Avoid to define gpio_to_irq() and irq_to_gpio() for potential name
confliction since multiple architecture will be built together.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Parameters of GPIO_REG() should be assigned as volatile.
arch/arm/plat-pxa/include/plat/gpio.h: In function ‘gpio_get_value’:
arch/arm/plat-pxa/include/plat/gpio.h:12:21: error: invalid operands to
binary & (have ‘void *’ and ‘int’)
arch/arm/plat-pxa/include/plat/gpio.h: In function ‘gpio_set_value’:
arch/arm/plat-pxa/include/plat/gpio.h:21:4: error: lvalue required as
left operand of assignment
arch/arm/plat-pxa/include/plat/gpio.h:23:4: error: lvalue required as
left operand of assignment
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'next/devel2' of git://git.linaro.org/people/arnd/arm-soc: (30 commits)
ARM: mmp: register internal sram bank
ARM: mmp: register audio sram bank
ARM: mmp: add sram allocator
gpio/samsung: Complain loudly if we don't know the SoC
ARM: S3C64XX: Fix SoC identification for S3C64xx devices
ARM: S3C2443: Remove redundant s3c_register_clocks call for init_clocks
ARM: S3C24XX: Add devname for hsmmc1 pclk
ARM: S3C24XX: use clk_get_rate to init fclk in common_setup_clocks
ARM: S3C2443: Accommodate cpufreq frequency scheme in armdiv
ARM: S3C2443: handle unset armdiv values gracefully
ARM: S3C2443: Add get_rate operation for clk_armdiv
ARM: S3C2416: Add comment describing the armdiv/armclk
ARM: S3C2443: Move clk_arm and clk_armdiv to common code
ARM: S3C24XX: Add infrastructure to transmit armdiv to common code
ARM: S3C2416: Add armdiv_mask constant
ARM: EXYNOS4: Add support for M-5MOLS camera on Nuri board
ARM: EXYNOS4: Enable MFC on ORIGEN
ARM: SAMSUNG: Add support s3c2416-adc for S3C2416/S3C2450
ARM: SAMSUNG: Add support s3c2443-adc for S3C2443
ARM: SAMSUNG: Allow overriding of adc device name for S3C24XX
...
* 'next/fixes' of git://git.linaro.org/people/arnd/arm-soc: (28 commits)
ARM: pxa/cm-x300: properly set bt_reset pin
ARM: mmp: rename SHEEVAD to GPLUGD
ARM: imx: Fix typo 'MACH_MX31_3DS_MXC_NAND_USE_BBT'
ARM: i.MX28: shift frac value in _CLK_SET_RATE
plat-mxc: iomux-v3.h: implicitly enable pull-up/down when that's desired
ARM: mx5: fix clock usage for suspend
ARM: pxa: use correct __iomem annotations
ARM: pxa: sharpsl pm needs SPI
ARM: pxa: centro and treo680 need palm27x
ARM: pxa: make pxafb_smart_*() empty when not enabled
ARM: pxa: select POWER_SUPPLY on raumfeld
ARM: pxa: pxa95x is incompatible with earlier pxa
ARM: pxa: CPU_FREQ_TABLE is needed for CPU_FREQ
ARM: pxa: pxa95x/saarb depends on pxa3xx code
ARM: pxa: allow selecting just one of TREO680/CENTRO
ARM: pxa: export symbols from pxa3xx-ulpi
ARM: pxa: make zylonite_pxa*_init declaration match code
ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available
ARM: at91: add defconfig for at91sam9g45 family
ARM: at91: remove dependency for Atmel PWM driver selector in Kconfig
...
MMP2 have the internal sram, this sram can be allocated
for video, power management and secure processor.
Now the sram usage is:
0xd1000000 ~ 0xd101ffff (128KB) : reserved for secure processor
0xd1020000 ~ 0xd1037fff (96KB) : for video and PM
Register the internal sram's second half 96KB buffer,
so that video and PM can dynamically alloc/free from it.
Signed-off-by: Leo Yan <leoy@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
MMP platform has sram for the audio island;
Add the device structure for the audio sram,
and register the audio sram device at init phase.
Signed-off-by: Leo Yan <leoy@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
On mmp platform, there have two sram banks:
audio sram and internal sram. The audio sram is mainly for audio;
the internal sram is for video, wtm and power management.
So add the sram allocator using genalloc to manage them.
Every sram bank will register its own platform device
info, after the sram allocator create the generic pool
for the sram bank, the user module can use the pool's
name to get the pool handler; then it can use the handler
to alloc/free memory with genalloc APIs.
Signed-off-by: Leo Yan <leoy@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This tries to clear up the confusion between integers and iomem pointers
in the marvell pxa platform. MMIO addresses are supposed to be __iomem*
values, in order to let the Linux type checking work correctly. This
patch moves the cast to __iomem as far back as possible, to the place
where the MMIO virtual address windows are defined.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some platforms (like OMAP not to name it) are doing rather complicated
hacks just to determine the base UART address to use. Let's give their
addruart macro some slack by providing an extra work register which will
allow for much needed cleanups.
This is basically a no-op as this commit is only adding the extra argument
to the macro but no one is using it yet.
Signed-off-by: nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Move definitions from mfp-gplugd.h to mfp-pxa168.h as they aren't
gplugD specific.
Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
As suggested by Arnd, move platform data to include/linux/platform_data
in order to improve build coverage for the driver.
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Now most of ARM machines has the alsmot same __clk_get/put() macro
So place it at the arch/arm/include/asm/clkdev.h and remove the reduntant header files
But some machines don't have the same form as above. It can use the machince specific clkdev file by HAVE_MACH_CLKDEV config
Now there are only 3 caese.
1) define the clk structure with clkdev macro => Need to move clk structure to proper header file
arch/arm/mach-versatile/include/mach/clkdev.h
arch/arm/mach-realview/include/mach/clkdev.h
arch/arm/mach-vexpress/include/mach/clkdev.h
arch/arm/mach-integrator/include/mach/clkdev.h
2) export the __clk_get/put function at clock.c
arch/arm/mach-shmobile/include/mach/clkdev.h
3) demuxing the clk source
arch/arm/mach-u300/include/mach/clkdev.h
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
PXA168 has 3 onchip UARTs. Added support for the third one
Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
To be able to relocate the .bss section at run time independently from
the rest of the code, we must make sure that no GOTOFF relocations are
used with .bss symbols. This usually means that no global variables can
be marked static unless they're also const.
Let's remove the static qualifier from current offenders, or turn them
into const variables when possible. Next commit will ensure the build
fails if one of those is reintroduced due to otherwise enforced coding
standards for the kernel.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Avoid to mismatch between NR_BUILTIN_GPIO and gpio interrupt number.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch moves the platform data definition from
arch/arm/plat-pxa/include/plat/i2c.h to include/linux/i2c/pxa-i2c.h so
it can be accessed from x86 the same way as on ARM.
This change should make no functional change to the PXA code. The move
is verified by building the following defconfigs:
cm_x2xx_defconfig corgi_defconfig em_x270_defconfig ezx_defconfig
imote2_defconfig pxa3xx_defconfig spitz_defconfig zeus_defconfig
raumfeld_defconfig magician_defconfig mmp2_defconfig pxa168_defconfig
pxa910_defconfig
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This uncouple PHYS_OFFSET from the platform definitions, thereby
facilitating run-time computation of the physical memory offset.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Drive strength for PXA910 is a 2 bit value but because of the mapping in
plat-pxa/mfp.h needs to be shifted up one bit to handle real
location in mfp registers. (MMP2 and PXA910 drive strength start
at bit 11 while PXA168 starts at bit 10).
Values 0, 1, 2, and 3 effectively need to be
0, 2, 4, and 6 to fit into register. 8 does not work.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Drive strength for MMP2 is a 2 bit value but because of the mapping in
plat-pxa/mfp.h needs to be shifted up one bit to handle real
location in mfp registers. (MMP2 and PXA910 drive strength start
at bit 11 while PXA168 starts at bit 10).
Values 0, 1, 2, and 3 effectively need to be
0, 2, 4, and 6 to fit into register. 8 does not work.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: John Watlington <wad@laptop.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Added board defintion, header, and debug UART support.
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Reset vector for pxa168 is 0xffff_0000 not 0x0. This fix allows
reboot to work
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Sync twsi index to register index. It's used to avoid typo error.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
In MMP2, clock tick rate should be 6500000.
Signed-off-by: Mingliang Hu <mhu4@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
In mmp2, 6 banks of GPIO registers are supported. So we can support 192
GPIO pins at most.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Support ssp devices in PXA168. PXA168 could reuse the code of PXA SSP.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Due to commit:
5de813b ARM: Eliminate decompressor -Dstatic= PIC hack
The data section will be discarded for the decompressor, thus move the
static variables into BSS section by initializing them at run time.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Marvell MMP2 (aka ARMADA610) is a SoC based on PJ4 core. It's
ARMv6 compatible. Support basic interrupt handler and timer,
and basic support for MMP2 based FLINT platform.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Makes it consistent with VMALLOC_START
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
"""The Marvell® PXA168 processor is the first in a family of application
processors targeted at mass market opportunities in computing and consumer
devices. It balances high computing and multimedia performance with low
power consumption to support extended battery life, and includes a wealth
of integrated peripherals to reduce overall BOM cost .... """
See http://www.marvell.com/featured/pxa168.jsp for more information.
1. Marvell Mohawk core is a hybrid of xscale3 and its own ARM core,
there are many enhancements like instructions for flushing the
whole D-cache, and so on
2. Clock reuses Russell's common clkdev, and added the basic support
for UART1/2.
3. Devices are a bit different from the 'mach-pxa' way, the platform
devices are now dynamically allocated only when necessary (i.e.
when pxa_register_device() is called). Description for each device
are stored in an array of 'struct pxa_device_desc'. Now that:
a. this array of device description is marked with __initdata and
can be freed up system is fully up
b. which means board code has to add all needed devices early in
his initializing function
c. platform specific data can now be marked as __initdata since
they are allocated and copied by platform_device_add_data()
4. only the basic UART1/2/3 are added, more devices will come later.
Signed-off-by: Jason Chagas <chagas@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Haojian Zhuang