.2219008-11-lee.jones@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fixes the following W=1 kernel build warning(s):
drivers/block/drbd/drbd_receiver.c:1641: warning: Function parameter or member 'op' not described in 'drbd_submit_peer_request'
drivers/block/drbd/drbd_receiver.c:1641: warning: Function parameter or member 'op_flags' not described in 'drbd_submit_peer_request'
drivers/block/drbd/drbd_receiver.c:1641: warning: Function parameter or member 'fault_type' not described in 'drbd_submit_peer_request'
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: drbd-dev@lists.linbit.com
Cc: linux-block@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210312105530.2219008-10-lee.jones@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fixes the following W=1 kernel build warning(s):
drivers/block/drbd/drbd_main.c:278: warning: Function parameter or member 'connection' not described in 'tl_clear'
drivers/block/drbd/drbd_main.c:278: warning: Excess function parameter 'device' description in 'tl_clear'
drivers/block/drbd/drbd_main.c:489: warning: Function parameter or member 'cpu_mask' not described in 'drbd_calc_cpu_mask'
drivers/block/drbd/drbd_main.c:528: warning: Excess function parameter 'device' description in 'drbd_thread_current_set_cpu'
drivers/block/drbd/drbd_main.c:549: warning: Function parameter or member 'connection' not described in 'drbd_header_size'
drivers/block/drbd/drbd_main.c:1204: warning: Function parameter or member 'device' not described in 'send_bitmap_rle_or_plain'
drivers/block/drbd/drbd_main.c:1204: warning: Function parameter or member 'c' not described in 'send_bitmap_rle_or_plain'
drivers/block/drbd/drbd_main.c:1335: warning: Function parameter or member 'peer_device' not described in '_drbd_send_ack'
drivers/block/drbd/drbd_main.c:1335: warning: Excess function parameter 'device' description in '_drbd_send_ack'
drivers/block/drbd/drbd_main.c:1379: warning: Function parameter or member 'peer_device' not described in 'drbd_send_ack'
drivers/block/drbd/drbd_main.c:1379: warning: Excess function parameter 'device' description in 'drbd_send_ack'
drivers/block/drbd/drbd_main.c:1892: warning: Function parameter or member 'connection' not described in 'drbd_send_all'
drivers/block/drbd/drbd_main.c:1892: warning: Function parameter or member 'sock' not described in 'drbd_send_all'
drivers/block/drbd/drbd_main.c:1892: warning: Function parameter or member 'buffer' not described in 'drbd_send_all'
drivers/block/drbd/drbd_main.c:1892: warning: Function parameter or member 'size' not described in 'drbd_send_all'
drivers/block/drbd/drbd_main.c:1892: warning: Function parameter or member 'msg_flags' not described in 'drbd_send_all'
drivers/block/drbd/drbd_main.c:3525: warning: Function parameter or member 'flags' not described in 'drbd_queue_bitmap_io'
drivers/block/drbd/drbd_main.c:3563: warning: Function parameter or member 'flags' not described in 'drbd_bitmap_io'
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: drbd-dev@lists.linbit.com
Cc: linux-block@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210312105530.2219008-9-lee.jones@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fixes the following W=1 kernel build warning(s):
from drivers/block/drbd/drbd_nl.c:24:
drivers/block/drbd/drbd_nl.c: In function ‘drbd_adm_set_role’:
drivers/block/drbd/drbd_nl.c:793:11: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion]
drivers/block/drbd/drbd_nl.c:795:11: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion]
drivers/block/drbd/drbd_nl.c: In function ‘drbd_adm_attach’:
drivers/block/drbd/drbd_nl.c:1965:10: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion]
drivers/block/drbd/drbd_nl.c: In function ‘drbd_adm_connect’:
drivers/block/drbd/drbd_nl.c:2690:10: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion]
drivers/block/drbd/drbd_nl.c: In function ‘drbd_adm_disconnect’:
drivers/block/drbd/drbd_nl.c:2803:11: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion]
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: drbd-dev@lists.linbit.com
Cc: linux-block@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210312105530.2219008-8-lee.jones@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
[P_RETRY_WRITE] is initialised more than once.
Fixes the following W=1 kernel build warning(s):
drivers/block/drbd/drbd_main.c: In function ‘cmdname’:
drivers/block/drbd/drbd_main.c:3660:22: warning: initialized field overwritten [-Woverride-init]
drivers/block/drbd/drbd_main.c:3660:22: note: (near initialization for ‘cmdnames[44]’)
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: drbd-dev@lists.linbit.com
Cc: linux-block@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210312105530.2219008-7-lee.jones@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fixes the following W=1 kernel build warning(s):
drivers/block/drbd/drbd_receiver.c:265: warning: Function parameter or member 'peer_device' not described in 'drbd_alloc_pages'
drivers/block/drbd/drbd_receiver.c:265: warning: Excess function parameter 'device' description in 'drbd_alloc_pages'
drivers/block/drbd/drbd_receiver.c:1362: warning: Function parameter or member 'connection' not described in 'drbd_may_finish_epoch'
drivers/block/drbd/drbd_receiver.c:1362: warning: Excess function parameter 'device' description in 'drbd_may_finish_epoch'
drivers/block/drbd/drbd_receiver.c:1451: warning: Function parameter or member 'resource' not described in 'drbd_bump_write_ordering'
drivers/block/drbd/drbd_receiver.c:1451: warning: Function parameter or member 'bdev' not described in 'drbd_bump_write_ordering'
drivers/block/drbd/drbd_receiver.c:1451: warning: Excess function parameter 'connection' description in 'drbd_bump_write_ordering'
drivers/block/drbd/drbd_receiver.c:1643: warning: Function parameter or member 'op' not described in 'drbd_submit_peer_request'
drivers/block/drbd/drbd_receiver.c:1643: warning: Function parameter or member 'op_flags' not described in 'drbd_submit_peer_request'
drivers/block/drbd/drbd_receiver.c:1643: warning: Function parameter or member 'fault_type' not described in 'drbd_submit_peer_request'
drivers/block/drbd/drbd_receiver.c:1643: warning: Excess function parameter 'rw' description in 'drbd_submit_peer_request'
drivers/block/drbd/drbd_receiver.c:3055: warning: Function parameter or member 'peer_device' not described in 'drbd_asb_recover_0p'
drivers/block/drbd/drbd_receiver.c:3138: warning: Function parameter or member 'peer_device' not described in 'drbd_asb_recover_1p'
drivers/block/drbd/drbd_receiver.c:3195: warning: Function parameter or member 'peer_device' not described in 'drbd_asb_recover_2p'
drivers/block/drbd/drbd_receiver.c:4684: warning: Function parameter or member 'peer_device' not described in 'receive_bitmap_plain'
drivers/block/drbd/drbd_receiver.c:4684: warning: Function parameter or member 'size' not described in 'receive_bitmap_plain'
drivers/block/drbd/drbd_receiver.c:4684: warning: Function parameter or member 'p' not described in 'receive_bitmap_plain'
drivers/block/drbd/drbd_receiver.c:4684: warning: Function parameter or member 'c' not described in 'receive_bitmap_plain'
drivers/block/drbd/drbd_receiver.c:4738: warning: Function parameter or member 'peer_device' not described in 'recv_bm_rle_bits'
drivers/block/drbd/drbd_receiver.c:4738: warning: Function parameter or member 'p' not described in 'recv_bm_rle_bits'
drivers/block/drbd/drbd_receiver.c:4738: warning: Function parameter or member 'c' not described in 'recv_bm_rle_bits'
drivers/block/drbd/drbd_receiver.c:4738: warning: Function parameter or member 'len' not described in 'recv_bm_rle_bits'
drivers/block/drbd/drbd_receiver.c:4807: warning: Function parameter or member 'peer_device' not described in 'decode_bitmap_c'
drivers/block/drbd/drbd_receiver.c:4807: warning: Function parameter or member 'p' not described in 'decode_bitmap_c'
drivers/block/drbd/drbd_receiver.c:4807: warning: Function parameter or member 'c' not described in 'decode_bitmap_c'
drivers/block/drbd/drbd_receiver.c:4807: warning: Function parameter or member 'len' not described in 'decode_bitmap_c'
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: drbd-dev@lists.linbit.com
Cc: linux-block@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210312105530.2219008-6-lee.jones@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fixes the following W=1 kernel build warning(s):
drivers/block/drbd/drbd_state.c:913: warning: Function parameter or member 'connection' not described in 'is_valid_soft_transition'
drivers/block/drbd/drbd_state.c:913: warning: Excess function parameter 'device' description in 'is_valid_soft_transition'
drivers/block/drbd/drbd_state.c:1054: warning: Function parameter or member 'warn' not described in 'sanitize_state'
drivers/block/drbd/drbd_state.c:1054: warning: Excess function parameter 'warn_sync_abort' description in 'sanitize_state'
drivers/block/drbd/drbd_state.c:1703: warning: Function parameter or member 'state_change' not described in 'after_state_ch'
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: drbd-dev@lists.linbit.com
Cc: linux-block@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210312105530.2219008-5-lee.jones@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fixes the following W=1 kernel build warning(s):
drivers/block/mtip32xx/mtip32xx.c: In function ‘mtip_standby_immediate’:
drivers/block/mtip32xx/mtip32xx.c:1216:16: warning: variable ‘start’ set but not used [-Wunused-but-set-variable]
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210312105530.2219008-4-lee.jones@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fixes the following W=1 kernel build warning(s):
drivers/block/drbd/drbd_interval.c:11: warning: Function parameter or member 'node' not described in 'interval_end'
drivers/block/drbd/drbd_interval.c:26: warning: Function parameter or member 'root' not described in 'drbd_insert_interval'
drivers/block/drbd/drbd_interval.c:26: warning: Function parameter or member 'this' not described in 'drbd_insert_interval'
drivers/block/drbd/drbd_interval.c:70: warning: Function parameter or member 'root' not described in 'drbd_contains_interval'
drivers/block/drbd/drbd_interval.c:96: warning: Function parameter or member 'root' not described in 'drbd_remove_interval'
drivers/block/drbd/drbd_interval.c:96: warning: Function parameter or member 'this' not described in 'drbd_remove_interval'
drivers/block/drbd/drbd_interval.c:113: warning: Function parameter or member 'root' not described in 'drbd_find_overlap'
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: drbd-dev@lists.linbit.com
Cc: linux-block@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210312105530.2219008-3-lee.jones@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAmBnh84QHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpubkD/0Y+l3cecjzds3RnRXEXYsRFBKGfK6c7Uuu
QVCrlRp6tKPmBoDLQyl95Mg0e44pR4s3Bw5W4j9GmJtVyNVzC2x3dqXn3uXSFca/
KU+4GIzl2VIXS5Pn90GLE6/xw3FtVy8w2c6V3g4jkLR29bexPdO4s57cohxKR9kL
ZU+icCag9RlNIYkuB79Wy6Y3/m41L5WRkMGiMb0sJS9Q+k+zetZNIeNIxWn4E1zF
qWymdyBFx31qL8/2ZmRwb8XzF5qE2XimXz1a7ZX754zyR/Ry5rGc0h+JjqgUhSV9
wM2gLlMNEP+k+8DOU9ACYdff18P6b+RZ8mJnGZjZseAut1qJXonVtgDoWX7mEs9+
8Gl+n18TYpKEfzLiOOOtu/xeZYMjp0MUjO6iHTpzRfqBjKNoZGTuz0wGC5nX/ZYI
y5QWifI0NmMmTPDJpH6nVYzqDLbEZzcMz6WeOfhKQ/yv7gOxj+BFGJ3olJ+DAx8c
e6HDPa/WkC0iqie5cpzYjmve0HrKJADMMrRRWGRkgmOZ8uAaSS17rZExg1CICr8I
bOVYsrPsg8ErKVvzlx/DK6EfhNrw0+Db7paYccl2a3pXx/T8iHmW3RSqn7jMrhA1
7QPOCUMKuWuaOupWJWw25gxNS3viJa57/hxMG1nvAgpJx6QvBNaLrwcIWXO1cfrp
boe/UFnftg==
=8odY
-----END PGP SIGNATURE-----
Merge tag 'block-5.12-2021-04-02' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Remove comment that never came to fruition in 22 years of development
(Christoph)
- Remove unused request flag (Christoph)
- Fix for null_blk fake timeout handling (Damien)
- Fix for IOCB_NOWAIT being ignored for O_DIRECT on raw bdevs (Pavel)
- Error propagation fix for multiple split bios (Yufen)
* tag 'block-5.12-2021-04-02' of git://git.kernel.dk/linux-block:
block: remove the unused RQF_ALLOCED flag
block: update a few comments in uapi/linux/blkpg.h
block: don't ignore REQ_NOWAIT for direct IO
null_blk: fix command timeout completion handling
block: only update parent bi_status when bio fail
Memory backed or zoned null block devices may generate actual request
timeout errors due to the submission path being blocked on memory
allocation or zone locking. Unlike fake timeouts or injected timeouts,
the request submission path will call blk_mq_complete_request() or
blk_mq_end_request() for these real timeout errors, causing a double
completion and use after free situation as the block layer timeout
handler executes blk_mq_rq_timed_out() and __blk_mq_free_request() in
blk_mq_check_expired(). This problem often triggers a NULL pointer
dereference such as:
BUG: kernel NULL pointer dereference, address: 0000000000000050
RIP: 0010:blk_mq_sched_mark_restart_hctx+0x5/0x20
...
Call Trace:
dd_finish_request+0x56/0x80
blk_mq_free_request+0x37/0x130
null_handle_cmd+0xbf/0x250 [null_blk]
? null_queue_rq+0x67/0xd0 [null_blk]
blk_mq_dispatch_rq_list+0x122/0x850
__blk_mq_do_dispatch_sched+0xbb/0x2c0
__blk_mq_sched_dispatch_requests+0x13d/0x190
blk_mq_sched_dispatch_requests+0x30/0x60
__blk_mq_run_hw_queue+0x49/0x90
process_one_work+0x26c/0x580
worker_thread+0x55/0x3c0
? process_one_work+0x580/0x580
kthread+0x134/0x150
? kthread_create_worker_on_cpu+0x70/0x70
ret_from_fork+0x1f/0x30
This problem very often triggers when running the full btrfs xfstests
on a memory-backed zoned null block device in a VM with limited amount
of memory.
Avoid this by executing blk_mq_complete_request() in null_timeout_rq()
only for commands that are marked for a fake timeout completion using
the fake_timeout boolean in struct null_cmd. For timeout errors injected
through debugfs, the timeout handler will execute
blk_mq_complete_request()i as before. This is safe as the submission
path does not execute complete requests in this case.
In null_timeout_rq(), also make sure to set the command error field to
BLK_STS_TIMEOUT and to propagate this error through to the request
completion.
Reported-by: Johannes Thumshirn <Johannes.Thumshirn@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Tested-by: Johannes Thumshirn <Johannes.Thumshirn@wdc.com>
Reviewed-by: Johannes Thumshirn <Johannes.Thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210331225244.126426-1-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Matthew Wilcox (Oracle)