dev_priv is what the macro works hard to extract, pass it directly.
> sed 's/\([A-Z].*(dev_priv\)->dev)/\1)/g'
v2:
- Include all wrapper macros too (Chris)
v3:
- Include sed cmdline (Chris)
v4:
- Break long line
- Rebase
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460016485-8089-1-git-send-email-joonas.lahtinen@linux.intel.com
Due to timing issues in the HW, some of the status bits required for GuC
authentication occasionally don't get set; when that happens, the GuC
cannot be initialized and we will be left with a wedged GPU. The W/A
suggested is to perform a soft reset of the GuC and attempt to reload
the F/W again for few times before giving up.
As the failure is dependent on timing, tests performed by triggering
manual full gpu reset (i915_wedged) showed that we could sometimes hit
this after several thousand iterations, but sometimes tests ran even
longer without any issues. Reset and reload mechanism proved helpful
when we indeed hit f/w load failure, so it is better to include this
to improve driver stability.
This change implements the following WAs,
WaEnableuKernelHeaderValidFix:skl,bxt
WaEnableGuCBootHashCheckNotSet:skl,bxt
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
__force_wake_get() only acquires a temporary wakeref on forcewake that is
automatically released when a timer expires. When reading the code
again, I confused __intel_uncore_forcewake_get() for __force_wake_get()
and to my shame thought I found a bug in unbalanced wake_count handling.
I claim that if the function had been called __force_wake_auto() instead
I would not have embarrassed myself.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458829907-26596-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
In full gpu reset we prime all engines and reset domains corresponding to
each engine. Per engine reset is just a special case of this process
wherein only a single engine is reset. This change is aimed to modify
relevant functions to achieve this. There are some other steps we carry out
in case of engine reset which are addressed in later patches.
Reset func now accepts a mask of all engines that need to be reset. Where
per engine resets are supported, error handler populates the mask
accordingly otherwise all engines are specified.
v2: ALL_ENGINES mask fixup, better for_each_ring_masked (Chris)
v3: Whitespace fixes (Chris)
v4: Rebase due to s/ring/engine
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458143640-20563-1-git-send-email-mika.kuoppala@intel.com
Some trivial ones, first pass done with Coccinelle:
@@
@@
(
- I915_NUM_RINGS
+ I915_NUM_ENGINES
|
- intel_ring_flag
+ intel_engine_flag
|
- for_each_ring
+ for_each_engine
|
- i915_gem_request_get_ring
+ i915_gem_request_get_engine
|
- intel_ring_idle
+ intel_engine_idle
|
- i915_gem_reset_ring_status
+ i915_gem_reset_engine_status
|
- i915_gem_reset_ring_cleanup
+ i915_gem_reset_engine_cleanup
|
- init_ring_lists
+ init_engine_lists
)
But that didn't fully work so I cleaned it up with:
for f in *.[hc]; do sed -i -e s/I915_NUM_RINGS/I915_NUM_ENGINES/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_request_get_ring/i915_gem_request_get_engine/ $f; done
for f in *.[hc]; do sed -i -e s/intel_ring_flag/intel_engine_flag/ $f; done
for f in *.[hc]; do sed -i -e s/intel_ring_idle/intel_engine_idle/ $f; done
for f in *.[hc]; do sed -i -e s/init_ring_lists/init_engine_lists/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_reset_ring_cleanup/i915_gem_reset_engine_cleanup/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_reset_ring_status/i915_gem_reset_engine_status/ $f; done
v2: Rebase.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
GPU engine reset handshaking is something that is applicable to both full GPU
reset and engine reset, which is something that is part of the upcoming TDR
per-engine hang recovery patches. Break out the common engine reset
request/unrequest code (originally written by Mika Kuoppala) for reuse later
in the TDR enablement patch series.
v2: correct indentation and drop unused returned value (Mika)
v3: We have forcewake during reset so use *_FW reg access (Mika)
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
[Mika: Fixed format warning]
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456929984-16323-1-git-send-email-mika.kuoppala@intel.com
RC6 setup is shared between BIOS and Driver. BIOS sets up subset of RC6
setup registers. If those are not setup Driver should not enable RC6.
For implementing this, driver can check RC_CTRL0 and RC_CTRL1 values
to know if BIOS has enabled HW/SW RC6.
This will also enable user to control RC6 using BIOS settings alone.
RC6 related instability can be avoided by disabling via BIOS settings
till driver fixes it.
v2: Had placed logic in gen8 function by mistake. Fixed it.
Ensuring RPM is not enabled in case BIOS disabled RC6.
v3: Need to disable RPM if RC6 is disabled due to BIOS settings. (Daniel)
Runtime PM enabling happens before gen9_enable_rc6.
Moved the updation of enable_rc6 parameter in intel_uncore_sanitize.
v4: Added elaborate check for BIOS RC6 setup. Prepared check_pctx for bxt.
(Imre)
v5: Caching reserved stolen base and size in the driver private data.
Reorganized RC6 setup check. Moved from gen9_enable_rc6 to
intel_uncore_sanitize. (Imre)
v6: Rebasing on the patch submitted by Imre that moves gem_init_stolen
earlier in the load.
v7: Removed PWRCTX_MAXCNT_VCSUNIT1 check as it applies to SKL. (Imre)
v8: Fixed formatting and checkpatch issues. Fixed functional issue where
RC6 ctx size check was missing. (Imre)
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454697809-22113-1-git-send-email-sagar.a.kamble@intel.com
The capability to detect unclaimed register access was
recently introduced for vlv/chv platforms. Apparently
there are plenty of unclaimed access on these platforms,
resulting in new dmesg warns. But as we are trying to form
a beachhead for CI/Bat, all new warns are adding to the
noise and thus not desirable at this point in time.
Make it so that if in these platforms the automatic arming
was responsible for mmio_debug enabling, ignore the warns.
If user/dev wants to fix these, he can still do so by
i915.mmio_debug=1234.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1453285943-24614-1-git-send-email-mika.kuoppala@intel.com
If we go into suspend with unclaimed access detected,
it would be nice to catch that access on a next suspend path.
So instead of just notifying about it, arm the unclaimed
mmio checks on suspend side.
We want to keep the asymmetry on resume, as if it was
on resume path, it was not driver that is responsible so
no point in arming mmio debugs.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1452261080-6979-2-git-send-email-mika.kuoppala@intel.com
With commit 8ac3e1bb76 ("drm/i915: Add non claimed mmio checking
for vlv/chv") we now have chv/vlv support in place for detecting
unclaimed access. Also the perf hit of extra mmio read
is now only suffered if mmio_debug is set.
This allows us to stuff the macro for unclaimed reg
detection inside a generic gen6 register access, as now all
gens using these macros uses also unclaimed debugs, the one
exception being snb. We gain more clean and generic macros
and only downside is that snb will suffer one branch perf hit
without upside.
Note that the hsw write path debug register check now
happens before fifo check, but this should not make
any real difference.
As vlv/chv use the generic gen6 access macros, the consequence
is that they gain the mmio_debug feature.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1452261080-6979-1-git-send-email-mika.kuoppala@intel.com
Imre mentioned that chv might also have capability to
track unclaimed mmio accesses. Ville added that
both chv and vlv has this capability and he had already
made this way back [1]. Mimic what Ville's patch does
but adapt on top of less frequent mmio accesses by
omitting checking always on reg writes.
This patch is untested as of now.
v2: overflow handling and posting omitted (Ville)
References: [1] http://lists.freedesktop.org/archives/intel-gfx/2013-May/027599.html
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450201542-22918-1-git-send-email-mika.kuoppala@intel.com
Remove char* assignments and add branching hint and
also constify the parameters.
This results in a 35 bytes shorter fast path, so author
boldly assumes it helps without doing in-depth assembly
analysis.
v2: use WARN's branching (Chris), commit name (Joonas)
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450189512-30360-5-git-send-email-mika.kuoppala@intel.com
We have done unclaimed register access check in normal
(mmio_debug=0) mode once per write. This adds probability
of finding the exact sequence where we did the bad access, but
also adds burden to each write.
As we have mmio_debug available for more fine grained analysis,
give up accuracy of detecting correct spot at the first occurrence
by doing the one shot detection and arming of mmio_debug in hangcheck
and in modeset. This removes the write path performance burden.
v2: Remove gratuitous DRM_DEBUG and return value, comments (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450250808-14864-1-git-send-email-mika.kuoppala@intel.com
Currently interrupt code is the only place checking
for the unclaimed register access prior to actual register
macros using the same functionality. Rename the function
and make it return bool so that the possible error message
context is clear in the caller side. The motivation is to allow
usage of unclaimed detection on arbitrary places.
v2: rebase, s/access/mmio, s/dev/dev_priv
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450189512-30360-2-git-send-email-mika.kuoppala@intel.com
Access the unclaimed reg detection register through
one helper which also does cleanup. Note that we now access
the register only if the platform has the actual non claimed
access bit. This prevents reading the register with gens that
doesn't have the register or the unclaimed bit,
when debug_mmio > 0.
Note that we post after clearing the bit. This makes sure
that the next unclaimed write access would get detected
also if it happened right after clearing, and not fold
into the previous detection.
v2: s/unclaimed_reg_access/check_for_unclaimed_mmio (Chris)
debug log on unclaimed detection on uncore init (Joonas)
v3: remove posting read (Ville)
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450200287-24080-1-git-send-email-mika.kuoppala@intel.com
As a preparation for follow-up patches add a new helper that checks
whether we hold an RPM reference, since this is what we want most of
the cases. Atm this helper will only check for the HW suspended state, a
follow-up patch will do the actual change to check the refcount instead.
One exception is the forcewake release timer function, where it's
guaranteed that the HW is on even though the RPM refcount drops to zero.
This guarantee is provided by flushing the timer in the runtime suspend
handler. So leave the assert_device_not_suspended check in place there.
Also rename assert_device_suspended for consistency and export these
helpers as a preparation for the follow-up patches.
No functional change.
v3:
- change the assert warning message to be more meaningful (Chris)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-6-git-send-email-imre.deak@intel.com
We don't really need to check this flag in the get/put/assert helpers,
as on platforms without RPM support we won't ever enable RPM. That means
pm.suspend will be always false and the assert will be always true.
Do this to simplify the code and to let us extend the RPM asserts to all
platforms for a better coverage.
Motivated by Ville.
v2-v3:
- unchanged
v4:
- remove the HAS_RUNTIME_PM check from intel_runtime_pm_enable() too
made possible by the previous two patches
v5:
- rebased on the previous new patch in the series that keeps
HAS_RUNTIME_PM() in intel_runtime_pm_enable() with a permanent
reference taken there
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450352931-16498-1-git-send-email-imre.deak@intel.com
The cherryview device shares many characteristics with the valleyview
device. When support was added to the driver for cherryview, the
corresponding device info structure included .is_valleyview = 1.
This is not correct and leads to some confusion.
This patch changes .is_valleyview to .is_cherryview in the cherryview
device info structure and simplifies the IS_CHERRYVIEW macro.
Then where appropriate, instances of IS_VALLEYVIEW are replaced with
IS_VALLEYVIEW || IS_CHERRYVIEW or equivalent.
v2: Use IS_VALLEYVIEW || IS_CHERRYVIEW instead of defining a new macro.
Also add followup patches to fix issues discovered during the first
review. (Ville)
v3: Fix some style issues and one gen check. Remove CRT related changes
as CRT is not supported on CHV. (Imre, Ville)
v4: Make a few more optimizations. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Wayne Boyer <wayne.boyer@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449692975-14803-1-git-send-email-wayne.boyer@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWUmHZAAoJEHm+PkMAQRiGHtcH/RVRsn8re0WdRWYaTr9+Hknm
CGlRJN4LKecttgYQ/2bS1QsDbt8usDPBiiYVopqGXQxPBmjyDAqPjsa+8VzCaVc6
WA+9LDB+PcW28lD6BO+qSZCOAm7hHSZq7dtw9x658IqO+mI2mVeCybsAyunw2iWi
Kf5q90wq6tIBXuT8YH9MXGrSCQw00NclbYeYwB9CmCt9hT/koEFBdl7uFUFitB+Q
GSPTz5fXhgc5Lms85n7flZlrVKoQKmtDQe4/DvKZm+SjsATHU9ru89OxDBdS5gSG
YcEIM4zc9tMjhs3GC9t6WXf6iFOdctum8HOhUoIN/+LVfeOMRRwAhRVqtGJ//Xw=
=DCUg
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rc2' into drm-intel-next-queued
Linux 4.4-rc2
Backmerge to get at
commit 1b0e3a049e
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Nov 5 23:04:11 2015 +0200
drm/i915/skl: disable display side power well support for now
so that we can proplery re-eanble skl power wells in -next.
Conflicts are just adjacent lines changed, except for intel_fbdev.c
where we need to interleave the changs. Nothing nefarious.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Make I915_READ and I915_WRITE more type safe by wrapping the register
offset in a struct. This should eliminate most of the fumbles we've had
with misplaced parens.
This only takes care of normal mmio registers. We could extend the idea
to other register types and define each with its own struct. That way
you wouldn't be able to accidentally pass the wrong thing to a specific
register access function.
The gpio_reg setup is probably the ugliest thing left. But I figure I'd
just leave it for now, and wait for some divine inspiration to strike
before making it nice.
As for the generated code, it's actually a bit better sometimes. Eg.
looking at i915_irq_handler(), we can see the following change:
lea 0x70024(%rdx,%rax,1),%r9d
mov $0x1,%edx
- movslq %r9d,%r9
- mov %r9,%rsi
- mov %r9,-0x58(%rbp)
- callq *0xd8(%rbx)
+ mov %r9d,%esi
+ mov %r9d,-0x48(%rbp)
callq *0xd8(%rbx)
So previously gcc thought the register offset might be signed and
decided to sign extend it, just in case. The rest appears to be
mostly just minor shuffling of instructions.
v2: i915_mmio_reg_{offset,equal,valid}() helpers added
s/_REG/_MMIO/ in the register defines
mo more switch statements left to worry about
ring_emit stuff got sorted in a prep patch
cmd parser, lrc context and w/a batch buildup also in prep patch
vgpu stuff cleaned up and moved to a prep patch
all other unrelated changes split out
v3: Rebased due to BXT DSI/BLC, MOCS, etc.
v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com
Add 'u32 offset' to the uncore register access functions. For now
it's the same as 'reg', but once type safety gets added 'reg' will be
the type safe register variable and 'offset' the raw offset.
v2: s/uint32_t/u32/ (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446839236-20035-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
I need to add a new variable into GEN6_{READ,WRITE}_HEADER, but the vgpu
won't need it, so let's avoid an unused variable warning by splitting
the vgpu stuff to use its own macros.
Cc: Eddie Dong <eddie.dong@intel.com>
Cc: Jike Song <jike.song@intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Cc: Yu Zhang <yu.c.zhang@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Cc: Zhiyuan Lv <zhiyuan.lv@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-26-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Zhiyuan Lv <zhiyuan.lv@intel.com>
Store the upper dword of the register offset in the whitelist as well.
This would allow it to read register where the two halves aren't sitting
right next to each other, and it'll make it easier to make register
access type safe.
While at it change the register offsets to u32 from u64. Our register
space isn't quite that big, yet :)
v2: Use ldw/udw as the suffixes, and add a note about
64bit wide split regs (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446839021-18599-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
We have a timed release of a forcewake when using
I915_READ/WRITE macros. wait_for() macro will go to quite
long sleep if the first read doesn't satisfy the condition for
successful exit. With these two interacting, it is possible that
we lose the forcewake during the wait_for() and the subsequent read
will reaquire forcewake.
Further experiments with skl shows that when we lose forcewake,
we lose the reset request we submitted. So reset request register
is not power context saved.
Grab forcewakes for all engines before starting the reset/request
dance so that all requests stay valid for the duration of reset
requisition across all the engines.
v2: Add comment on power well sleeps. Wrap the reset handling
under forcewake instead of just reset requests (Chris)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92774
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Tomi Sarvela <tomix.p.sarvela@intel.com> (v1, v2)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446721898-1450-1-git-send-email-mika.kuoppala@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Include an early NEEDS_FORCEWAKE() check for vlv and chv.
Hopefully that will avoid doing so many range checks in for many
register accesses (at least for all display registers).
Note that vlv already had the check in the write path since it shares
the gen6+ code for that.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445517300-28173-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Change the fw domain handling in the vlv/chv register read/write
functions to look more like the SKL code, ie. have a single
__force_wake_get() get call instead of multiple ones.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445517300-28173-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Change FORCEWAKE & co. reads for the error state to use I915_READ_FW().
Reading a FORCEWAKE register using a function that can frob forcewake
just seems wrong.
There is a check to skip grabbing the forcewake for accessing FORCEWAKE
in intel_uncore.c, but there's no such check for FORCEWAKE_MT. So no
idea what is currently happening with FORCEWAKE_MT reads. FORCEWAKE_VLV
is fortunately outside the forcewake range anyway, so no actual issue
with that one.
So let's just make the rule that you can't access FORCEWAKE registers with
the normal I915_READ() stuff, and we can drop the extra FORCEWAKE check
from NEEDS_FORCEWAKE(). While at it use NEEDS_FORCEWAKE() on BDW, where
it was skipped for whatever bikeshed reason that I've already forgotten.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445517300-28173-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
There's no need for __raw_i915_read8() & co. to be macros, so make them
inline functions. To avoid typo mistakes generate the inline functions
using preprocessor templates.
We have a few users of the raw register acces functions outside
intel_uncore.c, so let's also move the functions into intel_drv.h.
While doing that switch I915_READ_FW() & co. to use the
__raw_i915_read() functions, and use the _FW macros everywhere
outside intel_uncore.c where we want to read registers without
grabbing forcewake and whatnot. The only exception is
i915_check_vgpu() which itself gets called from intel_uncore.c,
so using the __raw_i915_read stuff there seems appropriate.
v2: Squash in the intel_uncore.c->i915_drv.h move
Convert I915_READ_FW() to use __raw_i915_read(), and use
I915_READ_FW() outside of intel_uncore.c (Chris)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445517300-28173-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On BXT, We Observe timeout for forcewake request completion with 2ms polling period as given here:
[drm:fw_domains_get] ERROR render: timed out waiting for forcewake ack request.
Polling for 50ms is recommended to avoid these timeouts.
Change-Id: Ie715b0069a3049606e9602bc5e97a6511890864d
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unless future specs tells otherwise we can assume future gens
inherit some stuff from the previous so let's handle
missed cases when we know tehy should't be there and assume
default equals newest one.
No functional changes.
v2: Remove useless case as pointed out by Ville.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dear git bisect user,
Even though this is the patch that introduced the WARN() you're
bisecting, please notice that it's very likely that the problem you're
facing was already present before this commit. In other words: this
commit adds code to detect errors and give WARN()s about them, but the
errors were already there.
In order to continue your debug, please use the i915.mmio_debug
option, check the backtraces and try to discover which read or write
operation is causing the error message. Then check if this is
happening because the register does not exist or because its power
well is down when the operation is being done.
On my SKL machine, if I use i915.mmio_debug=999, this patch triggers
42 WARNs just by booting. I didn't investigate them yet. Normal users
are only going to get a single WARN due to the default i915.mmio_debug
setting.
Thank you for your comprehension,
Paulo
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A couple of hand rolled ARRAY_SIZE()s caught my eye. Get rid of them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-intel-fixes because a bunch of atomic patch backporting
we had to do lead to horrible conflicts.
Conflicts:
drivers/gpu/drm/drm_crtc.c
Just a bit of context conflict between -next and -fixes.
drivers/gpu/drm/i915/intel_atomic.c
drivers/gpu/drm/i915/intel_display.c
Atomic conflicts, always pick the code from -next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Since the hardware sometimes mysteriously totally flummoxes the 64bit
read of a 64bit register when read using a single instruction, split the
read into two instructions. Since the read here is of automatically
incrementing timestamp counters, we also have to be very careful in
order to make sure that it does not increment between the two
instructions.
However, since userspace tried to workaround this issue and so enshrined
this ABI for a broken hardware read and in the process neglected that
the read only fails in some environments, we have to introduce a new
uABI flag for userspace to request the 2x32 bit accurate read of the
timestamp.
v2: Fix alignment check and include details of the workaround for
userspace.
Reported-by: Karol Herbst <freedesktop@karolherbst.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91317
Testcase: igt/gem_reg_read
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: stable@vger.kernel.org
Tested-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the user disables the GPU reset using the i915.reset parameter and
one occurs, report that we failed to reset the GPU. If we return early,
as we currently do, then we leave all state intact (with a hung GPU)
and clients block forever waiting for their requests to complete.
Testcase: igt/gem_eio
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Mark i915.reset as an unsafe modoption, as discussed with
Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order for gen8+ hardware to guarantee that no context switch
takes place during engine reset and that current context is properly
saved, the driver needs to notify and query hw before commencing
with reset.
There are gpu hangs where the engine gets so stuck that it never will
report to be ready for reset. We could proceed with reset anyway, but
with some hangs with skl, the forced gpu reset will result in a system
hang. By inspecting the unreadiness for reset seems to correlate with
the probable system hang.
We will only proceed with reset if all engines report that they
are ready for reset. If root cause for system hang is found and
can be worked around with another means, we can reconsider if
we can reinstate full reset for unreadiness case.
v2: -EIO, Recovery, gen8 (Chris, Tomas, Daniel)
v3: updated commit msg
v4: timeout_ms, simpler error path (Chris)
References: https://bugs.freedesktop.org/show_bug.cgi?id=89959
References: https://bugs.freedesktop.org/show_bug.cgi?id=90854
Testcase: igt/gem_concurrent_blit/prw-blt-overwrite-source-read-rcs-forked
Testcase: igt/gem_concurrent_blit/gtt-blt-overwrite-source-read-rcs-forked
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tomas Elf <tomas.elf@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In igt, we want to test handling of GPU hangs, both for recovery
purposes and for reporting. However, we don't want to inject a genuine
GPU hang onto a machine that cannot recover and so be permenantly
wedged. Rather than embed heuristics into igt, have the kernel report
exactly when it expects the GPU reset to work.
This can also be usefully extended in future to indicate different
levels of fine-grained resets.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tim Gore <tim.gore@intel.com>
Cc: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2015-04-23:
- dither support for ns2501 dvo (Thomas Richter)
- some polish for the gtt code and fixes to finally enable the cmd parser on hsw
- first pile of bxt stage 1 enabling (too many different people to list ...)
- more psr fixes from Rodrigo
- skl rotation support from Chandra
- more atomic work from Ander and Matt
- pile of cleanups and micro-ops for execlist from Chris
drm-intel-next-2015-04-10:
- cdclk handling cleanup and fixes from Ville
- more prep patches for olr removal from John Harrison
- gmbus pin naming rework from Jani (prep for bxt)
- remove ->new_config from Ander (more atomic conversion work)
- rps (boost) tuning and unification with byt/bsw from Chris
- cmd parser batch bool tuning from Chris
- gen8 dynamic pte allocation (Michel Thierry, based on work from Ben Widawsky)
- execlist tuning (not yet all of it) from Chris
- add drm_plane_from_index (Chandra)
- various small things all over
* tag 'drm-intel-next-2015-04-23-fixed' of git://anongit.freedesktop.org/drm-intel: (204 commits)
drm/i915/gtt: Allocate va range only if vma is not bound
drm/i915: Enable cmd parser to do secure batch promotion for aliasing ppgtt
drm/i915: fix intel_prepare_ddi
drm/i915: factor out ddi_get_encoder_port
drm/i915/hdmi: check port in ibx_infoframe_enabled
drm/i915/hdmi: fix vlv infoframe port check
drm/i915: Silence compiler warning in dvo
drm/i915: Update DRIVER_DATE to 20150423
drm/i915: Enable dithering on NatSemi DVO2501 for Fujitsu S6010
rm/i915: Move i915_get_ggtt_vma_pages into ggtt_bind_vma
drm/i915: Don't try to outsmart gcc in i915_gem_gtt.c
drm/i915: Unduplicate i915_ggtt_unbind/bind_vma
drm/i915: Move ppgtt_bind/unbind around
drm/i915: move i915_gem_restore_gtt_mappings around
drm/i915: Fix up the vma aliasing ppgtt binding
drm/i915: Remove misleading comment around bind_to_vm
drm/i915: Don't use atomics for pg_dirty_rings
drm/i915: Don't look at pg_dirty_rings for aliasing ppgtt
drm/i915/skl: Support Y tiling in MMIO flips
drm/i915: Fixup kerneldoc for struct intel_context
...
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
This WA is avoid problem between shadow vs wake FIFO unload
problem during CPD/RC6 transactions on CHV.
v2: Define individual bits GTFIFOCTL (Ville)
v3: move WA to uncore_early_sanitize (ville)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Jani: fixed some whitespace issues while applying]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This eliminates six needless spin lock/unlock pairs when writing out
ELSP.
v2: Respin with my preferred colour.
v3: Mostly back to the original colour
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> [v1]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we have a single unclaimed register, we will have lots. A WARN for
each one makes the machine unusable and does not aid debugging. Convert
the i915.mmio_debug option to a counter for how many WARNs to fire
before shutting up. Even when i915.mmio_debug was disabled it would
continue to shout an *ERROR* for every interrupt, without any
information at all for debugging.
The massive verbiage was added in
commit 5978118c39
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Wed Jul 16 17:49:29 2014 -0300
drm/i915: reorganize the unclaimed register detection code
v2: Automatically enable invalid mmio reporting for the *next* invalid
access if mmio_debug is disabled by default. This should give us clearer
debug information without polluting the logs too much.
v3: Compile fixes, rebase.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Update modparam text per the thread.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 05a2fb157e ("drm/i915: Consolidate forcewake code")
failed to take into account that we have used to reset both
the gen6 style and the multithreaded style forcewake registers.
This is due to fact that ivb can use either, depending on how the
bios has set up the machine.
Mimic the old semantics before we have determined the correct variety
and reset both before the ecobus probe.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Huang Ying <ying.huang@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Y tiling support for scanout from Tvrtko&Damien
- Remove more UMS support
- some small prep patches for OLR removal from John Harrison
- first few patches for dynamic pagetable allocation from Ben Widawsky, rebased
by tons of other people
- DRRS support patches (Sonika&Vandana)
- fbc patches from Paulo
- make sure our vblank callbacks aren't called when the pipes are off
- various patches all over
* tag 'drm-intel-next-2015-02-27' of git://anongit.freedesktop.org/drm-intel: (61 commits)
drm/i915: Update DRIVER_DATE to 20150227
drm/i915: Clarify obj->map_and_fenceable
drm/i915/skl: Allow Y (and Yf) frame buffer creation
drm/i915/skl: Update watermarks for Y tiling
drm/i915/skl: Updated watermark programming
drm/i915/skl: Adjust get_plane_config() to support Yb/Yf tiling
drm/i915/skl: Teach pin_and_fence_fb_obj() about Y tiling constraints
drm/i915/skl: Adjust intel_fb_align_height() for Yb/Yf tiling
drm/i915/skl: Allow scanning out Y and Yf fbs
drm/i915/skl: Add new displayable tiling formats
drm/i915: Remove DRIVER_MODESET checks from modeset code
drm/i915: Remove regfile code&data for UMS suspend/resume
drm/i915: Remove DRIVER_MODESET checks from gem code
drm/i915: Remove DRIVER_MODESET checks in the gpu reset code
drm/i915: Remove DRIVER_MODESET checks from suspend/resume code
drm/i915: Remove DRIVER_MODESET checks in load/unload/close code
drm/i915: fix a printk format
drm/i915: Add media rc6 residency file to sysfs
drm/i915: Add missing description to parameter in alloc_pt_range
drm/i915: Removed the read of RP_STATE_CAP from sysfs/debugfs functions
...
- use the atomic helpers for plane_upate/disable hooks (Matt Roper)
- refactor the initial plane config code (Damien)
- ppgtt prep patches for dynamic pagetable alloc (Ben Widawsky, reworked and
rebased by a lot of other people)
- framebuffer modifier support from Tvrtko Ursulin, drm core code from Rob Clark
- piles of workaround patches for skl from Damien and Nick Hoath
- vGPU support for xengt on the client side (Yu Zhang)
- and the usual smaller things all over
* tag 'drm-intel-next-2015-02-14' of git://anongit.freedesktop.org/drm-intel: (88 commits)
drm/i915: Update DRIVER_DATE to 20150214
drm/i915: Remove references to previously removed UMS config option
drm/i915/skl: Use a LRI for WaDisableDgMirrorFixInHalfSliceChicken5
drm/i915/skl: Fix always true comparison in a revision id check
drm/i915/skl: Implement WaEnableLbsSlaRetryTimerDecrement
drm/i915/skl: Implement WaSetDisablePixMaskCammingAndRhwoInCommonSliceChicken
drm/i915: Add process identifier to requests
drm/i915/skl: Implement WaBarrierPerformanceFixDisable
drm/i915/skl: Implement WaCcsTlbPrefetchDisable:skl
drm/i915/skl: Implement WaDisableChickenBitTSGBarrierAckForFFSliceCS
drm/i915/skl: Implement WaDisableHDCInvalidation
drm/i915/skl: Implement WaDisableLSQCROPERFforOCL
drm/i915/skl: Implement WaDisablePartialResolveInVc
drm/i915/skl: Introduce a SKL specific init_workarounds()
drm/i915/skl: Document that we implement WaRsClearFWBitsAtReset
drm/i915/skl: Implement WaSetGAPSunitClckGateDisable
drm/i915/skl: Make the init clock gating function skylake specific
drm/i915/skl: Provide a gen9 specific init_render_ring()
drm/i915/skl: Document the WM read latency W/A with its name
drm/i915/skl: Also detect eDRAM on SKL
...
When querying the GTFIFOCTL register to check the FIFO space, the read value
must be masked. The operation is repeated explicitly in several places. This
change refactors the read-and-mask code into a function call.
v2: rebased on top of Mika's forcewake patch set, specifically:
[PATCH 8/8] drm/i915: Enum forcewake domains and domain identifiers
Change-Id: Id1a9f3785cb20b82d4caa330c37b31e4e384a3ef
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Joonas Lahtinen