Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A recent patch removed the dst_free() on the allocated
dst_entry in ipv4_blackhole_route(). The dst_free() marked the
dst_entry as dead and added it to the gc list. I.e. it was setup
for a one time usage. As a result we may now have a blackhole
route cached at a socket on some IPsec scenarios. This makes the
connection unusable.
Fix this by marking the dst_entry directly at allocation time
as 'dead', so it is used only once.
Fixes: b838d5e1c5 ("ipv4: mark DST_NOGC and remove the operation of dst_free()")
Reported-by: Tobias Brunner <tobias@strongswan.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP early demux can leverate the rx dst cache even for
multicast unconnected sockets.
In such scenario the ipv4 source address is validated only on
the first packet in the given flow. After that, when we fetch
the dst entry from the socket rx cache, we stop enforcing
the rp_filter and we even start accepting any kind of martian
addresses.
Disabling the dst cache for unconnected multicast socket will
cause large performace regression, nearly reducing by half the
max ingress tput.
Instead we factor out a route helper to completely validate an
skb source address for multicast packets and we call it from
the UDP early demux for mcast packets landing on unconnected
sockets, after successful fetching the related cached dst entry.
This still gives a measurable, but limited performance
regression:
rp_filter = 0 rp_filter = 1
edmux disabled: 1182 Kpps 1127 Kpps
edmux before: 2238 Kpps 2238 Kpps
edmux after: 2037 Kpps 2019 Kpps
The above figures are on top of current net tree.
Applying the net-next commit 6e617de84e ("net: avoid a full
fib lookup when rp_filter is disabled.") the delta with
rp_filter == 0 will decrease even more.
Fixes: 421b3885bf ("udp: ipv4: Add udp early demux")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on yet another syzkaller report, I found
that our IP_MAX_MTU enforcements were not properly done.
gcc seems to reload dev->mtu for min(dev->mtu, IP_MAX_MTU), and
final result can be bigger than IP_MAX_MTU :/
This is a problem because device mtu can be changed on other cpus or
threads.
While this patch does not fix the issue I am working on, it is
probably worth addressing it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"ip route get $daddr iif eth0 from $saddr" causes:
BUG: KASAN: use-after-free in ip_route_input_rcu+0x1535/0x1b50
Call Trace:
ip_route_input_rcu+0x1535/0x1b50
ip_route_input_noref+0xf9/0x190
tcp_v4_early_demux+0x1a4/0x2b0
ip_rcv+0xbcb/0xc05
__netif_receive_skb+0x9c/0xd0
netif_receive_skb_internal+0x5a8/0x890
Problem is that inet_rtm_getroute calls either ip_route_input_rcu (if an
iif was provided) or ip_route_output_key_hash_rcu.
But ip_route_input_rcu, unlike ip_route_output_key_hash_rcu, already
associates the dst_entry with the skb. This clears the SKB_DST_NOREF
bit (i.e. skb_dst_drop will release/free the entry while it should not).
Thus only set the dst if we called ip_route_output_key_hash_rcu().
I tested this patch by running:
while true;do ip r get 10.0.1.2;done > /dev/null &
while true;do ip r get 10.0.1.2 iif eth0 from 10.0.1.1;done > /dev/null &
... and saw no crash or memory leak.
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: David Ahern <dsahern@gmail.com>
Fixes: ba52d61e0f ("ipv4: route: restore skb_dst_set in inet_rtm_getroute")
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt_iif is going to be set to either 0 or orig_oif. If orig_oif
is 0 it amounts to the same end result so remove the check.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attempts to connect to a local address with a socket bound
to a device with the local address hangs if there is no listener:
$ ip addr sh dev eth1
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether 02:e0:f9:1c:00:37 brd ff:ff:ff:ff:ff:ff
inet 10.100.1.4/24 scope global eth1
valid_lft forever preferred_lft forever
inet6 2001:db8:1::4/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe1c:37/64 scope link
valid_lft forever preferred_lft forever
$ vrf-test -I eth1 -r 10.100.1.4
<hangs when there is no server>
(don't let the command name fool you; vrf-test works without vrfs.)
The problem is that the original intended device, eth1 in this case, is
lost when the tcp reset is sent, so the socket lookup does not find a
match for the reset and the connect attempt hangs. Fix by adjusting
orig_oif for local traffic to the device from the fib lookup result.
With this patch you get the more user friendly:
$ vrf-test -I eth1 -r 10.100.1.4
connect failed: 111: Connection refused
orig_oif is saved to the newly created rtable as rt_iif and when set
it is used as the dif for socket lookups. It is set based on flowi4_oif
passed in to ip_route_output_key_hash_rcu and will be set to either
the loopback device, an l3mdev device, nothing (flowi4_oif = 0 which
is the case in the example above) or a netdev index depending on the
lookup path. In each case, resetting orig_oif to the device in the fib
result for the RTN_LOCAL case allows the actual device to be preserved
as the skb tx and rx is done over the loopback or VRF device.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows us to later indicate to rtnetlink core that certain
doit functions should be called without acquiring rtnl_mutex.
This change should have no effect, we simply replace the last (now
unused) calcit argument with the new flag.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
callers can more safely get random bytes if they can block until the
CRNG is initialized.
Also print a warning if get_random_*() is called before the CRNG is
initialized. By default, only one single-line warning will be printed
per boot. If CONFIG_WARN_ALL_UNSEEDED_RANDOM is defined, then a
warning will be printed for each function which tries to get random
bytes before the CRNG is initialized. This can get spammy for certain
architecture types, so it is not enabled by default.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAllqXNUACgkQ8vlZVpUN
gaPtAgf/aUbXZuWYsDQzslHsbzEWi+qz4QgL885/w4L00pEImTTp91Q06SDxWhtB
KPvGnZHS3IofxBh2DC+6AwN6dPMoWDCfYhhO6po3FSz0DiPRIQCTuvOb8fhKY1X7
rTdDq2xtDxPGxJ25bMJtlrgzH2XlXPpVyPUeoc9uh87zUK5aesXpUn9kBniRexoz
ume+M/cDzPKkwNQpbLq8vzhNjoWMVv0FeW2akVvrjkkWko8nZLZ0R/kIyKQlRPdG
LZDXcz0oTHpDS6+ufEo292ZuWm2IGer2YtwHsKyCAsyEWsUqBz2yurtkSj3mAVyC
hHafyS+5WNaGdgBmg0zJxxwn5qxxLg==
=ua7p
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random updates from Ted Ts'o:
"Add wait_for_random_bytes() and get_random_*_wait() functions so that
callers can more safely get random bytes if they can block until the
CRNG is initialized.
Also print a warning if get_random_*() is called before the CRNG is
initialized. By default, only one single-line warning will be printed
per boot. If CONFIG_WARN_ALL_UNSEEDED_RANDOM is defined, then a
warning will be printed for each function which tries to get random
bytes before the CRNG is initialized. This can get spammy for certain
architecture types, so it is not enabled by default"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: reorder READ_ONCE() in get_random_uXX
random: suppress spammy warnings about unseeded randomness
random: warn when kernel uses unseeded randomness
net/route: use get_random_int for random counter
net/neighbor: use get_random_u32 for 32-bit hash random
rhashtable: use get_random_u32 for hash_rnd
ceph: ensure RNG is seeded before using
iscsi: ensure RNG is seeded before use
cifs: use get_random_u32 for 32-bit lock random
random: add get_random_{bytes,u32,u64,int,long,once}_wait family
random: add wait_for_random_bytes() API
Using get_random_int here is faster, more fitting of the use case, and
just as cryptographically secure. It also has the benefit of providing
better randomness at early boot, which is when many of these structures
are assigned.
Also, semantically, it's not really proper to have been assigning an
atomic_t in this way before, even if in practice it works fine.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
DST_NOCACHE flag check has been removed from dst_release() and
dst_hold_safe() in a previous patch because all the dst are now ref
counted properly and can be released based on refcnt only.
Looking at the rest of the DST_NOCACHE use, all of them can now be
removed or replaced with other checks.
So this patch gets rid of all the DST_NOCACHE usage and remove this flag
completely.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all the components have been changed to release dst based on
refcnt only and not depend on dst gc anymore, we can remove the
temporary flag DST_NOGC.
Note that we also need to remove the DST_NOCACHE check in dst_release()
and dst_hold_safe() because now all the dst are released based on refcnt
and behaves as DST_NOCACHE.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the previous preparation patches, we are ready to get rid of the
dst gc operation in ipv4 code and release dst based on refcnt only.
So this patch adds DST_NOGC flag for all IPv4 dst and remove the calls
to dst_free().
At this point, all dst created in ipv4 code do not use the dst gc
anymore and will be destroyed at the point when refcnt drops to 0.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch checks all the calls to
dst_hold()/skb_dst_force()/dst_clone()/dst_use() to see if
dst_hold_safe() is needed to avoid double free issue if dst
gc is removed and dst_release() directly destroys dst when
dst->__refcnt drops to 0.
In tx path, TCP hold sk->sk_rx_dst ref count and also hold sock_lock().
UDP and other similar protocols always hold refcount for
skb->_skb_refdst. So both paths seem to be safe.
In rx path, as it is lockless and skb_dst_set_noref() is likely to be
used, dst_hold_safe() should always be used when trying to hold dst.
In the routing code, if dst is held during an rcu protected session, it
is necessary to call dst_hold_safe() as the current dst might be in its
rcu grace period.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the intend of this patch series is to completely remove dst gc,
we need to call dst_dev_put() to release the reference to dst->dev
when removing routes from fib because we won't keep the gc list anymore
and will lose the dst pointer right after removing the routes.
Without the gc list, there is no way to find all the dst's that have
dst->dev pointing to the going-down dev.
Hence, we are doing dst_dev_put() immediately before we lose the last
reference of the dst from the routing code. The next dst_check() will
trigger a route re-lookup to find another route (if there is any).
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In IPv4 routing code, fib_nh and fib_nh_exception can hold pointers
to struct rtable but they never increment dst->__refcnt.
This leads to the need of the dst garbage collector because when user
is done with this dst and calls dst_release(), it can only decrement
dst->__refcnt and can not free the dst even it sees dst->__refcnt
drops from 1 to 0 (unless DST_NOCACHE flag is set) because the routing
code might still hold reference to it.
And when the routing code tries to delete a route, it has to put the
dst to the gc_list if dst->__refcnt is not yet 0 and have a gc thread
running periodically to check on dst->__refcnt and finally to free dst
when refcnt becomes 0.
This patch increments dst->__refcnt when
fib_nh/fib_nh_exception holds reference to this dst and properly release
the dst when fib_nh/fib_nh_exception has been updated with a new dst.
This patch is a preparation in order to fully get rid of dst gc later.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Existing ipv4/6_blackhole_route() code generates a blackhole route
with dst->dev pointing to the passed in dst->dev.
It is not necessary to hold reference to the passed in dst->dev
because the packets going through this route are dropped anyway.
A loopback interface is good enough so that we don't need to worry about
releasing this dst->dev when this dev is going down.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
recent updates to inet_rtm_getroute dropped skb_dst_set in
inet_rtm_getroute. This patch restores it because it is
needed to release the dst correctly.
Fixes: 3765d35ed8 ("net: ipv4: Convert inet_rtm_getroute to rcu versions of route lookup")
Reported-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping changes in drivers/net/phy/marvell.c, bug fix in 'net'
restricting a HW workaround alongside cleanups in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey Konovalov reported crashes in ipv4_mtu()
I could reproduce the issue with KASAN kernels, between
10.246.7.151 and 10.246.7.152 :
1) 20 concurrent netperf -t TCP_RR -H 10.246.7.152 -l 1000 &
2) At the same time run following loop :
while :
do
ip ro add 10.246.7.152 dev eth0 src 10.246.7.151 mtu 1500
ip ro del 10.246.7.152 dev eth0 src 10.246.7.151 mtu 1500
done
Cong Wang attempted to add back rt->fi in commit
82486aa6f1 ("ipv4: restore rt->fi for reference counting")
but this proved to add some issues that were complex to solve.
Instead, I suggested to add a refcount to the metrics themselves,
being a standalone object (in particular, no reference to other objects)
I tried to make this patch as small as possible to ease its backport,
instead of being super clean. Note that we believe that only ipv4 dst
need to take care of the metric refcount. But if this is wrong,
this patch adds the basic infrastructure to extend this to other
families.
Many thanks to Julian Anastasov for reviewing this patch, and Cong Wang
for his efforts on this problem.
Fixes: 2860583fe8 ("ipv4: Kill rt->fi")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to return matched fib result when RTM_F_FIB_MATCH
flag is specified in RTM_GETROUTE request. This is useful for user-space
applications/controllers wanting to query a matching route.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert inet_rtm_getroute to use ip_route_input_rcu and
ip_route_output_key_hash_rcu passing the fib_result arg to both.
The rcu lock is held through the creation of the response, so the
rtable/dst does not need to be attached to the skb and is passed
to rt_fill_info directly.
In converting from ip_route_output_key to ip_route_output_key_hash_rcu
the xfrm_lookup_route in ip_route_output_flow is dropped since
flowi4_proto is not set for a route get request.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt_fill_info has 1 caller with the event set to RTM_NEWROUTE. Given that
remove the arg and use RTM_NEWROUTE directly in rt_fill_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A later patch wants access to the fib result on an input route lookup
with the rcu lock held. Refactor ip_route_input_noref pushing the logic
between rcu_read_lock ... rcu_read_unlock into a new helper that takes
the fib_result as an input arg.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A later patch wants access to the fib result on an output route lookup
with the rcu lock held. Refactor __ip_route_output_key_hash, pushing
the logic between rcu_read_lock ... rcu_read_unlock into a new helper
with the fib_result as an input arg.
To keep the name length under control remove the leading underscores
from the name and add _rcu to the name of the new helper indicating it
is called with the rcu read lock held.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David reported that doing the following:
ip li add red type vrf table 10
ip link set dev eth1 vrf red
ip addr add 127.0.0.1/8 dev red
ip link set dev eth1 up
ip li set red up
ping -c1 -w1 -I red 127.0.0.1
ip li del red
when either policy routing IP rules are present or the local table
lookup ip rule is before the l3mdev lookup results in a hang with
these messages:
unregister_netdevice: waiting for red to become free. Usage count = 1
The problem is caused by caching the dst used for sending the packet
out of the specified interface on a local route with a different
nexthop interface. Thus the dst could stay around until the route in
the table the lookup was done is deleted which may be never.
Address the problem by not forcing output device to be the l3mdev in
the flow's output interface if the lookup didn't use the l3mdev. This
then results in the dst using the right device according to the route.
Changes in v2:
- make the dev_out passed in by __ip_route_output_key_hash correct
instead of checking the nh dev if FLOWI_FLAG_SKIP_NH_OIF is set as
suggested by David.
Fixes: 5f02ce24c2 ("net: l3mdev: Allow the l3mdev to be a loopback")
Reported-by: David Ahern <dsa@cumulusnetworks.com>
Suggested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netlink_ext_ack arg to rtnl_doit_func. Pass extack arg to nlmsg_parse
for doit functions that call it directly.
This is the first step to using extended error reporting in rtnetlink.
>From here individual subsystems can be updated to set netlink_ext_ack as
needed.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the new extended ACK reporting struct to all of the generic
netlink parsing functions. For now, pass NULL in almost all callers
(except for some in the core.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Don't get the metric RTAX_ADVMSS of dst.
There are two reasons.
1) Its caller dst_metric_advmss has already invoke dst_metric_advmss
before invoke default_advmss.
2) The ipv4_default_advmss is used to get the default mss, it should
not try to get the metric like ip6_default_advmss.
2. Use sizeof(tcphdr)+sizeof(iphdr) instead of literal 40.
3. Define one new macro IPV4_MAX_PMTU instead of 65535 according to
RFC 2675, section 5.1.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_rtm_getroute synthesizes a skeletal ICMP skb, which is passed to
ip_route_input when iif is given. If a multipath route is present for
the designated destination, fib_multipath_hash ends up being called with
that skb. However, as that skb contains no information beyond the
protocol type, the calculated hash does not match the one we would see
for a real packet.
There is currently no way to fix this for layer 4 hashing, as
RTM_GETROUTE doesn't have the necessary information to create layer 4
headers. To fix this for layer 3 hashing, set appropriate saddr/daddrs
in the skb and also change the protocol to UDP to avoid special
treatment for ICMP.
Signed-off-by: Florian Larysch <fl@n621.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_rtm_getroute synthesizes a skeletal ICMP skb, which is passed to
ip_route_input when iif is given. If a multipath route is present for
the designated destination, ip_multipath_icmp_hash ends up being called,
which uses the source/destination addresses within the skb to calculate
a hash. However, those are not set in the synthetic skb, causing it to
return an arbitrary and incorrect result.
Instead, use UDP, which gets no such special treatment.
Signed-off-by: Florian Larysch <fl@n621.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ECMP hash policy choice via a new sysctl
called fib_multipath_hash_policy and also adds support for L4 hashes.
The current values for fib_multipath_hash_policy are:
0 - layer 3 (default)
1 - layer 4
If there's an skb hash already set and it matches the chosen policy then it
will be used instead of being calculated (currently only for L4).
In L3 mode we always calculate the hash due to the ICMP error special
case, the flow dissector's field consistentification should handle the
address order thus we can remove the address reversals.
If the skb is provided we always use it for the hash calculation,
otherwise we fallback to fl4, that is if skb is NULL fl4 has to be set.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restore the lost masking of TOS in input route code to
allow ip rules to match it properly.
Problem [1] noticed by Shmulik Ladkani <shmulik.ladkani@gmail.com>
[1] http://marc.info/?t=137331755300040&r=1&w=2
Fixes: 89aef8921b ("ipv4: Delete routing cache.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid matching of random stack value for uid when rules
are looked up on input route or when RP filter is used.
Problem should affect only setups that use ip rules with
uid range.
Fixes: 622ec2c9d5 ("net: core: add UID to flows, rules, and routes")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add confirm_neigh method to dst_ops and use it from IPv4 and IPv6
to lookup and confirm the neighbour. Its usage via the new helper
dst_confirm_neigh() should be restricted to MSG_PROBE users for
performance reasons.
For XFRM prefer the last tunnel address, if present. With help
from Steffen Klassert.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtm_table is an 8-bit field while table ids are allowed up to u32. Commit
709772e6e0 ("net: Fix routing tables with id > 255 for legacy software")
added the preference to set rtm_table in dumps to RT_TABLE_COMPAT if the
table id is > 255. The table id returned on get route requests should do
the same.
Fixes: c36ba6603a ("net: Allow user to get table id from route lookup")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing about the route lookup requires bottom half to be disabled.
Remove the local_bh_disable ... local_bh_enable around ip_route_input.
This appears to be a vestige of days gone by as it has been there
since the beginning of git time.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipmr_get_route has 1 caller and the nowait arg is 0. Remove the arg and
simplify ipmr_get_route accordingly.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt_fill_info has only 1 caller and both of the last 2 args -- nowait
and flags -- are hardcoded to 0. Given that remove them as input arguments
and simplify rt_fill_info accordingly.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 output routes already use l3mdev device instead of loopback for dst's
if it is applicable. Change local input routes to do the same.
This fixes icmp responses for unreachable UDP ports which are directed
to the wrong table after commit 9d1a6c4ea4 because local_input
routes use the loopback device. Moving from ingress device to loopback
loses the L3 domain causing responses based on the dst to get to lost.
Fixes: 9d1a6c4ea4 ("net: icmp_route_lookup should use rt dev to
determine L3 domain")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit e2d118a1cb ("net: inet: Support UID-based routing in IP
protocols.") made ip_do_redirect call sock_net(sk) to determine
the network namespace of the passed-in socket. This crashes if sk
is NULL.
Fix this by getting the network namespace from the skb instead.
Fixes: e2d118a1cb ("net: inet: Support UID-based routing in IP protocols.")
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Rutland