The variable is_capture is initialized but never used otherwise.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
identifier i;
constant C;
@@
(
extern T i;
|
- T i;
<+... when != i
- i = C;
...+>
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* removing the hack with NON_AKM ak4xxx type
* support for card-specific flags in ak4114_stats
* definition of the flags for corresponding cards
Signed-off-by: Pavel Hofman <dustin@seznam.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We want to have snd_card_set_dev() in _probe(), but not a second one in
snd_ml403_ac97cr_create().
Signed-off-by: Joachim Foerster <JOFT@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AK4114 on Juli@ has the SPDIF input sample rate detection and
causes errors when an incompatible sample rate is chosen.
The patch adds the open hook to check the current rate and limit
the hw constraints.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The docking station headphone output had no audio and jack sense
was not considered.
Jack information from the laptop itself and the dock are combined, as
the dock does not obscure the connector.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hda-intel driver has a problem at power-off on ASUS P5AD2.
It's caused when the position-buffer is enabled -- most likely a
hardware-specific problem.
This patch adds a quirk to avoid the unnecessary enablement of
position-buffer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Map 3stack-6ch-dig ALC662 model for Asus P5GC-MX.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently ALC662 doesn't suport amp mute for AmpOut in nids 0x02, 0x03,
0x04 (see block diagram in ALC662 datasheet page 3, does M correspond to
mute?). The result is that currently mute for "Front Playback Switch",
"Surround Playback Switch", "Center Playback Switch" and "LFE Playback
Switch" mixer items doesn't work (tested on Asus P5GC-MX motherboard
with 3stack-6ch model).
The solution I found for this is to mute the proper inputs in 0x0c,
0x0d, 0x0e audio mixers.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, the headphone controls are created as Master wrongly in
some cases, and this prevents the virtual master controls.
The patch fixes the problem by simply using "Headphone" always for
headphone controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed issue on some laptops that if the Master mixer and DAC mixers are
turned all the way up that will cause distortion. This is fixed by limiting
the max volume with the volume knob nid.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Improved ALC262 ultra model for Samsung Q1 Ultra series.
- clean up mixers
- support of input from HP jack as a mic
- add quirk for Q1 EL
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_pcm_lib_preallocate_free_for_all() is called from snd_pcm_free() just
after calling the private_free routine. So there should be no need to call
it in driver's private_free routine.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
aw2-tsl.h should be rather a C file to be included since it's referred
only in aw2-saa6146.c and includes a table data.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The default capture source should be the mic which is 0x01 on this model.
In addition to that the change to VREF50 allows for higher capture volume.
Signed-off-by: Michael Gruber <lists.mg@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Changed so that internal speakers point to the Front mixer instead of Surround.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for monaural playback to at73c213 driver. The sound will be apear
on L-channel. Tested on AT91SAM9260-EK.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The clk_round_rate() and clk_set_rate() will return int, so not store thier
return value to unsigned long variable. This bug hides real error on these
API.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for the Toshiba Equium L30 laptop and renames the mixer
controls to match Laptop usages.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
if (...) BUG(); should be replaced with BUG_ON(...) when the test has no
side-effects to allow a definition of BUG_ON that drops the code completely.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@ disable unlikely @ expression E,f; @@
(
if (<... f(...) ...>) { BUG(); }
|
- if (unlikely(E)) { BUG(); }
+ BUG_ON(E);
)
@@ expression E,f; @@
(
if (<... f(...) ...>) { BUG(); }
|
- if (E) { BUG(); }
+ BUG_ON(E);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Added the internal mic as a capture source item for ALC268 acer model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the Device IDs of nvidia MCP79 HD audio controller to hda_intel.c
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the model laptop-hpsense use the 0x12 as ExtMic,
and use 0x14 as Internal IntMic.
But the hp530 only have one ExtMic, the Pin widget is 0x14.
In this patch, I changed the mixer item for them.
I still reserved the IntMic item, it will be helpful if
other machine may use this model.
ALSA bug#3821.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no suitable model for Pi2515.
This model is to support it. ALSA bug#3800.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
NEC S970 has no sound in the internal speakers when autodetection is
used.
With targa-dig model, there is sound in the speakers and it gets
correctly muted when pluging headphones.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- make pcsp_start_timer_tasklet static
- remove redundant includes. <asm/i8253.h> is not available on all platforms.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no suitable model for M720R (ALSA bug#3781).
This patch is to support HP jack-sensing and mixer.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sparc32:
sound/pci/hda/hda_intel.c: In function 'azx_create':
sound/pci/hda/hda_intel.c:1838: error: 'DMA_64BIT_MASK' undeclared (first use in this function)
sound/pci/hda/hda_intel.c:1838: error: (Each undeclared identifier is reported only once
sound/pci/hda/hda_intel.c:1838: error: for each function it appears in.)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
GTA02 device has a speaker between LOUT2 & ROUT2 and in this mode ROUT2
needs to be inverted. This patch adds a mixer control for this.
Signed-off-by: Graeme Gregory <graeme@openmoko.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added core_init[] for several 92hd73xxx laptops.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power management can't be enabled on fixed ports, since the presence
will always return false and prevent output.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the array declaration to hda_codec.c where it is used and add includes
where the individual presets are declared.
Fixes the following sparse warnings:
sound/pci/hda/patch_realtek.c:13744:25: warning: symbol 'snd_hda_preset_realtek' was not declared. Should it be static?
sound/pci/hda/patch_cmedia.c:729:25: warning: symbol 'snd_hda_preset_cmedia' was not declared. Should it be static?
sound/pci/hda/patch_analog.c:3656:25: warning: symbol 'snd_hda_preset_analog' was not declared. Should it be static?
sound/pci/hda/patch_sigmatel.c:3995:25: warning: symbol 'snd_hda_preset_sigmatel' was not declared. Should it be static?
sound/pci/hda/patch_si3054.c:286:25: warning: symbol 'snd_hda_preset_si3054' was not declared. Should it be static?
sound/pci/hda/patch_atihdmi.c:156:25: warning: symbol 'snd_hda_preset_atihdmi' was not declared. Should it be static?
sound/pci/hda/patch_conexant.c:1721:25: warning: symbol 'snd_hda_preset_conexant' was not declared. Should it be static?
sound/pci/hda/patch_via.c:1962:25: warning: symbol 'snd_hda_preset_via' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Temp variable in the loop shadows the second argument (which is otherwise
unused in this function). Change this to defcfg as it is used to hold
the default config.
sound/pci/hda/patch_sigmatel.c:2759:18: warning: symbol 'cfg' shadows an earlier one
sound/pci/hda/patch_sigmatel.c:2734:26: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In both cases we are passing around the substream number, use
sub_num for this.
sound/pci/riptide/riptide.c:1633:6: warning: symbol 'index' shadows an earlier one
sound/pci/riptide/riptide.c:121:12: originally declared here
sound/pci/riptide/riptide.c:1673:6: warning: symbol 'index' shadows an earlier one
sound/pci/riptide/riptide.c:121:12: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Inner loop redeclares err with u32 rather than int, stupid fix here
is to change the inner err to err2.
sound/pci/pcxhr/pcxhr_core.c:1008:8: warning: symbol 'err' shadows an earlier one
sound/pci/pcxhr/pcxhr_core.c:983:6: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use priv_idx as an identifier.
sound/pci/oxygen/virtuoso.c:277:15: warning: symbol 'index' shadows an earlier one
sound/pci/oxygen/virtuoso.c:56:12: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In all four case, adding a private value to the iooff index,
call it priv_idx.
sound/pci/ice1712/ice1712.c:1300:6: warning: symbol 'index' shadows an earlier one
sound/pci/ice1712/ice1712.c:85:12: originally declared here
sound/pci/ice1712/ice1712.c:1312:6: warning: symbol 'index' shadows an earlier one
sound/pci/ice1712/ice1712.c:85:12: originally declared here
sound/pci/ice1712/ice1712.c:1338:6: warning: symbol 'index' shadows an earlier one
sound/pci/ice1712/ice1712.c:85:12: originally declared here
sound/pci/ice1712/ice1712.c:1350:6: warning: symbol 'index' shadows an earlier one
sound/pci/ice1712/ice1712.c:85:12: originally declared here
[tiwai - fixed coding issues as well]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
enable in these contexts refers specifically to intr enable, as
per the two functions it is found in. Use intr_enable instead.
sound/pci/emu10k1/emu10k1x.c:330:15: warning: symbol 'enable' shadows an earlier one
sound/pci/emu10k1/emu10k1x.c:53:12: originally declared here
sound/pci/emu10k1/emu10k1x.c:341:15: warning: symbol 'enable' shadows an earlier one
sound/pci/emu10k1/emu10k1x.c:53:12: originally declared here
instead of shadowing, use cap_voice as we test for the capture
voice in this statement.
sound/pci/emu10k1/emu10k1x.c:798:25: warning: symbol 'pvoice' shadows an earlier one
sound/pci/emu10k1/emu10k1x.c:787:24: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reading regs from the fpga into an int instead of a u32, trivial
fix.
sound/pci/emu10k1/emuproc.c:422:34: warning: incorrect type in argument 3 (different signedness)
sound/pci/emu10k1/emuproc.c:422:34: expected unsigned int [usertype] *value
sound/pci/emu10k1/emuproc.c:422:34: got int *<noident>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/pci/au88x0/au88x0_pcm.c:508:15: warning: Using plain integer as NULL pointer
Also some small codingstyle fixes.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
when the time interval for a period is smaller than kernel HZ, then
snd-aloop and snd-dummy cannot call snd_pcm_period_elapsed as fast enough
annymore. this happens for example with games. but the app still needs to
see, that the buffer actually did go further, which is provided by these
patches.
Signed-off-by: Ahmet İnan <ainan <at> mathematik.uni-freiburg.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the variable err to _err within the ADD_CTLS macro to avoid
shadowing the local variable.
sound/pci/ca0106/ca0106_mixer.c:710:2: warning: symbol 'err' shadows an earlier one
sound/pci/ca0106/ca0106_mixer.c:663:6: originally declared here
sound/pci/ca0106/ca0106_mixer.c:712:3: warning: symbol 'err' shadows an earlier one
sound/pci/ca0106/ca0106_mixer.c:663:6: originally declared here
sound/pci/ca0106/ca0106_mixer.c:721:3: warning: symbol 'err' shadows an earlier one
sound/pci/ca0106/ca0106_mixer.c:663:6: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
change to intr_enable as per the two functions it is defined in.
sound/pci/ca0106/ca0106_main.c:438:15: warning: symbol 'enable' shadows an earlier one
sound/pci/ca0106/ca0106_main.c:159:12: originally declared here
sound/pci/ca0106/ca0106_main.c:449:15: warning: symbol 'enable' shadows an earlier one
sound/pci/ca0106/ca0106_main.c:159:12: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
enable is used to test for whether or not spdif should be enabled,
change to spdif_enable.
sound/pci/ali5451/ali5451.c:1812:15: warning: symbol 'enable' shadows an earlier one
sound/pci/ali5451/ali5451.c:63:12: originally declared here
sound/pci/ali5451/ali5451.c:1840:27: warning: symbol 'enable' shadows an earlier one
sound/pci/ali5451/ali5451.c:63:12: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
err is always assigned before it is used, no need to declare another
inside the if statement.
sound/pci/ac97/ac97_pcm.c:577:7: warning: symbol 'err' shadows an earlier one
sound/pci/ac97/ac97_pcm.c:572:6: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
kernel style does assignment outside of if() block
sound/pci/rme96.c:1562:71: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
kernel style does assignment outside of if() statements.
sound/pci/rme32.c:1353:71: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
change id to elem_id as it is used to initialize each mixer element
sound/pci/maestro3.c:2071:25: warning: symbol 'id' shadows an earlier one
sound/pci/maestro3.c:67:13: originally declared here
index is used in each of these places to count over the dsp's memory,
change to the name dsp_index
sound/pci/maestro3.c:2572:9: warning: symbol 'index' shadows an earlier one
sound/pci/maestro3.c:66:12: originally declared here
sound/pci/maestro3.c:2604:9: warning: symbol 'index' shadows an earlier one
sound/pci/maestro3.c:66:12: originally declared here
[tiwai - fixed coding style issues as well]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
id was only used as a counter in a for loop, move the declaration
to where it is used and change it to i.
sound/pci/fm801.c:1288:6: warning: symbol 'id' shadows an earlier one
sound/pci/fm801.c:51:13: originally declared here
[tiwai - fixed a coding style issue as well]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
id is used when initializing the mixer elements, use elem_id here
instead.
sound/pci/es1968.c:1963:25: warning: symbol 'id' shadows an earlier one
sound/pci/es1968.c:129:13: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
index is incremented only when AC97_EI_SPDIF and then assigned to
the index field. Change the temporary name to is_spdif.
sound/pci/ens1370.c:1638:10: warning: symbol 'index' shadows an earlier one
sound/pci/ens1370.c:84:12: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A temporary variable for each mixer element is used in an initialization
loop, use the name elem_id.
sound/pci/cmipci.c:2747:26: warning: symbol 'id' shadows an earlier one
sound/pci/cmipci.c:56:13: originally declared here
[tiwai - fixed a coding style issue as well]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reduce the number of times to check for a non-empty Tx FIFO from 100 to
2 because there is no MPU-401 implementation that needs more than one or
two reads to determine the actual FIFO status.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
The bits indicating SPDIF frequency in the status register are not the same for
the 9632 than for the other cards, because it also supports 192kHz. A specific
bitmask has thus been added (used in hdsp_spdif_sample_rate()).
The 9632 does not seem to report external sample rates greater than 96kHz. In
this case, the best seems to report spdif rate when autosync reference is
spdif. This also required to move function hdsp_spdif_sample_rate().
Signed-off-by: Remy Bruno <remy.bruno@trinnov.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added logic to check if AUTO_PIN_FRONT_MIC is available for output
switch, if AUTO_PIN_MIC isn't.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some laptops have a internal analog microphone that is not setup by the BIOS.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added PCI_QUIRKS for laptop that have the 92HDxxx family of codecs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
STAC_DELL_BIOS quirks were setting the association value wrong
for port 0x0f, which prevented it from being included in hp_outs[].
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix issue on STAC927x codecs that first DAC was getting powered down
even if was being used.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialize the capture source properly for auto model.
It's especially important for cases that only mic is detected.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the beep volume control to ALC268 codec support code.
Since the codec doesn't return the correct AMP caps, we need to override
the value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use a private array for TLV entries of virtual master controls instead
of (supposed) static array. This cleans up the existing codes.
Also, now vmaster assumes the simple dB-range TLV that is the only type
it can handle.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the codes for virtual master controls to sound core part so that
not only hda-intel drivers can use it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the support of 8 channel sound for codecs that are known to work.
So far, only ALC850 is marked as a 8ch-support codec.
This fix is a modified version of the patch on ALSA BTS#2097 by
Martin Ellis:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=2097
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds __devinit to the functions used when probing. Will also reduce
the memory footprint a bit if CONFIG_HOTPLUG is not enabled.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the support of new AD codecs: AD1883, AD1884A, AD1984A and AD1984B.
These are almost compatible except for additional digital pins, etc.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds an ASoC driver for the WM9713 AC97 codec.
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC262 must have capsrc_nids defined as well as in ALC882.
Also, add a NULL check in alc882_mux_enum_put to avoid Oops.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The last patch for fixing the auto-config pin setting breaks the resume
due to a wrong use of snd_hda_codec_amp_stereo(). The code in the init
hook shouldn't touch the amp cache.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a new mixer switch to enable/disable the sharing of the default
PCM stream with analog and SPDIF outputs. When "IEC958 Default PCM"
switch is on, the PCM stream is routed both to analog and SPDIF outputs.
This is the behavior in the earlier version.
Turning this switch off has a merit for some codecs, though. Some codec
chips don't support 24bit formats for SPDIF but only for analog outputs.
In this case, you can use 24bit format by disabling this switch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes some bugs in the auto-configurator of Realtek codecs:
- add missing pin set-up for speaker pins
- fix the speaker auto-mute function not to conflict with the existing
"Speaker" mixer switch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In some cases, the BIOS sets up only the HP pins with different assoc
and sequence numbers, e.g. on FSC Esprimo with ALC262.
This patch adds a fix-up for such a case. When multiple HPs are defined
and no line-outs is found, the configurator tries to re-assign some pins
from HP list to line-out, judging from the sequence number.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implemented the auto-mic jack sensing for Samsung laptops with AD1986A
codec chip (model=laptop-eapd).
The hardware uses pin 0x1d and 0x1f for the internal and external
mics, respectively.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clean up the codes of the capture source selection for Realtek codecs.
Now using common helper functions with the new capsrc_nids field.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reprogram the speaker-pin setting at each HP pin plug to make sure
the spekaer auto-muting on AD1981HD hp model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I've just noticed that there are a handful of duplicate controls in the
ALC268 test model mixer. This patch (against alsa-driver 1.0.16) removes
them.
Signed-off-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
See ALSA bug#3327 for more details. Experimental.
Also fix support for M-Audio Delta 1010E - subdevice check.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The HD-audio hardware usually supports 64bit address for DMA and other
buffers. The patch enables the feature if supported.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On several laptops that have STAC9228 codecs have unused DACs,
this powers them down to a D3 state.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes the problems with Midi In on Hoontech/STA dsp24 cards, for example with
DSP2000 box, without restricting the box configurations available. Also adds
mpu_401 name strings.
Signed-off-by: Alan Horstmann <gineera@aspect135.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current scheme, PCM device numbers are assigned incrementally
in the order of codecs. This causes problems when the codec number
is irregular, e.g. codec #0 for HDMI and codec #1 for analog. Then
the HDMI becomes the first PCM, which is picked up as the default
output device. Unfortuantely this doesn't work well with normal
setups.
This patch introduced the fixed device numbers for the PCM types,
namely, analog, SPDIF, HDMI and modem. The PCM devices are assigned
according to the corresponding PCM type. After this patch, HDMI will
be always assigned to PCM #3, SPDIF to PCM #1, and the first analog
to PCM #0, etc.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added more fallbacks to OSS PHONEOUT mixer mapping. This corresponds
to the speaker output in general, so now "Mono" and "Speaker" are
assigned.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current code doesn't allow multiple SPDIF devices, and causes
errors when multiple SPDIF devices are found (e.g. SPDIF out and HDMI).
This patch allows multiple SPDIF devices by incrementing the index
automatically.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for the OQO Model 2 Ultra Mobile PC.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently you will see an empty "SoC Audio support for SuperH" menu
when building for other archs (example pxa).
This patch adds "depends on SUPERH" to remove that empty menu.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Voice playback volume is in register bits 0:2, not 4:6.
From: Mike Montour <mail@mmontour.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Werner Almesberger <werner@openmoko.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/juhl/trivial: (24 commits)
DOC: A couple corrections and clarifications in USB doc.
Generate a slightly more informative error msg for bad HZ
fix typo "is" -> "if" in Makefile
ext*: spelling fix prefered -> preferred
DOCUMENTATION: Use newer DEFINE_SPINLOCK macro in docs.
KEYS: Fix the comment to match the file name in rxrpc-type.h.
RAID: remove trailing space from printk line
DMA engine: typo fixes
Remove unused MAX_NODES_SHIFT
MAINTAINERS: Clarify access to OCFS2 development mailing list.
V4L: Storage class should be before const qualifier (sn9c102)
V4L: Storage class should be before const qualifier
sonypi: Storage class should be before const qualifier
intel_menlow: Storage class should be before const qualifier
DVB: Storage class should be before const qualifier
arm: Storage class should be before const qualifier
ALSA: Storage class should be before const qualifier
acpi: Storage class should be before const qualifier
firmware_sample_driver.c: fix coding style
MAINTAINERS: Add ati_remote2 driver
...
Fixed up trivial conflicts in firmware_sample_driver.c
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Add missing clk_enable()
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
two reasons:
1. GPIO namings and their mode definitions are conceptually not part
of the PXA register definitions
2. this is actually a temporary move in the transition of PXA2xx to
use MFP-alike APIs (as what PXA3xx is now doing), so that legacy
code will still work and new code can be added in step by step
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SoC audio driver for the Endrelia ETI_B1 board should not access
the PIO controller directly, but must rather use the AT91 GPIO
interface.
(This is updated version of patch with removed trailing whitespace)
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
snd_es1968_ac97_read() calls snd_es1968_ac97_wait() first outside a locked
area, and later, while holding a lock.
snd_es1968_ac97_wait() has a polling loop with a cond_resched() inside it..
which sleeps, so the second call is invalid.
This patch adds a version of the wait function that just pure polls. While
this is not very elegant in principle, it's very likely the easiest thing to
do here, we already checked if the chip was ready (while yielding) just
before, so it is very unlikely to take a long time here.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I accidentally removed the module license from sound/oss/ac97_codec.c in
commit 83bad1d764 ("scheduled OSS driver
removal")
Spotted by Roland <devzero@web.de>.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Please stop using random I2C driver IDs.
Also removed a pointless initialization to 0 of a static struct member.
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix the line-out volume control of eeepc p701 to be a proper slave of
the virtual master control.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Don't need to declare a struct when defining a structure layout. Both
of these structs are unused.
sound/pci/ice1712/revo.c:39:3: warning: symbol 'revo51' was not declared. Should it be static?
sound/pci/ice1712/phase.c:54:3: warning: symbol 'phase28' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add kcontrol argument to function since the API was changed by the commit
9af6d95624.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add kcontrol argument to functions since the API was changed by the commit
9af6d95624.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some models like eeepc ep20 have invalid mixer names that aren't
handled properly by virtual master controls. Rename them to the
proper names.
Also fixed some typos in the mixer names but they are not compiled
in right now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds a quirk to the Realtek ALC883 table for the Albatron KI690-AM2
motherboard to use the 6stack-dig model.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I forgot to set the module owner for the HiFier/Xonar models.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a wrong version check that would cause an invalid command to be sent
to SB 1.0 chips.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a workaround for the feedback pipe of E-Mu 0202/0404 USB devices
that reports the number of samples per packet instead of the number of
samples per microframe.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP dv8000 laptop has a problem with Master volume. It's due to the
connection of the widget 0x13. When it's connected from the analog
amp mixer (0x19), it works as expected mysteriously (ALSA bug#3775):
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3775
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Call free_irq() after iounmap() because other devices could trigger our
shared interrupt handler.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver gets Oops with ATI HDMI devices due to the wrong calculation
of index for playback streams. This patch fixes it. Reference:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3746
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warning:
WARNING: vmlinux.o(.text+0x11ec01a): Section mismatch in reference from the function setup_card() to the function .devinit.text:snd_usb_caiaq_control_init()
setup_card() are only used by init_card().
init_card() are only used by snd_probe()
snd_probe() are used for the .probe parameter in usb_driver.probe
Annotate them all __devinit to fix the warning.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pin widgets have always one amp-input value regardless of number of
connections. The proc file showed values wrongly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The capture source selection for ADC list with two elements is buggy
becaues of a wrong capture mux list. This patch fixes the starting
index based on spec->num_adc_nids.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The widget list of capture source selection for ALC883 contains the
wrong NIDs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't create vmaster controls if no slaves are found in the given list.
This prevents the error due to an empty vmaster control.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In linus' git tree I found this problem. Is it also in the alsa tree?
please confirm it's the right fix. The patch was not yet tested.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The GPIO pin 0 of the CM9780 must be set when muting the line input even
on non-Xonar cards.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixed the SPDIF output on Conexant Cx5045 codec. Added the missing
pin output setting and fixed the wrong NID for digital audio-out widget.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removed invalid __devinit and __devexit that are remaining after
split to a helper module.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver resubmits URBs from an error handler and schedules the error
handler from the URBs' completion handlers. To reliably kill the cycle
a flag must be used.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add proper ifdef's to the patch loading code moved from the old instr
layer so that opl3 driver can be compiled without the sequencer support.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sound drivers and the pnpbios core test for current->root != NULL. This
test seems to be unnecessary since we always have rootfs mounted before
initializing the drivers.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If count reaches zero, the loop ends, but the postfix decrement still
subtracts: testing for 'count == 0' will not work.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Reviewed-by: Ray Lee <ray-lk@madrabbit.org>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch contains the scheduled removal of OSS drivers whose config
options have been removed in 2.6.23.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After the APUS removal, some code can be removed.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sound/oss/sb_common.c: In function 'probe_sbmpu':
sound/oss/sb_common.c:1231: warning: cast to pointer from integer of different size
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace latency.c use with pm_qos_params use.
Signed-off-by: mark gross <mgross@linux.intel.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drivers that register a ->fault handler, but do not range-check the
offset argument, must set VM_DONTEXPAND in the vm_flags in order to
prevent an expanding mremap from overflowing the resource.
I've audited the tree and attempted to fix these problems (usually by
adding VM_DONTEXPAND where it is not obvious).
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some laptop has an internal analog microphone that is 'fixed'.
This patch prevents creating a 'Mic In as Output' switch for
ports that can't be outputs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This is based on pseudo-random playing around with the capabilities.
With ca0102 this card gives no output atall, ca0108 appears to work
fine, so it rather looks similar to the EMU1010b/EMU1010 changes.
Some other people seem to have succeeded in using this aswell:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3496
From: Veli-Matti Valtonen <maligor@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Don't create emu1010 kthread again at resume if it's already created.
Also make the thread function static.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The last change for emu1616 introduced a bug that the driver creates
emu1010-related controls even on non-emu boards. Fixed now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch improves E-Mu 1616(M) cardbus support. It adds definitions of the
new Microdock and 1010 cardbus registers (thanks again for descriptions
James) and improves mixer for this card. Now you can use S/PDIF and ADAT on
Mirodock and also use headpohone output on host cardbus card as another
independent output.
Signed-off-by: Ctirad Fertr <c.fertr@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
While the AK4396 and WM8785 datasheets say that the SPI clock cycle
length must be at least 200 ns, 320 ns seems not to work reliably with
the controller, so we better use 160 ns.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
With the Solo1 (es1938) I got a lot of xrun's during capture on my machine.
Tracing that down it seems to be comming from reading ocassionaly bad hw
pointers from the chip. This patch uses more checking to avoid that false
pointer reads.
Failed reads are giving back the last good value read instead of spinning in
a tight loop, which seems more appropriate to me in an interrupt. I think I
saw this trick used in another driver
Signed-off-by: Hermann Lauer <Hermann.Lauer@iwr.uni-heidelberg.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds support for Intel's SCH mobile chipset.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Support added for detecting HP jack presence via GPIO on several laptop docks.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the support for Dell T3400 with AD1984 codec chip.
ALSA bug#3699:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3699
Signed-off-by: Douglas Kosovic <douglask@itee.uq.edu.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add SPDIF playback switch to the slave element list so that it
can be toggled via the master control as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds the Intel ICH10 HD Audio Controller DeviceID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The PCM OSS emulation can cause Oops at sync operation due to the wrong
data size calculation. Typically happening on Sparc64:
http://lkml.org/lkml/2008/1/24/426
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the speaker-automute function to ALC262 HP models.
Also, 'Mono' mixer elements are renamed as more intuitive 'Speaker'.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Removed the PCM mixer elements conflicting with others.
Also renamed Master control to Headphone, which isn't a real master.
(The Master control is still created as a virtual master even after
this rename.)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The PCM mixer elements in HP T5735 model of ALC262 codec conflict
with Speaker and Headphone volumes. They should be removed.
Ditto for LineOut that is identical with Speaker.
Also, fixed/cleaned up the auto-mute callback to use the amp cache
correctly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Renamed the non-standard mixer elements 'iSpeaker' to 'Speaker'
in Realtek codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Julia Lawall