Add support for RZ/G1E (R8A7745) SoC power areas to the R-Car SYSC driver.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ath.git patches for 4.10. Major changes:
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
"rockchip,hw-tshut-temp", "rockchip,hw-tshut-mode" and
"rockchip,hw-tshut-polarity" are not a required properties
actually as the code could also work by loading the default
settings there. So it is apprently misleading, although we
prefer to get these from DT. And it seems we miss the 'rockchip,grf'
here which should also be an optional property.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
The clock of IR can be provided by the clock provider and controlled
by common clock framework APIs.
Signed-off-by: Ruqiang Ju <juruqiang@huawei.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The internal codec on A23/A33/H3 is split into 2 parts. The
analog path controls are routed through an embedded custom register
bus accessed through the PRCM block.
The SoCs share a common set of inputs, outputs, and audio paths.
The following table lists the differences.
----------------------------------------
| Feature \ SoC | A23 | A33 | H3 |
----------------------------------------
| Headphone | v | v | |
----------------------------------------
| Line Out | | | v |
----------------------------------------
| Phone In/Out | v | v | |
----------------------------------------
Add a binding for this hardware.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
With the devices added to the tables, the probe will recognize the
switch. This however is not sufficient to make it work properly, other
changes are needed because of incompatibilities.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCA9632TK part seems to incorrectly blink at ~1.3x of the programmed
rate. This patchset add a nxp,period-scale devicetree property to
adjust for this misconfiguration.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYMhsfAAoJEHm+PkMAQRiGbZMH/AnSgpvWgJQGr/NsovAJsDM9
aJZPNQnjVD+6dBZLudCJOeKoZ8hd0vI/FNPxDrAJxt0L4PCX6Hxnmt+qsLAhodiU
uGOpLK7dwgE5OH3xEKzbEHJBitEZ5nmKBG1oEZNurL9kTFxyL78j7YnlMz/DpjsH
RwDfV4tD5vyVv8vcmHzo6OBWja+78Njo6+OVaMq/fw8+LqS2uq1ajsLWlkUMGo4b
3CDziy6lMLjHy5LlrWkxYvIK2ldB8o+3EDnp/KOwrQ/L9qNaBillUxwDI8qodqHV
NTUjBi51oqG06YwplJa7Qr9SVFD28SlNjVIv/PRgHm6kPfzNUvlp97WnWUn8R/8=
=SoWG
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rc6' into patchwork
Linux 4.9-rc6
* tag 'v4.9-rc6': (305 commits)
Linux 4.9-rc6
ext4: sanity check the block and cluster size at mount time
fscrypto: don't use on-stack buffer for key derivation
fscrypto: don't use on-stack buffer for filename encryption
i2c: i2c-mux-pca954x: fix deselect enabling for device-tree
kvm: x86: merge kvm_arch_set_irq and kvm_arch_set_irq_inatomic
KVM: x86: fix missed SRCU usage in kvm_lapic_set_vapic_addr
KVM: async_pf: avoid recursive flushing of work items
kvm: kvmclock: let KVM_GET_CLOCK return whether the master clock is in use
KVM: Disable irq while unregistering user notifier
KVM: x86: do not go through vcpu in __get_kvmclock_ns
MAINTAINERS: Add LED subsystem co-maintainer
crypto: algif_hash - Fix NULL hash crash with shash
powerpc/mm: Fix missing update of HID register on secondary CPUs
KVM: arm64: Fix the issues when guest PMCCFILTR is configured
arm64: KVM: pmu: Fix AArch32 cycle counter access
powerpc/mm/radix: Invalidate ERAT on tlbiel for POWER9 DD1
i2c: digicolor: use clk_disable_unprepare instead of clk_unprepare
ipmi/bt-bmc: change compatible node to 'aspeed, ast2400-ibt-bmc'
Revert "drm/mediatek: set vblank_disable_allowed to true"
...
other fixes.
In order to get the thermal node that we're adjusting the compatible
string on, we have to merge in the bcm2835-dt-next branch.
-----BEGIN PGP SIGNATURE-----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=zVOm
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=GHAx
-----END PGP SIGNATURE-----
Merge tag 'bcm2835-dt-64-next-2016-11-18' into devicetree-arm64/next
This pull request brings thermal support to the BCM2837 DT, and a few
other fixes.
In order to get the thermal node that we're adjusting the compatible
string on, we have to merge in the bcm2835-dt-next branch.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
- addition of missing documentation and DT properties for the CMU_AUD
block source clocks,
- correction of CMU_FSYS parent clock definition,
- marking as critical clocks which have to be enabled in order
to access control registers of child CMUs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oQKk
-----END PGP SIGNATURE-----
Merge tag 'clk-v4.10-exynos5433' of git://linuxtv.org/snawrocki/samsung into clk-next
Pull Exynos5433 SoC updates from Sylwester Nawrocki:
- addition of missing documentation and DT properties for the CMU_AUD
block source clocks,
- correction of CMU_FSYS parent clock definition,
- marking as critical clocks which have to be enabled in order
to access control registers of child CMUs.
* tag 'clk-v4.10-exynos5433' of git://linuxtv.org/snawrocki/samsung:
clk: exynos5433: Mark some clocks as critical
clk: exynos5433: Add documentation for the audio block parent clocks
clk: exynos5433: Fix parent clocks for FSYS block
RK1108 EVB is designed by Rockchip for CVR field.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
[split off from dts patch and to prevent conflicts with px5 addition]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
MSIOF in R-Car M3-W (r8a7796) is handled fine by the existing driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
DT binding for the TI DA8xx/OMAP-L1x/AM17xx/AM18xx MUSB driver.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ARM specifies that the system counter "must be implemented in an
always-on power domain," and so we try to use the counter as a source of
timekeeping across suspend/resume. Unfortunately, some SoCs (e.g.,
Rockchip's RK3399) do not keep the counter ticking properly when
switched from their high-power clock to the lower-power clock used in
system suspend. Support this quirk by adding a new device tree property.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add M3ULCB Device tree bindings Documentation, listing it as a supported
board.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This updates H3ULCB Device tree bindings Documentation with
official board name
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Driver can now work with both ID and VBUS pins or either one of
them.
There can be the following 3 cases
1) Both ID and VBUS GPIOs are available:
ID = LOW -> USB_HOST active, USB inactive
ID = HIGH -> USB_HOST inactive, USB state is same as VBUS.
2) Only ID GPIO is available:
ID = LOW -> USB_HOST active, USB inactive
ID = HIGH -> USB_HOST inactive, USB active
3) Only VBUS GPIO is available:
VBUS = LOW -> USB_HOST inactive, USB inactive
VBUS = HIGH -> USB_HOST inactive, USB active
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds documentation of device tree bindings for the STM32 ADC.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch derives device tree node from pcie bus layer framework.
Device tree bindings file has been renamed(marvell-sd8xxx.txt ->
marvell-8xxx.txt) to accommodate PCIe changes.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Contains two small patches, one fixing a typo and the other adding the
compatible string for the Denver CPUs found on the new Tegra186 SoCs.
-----BEGIN PGP SIGNATURE-----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=QQY8
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.10-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
dt-bindings: Cleanups and additions for v4.10-rc1
Contains two small patches, one fixing a typo and the other adding the
compatible string for the Denver CPUs found on the new Tegra186 SoCs.
* tag 'tegra-for-4.10-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: Add documentation for Tegra186 Denver
serial: tegra20-hsuart: Fix typo in dmas DT binding description
Signed-off-by: Olof Johansson <olof@lixom.net>
This provides a driver to enable the use of the Generic Memory Interface
found on Tegra SoCs that can host various types of high-speed devices.
-----BEGIN PGP SIGNATURE-----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=xCcZ
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.10-bus' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
bus: Add Tegra GMI support
This provides a driver to enable the use of the Generic Memory Interface
found on Tegra SoCs that can host various types of high-speed devices.
* tag 'tegra-for-4.10-bus' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
bus: Add support for Tegra Generic Memory Interface
dt/bindings: Add bindings for Tegra GMI controller
Signed-off-by: Olof Johansson <olof@lixom.net>
IVC is an inter-processor communication protocol that uses shared memory
to exchange data between processors. The BPMP driver makes use of this
to communicate with the Boot and Power Management Processor (BPMP) and
uses an additional hardware synchronization primitive from the HSP block
to signal availability of new data (doorbell).
Firmware running on the BPMP implements a number of services such as the
control of clocks and resets within the system, or the ability to ungate
or gate power partitions.
-----BEGIN PGP SIGNATURE-----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=9jQK
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.10-firmware' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
firmware: Add Tegra IVC and BPMP support
IVC is an inter-processor communication protocol that uses shared memory
to exchange data between processors. The BPMP driver makes use of this
to communicate with the Boot and Power Management Processor (BPMP) and
uses an additional hardware synchronization primitive from the HSP block
to signal availability of new data (doorbell).
Firmware running on the BPMP implements a number of services such as the
control of clocks and resets within the system, or the ability to ungate
or gate power partitions.
* tag 'tegra-for-4.10-firmware' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: firmware: Allow child nodes inside the Tegra BPMP
dt-bindings: Add power domains to Tegra BPMP firmware
firmware: tegra: Add BPMP support
firmware: tegra: Add IVC library
dt-bindings: firmware: Add bindings for Tegra BPMP
Signed-off-by: Olof Johansson <olof@lixom.net>
This contains the device tree bindings and a driver for the Tegra HSP, a
hardware block that provides hardware synchronization primitives and is
the foundation for inter-processor communication between CPU and BPMP.
-----BEGIN PGP SIGNATURE-----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=Gojp
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.10-mailbox' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
mailbox: Add Tegra HSP driver
This contains the device tree bindings and a driver for the Tegra HSP, a
hardware block that provides hardware synchronization primitives and is
the foundation for inter-processor communication between CPU and BPMP.
* tag 'tegra-for-4.10-mailbox' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
mailbox: tegra-hsp: Use after free in tegra_hsp_remove_doorbells()
mailbox: Add Tegra HSP driver
dt-bindings: mailbox: Add Tegra HSP binding
soc/tegra: Add Tegra186 support
Signed-off-by: Olof Johansson <olof@lixom.net>
* Basic support for r8a7745 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tBnV
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc2-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Second Round of Renesas ARM Based SoC Updates for v4.10
* Basic support for r8a7745 SoC
* tag 'renesas-soc2-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: document SK-RZG1E board
ARM: shmobile: r8a7745: basic SoC support
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add hwmod interconnect target wrapper module data for crypto
accelerators for am3xxx, am43xx and dra7
- Add support for dra71x family of SoCs
- PM fixes for omap4/5 needed for omap5 cpuidle
-----BEGIN PGP SIGNATURE-----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=hUTI
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.10/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
SoC changes for omaps for v4.10 merge window:
- Add hwmod interconnect target wrapper module data for crypto
accelerators for am3xxx, am43xx and dra7
- Add support for dra71x family of SoCs
- PM fixes for omap4/5 needed for omap5 cpuidle
* tag 'omap-for-v4.10/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: DRA7: hwmod: Do not register RTC on DRA71
ARM: OMAP2+: board-generic: add support for DRA71x family
ARM: AMx3xx: hwmod: Add data for RNG
ARM: AM43xx: hwmod: Add data for DES
ARM: OMAP: DRA7xx: Make L4SEC clock domain SWSUP only
ARM: DRA7: hwmod: Add data for RNG IP
ARM: DRA7: hwmod: Add data for SHA IP
ARM: DRA7: hwmod: Add data for AES IP
ARM: DRA7: hwmod: Add data for DES IP
ARM: OMAP5: Add basic cpuidle MPU CSWR support
ARM: OMAP4+: Fix bad fallthrough for cpuidle
ARM: OMAP5: Fix mpuss_early_init
ARM: OMAP5: Fix build for PM code
Signed-off-by: Olof Johansson <olof@lixom.net>
Support for the Allwinner A64, their first armv8 SoC.
-----BEGIN PGP SIGNATURE-----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=JkJ+
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt64
Allwinner arm64 DT changes for 4.10
Support for the Allwinner A64, their first armv8 SoC.
* tag 'sunxi-dt64-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
arm64: dts: add Pine64 support
Documentation: devicetree: add vendor prefix for Pine64
arm64: dts: add Allwinner A64 SoC .dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
- remove obsolete STiH41[56] platform support
- add Oxford Semiconductor OX820 support
- add reset index include files for OX810SE and OX820
- make drivers with boolean Kconfig options explicitly
non-modular
- allow shared pulsed resets via reset_control_reset, which
in this case means that the reset must have been triggered
once, but possibly earlier, after the function returns, and
is never triggered again for the lifetime of the reset
control
-----BEGIN PGP SIGNATURE-----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=e7kp
-----END PGP SIGNATURE-----
Merge tag 'reset-for-4.10' of git://git.pengutronix.de/git/pza/linux into next/drivers
Reset controller changes for v4.10
- remove obsolete STiH41[56] platform support
- add Oxford Semiconductor OX820 support
- add reset index include files for OX810SE and OX820
- make drivers with boolean Kconfig options explicitly
non-modular
- allow shared pulsed resets via reset_control_reset, which
in this case means that the reset must have been triggered
once, but possibly earlier, after the function returns, and
is never triggered again for the lifetime of the reset
control
* tag 'reset-for-4.10' of git://git.pengutronix.de/git/pza/linux:
reset: allow using reset_control_reset with shared reset
reset: lpc18xx: make it explicitly non-modular
reset: zynq: make it explicitly non-modular
reset: sunxi: make it explicitly non-modular
reset: socfpga: make it explicitly non-modular
reset: berlin: make it explicitly non-modular
dt-bindings: reset: oxnas: Update for OX820
dt-bindings: reset: oxnas: Add include file with reset indexes
reset: oxnas: Add OX820 support
reset: sti: softreset: Remove obsolete platforms from dt binding doc.
reset: sti: Remove STiH415/6 reset support
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYHmoCAAoJEHm+PkMAQRiG7RMIAI2i7Y5hpL5yCxK5AFaL4u/G
KxXfp1B1UanUTgjOmd7zGqtDYcFX9t7GTTUFixQ7/9Opr4PD9qbnatoDGSc3xjbT
msDgA1B78F1/Q3kHWfeGq32MihQ4mj5NwUCo+igUcUvvWG7mHgzErj/Nh5RoobQX
p/izdpTbrw3GX6xXB8olbG7XWHaVye/+TT3q6+gmgm8I/QEujcLeGoycE0zlhPN8
FG/JX76At/+ZM2Py7Oxo3k+oKL9CHrtOQYDp/wN0uslV5eYvvkZz0/M1HMOGZt+c
gZU5jzM17K7C4Nzo06WAuBU9wUBGc25m+cPicLlOmljnzfU+f50SKaDjZq3p7QI=
=2KUF
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rc4' into sound
Bring in -rc4 patches so I can successfully merge the sound doc changes.
- Correct the hardware pin number of the usb node on the Hip06
- Add the Hisilicon Hip07 D05 board dts binding
- Add the initial dts for the Hip07 D05 board
- Fix the warning for the node without reg propery on the Hip06
- Fix the sas am max transmissions quirk property on the Hip06
- Disable the sas0 and sas2 on D03 board
- Add refclk node for SAS on the Hip06
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MVHS
-----END PGP SIGNATURE-----
Merge tag 'hisi-arm64-dt-4.10' of git://github.com/hisilicon/linux-hisi into next/dt64
ARM64: DT: Hisilicon SoC DT updates for 4.10
- Correct the hardware pin number of the usb node on the Hip06
- Add the Hisilicon Hip07 D05 board dts binding
- Add the initial dts for the Hip07 D05 board
- Fix the warning for the node without reg propery on the Hip06
- Fix the sas am max transmissions quirk property on the Hip06
- Disable the sas0 and sas2 on D03 board
- Add refclk node for SAS on the Hip06
* tag 'hisi-arm64-dt-4.10' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hisi: add refclk node to hip06 dts files for SAS
arm64: dts: hisi: disable sas0 and sas2 for d03
arm64: dts: hisi: fix hip06 sas am-max-trans quirk
arm64: dts: hip06: Fix no reg property warning
arm64: dts: hisilicon: Add initial dts for Hip07 D05 board
Documentation: arm64: Add Hisilicon Hip07 D05 dts binding
arm64: dts: hip06: Correct hardware pin number of usb node
Signed-off-by: Olof Johansson <olof@lixom.net>
- Enable Thermal Monitoring Unit (TMU) for thermal management on
LS1043A and LS2080A.
- Add support for LS1046A SoC, which has similar peripherals as
LS1043A but integrates 4 A72 cores.
- Add two LS1046A based board support: LS1046A-QDS and LS1046A-RDB.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYKrk2AAoJEFBXWFqHsHzOQlwH+wQXK2WABTOjRVchLOzup/cD
UtB7mbmXJrBSePa3OTvF8xMk4VFfjm9oljmLnUEnzWEfjsS2aURT2GJBWv/ddhqw
Mg/fYcZ1LgzJq8VOnenLpF1L2jc/I2hivCkBNmmkMK0HQvURKEAsdqNDc7Zg0meY
64qokll9Uz4DM2yeHkrUs9Q13UPs9/88ikYbE+CVDFaI0TCJjZUTImmjYkt8pJyk
poDtW6yE8ibMNk2DK4e4tthPRcYnhkFOtSJF6Qy6jouV/J9+aaKG5+rj4MBeF8Aj
T2+RFSQ4s2BuI5cH3qQq8Fv7lvF0Ay4wNWZl420R7shjbPWQNdIcbAbKL+51De0=
=jiir
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt64
Freescale arm64 device tree updates for 4.10:
- Enable Thermal Monitoring Unit (TMU) for thermal management on
LS1043A and LS2080A.
- Add support for LS1046A SoC, which has similar peripherals as
LS1043A but integrates 4 A72 cores.
- Add two LS1046A based board support: LS1046A-QDS and LS1046A-RDB.
* tag 'imx-dt64-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: ls2080a: Add TMU device tree support for LS2080A
arm64: dts: ls1043a: Add TMU device tree support for LS1043A
arm64: dts: add LS1046A-QDS board support
Documentation: DT: Add entry for QorIQ LS1046A-QDS board
arm64: dts: add LS1046A-RDB board support
Documentation: DT: Add entry for QorIQ LS1046A-RDB board
arm64: dts: add QorIQ LS1046A SoC support
dt-bindings: ahci-fsl-qoriq: updated for SoC ls1046a
dt-bindings: qoriq-clock: add LS1043A/LS1046A/LS2080A compatible for clockgen
dt-bindings: i2c: adds two more nxp devices
dt-bindings: fsl: add LS1043A/LS1046A/LS2080A compatible for SCFG and DCFG
dt-bindings: fsl: Add LS1043A/LS1046A/LS2080A SoC compatible strings
Signed-off-by: Olof Johansson <olof@lixom.net>
- A series from Vladimir to fix broken i.MX31 DT clock initialization.
As i.MX31 DT support is still not quite complete, the changes are
tested on qemu kzm target and mx31lite board with simple written DTS
files.
- A fix for CompuLab's sbc-fx6 baseboard to remove wrong fec pinctrl
setting.
- A DTS correction for i.MX6QP to reflect the change that the gate of
LDB clock has been moved before the divider.
- An imx7d-pinfunc fix for UART pinmux defines
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYKoTwAAoJEFBXWFqHsHzOGyMH/03fFizPHl+LQYilR8hKbFLg
amAhmqVEM0gRv/yvBwi/I0FXUyoBY4rhhAzvjy+1eF23wlipXt+2FozlXLW3jy2w
YP1bTnSy3qN5+eZakfeARFDh7Q1ab/19ZBJYFyQaRB2yY3CRDz3xeY5mOeVHdnUb
jI1+GpDAr37acGlGVOrsYJlpNlzX8HjAfRhPvlEqMH1Xp/1O5EgkzHyICKR9ysaB
f7fDTAhVsxivdCF/XU6TpyOUtWshu0v4ji+JtvRkz0p+9gHgWGKzu9ixQTr1FFxZ
YHPnxpDf4jtygLtrrzT4qBww/84PemAfQ3Rhpl1aG9331VB962UZ3R+JDoSSwnE=
=Xqw0
-----END PGP SIGNATURE-----
Merge tag 'imx-fix-nc-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/fixes-non-critical
i.MX non-critical fixes for 4.10:
- A series from Vladimir to fix broken i.MX31 DT clock initialization.
As i.MX31 DT support is still not quite complete, the changes are
tested on qemu kzm target and mx31lite board with simple written DTS
files.
- A fix for CompuLab's sbc-fx6 baseboard to remove wrong fec pinctrl
setting.
- A DTS correction for i.MX6QP to reflect the change that the gate of
LDB clock has been moved before the divider.
- An imx7d-pinfunc fix for UART pinmux defines
* tag 'imx-fix-nc-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6q-cm-fx6: fix fec pinctrl
ARM: dts: imx7d-pinfunc: fix UART pinmux defines
ARM: dts: imx6qp: correct LDB clock inputs
ARM: clk: imx31: properly init clocks for machines with DT
clk: imx31: fix rewritten input argument of mx31_clocks_init()
ARM: dts: imx31: move CCM device node to AIPS2 bus devices
ARM: dts: imx31: fix clock control module interrupts description
Signed-off-by: Olof Johansson <olof@lixom.net>
Add bindings document for the Altera Freeze Bridge. A Freeze
Bridge is used to gate traffic to/from a region of a FPGA
such that that region can be reprogrammed. The Freeze Bridge
exist in FPGA fabric that is not currently being reconfigured.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Matthew Gerlach <mgerlach@opensource.altera.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a device tree bindings document for the SoCFPGA Arria10
FPGA Manager driver.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-By: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Rob Herring <robh@kernel.org>
us to use generic parser later on. Note that the driver supports
handling the legacy binding also with no #pinctrl-cells so these
changes can be queued separately from the driver changes.
-----BEGIN PGP SIGNATURE-----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=qXyV
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.10/pinctrl-cells-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Add #pinctrl-cells for pinctrl-single using dts files. This allows
us to use generic parser later on. Note that the driver supports
handling the legacy binding also with no #pinctrl-cells so these
changes can be queued separately from the driver changes.
* tag 'omap-for-v4.10/pinctrl-cells-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add #pinctrl-cells for pinctrl-single instances
Signed-off-by: Olof Johansson <olof@lixom.net>
- few fixes for the memory drivers
- minimal security module driver
- support for the Secure SRAM
-----BEGIN PGP SIGNATURE-----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=/UOn
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.10-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/drivers
Drivers for 4.10:
- few fixes for the memory drivers
- minimal security module driver
- support for the Secure SRAM
* tag 'at91-ab-4.10-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
misc: sram: add Atmel securam support
misc: sram: document new compatible
ARM: at91: add secumod register definitions
Documentation: dt: atmel-at91: Document secumod bindings
memory: atmel-sdramc: use builtin_platform_driver to simplify the code
memory: atmel-ebi: fix return value check in at91_ebi_dev_disable()
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'clk-qcom-8994' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: Add support for msm8994 global clock controller
dt-bindings: qcom: clocks: Add msm8994 clock bindings
Fix the no. of gpio cells in pxa gpio binding documentation.
The no. of gpio cells for the pxa gpio is actually 2. But is
incorrectly specified as 1, in the binding documentation. From the
driver code, the second cell specifies the standard flags as described
in gpio.txt.
Signed-off-by: Vijay Kumar B. <vijaykumar@zilogic.com>
[fixed subject line]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
-----BEGIN PGP SIGNATURE-----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=5WN9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.10 merge window
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
The BPMP implements some services which must be represented by separate
nodes. For example, it can provide access to certain I2C controllers,
and the I2C bindings represent each I2C controller as a device tree
node. Update the binding to describe how the BPMP supports this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
[treding@nvidia.com: renamed bpmp-i2c to i2c as per Rob]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra186 BPMP is also a provider of power domains. Enhance the
device tree binding to describe this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Boot and Power Management Processor (BPMP) is a co-processor found
in Tegra SoCs. It is designed to handle the early stages of the boot
process as well as to offload power management tasks (such as clocks,
resets, powergates, ...).
The binding document defines the resources that are used by the BPMP
firmware, which implements the interprocessor communication (IPC)
between the CPU and the BPMP.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The corresponding driver only supports the USB PHY on Meson8b and GXBB
SoCs. Newer SoC versions are using a different USB PHY implementation,
which will mean that a new driver is required. Thus make sure that our
naming is specific enough so it does not conflict with upcoming drivers.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Update the example so the node name uses a dash (instead of an
underscore) as per convention.
Additionally it updates the example register offset to a real example
(the old value was taken from a draft where there was an additional PHY
bus).
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for the "amcc,usb-otg" device
which is found in the PowerPC Canyonlands' dts.
The device definition was added by:
commit c89b3458d8 ("powerpc/44x: Add USB DWC DTS entry to Canyonlands
board")
but without any driver support as the dwc2 driver wasn't available at
that time.
Note: The system can't use the generic "snps,dwc2" compatible
because of the special ahbcfg configuration. The default
GAHBCFG_HBSTLEN_INCR4 of snps,dwc2 can cause a system hang
when the USB and SATA is used concurrently.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is not needed as the gadget now fully supports DMA and it can
autodetect it. This was initially added because gadget DMA mode was only
partially implemented so could not be automatically enabled.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
- Add clocks for auxadc on mt8173-evb
- Add nodes needed by clock controller for mt2701
- Use clocks from the clock controller for the uart of mt2701
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wFjD
-----END PGP SIGNATURE-----
Merge tag 'v4.9-next-dts' of https://github.com/mbgg/linux-mediatek into next/dt
- Add bindings for mtk-scpsys for mt2701
- Add clocks for auxadc on mt8173-evb
- Add nodes needed by clock controller for mt2701
- Use clocks from the clock controller for the uart of mt2701
* tag 'v4.9-next-dts' of https://github.com/mbgg/linux-mediatek:
arm: dts: mt2701: Use real clock for UARTs
arm: dts: mt2701: Add clock controller device nodes
arm64: dts: mt8173: Fix auxadc node
soc: mediatek: Add MT2701 power dt-bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
support for LCD found on DaVinci DA8xx devices.
They allow configuration of memory interface and
bus priorities on the SoC to allow sufficient
bandwidth for the LCD and prevent underruns.
The DT bindings have been reviewed by Rob and
patches have been reviewed by Kevin.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ye/f
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.10/drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
This pull request adds two new drivers for better
support for LCD found on DaVinci DA8xx devices.
They allow configuration of memory interface and
bus priorities on the SoC to allow sufficient
bandwidth for the LCD and prevent underruns.
The DT bindings have been reviewed by Rob and
patches have been reviewed by Kevin.
* tag 'davinci-for-v4.10/drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
bus: davinci: add support for da8xx bus master priority control
memory: davinci: add support for da8xx DDR2/mDDR controller
Signed-off-by: Olof Johansson <olof@lixom.net>
a fix for wrong i2c registers on rk3368 a new nvmem cell and
power-domain on rk3399 as well as moving mmc frequency
properties to the more generic max-frequency one.
-----BEGIN PGP SIGNATURE-----
iQEtBAABCAAXBQJYJzRqEBxoZWlrb0BzbnRlY2guZGUACgkQ86Z5yZzRHYE8HAgA
hFPUM6OmYsP81xJ8B8NscxZXi0r5ZTp14ouF5cREPF5mwXghrE5ZEGC/+xQJ/X4p
WSSGglNEJV5Ofs869wYDU3yZwNRzwkK7bGY+Mzq8eySYzkfZR2VZUf5ZStsLfUS1
j6Gr7jr2gwFtpjlwLmaUj8O4i/I3FfTiDLobqdpXoeoRcisLXS4/xDxEC1143TDR
ctylpGFEW/LXC1L4kTyLUZ6688654IC5qZBp4yHLIgb+qfd8k+CEjEyxtCzGpAQJ
sLQnsjjer4C3MqgOSDAjyguKpePCz0VIoE8wct136sQh20isbgWuhQjQ9+QzAaE+
/N+j0d87kaHUdPa097wQkg==
=LC5U
-----END PGP SIGNATURE-----
Merge tag 'v4.10-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
64bit devicetree changes including the px5 evaluation board
a fix for wrong i2c registers on rk3368 a new nvmem cell and
power-domain on rk3399 as well as moving mmc frequency
properties to the more generic max-frequency one.
* tag 'v4.10-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: replace to "max-frequency" instead of "clock-freq-min-max"
arm64: dts: rockchip: add cpu-id nvmem cell node for rk3399
arm64: dts: rockchip: add sdmmc support for px5-evb
arm64: dts: rockchip: Add more properties for emmc on px5-evb
arm64: dts: rockchip: Add PX5 Evaluation board
arm64: dts: rockchip: add powerdomain for typec on rk3399
arm64: dts: rockchip: fix i2c resource error of rk3368
Signed-off-by: Olof Johansson <olof@lixom.net>
inclusion, missing unit names for memory nodes, various frequency
optimizations allowing for better performance on rk3066, the usage of
pin constants to bridge between the two numbering schemes used (gpio
controllers using 0-31 and pins being labeled A0-A7,..., D0-D7)
and UHS/HS modes for the mmc controllers on the popmetal board.
Two new boards, the PX3-based evaluation board, with the PX3 being an
industrial variant of the rk3188 soc and the Rikomagic MK808 board
based around the rk3066 are also added.
-----BEGIN PGP SIGNATURE-----
iQEtBAABCAAXBQJYJzNfEBxoZWlrb0BzbnRlY2guZGUACgkQ86Z5yZzRHYGsQQf/
WWYA4/oR4pT8HMns5coctc2zOyNU8KYmaeRl7TViUna+HA6/m2SGMqomTFV2AK0v
Ha3M6A35dDUGJNmAbEB5oolGOwHh82gZKYxYIQiNX+zCxeb5JxKCXWSqAjC9Ndwu
h600H1K/Qb26OzaVE/ICtlveduN+9BWrlzNseHsm99Z93FNsRLN0Z8s2Mn3jra6P
2Pf1sJkOPuh47i/Y/gTDVcFSf6Srb4SM/26fiZjrRa8LaaO/0I2Ku34ne9FygGzi
0GBHWh2SILM297MZMcrCDoJvTTqLT05tUrX1PDGmdunqP8vnsOAgvL9291G8d4sw
PbYE3onlyoxHmeOSffAe5g==
=AXPK
-----END PGP SIGNATURE-----
Merge tag 'v4.10-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
32bit devicetree changes for Rockchip including removal of skeleton.dtsi
inclusion, missing unit names for memory nodes, various frequency
optimizations allowing for better performance on rk3066, the usage of
pin constants to bridge between the two numbering schemes used (gpio
controllers using 0-31 and pins being labeled A0-A7,..., D0-D7)
and UHS/HS modes for the mmc controllers on the popmetal board.
Two new boards, the PX3-based evaluation board, with the PX3 being an
industrial variant of the rk3188 soc and the Rikomagic MK808 board
based around the rk3066 are also added.
* tag 'v4.10-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (21 commits)
ARM: dts: rockchip: replace to "max-frequency" instead of "clock-freq-min-max"
ARM: dts: rockchip: Set sdmmc frequency at boot time for rk3066a
ARM: dts: rockchip: use pin constants to describe gpios on Popmetal-RK3288
include: dt-bindings: Add GPIO pin index definition for rockchip pinctrl
ARM: dts: rockchip: Add rk3066 MK808 board
devicetree: Add vendor prefix for Rikomagic
ARM: dts: rockchip: initialize rk3066 PLL clock rate
clk: rockchip: Add binding ids for cpu and peri clocks on rk3066
ARM: dts: rockchip: enable HS200/DDR52 mode for emmc on rk3288-popmetal
ARM: dts: rockchip: Support UHS mode for SD card on PopMetal-RK3288 board
ARM: dts: rockchip: remove always-on and boot-on from vcc_sd for px3-evb
ARM: dts: rockchip: update compatible strings for Rockchip efuse
ARM: dts: rockchip: add rockchip PX3 Evaluation board
ARM: dts: rockchip: Add missing unit name to memory nodes in rk3xxx boards
ARM: dts: rockchip: Add missing unit name to memory nodes in rk3288 boards
ARM: dts: rockchip: Add missing unit name to memory nodes in rk322x boards
ARM: dts: rockchip: Add missing unit name to memory nodes in rk3036 boards
ARM: dts: rockchip: Remove skeleton.dtsi inclusion in rk3xxx.dtsi
ARM: dts: rockchip: Remove skeleton.dtsi inclusion in rk3288.dtsi
ARM: dts: rockchip: Remove skeleton.dtsi inclusion in rk322x.dtsi
...
Signed-off-by: Olof Johansson <olof@lixom.net>
SoC along with two boards. A lot of Samsung people contributed into this
but the final work and commits were done by Chanwoo Choi.
This means that for v4.10 we got:
1. Exynos5433 DTSI.
2. Two boards: TM2 and TM2E. These are (almost fully) working mobile phones.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zbqq
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Finally, I am really pleased to announce adding support for Exynos5433 ARMv8
SoC along with two boards. A lot of Samsung people contributed into this
but the final work and commits were done by Chanwoo Choi.
This means that for v4.10 we got:
1. Exynos5433 DTSI.
2. Two boards: TM2 and TM2E. These are (almost fully) working mobile phones.
* tag 'samsung-dt64-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Add dts file for Exynos5433-based TM2E board
arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board
arm64: dts: exynos: Add dtsi files for Samsung Exynos5433 64bit SoC
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Add TOPEET itop core and Elite boards, based on Exynos4412.
2. Remove the Exynos4415 DTSI. We did not have any mainlined boards
using it. I am also not aware of any popular out-of-tree boards using it.
3. Add Snoop Control Unit node for Exynos4.
4. Minor cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qzwE
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DeviceTree update for v4.10:
1. Add TOPEET itop core and Elite boards, based on Exynos4412.
2. Remove the Exynos4415 DTSI. We did not have any mainlined boards
using it. I am also not aware of any popular out-of-tree boards using it.
3. Add Snoop Control Unit node for Exynos4.
4. Minor cleanups.
* tag 'samsung-dt-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add SCU device node to exynos4.dtsi
ARM: dts: exynos: Remove exynos4415.dtsi
ARM: dts: exynos: Document eMMC/SD/SDIO devices in Snow and Peach boards
ARM: dts: exynos: Add TOPEET itop elite based board
ARM: dts: exynos: Add TOPEET itop core board SCP package version
ARM: dts: exynos: Add entries for sound support on Odroid-XU board
ARM: dts: exynos: Remove "simple-bus" compatible from fimc-is node
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYFQwAAAoJEHm+PkMAQRiGr8YH/0urDFZm/RFu752rSawF7iVM
nx9Ck03YkRiMRZfdzPARbHJts7lhLG1rvsT50VQNMK1sVv0BXcrnJnDu49xV+dLj
DqXWvYGtdTCpAd34Am37pX/rrRl11vdJgS2VgprmbytkM8FD0xEe+aDKxnnmuALo
bggYDhMrJik3/UXG0zVfefKZJFLNAJiZv9AgWgkCR+bo861bu3UFn47tN1jGXOOl
QyFl5t7ggesojA5Q1U9hTrk1gS9Ia9it3Elyzfqb66lUdyf001I1nbUA/hNYyDXD
HU9dj3agvVXjvnDjyDR4/k86FA+EEEwSgk5CBTCVe30dLKnojFyb7FWZg72utg4=
=CHER
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rc3' into next/dt64
Linux 4.9-rc3
* tag 'v4.9-rc3': (292 commits)
Linux 4.9-rc3
x86/smpboot: Init apic mapping before usage
ACPICA: Dispatcher: Fix interpreter locking around acpi_ev_initialize_region()
ACPICA: Dispatcher: Fix an unbalanced lock exit path in acpi_ds_auto_serialize_method()
ACPICA: Dispatcher: Fix order issue of method termination
ARC: module: print pretty section names
ARC: module: elide loop to save reference to .eh_frame
ARC: mm: retire ARC_DBG_TLB_MISS_COUNT...
ARC: build: retire old toggles
ARC: boot log: refactor cpu name/release printing
ARC: boot log: remove awkward space comma from MMU line
ARC: boot log: don't assume SWAPE instruction support
ARC: boot log: refactor printing abt features not captured in BCRs
ARCv2: boot log: print IOC exists as well as enabled status
ubifs: Fix regression in ubifs_readdir()
ubi: fastmap: Fix add_vol() return value test in ubi_attach_fastmap()
MAINTAINERS: Add entry for genwqe driver
VMCI: Doorbell create and destroy fixes
GenWQE: Fix bad page access during abort of resource allocation
vme: vme_get_size potentially returning incorrect value on failure
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYFQwAAAoJEHm+PkMAQRiGr8YH/0urDFZm/RFu752rSawF7iVM
nx9Ck03YkRiMRZfdzPARbHJts7lhLG1rvsT50VQNMK1sVv0BXcrnJnDu49xV+dLj
DqXWvYGtdTCpAd34Am37pX/rrRl11vdJgS2VgprmbytkM8FD0xEe+aDKxnnmuALo
bggYDhMrJik3/UXG0zVfefKZJFLNAJiZv9AgWgkCR+bo861bu3UFn47tN1jGXOOl
QyFl5t7ggesojA5Q1U9hTrk1gS9Ia9it3Elyzfqb66lUdyf001I1nbUA/hNYyDXD
HU9dj3agvVXjvnDjyDR4/k86FA+EEEwSgk5CBTCVe30dLKnojFyb7FWZg72utg4=
=CHER
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rc3' into next/dt
Linux 4.9-rc3
* tag 'v4.9-rc3': (292 commits)
Linux 4.9-rc3
x86/smpboot: Init apic mapping before usage
ACPICA: Dispatcher: Fix interpreter locking around acpi_ev_initialize_region()
ACPICA: Dispatcher: Fix an unbalanced lock exit path in acpi_ds_auto_serialize_method()
ACPICA: Dispatcher: Fix order issue of method termination
ARC: module: print pretty section names
ARC: module: elide loop to save reference to .eh_frame
ARC: mm: retire ARC_DBG_TLB_MISS_COUNT...
ARC: build: retire old toggles
ARC: boot log: refactor cpu name/release printing
ARC: boot log: remove awkward space comma from MMU line
ARC: boot log: don't assume SWAPE instruction support
ARC: boot log: refactor printing abt features not captured in BCRs
ARCv2: boot log: print IOC exists as well as enabled status
ubifs: Fix regression in ubifs_readdir()
ubi: fastmap: Fix add_vol() return value test in ubi_attach_fastmap()
MAINTAINERS: Add entry for genwqe driver
VMCI: Doorbell create and destroy fixes
GenWQE: Fix bad page access during abort of resource allocation
vme: vme_get_size potentially returning incorrect value on failure
...
Enhancements:
* Basic support for r8a7743 SoC; only SoC code so far
* Select errata 798181 for SoCs with CA15 cores
Clean-up:
* Consolidate R8A7743 and R8A779[234] machine definitions
Documentation:
* Add Marzen, Gose and Alt board part numbers to DT bindings
* Document SK-RZG1M board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CqVV
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Renesas ARM Based SoC Updates for v4.10
Enhancements:
* Basic support for r8a7743 SoC; only SoC code so far
* Select errata 798181 for SoCs with CA15 cores
Clean-up:
* Consolidate R8A7743 and R8A779[234] machine definitions
Documentation:
* Add Marzen, Gose and Alt board part numbers to DT bindings
* Document SK-RZG1M board
* tag 'renesas-soc-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7779/marzen: Add board part number to DT bindings
ARM: shmobile: select errata 798181 for SoCs with CA15 cores
ARM: shmobile: Consolidate R8A7743 and R8A779[234] machine definitions
ARM: shmobile: r8a7793/gose: Add board part number to DT bindings
ARM: shmobile: r8a7794/alt: Add board part number to DT bindings
ARM: shmobile: document SK-RZG1M board
ARM: shmobile: r8a7743: basic SoC support
ARM: shmobile: only call rcar_gen2_clocks_init() if present
ARM: shmobile: Sort Kconfig selections
Signed-off-by: Olof Johansson <olof@lixom.net>
features printed, all these are quite trivial and tiny. The omap5 jack
detection and gpadc patches are not strictly fixes, but I wanted to get
binding document typo fixed before it pops up on other boards. The
gpadc one liner was in the same series and I applied and pushed it out
already before noticing it could have waited. The list of changes is:
- Fix omap3 SoC features printed
- Make sure OMAP_INTERCONNECT is selected for am43xx only configurations
- Add missing memory node for torpedo
- Initialize uart4_mask properly to avoid writing garbage to PRM registers
- Fix NULL pointer dereference for omap4 volt_data
- Add alias for omap5 gpadc needed by iio drivers
- Enable omap5 jack headset jack detection and fix it's binding typo
- Add missing memory node for logicpd-som-lv
- Fix wrong SMPS6 voltage for VDD-DDR3 for omap5
-----BEGIN PGP SIGNATURE-----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=LgIW
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.9/fixes-for-rc-cycle' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.9-rc cycle. Except for the omap3 fix for the SoC
features printed, all these are quite trivial and tiny. The omap5 jack
detection and gpadc patches are not strictly fixes, but I wanted to get
binding document typo fixed before it pops up on other boards. The
gpadc one liner was in the same series and I applied and pushed it out
already before noticing it could have waited. The list of changes is:
- Fix omap3 SoC features printed
- Make sure OMAP_INTERCONNECT is selected for am43xx only configurations
- Add missing memory node for torpedo
- Initialize uart4_mask properly to avoid writing garbage to PRM registers
- Fix NULL pointer dereference for omap4 volt_data
- Add alias for omap5 gpadc needed by iio drivers
- Enable omap5 jack headset jack detection and fix it's binding typo
- Add missing memory node for logicpd-som-lv
- Fix wrong SMPS6 voltage for VDD-DDR3 for omap5
* tag 'omap-for-v4.9/fixes-for-rc-cycle' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: board-common: fix wrong SMPS6 (VDD-DDR3) voltage
ARM: omap3: Add missing memory node in SOM-LV
ASoC: omap-abe-twl6040: fix typo in bindings documentation
dts: omap5: board-common: enable twl6040 headset jack detection
dts: omap5: board-common: add phandle to reference Palmas gpadc
ARM: OMAP2+: avoid NULL pointer dereference
ARM: OMAP2+: PRM: initialize en_uart4_mask and grpsel_uart4_mask
ARM: dts: omap3: Fix memory node in Torpedo board
ARM: AM43XX: Select OMAP_INTERCONNECT in Kconfig
ARM: OMAP3: Fix formatting of features printed
Signed-off-by: Olof Johansson <olof@lixom.net>
The Aspeed SoCs have two BT interfaces : one is IPMI compliant and the
other is H8S/2168 compliant.
The current ipmi/bt-bmc driver implements the IPMI version and we
should reflect its nature in the compatible node name using
'aspeed,ast2400-ibt-bmc' instead of 'aspeed,ast2400-bt-bmc'. The
latter should be used for a H8S interface driver if it is implemented
one day.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove the following outbound related device tree properties:
brcm,pcie-ob-window-size
brcm,pcie-ob-oarr-size
The above two properties are a bit duplicated in functions. In addition,
the next generation iProc PCIe controller has outbound mapping window that
supports more than just two sizes, which cannot be properly supported by
these properties.
[bhelgaas: changelog]
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
(decoupled from the generic scpi binding)
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
This patch adds specific compatible to support all the unversioned SCPI
protocols prior to v1.0 release. This will be applicable for all the
implementations using draft versions or modified versions of those
draft vesrions of SCPI protocol.
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Since SCPI is a generic protocol and the bindings are intended to be
generic, we need to decouple all the platform specific binding details
out of the generic bindings.
This patch moves are the Juno platform specific details into a separate
binding document.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Audio block requires access to two parent clocks: audio PLL and oscillator,
so add this information to device tree bindings documentation.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The proper parent clock for FSYS block is "aclk_fsys_200"
according to the Exynos5433 reference manual.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Some dumb VGA DACs are active components which require external power.
Add support for specifying a regulator as its power supply.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161116154232.872-2-wens@csie.org
On some tablets the touchscreen controller is powered by separate
regulators, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The usual patches from us, but most notably the introduction of the A64
clocks unit.
-----BEGIN PGP SIGNATURE-----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=7+Az
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Pull Allwinner clock changes from Maxime Ripard:
The usual patches from us, but most notably the introduction of the A64
clocks unit.
* tag 'sunxi-clk-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
clk: sunxi-ng: sun8i-h3: Set CLK_SET_RATE_PARENT for audio module clocks
clk: sunxi-ng: sun8i-a23: Set CLK_SET_RATE_PARENT for audio module clocks
clk: sunxi-ng: Add A64 clocks
clk: sunxi-ng: Implement minimum for multipliers
clk: sunxi-ng: Add minimums for all the relevant structures and clocks
clk: sunxi-ng: Finish to convert to structures for arguments
clk: sunxi-ng: Remove the use of rational computations
clk: sunxi-ng: Rename the internal structures
clk: sunxi: mod0: improve function-level documentation
This patch adds support for Exynos5433 specific version of the GScaler
module. The main difference between Exynos 5433 and earlier is addition
of new clocks that have to be controlled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The FDP1 is a de-interlacing module which converts interlaced video to
progressive video. It is also capable of performing pixel format conversion
between YCbCr/YUV formats and RGB formats.
Signed-off-by: Kieran Bingham <kieran+renesas@bingham.xyz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Includes Peter Rosin's interesting drivers for a comparator. First complex
use we have had with an analog front end made from discrete components.
Brian Masney's work on moving the tsl2583 driver out of staging also
feature extensively!
New Drivers
* DAC based on a digital potentiometer
- New driver for the use of a dpot as a DAC. Includes bindings and Axentia
entry in vendor prefixes.
* Envelope detector baed on DAC and a comparator including device tree
bindings.
Staging Graduation
* tsl2583.
Core new features
- Core provision for _available attributes. This one had been stalled for
a long time until Peter picked it up and ran with it!
- In kernel interface helpers to retrieve available info from channels.
Driver new features
* mcp4531
- Add range of available raw values (used for the dpot dac driver).
Driver cleanups and fixes for issues introduced
* ad7766
- Testing the wrong variable following devm_regulator_bulk_get introduced
with the driver earlier in this cycle.
* ad9832
- Fix a wrong ordering in the probe introduced in the previous set of
patches. A use before allocation bug.
* cros_ec_sensors
- Testing for an error in a u8 will never work.
* mpu3050
- Remove duplicate initializer for the module owner.
- Add missing i2c dependency.
- Inform the i2c mux core how it is used - step one in implifying device
tree bindings.
* st-sensors
- Get rid of large number of uninformative defines in favour of putting the
constants where they are relevant. It is clear what they are from where
they are used.
* tsl2583
- Fix unused function warning when CONFIG_PM disabled and remove the
ifdefs in favour of __maybe_unused.
- Refactor taos_chip_on to only read relevant registers.
- Make sure calibscale and integration time are being set.
- Verify chip is in ready to be used before calibration.
- Remove some repeated checks for chip status (it's protected by a mutex
so can't change until it's released)
- Change current state storage from a tristate enum to a boolean seeing as
only two values are actually used now.
- Drop a redundant write to the control regiser in taos_probe (it's a noop)
- Drop the FSF mailing address.
- Clean up logging to not use hard coded function names (use __func__
instead).
- Cleanup up variable and function name prefixes.
- Alignment of #define fixes.
- Fix comparison between signed and unsigned integer warnings.
- Add some newlines in favour of readability.
- Combine the two sysfs ABI docs that somehow ended up in different places.
- Fix multiline comment syntax.
- Move a code block to inside an else statement as it makes more sense there.
- Change tsl2583_als_calibrate to return 0 rather than a value nothing
reads.
- Drop some pointless brackets
- Don't assume 32bit unsigned int.
- Change to a per device instance lux table.
- Add missing tsl2583 to the list of supported devices in the intro comments.
- Improve commment on clearing of interrupts.
- Drop some uninformative comments.
- Drop a memset call that doesn't do anything useful any more.
- Don't initialize some return variables that are always set.
- Add Brian Masney as a module author after all these changes.
-----BEGIN PGP SIGNATURE-----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=mPkb
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.10c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third set of IIO new device support, features and cleanup for the 4.10 cycle.
Includes Peter Rosin's interesting drivers for a comparator. First complex
use we have had with an analog front end made from discrete components.
Brian Masney's work on moving the tsl2583 driver out of staging also
feature extensively!
New Drivers
* DAC based on a digital potentiometer
- New driver for the use of a dpot as a DAC. Includes bindings and Axentia
entry in vendor prefixes.
* Envelope detector baed on DAC and a comparator including device tree
bindings.
Staging Graduation
* tsl2583.
Core new features
- Core provision for _available attributes. This one had been stalled for
a long time until Peter picked it up and ran with it!
- In kernel interface helpers to retrieve available info from channels.
Driver new features
* mcp4531
- Add range of available raw values (used for the dpot dac driver).
Driver cleanups and fixes for issues introduced
* ad7766
- Testing the wrong variable following devm_regulator_bulk_get introduced
with the driver earlier in this cycle.
* ad9832
- Fix a wrong ordering in the probe introduced in the previous set of
patches. A use before allocation bug.
* cros_ec_sensors
- Testing for an error in a u8 will never work.
* mpu3050
- Remove duplicate initializer for the module owner.
- Add missing i2c dependency.
- Inform the i2c mux core how it is used - step one in implifying device
tree bindings.
* st-sensors
- Get rid of large number of uninformative defines in favour of putting the
constants where they are relevant. It is clear what they are from where
they are used.
* tsl2583
- Fix unused function warning when CONFIG_PM disabled and remove the
ifdefs in favour of __maybe_unused.
- Refactor taos_chip_on to only read relevant registers.
- Make sure calibscale and integration time are being set.
- Verify chip is in ready to be used before calibration.
- Remove some repeated checks for chip status (it's protected by a mutex
so can't change until it's released)
- Change current state storage from a tristate enum to a boolean seeing as
only two values are actually used now.
- Drop a redundant write to the control regiser in taos_probe (it's a noop)
- Drop the FSF mailing address.
- Clean up logging to not use hard coded function names (use __func__
instead).
- Cleanup up variable and function name prefixes.
- Alignment of #define fixes.
- Fix comparison between signed and unsigned integer warnings.
- Add some newlines in favour of readability.
- Combine the two sysfs ABI docs that somehow ended up in different places.
- Fix multiline comment syntax.
- Move a code block to inside an else statement as it makes more sense there.
- Change tsl2583_als_calibrate to return 0 rather than a value nothing
reads.
- Drop some pointless brackets
- Don't assume 32bit unsigned int.
- Change to a per device instance lux table.
- Add missing tsl2583 to the list of supported devices in the intro comments.
- Improve commment on clearing of interrupts.
- Drop some uninformative comments.
- Drop a memset call that doesn't do anything useful any more.
- Don't initialize some return variables that are always set.
- Add Brian Masney as a module author after all these changes.
This adds the dt-binding documentation for the clock and reset unit
found on Rockchip rk1108 SoCs.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The TSE-850 is an FM Transmitter Station Equipment, designed to generate
baseband signals for FM, mainly the DARC subcarrier, but other signals
are also possible.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
This document defines the binding for a component that loads firmware
and control the life cycle of the Qualcomm ADSP Hexagon core.
Acked-by: Rob Herring <robh@kernel.org>
Cc: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If the RAMOOPS_FLAG_FTRACE_PER_CPU flag is passed to ramoops pdata, split
the ftrace space into multiple zones depending on the number of CPUs.
This speeds up the performance of function tracing by about 280% in my
tests as we avoid the locking. The trade off being lesser space available
per CPU. Let the ramoops user decide which option they want based on pdata
flag.
Signed-off-by: Joel Fernandes <joelaf@google.com>
[kees: added max_ftrace_cnt to track size, added DT logic and docs]
Signed-off-by: Kees Cook <keescook@chromium.org>
Support for the Allwinner A31 SoC display engine using the sun4i-drm
driver.
-----BEGIN PGP SIGNATURE-----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=fERq
-----END PGP SIGNATURE-----
Merge tag 'sunxi-drm-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into drm-next
sun4i-drm changes for 4.10
Support for the Allwinner A31 SoC display engine using the sun4i-drm
driver.
* tag 'sunxi-drm-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
drm/sun4i: Add a few formats
drm/sun4i: Add compatible strings for A31/A31s display pipelines
drm/sun4i: Add compatible string for A31/A31s TCON (timing controller)
drm/sun4i: tcon: Move SoC specific quirks to a DT matched data structure
drm/sun4i: sun6i-drc: Support DRC on A31 and A31s
Document the devicetree bindings for the Generic Memory Interface (GMI)
bus driver found on Tegra SOCs.
Signed-off-by: Mirza Krak <mirza.krak@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Colibri T20/T30 on EvalBoard V3.x and GMI-Memory Board
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Udoo (http://www.udoo.org/) manufactures development boards based on
i.MX and x86.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a vendor prefix for Samtec, a Softing company.
http://www.samtec.dehttp://www.samtec.org
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a vendor prefix for the Macnica company.
http://http://www.macnica.com
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Add vendor prefix for Aries Embedded GmbH
http://www.aries-embedded.de/
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
As of commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated"), including skeleton.dtsi is deprecated.
Hence remove it from the example.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add documentation how devicetree can be used to configure ath9k based
devices.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add DT binding for the Hardware Synchronization Primitives (HSP). The
HSP is designed for the processors to share resources and communicate
with one another. A set of hardware synchronization primitives for
interprocessor communication (IPC) is provided. IPC protocols can use
use these hardware synchronization primitives when operating between
processors in an AMP configuration.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds documentation for the devicetree bindings used by
the DT files of Hisilicon Hip07 D05 board.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Document the SK-RZG1E device tree bindings, listing it as a supported board.
This allows to use checkpatch.pl to validate .dts files referring to the
SK-RZG1E board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds the dt-binding documentation for rk1108 pinctrl
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add minimal support for the RZ/G1E (R8A7745) SoC.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The pin controller found in the Allwinner SoCs has support for interrupts
debouncing.
However, this is not done per-pin, preventing us from using the generic
pinconf binding for that, but per irq bank, which, depending on the SoC,
ranges from one to five.
Introduce a device-wide property to deal with this using a microsecond
resolution. We can re-use the per-pin input-debounce property for that, so
let's do it!
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch add the support of GPF[1-5] pin of Exynos5433 SoC. The GPFx need
to support the multiple memory map because the registers of GPFx are located
in the different domain.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow the associated smd edge to be described within the wcnss
remoteproc node. This creates a bond between the remoteproc and the
associated smd channels and devices, showing the interaction between the
two parts and provides both a natural reference to the other.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Document the R8A7796-specific DT bindings and support them in the
driver. The HDMI output is currently not supported.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add support for the R8A7792 DU; it has 2 DPAD (RGB) outputs.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add "rockchip,rk1108-dw-mshc", "rockchip,rk3288-dw-mshc" for
dwmmc on rk1108 platform.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add new compatible string "brcm,iproc-pcie-paxc-v2" to the iProc PCIe
device tree binding document. "brcm,iproc-pcie-paxc-v2" is for the second
generation of the Broadcom iProc PCIe PAXC host controller.
Update the binding document with more detailed description of each
compatible string and compatible SoCs.
Add description of optional property "msi-map", for use with MSI
controllers with sideband data.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Some of the host drivers have the requirement of knowing whether the EP
would never train at some link speed at all. For instance, on some boards,
the link won't train at 5 GT/s but the host driver still sacrifice some
cycles to wait for the result of training at 5 GT/s as the host could
actually support 5 GT/s. So we could parse this new property and make the
host drivers be aware of these cases.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Create the driver for the da8xx master peripheral priority
configuration and implement support for writing to the three
Master Priority registers on da850 SoCs.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: subject line adjustment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Create a new driver for the da8xx DDR2/mDDR controller and implement
support for writing to the Peripheral Bus Burst Priority Register.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: subject line adjustment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch adds support for Renesas r8a7796 SoC. This SoC is not
compatible with r8a7795 because using firmware version differs.
Since the "V2" firmware can be used on both r8a7795 (es1.x) and r8a7796,
the "renesas,rcar-gen3-xhci" keeps to use the "V2" for now.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to a hardware bug, reading memory (from the Accelerator Coherency Port)
with a burst size equal to the maximum burst size allowed by the DMA
hardware's buffer size will cause a hardware hang on the ARTPEC-6 SoC,
where the only solution is a manual power cycle.
On ARTPEC-6, this hardware bug does not trigger when writing memory (to the
Accelerator Coherency Port) with a burst size equal to the maximum burst
size allowed by the DMA hardware's buffer size.
To avoid this hardware hang, introduce a new optional max-burst property
for memory reads. For completeness, also introduce a max-burst property for
memory writes.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The DAC3101 is mostly identical to DAC3100 with the exception that it has
stereo speaker AMP instead of mono used in DAC3100.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5c2j
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.9-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Update MAINTAINERS for Intel VMD driver filename
- Update Rockchip rk3399 host bridge driver DTS and resets
- Fix ROM shadow problem that made some video device initialization
fail
* tag 'pci-v4.9-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: VMD: Update filename to reflect move
arm64: dts: rockchip: add three new resets for rk3399 PCIe controller
PCI: rockchip: Add three new resets as required properties
PCI: Don't attempt to claim shadow copies of ROM
- Fix mmc card initialization for hosts not supporting HW busy detection
- Fix mmc_test for sending commands during non-blocking write
MMC host:
- mxs: Avoid using an uninitialized
- sdhci: Restore enhanced strobe setting during runtime resume
- sdhci: Fix a couple of reset related issues
- dw_mmc: Fix a reset controller issue
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mnjf
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix mmc card initialization for hosts not supporting HW busy
detection
- Fix mmc_test for sending commands during non-blocking write
MMC host:
- mxs: Avoid using an uninitialized
- sdhci: Restore enhanced strobe setting during runtime resume
- sdhci: Fix a couple of reset related issues
- dw_mmc: Fix a reset controller issue"
* tag 'mmc-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: mxs: Initialize the spinlock prior to using it
mmc: mmc: Use 500ms as the default generic CMD6 timeout
mmc: mmc_test: Fix "Commands during non-blocking write" tests
mmc: sdhci: Fix missing enhanced strobe setting during runtime resume
mmc: sdhci: Reset cmd and data circuits after tuning failure
mmc: sdhci: Fix unexpected data interrupt handling
mmc: sdhci: Fix CMD line reset interfering with ongoing data transfer
mmc: dw_mmc: add the "reset" as name of reset controller
Documentation: synopsys-dw-mshc: add binding for reset-names
- Fix a host of runtime problems with the Intel
Cherryview driver: suspend/resume needs to be
marshalled properly, and strange effects from BIOS
interaction during suspend/resume need to be
dealt with.
- A single bit was being set wrong in the Aspeed
driver.
- Fix an iProc probe ordering fallout resulting from
v4.9 refactorings for bus population.
- Do not specify a default trigger in the ST Micro
cascaded GPIO IRQ controller: the kernel will moan.
- Make IRQs optional altogether on the STM32 driver,
it turns out not all systems have them or want them.
- Fix a re-probe bug in the i.MX driver, it will
eventually crash if probed repeatedly, not good.
-----BEGIN PGP SIGNATURE-----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=ENR8
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"All is about drivers, no core business going on.
- Fix a host of runtime problems with the Intel Cherryview driver:
suspend/resume needs to be marshalled properly, and strange effects
from BIOS interaction during suspend/resume need to be dealt with.
- A single bit was being set wrong in the Aspeed driver.
- Fix an iProc probe ordering fallout resulting from v4.9
refactorings for bus population.
- Do not specify a default trigger in the ST Micro cascaded GPIO IRQ
controller: the kernel will moan.
- Make IRQs optional altogether on the STM32 driver, it turns out not
all systems have them or want them.
- Fix a re-probe bug in the i.MX driver, it will eventually crash if
probed repeatedly, not good"
* tag 'pinctrl-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl-aspeed-g5: Never set SCU90[6]
pinctrl: cherryview: Prevent possible interrupt storm on resume
pinctrl: cherryview: Serialize register access in suspend/resume
pinctrl: imx: reset group index on probe
pinctrl: stm32: move gpio irqs binding to optional
pinctrl: stm32: remove dependency with interrupt controller
pinctrl: st: don't specify default interrupt trigger
pinctrl: iproc: Fix iProc and NSP GPIO support
Add CRG driver for Hi3798CV200 SoC. CRG(Clock and Reset
Generator) module generates clock and reset signals used
by other module blocks on SoC.
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the LS1046a PCIe controller. This device has a different
LUT_DBG offset, so add "lut_dbg" to ls_pcie_drvdata to
describe this difference.
[bhelgaas: changelog, remove now-unused PCIE_LUT_DBG]
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In order to have a proper topology of regulators for a platform, each
registering regulator needs to populate supply_name field for identifying
its supply's name. Add supply_name field for lp873x regulators.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds initial support for clocks controlled by the Resource
Power Manager (RPM) processor on some Qualcomm SoCs, which use
the qcom_rpm driver to communicate with RPM.
Such platforms are apq8064 and msm8960.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This adds initial support for clocks controlled by the Resource
Power Manager (RPM) processor on some Qualcomm SoCs, which use
the qcom_smd_rpm driver to communicate with RPM.
Such platforms are msm8916, apq8084 and msm8974.
The RPM is a dedicated hardware engine for managing the shared
SoC resources in order to keep the lowest power profile. It
communicates with other hardware subsystems via shared memory
and accepts clock requests, aggregates the requests and turns
the clocks on/off or scales them on demand.
This driver is based on the codeaurora.org driver:
https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.10/tree/drivers/clk/qcom/clock-rpm.c
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
[sboyd@codeaurora.org: Remove useless braces for single line if]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This is the initial ZTE VOU display controller DRM/KMS driver. There
are still some features to be added, like overlay plane, scaling, and
more output devices support. But it's already useful with dual CRTCs
and HDMI display working.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYH++oAAoJEFBXWFqHsHzOlCQIAKLNtBmB2OSChdPRCa7tIG7O
vtjUwze70QtD6vVe+rs0fvc46PM3qrccJI6bcgzveki+vRvFVDlreydmB18g3bMx
cBbsByGnWrNWDtKrwvvRWrkDQwcxnSVX5lMWeIvLrPHeXQVb4nf0F2cn7/zEfIek
G55LHonRD28m66tWb87gaWwisowcaPzA3tAEP4Rifdqg9IQ45He7Po6KZWZU4DQq
M/RltIHQwt/OFxAnDuz18ecf+o0NXuLoMYmoA8EYdOTV3sJ2hiJQFWaL5qmXKl7C
Nzlql70txu9B9H5R4V/6MXS21J0H2uGs2Aig9l9Brz2Vn774IBX09Wi8Fo8G8VU=
=+zjh
-----END PGP SIGNATURE-----
Merge tag 'zxdrm-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into drm-next
ZTE zxdrm driver support for 4.10:
This is the initial ZTE VOU display controller DRM/KMS driver. There
are still some features to be added, like overlay plane, scaling, and
more output devices support. But it's already useful with dual CRTCs
and HDMI display working.
[airlied: use drm_format_plane_cpp instead of legacy api]
* tag 'zxdrm-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
MAINTAINERS: add an entry for ZTE ZX DRM driver
drm: zte: add initial vou drm driver
dt-bindings: add bindings doc for ZTE VOU display controller
- add support for the HDMI I2C master controller, for boards that
can have their DDC pins connected only to the HDMI TX directly.
-----BEGIN PGP SIGNATURE-----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=aAzo
-----END PGP SIGNATURE-----
Merge tag 'dw-hdmi-next-2016-09-19' of git://git.pengutronix.de/git/pza/linux into drm-next
dw-hdmi i2c master controller
- add support for the HDMI I2C master controller, for boards that
can have their DDC pins connected only to the HDMI TX directly.
* tag 'dw-hdmi-next-2016-09-19' of git://git.pengutronix.de/git/pza/linux:
drm: bridge/dw_hdmi: add dw hdmi i2c bus adapter support
drm: dw_hdmi: use of_get_i2c_adapter_by_node interface
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
[sboyd@codeaurora.org: Dropped unused and incorrect GDSC defines]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
pm_rst, aclk_rst, pclk_rst was controlled by ROM code so the software
wasn't needed to control it again in theory. But it didn't work properly,
so we do need to do it again and add enough delay between the assert of
pm_rst and the deassert of pm_rst. The Soc intergrated with this
controller, rk3399, is still under MP test internally, so the backward
compatibility won't be a big deal.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Since there is not enough tcam table entries for every vlan and multicast
address, HNS needs to add support of fuzzy matching of TCAM tables. Adding
the property to mask the bits to be fuzzy matched, so update the bindings
document
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New bindings document for FPGA Region to support programming
FPGA's under Device Tree control
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added a driver for the Holtek HT16K33 LED controller with keyscan.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
CC: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add RZ/G1E (R8A7745) Clock Pulse Generator / Module Standby and Software
Reset support, using the CPG/MSSR driver core and the common R-Car Gen2
(and RZ/G) code.
Based on the proof-of-concept R8A7791 CPG/MSSR patch by Geert
Uytterhoeven <geert+renesas@glider.be>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add RZ/G1M (R8A7743) Clock Pulse Generator / Module Standby and Software
Reset support, using the CPG/MSSR driver core and the common R-Car Gen2
(and RZ/G) code.
Based on the proof-of-concept R8A7791 CPG/MSSR patch by Geert
Uytterhoeven <geert+renesas@glider.be>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
DRA71x processor family is a derivative of DRA722 ES2.0 targetted for
infotainment systems.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to support PHY switching on Amlogic GXL SoCs, add support for
16bit and 32bit registers sizes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devicetree bindings documentation file for Cirrus
Logic CS42L42 codec.
Signed-off-by: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add binding information for DA9061 onkey.
This patch updates the compatible string "dlg,da9061-onkey" to support
DA9061, removes the reference to KEY_SLEEP (which the driver no longer
supports) and fixes a typo in the example for DA9063.
Supporting KEY_SLEEP was not the general convention and the typical
solution should have been for KEY_POWER to support both cases of suspend
and S/W power off. This change was sent to the DA9063 ONKEY device
driver in a separate patch, but the documentation was not updated at
that time.
- f889bea Report KEY_POWER instead of KEY_SLEEP during power key-press
This patch also adds two new examples, one for DA9062 and one for DA9061.
The DA9061 examples uses a fall-back compatible string for the DA9062
onkey driver.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add a new compatible string for 14nm ufs phy present on msm8996
chipset. This phy is bit different from the legacy 14nm ufs phy
in terms of the clocks that are needed to be handled in the driver.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for hip07 chipset to hisi_sas controller.
Chipset hip07 has v2 hw.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* Add support for the r8a7743 SoC to rcar-sysc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XcYr
-----END PGP SIGNATURE-----
Merge tag 'renesas-drivers-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
Renesas ARM Based SoC Drivers Updates for v4.10
* Add support for the r8a7743 SoC to rcar-sysc
* tag 'renesas-drivers-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
soc: renesas: rcar-sysc: add R8A7743 support
ARM: shmobile: r8a7743: add power domain index macros
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Peter Ujfalusi <perter.ujfalusi@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add atmel,sama5d2-securam to the compatible list.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
A security module is available starting with sama5d2, add its bindings.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
ARM systems may be configured to have cpus with different power/performance
characteristics within the same chip. In this case, additional information
has to be made available to the kernel (the scheduler in particular) for it
to be aware of such differences and take decisions accordingly.
Therefore, this patch aims at standardizing cpu capacities device tree
bindings for ARM platforms. Bindings define cpu capacity-dmips-mhz
parameter, to allow operating systems to retrieve such information from
the device tree and initialize related kernel structures, paving the way
for common code in the kernel to deal with heterogeneity.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Clean-up the documentation to the bgmac-amac driver, per suggestion by
Rob Herring, and add details for NS2 support.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the documentation for PHY lane swapping. This is a boolean entry to
notify the phy device drivers that the TX/RX lanes need to be swapped.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers using pinctrl-single,pins have #pinctrl-cells = <1>, while
pinctrl-single,bits need #pinctrl-cells = <2>.
Note that this patch can be optionally applied separately from the
driver changes as the driver supports also the legacy binding without
#pinctrl-cells.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adds the device tree bindings description for Samsung S3C2410 and
compatible NAND flash controller.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The description for dmas references a second property, which should be
"dma-names" instead of "clock-names".
Signed-off-by: Mirza Krak <mirza.krak@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This includes two branch merges for elements that may also go via MFD.
New device support
* cros_ec
- new driver to support these Chrome OS contiguous sensors which are behind
the Chrome OS embedded controller. Requires a few minor MFD and chrome
platform changes. One follow up fix deals with some dependency issues in
Kconfig.
* mpu-3050
- new driver and device tree bindings for this venerable device.
* st_accel
- support for the lng2dm an
Driver features
* ad7192
- Add DVdd regulator handling
* ad9832
- Add DVDD regulator handling
* at91
- Suspend and resume support
* si7020
- Device tree bindings
* ti-am335x
- DMA support - uses dma to accelerate short bursts of read back rather
than full blown DMA buffer support. Greatly improved performance.
Includes an MFD addition to give access to the address needed for DMA.
* tsl2583
- Device tree bindings
Cleanups and minor fixes
* ad7192
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg variable to reflect which regulator it is
* ad5933
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad7746
- Fix a missing return value (fallout from previous patch set)
* ad7780
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad9832
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg regulator to reflect which one it is
* ad9834
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* hts221
- Remove a duplicated include
* maxim thermocouple
- Handle a wrong storage side in read function. Prevent any problems that
might be introduced by additions to this driver in future.
* tsl2583 - big set from Brian Masney to drive this towards a staging
graduation.
- Convert to iio_chan_spec and read_raw / write_raw (in a couple of steps)
- Improved error handling in various functions
- Drop redundant power_state custom sysfs attribute.
- Use IIO_*_ATTR* macros for remaining attributes.
- Return an error code to userspace on invalid parameters being writen to
sysfs files.
- Add locking to various attribute accesses to remove possible races.
- Add defines for various magic numbers.
- Use smbus_read_byte_data instead of a write_byte followed by read_byte.
- Query only relevant registers in probe.
- Tidy up ordering of code comments.
- Remove a pointless power off sequence in taos_chip_on.
- Don't bother shutting down the chip when updating the lux table.
The table is held entirely in the driver and doesn't effect the chip at all.
- Drop a redundant i2c call in taos_als_calibrate where the same register
is read twice in a row.
-----BEGIN PGP SIGNATURE-----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=ptGw
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.10b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
Second round of new device support, cleanups and fixes for IIO in the 4.10 cycle
This includes two branch merges for elements that may also go via MFD.
New device support
* cros_ec
- new driver to support these Chrome OS contiguous sensors which are behind
the Chrome OS embedded controller. Requires a few minor MFD and chrome
platform changes. One follow up fix deals with some dependency issues in
Kconfig.
* mpu-3050
- new driver and device tree bindings for this venerable device.
* st_accel
- support for the lng2dm an
Driver features
* ad7192
- Add DVdd regulator handling
* ad9832
- Add DVDD regulator handling
* at91
- Suspend and resume support
* si7020
- Device tree bindings
* ti-am335x
- DMA support - uses dma to accelerate short bursts of read back rather
than full blown DMA buffer support. Greatly improved performance.
Includes an MFD addition to give access to the address needed for DMA.
* tsl2583
- Device tree bindings
Cleanups and minor fixes
* ad7192
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg variable to reflect which regulator it is
* ad5933
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad7746
- Fix a missing return value (fallout from previous patch set)
* ad7780
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad9832
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg regulator to reflect which one it is
* ad9834
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* hts221
- Remove a duplicated include
* maxim thermocouple
- Handle a wrong storage side in read function. Prevent any problems that
might be introduced by additions to this driver in future.
* tsl2583 - big set from Brian Masney to drive this towards a staging
graduation.
- Convert to iio_chan_spec and read_raw / write_raw (in a couple of steps)
- Improved error handling in various functions
- Drop redundant power_state custom sysfs attribute.
- Use IIO_*_ATTR* macros for remaining attributes.
- Return an error code to userspace on invalid parameters being writen to
sysfs files.
- Add locking to various attribute accesses to remove possible races.
- Add defines for various magic numbers.
- Use smbus_read_byte_data instead of a write_byte followed by read_byte.
- Query only relevant registers in probe.
- Tidy up ordering of code comments.
- Remove a pointless power off sequence in taos_chip_on.
- Don't bother shutting down the chip when updating the lux table.
The table is held entirely in the driver and doesn't effect the chip at all.
- Drop a redundant i2c call in taos_als_calibrate where the same register
is read twice in a row.
Add reset-names property for binding dw-mmc controller.
It might be used together with "reset" property.
- Note: It must be "reset" as name.
Fixes: d6786fefe8 ("mmc: dw_mmc: add reset support to dwmmc host controller")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It adds initial bindings doc for ZTE VOU display controller. HDMI is
the only supported output device right now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYHmoCAAoJEHm+PkMAQRiG7RMIAI2i7Y5hpL5yCxK5AFaL4u/G
KxXfp1B1UanUTgjOmd7zGqtDYcFX9t7GTTUFixQ7/9Opr4PD9qbnatoDGSc3xjbT
msDgA1B78F1/Q3kHWfeGq32MihQ4mj5NwUCo+igUcUvvWG7mHgzErj/Nh5RoobQX
p/izdpTbrw3GX6xXB8olbG7XWHaVye/+TT3q6+gmgm8I/QEujcLeGoycE0zlhPN8
FG/JX76At/+ZM2Py7Oxo3k+oKL9CHrtOQYDp/wN0uslV5eYvvkZz0/M1HMOGZt+c
gZU5jzM17K7C4Nzo06WAuBU9wUBGc25m+cPicLlOmljnzfU+f50SKaDjZq3p7QI=
=2KUF
-----END PGP SIGNATURE-----
Backmerge tag 'v4.9-rc4' into drm-next
Linux 4.9-rc4
This is needed for nouveau development.
Add interrupts documentation
Fix example and formatting
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Initial pinctrl driver for QCOM msm8994 platforms.
In order to continue the initial board support for QCOM msm8994/msm8992
presented in patches from Jeremy McNicoll <jeremymc@redhat.com>, let's put
a proper pinctrl driver in place.
Currently, the DT for these platforms uses the msm8x74 pinctrl driver to
enable basic UART. Beyond the first few pins the rest are different enough
to justify it's own driver.
Note: This driver is also used by QCOM's msm8992 platform as it's TLM block
is the same.
- Initial formatting and style was taken from the msm8x74 pinctrl driver
added by Björn Andersson <bjorn.andersson@linaro.org>
- Data was then adjusted per QCOM MSM8994v2 documentation for Top Level
Multiplexing
- Bindings documentation was based on qcom,msm8996-pinctrl.txt by
Joonwoo Park <joonwoop@codeaurora.org> and then modified for msm8994
content
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds documentation for the device-tree bindings of the
jz4740-rtc driver, which supports the RTC unit present in the JZ4740 and
JZ4780 SoCs from Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add support for the Amlogic Meson GXL SoC, this is a partially complete
definition only based on the Amlogic Vendor tree.
This definition differs a lot from the GXBB and needs a separate entry.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A31 SoC's codec has various inputs, outputs and microphone bias
supplies. These can be routed on the board in different ways, such as:
- HPCOM may be connected to have the headphone DC coupled.
- Microphones all use the MBIAS main microphone supply or one mic may
use the HBIAS supply, which supports headset detection and buttons.
- Line Out may be routed to an audio jack, or an onboard speaker amp
with power controls.
Add support for specifying the audio routes in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add device tree for the Oxford Seminconductor OX820 SoC and the
Cloud Engines PogoPlug v3 board.
Add the SoC and board compatible strings to oxnas bindings.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The A31 has a similar codec to the A10/A20. The PCM parts are very
similar, with different register offsets. The analog paths are very
different. There are more inputs and outputs. The ADC mux has been
replaced with a proper mixer.
This patch adds support for the basic playback path of the A31 codec,
from the DAC to the headphones. Headphone detection, microphone,
signaling, other inputs/outputs and capture will be added later.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the Device Tree source for Exynos5433-based Samsung TM2E
board. TM2E board is very similar to the TM2 board so the
exynos5433-tm2e.dts includes the TM2 DTS and overrides the differences.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Ingi kim <ingi2.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds the Device Tree source for Exynos5433-based Samsung TM2
board.
This patch adds support for following devices:
1. basic SoC
- Initial booting for Samsung Exynos5433 SoC
- DRAM LPDDR3 (3GB)
- eMMC (32GB)
- ARM architecture timer
2. power management devices
- Sasmung S2MPS13 PMIC for the power supply
- CPUFREQ for big.LITTLE cores
- TMU for big.LITTLE cores and GPU
- ADC with thermistor to measure the temperature of AP/Battery/Charger
- Maxim MAX77843 Interface PMIC (MUIC/Haptic/Regulator)
3. sound devices
- I2S for sound bus
- LPASS for sound power control
- Wolfson WM5110 for sound codec
- Maxim MAX98504 for speaker amplifier
- TM2 ASoC Machine device driver node
3. display devices
- DECON, DSI and MIC for the panel output
4. USB devices
- USB 3.0 DRD (Dual Role Device)
- USB 3.0 Host controller
5. storage devices
- MSHC (Mobile Storage Host Controller) for eMMC device
6. misc devices
- gpio-keys (power, volume up/down, home key)
- PWM (Pulse Width Modulation Timer)
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Ingi kim <ingi2.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
[Maxime: Change title prefix to match the usual style]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A64 SoC is a low-cost chip with 4 ARM Cortex-A53 cores
and the typical tablet / TV box peripherals.
The SoC is based on the (32-bit) Allwinner H3 chip, sharing most of
the peripherals and the memory map.
Although the cores are proper 64-bit ones, the whole SoC is actually
limited to 4GB (including all the supported DRAM), so we use 32-bit
address and size cells. This has the nice feature of us being able to
reuse the DT for 32-bit kernels as well.
This .dtsi lists the hardware that we support so far.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
[Maxime: Convert to CCU binding, drop the MMC support for now]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the A64 CCU clocks set.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
H3 SPI has same architecture as A31 except FIFO capacity.
To configure the buffer size separately, compatible property should be
different. Optional DMA specifiers and example are added.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add DT bindings for the Renesas R-Car Reset Controller (R-Car Gen1
RESET/WDT and R-Car Gen2/Gen3 and RZ/G RST).
As the features provided by the hardware module differ a lot across the
various SoC families and members, only SoC-specific compatible values
are defined.
For now we use the RST only for providing access to the state of the
mode pins, which is needed by the clock driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Document the SK-RZG1M device tree bindings, listing it as a supported board.
This allows to use checkpatch.pl to validate .dts files referring to the
SK-RZG1M board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add minimal support for the RZ/G1M (R8A7743) SoC.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There are display panels which demands that the sync signal is driven on
different edge than the pixel data.
With the syncclk-active property we can specify the clk edge to be used to
drive the sync signal. When the property is missing it indicates that the
sync is driven on the same edge as the pixel data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Rob Herring <robh+dt@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
CC: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add device tree support for the tsl2583 IIO driver with no custom
properties.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds devicetree support for the si7020 iio driver. Since it works
well without requiring any additional property, its compatible string is
added to the trivial i2c devices bindings list.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The type of AVIC interrupt controller found on i.MX31 is one-cell,
namely 31 for CCM DVFS and 53 for CCM, however for clock control
module its interrupts are specified as 3-cells, fix it.
Fixes: ef0e4a606f ("ARM: mx31: Replace clk_register_clkdev with clock DT lookup")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the binding document for the new brcmstb-avs-cpufreq driver.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
stm32 pinctrl driver could be probed even if no interrupt controller
is defined to manage gpio irqs. Entries related to gpio irq management
are moved to optional.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The address of the mailbox node in the example has a typo.
So fix it accordingly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: d4b5c782b9 ("dt/bindings: Add binding for the BCM2835 mailbox driver")
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch introduces a vendor prefix for Holtek Semiconductor Inc.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for pin output control through the pinctrl config:
- support enabling/disabling output on a given pin
- support output level setting (high or low)
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add power dt-bindings for MT2701.
Signed-off-by: Shunli Wang <shunli.wang@mediatek.com>
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This resolves a merge issue with
drivers/staging/iio/accel/sca3000_core.c and we want the fixes all in
here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from David Miller:
"Lots of fixes, mostly drivers as is usually the case.
1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
Khoroshilov.
2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
Pedersen.
3) Don't put aead_req crypto struct on the stack in mac80211, from
Ard Biesheuvel.
4) Several uninitialized variable warning fixes from Arnd Bergmann.
5) Fix memory leak in cxgb4, from Colin Ian King.
6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.
7) Several VRF semantic fixes from David Ahern.
8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.
9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.
10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.
11) Fix stale link state during failover in NCSCI driver, from Gavin
Shan.
12) Fix netdev lower adjacency list traversal, from Ido Schimmel.
13) Propvide proper handle when emitting notifications of filter
deletes, from Jamal Hadi Salim.
14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.
15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.
16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.
17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.
18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
Leitner.
19) Revert a netns locking change that causes regressions, from Paul
Moore.
20) Add recursion limit to GRO handling, from Sabrina Dubroca.
21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.
22) Avoid accessing stale vxlan/geneve socket in data path, from
Pravin Shelar"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
geneve: avoid using stale geneve socket.
vxlan: avoid using stale vxlan socket.
qede: Fix out-of-bound fastpath memory access
net: phy: dp83848: add dp83822 PHY support
enic: fix rq disable
tipc: fix broadcast link synchronization problem
ibmvnic: Fix missing brackets in init_sub_crq_irqs
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
net/mlx4_en: Save slave ethtool stats command
net/mlx4_en: Fix potential deadlock in port statistics flow
net/mlx4: Fix firmware command timeout during interrupt test
net/mlx4_core: Do not access comm channel if it has not yet been initialized
net/mlx4_en: Fix panic during reboot
net/mlx4_en: Process all completions in RX rings after port goes up
net/mlx4_en: Resolve dividing by zero in 32-bit system
net/mlx4_core: Change the default value of enable_qos
net/mlx4_core: Avoid setting ports to auto when only one port type is supported
net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
...
The MAC is capable of RGMII mode and that is probably a more typical
connection type than GMII today (eg it is used by Marvell Reference
designs for several SOCs). Let DT users specify the standard
phy-connection-type = "rgmii-id";
On a phy node.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We haven't seen a whole lot of fixes for the first two weeks since the merge
window, but here is the batch that we have at the moment.
Nothing sticks out as particularly bad or scary, it's mostly a handful of
smaller fixes to several platforms. The Uniphier reset controller changes
could probably have been delayed to 4.10, but they're not scary and just
plumbing up driver changes that went in during the merge window.
We're also adding another maintainer to Marvell Berlin platforms, to help
out when Sebastian is too busy. Yay teamwork!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OGbj
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We haven't seen a whole lot of fixes for the first two weeks since the
merge window, but here is the batch that we have at the moment.
Nothing sticks out as particularly bad or scary, it's mostly a handful
of smaller fixes to several platforms. The Uniphier reset controller
changes could probably have been delayed to 4.10, but they're not
scary and just plumbing up driver changes that went in during the
merge window.
We're also adding another maintainer to Marvell Berlin platforms, to
help out when Sebastian is too busy. Yay teamwork!"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
ARM: dts: vf610: fix IRQ flag of global timer
ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
ARM: imx: gpc: Initialize all power domains
arm64: dts: Updated NAND DT properties for NS2 SVK
arm64: dts: uniphier: change MIO node to SD control node
ARM: dts: uniphier: change MIO node to SD control node
reset: uniphier: rename MIO reset to SD reset for Pro5, PXs2, LD20 SoCs
arm64: uniphier: select ARCH_HAS_RESET_CONTROLLER
ARM: uniphier: select ARCH_HAS_RESET_CONTROLLER
arm64: dts: Add timer erratum property for LS2080A and LS1043A
arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
ARM: multi_v7_defconfig: Enable Intel e1000e driver
MAINTAINERS: add myself as Marvell berlin SoC maintainer
bus: qcom-ebi2: depend on ARCH_QCOM or COMPILE_TEST
ARM: dts: fix the SD card on the Snowball
arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
arm64: dts: marvell: fix clocksource for CP110 master SPI0
ARM: mvebu: Select corediv clk for all mvebu v7 SoC
Here are a number of small tty and serial driver fixes for reported
issues for 4.9-rc3. Nothing major, but they do resolve a bunch of
problems with the tty core changes that are in 4.9-rc1, and finally the
atmel serial driver is back working properly.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlgU0WQPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspwmIAoJYQ
5fdXVYgwh59wn0E4xuKWSH84AJ9bTIe3MDED9TrE1rocnLaj9wxIuw==
=os0d
-----END PGP SIGNATURE-----
Merge tag 'tty-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small tty and serial driver fixes for reported
issues for 4.9-rc3. Nothing major, but they do resolve a bunch of
problems with the tty core changes that are in 4.9-rc1, and finally
the atmel serial driver is back working properly.
All have been in linux-next with no reported issues"
* tag 'tty-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial_core: fix NULL struct tty pointer access in uart_write_wakeup
tty: serial_core: Fix serial console crash on port shutdown
tty/serial: at91: fix hardware handshake on Atmel platforms
vt: clear selection before resizing
sc16is7xx: always write state when configuring GPIO as an output
sh-sci: document R8A7743/5 support
tty: serial: 8250: 8250_core: NXP SC16C2552 workaround
tty: limit terminal size to 4M chars
tty: serial: fsl_lpuart: Fix Tx DMA edge case
serial: 8250_lpss: enable MSI for sure
serial: core: fix console problems on uart_close
serial: 8250_uniphier: fix clearing divisor latch access bit
serial: 8250_uniphier: fix more unterminated string
serial: pch_uart: add terminate entry for dmi_system_id tables
devicetree: bindings: uart: Add new compatible string for ZynqMP
serial: xuartps: Add new compatible string for ZynqMP
serial: SERIAL_STM32 should depend on HAS_DMA
serial: stm32: Fix comparisons with undefined register
tty: vt, fix bogus division in csi_J
Here are a number of small USB driver fixes for 4.9-rc3. There is the
usual number of gadget and xhci patches in here to resolved reported
issues, as well as some usb-serial driver fixes and new device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlgU0foPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspqE4Ani3Y
N4J9W4SeXT7ilLLQoeLznUv8AJ4sm/Uy5d4syBa+TVEPuAHXort+vw==
=ICZX
-----END PGP SIGNATURE-----
Merge tag 'usb-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for 4.9-rc3.
There is the usual number of gadget and xhci patches in here to
resolved reported issues, as well as some usb-serial driver fixes and
new device ids.
All have been in linux-next with no reported issues"
* tag 'usb-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
usb: chipidea: host: fix NULL ptr dereference during shutdown
usb: renesas_usbhs: add wait after initialization for R-Car Gen3
usb: increase ohci watchdog delay to 275 msec
usb: musb: Call pm_runtime from musb_gadget_queue
usb: musb: Fix hardirq-safe hardirq-unsafe lock order error
usb: ehci-platform: increase EHCI_MAX_RSTS to 4
usb: ohci-at91: Set RemoteWakeupConnected bit explicitly.
USB: serial: fix potential NULL-dereference at probe
xhci: use default USB_RESUME_TIMEOUT when resuming ports.
xhci: workaround for hosts missing CAS bit
xhci: add restart quirk for Intel Wildcatpoint PCH
USB: serial: cp210x: fix tiocmget error handling
wusb: fix error return code in wusb_prf()
Revert "Documentation: devicetree: dwc2: Deprecate g-tx-fifo-size"
Revert "usb: dwc2: gadget: fix TX FIFO size and address initialization"
Revert "usb: dwc2: gadget: change variable name to more meaningful"
USB: serial: ftdi_sio: add support for Infineon TriBoard TC2X7
wusb: Stop using the stack for sg crypto scratch space
usb: dwc3: Fix size used in dma_free_coherent()
usb: gadget: f_fs: stop sleeping in ffs_func_eps_disable
...
This patch adds the QSPI clock for stm32f469 discovery board.
The gate mapping is a little bit different from stm32f429 soc.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some resources, such as IPPC register etc, shared with device
driver are moved into common glue layer when xHCI driver is the
host side of dual-role mode and they should be changed as optional
properties if they are required ones before. For clarity, add
a new part of binding to support host side of dual-role mode.
Additionally add optional properties of pinctrl for host only mode
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Renesas RZ/G SoC also have the SCIF, SCIFA, SCIFB, and HSCIF ports and
they seem compatible with the R-Car gen2 SoC in this respect...
Document RZ/G1[ME] (also known as R8A774[35]) SoC bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch Adds the new compatible string for ZynqMP SoC.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The FCP IP cores include a version register that identifies which SoC
model the IP is integrated in. SoC-specific compatible strings are not
needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Texas Instrument's System Control Interface (TI-SCI) Message Protocol
is used in Texas Instrument's System on Chip (SoC) such as those in
newer SoCs in the keystone processor family starting with K2G.
This message protocol is used to communicate between various compute
or processing entities (such as ARM, DSP etc.) with a central system
controller entity.
TI-SCI message protocol provides support for management of various
hardware entities within the SoC.
The message protocol can be found here:
http://processors.wiki.ti.com/index.php/TISCI
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This updates the Device Tree according to the preferred way of parsing
the nodes using the regulator framework.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds device tree bindings for the MPU-3050 gyroscope. Since it
is the first set of bindings for a gyroscope, the folder for it
is also created.
Cc: devicetree@vger.kernel.org
Cc: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Due to the DMIC that needs time to initial after the MCLK is provided, the
field of delay time is implemented by the platform data.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of fixes for the uniphier clk driver that was introduced recently, as well as
Kconfig option hiding, module autoloading markings, and a few fixes for clk_hw
based registration patches that went in this merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=mWXv
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"This is the first batch of clk driver fixes for this release.
We have a handful of fixes for the uniphier clk driver that was
introduced recently, as well as Kconfig option hiding, module
autoloading markings, and a few fixes for clk_hw based registration
patches that went in this merge window"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: at91: Fix a return value in case of error
clk: uniphier: rename MIO clock to SD clock for Pro5, PXs2, LD20 SoCs
clk: uniphier: fix memory overrun bug
clk: hi6220: use CLK_OF_DECLARE_DRIVER for sysctrl and mediactrl clock init
clk: mvebu: armada-37xx-periph: Fix the clock gate flag
clk: bcm2835: Clamp the PLL's requested rate to the hardware limits.
clk: max77686: fix number of clocks setup for clk_hw based registration
clk: mvebu: armada-37xx-periph: Fix the clock provider registration
clk: core: add __init decoration for CLK_OF_DECLARE_DRIVER function
clk: mediatek: Add hardware dependency
clk: samsung: clk-exynos-audss: Fix module autoload
clk: uniphier: fix type of variable passed to regmap_read()
clk: uniphier: add system clock support for sLD3 SoC
i.MX6UL does only require three clocks to enable CAAM module.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The text states that default-input is an endpoint property, but in the
example it is a device property.
The default input is a property of the chip, not of a particular port, so
the example makes more sense.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds support for the wm8581 codec to the wm8580 driver.
The wm8581 codec hardware adds a fourth DAC and otherwise is
compatible with the wm8580 codec.
of_device_id data is used to allow the driver to select the
suitable DAC count specified in the device tree codec selection.
The wm8580_driver_data struct is used to store the number of DACs.
The snd_soc_dai_driver no longer lists the channels_max for the
playback substream. This variable is set during the i2c probe
from the of_device_id supplied wm8580_driver_data struct.
With knowledge of the number of DACs in use, the DAC4 controls,
widgets and routes are added as required for DAC4.
The device tree documentation for the wm8580 is altered to list
the wm8581 codec support, as is the Kconfig file.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support to multi codec, as the msm8916 codec is now
split into two codecs, Analog and Digital.
Also update the bindings and example to show that the card supports
multicodec.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch removes capture-dai property which should not have existed
in this document in the first place. It looks like leftover from old
version of patches by mistake.
Remove it to avoid any confusion in future.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd codec is found in Qualcomm msm8916 and apq8016 processors.
This codec IP is split in to two parts(Digital & Analog).
Analog part is integrated in to PMIC PM8916 and the digital part is
integrated into Application processor. Data transfer between Analog and
Digital Die is done via a internal bus called PDM.
This patch adds support to Digital part of the Codec which is integrated
into Application Processor.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd codec is found in Qualcomm msm8916 and apq8016 processors.
This codec IP is split in to two parts (Digital & Analog).
Analog part is integrated in to PMIC PM8916 and the digital part is
integrated into Application processor. Data transfer between Analog and
Digital Die is done via a internal bus called PDM.
This patch adds support to Analog part of the Codec which is integrated
into PMIC PM8916.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "rt5668" codec supported in this driver is actually a revision
of "rt5663". So the patch is renamed to "rt5663 v2"
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the I2C sx150x GPIO expander driver uses platform_data to manage
the pins configurations, rewrite the driver as a pinctrl driver using
pinconf to get/set pin configurations from DT or debugfs.
The pinctrl driver is functionnally equivalent as the gpio-only driver
and can use DT for pinconf. The platform_data confirmation is dropped.
This patchset removed the gpio-only driver and selects the Pinctrl driver
config instead. This patchset also migrates the gpio dt-bindings to pinctrl
and add the pinctrl optional properties.
The driver was tested with a SX1509 device on a BeagleBone black with
interrupt support and on an X86_64 machine over an I2C to USB converter.
This is a fixed version that builds and runs on non-OF platforms and on
arm based OF. The GPIO version is removed and the bindings are also moved
to the pinctrl bindings.
Changes since v2
- rebased on v4.9-rc1
- removed MODULE_DEVICE_TABLE as in upstream bb411e771b
("gpio: sx150x: fix implicit assumption module.h is present")
Changes since v1
- Fix Kconfig descriptions on pinctrl and gpio
- Fix Kconfig dependency
- Remove oscio support for non-789 devices
- correct typo in dt bindings
- remove probe reset for non-789 devices
Changes since RFC
- Put #ifdef CONFIG_OF/CONFIG_OF_GPIO to remove OF code for non-of platforms
- No more rely on OF_GPIO config
- Moved and enhanced bindings to pinctrl bindings
- Removed gpio-sx150x.c
- Temporary select PINCTRL_SX150X when GPIO_SX150X
- Temporary mark GPIO_SX150X as deprecated
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
ested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The generic pin configuration and multiplexing should be preferred now,
even though we still support the old one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The previous patch renamed several files that are cross-referenced
along the Kernel documentation. Adjust the links to point to
the right places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fair number of outreachy related patches in here. Some of these may well
have already been picked up by Greg but git will sort that out for us.
Also some good staging cleanup work from other sources. Thanks Brian and Lars
in particular for this.
New device support
* ACCES 104-quad-8
- New driver for this 8 channel encoder input board. Lots of new ABI with
this one.
* AD7766
- New driver supporting AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1 and
AD7767-2 24 bit ADCs.
* dmard 10
- New driver for this 3 axis accelerometer.
* Honeywell ABP pressure sensors.
- New driver covering 56 parts in this series (too many to list here!)
* HTS221
- New driver to support this relative humidiy and temperature device.
* LMP91000
- New driver for this potentiostat (form of chemical sensor). Nice example
of use of the buffered consumer interfaces and the use of a consumer
provided trigger.
* MiraMEMS DA311
- New driver for this 3 axis accelerometer.
* MiraMEMS DA280
- New driver for this 3 axis accelerometer. Follow up caught up with
vendor prefixes for these.
Staging graduations
* isl29018 light sensor
- Fixes and cleanups listed below (thanks for your hard work on this Brian!)
* sca3000
- Fixes and cleanups listed below. This was one of the small set of drivers
that went into staging when IIO was first added. Turns out it had a few
bugs and needed to be brought into the modern era! Not clear if I am
the only person who actually has one of these still wired to a board.
New features (Core)
- Add an iio_trigger_validate_own_device helper which relies on the device
and trigger having the same parent. Convenient to have this for some
of the more complex trigger / device interactions. Was hand rolled in
a few drivers already so good to bring it into the core.
- Add an iio_read_channel_offset in kernel access helper (similar to
the existing one for scale).
- IIO_ATTR_{RO, WO, RW} and IIO_DEVICE_ATTR_{RO, WO, RW} macros. These
lead some rather contrived function naming, but there is no denying they
do reduced boilerplate. I'm going to resist their introduction in
drivers 'unless' they form part of a larger set of cleanups.
- Counter channel type and index type.
New features (Drivers)
* hdc100x
- Triggered buffer support.
* mcp4725
- Device tree bindings and support.
- Voltage reference selection.
* ti-adc0832
- Triggered buffer support.
* ti-adc161s626
- Add regulator support allowing _scale and _offset values to be established
and exported.
New features (Tools)
* iio_generic_buffer
- -A option to force enable all channels rather than faulting if some are
already enabled (like -a does). Followup patches tidied this support up.
Cleanups (Core)
- Use kmalloc_array in iio_scan_mask_set.
- Take event_attrs field of iio_info structure constant
- Staging todo list updates. Most of it was long done.
- MAINTAINERS had a wrong directory listing.
Cleanups (Drivers)
* Missing i2c trivial devices entries.
* ad5592r
- Fix an endian type related sparse warnings.
* ad7150
- Constify the event attribute_group structures.
* ad7152
- Add some blank lines to improve readability.
- Sampling frequency control via chan-info element rather than hand rolled
attributes.
- add a new lock to avoid use of mlock for non state change related locking.
* ad7280
- Constify atrribute_group structure (second patch covers the event ones)
* ad7606 (Lars is driving most of the cleanup on this with some additions from
Eva)
- Fix improper setting of oversampling pins. This has been broken a very
long time in this staging driver, so not going to push this back to stable.
- Implement oversampling configuration via the chan_info mask element.
- Remove an unused int_vref_mv field.
- Remove a reundant name field from ad7606_chip_info.
- Remove default device configuration from platform_data in favour of
whatever the power on defaults are.
- Remove out of band error reporting in the kernel log as not providing
much information.
- Fix oversampling ratio by having 1 be the value for no oversampling.
- Avoid allocating buffer for each data capture.
- Factor out common code between periodic and one-shot capture.
- Move set_drvdat into common code.
- Let the common probe function return int rather than jumping through
an ERR_PTR.
- Pass struct device * into common remove to simplify code.
- Always run trigger handler only once per event (no one can remember why
it was being possibly done twice).
- Move over to the GPIO descriptor API to shorten and clarify code.
- Move the buffer code into the main file as it's not optional and is
now rather short in this driver.
- Fix the naming of the supply regulator.
- Rework regulator handling to handle errors including deferred probing.
- Tidy up a ptr_err or 0 return.
* ad7746
- Sampling frequency control via info_mask element rather than hand rolled
* ad7758
- Sampling frequency control via info_mask element rather than hand rolled
attributes.
* ad7816
- Constify the event attribute_group structure.
* adt7316
- Constify the event attribute group structures.
* ak8974
- Cleanup some sparse warnings about endian types.
* ak8975
- Cleanup some sparse warnings about endian types.
* bmi160
- Spare endian warning cleanups.
* isl29018 (towards staging graduation)
- Remove unusedvariables and defines.
- Improve consistency of error handling.
- Signed / unsigned comparison fixes.
- Use the IIO_DEVICE_ATTR_{RO, RW} macros
- Fix a race in in_illuminance_scale_available_show.
- Cleanup exit points of _read_raw
- Sanity check if in suspended state during a write_raw call as was already
done for read_raw.
- Document device tree bidnings.
- Document infrared supression controls.
- Add some newlines to improve readability and drop one that shouldn't be
there.
- Fix a poorly named functions name.
- Fix multiline coment syntax.
- Tidy up a pair or return statements by unifying them.
- Rename description in Kconfig for consistency with similar drivers.
* lidar
- cleanup power management by dropping unnecessary call.
* ltr501
- Use the claim_direct_mode helpers. Fix a race condition along the way.
* max1027
- Fix a dubious x | !y sparse warning.
- Use the new iio_trigger_validate_own_device helper.
* max440000
- Clean up some sparse warnings about endian types.
* mcp4725
- Use the regulator framework to establish the reference voltage rather than
getting it from platform data.
- Tidy up a comment typo.
- Fix a wrong PTR_ERR query (wrong regulator).
* mma7660
- Take a mma7660_nscale static.
* mma8452
- Use the new iio_trigger_validate_own_device helper.
- Use claim_direct_mode helpers - fix a race condition along the way.
* mpl3115
- Use claim_direct_mode helpers - fix a race condition along the way.
* ms65611
- Tidy up regulator error handling and clean out a static warning in the mix.
* sca3000
- Avoid a potential unitialized variable if a hardware read returns a value
that isn't actually supported (mostly warning supression).
- Fix a use before setting of the indio_dev->buffer pointer. Broken for
a very long time so not going to rush this into stable.
- Merge buffer file with core file. We used to always split these.
Sometimes it's just not worth the hassle. In this case the device's main
feature is it's hardware fifos so unlikely anyone would want to run it
without.
- Drop the sca3000_register_ring_funcs function as it's a pointless wrapper
once we have only one file.
- Fix cleaning of flag + setting of size of scan. Without this you can't
start the buffer twice and expect sensible (or any) results. Again,
broken for a long time so not heading for stable.
- Drop the custom watershed setting ABI - for now we'll just support one
value.
- Move to a hybrid hard / soft buffer design (how we've been doing it
for similar devices for a while now!)
- Cleanup some unusued variables.
- Use a fake channel to support core handling of freefall event registration.
- Cleanup the register defines.
- Fix an off by one error in axis due to IIO_NO_MOD taking up the 0 value.
Been broken since first admission of IIO to the staging tree.
- Add readback of the 3db low pass filter frequency and later writing
allowing droppign of custom measurement mode attributes as they can
be represented by the filter choices that is their main characteristic.
- Drop non standard revision attr and replace with dev_info on probe.
- Avoid a race in probe.
- Various formatting fixes.
- Kernel-docify docs that were very nearly in the write format.
* tsl2583
- Constify attribute_group structure.
* zpa2326
- Drop a redundant DEBUG ifdef.
Cleanups (Tools)
* iio_generic_buffer
- Fix the ? arguement. Previously it sort of worked as you got the help
message as a result of it not recognising the arguement.
-----BEGIN PGP SIGNATURE-----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=ZRUt
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.10a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.10 cycle.
Fair number of outreachy related patches in here. Some of these may well
have already been picked up by Greg but git will sort that out for us.
Also some good staging cleanup work from other sources. Thanks Brian and Lars
in particular for this.
New device support
* ACCES 104-quad-8
- New driver for this 8 channel encoder input board. Lots of new ABI with
this one.
* AD7766
- New driver supporting AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1 and
AD7767-2 24 bit ADCs.
* dmard 10
- New driver for this 3 axis accelerometer.
* Honeywell ABP pressure sensors.
- New driver covering 56 parts in this series (too many to list here!)
* HTS221
- New driver to support this relative humidiy and temperature device.
* LMP91000
- New driver for this potentiostat (form of chemical sensor). Nice example
of use of the buffered consumer interfaces and the use of a consumer
provided trigger.
* MiraMEMS DA311
- New driver for this 3 axis accelerometer.
* MiraMEMS DA280
- New driver for this 3 axis accelerometer. Follow up caught up with
vendor prefixes for these.
Staging graduations
* isl29018 light sensor
- Fixes and cleanups listed below (thanks for your hard work on this Brian!)
* sca3000
- Fixes and cleanups listed below. This was one of the small set of drivers
that went into staging when IIO was first added. Turns out it had a few
bugs and needed to be brought into the modern era! Not clear if I am
the only person who actually has one of these still wired to a board.
New features (Core)
- Add an iio_trigger_validate_own_device helper which relies on the device
and trigger having the same parent. Convenient to have this for some
of the more complex trigger / device interactions. Was hand rolled in
a few drivers already so good to bring it into the core.
- Add an iio_read_channel_offset in kernel access helper (similar to
the existing one for scale).
- IIO_ATTR_{RO, WO, RW} and IIO_DEVICE_ATTR_{RO, WO, RW} macros. These
lead some rather contrived function naming, but there is no denying they
do reduced boilerplate. I'm going to resist their introduction in
drivers 'unless' they form part of a larger set of cleanups.
- Counter channel type and index type.
New features (Drivers)
* hdc100x
- Triggered buffer support.
* mcp4725
- Device tree bindings and support.
- Voltage reference selection.
* ti-adc0832
- Triggered buffer support.
* ti-adc161s626
- Add regulator support allowing _scale and _offset values to be established
and exported.
New features (Tools)
* iio_generic_buffer
- -A option to force enable all channels rather than faulting if some are
already enabled (like -a does). Followup patches tidied this support up.
Cleanups (Core)
- Use kmalloc_array in iio_scan_mask_set.
- Take event_attrs field of iio_info structure constant
- Staging todo list updates. Most of it was long done.
- MAINTAINERS had a wrong directory listing.
Cleanups (Drivers)
* Missing i2c trivial devices entries.
* ad5592r
- Fix an endian type related sparse warnings.
* ad7150
- Constify the event attribute_group structures.
* ad7152
- Add some blank lines to improve readability.
- Sampling frequency control via chan-info element rather than hand rolled
attributes.
- add a new lock to avoid use of mlock for non state change related locking.
* ad7280
- Constify atrribute_group structure (second patch covers the event ones)
* ad7606 (Lars is driving most of the cleanup on this with some additions from
Eva)
- Fix improper setting of oversampling pins. This has been broken a very
long time in this staging driver, so not going to push this back to stable.
- Implement oversampling configuration via the chan_info mask element.
- Remove an unused int_vref_mv field.
- Remove a reundant name field from ad7606_chip_info.
- Remove default device configuration from platform_data in favour of
whatever the power on defaults are.
- Remove out of band error reporting in the kernel log as not providing
much information.
- Fix oversampling ratio by having 1 be the value for no oversampling.
- Avoid allocating buffer for each data capture.
- Factor out common code between periodic and one-shot capture.
- Move set_drvdat into common code.
- Let the common probe function return int rather than jumping through
an ERR_PTR.
- Pass struct device * into common remove to simplify code.
- Always run trigger handler only once per event (no one can remember why
it was being possibly done twice).
- Move over to the GPIO descriptor API to shorten and clarify code.
- Move the buffer code into the main file as it's not optional and is
now rather short in this driver.
- Fix the naming of the supply regulator.
- Rework regulator handling to handle errors including deferred probing.
- Tidy up a ptr_err or 0 return.
* ad7746
- Sampling frequency control via info_mask element rather than hand rolled
* ad7758
- Sampling frequency control via info_mask element rather than hand rolled
attributes.
* ad7816
- Constify the event attribute_group structure.
* adt7316
- Constify the event attribute group structures.
* ak8974
- Cleanup some sparse warnings about endian types.
* ak8975
- Cleanup some sparse warnings about endian types.
* bmi160
- Spare endian warning cleanups.
* isl29018 (towards staging graduation)
- Remove unusedvariables and defines.
- Improve consistency of error handling.
- Signed / unsigned comparison fixes.
- Use the IIO_DEVICE_ATTR_{RO, RW} macros
- Fix a race in in_illuminance_scale_available_show.
- Cleanup exit points of _read_raw
- Sanity check if in suspended state during a write_raw call as was already
done for read_raw.
- Document device tree bidnings.
- Document infrared supression controls.
- Add some newlines to improve readability and drop one that shouldn't be
there.
- Fix a poorly named functions name.
- Fix multiline coment syntax.
- Tidy up a pair or return statements by unifying them.
- Rename description in Kconfig for consistency with similar drivers.
* lidar
- cleanup power management by dropping unnecessary call.
* ltr501
- Use the claim_direct_mode helpers. Fix a race condition along the way.
* max1027
- Fix a dubious x | !y sparse warning.
- Use the new iio_trigger_validate_own_device helper.
* max440000
- Clean up some sparse warnings about endian types.
* mcp4725
- Use the regulator framework to establish the reference voltage rather than
getting it from platform data.
- Tidy up a comment typo.
- Fix a wrong PTR_ERR query (wrong regulator).
* mma7660
- Take a mma7660_nscale static.
* mma8452
- Use the new iio_trigger_validate_own_device helper.
- Use claim_direct_mode helpers - fix a race condition along the way.
* mpl3115
- Use claim_direct_mode helpers - fix a race condition along the way.
* ms65611
- Tidy up regulator error handling and clean out a static warning in the mix.
* sca3000
- Avoid a potential unitialized variable if a hardware read returns a value
that isn't actually supported (mostly warning supression).
- Fix a use before setting of the indio_dev->buffer pointer. Broken for
a very long time so not going to rush this into stable.
- Merge buffer file with core file. We used to always split these.
Sometimes it's just not worth the hassle. In this case the device's main
feature is it's hardware fifos so unlikely anyone would want to run it
without.
- Drop the sca3000_register_ring_funcs function as it's a pointless wrapper
once we have only one file.
- Fix cleaning of flag + setting of size of scan. Without this you can't
start the buffer twice and expect sensible (or any) results. Again,
broken for a long time so not heading for stable.
- Drop the custom watershed setting ABI - for now we'll just support one
value.
- Move to a hybrid hard / soft buffer design (how we've been doing it
for similar devices for a while now!)
- Cleanup some unusued variables.
- Use a fake channel to support core handling of freefall event registration.
- Cleanup the register defines.
- Fix an off by one error in axis due to IIO_NO_MOD taking up the 0 value.
Been broken since first admission of IIO to the staging tree.
- Add readback of the 3db low pass filter frequency and later writing
allowing droppign of custom measurement mode attributes as they can
be represented by the filter choices that is their main characteristic.
- Drop non standard revision attr and replace with dev_info on probe.
- Avoid a race in probe.
- Various formatting fixes.
- Kernel-docify docs that were very nearly in the write format.
* tsl2583
- Constify attribute_group structure.
* zpa2326
- Drop a redundant DEBUG ifdef.
Cleanups (Tools)
* iio_generic_buffer
- Fix the ? arguement. Previously it sort of worked as you got the help
message as a result of it not recognising the arguement.
I was on vacation during the merge window (a long vacation)
but this is a bug fix that should go in and a new driver that shouldn't
hurt anything.
This has been in linux-next for a month or so.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlgKVpoACgkQIXnXXONXERdGBACeONBS0wOf4Rv+bxSOdeJcTwLJ
rmoAoJ2R0BpWE1imvcC+AqXOoqg2c48k
=P4Dz
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.9-2' of git://git.code.sf.net/p/openipmi/linux-ipmi
Pull IPMI updates from Corey Minyard:
"A small bug fix and a new driver for acting as an IPMI device.
I was on vacation during the merge window (a long vacation) but this
is a bug fix that should go in and a new driver that shouldn't hurt
anything.
This has been in linux-next for a month or so"
* tag 'for-linus-4.9-2' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: fix crash on reading version from proc after unregisted bmc
ipmi/bt-bmc: remove redundant return value check of platform_get_resource()
ipmi/bt-bmc: add a dependency on ARCH_ASPEED
ipmi: Fix ioremap error handling in bt-bmc
ipmi: add an Aspeed BT IPMI BMC driver
Add OX820 bindings and remove clock indices from bindings since they are present
in the dt-bindings headers files.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20161005150752.22618-7-narmstrong@baylibre.com
Pull timer updates from Thomas Gleixner:
"This updates contains:
- A revert which addresses a boot failure on ARM Sun5i platforms
- A new clocksource driver, which has been delayed beyond rc1 due to
an interrupt driver issue which was unearthed by this driver. The
debugging of that issue and the discussion about the proper
solution made this driver miss the merge window. There is no point
in delaying it for a full cycle as it completes the basic mainline
support for the new JCore platform and does not create any risk
outside of that platform"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "clocksource/drivers/timer_sun5i: Replace code by clocksource_mmio_init"
clocksource: Add J-Core timer/clocksource driver
of: Add J-Core timer bindings
Add NAND driver to support the Oxford Semiconductor OX820 NAND Controller.
This is a simple memory mapped NAND controller with single chip select and
software ECC.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
I made a mistake as for naming for this block. The MIO block is not
implemented for these 3 SoCs in the first place. The current naming
will be a trouble if an SoC with both MIO and SD-ctrl blocks appear
in the future.
This driver has just been merged in the previous merge window.
Rename it before the release.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Update DT bindings to describe idle states of PM domains.
This patch is based on the original patch by Marc Titinger.
Signed-off-by: Marc Titinger <mtitinger+renesas@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
MK808 is a tv stick which has rockchip rk3066 CPU inside, two usb ports
- host and otg, micro sd card slot and onboard wifi RK901.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chip.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Sergei Shtylyov