The iTCO_wdt driver erroneously releases the pci_dev, and causes PCI hotremove
to fail because of an incorrect usage count.
The probe for this driver does a for_each_pci_dev() which gets a reference for
a pci_dev when iTCO_wdt_init() is successful. The for_each_pci_dev() loop
puts a reference for a pci_dev when iTCO_wdt_init() fails, so the
iTCO_wdt_init() does not need to do any pci_dev_put()'s.
The only pci_dev_put() that is required is in the iTCO_wdt_cleanup() function.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds support for the Broadcom BCM63xx SoC built-in watchdog, it
uses one of the BCM63xx hardware timer id.
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On iEi PCISA-9652-R10 (BIOS version 1.5) single board computer reads
from the game port do not seem to reset the watchdog timer. This patch
adds a module parameter wdt_config_reg to specify alternative reset
sources. At least WDT_RESET_KBD has been tested, even just running
while true; do
setleds -L +scroll
sleep 1
setleds -L -scroll
sleep 1
done
is enough to keep the watchdog happy.
Signed-off-by: Timo Juhani Lindfors <timo.lindfors@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds support for watchdogs with 8b timers, like ones in
IT8702F and older revisions of IT8712F Super IO chip, to it87_wdt
driver. This patch should be used after the patch
'it87_wdt: Add support for IT8720F watchdog'.
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This simple patch adds support for a watchdog in IT8720F Super IO chip
to it87_wdt driver.
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The current iTCO_wdt driver warnings are confusing. Currently when the device
driver returns an error the console contains:
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: failed to reset NO_REBOOT flag, reboot disabled by hardware
iTCO_wdt: No card detected
After the patch,
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: failed to reset NO_REBOOT flag, device disabled by hardware/BIOS
Clean this up and use the word "device" to describe the device.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the Intel Patsburg (PCH) DeviceIDs for iTCO Watchdog.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
block: autoconvert trivial BKL users to private mutex
drivers: autoconvert trivial BKL users to private mutex
ipmi: autoconvert trivial BKL users to private mutex
mac: autoconvert trivial BKL users to private mutex
mtd: autoconvert trivial BKL users to private mutex
scsi: autoconvert trivial BKL users to private mutex
Fix up trivial conflicts (due to addition of private mutex right next to
deletion of a version string) in drivers/char/pcmcia/cm40[04]0_cs.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (71 commits)
powerpc/44x: Update ppc44x_defconfig
powerpc/watchdog: Make default timeout for Book-E watchdog a Kconfig option
fsl_rio: Add comments for sRIO registers.
powerpc/fsl-booke: Add e55xx (64-bit) smp defconfig
powerpc/fsl-booke: Add p5020 DS board support
powerpc/fsl-booke64: Use TLB CAMs to cover linear mapping on FSL 64-bit chips
powerpc/fsl-booke: Add support for FSL Arch v1.0 MMU in setup_page_sizes
powerpc/fsl-booke: Add support for FSL 64-bit e5500 core
powerpc/85xx: add cache-sram support
powerpc/85xx: add ngPIXIS FPGA device tree node to the P1022DS board
powerpc: Fix compile error with paca code on ppc64e
powerpc/fsl-booke: Add p3041 DS board support
oprofile/fsl emb: Don't set MSR[PMM] until after clearing the interrupt.
powerpc/fsl-booke: Add PCI device ids for P2040/P3041/P5010/P5020 QoirQ chips
powerpc/mpc8xxx_gpio: Add support for 'qoriq-gpio' controllers
powerpc/fsl_booke: Add support to boot from core other than 0
powerpc/p1022: Add probing for individual DMA channels
powerpc/fsl_soc: Search all global-utilities nodes for rstccr
powerpc: Fix invalid page flags in create TLB CAM path for PTE_64BIT
powerpc/mpc83xx: Support for MPC8308 P1M board
...
Fix up conflict with the generic irq_work changes in arch/powerpc/kernel/time.c
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
The PowerPC Book-E watchdog driver (booke_wdt.c) defines a default timeout
value in the code based on whether it's a Freescale Book-E part of not.
Instead of having hard-coded values in the driver, make it a Kconfig
option.
As newer chips gets faster, the current default values become less
appropriate, since the timeout sometimes occurs before the kernel finishes
booting. Making the value a Kconfig option allows BSPs to configure a new
value without requiring the wdt_period command-line parameter to be set.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Register the __init and __exit functions in the PowerPC Book-E Watchdog
driver as module entry/exit functions, and modify the Kconfig entry.
Add a .release method for the PowerPC Book-E Watchdog driver, so that the
watchdog is disabled when the driver is closed.
Loosely based on original code from Jiang Yutang <b14898@freescale.com>.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add missing #inclusions of <linux/irq.h> to a whole bunch of files that should
really include it. Note that this can replace #inclusions of <asm/irq.h>.
This is required for the patch to sort out irqflags handling function naming to
compile on MIPS.
The problem is that these files require access to things like setup_irq() -
which isn't available by #including <linux/interrupt.h>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.
None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.
Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.
These drivers do not seem to be under active
maintainance from my brief investigation. Apologies
to those maintainers that I have missed.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Call runtime pm APIs pm_runtime_put_sync() and pm_runtime_get_sync()
for enabling/disabling the clocks, sysconfig settings instead of using
clock FW APIs.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The NXP LPC32XX processor use the same watchdog as the Philips
PNX4008 processor.
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Since it may be already enabled by bootloader or some other utility. This patch
makes sure that the watchdog is disabled before any userspace daemon opens the
device. It is also required by the watchdog API.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
irq and reboot notifier are acquired in module_init() but never released.
They should be released correctly, otherwise reloading the module or error
during module_init() will cause a problem.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Andrew Sharp <andy.sharp@lsi.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
hpwdt is quite functional without the NMI decoding feature.
This change lets users disable the NMI portion at compile-time
via the new HPWDT_NMI_DECODING config option.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Move NMI-decoding initialisation and exit code to seperate functions so that
we can ifdef-out parts of it in the future.
Also, this is for a device, so let's use dev_info instead of printk.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The term "decoding" more clearly explains what hpwdt is doing. It isn't
just finding the source of the interrupt, but rather aids in decoding what
the interrupt means.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Reorganize this function to remove excess indentation and highlight
the single return code. (No functional change).
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Let applications check the amount of time left before the watchdog will fire.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The hpwdt timer is a 16 bit value with 128ms resolution.
Let applications use this entire range.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Define a macro to convert from seconds to timer ticks.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The 32-bit assembly is guarded by an #ifndef CONFIG_X86_64. Kconfig prevents
us from building this driver on !X86, so that happens to suffice - but we
should really lock it down to #ifdef CONFIG_X86_32.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This driver supports both iLO2 and iLO3, but our user-visible strings
currently only reference iLO2. Let's just call it "iLO2+" to avoid having
to update strings for each iLO generation. This driver doesn't support
iLO ASICs prior to iLO2, but that is sufficiently explained in Kconfig.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* Group together includes specific to NMI sourcing
* Group defines only used by NMI sourcing together
* Group declarations specific to NMI sourcing together
This gives a clean seperation of watchdog specific items and
NMI sourcing specific items (which is needed for making it
possible to build hpwdt without the NMI functionality).
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Reorganization only.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* remove unnecessary includes
* We use a spinlock, but lacked the include
* We need bitops.h for test_and_set_bit/clear_bit
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a new watchdog driver for the Fintek F71808E and F71882FG Super I/O
controllers.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Set the paranet of the misc_device before we register the misc_device.
Reported-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Wim Van sebroeck <wim@iguana.be>
Move the VENDOR/DEVICE ids to pci_ids.h.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
When removing the watchdog platform device, we need to
disable the access to userspace first. It makes no sense
to remove the drivers clock, irq's, ... and then disable
userspace access.
the order of removal has also been changed so that it
is the reverse of probing (this way the clock is also
disabled sooner).
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (63 commits)
of/platform: Register of_platform_drivers with an "of:" prefix
of/address: Clean up function declarations
of/spi: call of_register_spi_devices() from spi core code
of: Provide default of_node_to_nid() implementation.
of/device: Make of_device_make_bus_id() usable by other code.
of/irq: Fix endian issues in parsing interrupt specifiers
of: Fix phandle endian issues
of/flattree: fix of_flat_dt_is_compatible() to match the full compatible string
of: remove of_default_bus_ids
of: make of_find_device_by_node generic
microblaze: remove references to of_device and to_of_device
sparc: remove references to of_device and to_of_device
powerpc: remove references to of_device and to_of_device
of/device: Replace of_device with platform_device in includes and core code
of/device: Protect against binding of_platform_drivers to non-OF devices
of: remove asm/of_device.h
of: remove asm/of_platform.h
of/platform: remove all of_bus_type and of_platform_bus_type references
of: Merge of_platform_bus_type with platform_bus_type
drivercore/of: Add OF style matching to platform bus
...
Fix up trivial conflicts in arch/microblaze/kernel/Makefile due to just
some obj-y removals by the devicetree branch, while the microblaze
updates added a new file.
The OCTEON is a MIPS64 based SOC family with an on chip watchdog unit.
The driver is split into two source files one for the C code and one
for assembly. Assembly is needed to handle the NMI and then print the
machine state before the reboot is triggered.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Marc Zyngier <maz@misterjones.org>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
To: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org,
Patchwork: https://patchwork.linux-mips.org/patch/1503/
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 drivers/watchdog/octeon-wdt-main.c
create mode 100644 drivers/watchdog/octeon-wdt-nmi.S
Both of_bus_type and of_platform_bus_type are just #define aliases
for the platform bus. This patch removes all references to them and
switches to the of_register_platform_driver()/of_unregister_platform_driver()
API for registering.
Subsequent patches will convert each user of of_register_platform_driver()
into plain platform_drivers without the of_platform_driver shim. At which
point the of_register_platform_driver()/of_unregister_platform_driver()
functions can be removed.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
This patch moves SPARC architecture specific data members out of
struct of_device and into the pdev_archdata structure. The reason
for this change is to unify the struct of_device definition amongst
all the architectures. It also remvoes the .sysdata, .slot, .portid
and .clock_freq properties because they aren't actually used by
anything.
A subsequent patch will replace struct of_device entirely with struct
platform_device and the of_platform support code will share common
routines with the platform bus (but the bus instances themselves can
remain separate).
This patch also adds 'struct resources *resource' and num_resources
to match the fields defined in struct platform_device. After this
change, 'struct platform_device' can be used as a drop-in replacement
for 'struct of_platform'.
This change is in preparation for merging the of_platform_bus_type
with the platform_bus_type.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
This patch reworks the probe() function in the at32ap700x_wdt driver, this to
make sure the miscdev is properly initialized and the driver is ready to be
accessed.
Reported-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Wim Van sebroeck <wim@iguana.be>
At the point of the call to dev_err, wm8350 is NULL.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E,E1;
identifier f;
statement S1,S2,S3;
@@
if ((E == NULL && ...) || ...)
{
... when != if (...) S1 else S2
when != E = E1
* E->f
... when any
return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fixes build error caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 61c7a080a5 ( of: Always use
'struct device.of_node' to get device node pointer.) missed
drivers/watchdog/mpc8xxx_wdt.c. This patch fixes it
Signed-off-by: Michael Guntsche <mike@it-loops.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The rdc321x southbridge PCI device has no MEM PCI resources that we could
pass to mfd_add_devices. Since 33254dd5, mfd_add_device checks for the
mem_base argument that we set to NULL. Changing the resources passed to
our MFD cells from IORESOURCE_MEM to IORESOURCE_IO fixes that. Since we use
those resources as offsets to the PCI configuration space base address of
the southbridge device this is also more adequate.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The RDC321x MFD southbridge driver will pass a reference to the
southbridge PCI device which should be used by the watchdog driver for its
operations. This patch converts the watchdog driver to use the pci_dev
pointer and make use of the base register resource which is passed along
with the platform device.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is the driver for the hardware watchdog on the Freescale IMX2 and later processors.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is a long overdue driver model conversion for the shwdt watchdog
driver. This is the initial conversion, more incremental changes to
follow.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If the request for wdt_mem region fails, this patch modifies the driver
such that, it does not try to release the wdt_mem region on exit.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds HAVE_S3C2410_WATCHDOG to control inclusion of watchdog driver
for Samsung SoCs. This option will help to include the driver only for the
necessary machines and not for all for any given arch.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
For TCO V1 devices the programmed timeout was twice too long
because the fact that the TCO V1 timer needs to count down
twice before triggering the watchdog, wasn't accounted for.
Also the timeout values in the module description and error
message were clarified. And the _STS registers are 16 bit
instead of 8 bit.
Signed-off-by: Pádraig Brady <P@draigBrady.com>
Tested-by: Simon Kagstrom <simon.kagstrom@netinsight.se>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If we are not able to register then it is better to have
watchdog in disabled state than noticing a system reboot.
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Acked-By: Timo Kokkonen <timo.t.kokkonen@nokia.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Move the limited watchdog driver help from kernel-parameters.txt
to Documentation/watchdog/watchdog-parameters.txt and add info to it
for all watchdog drivers except the ones that have driver-specific
files already.
Correct minor comments and MODULE_PARM_DESC() text in 2 places.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix MODULE_PARM_DESC() strings in several watchdog drivers.
Some are simple as add a parenthesis.
Others are problems from __stringify() being used on a
variable name instead of a macro name, so the variable name
is produced in the string instead of its build-time value.
In these cases, create a macro for the value so that the
module param description string is useful.
Only pc87413_wdt has been built (due to toolchains).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The wdt mmaping thing was a special-cased hack that nothing in the wild
depends on, so just kill it off. While at it, sanitize the superfluous
comments in preparation for a driver rewrite and overhauled interface.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This fixes the build failures seen when building mpcore_wdt and it
also removes the nonexistent ARM_MPCORE_PLATFORM dependency, instead
make it dependent on HAVE_ARM_TWD.
Also this fixes spinlock usage appropriately.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The WATCHDOG_TIMEOUT macro does not exist. The default timeout value is WDT_TIMEOUT.
Fix the MODULE_PARM_DESC so that the code can compile again.
reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
commit 42747d712d ("[WATCHDOG] watchdog_info
constify") introduced the following build failure:
CC booke_wdt.o
booke_wdt.c: In function 'booke_wdt_init':
booke_wdt.c:220: error: assignment of read-only variable 'ident'
Fix this by removing 'const' qualifier from watchdog_info struct.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
spinlock need to be replaced by mutex because of sleep functions
inside wdt_send_data.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There are fitpc2 compatible boards that hang with existent i/o
operations order. Solution is to switch between writing to data
and command ports.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Watchdog configuration register and timer count register were interchanged,
causing wrong values to be written into both registers.
This caused watchdog triggered resets even if the watchdog was reset in time.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Correct fix for the "ioremap() causes build failure on S390" should have been
a dependancy on HAS_IOMEM. So we add this dependancy also (and leave the driver
in the ARM section for now).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
When shutting down the watchdog timer, special care must be taken
not to overwrite other bits in the register, as it may be shared
with other peripherals.
For example, on the Arcom Vulcan, the register is shared between
the watchdog and the PCI reset line...
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A previous fix changed the WDTP function to use the period directly,
rather than subtracting from 63. However the mask generation was
not changed, so the mask was coming out as 0. This patch fixes it.
Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch allows Watchdog timer to be selected for OMAP4 by fixing
Kconfig entry
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] hpwdt - fix lower timeout limit
[WATCHDOG] iTCO_wdt: TCO Watchdog patch for additional Intel Cougar Point DeviceIDs
[WATCHDOG] doc: Fix use of WDIOC_SETOPTIONS ioctl.
[WATCHDOG] doc: watchdog simple example: don't fail on fsync()
[WATCHDOG] set max63xx driver as ARM only
[WATCHDOG] powerpc: pika_wdt ident cannot be const
[Novell Bug 581103] HP Watchdog driver has arbitrary (wrong) timeout limits.
Fix the lower timeout limit to a more appropriate value.
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@kernel.org>
Use of ioremap() causes build failure on S390.
Restrict the driver to ARM until another architecture comes along
and enables the driver for its own use.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The watchdog_info struct cannot be a const since we dynamically fill
in the firmware version.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Since the intel 6300esb platform uses a dedicated PCI ID for
it's watchdog timer (00:1d.4), it's better and easier to have
this as a pci_driver.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Before you can read or write from the i6300esb memeory mapped registers,
you need to unlock these. This is done by writing the magic numbers 0x80
and 0x86 to the reload register. The size of the reload register is 32bit
though.
Also binary 11 is hex 0x03 and not 0x11.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Making this instance static exposes the code to SMP races, etc.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Platform device drivers can use the .shutdown method to handle soft
shutdown's instead of reboot_notifier's.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch corrects author and copyright notices following the split-up of
the GE Fanuc joint venture.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
It's possible that the platform is not allowing reboot via TCO timer
expiration.
Also, differentiate between not finding a chipset that has TCO, and the case
where TCO is present but the driver fails to initialize for some reason.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Clean-up driver:
* make release the reverse of probe so that both are consistent
* add WDIOC_GETSTATUS & WDIOC_GETBOOTSTATUS ioctls.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This driver adds support for the max63{69,70,71,72,73,74} family of
watchdog timer chips.
It has been tested on an Arcom Zeus (max6369).
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Technologic Systems TS-72xx SBCs have external glue logic
CPLD which includes watchdog timer. This driver implements
kernel support for that.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch makes the ar7 clock code implement the Linux clk API. Drivers
using the various clocks available in the SoC are updated accordingly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
To: linux-mips@linux-mips.org
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: netdev@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Patchwork: http://patchwork.linux-mips.org/patch/881/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Relying on overflow/wrap around isn't exact because if you wrap far
enough, you get back to "valid" values.
Reported-by: Thorsten Pohlmann <pohlmann@tetronik.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@kernel.org>
clk_set_rate() is not supposed to be used to turn clocks on and off.
That's what clk_enable/clk_disable is for.
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mdelay function was used between I/O access commands, that causes peak
in CPU usage. Fix it by substitution mdelay to msleep.
Expand usage on fitPC2 compatible boards according to DMI identification.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the Intel Cougar Point and PCH DeviceIDs for iTCO Watchdog.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Kevin Hilman <khilman@ti.deeprootsystems.com>
Cc: Ulrik Bech Hald <ubh@ti.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Vincent Sanders <support@simtec.co.uk>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Update to the new cs5535_mfgpt* API. The geode-specific wording should
eventually be dropped from this driver...
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The platform has never been fully merged
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
This patch renames function names like twl4030_i2c_write_u8,
twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8
and also common variable in twl-core.c
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (151 commits)
powerpc: Fix usage of 64-bit instruction in 32-bit altivec code
MAINTAINERS: Add PowerPC patterns
powerpc/pseries: Track previous CPPR values to correctly EOI interrupts
powerpc/pseries: Correct pseries/dlpar.c build break without CONFIG_SMP
powerpc: Make "intspec" pointers in irq_host->xlate() const
powerpc/8xx: DTLB Miss cleanup
powerpc/8xx: Remove DIRTY pte handling in DTLB Error.
powerpc/8xx: Start using dcbX instructions in various copy routines
powerpc/8xx: Restore _PAGE_WRITETHRU
powerpc/8xx: Add missing Guarded setting in DTLB Error.
powerpc/8xx: Fixup DAR from buggy dcbX instructions.
powerpc/8xx: Tag DAR with 0x00f0 to catch buggy instructions.
powerpc/8xx: Update TLB asm so it behaves as linux mm expects.
powerpc/8xx: Invalidate non present TLBs
powerpc/pseries: Serialize cpu hotplug operations during deactivate Vs deallocate
pseries/pseries: Add code to online/offline CPUs of a DLPAR node
powerpc: stop_this_cpu: remove the cpu from the online map.
powerpc/pseries: Add kernel based CPU DLPAR handling
sysfs/cpu: Add probe/release files
powerpc/pseries: Kernel DLPAR Infrastructure
...
Remove the old WDT implementation.
Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6:
sparc: Set UTS_MACHINE correctly.
sparc,leon: init_leon srmmu cleanup
sparc32: Remove early interrupt enable.
sparc, leon: Added Aeroflex Gaisler entry in manufacturer_info structure
sparc64: Faster early-boot framebuffer console.
Revert "sparc: Make atomic locks raw"
sparc: remove unused nfsd #includes
sparc: Fixup last users of irq_chip->typename
Added sparc_leon3_snooping_enabled() and converted extern inline to static inline
No auxio on LEON
apbuart: Use of_find_node_by_path to find root node.
sparc: Replace old style lock initializer
sparc: Make atomic locks raw
apbuart: Fix build and missing driver unregister.
apbuart: Kill dependency on deprecated Sparc-only PROM interfaces.
apbuart: Fix build warning.
sparc: Support for GRLIB APBUART serial port
watchdog: Remove BKL from rio watchdog driver
sparc: Remove BKL from apc
sparc,leon: Sparc-Leon SMP support
Add support for CPU frequency scaling to the S3C24XX Watchdog
driver.
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch fixes the compilation failure of
rc32434 due to a bad module parameter description.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The size value passed to ioremap_nocache() is not correct.
Use resource_size() to get the correct value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The PNX core code calls the device 'pnx4008-watchdog' not 'watchdog'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
cycle_kernel_lock() was added with the BKL pushdown. The rio driver
indeed needs that because riowd_device is initialized after
misc_register(). So an open(), write/ioctl() which happens to get
between misc_register returning and riowd_device initialization would
dereference a NULL pointer.
Move riowd_device initialization before misc_register() and get rid of
cycle_kernel_lock().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
After sucessfully registering the misc device the driver iounmaps the
hardware registers and kfree's the device data structure. Ouch !
This was introduced with commit e42311d75 (riowatchdog: Convert to
pure OF driver) and went unnoticed for more than a year :)
Return success instead of dropping into the error cleanup code path.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the watchdog timer on Avionic Design Xanthos
boards.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix printk format warning:
drivers/watchdog/wdt_pci.c:652: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'resource_size_t'
and then use resource_size_t for the "io" variable as well
so that it won't be truncated.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch converts the ar7_wdt driver to become
a platform driver. The AR7 SoC specific identification
and base register calculation is performed by the board
code, therefore we no longer need to have access to
ar7_chip_id. We also remove the reboot notifier code to
use the platform shutdown method as Wim suggested.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WDIOC_SETTIMEOUT argument is supposed to be a "seconds" value.
However, the book E wdt currently treats it as a "period" which is
interpreted in a board-specific way.
This patch allows the user to pass in a "seconds" value and the driver
will set the smallest timeout that is at least as large as specified
by the user. It's been tested on e500 hardware and works as
expected.
The patch only modifies the CONFIG_FSL_BOOKE case, the CONFIG_4xx case
is left unmodified as I don't have any hardware to test it on.
Signed-off-by: Chris Friesen <cfriesen@nortel.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove use of CLOCK_TICK_RATE in favor of using clock framework
for getting timer frequency.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
I saw Julia Lawalls various commits fixing up the use of rounding
macros and since my already submitted patch was not caught in this
I took it upon myself to fix it up for this driver as well.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WM831x series of devices provide a watchdog with configurable
behaviour on timer expiry.
Currently this driver support refreshes via a register or GPIO line and
autonomous refreshes from a hardware source (eg, a clock).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add watchdog device driver for the Nuvoton NUC900 series SoCs.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add support for watchdog found on SBC-FITPC2 board.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
AR7 is currently being resubmitted for mainline inclusion
and we changed the path to the ar7-specific headers
from ar7 to mach-ar7 to reflect the other MIPS-based
boards header hierarchy. This patch will avoid any future
compilation failure due to missing headers.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Stop referencing CLOCK_TICK_RATE in the KS8695 drivers, rather refer
to a KS8695_CLOCK_RATE.
Issue pointed out by Russell King on arm-linux-kernel mailing list.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the COH 901 327 found in U300 is clocked at 32 kHz we need
to wait for the interrupt clearing flag to propagate through
hardware in order not to accidentally fire off any interrupts
when we enable them.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix a number of build errors in the ep93xx watchdog driver due
to missing io.h
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the W83627EHF/EF and W83627EHG/EG chipsets.
Signed-off-by: Slobodan Tomić <stomic@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch replaces the hardcoded 255 seconds limit for a real limit based on
oscr_freq.
Also, the 'firmware_version' field is changed to '1' to allow the user
space application to easily detect that this driver supports a higher
maximum timeout.
Signed-off-by: Raphael Assenat <raph@8D.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Don't forget to unlock io_lock when w83697ug_select_wd_register fails in
wdt_ctrl.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Using the RTAS watchdog driver to read out the temperature crashes
on a PXCAB:
Unable to handle kernel paging request for data at address 0xfe347b50
Faulting instruction address: 0xc00000000001af64
Oops: Kernel access of bad area, sig: 11 [#1]
The wrong usage of "(void *)__pa(&temperature)" in rtas_call() is
removed by using the function rtas_get_sensor() which does the
right thing.
Signed-off-by: Adrian Reber <adrian@lisas.de>
Acked-by: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change the wdt_pci.c watchdog driver so that the code is the same for
both the PCI-WDT500 as the PCI-WDT501 card. The selection of the card
is now being done via the module parameter: 'type' instead of the
config option CONFIG_WDT_501_PCI.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a priority option so that the user can choose if we do the NMI
first or last.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch contains two fixes:
1)In omap_wdt_probe() the watchdog is reset and disabled. This
requires register access and the clks needs to be enabled temporarily
2)In omap_wdt_open() the timer register needs to be reloaded
to trigger a new timer value (the default of 60s)
Tested on OMAP34xx platform (Zoom1)
Reviewed-by: Kevin Hilman <khilman@ti.deeprootsystems.com>
Signed-off-by: Ulrik Bech Hald <ubh@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This add watchdog driver for broadcom 47xx device.
It uses the ssb subsytem to access embeded watchdog device.
Because the watchdog timeout is very short (about 2s), a soft timer is used
to increase the watchdog period.
Note : A patch for exporting the ssb_watchdog_timer_set will
be submitted on next linux-mips merge. Without this patch it can't
be build as a module.
Signed-off-by: Aleksandar Radovanovic <biblbroks@sezampro.rs>
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Tested-by: Florian Fainelli <florian@openwrt.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Implementation of twl4030 watchdog driver.
Signed-off-by: Timo Kokkonen <timo.t.kokkonen@nokia.com>
Signed-off-by: Atal Shargorodsky <ext-atal.shargorodsky@nokia.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds support for the U300 COH 901 327 watchdog for the
U300 platform recently added to RMK:s ARM tree.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add NMI sourcing functionality (Can only be active if nmi_watchdog is
inactive).
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Bugzilla: 9868 & 10195.
There seems to be a bug into the SMM code that handles TCO Timeout SMI.
Andriy Gapon found that the code on his DG33TL system does the following:
> The handler is quite simple - it tests value in TCO1_CNT against 0x800, i.e.
> checks TCO_TMR_HLT. If the bit is set the handler goes into an infinite loop,
> apparently to allow the second timeout and reboot. Otherwise it simply clears
> TIMEOUT bit in TCO1_STS and that's it.
> So the logic seems to be reversed, because it is hard to see how TIMEOUT can
> get set to 1 and SMI generated when TCO_TMR_HLT is set (other than a
> transitional effect).
The only trick we have is to bypass the SMM code by turning of the generation
of the SMI#. The trick can only be enabled by setting the vendorsupport module
parameter to 911. This trick doesn't work well on laptop's.
Note: this is a dirty hack. Please handle with care. The only real fix is that
the bug in the SMM bios code get's fixed.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
According to 9.1.33 on p.343 of ICH8.pdf RCBA can be disabled by
hardware if bit 0 of RCBA register is not set.
Perform correct check for this to prevent memory corruption under
some virtual machines where this feature is disabled.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Vasily Averin <vvs@openvz.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
A pointer to probe and remove functions is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
So far, MPC512x used mpc512x_find_ips_freq() to get the bus frequency,
while MPC52xx used mpc52xx_find_ipb_freq(). Despite the different
clock names (IPS vs. IPB) the code was identical.
Use common code for both processor families.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Orion watchdog driver is also used on Kirkwood.
Convention is to use orion5x for stuff specific to 88F5xxx Orion chips
and simply "orion" for shared stuff across SoCs including Kirkwood.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The Kirkwood architecture uses the same watchdog device as the Orion
architecture. This patch adds orion5x_wdt as a platform device for
Kirkwood.
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The name of the define for the Reset-Out-Mask register as well as its
bit for the watchdog reset are changed to match the names used for
Kirkwood (which in turn match the processor specification more
closely). There is no functional change.
This patch prepares for adding orion5x_wdt as a platform device to
Kirkwood.
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Symbols like SOFT_RESET are way too generic to be exported at large.
To avoid this, let's move the mbus bridge register defines into a
separate file and include it where needed. This affects mach-kirkwood,
mach-loki, mach-mv78xx0 and mach-orion5x simultaneously as they all
share code in plat-orion which relies on those defines.
Some other defines have been moved to narrower scopes, or simply deleted
when they had no user.
This fixes compilation problem with mpt2sas on the above listed
platforms.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A pointer to omap_wdt_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alan Cox <alan@redhat.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: George G. Davis <gdavis@mvista.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A pointer to ks8695wdt_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alan Cox <alan@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A pointer to at91wdt_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ilpo Jarvinen <ilpo.jarvinen@helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Removes ARM26 sections from Kconfig and Makefile, because
ARM26 is long gone.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* Added a callback to disable the watchdog on shutdown.
* Use a separate ping function to reduce the number of register accesses
if the watchdog is already enabled and just needs to be reloaded.
* Minor cleanup of function names.
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The i6300ESB watchdog should be stopped before userspace has access to the
watchdog. So fix this and restructure the initialization sequence into:
* See if we have a i6300 device
* make sure that we have valid module parameters
* Initialize the device
* register the /dev/watchdog device so that userspace has access
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The buffer passed to the ibm,get-system-parameter RTAS call must be
in the RMA. To ensure we pass an address in the RMA use rtas_data_buf
for the actual RTAS call and then copy the result to value. We can't
just make it static because this can be compiled in as a module.
Also add the WDRTAS_SP_SPI_LEN so we don't litter '4' throughout the
function.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Tested-by: Adrian Reber <adrian@lisas.de>
Acked-by: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (fschmd) Add support for the FSC Hades IC
hwmon: (fschmd) Add support for the FSC Syleus IC
i2c-i801: Instantiate FSC hardware montioring chips
dmi: Let dmi_walk() users pass private data
hwmon: Define a standard interface for chassis intrusion detection
Move the pcf8591 driver to hwmon
hwmon: (w83627ehf) Only expose in6 or temp3 on the W83667HG
hwmon: (w83627ehf) Add support for W83667HG
hwmon: (w83627ehf) Invert fan pin variables logic
hwmon: (hdaps) Fix Thinkpad X41 axis inversion
hwmon: (hdaps) Allow inversion of separate axis
hwmon: (ds1621) Clean up documentation
hwmon: (ds1621) Avoid unneeded register access
hwmon: (ds1621) Clean up register access
hwmon: (ds1621) Reorder code statements
At the moment, dmi_walk() lacks flexibility, users can't pass data to
the callback function. Add a pointer for private data to make this
function more flexible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Roland Dreier <rolandd@cisco.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (422 commits)
[ARM] 5435/1: fix compile warning in sanity_check_meminfo()
[ARM] 5434/1: ARM: OMAP: Fix mailbox compile for 24xx
[ARM] pxa: fix the bad assumption that PCMCIA sockets always start with 0
[ARM] pxa: fix Colibri PXA300 and PXA320 LCD backlight pins
imxfb: Fix TFT mode
i.MX21/27: remove ifdef CONFIG_FB_IMX
imxfb: add clock support
mxc: add arch_reset() function
clkdev: add possibility to get a clock based on the device name
i.MX1: remove fb support from mach-imx
[ARM] pxa: build arch/arm/plat-pxa/mfp.c only when PXA3xx or ARCH_MMP defined
Gemini: Add support for Teltonika RUT100
Gemini: gpiolib based GPIO support v2
MAINTAINERS: add myself as Gemini architecture maintainer
ARM: Add Gemini architecture v3
[ARM] OMAP: Fix compile for omap2_init_common_hw()
MAINTAINERS: Add myself as Faraday ARM core variant maintainer
ARM: Add support for FA526 v2
[ARM] acorn,ebsa110,footbridge,integrator,sa1100: Convert asm/io.h to linux/io.h
[ARM] collie: fix two minor formatting nits
...
Change the start function in preparation of the generic watchdog code.
Also make sure that locking of the start function is OK.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Change the wdt.c watchdog driver so that the code is the same for
both the WDT500 as the WDT501-P card. The selection of the card
is now being done via the module parameter: 'type' instead of the
config option CONFIG_WDT_501.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix following includes:
* #include <asm/io.h> should be #include <linux/io.h>
* #include <asm/uaccess.h> should be #include <linux/uaccess.h>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add the PCI-ID for the upcoming new BMC controller for HP hardware.
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The orion5x-wdt driver is now registered as a platform device and
receives the tclk value as platform data. This fixes a compile issue
cause by a previously removed define "ORION5X_TCLK".
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Kristof Provost <kristof@sigsegv.be>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Martin Michlmayr <tbm@cyrius.com>
Cc: Sylver Bruneau <sylver.bruneau@googlemail.com>
Cc: Kunihiko IMAI <bak@d2.dion.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Make sure that the watchdog is not running after loading
and before it is started by opening /dev/watchdog.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WDT timer ticks quite fast (half of the CPU clock speed, which may
be between 198MHz and 330MHz (or 400MHz on newer boards)). Given it's
size of 32Bit, the maximum timeout value ranges from about 21s to 43s,
depending on the configured CPU clock speed.
This patch add's the timeout module parameter and checks that it's not
bigger then the maximum timeout for the given clock speed.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Clean-up the rc32434 driver code:
- name the platform driver rc32434_wdt_driver
- Replace KBUILD_MODNAME ": " with PFX define.
- Cleanup include files
- Order the ioctl's
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove davinci platform-specific IO accessor macros in favor
of standard ioremap + io[read|write]* functions.
Also, convert printk(KERN_ERR ....) into dev_err(...)
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
I noticed the W83697UG driver tries to register a watchdog even though
it already noticed the chip isn't there.
WDT driver for the Winbond(TM) W83697UG/UF Super I/O chip initialising.
w83697ug/uf WDT: No W83697UG/UF could be found
w83697ug/uf WDT: Watchdog already running. Resetting timeout to 60 sec
w83697ug/uf WDT: cannot register miscdev on minor=130 (err=-16)
Patch propagates the error back to wdt_init().
Signed-off-by: Eric Lammerts <eric@lammerts.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch fixes the bug reported in
http://bugzilla.kernel.org/show_bug.cgi?id=11681.
"Lots of device drivers register a 'struct device_driver' with
the '.bus' member set to '&platform_bus_type'. This is wrong,
since the platform_bus functions expect the 'struct device_driver'
to be wrapped up in a 'struct platform_driver' which provides
some additional callbacks (like suspend_late, resume_early).
The effect may be that platform_suspend_late() uses bogus data
outside the device_driver struct as a pointer pointer to the
device driver's suspend_late() function or other hard to
reproduce failures."(Lothar Wassmann)
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support for the PPC9A VME Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the basic board support for GE Fanuc's PPC9A, a 6U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The remaining registers are separated into:
- <mach/regs-ost.h>
- <mach/regs-rtc.h>
- <mach/regs-intc.h>
and then we can remove pxa-regs.h completely. Instead of #include this
file, let's:
1. include the specific <mach/regs-*.h> with care (if that's absolutely
necessary)
2. define the registers in the driver, make cleanly defined API to expose
the register access to external with sufficient reason
Signed-off-by: Eric Miao <eric.miao@marvell.com>
orion5x_wdt no longer compiled after the changes in commit
ebe35aff88 ("Orion: prepare for
runtime-determined timer tick rate").
The tick rate define (ORION5X_TCLK) was removed in favor of a runtime
detection. The quick fix is to add the define in the watchdog driver.
The fix is not correct for all supported orion5x platforms, but since
the supported platforms right now are 133 Mhz and 166 Mhz, it won't
be _that_ far off. ;-) A fix that uses the runtime-determined timer
tick rate will be applied later.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Kristof Provost <kristof@sigsegv.be>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Nicolas Pitre <nico@cam.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
fsl_get_sys_freq() may return -1 when 'soc' isn't found, but in
gef_wdt_probe() 'freq' is unsigned, so the test doesn't catch that.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
On arm-acs5k_tiny:
drivers/watchdog/ks8695_wdt.c:68: error: 'CLOCK_TICK_RATE' undeclared
(first use in this function)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@kernel.org>
The existing driver code wasn't working. Neither the timeout was set
correctly, nor system reset was being triggered, as the driver seemed
to keep the WDT alive himself. There was also some unnecessary code.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@kernel.org>
The recently merged AT91SAM9 watchdog driver uses the
AT91SAM9X_WATCHDOG config variable, whereas the original version of
the driver (and the platform support code) used AT91SAM9_WATCHDOG.
This causes the watchdog platform_device to never be registered, and
therefore the driver not to be initialized.
This patch:
- updates the platform support code to use AT91SAM9X_WATCHDOG.
- includes <linux/io.h> to fix compile error (same fix as was applied
to at91rm9200_wdt.c)
- fixes comment regarding watchdog clock-rates in at91rm9200.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
bugzilla: #12363
commit 7cd5b08be3 added a second regression:
some Dell's and Compaq's lockup on boot. So we revert most of the code.
The ICH9 reboot issue remains in place and will need some more fixing... :-(
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Support for the SBC310 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the basic board support for GE Fanuc's SBC310, a 3U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The driver was updated for OMAP34xx, but the Kconfig file was missed.
So this adds the missing parts from d99241c in Tony Lindgren's tree:
Add watchdog timer support for TI OMAP3430.
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Impact: cleanup
Move/remove leftover RDC321 files. Now that it's not a subarch anymore,
arch/x86/mach-rdc321x and arch/x86/include/asm/mach-rdc321x/ are not
needed.
One include file was still in use: rdc321x_defs.h, move that to the
generic x86 asm header directory.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The FPGA based watchdog timer used by the Pika Warp appliance.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
GE Fanuc SBC610
Support for the FPGA based watchdog timer as found on GE Fanuc's SBC310,
SBC610 and PPC9A Single Board Computers.
This patch adds support for the watchdog timer found in one of the devices
FPGAs. There are two identical watchdog timers at different offsets in the
above mentioned boards, this driver is capable of supporting one of them.
The watchdog timers are also capable of generating interrupts at a
user-configurable threshold, though support for this operation is currently
not supported by the driver.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The probe and remove functions were incorrectly annotated, with the
misannotation of the remove function causing build failures when built
in.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This driver implements support for the watchdog functionality provided
by the Wolfson Microelectronics WM8350, a multi-function audio and
power management subsystem intended for use in embedded systems. It is
based on a driver originally written by Graeme Gregory, though it has
been extensively modified since then.
Use of a GPIO to kick the watchdog is not yet supported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Add a watchdog driver for the hardware watchdog timer on the
SMSC SCH3112, SCH3114 and SCH3116 Super IO chipset.
Tested-by: Marco Chiappero <marco@absence.it>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
See description of commit:
[ARM] rtc-sa1100: don't assume CLOCK_TICK_RATE to be a constant
for additional information.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Prarit Bhargava