This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
0day robot reported the following crash:
[ 21.233581] BUG: unable to handle kernel NULL pointer dereference at 0000000000000007
[ 21.234709] IP: [<ffffffff8156ebda>] sk_attach_bpf+0x39/0xc2
It's due to bpf_prog_get() returning ERR_PTR.
Check it properly.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: 89aa075832 ("net: sock: allow eBPF programs to be attached to sockets")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce helper macro for_each_cmsghdr as a wrapper of the enumerating
cmsghdr from msghdr, just cleanup.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge first patchbomb from Andrew Morton:
- a few minor cifs fixes
- dma-debug upadtes
- ocfs2
- slab
- about half of MM
- procfs
- kernel/exit.c
- panic.c tweaks
- printk upates
- lib/ updates
- checkpatch updates
- fs/binfmt updates
- the drivers/rtc tree
- nilfs
- kmod fixes
- more kernel/exit.c
- various other misc tweaks and fixes
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (190 commits)
exit: pidns: fix/update the comments in zap_pid_ns_processes()
exit: pidns: alloc_pid() leaks pid_namespace if child_reaper is exiting
exit: exit_notify: re-use "dead" list to autoreap current
exit: reparent: call forget_original_parent() under tasklist_lock
exit: reparent: avoid find_new_reaper() if no children
exit: reparent: introduce find_alive_thread()
exit: reparent: introduce find_child_reaper()
exit: reparent: document the ->has_child_subreaper checks
exit: reparent: s/while_each_thread/for_each_thread/ in find_new_reaper()
exit: reparent: fix the cross-namespace PR_SET_CHILD_SUBREAPER reparenting
exit: reparent: fix the dead-parent PR_SET_CHILD_SUBREAPER reparenting
exit: proc: don't try to flush /proc/tgid/task/tgid
exit: release_task: fix the comment about group leader accounting
exit: wait: drop tasklist_lock before psig->c* accounting
exit: wait: don't use zombie->real_parent
exit: wait: cleanup the ptrace_reparented() checks
usermodehelper: kill the kmod_thread_locker logic
usermodehelper: don't use CLONE_VFORK for ____call_usermodehelper()
fs/hfs/catalog.c: fix comparison bug in hfs_cat_keycmp
nilfs2: fix the nilfs_iget() vs. nilfs_new_inode() races
...
As it is, default ->i_fop has NULL ->open() (along with all other methods).
The only case where it matters is reopening (via procfs symlink) a file that
didn't get its ->f_op from ->i_fop - anything else will have ->i_fop assigned
to something sane (default would fail on read/write/ioctl/etc.).
Unfortunately, such case exists - alloc_file() users, especially
anon_get_file() ones. There we have tons of opened files of very different
kinds sharing the same inode. As the result, attempt to reopen those via
procfs succeeds and you get a descriptor you can't do anything with.
Moreover, in case of sockets we set ->i_fop that will only be used
on such reopen attempts - and put a failing ->open() into it to make sure
those do not succeed.
It would be simpler to put such ->open() into default ->i_fop and leave
it unchanged both for anon inode (as we do anyway) and for socket ones. Result:
* everything going through do_dentry_open() works as it used to
* sock_no_open() kludge is gone
* attempts to reopen anon-inode files fail as they really ought to
* ditto for aio_private_file()
* ditto for perfmon - this one actually tried to imitate sock_no_open()
trick, but failed to set ->i_fop, so in the current tree reopens succeed and
yield completely useless descriptor. Intent clearly had been to fail with
-ENXIO on such reopens; now it actually does.
* everything else that used alloc_file() keeps working - it has ->i_fop
set for its inodes anyway
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Memory is internally accounted in bytes, using spinlock-protected 64-bit
counters, even though the smallest accounting delta is a page. The
counter interface is also convoluted and does too many things.
Introduce a new lockless word-sized page counter API, then change all
memory accounting over to it. The translation from and to bytes then only
happens when interfacing with userspace.
The removed locking overhead is noticable when scaling beyond the per-cpu
charge caches - on a 4-socket machine with 144-threads, the following test
shows the performance differences of 288 memcgs concurrently running a
page fault benchmark:
vanilla:
18631648.500498 task-clock (msec) # 140.643 CPUs utilized ( +- 0.33% )
1,380,638 context-switches # 0.074 K/sec ( +- 0.75% )
24,390 cpu-migrations # 0.001 K/sec ( +- 8.44% )
1,843,305,768 page-faults # 0.099 M/sec ( +- 0.00% )
50,134,994,088,218 cycles # 2.691 GHz ( +- 0.33% )
<not supported> stalled-cycles-frontend
<not supported> stalled-cycles-backend
8,049,712,224,651 instructions # 0.16 insns per cycle ( +- 0.04% )
1,586,970,584,979 branches # 85.176 M/sec ( +- 0.05% )
1,724,989,949 branch-misses # 0.11% of all branches ( +- 0.48% )
132.474343877 seconds time elapsed ( +- 0.21% )
lockless:
12195979.037525 task-clock (msec) # 133.480 CPUs utilized ( +- 0.18% )
832,850 context-switches # 0.068 K/sec ( +- 0.54% )
15,624 cpu-migrations # 0.001 K/sec ( +- 10.17% )
1,843,304,774 page-faults # 0.151 M/sec ( +- 0.00% )
32,811,216,801,141 cycles # 2.690 GHz ( +- 0.18% )
<not supported> stalled-cycles-frontend
<not supported> stalled-cycles-backend
9,999,265,091,727 instructions # 0.30 insns per cycle ( +- 0.10% )
2,076,759,325,203 branches # 170.282 M/sec ( +- 0.12% )
1,656,917,214 branch-misses # 0.08% of all branches ( +- 0.55% )
91.369330729 seconds time elapsed ( +- 0.45% )
On top of improved scalability, this also gets rid of the icky long long
types in the very heart of memcg, which is great for 32 bit and also makes
the code a lot more readable.
Notable differences between the old and new API:
- res_counter_charge() and res_counter_charge_nofail() become
page_counter_try_charge() and page_counter_charge() resp. to match
the more common kernel naming scheme of try_do()/do()
- res_counter_uncharge_until() is only ever used to cancel a local
counter and never to uncharge bigger segments of a hierarchy, so
it's replaced by the simpler page_counter_cancel()
- res_counter_set_limit() is replaced by page_counter_limit(), which
expects its callers to serialize against themselves
- res_counter_memparse_write_strategy() is replaced by
page_counter_limit(), which rounds down to the nearest page size -
rather than up. This is more reasonable for explicitely requested
hard upper limits.
- to keep charging light-weight, page_counter_try_charge() charges
speculatively, only to roll back if the result exceeds the limit.
Because of this, a failing bigger charge can temporarily lock out
smaller charges that would otherwise succeed. The error is bounded
to the difference between the smallest and the biggest possible
charge size, so for memcg, this means that a failing THP charge can
send base page charges into reclaim upto 2MB (4MB) before the limit
would have been reached. This should be acceptable.
[akpm@linux-foundation.org: add includes for WARN_ON_ONCE and memparse]
[akpm@linux-foundation.org: add includes for WARN_ON_ONCE, memparse, strncmp, and PAGE_SIZE]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Vladimir Davydov <vdavydov@parallels.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull VFS changes from Al Viro:
"First pile out of several (there _definitely_ will be more). Stuff in
this one:
- unification of d_splice_alias()/d_materialize_unique()
- iov_iter rewrite
- killing a bunch of ->f_path.dentry users (and f_dentry macro).
Getting that completed will make life much simpler for
unionmount/overlayfs, since then we'll be able to limit the places
sensitive to file _dentry_ to reasonably few. Which allows to have
file_inode(file) pointing to inode in a covered layer, with dentry
pointing to (negative) dentry in union one.
Still not complete, but much closer now.
- crapectomy in lustre (dead code removal, mostly)
- "let's make seq_printf return nothing" preparations
- assorted cleanups and fixes
There _definitely_ will be more piles"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
copy_from_iter_nocache()
new helper: iov_iter_kvec()
csum_and_copy_..._iter()
iov_iter.c: handle ITER_KVEC directly
iov_iter.c: convert copy_to_iter() to iterate_and_advance
iov_iter.c: convert copy_from_iter() to iterate_and_advance
iov_iter.c: get rid of bvec_copy_page_{to,from}_iter()
iov_iter.c: convert iov_iter_zero() to iterate_and_advance
iov_iter.c: convert iov_iter_get_pages_alloc() to iterate_all_kinds
iov_iter.c: convert iov_iter_get_pages() to iterate_all_kinds
iov_iter.c: convert iov_iter_npages() to iterate_all_kinds
iov_iter.c: iterate_and_advance
iov_iter.c: macros for iterating over iov_iter
kill f_dentry macro
dcache: fix kmemcheck warning in switch_names
new helper: audit_file()
nfsd_vfs_write(): use file_inode()
ncpfs: use file_inode()
kill f_dentry uses
lockd: get rid of ->f_path.dentry->d_sb
...
Highlights include:
Features:
- NFSv4.2 client support for hole punching and preallocation.
- Further RPC/RDMA client improvements.
- Add more RPC transport debugging tracepoints.
- Add RPC debugging tools in debugfs.
Bugfixes:
- Stable fix for layoutget error handling
- Fix a change in COMMIT behaviour resulting from the recent io code updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wOP3
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.19-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Features:
- NFSv4.2 client support for hole punching and preallocation.
- Further RPC/RDMA client improvements.
- Add more RPC transport debugging tracepoints.
- Add RPC debugging tools in debugfs.
Bugfixes:
- Stable fix for layoutget error handling
- Fix a change in COMMIT behaviour resulting from the recent io code
updates"
* tag 'nfs-for-3.19-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (28 commits)
sunrpc: add a debugfs rpc_xprt directory with an info file in it
sunrpc: add debugfs file for displaying client rpc_task queue
nfs: Add DEALLOCATE support
nfs: Add ALLOCATE support
NFS: Clean up nfs4_init_callback()
NFS: SETCLIENTID XDR buffer sizes are incorrect
SUNRPC: serialize iostats updates
xprtrdma: Display async errors
xprtrdma: Enable pad optimization
xprtrdma: Re-write rpcrdma_flush_cqs()
xprtrdma: Refactor tasklet scheduling
xprtrdma: unmap all FMRs during transport disconnect
xprtrdma: Cap req_cqinit
xprtrdma: Return an errno from rpcrdma_register_external()
nfs: define nfs_inc_fscache_stats and using it as possible
nfs: replace nfs_add_stats with nfs_inc_stats when add one
NFS: Deletion of unnecessary checks before the function call "nfs_put_client"
sunrpc: eliminate RPC_TRACEPOINTS
sunrpc: eliminate RPC_DEBUG
lockd: eliminate LOCKD_DEBUG
...
Conflicts:
drivers/net/ethernet/amd/xgbe/xgbe-desc.c
drivers/net/ethernet/renesas/sh_eth.c
Overlapping changes in both conflict cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
Making things const is a good thing.
(x86-64 defconfig with all irda)
$ size net/irda/built-in.o*
text data bss dec hex filename
109276 1868 244 111388 1b31c net/irda/built-in.o.new
108828 2316 244 111388 1b31c net/irda/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's better when function pointer arrays aren't modifiable.
Net change:
$ size net/llc/built-in.o.*
text data bss dec hex filename
61193 12758 1344 75295 1261f net/llc/built-in.o.new
47113 27030 1344 75487 126df net/llc/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's better when function pointer arrays aren't modifiable.
Net change from original:
$ size net/llc/built-in.o.*
text data bss dec hex filename
61065 12886 1344 75295 1261f net/llc/built-in.o.new
47113 27030 1344 75487 126df net/llc/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's better when function pointer arrays aren't modifiable.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch effectively reverts commit 500f808726 ("net: ovs: use CRC32
accelerated flow hash if available"), and other remaining arch_fast_hash()
users such as from nfsd via commit 6282cd5655 ("NFSD: Don't hand out
delegations for 30 seconds after recalling them.") where it has been used
as a hash function for bloom filtering.
While we think that these users are actually not much of concern, it has
been requested to remove the arch_fast_hash() library bits that arose
from [1] entirely as per recent discussion [2]. The main argument is that
using it as a hash may introduce bias due to its linearity (see avalanche
criterion) and thus makes it less clear (though we tried to document that)
when this security/performance trade-off is actually acceptable for a
general purpose library function.
Lets therefore avoid any further confusion on this matter and remove it to
prevent any future accidental misuse of it. For the time being, this is
going to make hashing of flow keys a bit more expensive in the ovs case,
but future work could reevaluate a different hashing discipline.
[1] https://patchwork.ozlabs.org/patch/299369/
[2] https://patchwork.ozlabs.org/patch/418756/
Cc: Neil Brown <neilb@suse.de>
Cc: Francesco Fusco <fusco@ntop.org>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For netlink, we shouldn't be using arch_fast_hash() as a hashing
discipline, but rather jhash() instead.
Since netlink sockets can be opened by any user, a local attacker
would be able to easily create collisions with the DPDK-derived
arch_fast_hash(), which trades off performance for security by
using crc32 CPU instructions on x86_64.
While it might have a legimite use case in other places, it should
be avoided in netlink context, though. As rhashtable's API is very
flexible, we could later on still decide on other hashing disciplines,
if legitimate.
Reference: http://thread.gmane.org/gmane.linux.kernel/1844123
Fixes: e341694e3e ("netlink: Convert netlink_lookup() to use RCU protected hash table")
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 908344cdda ("tipc: fix bug in multicast congestion handling")
introduced a race in the broadcast link wakeup functionality.
This patch eliminates this broadcast link wakeup race caused by
operation on the wakeup list without proper locking. If this race
hit and corrupted the list all subsequent wakeup messages would be
lost, resulting in a considerable memory leak.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change pulls the core functionality out of __netdev_alloc_skb and
places them in a new function named __alloc_rx_skb. The reason for doing
this is to make these bits accessible to a new function __napi_alloc_skb.
In addition __alloc_rx_skb now has a new flags value that is used to
determine which page frag pool to allocate from. If the SKB_ALLOC_NAPI
flag is set then the NAPI pool is used. The advantage of this is that we
do not have to use local_irq_save/restore when accessing the NAPI pool from
NAPI context.
In my test setup I saw at least 11ns of savings using the napi_alloc_skb
function versus the netdev_alloc_skb function, most of this being due to
the fact that we didn't have to call local_irq_save/restore.
The main use case for napi_alloc_skb would be for things such as copybreak
or page fragment based receive paths where an skb is allocated after the
data has been received instead of before.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits the netdev_alloc_frag function up so that it can be used
on one of two page frag pools instead of being fixed on the
netdev_alloc_cache. By doing this we can add a NAPI specific function
__napi_alloc_frag that accesses a pool that is only used from softirq
context. The advantage to this is that we do not need to call
local_irq_save/restore which can be a significant savings.
I also took the opportunity to refactor the core bits that were placed in
__alloc_page_frag. First I updated the allocation to do either a 32K
allocation or an order 0 page. This is based on the changes in commmit
d9b2938aa where it was found that latencies could be reduced in case of
failures. Then I also rewrote the logic to work from the end of the page to
the start. By doing this the size value doesn't have to be used unless we
have run out of space for page fragments. Finally I cleaned up the atomic
bits so that we just do an atomic_sub_and_test and if that returns true then
we set the page->_count via an atomic_set. This way we can remove the extra
conditional for the atomic_read since it would have led to an atomic_inc in
the case of success anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle are:
- 'Nested Sleep Debugging', activated when CONFIG_DEBUG_ATOMIC_SLEEP=y.
This instruments might_sleep() checks to catch places that nest
blocking primitives - such as mutex usage in a wait loop. Such
bugs can result in hard to debug races/hangs.
Another category of invalid nesting that this facility will detect
is the calling of blocking functions from within schedule() ->
sched_submit_work() -> blk_schedule_flush_plug().
There's some potential for false positives (if secondary blocking
primitives themselves are not ready yet for this facility), but the
kernel will warn once about such bugs per bootup, so the warning
isn't much of a nuisance.
This feature comes with a number of fixes, for problems uncovered
with it, so no messages are expected normally.
- Another round of sched/numa optimizations and refinements, for
CONFIG_NUMA_BALANCING=y.
- Another round of sched/dl fixes and refinements.
Plus various smaller fixes and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
sched: Add missing rcu protection to wake_up_all_idle_cpus
sched/deadline: Introduce start_hrtick_dl() for !CONFIG_SCHED_HRTICK
sched/numa: Init numa balancing fields of init_task
sched/deadline: Remove unnecessary definitions in cpudeadline.h
sched/cpupri: Remove unnecessary definitions in cpupri.h
sched/deadline: Fix rq->dl.pushable_tasks bug in push_dl_task()
sched/fair: Fix stale overloaded status in the busiest group finding logic
sched: Move p->nr_cpus_allowed check to select_task_rq()
sched/completion: Document when to use wait_for_completion_io_*()
sched: Update comments about CLONE_NEWUTS and CLONE_NEWIPC
sched/fair: Kill task_struct::numa_entry and numa_group::task_list
sched: Refactor task_struct to use numa_faults instead of numa_* pointers
sched/deadline: Don't check CONFIG_SMP in switched_from_dl()
sched/deadline: Reschedule from switched_from_dl() after a successful pull
sched/deadline: Push task away if the deadline is equal to curr during wakeup
sched/deadline: Add deadline rq status print
sched/deadline: Fix artificial overrun introduced by yield_task_dl()
sched/rt: Clean up check_preempt_equal_prio()
sched/core: Use dl_bw_of() under rcu_read_lock_sched()
sched: Check if we got a shallowest_idle_cpu before searching for least_loaded_cpu
...
commit 46e5da40ae (net: qdisc: use rcu prefix and silence
sparse warnings) triggers a spurious warning:
net/sched/sch_fq_codel.c:97 suspicious rcu_dereference_check() usage!
The code should be using the _bh variant of rcu_dereference.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I cooked commit c3658e8d0f ("tcp: fix possible NULL dereference in
tcp_vX_send_reset()") I missed other spots we could deref a NULL
skb_dst(skb)
Again, if a socket is provided, we do not need skb_dst() to get a
pointer to network namespace : sock_net(sk) is good enough.
Reported-by: Dann Frazier <dann.frazier@canonical.com>
Bisected-by: Dann Frazier <dann.frazier@canonical.com>
Tested-by: Dann Frazier <dann.frazier@canonical.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: ca777eff51 ("tcp: remove dst refcount false sharing for prequeue mode")
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit fb9962f3ce ("tipc: ensure all name sequences are properly
protected with its lock") involves below errors:
net/tipc/name_table.c:980 tipc_purge_publications() error: double lock 'spin_lock:&seq->lock'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove use of 'swdev' mode in rocker. rocker dev offloads
can use the BRIDGE_FLAGS_SELF to indicate offload to hardware.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-12-08
Please pull this last batch of pending wireless updates for the 3.19 tree...
For the wireless bits, Johannes says:
"This time I have Felix's no-status rate control work, which will allow
drivers to work better with rate control even if they don't have perfect
status reporting. In addition to this, a small hwsim fix from Patrik,
one of the regulatory patches from Arik, and a number of cleanups and
fixes I did myself.
Of note is a patch where I disable CFG80211_WEXT so that compatibility
is no longer selectable - this is intended as a wake-up call for anyone
who's still using it, and is still easily worked around (it's a one-line
patch) before we fully remove the code as well in the future."
For the Bluetooth bits, Johan says:
"Here's one more bluetooth-next pull request for 3.19:
- Minor cleanups for ieee802154 & mac802154
- Fix for the kernel warning with !TASK_RUNNING reported by Kirill A.
Shutemov
- Support for another ath3k device
- Fix for tracking link key based security level
- Device tree bindings for btmrvl + a state update fix
- Fix for wrong ACL flags on LE links"
And...
"In addition to the previous one this contains two more cleanups to
mac802154 as well as support for some new HCI features from the
Bluetooth 4.2 specification.
From the original request:
'Here's what should be the last bluetooth-next pull request for 3.19.
It's rather large but the majority of it is the Low Energy Secure
Connections feature that's part of the Bluetooth 4.2 specification. The
specification went public only this week so we couldn't publish the
corresponding code before that. The code itself can nevertheless be
considered fairly mature as it's been in development for over 6 months
and gone through several interoperability test events.
Besides LE SC the pull request contains an important fix for command
complete events for mgmt sockets which also fixes some leaks of hci_conn
objects when powering off or unplugging Bluetooth adapters.
A smaller feature that's part of the pull request is service discovery
support. This is like normal device discovery except that devices not
matching specific UUIDs or strong enough RSSI are filtered out.
Other changes that the pull request contains are firmware dump support
to the btmrvl driver, firmware download support for Broadcom BCM20702A0
variants, as well as some coding style cleanups in 6lowpan &
ieee802154/mac802154 code.'"
For the NFC bits, Samuel says:
"With this one we get:
- NFC digital improvements for DEP support: Chaining, NACK and ATN
support added.
- NCI improvements: Support for p2p target, SE IO operand addition,
SE operands extensions to support proprietary implementations, and
a few fixes.
- NFC HCI improvements: OPEN_PIPE and NOTIFY_ALL_CLEARED support,
and SE IO operand addition.
- A bunch of minor improvements and fixes for STMicro st21nfcb and
st21nfca"
For the iwlwifi bits, Emmanuel says:
"Major works are CSA and TDLS. On top of that I have a new
firmware API for scan and a few rate control improvements.
Johannes find a few tricks to improve our CPU utilization
and adds support for a new spin of 7265 called 7265D.
Along with this a few random things that don't stand out."
And...
"I deprecate here -8.ucode since -9 has been published long ago.
Along with that I have a new activity, we have now better
a infrastructure for firmware debugging. This will allow to
have configurable probes insides the firmware.
Luca continues his work on NetDetect, this feature is now
complete. All the rest is minor fixes here and there."
For the Atheros bits, Kalle says:
"Only ath10k changes this time and no major changes. Most visible are:
o new debugfs interface for runtime firmware debugging (Yanbo)
o fix shared WEP (Sujith)
o don't rebuild whenever kernel version changes (Johannes)
o lots of refactoring to make it easier to add new hw support (Michal)
There's also smaller fixes and improvements with no point of listing
here."
In addition, there are a few last minute updates to ath5k,
ath9k, brcmfmac, brcmsmac, mwifiex, rt2x00, rtlwifi, and wil6210.
Also included is a pull of the wireless tree to pick-up the fixes
originally included in "pull request: wireless 2014-12-03"...
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
the queue length of sd->input_pkt_queue has been put into qlen,
and impossible to change, since hold the lock
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=icE1
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-3.19-20141207' of git://gitorious.org/linux-can/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2014-12-07
this is a pull request of 8 patches for net-next/master.
Andri Yngvason contributes 4 patches in which the CAN state change
handling is consolidated and unified among the sja1000, mscan and
flexcan driver. The three patches by Jeremiah Mahler fix spelling
mistakes and eliminate the banner[] variable in various parts. And a
patch by me that switches on sparse endianess checking by default.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 95bd09eb27 ("tcp: TSO packets automatic sizing") tried to
control TSO size, but did this at the wrong place (sendmsg() time)
At sendmsg() time, we might have a pessimistic view of flow rate,
and we end up building very small skbs (with 2 MSS per skb).
This is bad because :
- It sends small TSO packets even in Slow Start where rate quickly
increases.
- It tends to make socket write queue very big, increasing tcp_ack()
processing time, but also increasing memory needs, not necessarily
accounted for, as fast clones overhead is currently ignored.
- Lower GRO efficiency and more ACK packets.
Servers with a lot of small lived connections suffer from this.
Lets instead fill skbs as much as possible (64KB of payload), but split
them at xmit time, when we have a precise idea of the flow rate.
skb split is actually quite efficient.
Patch looks bigger than necessary, because TCP Small Queue decision now
has to take place after the eventual split.
As Neal suggested, introduce a new tcp_tso_autosize() helper, so that
tcp_tso_should_defer() can be synchronized on same goal.
Rename tp->xmit_size_goal_segs to tp->gso_segs, as this variable
contains number of mss that we can put in GSO packet, and is not
related to the autosizing goal anymore.
Tested:
40 ms rtt link
nstat >/dev/null
netperf -H remote -l -2000000 -- -s 1000000
nstat | egrep "IpInReceives|IpOutRequests|TcpOutSegs|IpExtOutOctets"
Before patch :
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/s
87380 2000000 2000000 0.36 44.22
IpInReceives 600 0.0
IpOutRequests 599 0.0
TcpOutSegs 1397 0.0
IpExtOutOctets 2033249 0.0
After patch :
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 2000000 2000000 0.36 44.27
IpInReceives 221 0.0
IpOutRequests 232 0.0
TcpOutSegs 1397 0.0
IpExtOutOctets 2013953 0.0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
... making both non-draining. That means that tcp_recvmsg() becomes
non-draining. And _that_ would break iscsit_do_rx_data() unless we
a) make sure tcp_recvmsg() is uniformly non-draining (it is)
b) make sure it copes with arbitrary (including shifted)
iov_iter (it does, all it uses is iov_iter primitives)
c) make iscsit_do_rx_data() initialize ->msg_iter only once.
Fortunately, (c) is doable with minimal work and we are rid of one
the two places where kernel send/recvmsg users would be unhappy with
non-draining behaviour.
Actually, that makes all but one of ->recvmsg() instances iov_iter-clean.
The exception is skcipher_recvmsg() and it also isn't hard to convert
to primitives (iov_iter_get_pages() is needed there). That'll wait
a bit - there's some interplay with ->sendmsg() path for that one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Just use copy_from_iter(). That's what this method is trying to do
in all cases, in a very convoluted fashion.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Note that the code _using_ ->msg_iter at that point will be very
unhappy with anything other than unshifted iovec-backed iov_iter.
We still need to convert users to proper primitives.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
it'll die soon enough - now that kvec-backed iov_iter works regardless
of set_fs(), both instances will become copy_from_iter() as soon as
we introduce ->msg_iter...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Since commit f886497212 ("ipv4: fix dst race in sk_dst_get()")
DST_NOCACHE dst_entries get freed by RCU. So there is no need to get a
reference on them when we are in rcu protected sections.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Respect what the caller passed to ovs_tunnel_get_egress_info.
Fixes: 8f0aad6f35 ("openvswitch: Extend packet attribute for egress tunnel info")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce helper function do_sock_sendmsg() to simplify sock_sendmsg{_nosec},
and replace reduplicate code.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 2b4636a5f8 ("tcp_cubic: make the delay threshold of HyStart
less sensitive"), HYSTART_DELAY_MIN was changed to 4 ms.
The remaining problem is that using delay_min + (delay_min/16) as the
threshold is too sensitive.
6.25 % of variation is too small for rtt above 60 ms, which are not
uncommon.
Lets use 12.5 % instead (delay_min + (delay_min/8))
Tested:
80 ms RTT between peers, FQ/pacing packet scheduler on sender.
10 bulk transfers of 10 seconds :
nstat >/dev/null
for i in `seq 1 10`
do
netperf -H remote -- -k THROUGHPUT | grep THROUGHPUT
done
nstat | grep Hystart
With the 6.25 % threshold :
THROUGHPUT=20.66
THROUGHPUT=249.38
THROUGHPUT=254.10
THROUGHPUT=14.94
THROUGHPUT=251.92
THROUGHPUT=237.73
THROUGHPUT=19.18
THROUGHPUT=252.89
THROUGHPUT=21.32
THROUGHPUT=15.58
TcpExtTCPHystartTrainDetect 2 0.0
TcpExtTCPHystartTrainCwnd 4756 0.0
TcpExtTCPHystartDelayDetect 5 0.0
TcpExtTCPHystartDelayCwnd 180 0.0
With the 12.5 % threshold
THROUGHPUT=251.09
THROUGHPUT=247.46
THROUGHPUT=250.92
THROUGHPUT=248.91
THROUGHPUT=250.88
THROUGHPUT=249.84
THROUGHPUT=250.51
THROUGHPUT=254.15
THROUGHPUT=250.62
THROUGHPUT=250.89
TcpExtTCPHystartTrainDetect 1 0.0
TcpExtTCPHystartTrainCwnd 3175 0.0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deploying FQ pacing, one thing we noticed is that CUBIC Hystart
triggers too soon.
Having SNMP counters to have an idea of how often the various Hystart
methods trigger is useful prior to any modifications.
This patch adds SNMP counters tracking, how many time "ack train" or
"Delay" based Hystart triggers, and cumulative sum of cwnd at the time
Hystart decided to end SS (Slow Start)
myhost:~# nstat -a | grep Hystart
TcpExtTCPHystartTrainDetect 9 0.0
TcpExtTCPHystartTrainCwnd 20650 0.0
TcpExtTCPHystartDelayDetect 10 0.0
TcpExtTCPHystartDelayCwnd 360 0.0
->
Train detection was triggered 9 times, and average cwnd was
20650/9=2294,
Delay detection was triggered 10 times and average cwnd was 36
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is never called and implementations are void. So just remove it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 908344cdda ("tipc: fix bug in multicast congestion
handling") introduced two bugs with the bclink wakeup
function. This commit fixes the missing spinlock init for the
waiting_sks list. We also eliminate the race condition
between the waiting_sks length check/dequeue operations in
tipc_bclink_wakeup_users by simply removing the redundant
length check.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Acked-by: Tero Aho <Tero.Aho@coriant.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ce1a4ea3f1 ("net: avoid one atomic operation in skb_clone()")
took the wrong way to save one atomic operation.
It is actually possible to avoid two atomic operations, if we
do not change skb->fclone values, and only rely on clone_ref
content to signal if the clone is available or not.
skb_clone() can simply use the fast clone if clone_ref is 1.
kfree_skbmem() can avoid the atomic_dec_and_test() if clone_ref is 1.
Note that because we usually free the clone before the original skb,
this particular attempt is only done for the original skb to have better
branch prediction.
SKB_FCLONE_FREE is removed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Chris Mason <clm@fb.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Shewmaker <agshew@gmail.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 56bfa7ee7c ("unregister_netdevice : move RTM_DELLINK to
until after ndo_uninit") tried to do this ealier but while doing so
it created a problem. Unfortunately the delayed rtmsg_ifinfo() also
delayed call to fill_info(). So this translated into asking driver
to remove private state and then query it's private state. This
could have catastropic consequences.
This change breaks the rtmsg_ifinfo() into two parts - one takes the
precise snapshot of the device by called fill_info() before calling
the ndo_uninit() and the second part sends the notification using
collected snapshot.
It was brought to notice when last link is deleted from an ipvlan device
when it has free-ed the port and the subsequent .fill_info() call is
trying to get the info from the port.
kernel: [ 255.139429] ------------[ cut here ]------------
kernel: [ 255.139439] WARNING: CPU: 12 PID: 11173 at net/core/rtnetlink.c:2238 rtmsg_ifinfo+0x100/0x110()
kernel: [ 255.139493] Modules linked in: ipvlan bonding w1_therm ds2482 wire cdc_acm ehci_pci ehci_hcd i2c_dev i2c_i801 i2c_core msr cpuid bnx2x ptp pps_core mdio libcrc32c
kernel: [ 255.139513] CPU: 12 PID: 11173 Comm: ip Not tainted 3.18.0-smp-DEV #167
kernel: [ 255.139514] Hardware name: Intel RML,PCH/Ibis_QC_18, BIOS 1.0.10 05/15/2012
kernel: [ 255.139515] 0000000000000009 ffff880851b6b828 ffffffff815d87f4 00000000000000e0
kernel: [ 255.139516] 0000000000000000 ffff880851b6b868 ffffffff8109c29c 0000000000000000
kernel: [ 255.139518] 00000000ffffffa6 00000000000000d0 ffffffff81aaf580 0000000000000011
kernel: [ 255.139520] Call Trace:
kernel: [ 255.139527] [<ffffffff815d87f4>] dump_stack+0x46/0x58
kernel: [ 255.139531] [<ffffffff8109c29c>] warn_slowpath_common+0x8c/0xc0
kernel: [ 255.139540] [<ffffffff8109c2ea>] warn_slowpath_null+0x1a/0x20
kernel: [ 255.139544] [<ffffffff8150d570>] rtmsg_ifinfo+0x100/0x110
kernel: [ 255.139547] [<ffffffff814f78b5>] rollback_registered_many+0x1d5/0x2d0
kernel: [ 255.139549] [<ffffffff814f79cf>] unregister_netdevice_many+0x1f/0xb0
kernel: [ 255.139551] [<ffffffff8150acab>] rtnl_dellink+0xbb/0x110
kernel: [ 255.139553] [<ffffffff8150da90>] rtnetlink_rcv_msg+0xa0/0x240
kernel: [ 255.139557] [<ffffffff81329283>] ? rhashtable_lookup_compare+0x43/0x80
kernel: [ 255.139558] [<ffffffff8150d9f0>] ? __rtnl_unlock+0x20/0x20
kernel: [ 255.139562] [<ffffffff8152cb11>] netlink_rcv_skb+0xb1/0xc0
kernel: [ 255.139563] [<ffffffff8150a495>] rtnetlink_rcv+0x25/0x40
kernel: [ 255.139565] [<ffffffff8152c398>] netlink_unicast+0x178/0x230
kernel: [ 255.139567] [<ffffffff8152c75f>] netlink_sendmsg+0x30f/0x420
kernel: [ 255.139571] [<ffffffff814e0b0c>] sock_sendmsg+0x9c/0xd0
kernel: [ 255.139575] [<ffffffff811d1d7f>] ? rw_copy_check_uvector+0x6f/0x130
kernel: [ 255.139577] [<ffffffff814e11c9>] ? copy_msghdr_from_user+0x139/0x1b0
kernel: [ 255.139578] [<ffffffff814e1774>] ___sys_sendmsg+0x304/0x310
kernel: [ 255.139581] [<ffffffff81198723>] ? handle_mm_fault+0xca3/0xde0
kernel: [ 255.139585] [<ffffffff811ebc4c>] ? destroy_inode+0x3c/0x70
kernel: [ 255.139589] [<ffffffff8108e6ec>] ? __do_page_fault+0x20c/0x500
kernel: [ 255.139597] [<ffffffff811e8336>] ? dput+0xb6/0x190
kernel: [ 255.139606] [<ffffffff811f05f6>] ? mntput+0x26/0x40
kernel: [ 255.139611] [<ffffffff811d2b94>] ? __fput+0x174/0x1e0
kernel: [ 255.139613] [<ffffffff814e2129>] __sys_sendmsg+0x49/0x90
kernel: [ 255.139615] [<ffffffff814e2182>] SyS_sendmsg+0x12/0x20
kernel: [ 255.139617] [<ffffffff815df092>] system_call_fastpath+0x12/0x17
kernel: [ 255.139619] ---[ end trace 5e6703e87d984f6b ]---
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reported-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of the old remote management feature is a piece of code
that checked permissions on the local system to see if a certain
operation was permitted, and if so pass the command to a remote
node. This serves no purpose after the removal of remote management
with commit 5902385a24 ("tipc: obsolete the remote management
feature") so we remove it.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To accomodate for enough headroom for tunnels, use MAX_HEADER instead
of LL_MAX_HEADER. Robert reported that he has hit after roughly 40hrs
of trinity an skb_under_panic() via SCTP output path (see reference).
I couldn't reproduce it from here, but not using MAX_HEADER as elsewhere
in other protocols might be one possible cause for this.
In any case, it looks like accounting on chunks themself seems to look
good as the skb already passed the SCTP output path and did not hit
any skb_over_panic(). Given tunneling was enabled in his .config, the
headroom would have been expanded by MAX_HEADER in this case.
Reported-by: Robert Święcki <robert@swiecki.net>
Reference: https://lkml.org/lkml/2014/12/1/507
Fixes: 594ccc14df ("[SCTP] Replace incorrect use of dev_alloc_skb with alloc_skb in sctp_packet_transmit().")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xchg is atomic, so there is no necessary to use spin_lock/spin_unlock
to protect it. At last, remove the redundant
opt = xchg(&inet6_sk(sk)->opt, opt); statement.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nice kernel helper to escape a given strings by provided rules. Let's
use it instead of custom approach.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[bfields@redhat.com: fix length calculation]
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
...move the WARN_ON_ONCE inside the following if block since they use
the same condition.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
These were useful when I was tracking down a race condition between
svc_xprt_do_enqueue and svc_get_next_xprt.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Testing has shown that the pool->sp_lock can be a bottleneck on a busy
server. Every time data is received on a socket, the server must take
that lock in order to dequeue a thread from the sp_threads list.
Address this problem by eliminating the sp_threads list (which contains
threads that are currently idle) and replacing it with a RQ_BUSY flag in
svc_rqst. This allows us to walk the sp_all_threads list under the
rcu_read_lock and find a suitable thread for the xprt by doing a
test_and_set_bit.
Note that we do still have a potential atomicity problem however with
this approach. We don't want svc_xprt_do_enqueue to set the
rqst->rq_xprt pointer unless a test_and_set_bit of RQ_BUSY returned
zero (which indicates that the thread was idle). But, by the time we
check that, the bit could be flipped by a waking thread.
To address this, we acquire a new per-rqst spinlock (rq_lock) and take
that before doing the test_and_set_bit. If that returns false, then we
can set rq_xprt and drop the spinlock. Then, when the thread wakes up,
it must set the bit under the same spinlock and can trust that if it was
already set then the rq_xprt is also properly set.
With this scheme, the case where we have an idle thread no longer needs
to take the highly contended pool->sp_lock at all, and that removes the
bottleneck.
That still leaves one issue: What of the case where we walk the whole
sp_all_threads list and don't find an idle thread? Because the search is
lockess, it's possible for the queueing to race with a thread that is
going to sleep. To address that, we queue the xprt and then search again.
If we find an idle thread at that point, we can't attach the xprt to it
directly since that might race with a different thread waking up and
finding it. All we can do is wake the idle thread back up and let it
attempt to find the now-queued xprt.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Tested-by: Chris Worley <chris.worley@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
In a later patch, we'll be removing some spinlocking around the socket
and thread queueing code in order to fix some contention problems. At
that point, the stats counters will no longer be protected by the
sp_lock.
Change the counters to atomic_long_t fields, except for the
"sockets_queued" counter which will still be manipulated under a
spinlock.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Tested-by: Chris Worley <chris.worley@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
...also make the manipulation of sp_all_threads list use RCU-friendly
functions.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Tested-by: Chris Worley <chris.worley@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Currently all svc_create callers pass in NULL for the shutdown parm,
which then gets fixed up to be svc_rpcb_cleanup if the service uses
rpcbind.
Simplify this by instead having the the only caller that requires it
(lockd) pass in svc_rpcb_cleanup and get rid of the special casing.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The way that svc_wake_up works is a bit inefficient. It walks all of the
available pools for a service and either wakes up a task in each one or
sets the SP_TASK_PENDING flag in each one.
When svc_wake_up is called, there is no need to wake up more than one
thread to do this work. In practice, only lockd currently uses this
function and it's single threaded anyway. Thus, this just boils down to
doing a wake up of a thread in pool 0 or setting a single flag.
Eliminate the for loop in this function and change it to just operate on
pool 0. Also update the comments that sit above it and get rid of some
code that has been commented out for years now.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
In a later patch, we'll want to be able to handle this flag without
holding the sp_lock. Change this field to an unsigned long flags
field, and declare a new flag in it that can be managed with atomic
bitops.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
In a later patch, we're going to need some atomic bit flags. Since that
field will need to be an unsigned long, we mitigate that space
consumption by migrating some other bitflags to the new field. Start
with the rq_secure flag.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Highlights include:
Features:
- NFSv4.2 client support for hole punching and preallocation.
- Further RPC/RDMA client improvements.
- Add more RPC transport debugging tracepoints.
- Add RPC debugging tools in debugfs.
Bugfixes:
- Stable fix for layoutget error handling
- Fix a change in COMMIT behaviour resulting from the recent io code updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wOP3
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.19-1' into nfsd for-3.19 branch
Mainly what I need is 860a0d9e51 "sunrpc: add some tracepoints in
svc_rqst handling functions", which subsequent server rpc patches from
jlayton depend on. I'm merging this later tag on the assumption that's
more likely to be a tested and stable point.
This merely fixes sparse warnings, without actually
adding support for the new APIs.
Still working out the best way to enable the new
functionality.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
net/bluetooth/smp.c:2650:9-16: WARNING: ERR_CAST can be used with tfm_aes
Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...))
Generated by: scripts/coccinelle/api/err_cast.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2014-12-03
1) Fix a set but not used warning. From Fabian Frederick.
2) Currently we make sequence number values available to userspace
only if we use ESN. Make the sequence number values also available
for non ESN states. From Zhi Ding.
3) Remove socket policy hashing. We don't need it because socket
policies are always looked up via a linked list. From Herbert Xu.
4) After removing socket policy hashing, we can use __xfrm_policy_link
in xfrm_policy_insert. From Herbert Xu.
5) Add a lookup method for vti6 tunnels with wildcard endpoints.
I forgot this when I initially implemented vti6.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the set/get_rxfh ethtool-options for getting or
setting the RSS hash function.
It modifies drivers implementation of set/get_rxfh accordingly.
This change also delegates the responsibility of checking whether a
modification to a certain RX flow hash parameter is supported to the
driver implementation of set_rxfh.
User-kernel API is done through the new hfunc bitmask field in the
ethtool_rxfh struct. A bit set in the hfunc field is corresponding to an
index in the new string-set ETH_SS_RSS_HASH_FUNCS.
Got approval from most of the relevant driver maintainers that their
driver is using Toeplitz, and for the few that didn't answered, also
assumed it is Toeplitz.
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Shradha Shah <sshah@solarflare.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
since head->handle == handle (checked before), just assign handle.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rcu variant is not correct here. The code is called by updater (rtnl
lock is held), not by reader (no rcu_read_lock is held).
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
rcu variant is not correct here. The code is called by updater (rtnl
lock is held), not by reader (no rcu_read_lock is held).
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
ACKed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert tipc name table read-write lock to RCU. After this change,
a new spin lock is used to protect name table on write side while
RCU is applied on read side.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a list_head variable is seen as a new entry to be added to a
list head, it's unnecessary to be initialized with INIT_LIST_HEAD().
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tipc name sequence is published, name table lock is released
before name sequence buffer is delivered to remote nodes through its
underlying unicast links. However, when name sequence is withdrawn,
the name table lock is held until the transmission of the removal
message of name sequence is finished. During the process, node lock
is nested in name table lock. To prevent node lock from being nested
in name table lock, while withdrawing name, we should adopt the same
locking policy of publishing name sequence: name table lock should
be released before message is sent.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As tipc_nametbl_lock is used to protect name_table structure, the lock
must be held while all members of name_table structure are accessed.
However, the lock is not obtained while a member of name_table
structure - local_publ_count is read in tipc_nametbl_publish(), as
a consequence, an inconsistent value of local_publ_count might be got.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC internally created a name table which is used to store name
sequences. Now there is a read-write lock - tipc_nametbl_lock to
protect the table, and each name sequence saved in the table is
protected with its private lock. When a name sequence is inserted
or removed to or from the table, its members might need to change.
Therefore, in normal case, the two locks must be held while TIPC
operates the table. However, there are still several places where
we only hold tipc_nametbl_lock without proprerly obtaining name
sequence lock, which might cause the corruption of name sequence.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As TIPC subscriber server is terminated before name table, no user
depends on subscription list of name sequence when name table is
stopped. Therefore, all name sequences stored in name table should
be released whatever their subscriptions lists are empty or not,
otherwise, memory leak might happen.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Name table locking policy is going to be adjusted from read-write
lock protection to RCU lock protection in the future commits. But
its essential precondition is to convert the allocation way of name
table from static to dynamic mode.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size variable is introduced in publ_list struct to help us exactly
calculate SKB buffer sizes needed by publications when all publications
in name table are delivered in bulk in named_distribute(). But if
publication SKB buffer size is assumed to MTU, the size variable in
publ_list struct can be completely eliminated at the cost of wasting
a bit memory space for last SKB.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Tero Aho <tero.aho@coriant.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The compute_score functions are a bit difficult to read.
Neaten them a bit to reduce object sizes and make them a
bit more intelligible.
Return early to avoid indentation and avoid unnecessary
initializations.
(allyesconfig, but w/ -O2 and no profiling)
$ size net/ipv[46]/udp.o.*
text data bss dec hex filename
28680 1184 25 29889 74c1 net/ipv4/udp.o.new
28756 1184 25 29965 750d net/ipv4/udp.o.old
17600 1010 2 18612 48b4 net/ipv6/udp.o.new
17632 1010 2 18644 48d4 net/ipv6/udp.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow reading of timestamps and cmsg at the same time on all relevant
socket families. One use is to correlate timestamps with egress
device, by asking for cmsg IP_PKTINFO.
on AF_INET sockets, call the relevant function (ip_cmsg_recv). To
avoid changing legacy expectations, only do so if the caller sets a
new timestamping flag SOF_TIMESTAMPING_OPT_CMSG.
on AF_INET6 sockets, IPV6_PKTINFO and all other recv cmsg are already
returned for all origins. only change is to set ifindex, which is
not initialized for all error origins.
In both cases, only generate the pktinfo message if an ifindex is
known. This is not the case for ACK timestamps.
The difference between the protocol families is probably a historical
accident as a result of the different conditions for generating cmsg
in the relevant ip(v6)_recv_error function:
ipv4: if (serr->ee.ee_origin == SO_EE_ORIGIN_ICMP) {
ipv6: if (serr->ee.ee_origin != SO_EE_ORIGIN_LOCAL) {
At one time, this was the same test bar for the ICMP/ICMP6
distinction. This is no longer true.
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
Changes
v1 -> v2
large rewrite
- integrate with existing pktinfo cmsg generation code
- on ipv4: only send with new flag, to maintain legacy behavior
- on ipv6: send at most a single pktinfo cmsg
- on ipv6: initialize fields if not yet initialized
The recv cmsg interfaces are also relevant to the discussion of
whether looping packet headers is problematic. For v6, cmsgs that
identify many headers are already returned. This patch expands
that to v4. If it sounds reasonable, I will follow with patches
1. request timestamps without payload with SOF_TIMESTAMPING_OPT_TSONLY
(http://patchwork.ozlabs.org/patch/366967/)
2. sysctl to conditionally drop all timestamps that have payload or
cmsg from users without CAP_NET_RAW.
Signed-off-by: David S. Miller <davem@davemloft.net>
One line change, in response to catching an occurrence of this bug.
See also fix f4713a3dfa ("net-timestamp: make tcp_recvmsg call ...")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* device-properties:
leds: leds-gpio: Fix multiple instances registration without 'label' property
leds: leds-gpio: Fix legacy GPIO number case
ACPI / property: Drop size_prop from acpi_dev_get_property_reference()
leds: leds-gpio: Convert gpio_blink_set() to use GPIO descriptors
ACPI / GPIO: Document ACPI GPIO mappings API
net: rfkill: gpio: Add default GPIO driver mappings for ACPI
ACPI / GPIO: Driver GPIO mappings for ACPI GPIOs
input: gpio_keys_polled: Make use of device property API
leds: leds-gpio: Make use of device property API
gpio: Support for unified device properties interface
Driver core: Unified interface for firmware node properties
input: gpio_keys_polled: Add support for GPIO descriptors
leds: leds-gpio: Add support for GPIO descriptors
gpio: sch: Consolidate core and resume banks
gpio / ACPI: Add support for _DSD device properties
misc: at25: Make use of device property API
ACPI: Allow drivers to match using Device Tree compatible property
Driver core: Unified device properties interface for platform firmware
ACPI: Add support for device specific properties
When the host decides to use a non-resolvable private address, it
must ensure that this generated address does not match the public
address of the controller. Add an extra check to ensure this required
behavior.
In addition rename the variable from urpa to nrpa and fix all of the
comments in the code that use the term unresolvable instead of the
term non-resolvable as used in the Bluetooth specification.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fix various spelling errors in the comments of the CAN modules.
Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Several CAN modules use a design pattern with a banner[] variable at the
top which defines a string that is used once during init to print the
banner. The string is also embedded with KERN_INFO which makes it
printk() specific.
Improve the code by eliminating the banner[] variable and moving the
string to where it is printed. Then switch from printk(KERN_INFO to
pr_info() for the lines that were changed.
Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The SMP over BR/EDR requests for cross-transport pairing should also
accepted when the debugfs setting force_lesc_support has been enabled.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The SMP over BR/EDR support for cross-transport pairing should also be
enabled when the debugfs setting force_lesc_support has been enabled.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
introduce new setsockopt() command:
setsockopt(sock, SOL_SOCKET, SO_ATTACH_BPF, &prog_fd, sizeof(prog_fd))
where prog_fd was received from syscall bpf(BPF_PROG_LOAD, attr, ...)
and attr->prog_type == BPF_PROG_TYPE_SOCKET_FILTER
setsockopt() calls bpf_prog_get() which increments refcnt of the program,
so it doesn't get unloaded while socket is using the program.
The same eBPF program can be attached to multiple sockets.
User task exit automatically closes socket which calls sk_filter_uncharge()
which decrements refcnt of eBPF program
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch fixes typo in the flow validation. This prevented
installation of ARP and IPv6 flows.
Fixes: 19e7a3df72 ("openvswitch: Fix NDP flow mask validation")
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the inner mac header to point to the GRE payload when
doing GRO. This is needed if we proceed to send the packet
through GRE GSO which now uses the inner mac header instead
of inner network header to determine the length of encapsulation
headers.
Fixes: 14051f0452 ("gre: Use inner mac length when computing tunnel length")
Reported-by: Wolfgang Walter <linux@stwm.de>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following batch contains netfilter updates for net-next. Basically,
enhancements for xt_recent, skip zeroing of timer in conntrack, fix
linking problem with recent redirect support for nf_tables, ipset
updates and a couple of cleanups. More specifically, they are:
1) Rise maximum number per IP address to be remembered in xt_recent
while retaining backward compatibility, from Florian Westphal.
2) Skip zeroing timer area in nf_conn objects, also from Florian.
3) Inspect IPv4 and IPv6 traffic from the bridge to allow filtering using
using meta l4proto and transport layer header, from Alvaro Neira.
4) Fix linking problems in the new redirect support when CONFIG_IPV6=n
and IP6_NF_IPTABLES=n.
And ipset updates from Jozsef Kadlecsik:
5) Support updating element extensions when the set is full (fixes
netfilter bugzilla id 880).
6) Fix set match with 32-bits userspace / 64-bits kernel.
7) Indicate explicitly when /0 networks are supported in ipset.
8) Simplify cidr handling for hash:*net* types.
9) Allocate the proper size of memory when /0 networks are supported.
10) Explicitly add padding elements to hash:net,net and hash:net,port,
because the elements must be u32 sized for the used hash function.
Jozsef is also cooking ipset RCU conversion which should land soon if
they reach the merge window in time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the LE Read Local P-256 Public Key command is supported, then
enable its corresponding complete event. And when the LE Generate DHKey
command is supported, enable its corresponding complete event as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The new Extended Scanner Filter Policies feature has to be enabled by
selecting the correct filter policy for the scan parameters. This
patch does that when the controller has been enabled to use LE Privacy.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the controller sends a LE Direct Advertising Report event, the host
must confirm that the resolvable random address provided matches with
its own identity resolving key. If it does, then that advertising report
needs to be processed. If it does not match, the report needs to be
ignored.
This patch adds full support for handling these new reports and using
them for device discovery and connection handling. This means when a
Bluetooth controller supports the Extended Scanner Filter Policies, it
is possible to use directed advertising with LE privacy.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the controller supports the Extended Scanner Filter Policies, it
supports the LE Direct Advertising Report event. However by default
that event is blocked by the LE event mask. It is required to enable
it during controller setup.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When using Start Service Discovery and when background scanning is used
to report devices, the RSSI is reported or the value 127 is provided in
case RSSI in unavailable.
For Start Discovery the value 0 is reported to keep backwards
compatibility with the existing users.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When no RSSI value is available then make sure that the result is
filtered out when the RSSI threshold filter is active.
This means that all Bluetooth 1.1 or earlier devices will not
report any results when using a RSSI threshold filter.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The mgmt.c file already has a bluetooth_base_uuid variable which has the
exact same value as the reverse_base_uuid one. This patch removes the
redundant variable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes the Get Connection Information mgmt command to take
advantage of the new cmd_complete callback. This allows for great
simplifications in the logic for constructing the cmd_complete event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we create the hci_conn object we should properly initialize the
RSSI to HCI_RSSI_INVALID.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch converts the Get Clock Information mgmt command to take
advantage of the new cmd_complete callback for pending commands.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch converts the Start/Stop Discovery mgmt commands to use the
cmd_complete callback of struct pending_cmd. Since both of these
commands return the same parameters as they take as input we can use the
existing generic_cmd_complete() helper for this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch updates the Unpair Device code to take advantage of the
cmd_complete callback of struct pending_cmd.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch converts the Pair Device mgmt command to use the new
cmd_complete callback for pending mgmt commands. The already existing
pairing_complete() function is exactly what's needed and doesn't need
changing.
In addition to getting the return parameters always right this patch
actually fixes a reference counting bug and memory leak with the
hci_conn that's attached to the pending mgmt command - something that
would occur when powering off or unplugging the adapter while pairing is
in progress.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch converts the user confirmation & PIN code mgmt commands to
take advantage of the new cmd_complete callback for pending mgmt
commands. The patch also adds a new generic addr_cmd_complete() helper
function to be used with commands that send a mgmt_addr_info response
based on a mgmt_addr_info in the beginning of the command parameters.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch converts the Disconnect mgmt command to take advantage of the
new cmd_complete callback that's part of the pending_cmd struct. There
are many commands whose response parameters map 1:1 to the command
parameters and Disconnect is one of them. This patch adds a
generic_cmd_complete() function for such commands that can be reused in
subsequent patches.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As preparation for making generic cmd_complete responses possible we'll
need to track the parameter length in addition to just a pointer to
them. This patch adds the necessary variable to the pending_cmd struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We've got a couple of generic scenarios where all pending mgmt commands
are processed and responses are sent to them. These scenarios are
powering off the adapter and removing the adapter. So far the code has
been generating cmd_status responses with NOT_POWERED and INVALID_INDEX
resposes respectively, but this violates the mgmt specification for
commands that should always generate a cmd_complete.
This patch adds support for specifying a callback for the pending_cmd
context that each command handler can use for command-specific
cmd_complete event generation. The actual per-command event generators
will come in subsequent patches.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some have been missing and some have been needed. Just cosmetics.
Signed-off-by: Stefan Schmidt <s.schmidt@samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Follow coding style of the kernel.
Signed-off-by: Stefan Schmidt <s.schmidt@samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This might change and we already deliver a copy of the license with
the kernel. This was already removed form the ieee802154 code but
missed here.
Signed-off-by: Stefan Schmidt <s.schmidt@samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the discovery filter information are only cleared when the
actual discovery procedure has been stopped. To make sure that none
of the filters interfere with the background scanning and its device
found event reporting, clear the filter before starting background
scanning.
This means that the discovery filter is now cleared before either
Start Discovery, Start Service Discovery or background scanning.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case of failure or when unplugging a controller, the allocated
memory for the UUID list of the discovery filter is not freed. Use
the newly introduced helper for reset the discovery filter and with
that also freeing existing memory.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The discovery filter allocates memory for its UUID list. So use
a helper function to free it and reset it to default states.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds support for the Start Service Discovery command. It
does all the checks for command parameters and configured the discovery
filter settings correctly. However the actual support for filtering
will be added with another patch.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The previous patch provided the framework for integrating the UUID
filtering into the service discovery. This patch now provides the
actual filter logic.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Using Start Service Discovery provides the option to specifiy a list
of UUID that are used to filter out device found events. This patch
provides the framework for hooking up the UUID filter.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Using Start Service Discovery allows to provide a RSSI threshold. This
patch implements support for filtering out device found events based
on the provided value.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the upcoming addition of support for Start Service Discovery, the
discovery handling needs to filter on RSSI and UUID values. For that
they need to be stored in the discovery handling. This patch adds the
appropiate fields and also make sure they are reset when discovery
has been stopped.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
a) make get_proc_ns() return a pointer to struct ns_common
b) mirror ns_ops in dentry->d_fsdata of ns dentries, so that
is_mnt_ns_file() could get away with fewer dereferences.
That way struct proc_ns becomes invisible outside of fs/proc/*.c
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
for now - just move corresponding ->proc_inum instances over there
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Johannes Berg <johannes@sipsolutions.net> says:
"This time I have Felix's no-status rate control work, which will allow
drivers to work better with rate control even if they don't have perfect
status reporting. In addition to this, a small hwsim fix from Patrik,
one of the regulatory patches from Arik, and a number of cleanups and
fixes I did myself.
Of note is a patch where I disable CFG80211_WEXT so that compatibility
is no longer selectable - this is intended as a wake-up call for anyone
who's still using it, and is still easily worked around (it's a one-line
patch) before we fully remove the code as well in the future."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the NFC pull request for 3.19.
With this one we get:
- NFC digital improvements for DEP support: Chaining, NACK and ATN
support added.
- NCI improvements: Support for p2p target, SE IO operand addition,
SE operands extensions to support proprietary implementations, and
a few fixes.
- NFC HCI improvements: OPEN_PIPE and NOTIFY_ALL_CLEARED support,
and SE IO operand addition.
- A bunch of minor improvements and fixes for STMicro st21nfcb and
st21nfca
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WHHp
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.19 pull request
This is the NFC pull request for 3.19.
With this one we get:
- NFC digital improvements for DEP support: Chaining, NACK and ATN
support added.
- NCI improvements: Support for p2p target, SE IO operand addition,
SE operands extensions to support proprietary implementations, and
a few fixes.
- NFC HCI improvements: OPEN_PIPE and NOTIFY_ALL_CLEARED support,
and SE IO operand addition.
- A bunch of minor improvements and fixes for STMicro st21nfcb and
st21nfca"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The actual process of compiling the correct HCI commands for triggering
discovery is something that should be generic. So instead of mixing it
into the Start Discover operation handling, split it out into its own
function utilizing HCI request handling and just providing status in
case of errors or invalid parameters.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Sending the required cmd_complete for the management commands should be
done in one place and not in multiple places. Especially for Start and
Stop Discovery commands this is split into to sending it in case of
failure from the complete handler, but in case of success from the
event state update function triggering mgmt_discovering. This is way
too convoluted and since hci_request serializes the HCI command
processing, send the cmd_complete response from the complete handler
for all cases.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Start Discovery command has some complicated code when it comes
to error handling. With the future introduction of Start Service
Discovery simplifying this makes it easier to read.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch increments the management interface revision due to the
addition of support for LE Secure Connection feature.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the addition of support for Bluetooth Low Energy Secure Connections
feature, it makes sense to increase the minor version of the Bluetooth
core module.
The module version is not used anywhere, but it gives a nice extra
hint for debugging purposes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some gcc versions don't seem to be able to properly track the flow of
the smp_cmd_pairing_random() function and end up causing the following
types of (false-positive) warnings:
smp.c:1995:6: warning: ‘nb’ may be used uninitialized in this function [-Wmaybe-uninitialized]
err = smp_g2(smp->tfm_cmac, pkax, pkbx, na, nb, &passkey);
smp.c:1995:6: warning: ‘na’ may be used uninitialized in this function [-Wmaybe-uninitialized]
err = smp_g2(smp->tfm_cmac, pkax, pkbx, na, nb, &passkey);
^
smp.c:1995:6: warning: ‘pkbx’ may be used uninitialized in this function [-Wmaybe-uninitialized]
err = smp_g2(smp->tfm_cmac, pkax, pkbx, na, nb, &passkey);
^
smp.c:1995:6: warning: ‘pkax’ may be used uninitialized in this function [-Wmaybe-uninitialized]
err = smp_g2(smp->tfm_cmac, pkax, pkbx, na, nb, &passkey);
This patch fixes the issue by moving the pkax/pkbx and na/nb
initialization earlier in the function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The convention for checking for NULL pointers is !ptr and not
ptr == NULL. This patch fixes such an occurrence in smp.c.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We need to keep debug keys around at least until the point that they are
used - otherwise e.g. slave role behavior wouldn't work as there'd be no
key to be looked up. The correct behavior should therefore be to return
any stored keys but when we clean up the SMP context to remove the key
from the hdev list if keeping debug keys around hasn't been requestsed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Linus Torvalds