The HCI_BREDR naming is confusing since it actually stands for Primary
Bluetooth Controller. Which is a term that has been used in the latest
standard. However from a legacy point of view there only really have
been Basic Rate (BR) and Enhanced Data Rate (EDR). Recent versions of
Bluetooth introduced Low Energy (LE) and made this terminology a little
bit confused since Dual Mode Controllers include BR/EDR and LE. To
simplify this the name HCI_PRIMARY stands for the Primary Controller
which can be a single mode or dual mode controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
HCI_UART_PROTO_SET flag is set before hci_uart_set_proto call. If we
receive data from tty layer during this procedure, proto pointer may
not be assigned yet, leading to null pointer dereference in rx method
hci_uart_tty_receive.
This patch fixes this issue by introducing HCI_UART_PROTO_READY flag in
order to avoid any proto operation before proto opening and assignment.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This driver implements support for iBT2.1 Bluetooth controller embedded
in the AG620 communication combo. The controller needs to be configured
with bddata and can be patched with a binary patch file (pbn).
These operations are performed in manufacturing mode.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The N_HCI ldisc does not define a flush_buffer() ldisc method, so
the check when opening the ldisc is always false.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The new hci_skb_pkt_* wrappers are mainly intented for drivers to
require less knowledge about bt_cb(sbk) handling. So after converting
the core packet handling, convert all drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Provide an early indication about the manufacturer information so that
it can be forwarded into monitor channel.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Setting and clearing of HCI_RUNNING flag in each and every driver is
just duplicating the same code all over the place. So instead of having
the driver do it in their hdev->open and hdev->close callbacks, set it
globally in the core transport handling.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In all callbacks for hdev->send the status of HCI_RUNNING is checked. So
instead of repeating that code in every driver, move the check into the
hci_send_frame function before calling hdev->send.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
rx_lock spinlock is only used in hci_uart_tty_receive() which is the
receive_buf ldisc callback.
hci_uart_tty_receive() is protected from re-entrance by its only
caller (flush_to_ldisc() in drivers/tty/tty_buffer.c) which held a
mutex (buf->lock) for this section.
This lock allows "safe use of the line discipline's receive_buf()
method by excluding the buffer work and any pending flush from using
the flip buffer." (comments from tty_buffer_lock_exclusive() in
drivers/tty/tty_buffer.c)
So, no need to double protect this resource with rx_lock.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA61x4 chips have supported sleep feature using In-Band-Sleep commands
to enable sleep feature based on H4 protocol. After sending
patch/nvm configuration is done, IBS mode will be up and running
Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix for Cleanpatch warning:
Space prohibited between function name and open parenthesis '('
Signed-off-by: Prasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Intel Lightning Peak devices do not come with Bluetooth firmware
loaded and thus require a full download of the operational Bluetooth
firmware when the device is attached via the Bluetooth line discipline.
Lightning Peak devices start with a bootloader mode that only accepts
a very limited set of HCI commands. The supported commands are enough
to identify the hardware and select the right firmware to load.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hu->proto->*speed will always be used for all device where it is set.
But hu->*speed should be used if exist, so the test should be swapped.
The equivalent change is needed in bcm_setup() of hci_bcm.c.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Added the ability to flow control the UART, improved the UART baud
rate setting, transferred the speeds into line discipline from the
protocol and introduced the tty init function.
Signed-off-by: Ilya Faenson <ifaenson@broadcom.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add initial and operational speeds.
Change to operational speed as soon as possible. If controller
set_baudrate() fails, continue at initial speed.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Move request/release_firmware() out of btbcm_patchram().
This allows a better error management, if request_firmware() returns an
error then the controller will be used without firmware loading and 0 is
returned.
This will imply to change btbcm_patchram() to accept a firmware instead
of firmware name.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth address setting for Intel devices is provided by a generic
module now. Start using that module instead of relying it being included
in the driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the protocol support for Broadcom based UART devices to
enable firmware and patchram download procedure. It is a pretty
straight forward H:4 driver with the exception of actually having
its own setup and address configuration callbacks.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The new Broadcom Bluetooth support module provides generic functionality
for changing and checking the Bluetooth device address. Use these new
features instead of keeping a duplicate in the driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This version number is more cosmetic and for debugging purposes, but
since there has been a few changes lately, increase it now.
Two left-over and not used version constants that were never exposed
anywhere are removed since they have no actual value.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The init function for each HCI UART protocol prints the same on success
and failure. This information is so generic, remove it and let the main
HCI UART handling print it instead.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The usage of struct hci_uart_proto should always be const. Change the
function headers and individual protocol drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The TTY layer provides its data pointers as const, but the HCI UART
callbacks expect them as general data pointers. This is of course
wrong and instead of casting them, just fix the individual drivers
to actually take a const data pointer.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Casting the tty->disc_data to (void *) is not needed at all. So just
remove this cast and assign the object without a cast.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When using vendor detection, this adds support for the Broadcom
specific address configuration command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When using vendor detection, this adds support for the Intel specific
address configuration command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds a new HCI_UART_VND_DETECT flag to allow automatic vendor
detection. This allows to enable known vendor commands (for example
for setting the public device address) when using a standard H:4
UART protocol or when running in virtual machines.
When this new flag is configured and no vendor specific setup
routine is provided, then the local version information are read
and the provided manufacturer information can be evaluated to
configure extra vendor callbacks.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some Bluetooth controllers require initialization before being
used (vendor config, firmware download). Add possibility for a
HCI UART proto to implement this early init via the setup callback.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The protocol for the UART might be configured, but that does not
mean the HCI device is registered. Return an error in that case
and only return the index number when HCI_UART_REGISTERED is set.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The quirk for enabling external configuration with UART needs to be
provided via the HCI UART flags. Add a new flag for it and declare
it as valid.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Providing unknown or invalid flags to the HCI UART driver should
result in an error. So check which flags are valid and otherwise
return an error.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
LDISCs shouldn't call tty->ops->write() from within
->write_wakeup().
->write_wakeup() is called with port lock taken and
IRQs disabled, tty->ops->write() will try to acquire
the same port lock and we will deadlock.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reported-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Andreas Bießmann <andreas@biessmann.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove assignment in if-statements to be consistent with the coding
style.
Signed-off-by: Valentin Ilie <valentin.ilie@gmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of hci_uart_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of masking hdev inside the skb->dev parameter, hand it
directly to the driver as a parameter to hdev->send. This makes
the driver interface more clear and simpler.
This patch fixes all drivers to accept and handle the new parameter
of hdev->send callback. Special care has been taken for bpa10x
and btusb drivers that require having skb->dev set to hdev for
the URB transmit complete handlers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch removes redundant whitespace from the HCI ldisc driver.
Signed-off-by: Chan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds a NULL check for the HCI UART ldisc driver because some
of HCI UART drivers allow hci_uart_tty_receive function to be called
even though the HCI device hasn't been registered yet.
Signed-off-by: Chan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
hci_ldisc's open checks if tty_struct->disc_data is set. And if so it
returns with an error. But nothing ensures disc_data to be NULL. And
since ld->ops->open shall be called only once, we do not need the
check at all. So remove it.
Note that this is not an issue now, but n_tty will start using the
disc_data pointer and this invalid 'if' would trigger then rendering
TTYs over BT unusable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes it possible to have UART drivers perform an internal
initialization before calling hci_register_dev. This allows moving a lot
of init code from user space (hciattach) to the kernel side, thereby
creating a more controlled/robust initialization process.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch cleans up and reduces indentation in the hci_uart_tty_close
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds the initial skeleton for Three-wire UART (H5) support
and hooks it up to the HCI UART framework.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
HCI_QUIRK_NO_RESET name is misleading - purpose of this quirk is to
reset device on close instead of init, not to not reset at all.
Rename it to HCI_QUIRK_RESET_ON_CLOSE to avoid confusion.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We initialize the "struct device" in hci_alloc_dev() for a long time now
so we can access hdev->dev.parent directly. Hence, we can drop the
temporary field hdev->parent which is used in no other place than
hci_add_sysfs().
SET_HCIDEV_DEV() is never called after registering a device by the
drivers so we do not overwrite internal device-state. Furthermore,
hdev->dev is initialized to 0 by kzalloc() inside hci_alloc_dev() so the
default behavior with dev.parent = NULL is kept.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In reality this might never be used for real hardware, but it is a nice
feature for emulating AMP controllers within a virtual machine.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The flags ioctl for HCI UART drivers already allows setting of certain
Bluetooth core quirks. The reset parameter fits right in here. So allow
this as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann