Control arrays as are used with v4l2_ctrl_next must be sorted from
low to high. Add a comment at the top of all such arrays to warn
about this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
KBL is not needed on saa7134, so, let's remove it.
However, we should take some care to avoid opening the module while
initializing it. This issue exists with newer udev's that opens a device
as soon as the driver is registered. So, a proper lock is needed on
open.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix two broken controls where a step weren't specified. Without a step,
userspace apps won't allow to adjust such controls.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some saa7134 devices require to open an i2c gate before tuning. This
patch fix the initialization for those devices.
The nxt200x_gate_ctrl() logic were returned back to the old place, since
we don't know how to close the gate. A future pacth could revert that
change and provide the proper close gate control, to avoid keeping it
open forever.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On certain devices, before opening a tuner, we need to open the tuner
gate via i2c.
This patch just moves the tuner probing code to the same place where
such i2c commands are handled, to make easier to fix this trouble on
later patches.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Most boards nowadays supports saa7134-alsa. Even some of they doesn't have any
option to wire an audio cable. So, lets load saa7134-alsa by default, if the
board is not based on saa7130 and if saa7134-alsa is compiled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
saa7134: Fix tuner access on Kworld ATSC110
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add v4l2_i2c_tuner_addrs() to obtain the various I2C tuner addresses.
This will be used in several drivers, so make this a common function
as we do not want to have these I2C addresses all over the place.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register v4l2_device and switch to v4l2_subdev to access the i2c modules.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
zl10353 i2c-gate was always closed and due to that devices having tuner
behind i2c-gate were broken. Add module configuration which allows disabling
i2c-gate only when really needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According with saa7130 public datasheet, saa7130 doesn't support
digital audio. This is also confirmed by experimental tests. So, it
doesn't make sense to let saa7134-alsa register for those chipsets.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When enabling a shared IRQ line, then saa7134_irq handler could be invoked
before the driver had completely set up internal structures, due to a shared
interrupt line firing. Clear the saa7134 interrupt status reg, before
requesting the irq line, so that stale IRQ status isn't processed before the
internal structures are set up.
Marcin Slusarz recently brought this Oops to the attention of the v4l-dvb
lists and provided an initial analysis by investigating reports found here:
http://kerneloops.org/guilty.php?guilty=mute_input_7133&version=2.6.27-release&start=1802240&end=1835007&class=oops
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes autodetection for Avermedia AVerTV GO 007 FM Plus (M15C)
(PCI ID 1461:f31d).
Signed-off-by: Pham Thanh Nam <phamthanhnam.ptn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for Avermedia AVer TV GO 007 FM Plus (M15C) on
saa7134 driver (PCI ID 1461:f31d).
Signed-off-by: Pham Thanh Nam <phamthanhnam.ptn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the i2c driver ID will be removed in the near future we have to
modify the v4l2 debugging API to use the driver name instead of driver ID.
Note that this API is not used in applications other than v4l2-dbg.cpp
as it is for debugging and testing only.
Should anyone use the old VIDIOC_G_CHIP_IDENT, then this will be logged
with a warning that it is deprecated and will be removed in 2.6.30.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce a struct v4l2_file_operations for v4l2 drivers.
Remove the unnecessary inode argument.
Move compat32 handling (and llseek) into the v4l2-dev core: this is now
handled in the v4l2 core and no longer in the drivers themselves.
Note that this changeset reverts an earlier patch that changed the return
type of__video_ioctl2 from int to long. This change will be reinstated
later in a much improved version.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
How to enable the mpeg encoder is not found yet.
The card comes up with gpio 0x0820000 for DVB-T.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this
development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ARRAY_SIZE is more concise to use when the size of an array is divided by
the size of its type or the size of its first element.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@i@
@@
@depends on i using "paren.iso"@
type T;
T[] E;
@@
- (sizeof(E)/sizeof(E[...]))
+ ARRAY_SIZE(E)
@depends on i using "paren.iso"@
type T;
T[] E;
@@
- (sizeof(E)/sizeof(T))
+ ARRAY_SIZE(E)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This cleans-up MFE attachment for saa-7134 dvb
devices.
note: MFE is not fully implemented here yet.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The SAA7134 device driver currently only supports 8 such devices in a
system. This is too small for many surveillance applications. This
patch increases the number to 32.
Signed-off-by: Alan McIvor <alan.mcivor@reveal.co.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the tuner modules were moved to common/tuners, a separate customize
option were added for tuners. However, the automatic selection of the
tuners were still using the older option.
This causes that the automatic selection to fail, if DVB_FE_CUSTOMISE is
selected. Also, since those tuners are now under MEDIA_TUNER_CUSTOMIZE
menu, if you unset MEDIA_TUNER_CUSTOMIZE, you can't manually select the
tuners.
This patch fixes this error by replacing DVB_FE_CUSTOMISE by
MEDIA_TUNER_CUSTOMIZE on all places were a tuner is selected.
The patch were generated by this small script:
for i in `find drivers/media -name Kconfig`; do
cat $i|perl -ne 's/(MEDIA_TUNER.*)DVB_FE_CUSTOMISE/\1MEDIA_TUNER_CUSTOMIZE/; print $_' >a
mv a $i
done
Also, manually reordered the tuner entries.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Impact: driver could possibly stomp on resources outside of its scope
{mchehab@redhat.com: I got two versions of the same patch (identical,
except for whitespacing). One authored by Andy Burns and another
authored by Suresh Siddha. Due to that, I'm applying the one that has
less CodingStyle errors. I'm also adding both comments and the SOB's for
both patches, since they are both interesting}
Suresh Siddha commented:
Alexey Fisher reported:
> resource map sanity check conflict: 0xcfeff800 0xcff007ff 0xcfe00000
> 0xcfefffff PCI Bus 0000:01
BAR base is located in the middle of the 4K page and the hardcoded
size argument makes the request span two pages causing the conflict.
Fix the hard coded size argument in ioremap().
Andy Burns commented:
I have already sent this patch on the linux-dvb list, but it didn't get
much attention, so re-sending direct, I hope you all don't mind.
While attempting to run mythtv in a xen domU, I encountered problems
loading the driver for my saa7134 card, with an error from ioremap().
This error was due to the driver allocating an incorrectly sized mmio
area, which was trapped by xen's permission checks, but this would go
un-noticed on a kernel without xen.
My card has a 1K sized mmio area, I've had information that other cards
have 2K areas, perhaps others have different sizes, yet the driver
always attempts to map 4K. I realise that the granularity of mapping is
the page size, which typically would be 4K, but unless the card's base
address happens to fall on a 4K boundary (mine does not) then the
base+4K will end up spanning two pages, and this is when the error
occurs under xen.
My patch uses the pci_resource_len macro to determine the size required
for the user's particular card, instead of the hardcoded 4K value. I've
tested with a couple of printk() inside ioremap() that the start address
and size do get rounded to the closest page boundary.
With this patch I am able to successfully load the saa7134 driver and
run mythtv under xen with my card, subject to correct pollirq settings
in case of shared IRQ, I am still seeing occasional DMA panics, which I
think are related to swiotlb handling by dom0/domU, usually the panic
occurs when changing mux, once tuned to a mux, 12 hour continuous
recordings are possible without errors.
Reported-by: Alexey Fisher <bug-track@fisher-privat.net>
Tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andy Burns <andy@burns.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The kernel number of a v4l2 node (e.g. videoX, radioX or vbiX) is now
independent of the minor number. So instead of using the minor field
of the video_device struct one has to use the num field: this always
contains the kernel number of the device node.
I forgot about this when I did the v4l2 core change, so this patch
converts all drivers that use it in one go. Luckily the change is
trivial.
Cc: michael@mihu.de
Cc: mchehab@infradead.org
Cc: corbet@lwn.net
Cc: luca.risolia@studio.unibo.it
Cc: isely@pobox.com
Cc: pe1rxq@amsat.org
Cc: royale@zerezo.com
Cc: mkrufky@linuxtv.org
Cc: stoth@linuxtv.org
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To optimise data storage even further one other redundant
var has been removed.
This also removes a redundant assignment.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To optimise data storage redundant vars are removed.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This add frontend R/W mutual exclusion.
Prior to this point in time it was possible to open both
frontends simultaneously which an MFE card cannot support.
In order to stop this, a delayed open is performed which
has the following function:
- Return EBUSY after a configurable amount of time
if a frontend is unavailable due to the other being
in use.
- Only allow opening of a frontend if the kernel thread
of the other has stopped.
This solution was chosen to allow switching between
frontends to work as seamlessly as possible. When both
frontends are actually opened simultaneously then one
will only open, but if quick switching is performed
between one of many then the new open will succeed in
a clean fashion rather than interrupting a kernel
thread.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When using MFE on a setup with both and HVR-3000 and ASUS P7131
card it was noticed that frontend allocation for saa7134
adapters was missing. This patch adds that allocation for
both saa7134 and cx23885 adapters.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A number of reference to videobuf_dvb_get_frontend used an invalid
index. This has been fixed.
The section for the HVR3000 in advise_acquire was redundant as
the same logic is used on the HVR4000. This has been removed
and both cards now use the same function.
A number of small errors and whitespace errors are also fixed.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A detailed description from the original patches 2 years ago:
"The WinTV-HVR3000 has a single transport bus which is shared between
a DVB-T and DVB-S modulator. These patches build on the bus acquisition
cx88 work from a few weeks ago to add support for this.
So to applications the HVR3000 looks like this:
/dev/dvb/adapter0/fe0 (cx24123 DVB-S demod)
/dev/dvb/adapter0/fe1 (cx22702 DVB-T demod)
Additional boards continue as before, eg:
/dev/dvb/adapter1/fe0 (lgdt3302 ATSC demod)
The basic change is removing the single instance of the videobuf_dvb in
cx8802_dev and saa7134_dev(?) and replacing it with a list and some
supporting functions.
*NOTE* This branch was taken before v4l-dvb was closed for 2.6.19 so
two or three current cx88 patches appear to be reversed by this tree,
this will be cleaned up in the near future. The patches missing change
the mutex handing to core->lock, fix an enumeration problem."
It should be recognised that a number of people have been maintaining
this patchset. Significant levels of Kudos to everyone one involved,
including but not limited to:
Darron Broad
Fabio M. Di Nitto
Carlo Scarfoglio
Hans Werner
Without the work of these people, and countless others, my two year old
patches would of died on the Mercurial linuxtv.org vine a long time
ago.
TODO: Revise these patches a little further so that the need for
demux1 and dvr0 is optional, not mandatory on the HVR3000.
HISTORY (darron):
This is the last update to MFE prepared by Hans which is based
upon the `scratchpad' diff created by Carlo.
All MFE work prior to that point must be attributed to Fabio
who ported and maintained Steve's original patch up to that
time.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The IR controller has a couple quirks. It won't respond until some other
device on the bus is probed. To work around that, probe 0x50 first.
Then, since it won't respond to a zero-byte read, probe with a one-byte
read.
Signed-off-by: Brian Rogers <brian_rogers@comcast.net>
[mchehab.redhat.com: Fix merge conflicts and remove an unused var]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the vidioc_enum_fmt_vbi_cap ops: it was scheduled for removal in
2.6.28 since the v4l2 specification says that V4L2_BUF_TYPE_VBI_CAPTURE should
not support VIDIOC_ENUM_FMT. It's also pretty pointless.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In opposite to the P7131 Dual this early OEM card has a male
radio antenna connector and also no remote.
We currently switch the DVB-T RF feed to the radio input, like
on the P7131 with female radio connector used also for DVB-T
and should improve this.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is patch for solve this regression. Load ir-kbd-i2c module when remote is i2c type.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add PCI ID and device specific tables for ADS Tech Instant HDTV.
[mchehab@redhat.com: make checkpatch happy and fix merge conflicts]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The audio switch is at 0x100 and radio on gpio 21.
Tested-by: Thomas Genty <tomlohave@gmail.com>
Signed-off-by: David Bentham <db260179@hotmail.com>
Reviewed-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil