Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
While at it, stop setting already set HUB_CHAR_INDV_PORT_LPSM once again.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
While at it, fix the indentation.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
While at it, stop setting already set HUB_CHAR_INDV_PORT_LPSM once again.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
While at it, avoid duplicate computation when calling DBG().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When re-applying the configuration after a successful usb device reset,
xhci_discover_or_reset_device has already dropped the endpoints, and free-ed
the rings.
The endpoints already being dropped is expected, and should not lead to
warnings. Use the fact that the rings are also free-ed in this scenario to
detect this, and suppress the "xHCI xhci_drop_endpoint called with disabled
ep ..." message in this case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
--
Changes in v2:
Move the ring check to only guard the xhci_warn, so as to avoid side-effects
in case we have a scenario where the rings are free-ed, but the endpoint is
not yet dropped.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To help debugging xhci problems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB stack provides a mechanism for drivers to request an
asynchronous device reset (usb_queue_reset_device()). The mechanism
uses a work item (reset_ws) embedded in the usb_interface structure
used by the driver, and the reset is carried out by a work queue
routine.
The asynchronous reset can race with driver unbinding. When this
happens, we try to cancel the queued reset before unbinding the
driver, on the theory that the driver won't care about any resets once
it is unbound.
However, thanks to the fact that lockdep now tracks work queue
accesses, this can provoke a lockdep warning in situations where the
device reset causes another interface's driver to be unbound; see
http://marc.info/?l=linux-usb&m=141893165203776&w=2
for an example. The reason is that the work routine for reset_ws in
one interface calls cancel_queued_work() for the reset_ws in another
interface. Lockdep thinks this might lead to a work routine trying to
cancel itself. The simplest solution is not to cancel queued resets
when unbinding drivers.
This means we now need to acquire a reference to the usb_interface
when queuing a reset_ws work item and to drop the reference when the
work routine finishes. We also need to make sure that the
usb_interface structure doesn't outlive its parent usb_device; this
means acquiring and dropping a reference when the interface is created
and destroyed.
In addition, cancelling a queued reset can fail (if the device is in
the middle of an earlier reset), and this can cause usb_reset_device()
to try to rebind an interface that has been deallocated (see
http://marc.info/?l=linux-usb&m=142175717016628&w=2 for details).
Acquiring the extra references prevents this failure.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Reported-by: Olivier Sobrie <olivier@sobrie.be>
Tested-by: Olivier Sobrie <olivier@sobrie.be>
Cc: stable <stable@vger.kernel.org> # 3.19
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci-octeon driver used a 64-bit dma_mask. With removal of ehci-octeon
and usage of ehci-platform ehci dma_mask is now limited to 32 bits
(coerced in ehci_platform_probe).
Provide a flag in ehci platform data to allow use of 64 bits for
dma_mask.
Cc: David Daney <david.daney@cavium.com>
Cc: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'len' variable in fhci_hub_control() is write-only, so totally useless.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code handling Get Hub Descriptor request copies data from root_hub_des[],
then overwrites byte 3 with real 'wHubCharacteristics' value. There's no need
to overwrite, we can substitute the real value right into root_hub_des[3].
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
__uvcg_fill_strm() called from __uvcg_iter_stream_cls()
might have advanced the "data" even if __uvcg_iter_stream_cls()
returns an error, so use a backup copy as an argument to kfree().
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 0cf884e819.
Even after applying the follow-on patch at
https://patchwork.kernel.org/patch/5325111
there are still problems with device connect on the Altera SOCFPGA
platform at least. One possible fix would be to add a whitelist
to enable suspend/resume on platforms where it does work correctly.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of custom approach the patch converts code to use %pM specifier to
print MAC.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The use of GPIOs should be optional for the generic phy, otherwise
the Altera SOCFPGA platform at least is broken.
Fixes breakage caused by a combination of e9f2cefb0c "usb: phy:
generic: migrate to gpio_desc" and 135b3c4304 "usb: dwc2: platform:
add generic PHY framework support".
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
1) Change "conv" an "vnoc" to "to_cpu_endian" to "to_little_endian".
2) No need to check the "limit" because that is already handled in
kstrtoXX so delete that parameter along with the check.
3) By using a "bits" parameter, we can combine the "uxx" parameter and
the "str2u" parameters.
4) The kstrtou##bits() conversion does not need to be done under the
mutex so move it to the start of the function.
5) Change the name of "identity_conv" to "noop_conversion".
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to add a kfree(h) on an error path.
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
"num" is a u32 so "(num > 0xFFFFFFFF)" is never true. Also the range
is already checked in kstrtou32().
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In practice failure to find phy when requested in non-OF
case means it will never become available, so
__usb_find_phy() must return -ENODEV and not -EPROBE_DEFER.
This fixes a regression caused by commit 9c9d82492b
(usb: phy: Fix deferred probing), where the USB
controller driver is left infinitely into deferred probe
when there are no phys.
Fixes: 9c9d82492b (usb: phy: Fix deferred probing)
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We're basically saying ERR_CAST(NULL) and PTR_ERR(NULL) here, which is
nonsensical.
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following problem: data transmission in direction
IN break unless the GSNPSID register access is done with spinlock held.
This issue occurs at least in Exynos4412 SoC, probably in many SoC's
from Exynos familly.
The problem is described here:
https://lkml.org/lkml/2014/12/22/185
And there is linux mailing list discussion:
https://lkml.org/lkml/2015/1/14/17
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is old, unused code that is #defined out by the use of NOTMOS7840
and NOTMCS7840 - these are not defined anywhere.
If NOTMOS7840 is defined then the code will break on null pointer
dereferences on mos7840_port. So the code is currently unused, and
broken anyway, so why not just remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
While the code is correct and functions well, it's still
a bit misleading to add the reference operator in from of
the buf argument.
This patch simply removes that operator in order to make
use of buf slightly better to the eyes.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since we can compose gadgets from many functions, there is the problem
related to gadget breakage while FunctionFS daemon being closed. FFS
function is userspace code so there is no way to know when it will close
files (it doesn't matter what is the reason of this situation, it can
be daemon logic, program breakage, process kill or any other). So when
we have another function in gadget which, for example, sends some amount
of data, does some software update or implements some real-time functionality,
we may want to keep the gadget connected despite FFS function is no longer
functional.
We can't just remove one of functions from gadget since it has been
enumerated, so the only way to keep entire gadget working is to make
broken FFS function deactivated but still visible to host. For this
purpose this patch introduces "no_disconnect" mode. It can be enabled
by setting mount option "no_disconnect=1", and results with defering
function disconnect to the moment of reopen ep0 file or filesystem
unmount. After closing all endpoint files, FunctionFS is set to state
FFS_DEACTIVATED.
When ffs->state == FFS_DEACTIVATED:
- function is still bound and visible to host,
- setup requests are automatically stalled,
- transfers on other endpoints are refused,
- epfiles, except ep0, are deleted from the filesystem,
- opening ep0 causes the function to be closed, and then FunctionFS
is ready for descriptors and string write,
- altsetting change causes the function to be closed - we want to keep
function alive until another functions are potentialy used, altsetting
change means that another configuration is being selected or USB cable
was unplugged, which indicates that we don't need to stay longer in
FFS_DEACTIVATED state
- unmounting of the FunctionFS instance causes the function to be closed.
Tested-by: David Cohen <david.a.cohen@linux.intel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removing a few items that are not needed anymore and
adding separate function for quirks.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is nothing specific being done in the suspend and
resume callbacks that is not already taken care of in PCI
driver core, so dropping the functions.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
None of the PCI platforms need the NOP transceivers, and
since we can now live without the PHYs, removing
registration of the platform devices for them.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/gadget/function/uvc_configfs.c:46:28: sparse: symbol 'to_uvcg_control_header' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:138:25: sparse: symbol 'uvcg_control_header_type' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:164:6: sparse: symbol 'uvcg_control_header_drop' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:721:20: sparse: symbol 'to_uvcg_format' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:798:30: sparse: symbol 'to_uvcg_streaming_header' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:950:25: sparse: symbol 'uvcg_streaming_header_type' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:976:6: sparse: symbol 'uvcg_streaming_header_drop' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1020:19: sparse: symbol 'to_uvcg_frame' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1265:25: sparse: symbol 'uvcg_frame_type' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1315:6: sparse: symbol 'uvcg_frame_drop' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1338:26: sparse: symbol 'to_uvcg_uncompressed' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1548:25: sparse: symbol 'uvcg_uncompressed_type' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1586:6: sparse: symbol 'uvcg_uncompressed_drop' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1610:19: sparse: symbol 'to_uvcg_mjpeg' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1761:25: sparse: symbol 'uvcg_mjpeg_type' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1793:6: sparse: symbol 'uvcg_mjpeg_drop' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since we call gaudio_cleanup at f_audio_free, the f_uac1_opts
doesn't need to use gaudio any more.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate udc structure instead of relying on the statically declared
object.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
cpu_is_at91xxx are a set of macros defined in mach/cpu.h and are here used
to detect the SoC we are booting on.
Use compatible string + a caps structure to replace those cpu_is_xxx tests.
Remove all mach and asm headers (which are now unused).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Make use of devm_ functions to simplify probe and remove code.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Since non-DT board support has been removed from the at91 architecture we
can safely remove non-DT handling code.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Now that at91 system clocks forward set_rate request to their parent we
can remove the uclk clock and directly call clk_set_rate on fclk.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The driver is requesting clock by their global name (those declared in the
clk_lookup list), but this only works with !CCF kernels.
Now that all SoCs have moved to CCF, fix the driver to use local names
(hclk and pclk).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The final set of fixes for v3.19. Two of the fixes are
related to dwc3 scatter/gather implementation when we have
more requests queued than available TRBs, while the other
is a build fix for mv-usb PHY.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iLKs
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.19-rc6
The final set of fixes for v3.19. Two of the fixes are
related to dwc3 scatter/gather implementation when we have
more requests queued than available TRBs, while the other
is a build fix for mv-usb PHY.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here are a few fixes for reported problems including a possible
null-deref on probe with keyspan, a misbehaving modem, and a couple of
issues with the USB console.
Some new device IDs are also added.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=umHr
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v3.18-rc5
Here are a few fixes for reported problems including a possible
null-deref on probe with keyspan, a misbehaving modem, and a couple of
issues with the USB console.
Some new device IDs are also added.
Signed-off-by: Johan Hovold <johan@kernel.org>
DWC3 gadget sets up a pool of 32 TRBs for each EP during initialization. This
means, the max TRBs that can be submitted for an EP is fixed to 32. Since the
request queue for an EP is a linked list, any number of requests can be queued
to it by the gadget layer. However, the dwc3 driver must not submit TRBs more
than the pool it has created for. This limit wasn't respected when SG was used
resulting in submitting more than the max TRBs, eventually leading to
non-transfer of the TRBs submitted over the max limit.
Root cause:
When SG is used, there are two loops iterating to prepare TRBs:
- Outer loop over the request_list
- Inner loop over the SG list
The code was missing break to get out of the outer loop.
Fixes: eeb720fb21 (usb: dwc3: gadget: add support for SG lists)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When scatter gather (SG) is used, multiple TRBs are prepared from one DWC3
request (dwc3_request). So while preparing TRBs, the 'last' flag should be set
only when it is the last TRB being prepared from the last dwc3_request entry.
The current implementation uses list_is_last to check if the dwc3_request is the
last entry from the request_list. However, list_is_last returns false for the
last entry too. This is because, while preparing the first TRB from a request,
the function dwc3_prepare_one_trb modifies the request's next and prev pointers
while moving the URB to req_queued. Hence, list_is_last always returns false no
matter what.
The correct way is not to access the modified pointers of dwc3_request but to
use list_empty macro instead.
Fixes: e5ba5ec833 (usb: dwc3: gadget: fix scatter gather implementation)
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
The driver was recently adapted to a core API change, but the
change was incomplete, missing out the suspend helper and
leaving an extraneous local variable around:
usb/phy/phy-mv-usb.c: In function 'mv_otg_update_state':
usb/phy/phy-mv-usb.c:341:18: warning: unused variable 'phy' [-Wunused-variable]
usb/phy/phy-mv-usb.c: In function 'mv_otg_suspend':
usb/phy/phy-mv-usb.c:861:16: error: 'struct usb_phy' has no member named 'state'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: e47d92545c ("usb: move the OTG state from the USB PHY to the OTG structure")
Signed-off-by: Felipe Balbi <balbi@ti.com>
On the Renesas R8A7791 SoC based boards there's MAX3355 USB OTG chip and mini-AB
USB connector corresponding to USB port 0 driven either by EHCI/OHCI or Renesas
USBHS gadget controller. And we'd like the host/gadget drivers to work based on
the cable type connected. An 'extcon' driver for MAX3355 has been written, so we
only need to bind to it via device tree which I'm doing in this patch.
(Perhaps, it would also make sense to use OTG HNP when the USBHS host mode is
active and a B-cable is connected but I don't have access to host-capable USBHS,
so wouldn't be able to test it.)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If usb bus is reset without a physical disconnection, all endpoints
will remain open. Call s3c_hsotg_disconnect() from reset handler to
report a disconnect to gadget framework. hsotg->connected is checked
in s3c_hsotg_disconnect() before processing disconnect.
In some cases, USBRst is seen before EnumDone and after it as well.
So move setting of hsotg->connected to set-address to avoid reporting
extra disconnection in this case.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When booting with id pin grounded, dwc2 default to host mode.
Thus, force device mode prior initializing gadget part.
Else fifo init will fail since fifo values are not correct
in host mode.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This callback informs the driver about the total amount of current it
is allowed to draw. Share this information with the phy so that
current limits can be set for charging for example.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Gadget must be informed about disconnection when pullup is
removed.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After all endpoints are disabled, fifo_map should have reached 0.
Its a bug if if didn't, so warn about it and reset it to 0 so that
driver can continue using all the fifos.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When selecting different alt setting, s3c_hsotg_ep_enable can be
called with fifo already allocated. Allocate fifo again only if
required and after deallocating the previous fifo.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current algorithm picks the first fifo which is equal to or greater
than the required size. This can result in bigger fifos assigned to
endpoints with smaller maxps. Change the algorithm to pick the
smallest fifo which is greater than or equal to the required size.
Moreover, only use signed variables when required.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This flag is set before sending the zlp. So use present tense instead
of the past tense.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enable phy driver to report vbus session. This allows us to remove
D+ pullup when vbus is not present.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Can't stay in the loop forever. Break it after timeout.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The warning is probably good but it has false positives in both dma and non-dma
cases. So its not very helpful in either.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to programming guide, zero length packet should be
programmed on its own and should not be counted in DIEPTSIZ.PktCnt
with other packets.
For ep0, this is the zlp for DATA IN stage (if required) and not for
the STATUS stage.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Manage ep0 state in software to add handling of status OUT stage.
Just toggling hsotg->setup in s3c_hsotg_handle_outdone leaves it in
wrong state in 2-stage control transfers.
Moreover, ensure that for setup-packet s3c_hsotg_handle_outdone is
called either from SetupDone or OutDone but not both. Dwc2 ip v3.00a
generates both SetupDone and OutDone on setup packets.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
kill_all_requests() can flush the fifo. Call it after disabling the
endpoint.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When matching tx fifo to endpoint, consider all fifos instead of
hard limiting to 8
Moreover, print error in case no fifo could be found.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
< 15 check doesn't show debug information for endpoint 15.
It is possible to have less than 15 endpoints so use limit
provided by hardware configuration.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These members are only occupying space.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As fifo size can vary between SOCs, add possibility to configure
them from device tree. Fifo sizes used by the legacy driver will
be used If they are not provided by the device tree.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current code does not check endpoint 15 interrupt. Use number
of endpoint configured in hardware instead of the hardcoded value.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
GHWCFG1 provides hardware configuration of each endpoint. Use
it to configure the endpoints instead of assuming all even
endpoint are OUT and all odd endpoints are IN.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
* Add an of specific function to parse device node properties.
* Enable dma usage only if device tree property 'g_use_dma' is present.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Do a read-modify-write instead of only setting DMAEn bit.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
HBstLen is GAHBCFG[4:1]. Use GAHBCFG_HBSTLEN_SHIFT to write burst-
length at correct position.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In the error path, s3c_hsotg_phy_disable should be called after a
call to s3c_hsotg_phy_enable is made.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When using DMA, data of the previous setup packet can be read back
from cache because ep0 and ctrl buffers are embedded in struct s3c_hsotg.
Allocate buffers instead of embedding them.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Only process DOEPINT.XferCompl on data packet as DOEPINTn.SetUp can
occur with or without DOEPINT.XferCompl. When DOEPINT.SetUp occurs
with DOEPINT.XferCompl, only DOEPINT.SetUp needs to be handled.
Moreover, ignore DOEPINT.XferCompl when it occurs with
DOEPINT.StupPktRcvd as driver needs to wait for DOEPINT.SetUp to
continue.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When using DMA, keep fifo empty interrupt disabled. Otherwise
core is flooded by interrupts.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Bind peripheral controller to the phy on udc_start. Unbind on
udc_stop.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just three fixes this time. An oops fix in ep_write() from gadgetfs,
another oops for the Atmel UDC when unloading a gadget driver and
the fix for PHY deferred probing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7Fj7
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.19-rc5
Just three fixes this time. An oops fix in ep_write() from gadgetfs,
another oops for the Atmel UDC when unloading a gadget driver and
the fix for PHY deferred probing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/phy/phy.c
UDC core has already done it before .udc_stop and after .udc_start.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
UDC core has already done it before .udc_stop and after .udc_start.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of using variable length array, use a static length equal to
the size of the ffs->ev.types array. This gets rid of a sparse warning:
drivers/usb/gadget/function/f_fs.c:401:44: warning:
Variable length array is used.
and makes it more explicit that the array has a very tight upper size
limit. Also add some more documentation about the ev.types array and
how its size is limited and affects the rest of the code.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Rohith Seelaboyina <rseelaboyina@nvidia.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for vbus detection and power supply. This code is more or
less stolen from phy-gpio-vbus-usb.c, and aims at providing a detection
mechanism for VBus (ie. usb cable plug) based on a GPIO line, and a
power supply activation which draws current from the VBus.
[ balbi@ti.com : fix build break ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Change internal gpio handling from integer gpios into gpio
descriptors. This change only addresses the internal API and
device-tree/ACPI, while the legacy platform data remains integer space
based.
This change is only build compile tested, and very prone to error. I
leave this comment for now in the commit message so that this patch gets
some testing as I'm pretty sure it's buggy.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Cache INT_ENB register value in order to avoid uncached iomem access, and
thus improve access time to INT_ENB value.
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Avoid interpreting useless status flags when we're not waiting for such
events by masking the status variable with the interrupt enabled register
value.
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reported-by: Patrice VILCHEZ <patrice.vilchez@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
at91sam9g45 and at91sam9x5 SoCs have an hardware bug forcing us to
generate a pulse on the BIAS signal on "USB end of reset” and
“USB end of resume" events.
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reported-by: Patrice VILCHEZ <patrice.vilchez@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
at91sam9rl SoC has an erratum forcing us to toggle the BIAS on USB
suspend/resume events.
This specific handling is only activated when CONFIG_ARCH_AT91SAM9RL is
set and this option is only set when building a non-DT kernel, which is
problematic since non-DT support for at91sam9rl SoC has been removed.
Rework the toggle_bias implementation to attach it to the "at91sam9rl-udc"
compatible string.
Add new compatible strings to avoid executing at91sam9rl erratum handling
on other SoCs.
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removes some functions that are not used anywhere:
fsl_otg_tick_timer() view_ulpi()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For some user cases, like plug out and replug in usb device during
the system suspend, the speed negotiation will be error due to host
doesn't know the device's disconnection, and it still hopes the
high speed device, but the device backs to "powered" state which
its high speed termination is not enabled, the usb core calls
the PHY's disconnect notifier with "full speed", it will NOT
take effect at all.
If the usb core calls disconnect notifer, the port change must happen,
so it is safe to disable high speed disconenct detector, since
connect notifier will be called soon if the device is still connected
on the port, and we will enable high speed disconnect detector at that
time.
Acked-by: Li Jun <b47624@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we shut down the PHY, we need to power down all PHY's functions
as well as disable wakeup, it is the opposite operation we do at .init.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes in simpler way the bug described in [1] and [2]. It
looks like DWC2 is the only UDC driver that doesn't force usb requests
to complete in ep_disable() function. This causes described problem,
because we have no guarantee that all requests will be completed before
unbind of usb function.
To fix this problem we force all requests of disabled endpoint to complete.
Also currently running request is not handled. This allowed to simplify
code of kill_all_requests() function, because 'force' parameter is always
set to true, so we don't need it anymore.
In s3c_hsotg_rx_data() we change function used to print message when active
request is NULL from dev_warn() to dev_dbg(), because such situation is
harmless for driver and now it can take place during normal endpoint
disabling.
[1] https://lkml.org/lkml/2014/12/9/283
[2] https://lkml.org/lkml/2014/12/12/360
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some debug messages were not build due to unconditional #if 0.
These messages are very useful for debugging and the user can enable
them on demand via dynamic debug.
If they are not enabled the performance is not affected.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ASSERT_OUT_NAKING was only called by out_flush and was hidden behind a
ifdef.
This patch moves the inline function into out_flush and remove the
ifdef. The user can decide to print the debug message or not via dynamic
printk
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After fix superspeed dma_done was applied we can simplify the code by
removing the duplicated dma_done and letting the function check if there
are more completed dma transactions.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The function is very simple, does not declare any variable and it is
called in the irq path.
The counterpart for net228x is already declared as inline.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Function resume_dma is not used, remove it.
The reason the compiler did not catch this dead code is the inline
modifier.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Once the defect 7374 is patched, there is no reason the keep reading the
idx scratch register.
Cache the content of the scratch idx register on device flag.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Do not duplicate the code for the else branch of the condition.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We can use the same function for both families of chips and also remove
the ep_stop_dma() function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
irqs_superspeed calls ep_stall instead of set/clear_halt, due to a
workaround for SS seqnum. Create a function with the workaround and
call set/clear_halt instead.
This way we can compare the code of super/normal speed and it is easier
to follow the code.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Field is_halt is never used by any function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ep_stdrsp was only called by handle_stat0_irqs_superspeed and with
always the same flags.
Remove the function and replace the call by the code inside the
function, since it is very simple once the dead code is removed.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
restart_dma is not used before it is declaration. Therefore we can
remove this definition.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove dma_started field from net2280_ep structure, since it is not used
by any function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
use_dma parameter was designed to enable the dma on the chip. It was
enabled by default.
It comes from the time when the dma was not reliable. Now it has been
working ok in production.
This patch removes this parameter.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Parameter use_msi was used to enable msi irq on usb338x chips, it was
enabled by default.
There is no reason to prefer non-msi irq on usb338x, and it falls back
to non msi on error.
Therefore remove this option.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the full_speed parameter used force full-speed
operation.
It was designed exclusively for testing purposes, and there is no
reason to maintain this in a production kernel.
Reverts: 2f07607747
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
use_dma_chaining module parameter was designed to avoid creating one irq
per package on a group of packages (with the help of the driver's flag
no_interrupt).
Unfortunately, when this parameter is enabled, the driver fails to work
on both net2280 and 3380 chips.
This patch removes this parameter, which was disabled by default.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a typo ("prove" instead of "probe") in the error message printed when
the platform initialization fails. Replace that word with more fitting "init".
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fixups for incorrect use of DECLARE_COMPLETION. see also commit
6e9a4738 ("completions: lockdep annotate on stack completions")
patch is against 3.18.0 linux-next
This was only code reviewed and compile tested
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Update this according to USB Audio Class 1.0 spec. This fixes the Windows 7
detection issue.
Cc: Rafael Brune <mail@rbrune.de>
Signed-off-by: Xuebing Wang <xbing6@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
(Fixed some code style issues)
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
UAC1 forget to do it.
Signed-off-by: Xuebing Wang <xbing6@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
"ep" isn't NULL here, and static checkers complain because we
dereferenced it on the previous line.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We already know what "value" is, so there is no need to check. It
puzzles static checkers to have the unneeded condition.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Get PHY parameters from devicetree and power off usb PHY during
system suspend.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for using the uvc function as a component of USB gadgets composed
with configfs.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the caller of uvc_alloc() does not provide enough
descriptors, binding the function should fail, so appropriate
code is returned from uvc_copy_descriptors().
uvc_function_bind() is modified accordingly to account for possible
errors from uvc_copy_descriptors().
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When configfs is integrated, CONFIGFS_ATTR_STRUCT and CONFIGFS_ATTR_OPS
macros should be used, but the latter expects that tere is a to_f_uvc_opts
function accepting a config_item, whereas the macro being changed
can be applied to a different type of argument.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
usbhsc_drvcllbck_notify_hotplug() always returns 0, so it's rather pointless to
store and check its result for being < 0.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A maximum value which fits in 16 bits, unsigned, is 65535.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_gadget_init_hw_endpoints calls dwc3_alloc_trb_pool only if epnum is not
equal to 0 or 1. Hence, rechecking it in the called function is redundant.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removes some functions that are not used anywhere:
s3c2410_udc_clear_ep_state() s3c2410_udc_set_ep0_sse_out()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If a USB serial device (e.g. /dev/ttyUSB0) with an active program is
unplugged, an -ENODEV (19) error will be produced after it gives up
trying to resubmit a read.
usb_serial_generic_submit_read_urb - usb_submit_urb failed: -19
Add -ENODEV as one of the permanent errors along with -EPERM that
usb_serial_generic_submit_read_urb() handles quietly without an error.
Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
If a USB serial device is unplugged while there is an active program
using the device it may spam the logs with -EPROTO (71) messages as it
attempts to retry.
Most serial usb drivers (metro-usb, pl2303, mos7840, ...) only output
these messages for debugging. The generic driver treats these as
errors.
Change the default output for the generic serial driver from error to
debug to silence these non-critical errors.
Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use tty kref to release the fake tty in usb_console_setup to avoid use
after free if the underlying serial driver has acquired a reference.
Note that using the tty destructor release_one_tty requires some more
state to be initialised.
Fixes: 4a90f09b20 ("tty: usb-serial krefs")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB console currently allocates a temporary fake tty which is used
to pass terminal settings to the underlying serial driver.
The tty struct is not fully initialised, something which can lead to a
lockdep warning (or worse) if a serial driver tries to acquire a
line-discipline reference:
usbserial: USB Serial support registered for pl2303
pl2303 1-2.1:1.0: pl2303 converter detected
usb 1-2.1: pl2303 converter now attached to ttyUSB0
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 68 Comm: udevd Tainted: G W 3.18.0-rc5 #10
[<c0016f04>] (unwind_backtrace) from [<c0013978>] (show_stack+0x20/0x24)
[<c0013978>] (show_stack) from [<c0449794>] (dump_stack+0x24/0x28)
[<c0449794>] (dump_stack) from [<c006f730>] (__lock_acquire+0x1e50/0x2004)
[<c006f730>] (__lock_acquire) from [<c0070128>] (lock_acquire+0xe4/0x18c)
[<c0070128>] (lock_acquire) from [<c027c6f8>] (ldsem_down_read_trylock+0x78/0x90)
[<c027c6f8>] (ldsem_down_read_trylock) from [<c027a1cc>] (tty_ldisc_ref+0x24/0x58)
[<c027a1cc>] (tty_ldisc_ref) from [<c0340760>] (usb_serial_handle_dcd_change+0x48/0xe8)
[<c0340760>] (usb_serial_handle_dcd_change) from [<bf000484>] (pl2303_read_int_callback+0x210/0x220 [pl2303])
[<bf000484>] (pl2303_read_int_callback [pl2303]) from [<c031624c>] (__usb_hcd_giveback_urb+0x80/0x140)
[<c031624c>] (__usb_hcd_giveback_urb) from [<c0316fc0>] (usb_giveback_urb_bh+0x98/0xd4)
[<c0316fc0>] (usb_giveback_urb_bh) from [<c0042e44>] (tasklet_hi_action+0x9c/0x108)
[<c0042e44>] (tasklet_hi_action) from [<c0042380>] (__do_softirq+0x148/0x42c)
[<c0042380>] (__do_softirq) from [<c00429cc>] (irq_exit+0xd8/0x114)
[<c00429cc>] (irq_exit) from [<c007ae58>] (__handle_domain_irq+0x84/0xdc)
[<c007ae58>] (__handle_domain_irq) from [<c000879c>] (omap_intc_handle_irq+0xd8/0xe0)
[<c000879c>] (omap_intc_handle_irq) from [<c0014544>] (__irq_svc+0x44/0x7c)
Exception stack(0xdf4e7f08 to 0xdf4e7f50)
7f00: debc0b80 df4e7f5c 00000000 00000000 debc0b80 be8da96c
7f20: 00000000 00000128 c000fc84 df4e6000 00000000 df4e7f94 00000004 df4e7f50
7f40: c038ebc0 c038d74c 600f0013 ffffffff
[<c0014544>] (__irq_svc) from [<c038d74c>] (___sys_sendmsg.part.29+0x0/0x2e0)
[<c038d74c>] (___sys_sendmsg.part.29) from [<c038ec08>] (SyS_sendmsg+0x18/0x1c)
[<c038ec08>] (SyS_sendmsg) from [<c000fa00>] (ret_fast_syscall+0x0/0x48)
console [ttyUSB0] enabled
Fixes: 36697529b5 ("tty: Replace ldisc locking with ldisc_sem")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
When unloading the module 'g_hid.ko', the urb request will be dequeued and the
completion routine will be excuted. If there is no urb packet, the urb request
will not be added to the endpoint queue and the completion routine pointer in
urb request is NULL.
Accessing to this NULL function pointer will cause the Oops issue reported
below.
Add the code to check if the urb request is in the endpoint queue
or not. If the urb request is not in the endpoint queue, a negative
error code will be returned.
Here is the Oops log:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = dedf0000
[00000000] *pgd=3ede5831, *pte=00000000, *ppte=00000000
Internal error: Oops: 80000007 [#1] ARM
Modules linked in: g_hid(-) usb_f_hid libcomposite
CPU: 0 PID: 923 Comm: rmmod Not tainted 3.18.0+ #2
Hardware name: Atmel SAMA5 (Device Tree)
task: df6b1100 ti: dedf6000 task.ti: dedf6000
PC is at 0x0
LR is at usb_gadget_giveback_request+0xc/0x10
pc : [<00000000>] lr : [<c02ace88>] psr: 60000093
sp : dedf7eb0 ip : df572634 fp : 00000000
r10: 00000000 r9 : df52e210 r8 : 60000013
r7 : df6a9858 r6 : df52e210 r5 : df6a9858 r4 : df572600
r3 : 00000000 r2 : ffffff98 r1 : df572600 r0 : df6a9868
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c53c7d Table: 3edf0059 DAC: 00000015
Process rmmod (pid: 923, stack limit = 0xdedf6230)
Stack: (0xdedf7eb0 to 0xdedf8000)
7ea0: 00000000 c02adbbc df572580 deced608
7ec0: df572600 df6a9868 df572634 c02aed3c df577c00 c01b8608 00000000 df6be27c
7ee0: 00200200 00100100 bf0162f4 c000e544 dedf6000 00000000 00000000 bf010c00
7f00: bf0162cc bf00159c 00000000 df572980 df52e218 00000001 df5729b8 bf0031d0
[..]
[<c02ace88>] (usb_gadget_giveback_request) from [<c02adbbc>] (request_complete+0x64/0x88)
[<c02adbbc>] (request_complete) from [<c02aed3c>] (usba_ep_dequeue+0x70/0x128)
[<c02aed3c>] (usba_ep_dequeue) from [<bf010c00>] (hidg_unbind+0x50/0x7c [usb_f_hid])
[<bf010c00>] (hidg_unbind [usb_f_hid]) from [<bf00159c>] (remove_config.isra.6+0x98/0x9c [libcomposite])
[<bf00159c>] (remove_config.isra.6 [libcomposite]) from [<bf0031d0>] (__composite_unbind+0x34/0x98 [libcomposite])
[<bf0031d0>] (__composite_unbind [libcomposite]) from [<c02acee0>] (usb_gadget_remove_driver+0x50/0x78)
[<c02acee0>] (usb_gadget_remove_driver) from [<c02ad570>] (usb_gadget_unregister_driver+0x64/0x94)
[<c02ad570>] (usb_gadget_unregister_driver) from [<bf0160c0>] (hidg_cleanup+0x10/0x34 [g_hid])
[<bf0160c0>] (hidg_cleanup [g_hid]) from [<c0056748>] (SyS_delete_module+0x118/0x19c)
[<c0056748>] (SyS_delete_module) from [<c000e3c0>] (ret_fast_syscall+0x0/0x30)
Code: bad PC value
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
[nicolas.ferre@atmel.com: reworked the commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 914a3f3b37 ("USB: add atmel_usba_udc driver")
Cc: <stable@vger.kernel.org> # 2.6.x-ish
Signed-off-by: Felipe Balbi <balbi@ti.com>
We try to free an ERR_PTR on this error path.
Fixes: b44be2462d ('usb: gadget: gadgetfs: Free memory allocated by memdup_user()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 1290a958d4 ("usb: phy: propagate __of_usb_find_phy()'s error on
failure") actually broke the deferred probing mechanism, since it now returns
EPROBE_DEFER only when the try_module_get call fails, but not when the phy
lookup does.
All the other similar functions seem to return ENODEV when try_module_get
fails, and the error code of either __usb_find_phy or __of_usb_find_phy
otherwise.
In order to have a consistent behaviour, and a meaningful EPROBE_DEFER, always
return EPROBE_DEFER when __(of_)usb_find_phy fails to look up the requested
phy, that will be propagated by the caller, and ENODEV if try_module_get fails.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8dccddbc2368 ("OHCI: final fix for NVIDIA problems (I hope)")
introduced into 3.1.9 broke boot on e.g. Freescale P2020DS development
board. The code path that was previously specific to NVIDIA controllers
had then become taken for all chips.
However, the M5237 installed on the board wedges solid when accessing
its base+OHCI_FMINTERVAL register, making it impossible to boot any
kernel newer than 3.1.8 on this particular and apparently other similar
machines.
Don't readl() and writel() base+OHCI_FMINTERVAL on PCI ID 10b9:5237.
The patch is suitable for the -next tree as well as all maintained
kernels up to 3.2 inclusive.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org> # 3.2
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These platform_drivers do not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead rely on device tree information for ehci and ohci.
This was suggested with
http://www.linux-mips.org/cgi-bin/mesg.cgi?a=linux-mips&i=1401358203-60225-4-git-send-email-alex.smith%40imgtec.com
"The device tree will *always* have correct ehci/ohci clock
configuration, so use it. This allows us to remove a big chunk of
platform configuration code from octeon-platform.c."
More or less I rebased that patch on Alan's work to remove ehci-octeon
and ohci-octeon drivers.
Cc: David Daney <david.daney@cavium.com>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Rockchip rk3288 EHCI controller doesn't properly detect
the case when a device is removed during suspend. Specifically,
when usb resume from suspend, the EHCI controller maintaining
the USB state (FLAG_CF is 1, Current Connect Status is 1),
but a USB device (like a USB camera on rk3288) may have been
disconnected actually.
Let's add a quirk to force ehci to go into the
usb_root_hub_lost_power() path and reset after resume.
This should generally reset the whole controller and all
ports and initialize everything cleanly again, and bring
the devices back up.
As part of this, rename the "hibernation" paramter of
ehci_resume() to force_reset since hibernation is simply
another case where we can't trust the autodetected status
and need to force a reset of devices.
Signed-off-by: Wu Liang feng <wulf@rock-chips.com>
Reviewed-by: Julius Werner <jwerner@google.com>
Reviewed-by: Doug Anderson <dianders@google.com>
Reviewed-by: Tomasz Figa <tfiga@google.com>
Reviewed-by: Pawel Osciak <posciak@google.com>
Reviewed-by: Sonny Rao <sonnyrao@google.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Doug Anderson <dianders@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a %*ph specifier that allows to dump small buffers. This patch
converts the code to use the specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a %*ph specifier that allows to dump small buffers. This patch
converts the code to use the specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To be future-proof and for better readability the time comparisons are
modified to use time_after() instead of plain, error-prone math.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Acked-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the following error pops up during "testusb -a -t 10"
| musb-hdrc musb-hdrc.1.auto: dma_pool_free buffer-128, f134e000/be842000 (bad dma)
hcd_buffer_create() creates a few buffers, the smallest has 32 bytes of
size. ARCH_KMALLOC_MINALIGN is set to 64 bytes. This combo results in
hcd_buffer_alloc() returning memory which is 32 bytes aligned and it
might by identified by buffer_offset() as another buffer. This means the
buffer which is on a 32 byte boundary will not get freed, instead it
tries to free another buffer with the error message.
This patch fixes the issue by creating the smallest DMA buffer with the
size of ARCH_KMALLOC_MINALIGN (or 32 in case ARCH_KMALLOC_MINALIGN is
smaller). This might be 32, 64 or even 128 bytes. The next three pools
will have the size 128, 512 and 2048.
In case the smallest pool is 128 bytes then we have only three pools
instead of four (and zero the first entry in the array).
The last pool size is always 2048 bytes which is the assumed PAGE_SIZE /
2 of 4096. I doubt it makes sense to continue using PAGE_SIZE / 2 where
we would end up with 8KiB buffer in case we have 16KiB pages.
Instead I think it makes sense to have a common size(s) and extend them
if there is need to.
There is a BUILD_BUG_ON() now in case someone has a minalign of more than
128 bytes.
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Helps debugging to know the unhandled event type.
Also make the debug message grepable
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some parameters are not used by functions in xhci-mem.c, just
remove it.
Changes compared to v1:
- Rebase to the latest usb-next branch
Signed-off-by: Lin Wang <lin.x.wang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parameter 'xhci' is no longer be used in function xhci_handshake(),
just remove it.
Signed-off-by: Lin Wang <lin.x.wang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes unused variable "out_ctx" and avoid multiple calls
to function xhci_get_endpoint_flag().
Signed-off-by: Lin Wang <lin.x.wang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like all previous UAS capable Seagate disk enclosures, these need the
US_FL_NO_ATA_1X to not crash when udev probes them.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our detection logic to avoid doing UAS on ASM1051 bridge chips causes problems
with newer ASM1153 disk enclosures in 2 ways:
1) Some ASM1153 disk enclosures re-use the ASM1051 device-id of 5106, which
we assume is always an ASM1051, so remove the quirk for 5106, and instead
use the same detection logic as we already use for device-id 55aa, which is
used for all of ASM1051, ASM1053 and ASM1153 devices <sigh>.
2) Our detection logic to differentiate between ASM1051 and ASM1053 sees
ASM1153 devices as ASM1051 because they have 32 streams like ASM1051 devs.
Luckily the ASM1153 descriptors are not 100% identical, unlike the previous
models the ASM1153 has bMaxPower == 0, so use that to differentiate it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 1290a958d4 ("usb: phy: propagate __of_usb_find_phy()'s error on
failure") changed the condition to return -EPROBE_DEFER to host driver.
Originally the Tegra host driver depended on the returned -EPROBE_DEFER to
get the phy device later when booting. Now we have to do that explicitly.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Apricorn SATA dongle will occasionally return "USBSUSBSUSB" in
response to SCSI commands when running in UAS mode. Therefore,
disable UAS mode on this dongle.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the JMicron JMS567 enclosures with the JMS566 choke on report-opcodes,
so avoid it.
Tested-and-reported-by: Takeo Nakayama <javhera@gmx.com>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is yet another Seagate device which needs the US_FL_NO_ATA_1X quirk
Reported-by: Marcin Zajączkowski <mszpak@wp.pl>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams do not work reliabe on Fresco Logic FL1000G xhci controllers,
trying to use them results in errors like this:
21:37:33 kernel: xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring
21:37:33 kernel: xhci_hcd 0000:04:00.0: @00000000368b3570 9067b000 00000000 05000000 01078001
21:37:33 kernel: xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring
21:37:33 kernel: xhci_hcd 0000:04:00.0: @00000000368b3580 9067b400 00000000 05000000 01038001
As always I've ordered a pci-e addon card with a Fresco Logic controller for
myself to see if I can come up with a better fix then the big hammer, in
the mean time this will make uas devices work again (in usb-storage mode)
for FL1000G users.
Reported-by: Marcin Zajączkowski <mszpak@wp.pl>
Cc: stable@vger.kernel.org # 3.15
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB stack uses error code -ENOSPC to indicate that the periodic
schedule is too full, with insufficient bandwidth to accommodate a new
allocation. It uses -EFBIG to indicate that an isochronous transfer
could not be linked into the schedule because it would exceed the
number of isochronous packets the host controller driver can handle
(generally because the new transfer would extend too far into the
future).
ehci-hcd uses the wrong error code at one point. This patch fixes it,
along with a misleading comment and debugging message.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c3ee9b76aa (EHCI: improved logic for isochronous scheduling)
introduced the idea of using ehci->last_iso_frame as the origin (or
base) for the circular calculations involved in modifying the
isochronous schedule. However, the new code it added used
ehci->last_iso_frame before the value was properly initialized. This
patch rectifies the mistake by moving the initialization lines earlier
in iso_stream_schedule().
This fixes Bugzilla #72891.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: c3ee9b76aa
Reported-by: Joe Bryant <tenminjoe@yahoo.com>
Tested-by: Joe Bryant <tenminjoe@yahoo.com>
Tested-by: Martin Long <martin@longhome.co.uk>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Solves xhci error cases with debug messages:
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1.
usb 1-6: hub failed to enable device, error -22
xhci will give a context state error if we try to set a slot in default
state to the same default state with a special address device command.
Turns out this happends in several cases:
- retry reading the device rescriptor in hub_port_init()
- usb_reset_device() is called for a slot in default state
- in resume path, usb_port_resume() calls hub_port_init()
The default state is usually reached from most states with a reset device
command without any context state errors, but using the address device
command with BSA bit set (block set address) only works from the enabled
state and will otherwise cause context error.
solve this by checking if we are already in the default state before issuing
a address device BSA=1 command.
Fixes: 48fc7dbd52 ("usb: xhci: change enumeration scheme to 'new scheme'")
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 14b4099c07
It moved platform_set_drvdata(pdev, ci) before hcd is created,
and the hcd will assign itself as ci controller's drvdata during
the hcd creation function (in usb_create_shared_hcd), so it
overwrites the real ci's drvdata which we want to use.
So, if the controller is at host mode, the system suspend
API will get the wrong struct ci_hdrc pointer, and cause the
oops.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
As has been discussed in the thread starting with
https://lkml.kernel.org/g/549748e9.d+SiJzqu50f1r4lSAL043YSc@arcor.de
Sierra Wireless MC73xx devices with USB VID/PID 0x1199:0x68c0 require the
option_send_setup() code to be used on the USB interface for the AT port
to make unsolicited response codes work correctly. Move these devices from
the qcserial driver where they have been added by commit
70a3615fc0 ("usb: qcserial: add Sierra Wireless
MC73xx") to the option driver and add a MC73xx-specific blacklist
to ensure that
1. the sendsetup code is not used for the DIAG/DM and NMEA interfaces
2. the option driver does not attach to the QMI/network interfaces
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Added virtual com port VID/PID entries for CEL USB sticks and MeshWorks
devices.
Signed-off-by: David Peterson <david.peterson@cel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix null-pointer dereference during probe if the interface-status
completion handler is called before the individual ports have been set
up.
Fixes: f79b2d0fe8 ("USB: keyspan: fix NULL-pointer dereferences and
memory leaks")
Reported-by: Richard <richjunk@pacbell.net>
Tested-by: Richard <richjunk@pacbell.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixing typo for MeshConnect IDs. The original PID (0x8875) is not in
production and is not needed. Instead it has been changed to the
official production PID (0x8857).
Signed-off-by: Preston Fick <pffick@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Commit 1290a958d4 ("usb: phy: propagate __of_usb_find_phy()'s error on
failure") broke platforms that rely on deferred probing to order probing
of PHY and host controller drivers. The reason is that the commit simply
propagates errors from __of_usb_find_phy(), which returns -ENODEV if no
PHY has been registered yet for a given device tree node. The only case
in which -EPROBE_DEFER would now be returned is if try_module_get() did
fail, which does not make sense.
The correct thing to do is to return -EPROBE_DEFER if a PHY hasn't been
registered yet. The only condition under which it makes sense to return
-ENODEV is if the device tree node representing the PHY has been
disabled (via the status property) because in that case the PHY will
never be registered.
This patch addresses the problem by making __of_usb_find_phy() return an
appropriate error code while keeping in line with the above-mentioned
commit to propagate error codes rather than overwriting them. At the
same time the check for a valid PHY is decoupled from the check for the
try_module_get() call and a separate error code is returned if the
latter fails.
Fixes: 1290a95 (usb: phy: propagate __of_usb_find_phy()'s error on failure)
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When receive data, the RXRDY in status register set by hardware
after a new packet has been stored in the endpoint FIFO. When it
is copied from FIFO, this bit is cleared which make the FIFO can
be accessed again.
In the receive_data() function, this bit RXRDY has been cleared.
So, after the receive_data() function return, this bit should
not be cleared again, or else it may cause the accessing FIFO
corrupt, which will make the data loss.
Fixes: 914a3f3b37 (USB: add atmel_usba_udc driver)
Cc: <stable@vger.kernel.org> # 2.6.24+
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the datasheet, when transfer using DMA, the control
setting for IN packet only need END_BUF_EN, END_BUF_IE, CH_EN,
while for OUT packet, need more two bits END_TR_EN and END_TR_IE
to be configured.
Fixes: 914a3f3b37 (USB: add atmel_usba_udc driver)
Cc: <stable@vger.kernel.org> # 2.6.24+
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 3b74c73f8d switched over to memdup_user()
in ep_write() function and removed kfree (kbuf).
memdup_user() function allocates memory which is never freed.
Fixes: 3b74c73 (usb: gadget: inode: switch over to memdup_user())
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
since the split of host+gadget mode in commit 74c2e93600 ("usb: musb:
factor out hcd initalization") we leak the usb_hcd struct. We call now
musb_host_cleanup() which does basically usb_remove_hcd() and also sets
the hcd variable to NULL. Doing so makes the finall call to
musb_host_free() basically a nop and the usb_hcd remains around for ever
without anowner.
This patch drops that NULL assignment for that reason.
Fixes: 74c2e93600 ("usb: musb: factor out hcd initalization")
Cc: <stable@vger.kernel.org> # v3.11+
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This makes us sure that all requests are completed before we unbind
gadget. There are assumptions in gadget API that all requests have to
be completed and leak of complete can break some usb function drivers.
For example unbind of ECM function can cause NULL pointer dereference:
[ 26.396595] configfs-gadget gadget: unbind function
'cdc_ethernet'/e79c4c00
[ 26.414999] Unable to handle kernel NULL pointer dereference at
virtual address 00000000
(...)
[ 26.452223] PC is at ecm_unbind+0x6c/0x9c
[ 26.456209] LR is at ecm_unbind+0x68/0x9c
(...)
[ 26.603696] [<c033fdb4>] (ecm_unbind) from [<c033661c>]
(purge_configs_funcs+0x94/0xd8)
[ 26.611674] [<c033661c>] (purge_configs_funcs) from [<c0336674>]
(configfs_composite_unbind+0x14/0x34)
[ 26.620961] [<c0336674>] (configfs_composite_unbind) from
[<c0337124>] (usb_gadget_remove_driver+0x68/0x9c)
[ 26.630683] [<c0337124>] (usb_gadget_remove_driver) from [<c03376c8>]
(usb_gadget_unregister_driver+0x64/0x94)
[ 26.640664] [<c03376c8>] (usb_gadget_unregister_driver) from
[<c0336be8>] (unregister_gadget+0x20/0x3c)
[ 26.650038] [<c0336be8>] (unregister_gadget) from [<c0336c84>]
(gadget_dev_desc_UDC_store+0x80/0xb8)
[ 26.659152] [<c0336c84>] (gadget_dev_desc_UDC_store) from
[<c0335120>] (gadget_info_attr_store+0x1c/0x28)
[ 26.668703] [<c0335120>] (gadget_info_attr_store) from [<c012135c>]
(configfs_write_file+0xe8/0x148)
[ 26.677818] [<c012135c>] (configfs_write_file) from [<c00c8dd4>]
(vfs_write+0xb0/0x1a0)
[ 26.685801] [<c00c8dd4>] (vfs_write) from [<c00c91b8>]
(SyS_write+0x44/0x84)
[ 26.692834] [<c00c91b8>] (SyS_write) from [<c000e560>]
(ret_fast_syscall+0x0/0x30)
[ 26.700381] Code: e30409f8 e34c0069 eb07b88d e59430a8 (e5930000)
[ 26.706485] ---[ end trace f62a082b323838a2 ]---
It's because in some cases request is still running on endpoint during
unbind and kill_all_requests() called from s3c_hsotg_udc_stop() function
doesn't cause call of complete() of request. Missing complete() call
causes ecm->notify_req equals NULL in ecm_unbind() function, and this
is reason of this bug.
Similar breaks can be observed in another usb function drivers.
This patch fixes this bug forcing usb request completion in when
s3c_hsotg_ep_disable() is called from s3c_hsotg_udc_stop().
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace a misspelled function name by %s and then __func__.
This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 82c02f58ba ("usb: musb: Allow multiple glue layers to be
built in") enabled selecting multiple glue layers, which in turn
exposed things more for randconfig builds. If NOP_USB_XCEIV is
built-in and TUSB6010 is a loadable module, we will get:
drivers/built-in.o: In function `tusb_remove':
tusb6010.c:(.text+0x16a817): undefined reference to `usb_phy_generic_unregister'
drivers/built-in.o: In function `tusb_probe':
tusb6010.c:(.text+0x16b24e): undefined reference to `usb_phy_generic_register'
make: *** [vmlinux] Error 1
Let's fix this the same way as commit 70c1ff4b3c ("usb: musb:
tusb-dma can't be built-in if tusb is not").
And while at it, let's not allow selecting the glue layers except
on platforms really using them unless COMPILE_TEST is specified:
- TUSB6010 is in practise only used on omaps
- DSPS is only used on TI platforms
- UX500 is only used on STE platforms
Cc: Linus Walleij <linus.walleij@linaro.org>
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
!strncmp(buf, "force host", 9) is true if and only if buf starts with
"force hos". This was obviously not what was intended. The same error
exists for "force full-speed", "force high-speed" and "test
packet". Using strstarts avoids the error-prone hardcoding of the
prefix length.
For consistency, also change the other occurences of the !strncmp
idiom.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit cc92f681 (usb: musb: Populate new IO
functions for blackfin) added a typo which
prevented MUSB's blackfin glue layer from being
built. Due to lack of tests and compilers for
that architecture, the typo ended up being
merged and causing a build regression.
Fix that here
Cc: Tony Lindgren <tony@atomide.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Blackfin's MUSB implementation lacks a bunch of
registers which they end up not defining a macro
for. In order to avoid build breaks, let's ifdef
out some of the registers from our regdump debugfs
utility so that we don't try to use those on
Blackfin builds.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a much shorter set of patches that were on the go but didn't make it
in to the early pull request for the merge window. It's really a set of bug
fixes plus some final cleanup work on the new tag queue API.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJUlaYEAAoJEDeqqVYsXL0MmXAH/2UUcE11p0KBHMR4cAn76xrG
9093ZT9VZ4LH/Z7PbgwIWC4YHDqVpwA1+Trj1mh8PxiZz2SopWe27O2lQMRS5VUc
MN28kbmK3L0jQj+OUez10Da6k0hU/KL8TlWT765MxFDKCaAuPZ4u541tyZEIGmLL
olOQrn/fSlu+18QqqZ+D2rMaK7kGH6ZgbOadnRfYGkLjU4YeAMEC9L7UgnDxHiaN
gZozoARkGeAnDJERVETRTtAiOXGRH8sGCpue0yYlhZXpAQ9cFUkS/hMqDWnaVC2S
0x0w34RvbxSqO0gPT0K5XLoMiFyg04vnZ2xBVFBsANQTSEjQJO8USNAa4r74hf8=
=D3eN
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI update from James Bottomley:
"This is a much shorter set of patches that were on the go but didn't
make it in to the early pull request for the merge window. It's
really a set of bug fixes plus some final cleanup work on the new tag
queue API"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
storvsc: ring buffer failures may result in I/O freeze
ipr: set scsi_level correctly for disk arrays
ipr: add support for async scanning to speed up boot
scsi_debug: fix missing "break;" in SDEBUG_UA_CAPACITY_CHANGED case
scsi_debug: take sdebug_host_list_lock when changing capacity
scsi_debug: improve driver description in Kconfig
scsi_debug: fix compare and write errors
qla2xxx: fix race in handling rport deletion during recovery causes panic
scsi: blacklist RSOC for Microsoft iSCSI target devices
scsi: fix random memory corruption with scsi-mq + T10 PI
Revert "[SCSI] mpt3sas: Remove phys on topology change"
Revert "[SCSI] mpt2sas: Remove phys on topology change."
esas2r: Correct typos of "validate" in a comment
fc: FCP_PTA_SIMPLE is 0
ibmvfc: remove unused tag variable
scsi: remove MSG_*_TAG defines
scsi: remove scsi_set_tag_type
scsi: remove scsi_get_tag_type
scsi: never drop to untagged mode during queue ramp down
scsi: remove ->change_queue_type method
Having switched over all of the users of CONFIG_PM_RUNTIME to use
CONFIG_PM directly, turn the latter into a user-selectable option
and drop the former entirely from the tree.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci and
other individual USB driver updates. The PHY tree is also in here, as
there were dependancies on the USB tree.
All of these have been in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOEHcACgkQMUfUDdst+ykziQCgsm1D/af2nac6CTF2pov8VMIY
ywgAnRi8LtZ2WassrwTNxY86Avaqryis
=UVp8
-----END PGP SIGNATURE-----
Merge tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci
and other individual USB driver updates. The PHY tree is also in
here, as there were dependancies on the USB tree.
All of these have been in linux-next"
* tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (351 commits)
arm: omap3: twl: remove usb phy init data
usbip: fix error handling in stub_probe()
usb: gadget: udc: missing curly braces
USB: mos7720: delete some unneeded code
wusb: replace memset by memzero_explicit
usbip: remove unneeded structure
usb: xhci: fix comment for PORT_DEV_REMOVE
xhci: don't use the same variable for stopped and halted rings current TD
xhci: clear extra bits from slot context when setting max exit latency
xhci: cleanup finish_td function
USB: adutux: NULL dereferences on disconnect
usb: chipidea: fix platform_no_drv_owner.cocci warnings
usb: chipidea: Fixed a few typos in comments
Documentation: bindings: add doc for the USB2 ChipIdea USB driver
usb: chipidea: add a usb2 driver for ci13xxx
usb: chipidea: fix phy handling
usb: chipidea: remove duplicate dev_set_drvdata for host_start
usb: chipidea: parameter 'mode' isn't needed for hw_device_reset
usb: chipidea: add controller reset API
usb: chipidea: remove flag CI_HDRC_REQUIRE_TRANSCEIVER
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so Kconfig options
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace PM_RUNTIME with PM in Kconfig dependencies throughout the
tree.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tejun Heo <tj@kernel.org>
Pull HID updates from Jiri Kosina:
- i2c-hid race condition fix from Jean-Baptiste Maneyrol
- Logitech driver now supports vendor-specific HID++ protocol, allowing
us to deliver a full multitouch support on wider range of Logitech
touchpads. Written by Benjamin Tissoires
- MS Surface Pro 3 Type Cover support added by Alan Wu
- RMI touchpad support improvements from Andrew Duggan
- a lot of updates to Wacom driver from Jason Gerecke and Ping Cheng
- various small fixes all over the place
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (56 commits)
HID: rmi: The address of query8 must be calculated based on which query registers are present
HID: rmi: Check for additional ACM registers appended to F11 data report
HID: i2c-hid: prevent buffer overflow in early IRQ
HID: logitech-hidpp: disable io in probe error path
HID: logitech-hidpp: add boundary check for name retrieval
HID: logitech-hidpp: check name retrieval return code
HID: logitech-hidpp: do not return the name length
HID: wacom: Report input events for each finger on generic devices
HID: wacom: Initialize MT slots for generic devices at post_parse_hid
HID: wacom: Update maximum X/Y accounding to outbound offset
HID: wacom: Add support for DTU-1031X
HID: wacom: add defines for new Cintiq and DTU outbound tracking
HID: wacom: fix freeze on open when autosuspend is on
HID: wacom: re-add accidentally dropped Lenovo PID
HID: make hid_report_len as a static inline function in hid.h
HID: wacom: Consult the application usage when determining field type
HID: wacom: PAD is independent with pen/touch
HID: multitouch: Add quirk for VTL touch panels
HID: i2c-hid: fix race condition reading reports
HID: wacom: Add angular resolution data to some ABS axes
...
Pull networking updates from David Miller:
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
Conflicts:
drivers/scsi/scsi_debug.c
Agreed and tested resolution to a merge problem between a fix in scsi_debug
and a driver update
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For SPI drivers use the message definitions from scsi.h, and for target
drivers introduce a new TCM_*_TAG namespace.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM (or even dropped in some cases).
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the USB core code
and documentation.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If usb_hub_claim_port() fails, no resources are deallocated and
if stub_add_files() fails, port is not released.
The patch fixes these issues and rearranges error handling code.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Valentina Manea <valentina.manea.m@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There were curly braces intended here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "status" is uninitialized so this creates a static checker warning.
But it's harmless, we can just delete it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memset on a local variable may be removed when it is called just before the
variable goes out of scope. Using memzero_explicit defeats this
optimization. A simplified version of the semantic patch that makes this
change is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier x;
type T;
@@
{
... when any
T x[...];
... when any
when exists
- memset
+ memzero_explicit
(x,
-0,
...)
... when != x
when strict
}
// </smpl>
This change was suggested by Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to xHCI specification, PORT_DEV_REMOVE(bit 30) in PORTSC
true means "Device is non-removable".
Reported-by: Juro Bystricky <jurobystricky@hotmail.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Endpoints halted on errors, and endpoints stopped manually both used
the same ep->stopped_td to store the halted or stopped td. this causes
confusion and possible races.
There is no longer a need to use the ep->stopped_td variable to store
the halted TD. A halted endpoint is handled immediately and we can pass
it to the handling function directly.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we need to change the max exit latency with a Evaluate Context
command, we copy the old output slot context and use it as input
context for the command. This also copies the dev_state bits which
are supposed to be zero in the input slot context.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of non-dt boot. Adds three new PHY drivers using the PHY framework and some
miscellaneous fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=oo3u
-----END PGP SIGNATURE-----
Merge tag 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-testing
Kishon writes:
Improvements in phy-core specifically on PHY core finds the PHY in the case
of non-dt boot. Adds three new PHY drivers using the PHY framework and some
miscellaneous fixes and cleanups.
Both "dev->udev" and "interface->dev" are NULL. These printks are not
very interesting so I just deleted them.
Fixes: 03270634e2 ('USB: Add ADU support for Ontrak ADU devices')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/chipidea/ci_hdrc_usb2.c:108:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Cc: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These changes add a new "simple" driver for Google USB-serial
devices and add support for Huawei Gobi modems to qcserial.
Included are also some removals of unnecessary atomic allocations and
a few spelling fixes.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=m/eD
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v3.19-rc1
These changes add a new "simple" driver for Google USB-serial
devices and add support for Huawei Gobi modems to qcserial.
Included are also some removals of unnecessary atomic allocations and
a few spelling fixes.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixed typos in comments of 2 drivers/usb/chipidea files
Signed-off-by: Mickael Maison <mickael.maison@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a USB2 ChipIdea driver for ci13xxx, with optional PHY, clock
and DMA mask, to support USB2 ChipIdea controllers that don't need
specific functions.
Tested on the Marvell Berlin SoCs USB controllers.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generic plaftorm device for ChipIdea drivers is probed by calling
ci_hdrc_probe. The device structure used is not the one of the specific
ChipIdea driver but the one of the generic ChipIdea platform device.
This results in not being able to probe the PHYs as we're not using the
right device structure. Since all ChipIdea drivers are retrieving their
PHYs in their specific driver code, this didn't impact any of them yet.
Fixes it using the right device structure (dev->parent).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The core driver has already done it, besides, move set driver data
operation just after ci has allocated successfully in case some
code (like ci_role_start) want to access this driver data.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hw_device_reset is dedicated to be used at device mode initializaiton,
so delete the parameter 'mode'. For host driver, the ehci driver will
handle all things.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add controller reset API, currently it is used for device mode only.
It may be used for host/otg driver in future.
Ususally, we need this API for dual-role switch and back from hibernation
suspend to let the controller at default state.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, USB PHY is mandatory for chipidea core, the flag
CI_HDRC_REQUIRE_TRANSCEIVER is useless.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add basic system power management support
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add system power management support
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The phy needs some delay to output the stable status from low
power mode. And for OTGSC, the status inputs are debounced
using a 1 ms time constant, so, delay 2ms for controller to get
the stable status(like vbus and id) when the phy leaves low power.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The individual PHY driver should take this responsibility if it
needs to delay between clear portsc.phcd and let the phy leave
low power mode.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to do an intermediate step for reading the
MX53_USB_OTG_PHY_CTRL_1_OFFSET register.
Read it directly instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If 'evdo' property is not defined, then reading the MX25_USB_PHY_CTRL_OFFSET
register is an unneeded operation.
Move the reading of MX25_USB_PHY_CTRL_OFFSET inside the 'evdo' if block code,
where it is actually used.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MM core code already complains when devm_kzalloc() fails, so no need to print
the error locally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MM core code already complains when devm_kzalloc() fails, so no need to print
the error locally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using devm_request_irq to instead of request_irq.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WYyZ
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.19 merge window
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove special-purpose octeon drivers and instead use ehci-platform
and ohci-platform as suggested with
http://marc.info/?l=linux-mips&m=140139694721623&w=2
[andreas.herrmann:
fixed compile error]
Cc: David Daney <david.daney@cavium.com>
Cc: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This removes the ifdef clutter a bit and saves few lines.
It also makes it easier to detect the remaining places
where we have conditional building of code done based
on if defined for things like DMA.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There's no reason any longer to keep it as a choice now that
the IO access has been fixed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This allows the endpoints to work when multiple MUSB glue
layers are built in.
Cc: Fabio Baltieri <fabio.baltieri@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Change to use new IO access. This allows us to build in multiple
MUSB glue layers.
[ balbi@ti.com : switch to EXPORT_SYMBOL_GPL()
fix long lines ]
Cc: Fabio Baltieri <fabio.baltieri@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Populate new IO functions for blackfin
Cc: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Let's populate the new IO functions for tusb6010 but not use
them yet.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
MUSB currently breaks badly if we try to build in support
for multiple platforms. This also happens if done as loadable
modules, which is not nice for distros.
Let's fix the issue by adding new struct musb_io for the IO
access functions that the platform code can populate. Note
that we don't want to use the current ops as that's really
platform_data and and set as a const.
This should allow eventually adding function pointers also
for the DMA code to struct musb_io, but that's a whole
different set of patches. For now, let's just fix the PIO
access.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When usb is connected and enumerated in device mode or when
usb is disconnected, call usb_phy_set_event() from phy drivers
to handle per-PHY event.
[ toddpoynor@google.com : Original patch in Android ]
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: Android Kernel Team <kernel-team@android.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Benoit Goby <benoit@android.com>
Cc: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Kiran Raparthy <kiran.kumar@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since we have assigned clk=NULL, which is a valid clk, we should not
be returning when a clock node is not provide. Instead, we should return
only when we cannot enable the clock.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sergei Shtylyov